SUN PROTECTION FILM
Transcription
SUN PROTECTION FILM
1 1 SUN PROTECTION FILM static cling technology - no adhesive required Directions for use • Read the instructions carefully before installation! • You will also need: window cleaner, tape measure, cutter, ruler, spray bottle, (paper-)towel. 1 1 2 Measure. Measure your window. Most important is the surface inside the rubber seal or the window frame. It is recommended to leave a space of 2 mm between the film and the window frame. 3 Cut. Lay the film on a clean, smooth surface (not on a carpet because of static charging). Cut the 1 a ruler and a cutter to the desired measufilm using rement. Note: The sun protection film has a slight yellowish tint! In order to prevent scratches it is 1 with transparent protection film on both provided sides. These are clearly thinner than the sun protection film and completely transparent. 4 GB 05/2014 Clean the window. Clean your window using a commercially available glass cleaner. A completely clean window surface is a prerequisite for the successful application of the sun protection film. Spray the window. Mix a few drops of washing up liquid with cold water in a spray bottle. Spray the window (interior side) generously with the mixture. The generous use of this mixture allows for easy positioning of the sun protection film on the window. Note: The use of water is essential for adhesion of the film! 5 Remove the first protective film. Pull the protective film, which is found in a rolled-up state on the inside, off the sun protection film. Start in a corner to do this. Immediately after pulling off the transparent protective film, apply the sun protection film to the window. Separate the sun protection film gently, to prevent it from coming into contact with itself. Note: be sure to protect the sun protection film from dust and lint once you have removed the protective film! 6 Apply the sun protection film. Place the side of the sun protection film from which you have removed the protective film onto the wet window (interior side). After you have generously pre-sprayed the window with the mixture, the film can be easily moved into the correct position. If this is not possible, remove the film and re-spray the window generously. Warning: do not use adhesive with the sun protection film! The film adheres statically without adhesive! Download. D 7 Spray the film surface. After you have positioned the sun protection film, spray the front side of the film with water. This is necessary in order to facilitate the next step and to avoid damaging the film. 8 Squeeze out the water. Now completely remove the water between the window and the film using the provided rubber squeegee starting from the inside and working towards the edges. Use a soft cotton cloth to remove traces of water and the squeezed-out moisture. Note: ensure a careful working of the edges. The edges and corners of the sun protection film should not have any contact with the rubber seal or window frame. Otherwise this could have a negative effect on the adhesion of the film to the window. 9 Remove the second protective film. Now that the sun protection film has been applied to the window, the second protective film can be removed. To do this, loosen the film which is still on the sun protection film starting at one corner and remove it carefully and completely from the sun protection film. GB I F CZ ES NL RO HU www.d-c-fix.com NOTES • The transparency of the film will improve after 2 – 3 days, once the water residues between the film and the widow have evaporated. • Only use the film on the interior side of the window. • Many window manufacturer’s guarantees become void once film is applied to the window. Window film does not break glass. However, it can make an already existing defect visible or accelerate its course. Cases of glass breakage are very rare. • The sun protection film adheres exclusively to clean, smooth glass surfaces. The film does not stick to satin finish or textured glass surfaces. • In order to ensure a successful installation do not apply the sun protection film to heated window surfaces. • With film applications onto larger windows we recommend using the help of a second person. • When measuring and cutting the film, use the product’s existing edges and corners wherever possible. • Always move from the centre towards the edges when using the squeegee to squeeze out moisture. • By putting multiple sheets together you can service any window size. • Cleaning: The foil can be cleaned using commercially available window cleaners. Do not use any cleaning products with a high alcohol or spirit content! d-c-fix® is a trademark of Konrad Hornschuch AG Salinenstraße 1 74679 Weißbach GERMANY www.d-c-fix.com