SLR5 SLR7 Pub 11-05 Rev 02-06

SLR5 & SLR 7
STRAIGHT LINE RIPPER
Rev 02/06
Part No. 4935P
PART'S MANUAL
An Operator's Manual was shipped with the equipment in the
Manual Canister. This Operator's Manual is an integral part of
the safe operation of this machine and must be maintained
with the unit at all times. READ, UNDERSTAND, and FOLLOW
the Safety and Operation Instructions contained in this manual
before operating the equipment. If the Operator's Manual is
not with the equipment, contact your dealer or M&W
(800-446-5158) to obtain a Free copy before operating the
equipment.
M&W ®
1020 South Sangamon Ave.
Gibson City, Illinois 60936
217-784-4261
© 2006 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic
machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts
and quantities required.
2. The Purchase Order must include the name and address of the person or organization ordering
the parts, who should be charged, and if possible, the serial number of the machine for which the
parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number, and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and are
subject to special handling. Request a quotation for such parts before sending a Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE:
Please refer to The Safety Section in the front of this Manual for the proper Part
Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use
genuine Alamo Group Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death. Direct
any questions regarding parts to:
M&W
1020 South Sangamon Ave.
Gibson City, Illinois 60936
217-784-4561
©2005 Alamo Group Inc.
Parts Section – 2
PART NAME INDEX
AUTOMATIC RESET SHANK ................................................................................................................................................ 8
AUTOMATIC RESET STRAIGHT SHANK ............................................................................................................................. 6
COULTER UNIT ASSEMBLY Rev 02-06 ............................................................................................................................. 16
FOAM FILLED USED AIRCRAFT TIRE Pub 11-05............................................................................................................. 15
GAUGE WHEEL ASSEMBLY - PULL TYPE Rev 02-06...................................................................................................... 12
GAUGE WHEEL ASSEMBLY -3PT.LIFT Pub 11-05 ........................................................................................................... 10
HUB & SPINDLE ASSEMBLY Rev 02-06 ............................................................................................................................ 14
LIGHT KIT (SLR7 ONLY) Rev 02-06 ................................................................................................................................... 18
SHEAR BOLT SHANK ASSEMBLY ....................................................................................................................................... 5
TONGUE PULL TYPE ASSEMBLY Rev 02-06.................................................................................................................... 20
WING AND FRAME ASSEMBLY ........................................................................................................................................... 4
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 3
WING AND FRAME ASSEMBLY
ITEM
PART NO.
SLR5 QTY
SLR7 QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
02045000
00010300
33007C
3830218
3834854
00725708
3830251
3830252
2196
2450276
2450263
15B1800
2
2
2
1
1
2
1
4
16
16
16
2
2
2
1
1
2
1
2
4
BOLT
LOCKWASHER
HEX NUT
HITCH PIN
SPACER
SNAPPER PIN
CAT II PIN
CAT III PIN
CLIP PIN
MAINFRAME
END WING
FLATWASHER
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 4
SHEAR BOLT SHANK ASSEMBLY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
2450276
2450264
2450269
2456503
2451581
2450277
2450127
2450278
2450128
2454867
702316C
317017H5C
35009C
00000200
00009500
318012H5C
5JRC1490
316016C
00001400
00695100
02027400
32905C
02788400
00001800
2452520
2450135
1
1
1
1
1
1
1
1
1
1
2
4
6
6
2
1
1
1
2
1
1
1
1
1
2
*
BAR FRAME
SHANK
CHISEL POINT
SHANK PROTECTOR
SPACER BAR
MOUNT, UPPER RH SHANK
MOUNT, LOWER RH SHANK
MOUNT, UPPER LH SHANK
MOUNT, LOWER LH SHANK
BUSHING
WASHER
BOLT
LOCKWASHER
NUT
BOLT
BOLT
TOPLOCK NUT
BOLT
FLATWASHER
TOPLOCK NUT
BOLT
LOCKNUT
BOLT
TOPLOCK NUT
BUSHING, SHEAR BOLT
SHANK & POINT ASSY. (INCLUDES ITEMS #2-4, 21-24)
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 5
AUTOMATIC RESET STRAIGHT SHANK
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 6
AUTOMATIC RESET STRAIGHT SHANK
ITEM
PART NO.
QTY.
DESCRIPTION
1
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
2420232
02880900
35009C
00000200
2430261
2430262
49053
15B1400
2432543
2430334
2450269
2430275
2450285
2438404
331212C
2432523
420916
420619
2435508
2435507
2431106
00011700
31102H5C
331210C
2430265
2437424
2435509
2430320
300516H5C
2432521
45053
45051
2432301
2432300
15B1600
2434866
2431460
2431602
31103C
00002700
6D9016
2438332
02027400
00001800
32905C
02788400
2456503
2450134
2450133
1
4
4
4
1
1
4
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
1
5
2
4
2
2
1
1
2
2
2
1
1
1
1
1
1
SHANK MOUNT
BOLT
LOCKWASHER
NUT
PIVOT PIN
PULL ARM PIN
COTTER PIN
FLATWASHER
SPRING YOKE
PULL ARM
CHISEL POINT
PULL ARM TO MOUNT PIN
AUTOMATIC SHANK
SHANK WASHER
NYLON INSERT JAM NUT
PIVOT PIN
ROLL PIN
ROLL PIN
OUTER TOGGLE
INNER TOGGLE
STOP
LOCKWASHER
BOLT
NYLON INSERT JAM LOCKNUT
SPRING GUIDE BAR
SPRING
SPRING INSERT, END PLUG
SPRING TUBE
TAP BOLT
TOGGLE PIN
GREASE FITTING
GREASE FITTING
TOGGLE WASHER
PULL ARM WASHER
FLATWASHER
ROLLER
FLANGE CLAMP
TIE PLATE
BOLT
FLATWASHER
WHIZLOCK NUT
DECAL, GREASE, 8 HOUR
BOLT
TOP LOCKNUT
LOCKNUT
BOLT
SHANK PROTECTOR
STRAIGHT SHANK ASSEMBLY, COMPLETE
SHANK & POINT ASSEMBLY (INCLUDES ITEMS 14,16 & 48-52)
(TWO-PIECE CLAMP MOUNT
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 7
AUTOMATIC RESET SHANK
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 8
AUTOMATIC RESET SHANK
ITEM
PART NO.
QTY.
DESCRIPTION
1
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
2420232
02880900
35009C
00000200
2430261
2430262
49053
15B1400
2432543
2430334
2410400
2430275
2438360
2438404
331212C
2432523
420916
420619
2435508
2435507
2431106
00011700
31102H5C
331210C
2430265
2437424
2435509
2430320
300516H5C
2432521
45053
45051
2432301
2432300
15B1600
2434866
2431460
2431602
31103C
00002700
6D9016
2438332
2418402
2420161
2430179
1
4
4
4
1
1
4
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
1
5
2
4
2
2
1
1
2
2
2
1
1
SHANK MOUNT
BOLT
LOCKWASHER
NUT
PIVOT PIN
PULL ARM PIN
COTTER PIN
FLATWASHER
SPRING YOKE
PULL ARM
CHISEL POINT & PIN
PULL ARM TO MOUNT PIN
AUTOMATIC SHANK
SHANK WASHER
NYLON INSERT JAM NUT
PIVOT PIN
ROLL PIN
ROLL PIN
OUTER TOGGLE
INNER TOGGLE
STOP
LOCKWASHER
BOLT
NYLON INSERT JAM LOCKNUT
SPRING GUIDE BAR
SPRING
SPRING INSERT, END PLUG
SPRING TUBE
TAP BOLT
TOGGLE PIN
GREASE FITTING
GREASE FITTING
TOGGLE WASHER
PULL ARM WASHER
FLATWASHER
ROLLER
FLANGE CLAMP
TIE PLATE
BOLT
FLATWASHER
WHIZLOCK NUT
DECAL, GREASE, 8 HOUR
PIN, OVERSIZED
STRAIGHT SHANK ASSEMBLY, COMPLETE
SHANK, POINT & PIN ASSEMBLY (INCLUDES ITEMS 14 & 16)
(TWO-PIECE CLAMP MOUNT
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 9
GAUGE WHEEL ASSEMBLY -3PT.LIFT Pub 11-05
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 10
GAUGE WHEEL ASSEMBLY -3PT.LIFT Pub 11-05
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
2450276
2450268
2450267
2450290
2422503
2458409
35009C
00000200
00010600
00015800
2452517
49208
00751969
0536801
0536009
0536008
0538400
00750614
0530178
0536002
0536003
00002701
5DR12160
49033
0536700
TR416
2427601
2427800
2420102
0530113
1
2
2
2
2
4
8
8
2
6
2
2
4
2
2
2
12
12
2
2
2
2
2
2
2
2
2
2
*
*
BAR FRAME
GAUGE WHEEL MOUNT
GAUGE WHEEL TUBE
JACK
SPINDLE
U-BOLT
LOCKWASHER
NUT
BOLT
TOPLOCK NUT
PIN
HAIRPIN COTTER
BOLT
SEAL
BEARING CONE
BEARING CUP
DRIVE STUD
STUD NUT
HUB W/CUPS
BEARING CUP
BEARING CONE
FLATWASHER
SLOTTED NUT
COTTER PIN
HUB CAP
VALVE STEM
RIM
TIRE
HUB AND SPINDLE ASSEMBLY (CONSISTS OF #5, & 15-26)
HUB ASSEMBLY (CONSISTS OF #15,22, & 26)
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 11
GAUGE WHEEL ASSEMBLY - PULL TYPE Rev 02-06
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 12
GAUGE WHEEL ASSEMBLY - PULL TYPE Rev 02-06
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
2450276
2450268
2450267
2450290
00774821
2458409
35009C
00000200
00010600
00015800
2452517
49208
00751969
02957044
00750434
00756577
13198
00750614
00756489
00766576
0371242102
00756493
00756490
00026200
00756492
00766911
00003500
00775616
1
2
2
2
2
4
8
8
2
6
2
2
4
2
2
2
10
10
2
2
2
2
2
2
2
2
2
*
BAR FRAME
GAUGE WHEEL MOUNT
GAUGE WHEEL TUBE
JACK
SPINDLE
U-BOLT
LOCKWASHER
NUT
BOLT
TOPLOCK NUT
PIN
HAIRPIN COTTER
BOLT
SEAL
BEARING CONE -INNER
BEARING CUP -INNER
DRIVE STUD
STUD NUT
HUB W/CUPS
BEARING CUP -OUTER
BEARING CONE -OUTER
WASHER
SLOTTED NUT, THIN 1"NF PLC
COTTER PIN, 5/32 X 1-1/2
CAP,DUST
TIRE & WHEEL (FOAM FILLED)
GREASE FITTING
HUB AND SPINDLE ASSEMBLY (CONSISTS OF #5, & 15-26, & 28)
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 13
HUB & SPINDLE ASSEMBLY Rev 02-06
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00775616
00774821
00756576
00750434
00756577
13198
00750614
00756490
02957044
00756493
00756492
00026200
00003500
00756489
0371242102
1
1*
1
1*
5
5
1
1
1
1
1
1*
1*
1
ASY SPINDLE
SPINDLE SINGLE WHEEL
BEARING CUP OUTSIDE
BEARING CONE INSIDE
BEARING CUP INSIDE
BOLT, HUB
NUT 1/2-20NF 90DEG.CONE LUG PL
NUT SLOTTED THIN 1 NF PLC
OIL SEAL HEAVY DUTY - TK-15
WASHER
DUST CAP
PIN-COTTER 5/32 X 1-1/2
ZERK FITTING 1/8 STRAIGHT
HUB W/ CUPS Y STUDS
BEARING CONE
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 14
FOAM FILLED USED AIRCRAFT TIRE Pub 11-05
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
00766911
00766911A
-
ASY,AIRCRAFT TIRE & WHEEL (CURRENT)
ASY,AIRCRAFT TIRE & WHEEL (ALTERNATE)
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 15
COULTER UNIT ASSEMBLY Rev 02-06
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 16
COULTER UNIT ASSEMBLY Rev 02-06
ITEM
PART NO.
SLR5 QTY
SLR7 QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
2450276
2451355
2451070
2450282
2451582
2417515
2417514
2416775
2417422
2417513
32908C
2417517
2458352
2458407
421011
00001300
00001200
3905A3C
2457508
42109
1438442
49054
2417516
49024
6W702
0536003
0536002
02886900
2417506
2418401
33097C
0536700
2450298
1830202
1832500
F101
1
5
4
1
5
5
5
5
5
5
5
5
5
10
5
40
40
5
5
5
5
5
5
10
5
10
10
20
5
5
5
5
2
2
2
2
1
7
6
1
7
7
7
7
7
7
7
7
7
14
7
56
56
7
7
7
7
7
7
14
7
14
14
28
7
7
7
7
2
2
2
2
BAR FRAME
BOLT PLATE
MOUNT PLATE
CENTER MOUNT PLATE
COULTER ROD
SPRING ROD
COULTER PIVOT
SPRING SPACER
SPRING
SPRING BUSHING
LOCKNUT
SINGLE ARM
SMOOTH BLADE, 22"
U-BOLT
ROLL PIN
LOCKWASHER
NUT
SETSCREW
LOCKING COLLAR
ROLL PIN
BUSHING
COTTER PIN
ROD PIN
COTTER PIN
SEAL
BEARING CONE
BEARING CUP (IN ITEM #29)
CARRIAGE BOLT
HUB W/CUBS
RETAINER WASHER
SLOTTED NUT
HUB CAP
JACK STAND MOUNT - 3PT LIFT UNITS ONLY
STAND WELDMENT - 3PT LIFT UNITS ONLY
STAND PIN - 3PT LIFT UNITS ONLY
KLICK PIN 3/16 - 3PT LIFT UNITS ONLY
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 17
LIGHT KIT (SLR7 ONLY) Rev 02-06
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 18
LIGHT KIT (SLR7 ONLY) Rev 02-06
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
12A
13
14
15
16
17
18
19
2431606
2431607
00015800
00011400
02816800
370013C
33105C
1458398
1458392
2467901
2467900
2457900
1457939
2467903
2467902
2467904
3263N13C
329023C
3263N6C
5E805
4
4
24
24
4
4
4
4
4
2
2
1
1
1
1
2
4
6
2
12
LIGHT BRACKET
UPRIGHT BRACKET
LOCKNUT
BOLT
NUT
LOCKWASHER
NUT
ORANGE REFLECTOR
RED REFLECTOR
DUAL SIGNAL LAMP, RED/BLACK
DUAL SIGNAL LAMP, AMBER/AMBER
MAIN WIRING HARNESS -10’ -3PT LIFT UNIT
HARNESS,MAIN WIRING - 20’ -P/T UNIT
PLUG HOLDER
WISHBONE HARNESS
EXTENSION HARNESS
SCREW
LOCKNUT
SCREW
TY-RAP (NOT SHOWN)
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 19
TONGUE PULL TYPE ASSEMBLY Rev 02-06
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 20
TONGUE PULL TYPE ASSEMBLY Rev 02-06
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
2465500
2460244
330812C
165020
2466250
1338600
2451606
2451155
00007000
00015800
00749130
00001300
00001200
2450309
00749185
2196
2450302
2450303
3830252
1450115A
02957009
00015800
2450304
3830218
00725708
2450310
2450306
2450305
1831446
00037200
2451452
020014200
00001800
2450307
2450308
2458409
15B1800
2457103
02962213
2457351
00770346
0276600
00024100
02959924
1457939
00726768
02042400
00761202
02971020
2437107
02837800
2467200
02899900
2458411
00766911
2471001
00725712
00775616
00751969
00015800
2737101
1
1
1
1
1
1
1
1
2
2
4
4
4
1
2
2
1
1
1
4
4
4
2
2
2
2
1
1
4
16
2
4
4
2
2
4
4
2
4
1
3
2
2
2
1
4
2
1
1
1
1
2
1
2
2
2
2
2
2
2
2
HITCH
WDMT,HITCH PIN
HEX SLOTTED NUT 1 1/4-7
PIN, COTTER 5/16 X 2-1/2 PL
CHAIN,SAFETY TOW,16,000 LB CAP
JACK STAND-5000#
PLATE, HOSE RETAINER
CLAMP, HOSE
BOLT 3/8NC X 1-3/4 PL5
NUT,TOPLOCK 3/8NC PLB
HHCS 1/2-13UNC 1-3/4 PL5
LOCKWASHER 1/2 PL STD
NUT,HEX 1/2 NC PL
WDMT, TOP LINK LOWER PIN
FLATWASHER 1-1/4 STD
CLIP (LYNCH PIN), 13/32 DIA.
WDMT, TONGUE
WDMT, TOP LINK
WDMT,CAT III TOP LINK PIN
ASY,HUB & SPINDLE
HHCS 3/8 NC 3-1/2 PL5
NUT,TOPLOCK 3/8NC PLB
WDMT, WHEEL STRUT
WDMT,LOWER CAT 3 PIN
PIN 3/8 X 1-3/4 SNAPPER
WDMT, WHEEL STRUT PIVOT PIN
WDMT, LEFT STRUT SUPPORT
WDMT, RIGHT STRUT SUPPORT
U BOLT 3/4-10 X 5.5 X 4.06
NUT TOPLOCK 3/4 NC PLC
BAR, STRUT SUPPORT REAR CLAMP
BOLT, 1/2NC X 6
LOCKNUT TLM 1/2 NC PLB
WDMT, REAR STAND
WDMT, REAR STAND SUPPORT
U-BOLT,3/4-10 X 7-3/4 X 4-1/32
WASHER 1-1/8 SAE PLAIN
CYLINDER,HYDRAULIC 3 X 10
ADAPTER, HYD, ELBOW
VALVE, HYDRAULIC FLOW DIVIDER
ADAPTER, HYD, STGHT
BOLT, HEXH 1/4NC 1-3/4
FLATWASHER STD 1/4 PL
NUT TOPLOCK 1/4 NC PLB
HARNESS,MAIN WIRING - 20
ASY,MOUNTED STUBBLE GUARD TIRE
ADAPTER, HYD, STGHT
HOSE #8 - 8FJX - 8FJX -156LG
HOSE #8 - 8FJX - 8FJX -202LG
UNION TEE, 1/2 TUBE
HOSE #8 - 8JFX - 8FJX - 60LG
HOSE #8 - 8FJX - 8FJX - 90LG
HOSE #8 - 8FJX - 8FJX -120LG
PIN REAR STAND W/"R" CLIP
USE FOR PARTS ONLY
STOP,CYLINDER - 3 X 8
PIN PULL BENT 1/2 X 3 WITH
ASY SPINDLE
HHCS 3/8 NC 3-1/4 PL5
NUT,TOPLOCK 3/8NC PLB
STOP RING SET-1 1/8 & 1 1/4
SLR5 & SLR7 (Nov-05) -Current Rev 02-06
©2006 Alamo Group Inc.
Parts Section – 21
M&W
LIMITED
WARRANTY
1. LIMITED WARRANTIES
1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
M&W Implement Model _____________________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
M&W
An Alamo Group Company
1020 South Sangamon Ave.
Gibson City, Illinois 60936
217-784-4261
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1.
2.
3.
4.
Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and
Ensure that each employee uses such Seatbelt while the tractor is moving; and
Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seatbelt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going - especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly - no jerky turns, starts, or stops.
Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...
Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.
SLR5 & SLR7 PL 11/05
Printed U.S.A.
P/N 4935P