Züllig Transmitter

Comments

Transcription

Züllig Transmitter
Züllig Transmitter
Example:
Controlling waste water treatment with
one TSS sensor and three D.O. sensors.
The s-line transmitter is compatible with all digital Züllig probes. The signals
from four probes can be processed at the same time.
Advantages of s-line
• Up to four seperate measurements with one transmitter
• Easy operation
• Individually configurable
• Up to four measuring values
can be displayed
• Four analog outputs
• Automatically set up to the
connected probe. Sensor
specific data are stored in the
probe
• Noise-insensitive
Technical Highlights
Variable display design
Up to four measuring values can be displayed at the LED. Other measurement
values can be scrolled or leafed through on the main menu with the turning knob.
Combinations of Smart Sensors with s-line
Parameter
Probe type
Dissolved Oxygen, Temperature
Dissolved Oxygen, Temperature
Dissolved Oxygen, Temperature
Dissolved Oxygen, Temperature
Turbidity, Suspended Solids
Turbidity
pH-Value
pH-Value, Temperature
Redox
Conductivity, Temperature
Level, Volume, Flow
S14-S
S15-S-25
ODO
OH-S-25EX
COSMOS®-25, COSMOS® EX
TML-25
PH1-S-25
PH2-S-25EX
RX-S-25EX
LF-S-25
HT-68, LT-68
EX
Load in %
100
80
30
10
30
20
10
10
10
40
20
= Is valid also for version EX for Zone Ex 1
Different probes burden the probe connection differently. The total load of the
connected probes at each of the 2 probe connections (connection 1 and connection 2) may not exceed 100%.
Characteristics
„ Plug and Play
„ All sensor-specific data are
automatically read into the
transmitter
„ Digital data transfer by one
signal cable only
„ Two additional analog outputs
available
„ Compact design for panels or
stand-alone use
„ Profibus communication
„ Plug-in connector
Lowering cost of ownership
• Up to four Smart Probes can be
connected with one transmitter
• Simplified start-up by easier
installation using Smart Probes
(integrated microprocessor)
• Low installation costs due to
multiple cable routings
• Usage of cost-efficient standard
cable
• User-defined combination of
individual probes
Type of construction
Technical Data
Sensorbus . . . . . . . . . . . . . . . . . . . .
Analog inputs . . . . . . . . . . . . . . . . .
Analog outputs . . . . . . . . . . . . . . . .
Relay outputs . . . . . . . . . . . . . . . . .
Power supply voltage . . . . . . . . . . .
Interfaces (option) . . . . . . . . . . . . . .
Protection class . . . . . . . . . . . . . . .
Temperature range . . . . . . . . . . . . .
Enclosure . . . . . . . . . . . . . . . . . . . .
up to 4 Smart Sensors
2 current signals 0/4…20 mA
4 current outputs 0/4…20 mA
4 potential free contact for twoway two-step controller or
alarm/counter
90…264 VAC, 50/60 Hz or
18…36 VDC (optional)
Profibus-DP Slave
2
s-line E, 0…50 °C
s-line V, -20…50 °C (AC version
with heating)
Type E (panel version) IP50
Type V (field version) IP66
1441e02 21/02/2008
Subject to technical changes
Instrumentation for Water
and Waste Water Control
Type V (outdoor) and Type E (mounting)
Headquarter in Switzerland:
Züllig AG
CH-9424 Rheineck/Switzerland
Phone +41(0)71 886 91 11
Telefax +41(0)71 886 91 66
www.zuellig.ch
Representatives worldwide