st 120 uapdh

Transcription

st 120 uapdh
ST_120_UAPDH_Sell_Sheet.qx_ST_120_UAPDH 12/29/11 4:10 PM Page 1
ST 120 UAPDH
The Kanaflex ST 120 UAPDH all-purpose drop hose provides the solution to today’s
challenging need for a better hose for the transfer of blended gasoline, ethanol,
biodiesel, kerosene, and diesel products. Produced of clear non-permeable
polyurethane, the ST 120 UAPDH is a lightweight and flexible hose that will meet
your needs for an all-purpose drop hose.
ST_120_UAPDH_Sell_Sheet.qx_ST_120_UAPDH 12/29/11 4:10 PM Page 2
ST 120 UAPDH
The ultimate all purpose tank truck drop hose with clear static
dissipating tube and static grounding wire
Lightweight and flexible . . . even in
sub-zero temperatures
External helix . . . for easy drag and
impact/abrasion protection
Polyurethane inner and outer tube . . .
clear, non-permeable, static dissipating, allows
visual confirmation of flow; provides maximum
resistance to gasoline, biodiesel, ethanol, etc.
Stranded copper static wire . . . proper
grounding eliminates static electricity
Braided reinforcement . . . provides
strength and reduces stretch
Banding Coil (black or white)
Temp. Range: -52°F to 140°F
Applications: All purpose tank truck gravity drop hose for items such as gasoline,
ethanol, biodiesel, kerosene and diesel.
Construction: Non-permeable polyurethane inner and outer tube with synthetic braiding,
smooth bore, corrugated O.D., PVC helix for easy drag, clear static dissipating tube and
multi-strand copper static wire providing maximum protection against static discharge.
Note: Lightweight and flexible even in sub-zero temperatures. Static dissipating
polyurethane inner and outer tube provides maximum resistance to gasoline, biodiesel
(up to B100 compliant with ASTM D6751), ethanol (up to E85; currently testing E100),
kerosene, diesel and ASTM fuel oils. Clear tube allows visual confirmation of flow.
Banding coil or banding sleeve must be used for all sizes. Static wire must be properly
imbedded during fitting installation and tested to assure proper static grounding of hose
to a grounded system.
Inside Outside
Dia.
Dia.
Inches Inches
3
3.72
4
4.81
Pitch
Inches
0.62
0.68
Minimum
Bend Radius
72°F, Inches
6.3
7.0
Working
Vacuum Weight
Pressure
Rating
72°F, P.S.I. 72°F, In Hg Lbs/Ft
65
29.8
1.40
65
29.8
1.87
Standard
Length
Ft
60,100
60,100
The PVC
banding coil is
designed to fit
the corrugation
of the ST 120
UAPDH hose. Provides a smooth surface
for banding. Use approximately 4" of
banding coil to cover a 9" length of each
end of the hose.
Banding Sleeve
Plastic
banding
sleeve for
use with
ST 120 UAPDH hose. 9" sections are
recommended at each end of the ST 120
UAPDH tank truck drop hose. Available
in 3" and 4" sizes.
Note: Over flexing or repeated flexing of hose within 18" of fitting is a common cause of hose failure.
Installing a 12" - 14" section of our Banding Coil at the end of the hose should be considered.
Kanaflex will not be responsible for damage to hose due to over flexing.
Distributed By:
CORPORATION
800 Woodlands Parkway
Vernon Hills, IL 60061
12/11