PRICE WHOLESALE REV 31 PRICE 7-9-14Fin - Smart

Transcription

All Products Catalogue and Price List
PRICE LIST MAINTENANCE
All PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. IT IS THEREFORE
RECOMMENDED TO OBTAIN PRICE CONFIRMATION PRIOR
TO MAKING SALES COMMITTMENTS. CONTACT [email protected]
OR PHONE SMART-CALLER SALES DEPARTMENT ON 03 9588 0833.
NEED SOME HELP?
We offer a free of charge project design and costing service.
Provide us with adequate information including site drawings
and we will specify, design and cost the project for you.
Issue date: 01/09/2014 / Revision No.: 31
Part A - EMERGENCY-CALL TELEPHONE PROUDUCTS & ACCESSORIES
1. ANALOGUE EMERGENCY–CALL TELEPHONES & DIALLERS (Excluding Accessories) [GST Exempt]
Item
1.1
Model
P-HP4-DOMESTIC
(Family monitoring
version of the Blue
phone)
See Wireless
Accessories in
Section 11. Other
Accessories in
Sections 5, 7,13 & 36
Description
Domestic version Blue-Phone, including Pendant
This model includes voice annunciation and is delivered with a special code that
limits it operation to domestic “family caring” applications where it will communicate
voice to voice with up to 8 destinations the last of which can be the 000 Emergency
Service if preferred.
If using the Emergency 000 Service it is important to use a certain format in the
outgoing announcement. This information is included in the handbook.
This domestic model can be remotely upgraded to a fully featured HP3-BP-01
version to allow full professional monitoring for an additional fee as detailed in item
1.15 (PROF-UPGRADE)
It includes plug-pack, line cord, handbook and one pendant.
Page 1
Image
W/Sale $
RSP $
$298.00
398.00
1.2
P-HP4-01
(Emergency Blue
Phone)
Professional Blue-Phone including Pendant
This professional model includes voice annunciation, Talking Clock, Ademco
professional monitoring plus voice-to-voice monitoring which can include the family
mode monitoring if required for some or all events. It also includes a highly featured
home security facility and will accommodate a wide range of useful accessories..
1-99=298
100+=275
200+=270
398
348
340
323
448
225
298
See Wireless
Accessories in
Section 11. Other
Includes plug-pack, line cord, handbook and one pendant. See Multicode-09 for hardAccessories in
wired inputs.
Sections 5, 7, 13 & 36
1.3
P-HP3-BP-04-STR
(Includes strobe
transmitter)
As item 1.2 but with strobe transmitter- Including pendant
Normal HP3 Blue-Phone professional version but with a 304Mhz transmitter to trigger
wireless activated strobes or similar devices. See Multicode-09 for hard-wired inputs.
See RDU-304-01 Receiver in Section 12 for controlling the optional Strobe
transmitter facility. A suitable Strobe can be found in Section 36.
1.4
P-HD4-DOMESTIC
(Analogue Dialler)
See Wireless
Accessories in
Section 11. Other
Accessories in
Sections 5, 7, 13 & 36
Smart Dialler Domestic including pendant
This model includes voice annunciation and is delivered with a special code that
limits it operation to domestic “family caring” applications where it will communicate
voice to voice with up to 8 destinations.
It will not communicate with on-site or community based professional monitoring
centers (unless upgraded) but is approved to communicate with 000 EmergencyServices subject to being a last resort contact and subject to using a certain format in
the outgoing announcement.
This domestic model can be remotely upgraded to a fully featured HD4-01 version to
allow full professional monitoring for the cost of a service fee.
It includes plug-pack, line cord, handbook and one pendant. See Multicode-09 for
hard-wired inputs.
Page 2
Domestic Model
1.5
P-HD4-DIALER-01
(Analogue Dialler)
(Professional
Versions
See Wireless
Accessories in
Section 11. Other
Accessories in
Sections 5, 7, 13 & 36
HD4 Under phone/Desk or Wall mount Emergency Call Dialler – Including
pendant
This model differs from its competition in almost every aspect. One significant
difference is its aesthetic design, which makes it ideally suited to wall or desk
mounting in addition to the traditional under phone placement if required. It uses the
highly developed and proven circuit and firmware of the HP3/Blue-Phone analogue
telephone with top mounted speaker for maximum quality voice communication.
It includes the same HP3 Phone version 48 wireless inputs, 8 destinations and home
security facilities etc. Programming is made easy by the use of the adjacent normal
telephone keypad and comprehensive remote programming is also possible. See
Multicode-09 for hard-wired inputs.
Includes plug-pack, handbook, line cord and single pendant. See Accessories for
wall-mount bracket.
Page 3
Professional Model
225
298
2. IP, V0IP, GSM & GPRS EMERGENCY–CALL TELEPHONE PRODUCTS (Excluding Accessories)[GST Exempt]
Item
2.1
Model
P-HP4-02 -GSM
(Standard
Professional Model
with GSM redundancy
DEVELOPMENT
Description
Professional Analogue phone including Pendant but with GSM back-up option
(Less SIM card)
A standard analogue PERS unit which includes voice annunciation, Talking Clock,
Ademco professional monitoring plus voice-to-voice monitoring. It includes a GSM
module that takes over in the event of no communication via the PSTN/PABX or ATA
connection to a Broadband service. It reverts to normal PSTN/PAB/ATA operation on
resumption of such interrupted services.
Image
W/Sale $
RSP $
TBA
TBA
TBA
TBA
TBA
TBA
Includes plug-pack, line cord, handbook and one pendant. SIM card not included, to
be supplied by service provider.
2.2
P-HP4+ WIRELESS
(Standard
Professional Model
with wireless overlay
redundancy)
DEVELOPMENT
Professional Blue-Phone including Pendant but with Wireless transmitter backup
Ademco professional monitoring string plus voice-to-voice monitoring.
It includes a high power 1W 915Mhz wireless transmitter module that will duplicate all
call and cancel traffic to the head-end equipment which in turn displays the caller
details to local display devices (such as pagers or similar) and/or delivers an
appropriate ADEMCO string to a central monitoring company if site wide dialler also
selected.
It may be programmed to always send the wireless call or to do so only on failure of
the PSTN/PABX or ATA IP communication path. In the latter mode it reverts to
normal PSTN/PABX/ATA operation on resumption of such interrupted services. An
optional UHF antenna with coaxial cable is available to accommodate any ‘fringe
area’ PERS units.
2.3
P-HD4+GSM
(Standard
Professional Model
Dialler with GSM
redundancy)
DEVELOPMENT
Professional Analogue Dialler including Pendant but with GSM back-up option
(Less SIM card)
Ademco professional monitoring plus voice-to-voice monitoring. It includes a GSM
module that takes over in the event of no communication via the PSTN/PABX or ATA
connection to a Broadband service. It reverts to normal PSTN/PAB/ATA operation on
resumption of such interrupted services.
Includes plug-pack, line cord, handbook and one pendant. SIM card not included, to
be supplied by service provider.
Page 4
2.4
P-GSM-FWT-01
(GSM back-up
terminal)
NEW ITEM
GSM Fixed Wireless Terminal
This product can be placed between any Smart-Caller PERS telephone and the
normal wall socket and in the event of the normal PABX/PSTN/ATA analogue
connection being disabled and/or the Internet Service being unable to deliver the call,
this device will automatically take over the both-way data and voice communication
path to allow emergency-call (and normal call) services to continue as normal. Using
hand-o0ver/hand-back sensing the phone will return to its normal communication
path on resumption of dial tone from its PABX/PSTN/ATA connection.
POA
POA
POA
POA
POA
POA
98
165
GST Exempt
An ideal back-up facility for NBN FTTP connections where power and service
continuity is not assured. SIM card not included.
2.5
2.6
P-CARELINE-IP
(An IP only PERS
unit)
Professional IP (only) PERS Dialler including Pendant
For those that have total confidence in uninterrupted IP availability then this unit
offers the best and most economical solution.
DEVELOPMENT
Like the other CARELINE alternatives it offers up to 16 wireless inputs along with
hard-wired options. See datasheets for more information.
P-CARELINE IP+G
(An IP plus GSM
PERS Unit)
Professional IP + GSM PERS Dialler including Pendant
As above but including the GSM back-up capability.
Like the other CARELINE alternatives it offers up to 16 wireless inputs along with
hard-wired options. See datasheets for more information. A Bluetooth adaptor allows
vital sign monitoring for ‘e’health in home health management applications.
DEVELOPMENT
2.7
M-V3G-MED
V3G Mini SOS Medical speech Pendant
Has no keypad or touch screen. Program the contacts list though your computer and
add photo IDs as well. Pressing the SOS button will text to up to 5 contacts to notify
the user requires help. A link will also be text with thier GPS co-ordiantes. At anytime
you can text "find" and the GPS co-ordinates will be text back to you. TXT "pickup"
then call into the V3G and it will answer your call in loud speaker mode. Fantastic as
an emergency call pendant, always be incontact with 2 way voice contact and gives
you control of who can be contacted.
Requires to be outdoors for GPS positioning to work reliably and requires a SIM
Battery life up to 7 days Measures 77x45x15
Page 5
As above
2.8
2.9
M-V3G-OH&S
V3G Mini SOS Medical Speech Pendant
Has no keypad or touch screen. Program the contacts list though your computer and
(Commercial version add photo IDs as well. Pressing the SOS button will text to up to 5 contacts to notify
of V3G for non
the user requires help. A link will also be text with GPS co-ordinants. At anytime you
medical applications). can text "find" and the GPS co-ordinates will be text back to you. TXT "pickup" then
call into the V3G and it will answer your call in loud speaker mode. Fantastic as an
emergency call pendant, always be incontact with 2 way voice contact and gives you
control of who can be contacted.
Requires to be outdoors for GPS positioning to work reliably and requires a SIM
Battery life up to 7 days Measures 77x45x15
GPS/GPRS Tracker and two way communications unit
Irrespective of the application being a Farmer working his tracker in the field or an
aged resident having absconded from safe perimeter containment or perhaps a staff
(Personal tracker for member visiting domestic residents at night, this low cost personal tracking device
wandering Residents will identify the location of that person within approximately 15M. This is achieved by
use of a combination of GPS and GSM technologies. Has excelent GPS locating.
or Staff at risk)
98
165
plus GST
M-SAFELIFE -PET01
The tracker is effectively a mobile phone with inbuilt GPS satellite navigation
positioning capabilities. 2G Technoloy 3G available in 2015. Ask for brochure.
Page 6
140
198
GST Exempt GST Exempt
PART ‘B’. - RESIDENT SAFETY SENSOR PRODUCTS
Hard-Wired & Cordless (Wireless) ‘Safe Containment’ Aged Care Accessories
3 PERIMITER ‘SAFE CONTAINMENT’ PRODUCTS [GST Exempt & TGA Approved]
Item
3.1
3.2
3.4
Model
A-PSM-01
A-SL139
A-TX-02
Cura Pt No 2572
(Wanderer
Wrist/Ankle band
Transmitter)
System essential
item
Description
PULL STRING MONITOR
Detects when resident or patient falls or leaves a chair or bed. Connects to Nurse call
system (GCORD REQUIRED)
Crash mat
Emitting an alarm when patient/ resident falls from bed landing on mat sending alarm
through nurse call system (BME-03 and GCORD required)
Image
W/sale $
RSP $
65
94
248
354
115
162
Door-Alert Wanderer wrist/ankle band transmitter [Essential Part]
This small dimension waterproof wrist transmitter has a battery life of up to 10 years
in sleep mode. Once activated by use of a magnet this transmitter commences to
transmit each 400MSec (0.4 second) allowing active battery life of typically 12
months. It may also be deactivated via a magnet to allow storage. Battery supervision
and monitoring is also provided.
Each wrist transmitter has a slightly different transmit code thereby allowing individual
identification of the wanderer if used within a multi/door/multi person centralized
system or if using the optional TTest-01 Door tester unit. At sites where busy 433Mhz
wireless systems exist it is possible to use the 315Mhz alternative frequency.
Each transmitter is supplied with wrist/Ankle strap. See Spares & Accessories
(Section 37) for spare wrist bands and miscellaneous parts and spares
A wrist/ankle strap included with each transmitter. See Section 37 for details of
spare straps.
Page 7
3.5
A-CK-01 Caregiver
key
Cura Pt No 2642
(Useful cancel and
system reset key for
many applications)
3.6
3.7
Carer Magnetic key-ring Cancel Key (Recommended Part)
No Cura based system should be without a number of these inexpensive key-ring
magnets. They are used to activate or deactivate the wireless tags and to cancel
active alarms at the Door Alert strip sensor and similarly cancel alarms generated by
other various equipment items.
A-DMS-PP
(Cura Pt No T1215021)
12V 1500mA Plug Pack for DMS-02 Door Strip System
If you are not using battery backed nurse-call system power supply or other suitable
power sources at the door station it is recommended to use this high quality low EMI
performing power source.
A-TRX-02
Pt No 2575
Door-Alert Cancel transmitter (Optional part)
Although a Door Alert system alarm can be cancelled via many alternative methods,
one such method is for the carer/s to be wearing a wrist cancel transmitter.
(Carer’s Optional
Cancel transmitter)
12
17
35
52.5
112
163
33
55
Suggest purchase a few of these as they are used extensively as a low cost means
of resetting (cancelling) alarm conditions
Simply touch the correct location to switch on a resident’s wireless tag or to reset an
alarm in the strip or other sensor.
Cancel functions can also be achieved by touching a certain location on the sensor
strip with a small key-ring magnet or to place a Reset Button in a close-by location
generally out of reach and sight of residents.
See item 3.4 for a low cost alternative. Other alternatives are listed below.
3.8
N-CANCEL-SW-01
Pt No 5001
Reset/Cancel momentary action press button (Optional part)
This cancel button is primarily intended to cancel the local alarm condition (i.e. the
visual and audible alerts at the door station) however; in some hard-wired nurse-call
(Optional momentary systems it s connection between the door strip and the nurse-call system will also
contact reset button) cancel an active alarm call within the nurse-call system.
Note. See also Cancel button alternatives that suit Smart-Caller hard-wired and
wireless systems that will also provide Call, Staff Assist and Cancel
Page 8
3.9
A-PROTRAC-MINI
Includes Antenna
(Economy model
Requires
laptop/software)
Software program
and cable
$140
3.10
A-PROTRAC-MAXI
PROTRAC MINI - INCLUDING ANTENNA - Economy Model Wanderer Door
Station.
2 Relay - Closing contacts
If door locking is required the Protrac Maxi model is required.
This unit is programmed via a software program and is not user configurable without
software
690
900
963
1,251
207
269
Do not
duplicate cost
Do not duplicate
cost
54
90
Has 2 Inputs for door reed and alarm cancel
PROTRAC MAXI - INCLUDING ANTENNA - user configurable settings
This sytem is programmed by dip switch settings ( no software required)
Includes Antenna
larger system
configurable
without
laptop/software
3.11
A-PROTRACANTENNA
(Do not duplicate.
Alread included in
system price)
LED staus or Alarm
Door locking output optional as standard
Relays for momentary, latched and door locking outputs.
Power and relay status LEDs and input staus LEDS
LED Receive signal strength Indicator
6 Inputs - For door reed and alarm cancel + 4 more
Manual adjustment of receiver sensitivity (no software required)
Power requirements : 12 DV reticulated or power pack. Power pack not included.
ANTENNA
This highly directional antenna is square in shape and look similar to a piece of
Perspex. It is to be placed above the door either behind the plaster or ceiling tile or
directly on the plaster ceiling.
Comes with a 2 metre coax cable. It is preferable to keep the length of the coax
between the controller and the antenna as short as practical.
3.12
A-PROTRAC WRIST WRIST TRANSMITTER 433 Mhz
Lightweight, waterproof reusable tags complete with standard hospital ID wristbands
TAG
or use a wrist band of your choice. Battery life expectancey 3-5 years.
Page 9
3.12B A-PROTRAC WRIST Wrist Straps for above (Hospital type)
STRAPS
3.13
A-SL114
3
5
POA
435
POA
410
Call Alert Easy Press Pendant Cord Proffessional Home Kit
Operating on UHF frequency allows for range of up to 200 meters between
transmitter and pager. The pager is a proffesional model and allows the carer to
move about the home and property whilst being contactable at the press of a button.
Utilising Salcom Paging technoloy.
3.14
A-SL113
Call Alert Pendant Cord Proffessional Home Kit
Operating on UHF frequency allows for range of up to 200 meters between
transmitter and pager. The pager is a proffesional model and allows the carer to
move about the home and property whilst being contactable at the press of a button.
Utilising Salcom Paging technology
Page 10
4. FLOOR, BED AND CHAIR HARD-WIRED SAFE CONTAINMENT’ PRODUCTS [GST Exempt & TGA Approved]
Item
4.1
4.3
4.4
4.4A
4.5
Image
RSP $
Large Floor Pressure mat hard-wired with 6.3mm Plug
Designed to immediately alert that a person had exited the bed. It is a large (1200 x
600mm) pressure mat being warm underfoot. It is waterproof and washable using a
low profile, non-slip material. 12 month pro-rata warranty applies.
You may want to also purchase a ADAP-2, being a 6.3mm standard double adaptor.
Also available ADAP3 (triple) Adaptors See Section 17.
153
226
A-MAXI-MAT-01x8
(Bulk supply)
12 month pro-rata
warranty
As above but in single packs of 8 units per pack (1 year warranty)
Due to the cost and complexity of dispatch packing we recommend purchasing the 8pack standard stock package.
See BMS-01 and BME-01 universal bedside controllers below for domestic or other
situations where a nurse-call call-point is not applicable. Also see Sections 5 & 6 for
cordless alternatives to suit telephone/dialer and other cordless (wireless)
applications
999
1,428
A-BREAKCORDUSB
Pt 2480
Spare Maxi Mat Break Cord
The Maxi Mat cord has a weak Link Break Cord. If this cord becomes damaged you
can simply replace the Break Cord and not replace or service the mat.
25
30
A-MAXI-MAT-FM
FOLDABLE HARD-WIRED BED EXIT FLOOR MAT
This mat can be folded into 3 for easy storage and shipping.
It also has reinforced eyelets to allow it to be hung up for easy storage and cleaning.
Measures 119cm x 60cm. Comes complet with a double adaptor arrangement
allowing a bell press pendant cord to also be connected to the same nurse call point.
203
273
33
44
152
226
12 month pro-rata
warranty
4.2
Description
HARD-WIRED BED EXIT FLOOR SENSORS
W/Sale $
Model
A-MAXI-MAT-01
Pt No 2633
(Pressure Floor Mat)
For mat as above
A-BREAKCORD-FM Y CABLE FOR THE FOLDABLE FLOOR MAT
For foldable floor mat as above (MAXI-MAT-FM)
A-MAXI-MAT-01DEM
(Floor Mats and Bed
Exit PIRs)
Maximat with RJ45 connector for Demcon & Demrad floor connectionThe main
difference between the bed exit accessories in this section and those listed within the
hard-wired Dementia room systems is the rq1uirement for the sensors to connect
into a CONN-02 bedside connection plate having an RJ45 socket.
That socket also supplies 12v power to those devices that require a power source
SEE SECTION 21 FOR FULL DETAILS
Page 11
4.6
A-BPLB-01
Pt No 2626
(Within-bed Bed Exit
Sensor)
12 month pro-rata
warranty
HARD-WIRED BED & CHAIR EXIT SENSORS
Bed Exit Pressure Pad – hard-wired (1 year warranty)
This pressure sensitive bed exit sensor is usually placed under the Kylie mattress
protector at shoulder position. Because it is intended to detect the removal of
pressure it is necessary to operate in reverse to normal pressure mat devices
whereby removal of pressure generates the alarm condition.
Measuring 760mm x 510mm the low cost BPLB-01 pad is classified as a
consumable item having a 12 month life expectancy and warranty. 30 day and 3
month warranty versions also exist for use in infectious and palliative applications.
Contact Smart-Caller for further information.
82.5
121
58.3
88
The choice of the BMS-01, BME-01 or BMV-01 bedside control unit described below
is a necessary accessory. Also see Sections 5 & 6 for cordless (wireless versions)
4.7
A-BPSC-01
Pt No 2628
(Chair Exit pad)
12 month pro-rata
warranty
Chair Exit Pad – Hard-wired (1 Year Warranty)
Where a chair is in close proximity to a call-point this chair exit sensor can be hardwired to its BMS-01 or BME-01 controller listed below. It will trigger an alarm along
with audible tone in the event of the resident leaving or falling from the chair.
With wheel chairs it is more practical to use a wireless connection to the exit pad and
there are a number of scenarios that will allow a chair exit alarm to be identified along
with the location of the event. These options include teaching the chair pad
transmitter into the resident’s bedside call-point and/or teaching it into one or more
site-wide Safe-T-Net receivers.
Page 12
4.8
4.9
A-BME-03
Pt No 2611 0BS
Bed-Exit and Chair Exit Sensor Controller (Also suits Floor mat but not
normally required)
This low cost stand-alone bedside controller is an optional accessory for floor sensor
(Optional controller
use but is essential for a bed and chair exit sensors. This is because Bed and Chair
for floor mats but
exit sensors operate from an opening circuit rather than a closing circuit as
essential for bed and applicable to a floor pressure mat. It therefore requires power and has a plug-pack
chair sensor use.
socket and a battery compartment.
Includes on-off
With its reset button, programmable alarm delay adjustment and volume control for
switch)
the audible alert it also includes an adjustable time delay which is useful for limiting
false alarm calls with bed exit sensors. It also includes a socket for connection to the
bedside call-point and a plug-pack power socket.
Don’t forget
mounting bracket,
need a plug-pack?. Note. Select the appropriate wall or bed mounting bracket for this item and if
connecting to a nurse-call call-point you will need a 6.3mm male to male cord
See Section 37
(GCORD-1M) and you will probably need a double or triple adaptor in order to
connect multiple devices to the single call-point 6.3mm cord pendant socket. (See
both alternative models below and refer to list of bedside controller mounting
brackets and connection lead options in Sections 37 & 17 respectively.
A-BMS-01
Pt No 2607
(New alternative to
above model)
4.10
4.11
Enhanced Floor mat and Bed Exit sensor Controller
This model is as described above but with automatic rearm when the resident returns
to bed and it also allows the carer to reset the alarm using the magnetic key so that
the resident/patient is unable to reset the device.
It also includes a closing contact alerting facility with an RJ11 socket to allow
connection to the adjacent call-point.
Voice Bed Monitor Unit
Similar to the BMS-01 this model, in addition to providing tone alert as applicable to
the other models also provides the ability for a voice announcement. This would
typically be used with a family member voice to encourage the resident/patient to
(Floor, Bed & Chair
sensor controller with return to bed. In doing so this model like the BMS-01 non voice versions will
voice announcement) automatically reset should the resident return to bed.
It has alarm memory and both normally open and normally closed relay set for
additional flexibility in alerting and cancelling sensor incidents.
Don’t forget
Like the other controllers in the range it may be powered by plug-pack or battery
mounting bracket,
need a plug-pack? along with low battery reporting.
A-CBM/BME-PP
Power supply for all Cura 1 monitors
Power supply for all Cura 1 monitors
(Plug-Pack for Cura A high quality plug-pack to suit all Cura Monitoring units (as above)
Monitors)
68
99.5
65
99.5
99
146
15
20
As Above
A-BMVR-01
Pt No 2610
Page 13
5.
Item
5.1
CORDLESS FLOOR, BED & CHAIR SAFE CONTAINMENT’ PRODUCTS [GST Exempt & TGA Approved]
Model
A-MAXI-MAT-CL
Pt No 2624
(Cordless Pressure
Floor Mat to suit
transmitter insert)
12 month pro-rata
warranty
Description
CORDLESS FLOOR MAT MONITORS
Cordless Large Floor Pressure mat (less wireless transmitter (1 year Warranty)
This cordless product is designed to immediately alert that a person had exited the
bed. It is a large (1200 x 600mm) pressure mat being warm underfoot. It is
waterproof and washable using a low profile, non-slip material.12 month warranty
applies.
It has an ‘out-rigger’ press-stud pocket that will allow the insertion of a Smart-Caller
304Mhz or Cura1 433Mhz transmitter module.
Under this part number no transmitter is supplied,. Use this part number to purchase
replacement mats were existing transmitters may be redeployed.
Image
W/Sale $
RSP $
158
223
221
318
66
97
Transmitter
not included
See Sections 9 & 11 for suitable transmitting and receiving devices
See brochure at www.smartcaller.com.au
5.2
A-MAXI-MAT-433M
Pt No 2624-433M
(Cordless pressure
floor mat)
12 month pro-rata
warranty
5.3
A-CL433-TX-U5
Cordless Large Floor Pressure Mat with Cura1 433Mhz transmitter module
This cordless product is designed to immediately alert that a person had exited the
bed. It is a large (1200 x 600mm) pressure mat being warm underfoot. It is
waterproof and washable using a low profile, non-slip material. 12 month warranty
applies.
It has an ‘out-rigger’ press-stud pocket that includes a standard Cura TM-01 433Mhz
transmitter and therefore suits integration with other Cura 1 sub-systems described
within this catalogue.
The radio module includes a replaceable battery and has an anticipated battery life in
excess of 5 years having a wireless range of typically 15M.
See Sections 10 & 12 for suitable receiving devices
TRANSMITTER FOR ABOVE Sold seperatley
Page 14
5.4
A-CBP-01
Pt No 2629
(Cordless (wireless)
Bed Exit Pad, one
year version ; less
transmitter)
12 month pro-rata
warranty
CORDLESS BED EXIT PADS
Cura Cordless Bed exit Pad – Excluding transmitter module (1 year warranty)
By placing a Cura TM-01 transmitter module within the special neck envelope section
of the pad this pressure sensitive bed exit sensor uses wireless communication and
avoids cables across the floor.
Measuring 760mm x 510mm the CBP-01 pad is classified as a consumable item
having a 12 month life expectancy and warranty. 30 day and 3 month warranty
versions also exist for use in infectious and palliative applications. Contact SmartCaller for further information.
77.5
110.5
143.5
207.5
53
89.5
Transmitter
not
included
For complete operation it is necessary to select the receiver /controller unit model
CBM-01 listed below.
This Bed Pad part number does not include the transmitter module and is intended
as the part number applicable for purchasing replacement pads.
5.5
A-CBP-02-433M
Pt No 2629-433M
(Cordless (wireless)
Bed Exit Pad, with
transmitter)
Cordless Bed Exit Pad with Cura 433Mhz transmitter module
This represents the fully equipped Bed Exit pad with the TM-01 433MHz transmitter
supplied. It requires the CBM-01 receiver/controller for the pad to operate correctly.
See Sections 10 & 12 for suitable receiving devices
12 month pro-rata
warranty
5.6
A-SAFE-CHAIR-01
Pt No 2630
(Chair sensor pad
without transmitter
module)
12 month pro-rata
warranty
CORDLESS CHAIR EXIT PADS
Cordless Chair Pad – Excluding transmitter module(1 year warranty)
This one year warranty chair pad accommodates a Cura 433Mhz or Smart-Caller
304Mhz transmitter module within its out-rigger enclosure. Under this part number it
includes no transmitter and is the part number to ;use for supply of replacement pads.
3 month and 30 day versions are available for infectious and palliative applications.
Like the bed sensor it is an easy to clean non-allergenic soft PVC material printed
with detailed instructions. See Sections 10 & 12 for suitable receiving devices
Page 15
5.7
A-SAFE-CHAIR433M
Pt No 2630-433M
(Chair sensor pad
with transmitter
module)
12 month pro-rata
warranty
5.80
A-EZY-SEATBELT
Pt No 2636
(Easy release safety
restraint belt with
alarm)
Cordless Chair Pad – Including Cura 433Mhz transmitter module
This represents the fully equipped Chair Exit pad with the TM-01 433MHz transmitter
supplied.
It requires the CBM-01 receiver/controller for the pad to operate correctly (See
section 10).
You can also consider the SAFE-CHAIR 304M below as an alternative solution,
particularly if you are using an HP3 phone or HP4 Smart-Dialler as the control and
communication unit.
Also consider the EZY-SEATBELT described below if the Resident is inclined to fall
out of the chair or wheelchair. See Sections10 & 12 for suitable receiving devices
Restraint belt for people in chairs and wheelchairs with disconnect alarm
For use with chair and bed sensor (BME-03) this low cost safety belt is easy to
release and will generate an alarm if released by the resident.
It comprises a metal buckle with durable plastic casing and uses seat belt style
webbing.
Suits Smart-Caller bedside and communal area call-points.
Page 16
120
186.5
126
183
6. PORTABLE (CORDLESS) HIGH-CARE ROOM & WARD MONITORING SYSTEMS [GST Exempt & TGA Approved]
Item
6.1
6.2
Description
Wireless Bedside Pendant System -304Mhz
This unit allows a 304Mhz wireless pendant or any other wireless sensor or device to
trigger bedside (or other) call-points. It is particularly useful to allow residents who are
inclined to fall to carry or wear a personal emergency transmitter (PET).
Wireless trigger
device for hard-wired It can similarly be used with other wireless transmitter devices such as a PIR, Door
Reed, Bed-Wet (Enuresis) Sensor or other device where the portability of wireless is
call-point)
desired.
It includes a plug-pack jack incase power cannot be supplied from behind the callpoint. The standard version includes a fully enclosed 45mm deep box.
Suits wireless trigger connection to ‘Other Brand’ hard-wired call-points
Model
A-PENDANTALERT304M
A-BEDEXIT-PIR-01
(PIR BED EXIT
SENSOR)
6.3
A-MINI-CALL-01
433M
(A portable staff
duress or small
nurse-call system)
OUT OF BED CURTAIN PIR SENSOR WITH ON OFF SWITCH AND PLUG PACK
This small dimension Curtain PIR fits to the wall at the head of the bed in a purpose
built wall mount bracket. It is easy to install and can be moved from room to room
with ease. It projects an invisible beam to the end of the bed. When the residents
legs break this beam an alarm call is generated. Connects to all nurse call systems.
Wireless versions also available. Comes complete with wall mount bracket.
NOTE. THE STANDARD CONNECTION IS 6.3MM TIP AND SLEEVE STEREO
WIRED AS MONO. THIS SUITS MOST NURSE CALL SYSTEM. IF YOU HAVE
DOUBT THIS TYPE OF CONNECTION IS SUITABLE OR YOU WANT TO CHECK
CALL SMART CALLER FOR ADVICE
MINI CORDLESS NURSE-CALL SYSTEM CURA 433Mhz
As illustrated a typical system comprises up to 30 transmitting devices of various
types communicating with a central display unit which in turn is capable of
communicating with portable pagers.
The system illustrated includes six wall mount or lanyard pendant transmitters and a
single PIR movement sensor with the central equipment comprising a 30 channel
display unit (model QDP-02) and a single pager.
This illustrated set-up of equipment is a typical miniature wireless nurse-call system
with call-points and PIR movement sensor going to a 30 channel display receiver and
associated system pager. A wide variety of alternative configurations is possible by
selecting the requirement components and quantities from Sections 9, 10,14 & 19.
Also see next item for longer range mini nurse-call system that operates direct
to Carer’s normal (POCSAG) pager from the resident’s pendant or call-point.
Page 17
Image
160
230
159.5
213
Select prices
from
elsewhere
Select prices
from
elsewhere
6.4
A-POCSAG-CALL-01 LONG RANGE CORDLESS NURSE-CALL POCSAG 450Mhz
This call-point has the ability to communicate directly to a professional POCSAG
(A Call-point having
alphanumeric pager/s sending a preprogrammed text message. This model (As
direct communication configured with two button operation) would typically be programmed to give a text
of programmable text message with location and a call or cancel; event.
message to UHF
It typically provides up to 300M range direct to the pager, subject to building
POCSAG pagers)
constraints. It is ideal for connection to door wanderer systems, front door bell and
connection to essential equipment for reliable coverage of emergency events without
having dependence on other systems or facilities.
150
199
329
420
Note POCSAG Pagers not include in this price. Seek Pager prices from Section 18.
6.5`
N-DEMRAD-01
(Portable Dementia
room
communications
system)
(Remember to
select antenna)
CORDLESS DEMENTIA ROOM SYSTEM 304Mhz
Transportable (cordless) Dementia Room Controller
Deploying the 304Mhz frequency that automatically makes available a wide range of
wireless sensor devices the DEMRAD unit with its optional telephone wall-mounting
bracket can become the communications hub of a high care or dementia specific
care room.
It is capable of accommodating and controlling bed-exit, bed-wet, room exit, pacing,
overdue from Ensuite, Nurse-Call, Staff Assist and Cancel functions much the same
as the alternative fully cabled and permanently equipped rooms. It also allows the
facility to be a wireless ‘overlay’ to an existing nurse-call system.
Being a short-haul wireless device, the DEMRAD controller can simply be located on
the top shelf of the wardrobe or elsewhere. It is not affected by other DEMRAD
installations and it needs only a 12v dc power supply. If located near the bed it can be
powered from the existing battery backed nurse-call power source.
As a general guide it should be noted that almost all of the many sensors listed and
illustrated in Part B of this catalogue can be applied to the DEMRAD unit from time to
time and on a room to room basis as required.
Page 18
6.60
A-HOME-CARE KIT
Pt No 2580
HOME-CARE WIRELESS PAGER SYSTEM 433Mhz
Similar to the previous version this Cura system also offers direct communication
between resident and Carer’s pager, in this case using a Cura pager instead of a
(Home-Care/Granny standard POCSAG version.
Flat or similar special This Cura version is a totally portable mini system providing wireless button to belt
pager alerting application. It is packaged to include two wireless pendants each
application alerting
having mounting bracket plus lanyard for flexible use. The wireless buttons will
system)
typically have a range of 50-80M to the ton only alert belt pager this distance
depending on building construction constraints.
Other wireless transmitting devices such as the PIR, cordless bed and chair sensors,
smoke detectors etc can also be included as signal inputs to the pager/s. Also one or
more hallway monitoring units may be included within this localized stand-alone low
cost system.
You may need to include a Range Extender if you wish to monitor husband working
in the shed at the bottom of the garden.
The listed price includes one pager and two wireless button transmitters as
illustrated. Add other items as necessary. See Sections 9 & 10 for selection of
individual item descriptions.
Page 19
55
95
7. EPILEPTIC FIT - SEIZURE MONITORING & HOME-CARE ALERTING SYSTEMS [GST Exempt & TGA Approved]
Item
7.1
Description
Model
A-SEIZURE-ALERT- TYPICAL SEIZURE ALERT SYSTEM CONFIGURATION
01
Introducing the new Seizure Alert Monitor unit and exploiting various components
from the wide range of Cura aged care accessories listed in his catalogue, this
(A complete seizure comprehensive bed monitoring system will detect and trigger alarms should the
detection system for system detect periods of shaking or jerking movements such as those encountered
bed installation.)
by persons inclined to suffer fits such as tonic/clonic (grand mal) seizures.
It also detects & triggers an alert if it detects sounds that are analyzed as being
Selection of parts
sounds of distress.
Detects & Alerts
SEIZURE ALERT-01, as configured under this Part Number and illustrated will also
• Seizure,
raise an alarm should the patient exit the bed.
• Bed exit
With easy to use controls the Seizure Alert Monitor will send a wireless signal to the
chosen receiving device/s, in this case (as illustrated) to a centrally located 433Mhz
• Distress Noise
wireless receiver with alert tones, and/or will send the wireless signal to one or more
personal pagers in addition to closing a contact for triggering a nurse-call or
phone/dialer emergency-call system.
Seizure-alert-01 as illustrated includes
• Seizure Alert Monitor Unit Pt No 3000 [Essential part]
• Hallway Wireless Receiver Remote alarm [Optional] part] (can use pager or other
devices)
• Bed exit pad with BME or BMS control unit [Optional] or use portable (cordless
versions)
Page 20
Image
POA
1155
7.2
A-SEIZURE
MONITOR
Pt No 3010
(Epileptic fit and
distress sound
sensor unit)
Seizure and distress sensor for sleeping resident/patient
This control unit includes a low profile sensor that fits under the mattress
and detects shaking or jerking movement of the sleeping person and a
microphone and audio analytical circuit to detect noises that the detection
circuit deems to be the result of resident/patient distress.
Sensitivity controls exist for levels of mattress shaking and microphone
sensitivity control. It includes power on/off light and switch plus a detect
threshold level LED light to assist in set-up of sleeper’s movement during a
typical tonic/clonic (grand mal) seizure.
With closing contact alert and wireless transmitter trigger an extremely wide
range of alerting accessories is possible.
Accessories include most of those items shown within Sections 9, 10, 11 &
12 plus facilities included within the various Emergency-call and nurse-call
systems and sub systems described in alternative catalogues.
Unless connected to nurse-call power source this controller will require 12v
dc plug-pack (not included) and includes up to 24 hour battery back-up
Page 21
POA
943
PART ‘C’. – STAFF DURESS & OH&S PRODUCTS & SYSTEMS
8.
Item
8.1
Model
N-SAFE-T-NET
SYSTEM
‘Caring for Carers’
within building
STAFF DURESS OH&S SYSTEMS [GST Exempt & TGA Approved]
Description
‘SAFETY-T-NET’ STAFF DURESS SYSTEM 304Mhz
Integrated Nurse-Call System ‘SAFE-T-NET’ Umbrella
In addition to providing comprehensive monitoring for ‘Residents on the move’ or for
accommodating wireless accessories this low cost optional facility known as the
‘Safe-T-Net’ System comprises low cost 100-channel wireless receivers connected to
Nurse-call System Area Controllers.
It offers the benefit of personal wearer duress identification and (approximate)
location within a Smart-Caller SmartCare-1000 or Smart-Care-500 hard-wired nursecall system.
Smart-Caller Radiant-1000 & 500 systems already possess such capability by virtue
of their use of wireless devices including personal pendants and wrist worn
transmitters.
This technique also offers the benefit of ‘short haul’ wireless transmission whereby
the ‘long-haul’ aspects are carried by the cabled infrastructure and are subject to
constant polling thereby providing a ‘supervised’ facility.
Battery monitoring and reporting is applicable to all wireless transmitting devices.
The use of Extension Receivers, Range Extenders (Repeaters) and Transponder
devices provides extended coverage but dilutes the ability to identify the person’s
location. It is therefore important to consider various options prior to installing a
system.
The illustration also shows the nurse-call computer delivering SMS Duress calls to onsite and/or off-site mobile phone destination/s via a GSM/GPRS fixed Wireless
Transmitter (GSM USP Dongle).
Alternatively a Smart-Caller HD4 Dialler may be used to deliver a general
announcement voice to multiple destinations and/or data to central monitoring
service.
Page 22
Image
W/Sale $
RSP $
See Below
See Below
8.2
8.3
8.8
DURALINK SYSTEM SITE WIDE STAFF ALERT DURESS SYSTEM 304Mhz
DURALINK Supervised long range duress & general purpose communication system
‘Caring for Carers’
For sites that include many buildings and/or locations throughout a large site the
throughout site
Duralink Transponder System offers special benefits whereby it is capable of
delivering normal 304Mhz wireless traffic (which is normally limited to approximately
50-80M range) to be delivered up to 600M distant.
Up to 99 Transponders can be included in a single system each having its own
polling identification. Each Transponder within the system has its unique identification
and is being constantly polled by the base station and failure to respond to a polled
handshake will cause a trouble report. Calls delivered by a transponder automatically
receive a confirmation response from the base unit.
The Duralink has multiple applications whereby it can operate as a site-wide nursecall or Duress system or be applied to similar applications in building construction
sites or other industrial and commercial applications.
The system is also ideally suited to ‘stand-alone’ operation whereby it has no
dependency on existing communication infrastructures or central equipment.
www.smartcaller.com.au
SITE-WIDE STAFF ALERT DURESS SYSTEM 915Mhz
This system comprises a fully configurable wireless duress facility for health and
aged care sites, medical centers, building sites and factories where staff may be at
(Staff Duress system risk or production placed in jeopardy.
Alerting devices are waterproof and suitable for external locations and include
with wide ranging
portable wrist strap emergency transmitters, wall-mounting call and cancel points
functions)
including pull-cord activation etc. The caller ID and battery monitoring is carried when
using suitably equipped receiving devices a number of which are described below.
To satisfy OH&S requirements wireless indictor lights with sound alerting facilities
along with off-site dial-up capabilities are included in the overall range of equipment.
The system will satisfy the needs of a small medical centre where each Doctor’s
desk may have a hidden panic button or, using the CS-01 Desktop Care Station, the
system is capable of accommodating up to 1,000 portable and fixed call-points
covering up to eight separate locations.
Monitoring of staff, doors and machinery makes the Staff-Alert system ideal for
Health and aged care sites plus commercial and industrial applications.
See Below
See Below
POA
POA
112
163
N-STAFF-ALERT
915Mhz
A-TXP-02 PET 433M Wrist strap Duress Transmitter (including Strap 433Mhz
Like all wireless devices this small dimension personal transmitter has a unique
Pt No 2573
transmitting code which will facilitate identification Battery monitoring is also provided.
(Emergency Wrist
strap Tx button)
Page 23
8.9~
P-HD4 DOMESTIC
(Off site/On-site
Emergency-Call
device)
8.10
Emergency-Call telephone dialer
This Smart-Caller HD4 dialer (or the alternative HP4 phone) is able to direct a Duress
situation off-site up to 8 destinations delivering voice message and/or data
communication to any combination of mobile or fixed location phones and/or to one
or more on-site or central monitoring centers.
Visit www.smartcaller.com.au for data sheet
USB Version GSM Fixed Wireless Terminal From Nurse-Call computer
This unit with its SIM card (not supplied) will allow both-way GSM communication
(SMS deliveries to off- between the Host computer and various GSM mobile phones.
site mobile phones
It will for example deliver escalation or Staff Duress calls to off-site staff or
etc)
auto/manually compiled SMS messages to Maintenance, Security, Management,
Doctors or others as required.
This item is also ideal for allowing GPS tracker location traffic to be applied to a
Google map facility via a Winwatch Nurse-call software module.
Note. Make sure that your Winwatch software has the GSM SMS driver module for
this unit to communicate into the GSM network. (See WIN-GSM-01 in the Central
Equipment software section 28).
225
298
Approx 80
User to buy
direct
80
User to buy
direct
N-GSM FWT-USB
Page 24
PART ‘D’. – LIST OF WIRELESS TRANSMITTERS & RECEIVERS
This part lists all wireless transmitters & sensors plus Receivers for both 433Mhz (Cura) & 304Mhz (S/Caller)
9. 433Mhz (CURA) WIRELESS TRANSMSITTING DEVICES [GST Exempt & TGA Approved]
Item
9.1
Model
A-CL-433M-TX
Pt No 2719
(433Mhz Cura
Transmitter for floor,
bed and chair
sensors)
9.2
Description
433MHZ (CURA) WIRELESS TRANSMITTING DEVICES
Cura Cordless Mat/Pad Transmitter – 433Mhz
Fits within Floor, Bed and Chair sensor transmitter enclosure and triggers 433Mhz
alert signal. Communicates with CBM-01 (Pt No 2618) bedside controller (see
below).
It uses a Lith-ION long life battery with 12 month life expectancy covering
approximately 15M range.
Battery condition is monitored via the bedside control unit and batteries are
replaceable via service technician.
Note. Alternative Smart-Caller 304Mhz transmitter is model CPR304-UTIL-01 (See
item 3.14)
A-QTX-01 PET-433M Wireless Pendant/Call-Point 433Mhz
This push button wireless transmitter has universal application by being supplied with
Pt No 2584
both a lanyard for personal use and a smart wall-mount bracket.
Each transmitter has a unique code to allow identification where the parent receiving
(Wireless
device has that capability and it has a range of 80-100M in free space and 50 – 80M
Pendant/call-point
within buildings subject to building construction constraints.
transmitter)
Image
66
97
33
49.5
33
49.5
The pendant uses a replaceable A23S 12v Alkaline battery having a 5 to 10 year life
expectancy. Unlike other pendants in the overall range the low cost QTX series is not
waterproof.
9.3
A-RB-01-433M
Pt No 2585
(Common Cancel
wireless button)
Wireless Cancel/Reset transmitter -433Mhz
This push button wireless transmitter will reset active alarms that may be latched into
any receiver/display device. Like the call-point/pendant it is supplied with both lanyard
for carers to wear or may be wall-mounted with the wall mounting bracket supplied.
It has a range range of 80-100M in free space and 50 – 80M within buildings subject
to building construction constraints.
Page 25
9.4
A-PIRMS-01-PIIR433M
Pt No 2592
(Wireless Passive
Infrared Sensor)
9.5
A-WMAG-01 -433M
Pt No 2593
Miniature Wireless PIR Motion Sensor – 433Mhz
This miniature wireless PIR has many useful applications typically as a bed exit
sensor when set low to the floor to effectively scan the floor or as a sensor to identify
that the resident has entered the ensuite.
To assist in ease of operation it has an on-off switch and when switched on it has a
30 second delay to allow the care-giver to leave the room.
It has a range of 80-100M in free space and 50 – 80M within buildings subject to
building construction constraints.
It provides a wide angel view and will detect movement up; to 10M from the lens.
False calls can be triggered if pets are present.
Magnetic door reed alarm -433Mhz
With typically 50-80M direct range this unit is designed to monitor door opening
events.
(Door Reed contact
transmitter)
9.6`
A-UTIL-TX-01-433M
(Utility Transmitter)
9.7
9.8
A-BWP-01
A-CWP-01
Utility Transmitter for general purpose applications – 433Mhz
This unit is designed to allow any third party device to be able to communicate into a
Cura receiver or network.
A connection that represents a closing contact will trigger the transmitter complete
with its unique code and battery monitoring capability.
48
68
35
52
30
42
38
54
TBA
TBA
Bed wet pad detects when a petient of resident is incontinent in the bed. Connects
to nursecall system (GCORD and Monitor requied)
CHAIR WET PAD detects when a petient of resident is incontinent in the chair
Connects to nursecall system (GCORD and Monitor requied)
Page 26
10. 433Mhz (CURA) WIRELESS RECEIVING & PROCESSING DEVICES [GST Exempt & TGA Approved]
Item
10.1
10.2
Description
Model
A-CBM-02-RX -433M 433Mhz (CURA) RECEIVING/PROCESSING DEVICES
Pt No 2718
Universal Receiver/Controller for Cordless (wireless) Bed, Floor or chair
sensor Pad, dual capability.
(Cordless
Powered via a 9v snap-on battery or plug-pack or wired into the back of the adjacent
Receiver/Controller
call-point it monitors both its own battery condition and that of the long-life battery
with dual reception
contained within the 433Mhz sensor’s battery.
capability for Bed
It is a universal dual controller whereby it suits cordless bed, floor and chair sensors,
Exit, Floor, and Chair) has an adjustable audible alert, includes an adjustable alarm delay control and
provides a 6.3mm socket to allow the alarm condition to be delivered to the bedside
Don’t forget
call-point. It provides the capacity not only to operate as a Single monitor, but also
can operate with 2 cordless products and can work with a pager.
mounting bracket
and cord to bedside Various mounting brackets are available including a 6.3mm socket to allow for an
interconnecting lead to connect to the 6.3mm socket on the call-point. (Other callcall-point and
point connectors can also be accommodated by prior arrangement). See Sections 37
perhaps a plugpack See Section 37 & 16 for details and prices for the interconnecting lead to the call-point and various
mounting brackets.
This universal sensor receiver/controller also provides a ‘supervised’ monitoring of its
programmed sensor by raising an alarm should the sensor be out of range of the
controller or should an incorrect sensor have been placed on the bed, chair or floor.
A-HRA-01 -TX-433M Hallway Alarm Unit – 433Mhz
This unit is intended for fixed location placement and it provides an adjustable
Pt No 2586
audible plus a visual alarm for up to 30 transmitter devices located from distances of
(Hallway Alarm unit) up to 50-80M.
Image
W/Sale $
RSP $
110
163
70
105
47
68
It can be powered by either plug-pack or battery
10.3
A-PAC-02 PAGER433M
Pt No 2582
Voice and tone Pager- 433Mhz
This is a low cost system dependent pager (not using POCSAG protocol) with
typically 80M range from the transmitter/s.
(Wireless belt pager Supplied with two AA batteries.
with multilingual
voice and tone alerts)
Page 27
10.4
10.6
A-PAG-03DV – 433M Pager with LCD display, multilingual voice messaging and tones plus vibration.
With a belt clip and on/off switch this pager operates from two AA batteries
Pt No 2581
(supplied). It has approximately an 80M range from most transmitters and this range
can be extended by use of pager range extenders model WBUMQ described below.
(Pager with voice,
tone numeric display
& vib)
A-QDP-02 -433M
Pt No 2600
(30 Channel Display
unit)
58
87
150
230
30 Channel Display Unit 433M
This wall mounting display unit is capable of monitoring up to 30 transmitting devices
whilst identifying the ID number of the alarmed device/s. It also has the capability of
onward paging to a variety of Cura pagers.
Having 50-80M reception range from its family of transmitting devices and in addition
to providing a visual display it is capable of voice annunciation of the alarmed
device/s identification number and will on forward the digital or voice paging
messages to the variety of Cura system pagers.
It can be battery or plug-pack powered and has selectable voice, tones and alarm
being adjustable in volume.
Page 28
11. 304Mhz (SMART-CALLER) WIRELESS TRANSMITTING DEVICES (Suits Phones, Diallers & Systems)[GST Exempt]
Item
11.1
Description
Model
A-BP-PET-304-GRA Professional Version Blue-Phone/HP3 Pendant (Grey)
This is the standard issue waterproof pendant (as supplied with the HD4 Dialler). It
also suits HP2 (yellow dot) phones. Being a Grey colored Pendant with iridescent
(Professional version (glow in the dark) button for Medical applications. Use this version for all HP2, HP3,
Blue or Grey
HD4 and other 304Mhz 24-bit wireless applications.
Pendant)
All versions include user replaceable 3.3v Lithium batteries and no special tools are
required. It includes low battery reporting which occurs as 2.63v.
Image
1-9=44
10+=40
69
68
1-9=44
10+=40
69
68
58
79
13
22
13
22
This is the standard issue product supplied with all Emergency-call phones and
dialers.
11.2
A-BP-PET-304-MAR Professional Version – Arm /Disarm Pendant
Same as the blue and grey medical pendant but without the iridescent treated button.
Intended as a security arm/disarm or other special (non medical) applications. The
(Professional version main difference between the two versions is the color of the plastic housing. Also
suits HP2 (Yellow dot) phones.
Maroon Pendant)
This colour pendant is primarily used for special applications such as HP3 wireless
activated security Arm/Disarm and as Carer’s global Cancel pendant for wireless
activated alarm calls from devices that do not have a cancel button (such as
resident’s pendant’). LIMITED STOCK / SOME BLUE ALSO AVAILABLE 11.3
A-PET 100-683
Multipurpose Personal Emergency Transmitter (PET)
Splash proof 304Mhz wrist strap transmitter (which includes a neck chain).
(Multipurpose Wrist
strap, necklace PET) This model offers the benefit of both wrist strap and necklace solution for both
Independent Living and low-care/ High Care applications.
11.4
A-BP-PET-S/CODE Service cost to provide specific transmitter code
(Supply special code) To provide special Pendant TX address code for any new supply BP-PET transmitter
- Service charge
11.4A A-CODE CHANGE
(To change code for
call-points)
Service cost to provide specific transmitter code
To provide special Pendant TX address code for any new supply BP-PET transmitter
- Service charge
Page 29
UPGRADE
11.5
A-CPR304-GPWP-02 GP Waterproof Single button wireless Call-Point
Wall mounting waterproof 304Mhz call-point. Call only (no cancel or assist). Includes
(Single button
user replaceable Lithium Battery.
waterproof alarm
Note. For extreme water jet conditions it is recommended to run a silicon seal around
only call-point)
the top and side edges of the call-point to ensure waterproofing. Product guarantee is
void if water damage is incurred without evidence of natural cure silicon seal.
11.6
A-CPR304-GPWP-03 GP Waterproof Single button wireless Call-Point with Slave Connection
As above but with plug-in connection to allow connection of a basic parallel call-point,
(As above but with
i.e. one having no LED display such as a ceiling mount slave call-point model SCPslave connection)
H1G-CM-03 or similar appearance wall-mounting model SCPGPWP-02.
11.7
N-CPR304-APWP-01 Waterproof Master 2-button wireless call-point
As above but master call-point including call, cancel and assist. - 01 for battery - 03
(Two button wet area for 12v supply
Wireless call-point
Unlike the above model this unit includes the call plus a feint colored cancel button
with call, cancel and above the call button.
assist)
Note. It is necessary to run a silicon seal around the edge of the call-point to ensure
waterproofing. Product guarantee is void if water damage incurred without evidence
of natural cure silicon seal.
11.8
11.9
11.10
N-CPR304-H-PC-01
(Wireless bedside
Call-point)
Bedside wireless master 2 button wireless call-point
"H" series call-point with call, cancel, assist and cord pendant socket including lithium
battery. Based on standard Clipsal 2000 series faceplate.
N-CPR304-H-PC-02
(As above)
Bedside wireless master call-point
As above but to operate from external 12v or 24v dc supply.
Communal Area wireless call-point
As above but to operate from external 12v or 24v dc supply
Page 30
76
73
1-9=75
10-49=67
50+=60
102
91
85
1-9=87
10-49=79
50+=74
122
112
101
As above
As above
1-9=85
10-49=77
50+=72
116
106
102
As above
As above
As above
As above
N-CPR304-H-XX-01 Communal Area wireless call-point
(Wireless Communal As model CPR304-H-PC-01 above but without 6.3mm cord pendant socket – Inc
C/Point)
battery
11.11 N-CPR304-H-XX-02
(As above)
1-9=58
10+=54
As Above
11.12 P-CPR304-H-GP-01
(As above but callonly)
Communal Area Wireless Call-Point
As above but without a cancel button. Recommended for use with Blue-Phones and
Smart Diallers where cancel should be via the phone/dialer cancel button.
11.13
Emergency wireless Call-point with Call and Cancel
Forming part of the standard nurse-call ‘H’ (Hospital) Series call-point faceplates this
model will blend in with either a hard-wired and/or wireless nurse-call system using
identical appearance (other than the Emergency button) to the other call-points
throughout the site.
11.14
11.15
N-CPR304-H-EMG01
(Wireless emergency
Call/Cancel)
Emergency wireless call-point – Flush mounting
This momentary contact 40mm button assembly includes a momentary LED
(Wireless Emergency indication and includes a 304Mhz standard wireless module. Being battery operated
C/Point, call only
it is an alarm call only device
version)
Note, the switch assembly protrudes to a depth of 40mm from behind the faceplate
therefore (unless you are penetrating plaster, you should consider the surface mount
(boxed or mounting block) versions.
As above
As above
1-9=85
10-49=77
50+=72
116
106
102
66
91
82
115
66
91
N-CPR304-EMG-01
N-CPR304-EMG-02
(As above, surface
mount)
11.16
As Above
The ‘Emergency’ label can be changed to suit other applications as required. Emergency wireless call-point – Surface Mounting in enclosed box
As above but mounted within a 45mm mounting Box.
Overall dimensions are 115L x 70W x 52Hmm plus 25mm button height
N-CPR304-EMG-03
A flush mounting button with button protection surround
This model uses the same switch mechanism as the CPR304-EMG-01 and 02 but
(Wireless Emergency the button assembly is set into the button surround so that the button cannot be
C/Point)
pressed accidentally.
The button diameter is 20mm and the total button assembly (fixed surround with
flush button) extends 20mm from the faceplate surface.
The ‘Emergency’ label and button color can be changed to suit other applications as
required.
Page 31
11.17
N-CPR304-EMG-04
(As above, surface
mount)
11.18
11.19
Wireless Door Bell (or utility) push-button
Ideal for doorbell or emergency call purposes from the shed or Granny flat. Can be
(Local alert/Door Bell) taught into phone or dialler, as a local alert not intended for outward dialling. (Also
suits outward dialling if so programmed.
N-CPR304-CM-01
N-CPR304-CM-02
(Ceiling pull Cord
Wireless Tx)
11.21
11.22
11.23
Ceiling pull-cord wireless transmitter (battery powered)
Standard ceiling pull-cord call-point with fitted utility alarm only 304Mhz transmitter
with lithium battery.
Also suits HP2 (Yellow dot) phones.
Ceiling pull-cord wireless transmitter (system powered)
Standard ceiling pull-cord call-point with fitted utility alarm only 304Mhz transmitter
drawing power from 12v system supply.
Also suits HP2 (Yellow dot) phones.
113.5
53
71.5
75
103
77
106
1-49=44
50+=39
65
59
1-49=42
50+=38
63
56
47
68.5
47
68.5
As Above
A-PET-PCB-01
General-purpose miniature wireless transmitter pcb; with battery
(Pcb only with battery) With a 30mm diameter this is a complete transmitter with integral antenna and fitted
lithium battery. This stand-alone 304Mhz transmitter is ideal for use within smoke
detectors or other devices where a closing contact is able to trigger a 2sec
transmission burst using standard Smart-Caller/NESS 24-bit protocol. Illustration
shows reverse side with fitted and removable lithium battery
A-PET-PCB-02
(Less Battery)
General-purpose miniature wireless transmitter PCB; without battery
As above but without Lithium battery.
CPR304-UTIL-01
Utility Wireless transmitter (packaged with battery)
Using the PET-PCB. As above but contained in a 5cm x 4cm x 12cm water resistant
plastic box including 3v lithium non-rechargeable battery.
(Utility 304Mhz
transmitter)
11.24
81
A-100-283
(Ceiling pull Cord
Wireless Tx)
11.20
As above but mounted within a 50mm mounting Box
Emergency wireless call-point – Surface Mounting
Overall dimensions are 115L x 70W x 52Hmm plus 25mm button height
A-CPR304-UTIL-02
(Utility 304Mhz
transmitter)
Utility Single channel Wireless transmitter (packaged without battery)
As above but without internal battery but capable of external 12v dc supply & external
LED drive.
Page 32
As Above
As Above
11.25
A-PTX304-GP-01
(Portable UHF
wireless GP
Transmitter)
Portable General Purpose Wireless Transmitter with 6.3mm socket
This model is intended to be used with floor mats, and other sensor and/or trigger
devices that are fitted with a 6.3mm stereo plug (as used for over-bed cord
pendants).
51
68
55
75
126
180
150
214
108
154
128
184
It includes an integral and replaceable lithium battery and is contained in a cabinet 90
x 45 x 35mm.
11.26
11.27
A-PTX304-GP-02
This model has 3M dual lock fixing pads (like Velcro but industrial grade)
P-MULTICODE-09NB
(No battery B-Up)
Multicode Hard-wired Input controller 9 Channel
Where some cabling may be preferred (instead of using battery operation) for call
points and room sensors, the Multicode allows from one (1) to nine (9) two-wire
connections to various N/O contact input trigger devices.
(Multiple code
transmitter located
on line cord)
11.28
11.29
11.31
P-MULTICODE-09BR
(With Battery backup and RJ
Connector)
Deleted
A-FIDSC-9VDC-01
(Wireless Smoke
Detector Battery
version)
11.32
Simply connect 12v power and slave input connections via the RJ sockets. The units
may be fully configured to provide up to 9 alarm only circuits or may include any
combination of alarm or cancel circuits to the number of 9 circuits in total. When
used with Phones and Diallers it is usual to provide alarm only circuits and to use the
dialler/phone’s cancel button, or, where the phone/dialler may be out of reach (such
as used in a community centre) it is possible to provide one cancel button to reset all
or any alarmed circuits. Multicode will support a momentary LED indication on each
momentary call-point if so required.
Use the SCP-GPWP-01 and SCP-H2-XX-01 call points with Multicode.
IN-LINE MULTICODE - Plug and Play
This Multicode is best described as an in-line units where as connection at one end is
directly to the HD4 Dialler or Blue phone and the the line and hardwired inputs
connect at the other end. This unit comes complete with battery back up and is
powered via the HD4 Dialler or Blue Phone.
Battery operated Smoke Detector including PET-PCB Wireless TX
Firetronics Ionization type battery operationg smoke detector including fitted 304 Mhz
transmitter module using smoke detector's battery supply
As Above
Note GST is applicable to smoke detectors.
A-FIDSC-240VAC-01 240v Operated smoke detector modified to take PET-PCB Wireless Tx
Firetronics ionization type 240v AC operating smoke detector with NiMH battery
(Smoke Detector
backup and including a fitted 304Mhz transmitter using the smoke detector’s battery
240v version)
supply.
Page 33
11.33
A-VSMOKE-DET-01
Vocal Smoke Detector: Stand Alone
11.33A A-VSMOKE-DET-TX Vocal Smoke Detector with transmitter- to work with Smart Caller phones and
systems
9V Smoke Detector with additional feature of recording a 14 second message.
Allows people with lower cognitive function to be informed what the alarm is and be
reminded of their fire plan. Can be a 'stand alone' item (V-SMOKE-DET-01) or with a
fitted transmitter (V-SMOKE-DET-TX) can send an emergency call through any
Smart-Caller systems such as the HP4 BluePhone or Smart-Dialler.
11.34
A-PIR-SC-02-304M
(Universal SmartCaller wireless PIR)
A-BEDEXIT-PIR-01
(PIR BED EXIT
SENSOR)
OUT OF BED CURTAIN PIR SENSOR WITH ON OFF SWITCH AND PLUG PACK
This small dimension Curtain PIR fits to the wall at the head of the bed in a purpose
built wall mount bracket. It is easy to install and can be moved from room to room
with ease. It projects an invisible beam to the end of the bed. When the residents
legs break this beam an alarm call is generated. Connects to all nurse call systems.
Wireless versions also available. Comes complete with wall mount bracket.
NOTE. THE STANDARD CONNECTION IS 6.3MM TIP AND SLEEVE STEREO
WIRED AS MONO. THIS SUITS MOST NURSE CALL SYSTEM. IF YOU HAVE
DOUBT THIS TYPE OF CONNECTION IS SUITABLE OR YOU WANT TO CHECK
CALL SMART CALLER FOR ADVICE
11.37
A-BEDEXIT-PIR-05
DUAL PIR - OUT OF BED CURTAIN PIR - Same as BEDEXIT-PIR-01 but has dual
PIRS interconnected. One each side of the bed
Suitable for beds that can be accessed from either side, (not against a wall)
Comes with a power pack wall mounting brackets and a in Line ON/OFF switch
located where it connected to the call point. Comes complete with 2 wall mount
brackets.
11.38
A-DOOREXIT-PIR304M
WIRELESS OUT OF DOOR/BED CURTAIN PIR - 304 MHZ
Works with all Smart Caller receivers. Ideal for use with RDU-05 and HP4.
Complete standalone unit which is equally as effective to detect someone passing
though a doorway as it is to detect out of bed. Uses 9 volt battery power supply.
Comes complete with wall mount bracket.
IDEAL FOR
DOORWAYS ALSO
90
98
140
90
140
159.5
213
192.5
280.5
165
236.5
Battery operated Wireless PIR (Complete with-off switch)
This model is compatible with all Smart-Caller wireless products. This unit provides
an approximate 8M radius over a 120-degree field of view.
Like most wireless PIRs the unit will go into sleep mode. The sleep mode is
approximately 30 seconds therefore you should ensure the receiving device has the
ability to ‘reject same calls’ for the required period (typically 3 to 5 minutes).
11.36
63
Page 34
11.39
11.40
BRACKET FOR BED-EXIT PIR
A-DOOR-REED304M
Due to the normal requirement for the sensor to be mounted above the door it is
supplied with a plug-pack and an ‘in-line’ on-off switch with LED indicator which will
apply power to activate the device.
(Wireless Door Reed)
11.40
N-DOOR-REED-HW
8
15
45
61
13
17
STANDARD HARDWIRED DOOR REED SWITCH
Page 35
12. 304Mhz (SMART-CALLER) DECENTRALIZED WIRELESS RECEIVING DEVICES [GST Exempt]
Item
12.1
Model
A-RDU-01
Description
Image
W/Sale $
RSP $
65
90
112
160
121
173
Fixed location wireless receiver 304Mhz (or 433Mhz) for Strobe/Siren or similar
(Wall mount 304Mhz kit.
Receiver with relay
This model uses an “H” series call-point faceplate with integral 304Mhz receiver and
latching facilities)
decoder plus N/O-N/C latching relay with reset timer options and reset button.
Irrespective of it being used to control a strobe light from an HP3 Phone or HD4
Dialler this product is suitable for any application where it is required to activate a
closing or opening contact via a wireless pendant or other form of compatible
transmitter or sensor and to have either manual or timed unlatching of that relay.
Being a receiving device it requires a constant 12v dc supply. It may be surface
mounted using a standard 35mm mounting block or recessed within the plaster wall.
(See below)
12.2
A-RDU-03
(Wireless trigger
device for hard-wired
call-point)
(Select Pendant or
other 304Mhz
transmitter device
from within previous
section)
12.3
A-ROOM-CONTRL01
Wireless Receiver with programmable relay including cord with 6.3mm Plug &
Plug Pack
This unit allows a 304Mhz wireless pendant or any other wireless sensor or device to
trigger bedside (or other) call-point. It is particularly useful to allow residents who are
inclined to fall to carry or wear a personal emergency transmitter (PET).
It can similarly be used with other wireless transmitter devices such as a PIR, Door
Reed, Bed-Wet (Enuresis) Sensor or other device where the portability of wireless is
desired.
It includes a plug-pack jack(and plug-pack) incase power cannot be supplied from
behind the call-point. The standard version includes a fully enclosed 45mm deep box.
CHANGE ANY OLD CALL POINT TO NEW - INCLUDES WIRELESS RECEIVER
Simply plug into your existing call point via the 6.3mm connection and take
advantage of all the benifits a modern call point has to offer.
Benifits like low cost modern pendant cords (bell Presses) having an on-board
wirelss receiver means you can now provide the resident remote pentants, fixed
wirelss call points, unobtrusive PIR out of bed sensors and floor mats. Easily
installed by a maintence type person or have proffessionally installed see the 02
model.
9 volt plug pack included.
Page 36
12.4
12.5
A-ROOM-CONTRL02
N-WPM-02
(Safe-T-Net 100channel Wireless
Receiver option)
(Remember to
select antenna)
HAVE THE ROOM CONTROLLER FITTED OF BY AN INSTALLER FOR A TRULY
PROFFESSIONAL LOOK
Provides all the features above. Simply wire the room controller into the existing call
point mechanism and utuise the existing call points power source if present. Can
usually be fitted off over the old existing call point for a truley proffessional looking
upgrade. The 02 model does not come with plug pack or mounting box as these are
not normally required when fitted off proffessionally.
105
155
150
215
Safe-T-Net Wireless Receiver with extension receiver Connector
This 304Mhz receiver will allow any 16 or 32 way hard-wired slave area controller to
receive and process up to 100 channels of wireless devices. These may include
pendants, utility transmitters, wireless call-points, bed exit and bed wet sensors,
wander alert and doorbell alerts and similar compatible wireless devices. It will also
accommodate the RX304-BUS-01 extension Receivers.
It also acts as a solution for staff duress and will also accommodate most of the
NESS manufactured standard 24-bit protocol wireless devices. Check compatibility if
using new NESS devices.
This unit draws its power from, and connects to the nearest –02 series Slave
controller using RJ12 to RJ12 cable connection which should not exceed 30M and
should be protected from areas of electrical interference.
It will also accommodate the RX-EXT-01 Extension receiver which significantly
increases the input wireless range, however in doing this remember that you will
accordingly reduce the ‘pin-point’ location capabilities due to the original WPM-02 call
input coverage range being duplicated for each extension receiver fitted.
Page 37
12.6
N-WIC-1000S
(UHF Wireless area
controller)
Wireless Area Controller (100 Channel) (Forms part of SmartCare-1000 polled
system)
Operating as a slave controller being polled by a central equipment ASM-0x or WIC1000M master controller the WIC-1000S will monitor, accept and process up to 100
individual wireless codes with call, cancel, assist and low battery traffic.
(Remember to
select antenna)
It may be included within a hard-wired system and visa versa. Up to 99 controllers of
either hard-wired and/or wireless may be included within a system of up to 1.4kM
cable length.
561
As a typical alternative the safe-T-Net receiver may be used in conjunction with a
hard-wired AS16S or AE32S hard-wired controller.
Page 38
747
12.7
N-DEMRAD-01
(Portable Dementia
room
communications
system)
(Remember to
select antenna)
care room.
illustrated in Part B of this catalogue can be appliedAs a general guide it should be
noted that almost all of the many sensors listed and illustrated in Part B of this
catalogue can be applied to the DEMRAD unit from time to time and on a room to
room basis as required.
Apart from perimeter safe containment covered elsewhere in the catalogue, there is
now no need to relocate a resident due to the threshold effects of Alzheimer’s and
dementia, instead it is better for the resident and the budget to bring the monitoring
facilities into the room on a need be basis.
SUITS ALL EXISTING SMART-CALLER HARD-WIRED AND WIRELESS NURSECALL SYSTEMS & CAN BE APPLIED TO OTHER BRAND SYSTEMS to the
DEMRAD unit from time to time and on a room to room basis as required.
Page 39
1-9=329
10+=POA
420
PART ‘E’. – WIRELESS (& PAGING) EXTENDERS, REPEATERS & TRANSPONDERS
This part describes all devices designed to extend the range (coverage) of 304Mhz and 433Mhz systems
13. SMART-CALLER EXTENSION RECEIVERS, REPEATERS & TRANSPONDERS (UHF) 304Mhz [GST Exempt]
Item
13.1
Model
EXPLANATION
(Ensuring that you
select the most
appropriate
accessory)
Description
EXTENSION RECEIVERS, DIVERSITY Receivers, REPEATERS & Transponders
Explanation.
• Extension Receivers can be additional receivers connected to a prime receiver or
receiver bus
• Repeater is a device that receives a signal then retransmits it as an identical
transmission
• Transponder changes the incoming signal to a different outgoing protocol,
frequency and power
Extension Receivers. If it is possible to extend a cable from a prime receiver (as
listed in section 13) to difficult reception areas, the least cost solution is to connect
one or more Extension Receivers. If using multiple extension receivers then an RJ
‘switch box’ should be used to provide independent connections into different
locations.
Diversity Receivers allow multiple receivers to be located on a communication bus
for delivery to a prime or head-end receiver.
Repeaters. These are ideal for capturing call traffic from one difficult location (such
as a separate building) and, after a short and programmable delay, repeating that call
using the same protocol and frequency but at a more efficient radiating power to
provide better range.
Transponders. These are similar to Repeaters but change the protocol, frequency
and/or power in order to change protocol, frequency or to exploit higher power
allowable on some frequencies but not on others.
Note: It is necessary to provide mains power to a Repeater or Transponder in order
to maintain battery back-up facilities, whereas an extension or diversity receiver is
powered from its parent receiver.
Page 40
Image
W/Sale $
RSP $
See below
See below
13.2
N-RX-EXT-01
(Extending the range
of wireless
processing
equipment)
Plug-in extension wireless Receiver
Although not exactly a stand-alone device, this item can significantly enhance the
performance of stand-alone receivers.
1-5=150
6+=POA
199.5
POA
150
POA
215
POA
150
215
Due to achievable range of 304Mhz transmissions being fraught with difficulties
within building layouts plus the problem of using multiple range extenders, the use of
Multi-receiver ‘splitter a small network of multiple receiver units associated with the call processing
equipment in a particular area can be a low cost and effective solution in such
box’. Not included
environments.
See below.
The use of one or more of these receiver units can significantly expand the reception
range of products such as the WIC100, WIC-1000M, WIC1000S, WPM-01 SafetyNet Receiver, range extenders and Diallers to name a few. The Receiver is fitted
with an RJ connector. Make sure that the correct parent item (with corresponding
remote Receiver RJ socket) is selected. Use an RJ splitter unit (as illustrated) if
additional Receivers are required.
Note. See splitter boxes below should you need to connect multiple Extension
Receivers.
13.3
N-RX-DIVERSITY-01 Diversity receiver/decoder
This unit when fitted with its optional decoder chip will receive , decode and amplify
(UHF Bus network
all 304Mhz wireless traffic allowing the decoded and amplified data to be delivered to
prime receiver)
parent equipment that will process that traffic to the head-end system.
(Remember to select Using the RJ Splitter Box (see below) or similar RJ adaptor, it is possible to create a
Network bus using the 02 model (without decoder chip) as ancillary receivers thereby
antenna)
extending the overall reception coverage whilst amplifying the overall data processing.
13.4
N-RX-DIVERSITY-02 Space Diversity Network/Bus Receiver module
(Multiple receiver
This device is identical the Diversity receiver -01 but excludes the Decoder
network device)
chip. In this case the receivers RJ pins connect to the LAN and the network
(Remember to
select antenna)
relies on the parent Diversity Receiver’s decoding and amplification facilities.
Page 41
13.5
13.6
N-RJ-SPLITER BOX RJ connection Box for RX-EXT-01 multiple receivers
This box allows the connection of up to 5 RX-EXT-01 receivers or RX-Diverxity-01
(A six socket
Receivers to any equipment that is suited for extension receiver connection. If using
‘connection bus’ for
a single Extension/Diversity receiver no such interconnection box is necessary. If
multiple use of RXusing more than a single Extension/Diversity Receiver it is necessary to use this
EXT-01 units)
Splitter box that parallel interconnects up to 5 external receiver devices plus one
connection to the parent equipment item.
N-WRX-304-01
(UHF Range
Extender- Repeater)
(Remember to
select antenna)
New Item
47
67
273
375
UHF Range Extender (Repeater)
Designed to allow the range of 304Mhz call-points, pendants and other transmitting
devices to be significantly extended to a further 150 -300M depending on building
construction constraints.
The design is such as to allow multiple WRX units to operate in the same location
due to the ability to independently set the repeat transmission and ignore same call
intervals. This allows considerable flexibility in designing wireless systems whereby
calls will be carried from repeater to repeater without the usual ‘Ping-Pong’ effects or
carrier frequency signal overlap causing corrupt signaling.
The WRX-304-01 includes a plug-pack and integral battery back-up and via its BNC
connector will allow either low efficiency ‘Rubber Ducky’ (flexi) antenna connection or
connection of efficient external or roof cavity mounted antenna via coaxial cable
connection (See antennas in section 34).
Page 42
13.7
N-DURALINK-TP-01 WIRELESS TRANSPONDERS – DURALINK SYSTEM
Duralink 304Mhz to 433Mhz UHF Transponder
(Duralink sending
Acting like an extended range WIFI system, this Transponder unit accepts normal
end Transponder)
Smart-Caller, Ness and Smartlink 24-bit 304Mhz wireless traffic and retransmits it at
the higher allowable transmitting power of 25mW using digital transmission on
(Long Range WIFI)
433Mhz. This can extend the range of the original transmission typically up to 600M
in free space and typically 150M in a building environment.
(Remember to
select both 433Mhz For maximum reliability each Duralink Transponder is constantly polled by its head
end polling controller (Model Duralink-BS- XX) and all received call traffic is
and 304Mhz
confirmed back to the sending end Transponder before onward processing.
antennas)
Each Transponder is capable of sending regular test calls and will report a low
battery or power fail condition to its master controller head-end. Up to 99
transponders may be used within a single system.
541
720
341
453
451
599
These transponders can only communicate with their respective head-end master
controller DURALINK-BS-01 (next item) and therefore provides a totally independent
communications system, which also makes it ideal for Staff Duress applications.
All range extenders and Transponders are supplied with NiMH battery back-up and a
plug-pack. It will be necessary to select your preferred 304Mhz antenna. See Section
34 for antenna selection.
13.8
13.9
N-DURALINK-BS-01 Duralink Base Unit for connection to host computer
(Base unit )
This version of Base Unit simply offers a serial port connected ADEMCO protocol for
connection to the host computer. It is capable of controlling up to 99 Duraliink
transponders.
(Remember to
select 433Mhz
Refer to ‘Duralink’ data sheet for system configuration details.
antenna)
N-DURALINK-BS-02
(As above but
including the
reconstitution of
original 304Mhz
transmission)
Duralink Base Unit for connection to host computer or wireless retransmission
As an alternative to the above facility this model also delivers a reconstructed original
wireless transmission on the original 304Mhz frequency. The latter allows the signal
to be connected into the WIC-100/200 wireless controller for canned message
dispatch and/or be delivered into a nearby HP3 phone, HD4 Smart-Dialler or perhaps
to a Site-Wide Dialler, the latter being capable of processing up to 256 incoming
wireless and subsequent monitoring centre client codes.
(Remember to
select 433Mhz
antenna)
Page 43
As Above
13.10
A-PAGE-REPEATALPHANUMERIC POCSAG PAGING REPEATER
VHF
Alphanumeric paging repeater Vhf/Uhf
PAGE-REPEAT-UHF When having problems trying to page staff within the underground car park or in
similar locations that are out of range of the original paging transmitter or otherwise in
areas being obstructed such as XRay department screen rooms, this Paging
(Extending Pager
Repeater offers an ideal solution.
traffic into difficult
locations)
The Repeater if placed in a location of reasonable quality reception will accept and
buffer the call and after a 4 to 5 second delay will retransmit that call on the same or
(Remember to
(if preferred) alternative paging frequency..
select antennas)
It is necessary to advise the receiving and required retransmission frequencies when
seeking price and delivery information.
Page 44
POA
POA
14. CURA EXTENSION RECEIVERS, REPEATERS & TRANSPONDERS (UHF) 433Mhz [GST Exempt]
Item
14.1
Model
A-QDP-02 -433M
Pt No 2600
Description
30 Channel Display Unit 433M with Pager range extender facility
This wall mounting display unit is capable of monitoring up to 30 transmitting devices
whilst identifying the ID number of the alarmed device/s. It also has the capability of
onward paging to a variety of Cura pagers.
(30 Channel Display
unit with Pager range
Having 50-80M reception range from its family of transmitting devices and in addition
extender capability)
to providing a visual display it is capable of voice annunciation of the alarmed
device/s identification number and will on forward the digital or voice paging
messages to the variety of Cura system pagers.
It can be battery or plug-pack powered and has selectable voice, tones and alarm
being adjustable in volume.
Page 45
Image
W/Sale $
RSP $
150
230
PART ‘F’. – BEDSIDE CORD & WIRELESS PENDANTS & ADAPTORS
15. BEDSIDE CORD PENDANTS [GST Exempt & TGA Approved]
Item
15.1
Model
A-PC731-3M
Description
Image
15.2
A-PC731-5M
15.3
A-BARREL-GRIP-3M Barrel Grip Cord Pendant, - 3M
This model has an ergonomic design handle to allow better finger press for those
(Optimum grip Cord with hand dexterity problems.
Pendant for Easy
handling)
Like all other models in the Smart-Caller pendant range it includes a right angled
6.3mm jack and alligator clip to ensure secure fixing to the call-point and bedclothes
respectively.
15.4
A-951027-2A-3M
(Standard Cord
Pendant)
15.5
A-951027-2-3M
(Enhanced cord
pendant with
momentary contact
light switch)
See Section 23 for
cord pendant light
switching
Accessories
W/Sale $
RSP $
27
39
39
57
27
39
40
47
47
62
Pendant cord with 6.3mm jack, 3M
Pendant cord with 6.3mm jack, 5M
Pendant Cord with 6.3mm jack 3M
Although slightly more expensive than the PC731 version this model is better suited
to arthritic hands and is a more robust device with 1 M more length.
Like all of our quality cord pendants it has a robust cable and sealed cord-grip
section along with a right-angled 6.3mm jack, however, this version has a distinct
button press (tactile) feel and sound response as to reassure the resident/patient that
the call has been activated.
Pendant Cord with light switch button
As above but designed to also accommodate low voltage light control switching.
Whereas all other cord pendants use the tip and sleeve of the tip-ring and sleeve
6.3mm jack, this version uses ring and sleeve (sleeve is common) for the purposes
of allowing the resident to switch the light on and off via the cord pendant.
Note. Although this model operates satisfactorily into a normally configured call-point
6.3mm socket, by triggering a normal alarm by the pressing of either button, to use
the yellow light switch button as intended it is important to note that a special version
of the bedside call-point will be required along with the associated isolated latching
relay device that processes the 240v AC switching function.
See SPC-H-LIGHT faceplate which must be used in conjunction with this cord
pendant if wishing to deploy the light switch function.
Page 46
15.5B A-K3820-2M
(‘Paddle’ Pressure
pad cord pendant)
15.6
A-MED-NC1R-01
(Hygienic Cord
Pendant)
Pressure pad (Paddle) Cord Pendant
Low profile pressure pad with large and slight pressure activation surface to suit
hand, arm or knee operation.
Single button Waterproof Silicon Cord Pendant
This sealed pendant is waterproof, suitable for dip sterilization, unbreakable and uses
anti bacterial and anti-fungal materials. Its ergonomic design suits left and right hand
grip and has a Braille imprint for visually impaired residents/patients.
47
69
68
99
72
103
Fitted with a 2M cord it suits all call points having the standard 6.3mm socket.
15.7
A-MED-NC2R-01
(Hygienic Cord
Pendant with Light
Switch)
Two button Waterproof Silicon Cord Pendant
Whereas all other cord pendants use the tip and sleeve of the tip-ring and sleeve
6.3mm jack, this version uses ring and sleeve (sleeve is common) for the purposes
of allowing the resident to switch the light on and off via the cord pendant.
Note. Although this model operates satisfactorily into a normally configured call-point
6.3mm socket, by triggering a normal alarm by the pressing of either button, to use
the yellow light switch button as intended it is important to note that a special version
of the bedside call-point will be required along with the associated isolated latching
relay device that processes the 240v AC switching function.
See SPC-H-LIGHT faceplate, which must be used in conjunction with this cord
pendant if wishing to deploy the light switch function.
Page 47
16. WIRELESS PENDANT APPLICATIONS FOR HOME & HOSTEL USE
Item
16.1
Model
A-PERS-APS-01
(Emergency-Call
phone & dialer
applications)
16.2
[GST Exempt & TGA Approved]
Description
Personal Emergency-Response System Pendant applications – 304Mhz
This is the traditional and most used application for personal pendants whereby
Smart-Caller phones and dialers can accept up to 48 pendants or wireless
transmitting devices.
A-CALLPOINT-APS- Wireless trigger of fixed location call-points - 304Mhz
This is the standard issue waterproof pendant (as supplied with the HP3 Blue-Phone
01
and HD4 Smart Dialler. In addition to its many other applications it provides a perfect
solution for those frail residents that need to effectively carry their call-point with them
(Necklace Wireless
when leaving the bed.
Pendant)
This (and other devices) may be used to directly trigger most versions of SmartCaller call-points as illustrated.
For those sites that do not have the benefit of Smart-Caller wireless trigger within
hard-wired call-points it is necessary to use the RDU-03 or -04 receivers that will plug
into ‘Other Brand’ call-points to allow wireless trigger operation.
See the range of RDU receivers in Section 12
Page 48
Image
W/Sale $
RSP $
Select price
from
elsewhere
Select price
from
elsewhere
Select price
from
elsewhere
Select price
from
elsewhere
17. CONNECTION ADAPTORS, EXTENSION LEADS & SIMILAR
Item
17.1
17.2
17.3
[GST Exempt & TGA Approved]
Model
A-ADAP-2
(Right Angle Low
Profile Dual
connection adaptor)
Description
Dual ‘in-line’ Low Profile 6.3mm Adaptor
Most Adaptors plug into the cal-point’s cord-pendant socket at 90 degrees from the
faceplate and are therefore subject to physical damage and will often damage the
socket within the call-point.
PLEASE SELECT
MODEL:ADAP-02-M =Mono
ADAP-02-S-B = Stereo
but wired as mono
ADAP-02-S-W = Stereo
and wired as stereo
Note. If in doubt – contact
us for assistance
The ADAP range of adaptors present a low profile from the call-point face-plate and
therefore are less subject to physical damage or damaging the call-point 6.3mm
socket.
A-ADAP-3
(Right Angle Low
Profile Triple
connection adaptor)
Triple ‘in-line’ Low Profile 6.3mm Adaptor
his range of dual and triple multiple in-line socket connections allows non protruding
connection to the call-point socket whilst also allowing connection of multiple devices.
For example the 3-way adaptor would accommodate the normal over-bed cord
pendant plus perhaps a floor mat located each site of the bed or a combination of
three separate devices as may be required from time to time. (3-way adaptor
illustrated)
A-GCORD-01-1M
Pt No 2643
Interconnecting cord with two 6.3mm male jacks to connect controller to callpoint socket
Will interconnect a Cura controller to the bedside call-point which uses a 6.3mm
socket. You may need to include a DA2-01 or one of the multi-way adaptors shown
below if the bedside socket is pre allocated for an over-bed pendant or other device.
17.4
A-GCORD-01-30CM As above but 30 cm in length. Perfect for wireless monitors.
17.5
A-PEND-EXT LEAD
[X]M
Extension Lead to extend pendant cord with 6.3mm jack to suite 6.3mm callpoint socket
Flexible extension leads with 6.3mm Socket and 6.3mm Plug.
Standard lengths 1M, 2M & 3M or to customer order. ([X] in part number to identify
required length.
Page 49
Image
As Above
W/Sale $
RSP $
23
33
33
47
21
32
11
16
1M 23
2M 25
3M 27
34
35
38
PART ‘G’ - DISPLAY & COMMUNICATION DEVICES
18. DISPLAY DEVICES, POCSAG & CURA PAGERS, ANNUNCIATORS & DECT PHONES
Item
18.1
Description
Model
A-PAGER-7950-VHF 2-Line Large screen pager
(4-line display &
This model POCSAG alphanumeric belt pager offers a good quality robust pager. It
vibrate pager both
includes holster, handbook and battery.
VHF & UHF versions)
Having eight addresses (capcodes) it has 4 beep tone cadences to identify the
incoming event and priority and includes flashing back-light and user selectable
vibrator function.
18.1A A-PAGER-7950-UHF
A heavy duty silicon holster and /or Bungee cord options are also available.
18.1B A-7950-SILICON
HOLSTER
18.2
N-BESTLITE-01-SS
(Single sided
Annunciator display)
(Addressable )
Also see WAC-07
Display controller
below.
Silicon/Rubber casing for 7950 pager. Comes in Black Red Green & Pink.
Limited colours in stock but can order prefered colours.
Image
W/Sale $
RSP $
150.00
220.00
16.00
25.00
515.00
736.00
553
791
Annunciator Display (Manufacturer’s Pt No SS-50-16 + Selected Options)
This new version Annunciator uses an attractive (improved) housing and is available
as a single or double-sided display with normal or high intensity LED displays
providing 50mm alphanumeric multicolor characters. It includes an internal fully
addressable audio amplifier with speaker and volume control and various mounting
hardware to suit wall or ceiling mounting.
It is capable of slow or fast flash plus slow scroll as may have been pre-determined
by programming the associated WAC-07 Annunciator Controller unit/s.
To minimize system cost it is usual to ceiling mount a single or dual display at 45
degree at each corridor intersection to allow viewing from within each corridor. Finish
is powder coated white with attractive styling.
Does not come with Power Pack. See Below.
18.3
N-BESTLITE-02-SS
(As above but to
replace a BetaBrite
display)
Non Addressable Annunciator Display to replace a BetaBrite Display
This is a retrofit solution. Do not purchase this model for new installations.
Page 50
18.3A N-BESTLITE-SS-50- Mini Single Sided Announciator Display - Half Size
Looks the same as full size only shorter. Casing measures 440mm in length.
08
(HALF SIZE
18.4
N-BESTLITE-01-DS
(Dual Annunciator
display)
357
511
801
1,145
557
797
29
40
49
69
Double Sided Annunciator Display (Manufacturer’s Pt No DS-50-16 + Selected
Options)
As above but with an identical display on each side of the panel. Intended for central
corridor ceiling mount. See above item for list of options and general notes.
Does not come with Power Pack
BESTLITE Annunciator display plug packs are available as separate. See Below.
18.4A N-BESTLITE-DS-50- Mini Double Sided Annunciator Display - Half size
Looks the same as full size only shorter. Casing measures 440mm
08
(HALF SIZE)
18.5
N-BESTLITE-PP1.5A
(Stand-alone power
source for BestLite
Display)
18.5A N-BESTLITE-PP3.5A
12v DC 1.5A Plug Pack to Suit Single Sided or Small Double Best-Lite
Annunciator Displays
A clean power source (i.e. one having no AC content to ground) is essential to avoid
corrupt displays, this is particularly important for large Annunciator installations. It
should also be recognized that a single display can draw up to 800mW when
displaying a full screen.
Using this approved plug-pack for each display overcomes the corrupt display
problems but does not provide a battery backed facility.
Using a good quality 12v battery backed power supply offer the alternative solution
however do no allow cable runs to exceed 30M if using CAT5 cabling. Contact SmartCaller Service department for detailed information and advice.
12v DC 3.5A Plug Pack to Suit Double Sided Best-Lite Annunciator Displays
Page 51
18.6
N-WAC-07
Accomodates both
Hardwired and RF
inputs.
Comes complete
with power pack and
antenna.
(Annunciator display
controller to drive up
to 16 independent
Annunciator Address
codes.)
(i.e. Can also have
multiple displays
sharing the same
Address Code)
18.7
N-BESTLITESOUND-GEN
Capable of both Wired and wireless Annunciator Controller
Superseding the previous WAC-01, WAC-02 and WAC-05 and WAC-06 and now
WAC-07-02 models. this new version.
This NEW WAC 07 is capable of both hardwired and wirless Annunciator
controlling. It comes complete with power pack and antenna. Although these
may not be required. Battery backed central 12v dc supply is preferable.
(WAC-07-01) has significantly more functionality and can communicate with (up to
16) BESTLITE Display ‘Address Codes’. On this basis it is possible to have multiple
paging groups with various duty shift call-traffic distribution requirements, all
controlled via a single WAC-07 controller.
597
854
121
173
NOTE. The limitation of 16 refers to the number of Address codes (similar to paging
cap codes) not to the number of Annunciator displays within the system – It is
perhaps therefore better to consider the 16 limitation as ‘zones’ where same zone
Annunciator displays would share the same address code/s.
In order to carry out the significant programming options, the WAC-07 includes a top
panel LCD display to assist in setting up the significant range of options that may be
used with each type of incoming call to each selected Display unit. In this respect it is
necessary to use the latest BESTLITE –01 Annunciator displays that are accordingly
addressable by the parent WAC-07 Controller.
Also see next item.
Addressable Sound Generator for Annunciator RS485 network
This fully capcode addressable and volume adjmustabls sound generator will
reproduce the sounds that are applkcable to annunciator displays that share the
same destinatio address that may be located on any of the RS485 lines that form the
network from the Starswitch or WAC-07 Controller.
Aconnecator is provided allowing its connection to your choice of 8 Ohm speaker
assembly.
The System Server controls day and night audio levels and priotity level tone type
and cadence are generated to match tose of th Bestlite Annunciators sharing the
network and destination address.
These auxiliary speaker unts are intended to improve overall display audio alerting
functions and are particularly applicable to untily rooms such a sth rLaundry where
call traffic may otherwise be missed.be
Page 52
18.8
N-STARSWITCH-01
(Essential item for
large Annunciator
display systems)
18.10
A-6020
Annunciator display RS485 Communications hub.
Connected to the WAC-07 Annunciator Controller this RS485 distribution hub
provides 5 separate RS485 drives from a single input. Each output provides one-way
communication designed for use with BESTLITE Annunciator displays where it
allows multiple display (loop through) connections for each of the 5 lines.
Each connection recognizes the need to maintain a balanced 120Ω twisted pair
connection and therefore allows any practical number of STARSWITCH units to be
used throughout the site.
A-4020
338
POA
POA
POA
POA
POA
POA
POA
POA
Spectralink 7620 Dect - Handset only - Battery Included
(For facilities with dect systems installed after mid 2013)
The Spectralink 7620 is an IP64 classified handset that combines durability with
maximum functionality. Designed for harsh industrial and manufacturing
environments. the 7620 features an alarm button enabling users to easily summon
assistance in the event of an emergency.
18.11
236
Spectralink 7420 - Handset only - Battery Included
(For existing sites where the dect system was installed before 2013)
The Spectralink 7420 is a robust, well designed and price competitive handset. It
meets demands for mobility around the workplace and is built for long-term
dependability in harsh environments.
18.12
A-60XXSILCASE
Silicon Case for 6020 handset
18.11
A-40XXSILCASE
Silicon Case for 4020 handset
18.14
A-60XXSCUSB
Single Charger with USB for 60XX series handset
This USB charger also used for programming
POA
POA
18.15
A-40XXSCUSB
Single Charger with USB for 40XX series handset
This USB charger also used for programming
POA
POA
18.16
A-60XXSC
Charger for 6020 handset - incl plug pack
POA
POA
18.17
A-40XXSC
Charger for 4020 handset - incl plug pack
POA
POA
18.18
A-60XXC
Belt Clip with connector for 6020
POA
POA
18.19
A-40XXC
Belt Clip with connector for 4020
POA
POA
Page 53
18.20
A-K-MAIN-RBS
Radio Base Station
18.21
A-KWS8000
Spectralink DECT Server 8000
Extremely scalable and flexible solution with combined analogue and SIP VoIP
interface
POA
POA
POA
POA
POA
POA
The Spectralink DECT Server 8000 is an extremely scalable solution which makes it
an ideal choice for both small and medium-sized businesses as well as large
enterprises.
A Spectralink DECT Server 8000 solution includes a number of interface cards: a
CPU card w/without link option, an analogue card with 8 or 16 lines, a VoIP interface
card with 32 simultaneous calls per card and a Base Station card that is able to
connect up to 8 KIRK Base Stations.
Each Spectralink DECT Server 8000 has room for 1 CPU card, up to 8 interface
cards-and up to 8 servers can be linked together.
When business grows, the Spectralink DECT Server 8000 can easily be expanded
without having to invest in a new solution. Furthermore, VoIP migration can be
carried out progessively over time—and without any additional software and
administration requirements involved.
18.22
A-KWS2500
Spectralink DECT Server 2500
Future-proof solution with combined analogue and SIP VoIP interface.
The Spectralink DECT Server 2500 solution is an ideal choice for small to mediumsized businesses. It is a flexible add-on solution that can be assembled to match the
exact needs of the individual customer. You get all the features and benefits of the
Spectralink DECT Server 8000 solution, but tailored to meet the needs of smaller
businesses.
The Spectralink DECT Server 2500 solution has room for one CPU card and three
interface cards: an analogue interface card with 8 or 16 lines, a VoIP interface card
with 32 simultaneous calls per card, and a Base Station card that connects up to 8
Spectralink DECT Base Stations.
It is possible to combine analogue and VoIP telephony in the Spectralink DECT
Server 2500 solution, which helps ensure easy migration into a full VoIP
solution—making it a future-proof investment. What’s more, it is future-proof in more
than one way. Should your business outgrow the Spectralink DECT Server 2500
solution, it can easily and inexpensively be upgraded to a Spectralink DECT Server
2500 solution.
Page 54
18.23
18.24
A-SMARTPHONE-01 WiFi System voice and data Communicator
With its 9cm full colour touch screen and using the site’s WiFi Network this Smart(Portable
Phone deploys the Android v2.2 operating system. With its dual SIM card capability it
communications via offers both standard wide area GSM network and local (LAN) WiFi operation, the
WLAN & GSM)
latter supporting WiFi 802.11b/g formats.
It also provides a camera function and supports bluetooth, Java and GPS operation.
Deploying an existing site-wide WLAN network the SmartPhone has the ability to
DEVELOPMENT
become an economical solution to providing Nursing/Carer Staff’ a prime
communication tool including the ability to recieve SMS (Paging calls) from the Nursecall computer head-end.
Note. Ensure that the nurse-call computer software also includes the appropriate
APS software module that aspect being the matter under development.
(Contact S/Caller before quoting)
Tablet Portable extension from & to nurse-call host computer
This portable tablet PC uses the Android 2.1 operating system and, using the site’s
(Bothway coms
WiFi facility will communicate with the host computer using 802.11b/n networking
between floor staff to infrastructure.
nurse-call computer) With its 10 inch colour TFT auto rotating touch screen the device supports standard
Microsoft Windows programs such as Word, Excel and Power Point and includes a
web browser, email facility plus an inbuilt microphone and stereo speaker function.
With the inclusion of a Smart-Caller Winwatch interface module the TABLET-PC-01
DEVELOPMENT
is ideal for the safe management of Resident/Patient medication, wound
management and incontinence reporting functions .
This product will provide powerfuol two-way communication and logging tool between
staff and the nurse-call host computer.
Note. Ensure that the nurse-call computer software also includes the appropriate
APS software module that aspect being the matter under development
(Contact S/Caller before quoting)
POA
POA
POA
POA
A-TABLET-PC-01
Page 55
18.25
N-DECT-SYSTEMS
18.26
N-DDU-01
(Door status display
panel)
KIRK DECT (GAP Compatible) Wireless Base Stations & Repeaters
A wide range of GAP compatible control systems, base stations and repeaters allow
(Range of various
both large and small systems to be configured to customer’s precise requirements.
Central equipment,
Refer to specific DECT data sheets for product descriptions, part numbers and
base stations and
product comparisons.
repeaters)
The illustrations show an IQL-WRX low cost GAP compatible repeater that will
extend coverage whilst also allowing a daisy-chain configuration for extended
coverage.
The second image shows a kirk/Polycom base station whilst the repeater has the
Request a quotation same appearance but is a cordless receiving device as distinct from the base station
being a traditional wireless access point WAP.
Any of the above DECT handsets and wrist versions will communicate with these
base stations and repeaters.
Door Display Unit
A mimic display board showing each protected door locations for a specific site with a
tricolor LED which will identify the status of the door providing that the door hardware
configuration (or a central access control system) is able to deliver the data from dry
contact activation for each event.
Typical events for doors that possess a controller (or from a central access control
system) include door open, door closed or door forced open or open too long DOTL).
Suitable drawings will be required before order is accepted.
The panel requires a 12v dc supply and cable connections are via rear mounted
quick release plugs and sockets. Any number of these panels may be connected in
parallel.
Page 56
2310
3003
PART ‘H’ - HARD-WIRED CALL-POINTS & SLAVE CLONES
19. ROOM AND COMMUNAL AREA CALL-POINTS
Item
19.1
Description
NEW H2 SERIES CALL POINT - ANTI FUNGLE/ANTI BACTERIAL - MASTER
Typical use: Over Bed
Includes Call, Cancel, Assist, wireless receiver and pendant socket. Piezo alert and
(Bedside master
back-lite call button and over door LED connection with fast flash for Assist.
call point)
Includes piezo alert A wireless receiver allows for the resident to have a wirelss pendant and fixed wirelss
call points in the room.
and wireless
accessories reviver)
Connection: Quick release RJ 45 and terminal block
It also incorporates two separate master call-point circuits known as CP1 and CP2,
This allows for either a seperate master or slave call points in the ensuite.
INCLUDES
A gasket is available but being over bed with a pendant jack a gasket is not required.
WIRELESS
Model
N-CPHW-H2-PC-04
PENDANT
ACTIVATION
Note. This product does not support light switching functions. To support pendants
with light switch see Part G Section 23 ‘Hospital equipment’.
H2 SERIES CALL POINTS HAVE HEART BEAT ENABLED Ref: DIP switch 4
Page 57
Image
W/Sale $
RSP $
1-9=77
102
10-49=73
96
50-100=70
93
100+=59
80
19.2
N-CPHW-H2-XX-04
Communal Call
Point
INCLUDES
WIRELESS
PENDANT
ACTIVATION
19.3
N-CPHW-H2-AS-04
(Assist call-points)
(Assist call-point
with Carer
duress/Assist
wireless trigger
capability)
Typical use: Communal Areas
Includes Call, Cancel, Assist, wireless receiver, piezo alert and back-lite call button
and over door LED connection with fast flash for Assist.
A wireless receiver allows for the resident to have a wirelss pendant and fixed wirelss
call points in the room.
Connection: Quick release RJ 45 and terminal block.
This allows for either a seperate master or slave call points.
A gasket is available for water proofing. If you prefer a quick release RJ and terminal
connection this call point with a gasket is ideal for beside the toilet in ensuites (lightly
wet areas).
As a communal call point the wireless receiver has the unique ability to also act as
a pin-point location call-point whereby any resident with any of our range of
pendant/wrist (PET) transmitters is able to trigger the call-point alarm function if in
the range of 12-15M.
Where a pendant is taught into a resident’s bedside call-point may also trigger the
communal area wireless call-point this is avoided by making a lock-out connection
between the communal call-point/s and adjacent (within range) room call-points. See
Lock-out PCB in Central Equipment, Section 27.
This product does not support light switching functions. See Part G ‘Hospital
equipment’
Typical use: Where a dedicated ASSIST button is specified.
Includes Assist, Cancel, wireless receiver, piezo alert and back-lite Assist button.
A wireless receiver allows for remote activation and fixed wirelss Assist points in the
facinity and over door LED connection
Connection: Quick release RJ 45 and also terminal block.
A gasket is available for waterproofing. (Also available with the PCB that allows for
resin to be applied for total waterproofing)
Note: All standard master call points and two button slave clones have the ability to
generate an Assist alarm by pressing the Call and Cancel at the simultaneously. The
Assist call point is used when a dedicated Assist call point is specified.
Page 58
INCLUDES WIRELESS
PENDANT ACTIVATION
1-9=75
100
10-49=71
94
50-100=68
90
100+=57
78
1-9=75
10+=71
100
94
INCLUDES
WIRELESS PENDANT
ACTIVATION
19.4
N-CPHW-H2-EMG-01 EMERGENCY CALL POINT "H2" SERIES
Emergency Call-point Standard flush mount ‘H’ series with call and cancel
Unlike the mushroom head and similar large button Emergency-call call-points below
this version uses electronic latch and includes the standard “h” series wireless
receiver for remote activation of an emergency.
This model also includes a wireless receiver to allow remote activation from a nearby
wireless pendant or other triggering device such as may be triggered from intensive
care apparatus having detected a Patient’s life threatening situation.
1-9=75
10+=71
100
94
1-9=75
100
10+=71
94
1-9=79
10-100=75
10+=70
110
105
98
19.5
N-CPHW -H2-NP-01
(Nurse presence
call-point)
Typical use: Where a NURSE PRESENCE button is specified
Includes Nurse Presense, Cancel, wireless receiver, piezo alert and back-lite Assist
button and over door LED connection.
A wireless receiver allows for remote activation and fixed wirelss Nurse Presense
points in the facinity.
Connection: Quick release RJ 45 and terminal block.
A gasket is available for waterproofing.
(Also available with the PCB that allows for resin to be applied for total waterproofing)
19.6
N-CPHW-H2-APWP- NEW H2 SERIES CALL POINT - ANTI FUNGLE/ANTI BACTERIAL 01
WATERPROOF
Typical Use: Ensuites and communal bathrooms/toilets
(Master Call-point,
Master call-point, all purpose WATERPROOF comes complete with gasket and can
with waterproofing
be sealed with resin at an extra cost)
gasket and ability to For resin water proofing add "R" to end of part number (cost $6 extra)
apply resin sealant)
Connection: Via flying lead with scotch locks. Scotch locks provided.
For ensuites that are not critically wet you can alternatively use the CPHW-H2-XX-01
and a gasket. The CPHW-H2-XX-01 allows for a quick release RJ connection and
sufficient waterproofing when the gasket is also used.
Page 59
19.7
N-CPHW-APWP-01
(Master Call-point
with waterproofing
gasket)
This model
superceded
Master call-point, all purpose, Hooded waterproof
Single gang all-purpose wet/dry area hard-wired master call-point, waterproof to IP65
rating.
Note. It is necessary to run a silicon seal around the top and side edges of the callpoint to ensure waterproofing. Product guarantee is void if water damage has
occurred without evidence of natural cure silicon seal.
1-9=54
10-49=48
50-100=45
70
67
62
SEE
NOTE
SEE
NOTE
7
9
4.5
6.5
See Above
LIMITED STOCK
19.8
19.8
19.9
WATERPROOFING
'H2' SERIES
APPLY RESIN = R
WATER PROOFING 'H2' SERIES CALL POINTS - Gaskets and Resin Sealing
All H2 series call points (except overbed with Jack) are waterproof from the front.
H2 Waterproof call points have flying leads and are supplied with scotch locks to
allow the connection to be inside the wall and away from the call point.
Waterproof call points are always supplied with a gasket.
Waterproof call points can be further waterproofed by sealing the electonics in resin
for a further cost of $6 per point. Recommended for true wet areas ie showers and
steam rooms. For resin encapsulation include an R on the end of the part number ie
CPHW-H2-APWP-01-R
Applying silicon seal around the top and side edges of a call point offers water
proofing.
For not critically wet areas you may use a standard H2 call point and also use a
gasket. Ideal for beside the toliet in an ensuit. Standard call points have RJ and
terminal block connections.
Ceiling pull cords are a good option for wet extreme wet areas.
RESIN WATER PROOFING FOR NURSE CALL POINTS
H Series waterproof call points are made with a modified PCB that allows for the
PCB to be sealed with resin, totally waterproofing the call point. Applying resin is an
extra cost and is only required for call points in very wet areas such as showers and
steam rooms.
Apply -R to end of
Call Point Part
Number ie
N-CPHW-H2-WP-01N-GASKET- H2
GASKET TO FIT ALL H2 MODEL CALL POINTS
Typical use: To provide water proofing to H2 call points. This is ideal for beside the
toilet or damp areas.
For complete water proofing for shower recessed and steam rooms use the CPHWH2-WP-01-R (R=with resin encapulation of PCB) Waterproof H2 call points come
with gaskets. If you want to water proof a standard call point that has a RJ
connection for a marginally wet area the gasket is sufficient and/or also use silicon if
in doubt.
Page 60
RESIN
19.10. N-PSCP-H2-WP-01
(Comes with gasket
and the ability to
encapsulate the PCB
with a resin filler)
NEW H2 SERIES PRIME SLAVE CALL POINT - ANTI FUNGLE/ANTI BACTERIAL
Typical use: When resin is applied this is completely waterproof making it ideal
for extreme wet areas such as showers and steam rooms. With just the gasket
it is ideal for general ensuite use.
Comes complete with gasket.
Connection: Via scotch locks on a flying lead. Scotch locks provided.
For resin waterproofing add R end of the part number ie PSCP-H2-WP-01-R
1-9=42
10+=38
60
54
77
102
79
105
120
170
125
125
130
120
172
172
179
169
All two button slaves mimic the master call point, so call cancel and assist are
available. Slaves do not have wireless or piezo.
Where resin encapulation is not required and you prefer terminal block connection
the PSCP-H2-XX-01 with a gasket would offer sufficient water proofing.
19.11.
H SERIES CALL POINTS - REPLACED BY H2 RANGE - OBSOLETE BUT STILL
AVAILABLE
19.12. N-CPHW-H-PC-04
CPHW-H-PC (OBSOLETE)
Bedside hard-wired call-point + pendant socket, piezo audio alert & inbuilt Wireless
Discontinued Model Receiver. See H2 Series.
All 'H' Series
WHILST STOCKS LAST
discontinued. See
'H2' Series being
fully compatible
19.13. N-CPHW-H-XX-04
As above but with no pendant cord jack
Discontinued Model WHILST STOCKS LAST
PRESTIGE CALL POINTS - LARGE BUTTON - OBSOLETE BUT STILL
AVAILABLE
19.19. N-CPHW-4M-PC-01
(Prestige Big Button
Call-Points)
19.20.
19.19.
19.21
19.22
.
N-CPHW-4M-PC-02
N-CPHW-4M-PC-05
N-CPHW-4M-PC-06
N-CPHW-3M-GP-01
Big-Button Master call-point, over-bed
Prestige - 4 module call-point with call, cancel, assist LED and 6.3mm cord pendant
jack.
This range of products is continued in support of existing systems where these bigbutton ‘Prestige’ assemblies were originally installed and has been superceeded by
the H2 silicon button range.
As above but with piezo sound alert
As version 01 but with wireless Rx
As version 02 but with wireless RX
Big-Button Master call-point, communal area (Excludes 6.3mm Socket)
Page 61
As Above
As Above
As Above
As Above
20.
Item
20.1
Model
N-PSCP-H2-XX-01
(2-button Clone
Slave) - No Gasket
supplied
HARD-WIRED SLAVE CALL-POINTS & ACCESSORY CONNECTION PLATES
Description
NEW H2 SERIES PRIME SLAVE CALL POINT - ANTI FUNGLE/ANTI BACTERIAL
General Purpose Prime Slave call point
Typical use: Ensuites or anywhere there is a master call point and another call point
is required in the same facinity. It may be water prrofed by using a gasket which
makes it idea for beside the toilet.
For extreme wet areas see PSCP-H2-WP-01-R R = with resin encapulation.
Connection is by a terminal block.
Image
W/Sale $
RSP $
1-9=44
10+=40
60
55
1-9=44
10+=40
60
55
1-9=50
10+=43
63
58
All two button slaves mimic the master call point, so Call, Cancel and Assist are
20.2
20.3
N-PSCP-H2-WP-01
NEW H2 SERIES PRIME CALL POINT - ANTI FUNGLE/ANTI BACTERIAL
Typical use: When resin is applied this is completely waterproof making it ideal for
(Comes with gasket extreme wet areas such as showers and steam rooms. With just the gasket it is ideal
and the ability to
for general ensuite use.
encapsulate the PCB Comes complete with gasket.
with a resin filler)
Connection: Via Scotch Locks on a flying lead. Scotch locks provided. This call
point can be sealed by a resin backing for maximum waterproofing. Suggested use
for showers and true wet areas.
For resin waterproofing add R end of the part number ie PSCP-H2-WP-01-R
All two button slaves mimic the master call point, so call cancel and assist are
Where resin encapulation is not required and you prefer terminal block connection
the PSCP-H2-XX-01 with a gasket would offer sufficient water proofing.
N-PSCP-H2-PC-01
NEW H2 SERIES CALL POINT - ANTI FUNGLE/ANTI BACTERIAL
(2-button clone Slave Prime slave call point with 6.3mm cord pendant socket
with 6.3mm socket)
Typical Use: This is a convenient method of providing two fully functional cordpendant type call-point locations within the same living area where, for example, a
low cost slave call-point could be located at the room’s chair position also allowing
connection of the cord pendant.
Connection is via terminal block
All two button slaves mimic the master call point, so call, cancel and assist are
Page 62
20.5
N-PSCP-GPWP-01
HOODED PRIME SLAVE CALL POINT WITH TWO BUTTON FUNCTION
Typical use: General purpose and very wet areas provided the surronds are sealed
(supplied with foam with silicon.
Connection is by terminal block. Resin encapsulation is not available on this call point.
gasket)
All two button slaves mimic the master call point, so Call, Cancel and Assist are
20.6
N-SCP-GPWP-01
20.6A N-CPHW-EMG-01
CALL ONLY SLAVE CALL POINT
AS ABOVE BUT WITH
Typical use: For where a call only call point is specified. Ideal for front door bells.
ONE CALL ONLY
Connection is by terminal block. Resin encapsulation is not available on this call point.
BUTTON
All slave call point mimic the master call point.
43
41
39
62
59
55
50
53
50
66
40
53
MUSHROOM HEAD EMERGENCY WIRELESS CALL POINT - SURFACE
MOUNTED
As above but mounted in within a 45mm mounting box HPM239
20.6C N-CPHW-EMG-03
59
55
50
MUSHROOM HEAD EMERGENCY CALL POINT - FLUSH MOUNTING
Mechanically latching call point with a twist release cancel action.
40mm diameter red button and latching LED indicator.
The assembly protrudes to a depth of 40mm into the plaster wall.
The Emergency Label can be changed to suit other applications as required.
20.6B N-CPHW-EMG-02
1-9=42
10-49=40
50+=38
A FLUSH MOUNTING BUTTON WITH A BUTTON PROTECTION SURROUND
This model uses the same mechanism as the CPR304-EMG-01 & 02 but the
assembly is set into the button surtton can not be accidently pressed.
The button diameter is 20mm and the total button assembly extrends 20mm from the
face plate surface.
Page 63
20.6D N-CPHW-EMG-04
AS ABOUVE BUT SURFACE MOUNT WITH A 45MM MOUNTING BOX HPM 393
Overall dimewntions are 115L x 70W x52H
20.7
N-SCP-H1G-CM-01
(Ceiling mount slave
call-point)
Ceiling mounted slave call-point –Hard-wired systems
As used within hard-wired systems (not HP2 Phones), this is a standard commercial
quality HPM product modified to include a LED & 10Kg break strain link.
50
66
1-9=50
10+=47
68
66
1-9=29
10+=25
37
35
It is a popular solution to having a call-point in the shower recess, however, in higher
care situations where the nurse/carer is required to assist the resident serious
thought should be given to the alternative use of the above waterproof version wall
mounted call-points fitted at 600-650 mm AFL as the shower recess is the most likely
location that the staff will call for assistance which cannot be provided by a piece of
string connected to a ceiling call-point assembly.
20.8
N-SPC-1M-PC
(Faceplate with
6.3mm socket)
Accessory faceplate with 6.3mm Socket
Prestige surface mount faceplate containing a 6.3mm socket to suit a cord pendant,
Floor mat or similar device.
Sometimes the client will require you to install this plate near the resident’s table,
verandah or similar daytime resting location, which then allows the bedside cord
pendant to be used at either location. This is better than supplying a 5M cord pendant
which is a ‘falls hazard’ and should be avoided.
A wireless pendant triggering a wireless receiver within the bedside call-point is
perhaps a better, but higher priced solution.
Note See also Dementia products where this item also has on-off switch with
Arm/disarmed LED
Page 64
20.9
N-CONN-02
(Wall socket for
sensors)
RJ45 socket on Prestige wall plate.
RJ45 socket on Prestige wall plate. For use with Smartlead-03, 04 & 05 (Curly-cord
versions).
1-9=34
10+=31
45
42
1-9=48
1-+=45
68
65
44
39
55
53
(Use this essential
Note. Wiring behind the faceplate may vary depending on the choice of Smartlead
item [or listed
and sensors to be used. There are various Smart-Caller and third party versions and
alternative] for new
new products from time to time.
standard Installations)
It is wise to contact Smart-Caller Engineering support to ensure appropriate plate and
socket wiring arrangements.
Note. A Smartlead is required for connection between this wall socket and the floor
mat or similar connected bed exit accessory. The Smart-Lead should be offered
along with the sensor accessory and not as part of the initial installation.
20.10
N-CONN-03
(Wall socket for
passive and active
bedside accessories)
RJ45 Socket on Prestige wall plate with local arm/disarm switch and LED
This ‘universal’ bedside accessories socket provides simple open/closing contact
connections along with 12v supply for use with accessories that require power and
plug-packs are to be avoided.
It provides a local arm/disarm switch for accessories with LED indicator to allow
attending carers to disable accessories when attending residents.
20.11
N-CANCEL-SW-01
(Room Cancel
Switch)
Room Cancel Switch
Some customers insist on having a room cancel button within the room at the door
location. Ensuring that we maintain an ‘homelike environment’ this attractive Prestige
type switch will be supplied as a momentary rocker switch configuration which is
connected to the remote cancel terminal of the bedside master call-point where it
also derives its LED drive to identify that an active call exists. It is the same LED
drive circuit that would terminate on the over-door LED assembly (if used).
Page 65
PART ‘I’ – HARD-WIRED DEMENTIA ROOM EQUIPMENT (Excluding nurse-call)
21. HARD-WIRED DEMENTIA ROOM EQUIPMENT (Excluding standard nurse-call items & bed exit sensors)
Item
21.1
Model
N-DEMCON-IDFBOX-01
(Dementia control
unit Cabinet and
room IDF)
(This is an essential
item for dementia
room cabling)
(Also See low cost
MINDER-01 new
Alternative (Item
21.21)
21.2
21.5
Description
Room Dementia Controller Cabinet and IDF Connection Bus for hard-wired
system
The trend with new aged care establishments is to plan for future progressive fit-off
of room dementia management facilities within the initial room cabling infrastructure
and to fit the more expensive active equipment components in future on a ‘need be’
basis.
This low cost cabinet contains the punch down terminations to suit the total room,
ensuite and corridor interconnections allowing a ‘plug-and-Play’ circuit board to be
plugged in at some future date when full or partial dementia management becomes
necessary.
W/Sale $
RSP $
1-9=65
10+=60
85
80
1-9=170
10+=160
240
228
27
38
The alternative DEMRAD-IDF version is identical but includes a wireless antenna for
wireless communication in lieu of, or in combination with hard-wired connections.
N-DEMCON-PCB-01 DEMCON ‘plug-in’ Circuit Board
This circuit (PCB) simply plugs into the socket located under the DEMRAD-IDF-01
(Plug & Play
cabinet and all connected functions become immediately active. There are no
Dementia Room
adjustments or other requirements necessary to enable the facility providing that all
Controller Circuit
sensor devices and the corridor control panel are correctly installed.
board)
The DEMCON controls the Bed exit sensor (or floor mat), Light switching, Door
Wander PIR, Room Space PIR for pacing detection, Ensuite overstay PIR.
(This is an essential Normal nurse-call functions such as bedside and ensuite call-points operate
item when deploying independently of the DEMCON PCB and are not therefore dependent on the PCB
Dementia facilities
being plugged in.
within a room)
This suits DEMCON-IDF-BOX-01 above.
N-PIR-SA-01
(Stand-Alone PIR)
Image
Separate PIR Less Bracket and Cable Assembly
For direct wall mounting and connection behind the plaster wall to the CONN-02 or
CONN-03 (if used but reacommended)
Page 66
21.5A
N-PIR-BRACKET
(Separate Brackets
for Spare or
additional use)
21.6
N-DEMRAD-01
(Portable Dementia
room
communications
system)
(Remember to
select antenna)
21.7
Bracket for Bed-Exit PIR
For prelocating to suit alternate locations where cable length allows or if wireless
version used.
care room.
Arm/disarm "Smart-Key" flush panel
"Smart-Key" corridor mounting control panel with bed exit & ensuite selectors - Flush
mount version
This unit is located outside of the room so that the room dementia system may be
disarmed without tripping the door PIR. I has two pen-tip rotary switches to select the
(Use this essential
necessary out-of-bed and overdue from ensuite intervals prior to an alarm being
item for new
standard installations) processed.
N-ARMSW-01
(Corridor control
panel)
It also possesses a common key to arm and disarm the room’s facility and includes
LED indication of room status.
Page 67
8
15
1-9=329
10+POA
420
1-9=115
10+=106
151
141
21.8
N-OD-LED-03-RJ
(Over-door LED
Assembly)
(Use this
recommended item
for new standard
installations)
Over-Door LED with three LEDs
This three-LED assembly includes Red, Yellow and Green LEDs to detect (a) Out of
bed/Wanderer (b) Nurse-Call/Assist and (c) Bed-wet respectively. Superbright LEDs
are used in a diffuser cap providing high intensity viewing up to 20M.
Clients often prefer not to have over-door LED assemblies, however, the installation
of these inconspicuous faceplate assemblies is recommended for two reasons as
follows:-.
These units should be ceiling mounted in order that a Carer can glance along the
corridor to detect any non-cancelled alarm conditions. It also draws immediate
attention to a fast flashing ‘Nurse Assist” condition within the adjacent room.
Over-door lights are also recommended under the standards as it provides a
‘Lifeboat” facility should the central equipment fail.
N-OD-LED-01-RJ
OVERDOOR LED WITH SINGLE YELLOW LED
NEW ITEM
21.9
21.10. N-OD-LED-02-RJ
AS ABOVE BUT WITH
SINGLE YELLOW
OVERDOOR LED WITH DUAL LEDS - Please specify required colours Yellow
Green or Red
21.11. N-PIR-CURT-01
(Door curtain PIR)
Door Curtain PIR
This new version is flush mounting and is to be located top-center of the doorway
preferably on the inside of the door within the room as it is possible to experience
false calls if the sensor located on the passage side of the door.
(Use this essential
If the room’s main entrance is also close to the resident’s entry to their ensuite care
item for new
standard installations) should be taken to ensure that a resident entering or leaving the ensuite does not
trigger the PIR. In this case it would be preferable to mount the PIR on the outside of
the door in an orientation that minimizes false calls.
Similarly the PIR may be mounted across the inside of the door if such an
arrangement is likely to minimize false calls, i.e. providing horizontal view across an
open door.
Page 68
AS ABOVE BUT WITH
TWO LEDS
1-9=34
10+30
44
40
1-9=27
10+=22
39
1-9=30
10+=26
41
37
1-9=35
10+=32
45
42
21.12. N-TLC-360
(Room space PIR)
(Use this
recommended item
for new standard
installations)
Room Space PIR with 360 degree coverage
This PIR has two functions the prime function being the detection of movement within
the room to allow ‘Handover” and ‘Hand back’ of the resident entering and emerging
from the ensuite. The handover/Hand back process controls the setting in the
corridor control panel for the ensuite ‘overstay’.
Its second function is to operate as an out-of-bed sensor, however this technique is
unreliable as it depends on continued movement of the resident whereas the resident
may have fallen.
A carefully placed Model MR-90 being a 90-degree PIR is also suitable for this
application if preferred. It is essential that the field of view of this PIR shall not clash
with that located in the ensuite otherwise the handover and Hand back functions are
subject to malfunction. Failure to install a room space PIR will mean that Ensuite
monitoring will be limited to detecting entry only and the ‘overstay’ function will not be
available.
21.13. N-MR-90
(Ensuite PIR)
Ensuite PIR with 90 degree coverage
This unit will either send an ensuite entry alert or send an ensuite overstay alarm
depending on the setting of the corridor control panel. The latter facility also depends
on the fitting of a room space detector as described above.
(Use this essential
It should be located so that it does not extend its view into the main room or entrance
item for new
standard installations) to the main room otherwise it will generate false calls.
21.14. N-CONN-02
(Wall socket for
sensors)
(This is an essential
item if using a Floor
mat as the bed exit
sensor)
Floor Mat Connector RJ45 socket on Prestige wall plate.
This unit allows the connection of a Floor mat which is pre-wired within the room to
the Demcon controller location. If nothing is connected to this socket the Demcon
Controller recognizes this situation and then allows the room PIR to act as a Pacing
sensor.
1-9=47
10+=42
68
60
1-9=48
10+=42
67
63
1-9=32
10+=26
42
37
1-9=49
10+=47
59
57
If using a ‘within’ bed or chair sensor (which operates on the release of pressure)
then the CONN-02 is not applicable and the BME-DEM-02 Bedside controller should
be used (see next item)
21.15. N-CONN-03
RJ45 Socket on Prestige wall plate with local arm/disarm switch and
LED
(Wall socket for
This ‘universal’ bedside accessories socket provides simple open/closing
passive and active
contact connections along with 12v supply for use with accessories that
bedside accessories)
require power and plug-packs are to be avoided.
It provides a local arm/disarm switch for accessories with LED indicator to
allow attending carers to disable accessories when attending residents.
Page 69
21.16. A-MAXI-MAT-DEM
Pt No 2633-DEM
(Pressure Floor Mat)
12 month pro-rata
warranty
Large Floor Pressure mat hard-wired with RJ45 Plug to suite CONN-02 plate
Designed to immediately alert that a person had exited the bed. It is a large (1200 x
600mm) pressure mat being warm underfoot. It is waterproof and washable using a
low profile, non-slip material. 12 month pro-rata warranty applies.
Note The connector is configured to suite the CONN-02 (and CONN-03) bed
accessory connection plate as used within a dementia specific room..
Note. Must use BME-DEM controller to connect to the CONN-02 wall plate – See
below
21.17. A-MAXI-MAT-DEMx8 As above but in single packs of 8 units per pack (1 year warranty)
(Bulk supply)
Due to the cost and complexity of dispatch packing we recommend purchasing the 8pack standard stock package.
12 month pro-rata
warranty
21.18. A-BPLB-01-DEM
Pt No 2626-DEM
(Within-bed Bed Exit
Sensor)
12 month pro-rata
warranty
145
226
958
1429
79
116
56
84
As Above
Bed Exit Pressure Pad – hard-wired (1 year warranty)
Measuring 760mm x 510mm the low cost BPLB-01 pad is classified as a
consumable item having a 12 month life expectancy and warranty. 30 day and 3
month warranty versions also exist for use in infectious and palliative applications.
Note. Must use BME-DEM controller to connect to the CONN-02 wall plate – See
below
21.19. A-BPSC-01-DEM
Pt No 2628-DEM
(Chair Exit pad)
12 month pro-rata
warranty
Chair Exit Pad – Hard-wired (1 Year Warranty)
Where a chair is in close proximity to a call-point this chair exit sensor can be hardwired to its BME-DEM-CON. It will trigger an alarm along with audible tone in the
event of the resident leaving or falling from the chair.
With wheel chairs it is more practical to use a wireless connection to the exit pad and
there are a number of scenarios that will allow a chair exit alarm to be identified along
with the location of the event. These options include teaching the chair pad
transmitter into the resident’s bedside call-point and/or teaching it into one or more
site-wide Safe-T-Net receivers.
Page 70
21.20. N-BME-DEMCONTLR-01
(To introduce delay
before actiating
alarm)
21.21
N-MINDER-01
(Low cost dementia
room controller and
door station panell push button activated)
Bed and/or Chair Exit Sensor Controller (Also suits Floor mat but not normally
required)
This low cost stand-alone bedside controller is designed to suit the Cura range of
Bed and Chair exit sensors described in Section 4 pages 14 to 16.
This model replaced the need for a CONN-02 or CONN-03 as it includes the
necessary logic circuits to provide control of local audio alert, on-off arm/disarm
switch and local reset.
It would normally be connected to the bedside call-point from within the wall sheeting
(as also applies to the CONN -02 but in this case must derive power from the callpoint and is therefore an active connection.
Note, This unit will also accommodate a floor mat should various types of floor, bed
and chair sensors be used from time to time.
Dementia Room low cost corridor controller with push button
Located in the corridor this modified H2 Series call-point provides the arm and
disarm plus call traffic processing for bed exit and door exit sensors. It is suitable for
use with any sensor device that offers a momentary closing contact from a N/O
contact device. See Minder datasheet for full details and wiring diagram.
Simply connect the bed exit and door exit Sensors and the sensors will trigger the
normal alarm (OOB Out of bed) and Assist (Wanderer) Ademco strings to the site's
Winwatch equipped Server either via Slave Controllers or BlueLine-IP Nodes.
21.22
N-MINDER-02
(Low cost dementia
room controller and
door station panel key switch activated)
69
99.5
1-9=95
10+=86
136
1-9=95
10+=90
137
Dementia Room low cost corridor controller with Key Switch
Alternative to push button activation
Page 71
PART ‘J’ – IP, DECT & DEMRAD NURSE-CALL ROOM CONTROLLERS
22. HARD-WIRED & PORTABLE ROOM CONTROLLER & PORTABLE DEMENTIA KIT SOLUTIONS)
Item
22.1
Model
N-CARECOM-IP-01
(IP Room Controller)
Latest Technology
solutions
Description
IP NURSE-CALL Room controller –Subnet connection with Display, POE &
speech
This wall-mounting unit has alarm, cancel and nurse-presence buttons and will
accommodate 2 identifiable additional inputs to accommodate over-bed pendant
and/or various fixed or wireless trigger devices. It also accommodates a display with
multilevel alarm capability.
In addition to communicating into the nurse-call system head end via a sub-net LAN
path, it has two N/O independent outputs allowing such devices as corridor over-door
lights to operate.
Using SIP technology CARECOM-IP will also accommodate high quality full duplex
two way auto-answer voice communication between the resident/patient and the
responding carer. Should the nominated carer not accept the call, it will revert to a
preplanned ‘buddy’ call arrangement.
The unit is powered via POE connection at the nearest network switch therefore no
special arrangements are necessary and battery backed supply would be ensured via
the POE connection at that point.
Constant polling ensures supervision of continuity of service and an inexpensive 3CX
soft switch would normally provide the voice and message handling requirements
deploying a high quality of service VoIP protocol.
Page 72
Image
W/Sale $
RSP $
Est 400
Est 532
22.2
N-CARECOM-DECT DECT NURSE-CALL Room Controller; cordless and transportable with speech
This wall-mounting unit has alarm, cancel and nurse-presence buttons and will
accommodate 2 identifiable additional inputs to accommodate over-bed pendant
(DECT Room
and/or various fixed or wireless trigger devices.
Controller)
In addition to communicating into the nurse-call system head end via the GAP
compatible DECT wireless infrastructure it has two N/O independent outputs allowing
such devices as corridor over-door lights to operate.
Using SIP technology CARECOM-DECT will also accommodate high quality full
duplex two way auto-answer voice communication between the resident/patient and
the responding carer. Should the nominated carer not accept the call, it will revert to
Latest Technology a preplanned ‘buddy’ call arrangement.
The unit is powered via a 12v or 24v nurse-call source of plug-pack and a 10 hour
solutions
battery backed power source in inbuilt.
A special wall-mounting bracket is capable of powering the unit in new installations
where cabling work is easily available.
The prime benefit of this product is that it fits within the DECT wireless infrastructure
and is particularly geared to the Polycom/Kirk/Multitone format where additional
enhancements have been catered for.
Unlike the CARECOM-IP version the CARECOM-DECT version is cordless and
therefore both flexible and portable. Both versions can be used within a single
system that uses DECT portable communications.
The basic model is CARECOM-DECT-01;Being DECT Basic and CARECOM-DECT02 (being Enhanced)
Page 73
Est 316
Est 420
22.3
N-DEMRAD-01
(Portable Dementia
room
communications
system)
(Remember to
select antenna)
care room.
Page 74
1-9=329
10+=POA
420
PART ‘K’ – HOSPITAL SPECIFIC ITEMS (Excluding products from other sections)
23. HOSPITAL SPECIFIC EQUIPMENT – (additional to standard hard-wired, wireless and display products)
Item
23.1
Model
N-PEH-01
(Entertainment
Handset)
Description
Patient Entertainment handset
Unlike aged care facilities where residents are inclined to use personal Infrared
controllers, the entertainment handset with nurse-call, light switch and TV controls is
commonly used within Hospital wards. Hygienic design concepts are now mandatory
and the new PEH-01 handset adequately meets this requirement. A headset socket
with( waterproofing grommet) is provided .
Image
W/Sale $
RSP $
202
289
36
49
POA
POA
This new product has a robust anti-fungal construction with built-in speaker and
rotating shutter. The design is rated to IP68. In this respect the handset’s cover is a
two-piece design made of high impact but flexible polycarbonate. The joint for the
covers is encapsulated with a one piece rubber gasket to prevent any water
ingression.
23.2
23.3
N-PEH-D25-SKT-01
(Entertainment
handset socket)
N-BEDH-PANEL-01
(Custom Bedhead
comms panels)
Patient Entertainment Handset Socket plus alternative Bedhead combinations
The handset socket may be a standalone matching faceplate or combined in a dual,
triple or similar standard Clipsal surround.
The price of this socket is shown without the rear mounting associated control PCB
circuit
Also illustrated is combination of bedhead call-point, 6.3mm cord pendant socket to
accommodate light switch control plus a panel that includes an entertainment
handset socket assembly. Other assemblies may also be included within a Clipsal
multi-gang assembly such as power switch and socket, a data or telephone
connection or other similar requirements.
Standard bed-head panel.
This unit is provided with Emergency, Resident, Assist, cancel call-point functions
plus 6.3mm and Entertainment handset socket, the latter with TV, Light, and nursecall control circuit modules, which are professionally mounted behind the panel along
with quick release connectors.
See Data Sheet for full details and illustration of ‘behind panel’ circuit modules and
connections. The price is based on the use of 2mm powder coated aluminium
material, however Stainless steel option is available.
Note. Various socket options are available and we have not yet selected our
preference.
Page 75
23.4
N-SPC-H-LIGHT
(Faceplate with
6.3mm socket and
isolation 240v ac
switching relay for
light control)
Cord Pendant Light switch faceplate
This Light-switch faceplate is used as an optional module beside a normal bedside
call-point assembly. They would typically share a dual housing surround along with a
common area ‘H’ series Master call point. The SPC-H-LIGHT-01 unit is used to
separately accommodate the 951027-2 and MED-NC2R cord pendants, which have
a momentary contact light switch.
1-9=69
10+=67
99.5
96
81
116
As it is pointless (in fact dangerous) to use a standard bedside call-point with its
6.3mm socket alongside a companion SPC-H-LIGHT unit it is therefore essential to
select one of the common area call-points that does not have such a socket. Make
sure that you add the call-point to the SPC-H-LIGHT Assembly price.
The SPC-H-LIGHT unit derives its 12v supply from the adjacent ‘H’ series call-point
and similarly delivers the cord pendant nurse-call alarm to the appropriate terminals
of the master call-point.
The light switch isolation relay included within the SPC-H-LIGHT unit will deliver a
latched 12v dc supply when the pendant cord light switch is pressed and
correspondingly will unlatch the 12v supply when the cord pendant’s Light switch
button is again pressed.
The left to right orientation of the Master call-point and its companion SPC-H-LIGHT
light switch faceplates may be configured to suit specific requirements.
Note. Price includes the dual surround but does not include the CPHW-H-XX04 call-point as is illustrated.
23.5
N-OD-MULTI-LED-01 Hospital overdoor light Assembly
With 6 superbright coloured LEDs this specially designed triangular transparent
(Hospital Overdoor
assembly provides an amplified 180 degree clear view of all or any of the light being
Light Assembly)
emitted from the LEDs.
Standard package is 3 colour long life LEDs including Red, Green and Yellow.
Single or two LED colour operation is possible via selective connection
arrangements.
This low cost highly effective light assembly has a modern appearance to suit any
Page 76
23.6
N-NURSE STN-15
Nurse or work station with or without touch screen
This comprises a combined screen with inbuilt Server qualty integral PC.
(Active Nurse-Station
terminal)
With password protection it allows a nurse-station to have totala access to
the total Winwatch nurse-call program (as may be limited by password
access) for viewing active and logged incoming and outgoing call traffic in
addition to generating outgoing call-traffic, viewing care-plan and other
instructions.
In essence it is a clone of the head-end Nurse-call Winwatch and
Winmonitor programs with limited access to disallow editing of database or
other essential parameters.
Page 77
POA
POA
PART ‘L’ – CENTRAL CONTROL EQUIPMENT
24.
Item
24.1
Model
N-SMARTCOM-04
(Industrial quality
embedded software
computer)
Don’t forget to add
next item &
Software modules
CENTRAL EQUIPMENT FOR TELEPHONE, WIRELESS, HARD-WIRED & IP SYSTEMS
Description
Compact solid state computer with embedded XP-Pro operating system
With embedded software and no moving parts along with the ability to power this
server quality computer system from the nurse-call central battery backed power
supply this ‘Application Ready’ computer offers the ultimate in operational reliability
and flexibility. It offers 4 x isolated serial ports, 6x USB ports and two LAN
connections along with an optional plug and play WiFi module.
Contained in a small and rugged metal enclosure, it may be wall, shelf, desk, or rack
mounted requiring no floor or desktop footprint thereby keeping it out of reach of
unauthorized persons. Has 2G DDR3
Has optional GSM inerface module POA
A measure of product rugged small dimension design and intrinsic reliability is
reflected by its use by NASA, the Australian Military and the well travelled ‘Rolling
Stones’ band.
Note. This product removes the cost and maintenance obligations for UPS
support. (WINDOWS 7 EMBEDDED AVAILABLE POA)
24.2
24.3
N-SMARTCOM-ACC- SmartCom-04 Accessories Kit
This comprises the keyboard and mouse
01
(PC Accessories Kit)
N-SMARTCOMRESET-01
(PC Accessories Kit)
Image
Note This is an important accessory for both the SMARTCOM-M2M OR
SMARTCOM-04 Servers.
Page 78
RSP $
1,444
2,064
42
84
53
60
(Excludes nurse-call
software)
Front & Rear
Views
Accessories Kit
System Reset Switch.
This is an important accessory due to the small dimensions of the computer unit and
generally ‘out-of- sight ’location making it difficult for those rare but predictable need
for floor staff to carry out a computer reset.
W/Sale $
24.4
24.5
24.6
N-SMARTCOM-M2M Compact solid state System Controller including ComwatchMk4 nurse-call
software
(Complete system
The solid state Smartcom-04 has 50,000 hour MTBF and has no moving parts. It
head-end for Radiant- comprises a total nurse-call central equipment M2M (Machine to Machine) controller.
500 and SmcartCare- As such it includes integral software with multiple communication ports to control
500 nurse-call
hard-wired/wireless system inputs plus outputs to paging, Annunciator displays and
systems – Including DECT sub systems.
Comwatch software It logs all incoming and outgoing call traffic, accommodates escalation of
program)
unanswered calls and will accommodate resident, Staff Assist, Duress and
Emergency level traffic.
With its inclusion of all necessary operating and nurse-call software and its choice of
four serial ports, two USB ports and two LAN connections Smartcom-01 becomes
the complete integrated and low cost nurse-call system head-end. It forms the central
equipment requirements for the Wireless Radiant-500 and hard-wired SmartCare500 nurse-call systems. Mouse and keyboard included, video monitor not included.
Note. This product removes the cost and maintenance obligations for UPS
support.
Video Monitor
17 or 19 Inch flat (panel) screen monitor with inbuilt (amplified) speakers. The
(Includes keypad and various nurse-call software provides audio output for remote speaker connection
mouse within part
therefore it is necessary to use the VDU monitor speakers that have audio
number)
amplification, best provided via separately powered monitor having integral speakers.
(Includes Comwatch
Nurse Call Software)
969
1,381
213
304
245
349.5
N-MONITOR-17
N-NPS1-3A-KIT
(Regulated 12v
power supply with
battery and cabinet
including resettable
fuse)
Packaged 12v Regulated 3A Power supply kit with 7AH Sealed Gel battery and
Cabinet
As the SmartCom-04 computer operates from 12v dc (up to 36v dc) it is practical for
the total head-end equipment to operate from a single regulated and battery backed
power supply. This product is ideal and is packaged complete with sealed gel 7AH
battery and includes a resettable fuse.
It is possible to install two batteries in parallel if long term (typically 4 – 8 hours)
battery back-up operation is necessary.
NOTE There is now no need to use an Uninterruptable Power Supply (UPS) as they
are less reliable than the regulated 12v battery backed power supply now necessary
for the Computer operation.
Page 79
24.7
N-CCU-03
(Ademco protocol
telephone input
Controller)
Telephone line call input controller for ADEMCO High Speed - Extended
Protocol)
This special ADEMCO protocol telephone line receiver unit interconnects the
analogue phone line (PABX/PAX/PSTN) to host computer to accommodate
Independent Living Unit (ILU) telephone emergency-call incoming traffic.
Powered from the central equipment 12v dc battery backed supply it includes LED
and Piezo line disconnect alert and two hard-wired trigger inputs all three appearing
as zones 1 to 3 in client code 9001 within the host computer data base if so
programmed.
603
863
315
410
Includes power lead for connection to central equipment 12v power supply. Serial
Communication cable not supplied.
24.8
N-CPU-02-A
(Stand-alone Paging
Encoder)
Paging Encoder Unit
This is a stand-alone paging encoder which, in addition to delivering traffic to a
connected Paging Transmitter, will also facilitate the drive connection to a WAC-07
Annunciator Display controller.
If you need to deliver paging traffic to both a wireless paging transmitter and direct to
hard-wired Annunciator display controller/s, suggest you use a PAGE-SPLTR-01 to
split the coms port data. See details elsewhere within this section.
Note. If using a CCU-03 input controller (above) it should be nted that it does not
include a Paging Encoder section and a CPU-02 device is usually necessary. If using
a WIC-100, WIC-200, WIC-1000M, ASM-02, AE16 or AE32 (described below) as
your nurse-call system master control unit it is then not necessary to use a CPU-02
as those above listed central equipment items also include the CPU-02 paging
encoder functions.
Page 80
24.9
N-AE16-01
(Stand-alone
[computer-less] or
computer connected
hard-wired input
controller)
SMARTCARE-100
This item also forms
the basis of a
complete computer
less system See
SmartCare-100 Data
sheet for more
details)
24.10` N-AE32-01
(Stand-alone hardwired input controller
with 32 hard-wired
inputs)
Hard-wired 16-input controller & paging encoder
As a computer input controller it provides 16 hard-wired inputs from voltage free
normally open contacts or from our range of call-point devices and delivers call,
cancel and assist functions for each connection.
It also will accommodate the system’s paging encoder facility. This can include
paging to hard-wired RS485 Annunciator displays by using the PAGE-SPLTR-01
connection interface.
SmartCare-100 operation
When used as computer-less nurse-call systems by dipswitch selection it can be
joined with up to 9 other identical controllers (and/or wireless controllers) plus a 12v
power supply and paging transmitter to form a complete computerless system. See
System-100 section of price list and data sheet.
530
705
639
830
In this stand-alone (computerless) mode the paging traffic is created by the installer
(or Smart-Caller Service Department) pre-programmed ‘canned messages’ for each
input.
Hard-wired input controller & paging encoder
Similar to the AE16-01 but is limited to connection to the host computer as a 32 hardwired input controller.
Similar to the AE16 controller, the AE32 controller provides a perfect paging encoder
with connections to both Paging Transmitter and WAC-07 Annunciator display
Controller (via PAGE-SPLTR-01 connection panel), whilst also providing up to 32
hard-wired inputs into the host computer system.
It is a perfect solution to a Village Community Centre input controller whereby it
allows hard-wired connections to all call-points and security devices. Unlike the AE16
above it does not have the ability to be provided with canned text messages and is
therefore suitable only for direct connection to the host computer.
Page 81
24.11
N-ASM-02
(Master polling
Controller for
SmartCare-1000
System)
24.12
Master Polling Controller and Paging Encoder.
This ASM-02 (or its wireless counterpart the WIC-1000M) is the essential multitasking part of any SmartCare-1000 hard-wired, reticulated wireless or combined
hard-wired/wireless system.
In addition to providing 16 hard-wired fully featured inputs and a paging encoder, it
also performs the task of polling via hard-wired RS485 techniques to all connected
slave hard-wired and/or wireless area controllers.
The paging encoder is capable of driving both the Paging Transmitter in addition to
delivering an RS485 driver for hard-wired connection to one or more WAC-06
Annunciator Display Controllers.
It will accommodate up to 99 slave wireless controllers WIC-1000S and/or AE32S
hard-wired controllers each also able to accommodate a 100-channel wireless
receiver/decoder known as the Safe-T-Net receiver WPM-01.
This Master-polling controller also has the ability to continue to page outgoing call
traffic (albeit to a single capcode address) in the event of host computer failure. The
default paging dispatches raw paging data (POCSAG) being the event word
accompanied by the system client code for that call-point or device.
Master Polling wireless Controller with Paging Encoder
Complete with its paging and Annunciator Controller encoding facility the WIC-1000M
(as the ASM-02 hard-wired master polling controller) supervises up to 99 Hard-wired
AE32 or AE16 Area Controllers so the WIC-1000M provides a similar service to
WIC1000S Save Area Controllers.
Radiant-1000
Either the ASM or WIC master polling controllers will in fact communicate with any
System
mixture of hard-wired and/or wireless Area controllers.
This item usually
With the advent of the Extension Receivers (RX-EXT-01) of which multiples can be
forms the basis of
applied to wireless Area controllers resulting in extended wireless coverage it is now
the ‘Radiant-1000’
preferable to deploy the hard-wired ASM-02 as the master controlling device. This is
computer-based
because it also allows up to 16 hard-wired inputs at the central equipment location for
wireless systems
monitoring of essential equipment such as power supplies etc.
Remember to select As with the ASM hard-wired controller the WIC-1000M also accommodates paging
traffic to both a wireless paging transmitter and direct to hard-wired Annunciator
antenna- not
display controller/s. Suggest you use a PAGE-SPLTR-01 to split the coms port data
included in price)
to both the paging transmitter and Annunciator controller as described elsewhere
within this section.
It is preferable to use an ASM-02 Master Polling Unit instead of this WIC-1000M
version.
1,029
1,374
1,034
1,375
N-WIC-1000M
(Wireless system
Master Controller)
Page 82
24.13
24.14
N-WIC-100-02
(Also suit Radiant100 computer-less
Wireless system)
Wireless 100 channel Input Controller (304Mhz) and Paging Encoder
This new model includes both RS485 Annunciator Display Driver and a connector to
accept additional Wireless receivers to provide a Space Diversity facility. See RX304BUS-01 Receiver.
Where both wireless paging and RS485 signal delivery is required use a PAGERadiant-100 System SPLTR-01 (See Section 27) to conveniently accommodate both circuits.
WIC-100 is supplied without antenna but includes a power lead on the assumption
This also forms the
basis of the ‘Radiant’ that it will be used with the battery backed 12v central power supply.
If you need to deliver paging traffic to both a wireless paging transmitter and direct to
range of computerless wireless systems hard-wired Annunciator display controller/s, suggest you use a PAGE-SPLTR-01 to
split the coms port data. See details in Section 27.
(Remember to
select antenna- not
included in price)
N-WIC-200-02
(As above but with
200 channels)
Wireless 200 channel Input Controller (304Mhz)
As above but with a 200-channel wireless capacity. This model includes two WIC100 wireless control modules each sharing the common wireless receiver. It will also
accept connection to additional Wireless receivers to provide a Space Diversity
Radiant-200 System facility. See RX304-BUS-01 Receiver.
This also forms the
basis of the ‘Radiant’
range of computerless wireless
(Remember to
select antenna –
not included in
price)
Page 83
572
761
782
1041
As Above
24.15
N-TX148-M-VHF
(Paging Transmitter
Default frequency
148.3375Mhz)
(Remember to
select antenna and
power splitter unit)
NOTE. Does not
include a POCSAG
Encoder therefore
not suitable for
direct drive from
Server. See Salcom
models with
Encoder.
24.16
MAXON 5 WATT PAGING TRANSMITTER
This transmitter works in conjunction with any Smart-Caller encoder such as that
included within the AE-16, AE32, ASM-01/02, WIC-100, WIC-200 and WIC-1000M
equipment.
It is supplied with a 1M interconnecting lead to facilitate connection between the
transmitter and any of the above equipment items. The lead is also provided with a
power connector for the transmitter.
It is a good idea to use a page-spllter-01 power splitter or you will have to connect the
12v power into the back of the connector that fits into the transmitter. Always use a
Page-SPLTR-01 splitter face plate if wishing to split the paging to be shared by the
transmitter and to deliver RS485 data to Annunciator display controller/s.
504
720
504
720
IMPORTANT NOTE.
See the power splitter and paging splitter units listed below. This is particularly
important because the Maxon Transmitters do not have a separate 12v power input
connection and must therefore rely on using a power splitter to be located between
the transmitter and the ASM (or equivalent Wireless Control unit) thereby allowing
the power to be injected via the splitter device. Also note below the System-100 &
Radiant-100 system harness if connecting a transmitter to a computer-less system.
NOTE. Does not
MAXON 5 WATT PAGING TRANSMITTER
include a POCSAG AS ABOVE
Encoder therefore
not suitable for
direct drive from
Server. See Salcom
models with
Encoder.
UHF FREQUENCY
Page 84
As Above
24.17
N-WAC-07
(Hardwired and offair paging receiver to
drive up to 16
Independent
Annunciator displays).
Annunciator Controller - both hardwired and wireless
The WAC-07 superceeds WAC-07-01, WAC-07-02 and previous 02,05 &06 models
Hardwired capability allows the WAC-07 to communicate with up to 16 BESTLITE
displays each with the same or different CAP CODES. On this basis it is possible to
have multiple paging groups with various duty shift call traffic distribution
requirements all controlled via a single WAC.
Includes a VHF wireless POCSAG receiver and is ideal for those applications where
it is not possible to lay cables such as across roads to separate outlying buildings.
627
897
225
322
Approx 80
User Buy
Direct
Approx User
buy direct
In order to carry out the significant programming options the WAC-07 includes a top
LCD display to assist in setting up the significant range of options.
Power pack options are not included (Connection to battery backed centrtal 12v is
prefered) Antenna supplied with each WAC-07.
24.18
N-STARSWITCH-01
(Essential item for
large Annunciator
display systems)
24.19
N-GSM FWT-USB
USB Version GSM Fixed Wireless Terminal From Nurse-Call computer
This unit with its SIM card (not supplied) will allow both-way GSM communication
(SMS deliveries to off- between the Host computer and various GSM mobile phones.
site mobile phones
etc)
It will for example deliver escalation calls to off-site staff or auto/manually compiled
SMS messages to Maintenance, Security, Management, Doctors or others as
required.
This item is also ideal for allowing GPS tracker location traffic to be applied to a
Google map facility via a Winwatch Nurse-call software module.
Note. Make sure that your Winwatch software has the GSM SMS driver module for
this unit to communicate into the GSM network. (See WIN-GSM-01 in the Central
Equipment software section 28.
Page 85
24.20
24.21
N-DURALINK BS-01 Duralink Base Unit for connection to host computer
(Base unit capable of This version of Base Unit simply offers a serial port connected ADEMCO protocol for
controlling up to 99
connection to the host computer.
Transponders)
Refer to items 15.7, 15.8 & 15.9 for full descriptions and refer to ‘Duralink’ data sheet
for system configuration details.
(Remember to
select 433Mhz
antenna)
N-DURALINK.BS-02
(As above but
including the
reconstitution of
original 304Mhz
transmission)
Duralink Base Unit for connection to host computer or wireless retransmission
As an alternative to the above facility this model also delivers a reconstructed original
wireless transmission on the original 304Mhz frequency. The latter allows the signal
to be connected into the WIC-100/200 wireless controller for canned message
dispatch and/or be delivered into a nearby HP3 phone, HD4 Smart-Dialler or perhaps
to a Site-Wide Dialler, the latter being capable of processing up to 256 incoming
wireless and subsequent monitoring centre client codes.
(Remember to
select 433Mhz
antenna)
Page 86
341
453
451
600
As Above
PART ‘M’ – PROTOCOL CONVERTORS & HARDWARE INTERFACE ITEMS
NEW ITEM
25.
CENTRAL EQUIPMENT INPUT PROTOCOL-CONVERTORS & SUB SYSTEM HARDWARE INTERFACES
NOTE. As with all Protocol Convertors it is necessary that the
incoming traffic contains key (global) words (such as ‘Call’ and
‘Cancel’) along with a unique number in order to establish a new
database entry within the host computer or other processing device.
Protocol convertors have the benefit of providing a seamless
connection between the original device or system and the new nursecall host computer.
25. HARD-WIRED PROTCOL CONVERTORS
Item
25.1
Description
High-level Fire-Panel system Protocol Convertor (interface).
This interface connects between the host computer and any single third party
(High level system
system, which can include a fire-panel, security system, access control system or an
interface, typically for existing nurse-call system.
Fire Panel
It requires a simple two-wire connection as it only accommodates ‘send’ traffic from
connection)
the parent device. As fire panels and other devices are often outside of safe RS232
protocol range (i.e. 10-20M) the BMS-01 interface includes both RS232 and RS485
connections.
Installing system specific microprocessor firmware has accommodated most
systems; however, it is important to ensure firmware availability before committing to
an interface.
Model
N-BMS-XX-01
Ensure that you allow some hours to enter the fire panel database into Comwatch or
Winwatch software, as it is usually 2 to 3 times the number of normal Resident room
client database entries.
RANGE OF INTERFACE FIRMWARE AVAILABLE (contact us for other models
Fire Panels)
Vigilent, Ziton, Siemens, Ampac, Concept, Notifier, Pertonice, Tyco (Wormalds).
Note. Plug-pack Power lead and serial communication cables are not provided as
the interface should be powered from the nurse-call 12v regulated and battery
backed power source.
Page 87
Image
W/Sale $
RSP $
950
1260
26. WIRELESS PROTCOL CONVERTORS
Item
26.1
26.2
Description
27Mhz call traffic to ADEMCO Protocol Convertor
This central equipment optional item has been designed to capture 27Mhz wireless
(Capture 27Mhz (low traffic using the standard Elsema protocols (as used within OPSM, Village Watch,
band VHF) call traffic Village Alert, Visiplex , Mical and other similar systems) and to convert those calls
for nurse-call
into standard ADEMCO protocol for processing by Smart-Caller compatible nursecomputer processing) call host computer systems.
Note. Smart-Caller will require the use of a sample 27Mhz transmitter to verify
system compatibility. In this respect we no longer process Vitalcall call traffic.
Note. See Section 35 for 27Mhz products to support and/or convert legacy 27Mhz
systems.
Model
N-WIC-05-01
N-WIC-05-02
(As above but with
304Mhz
retransmission
capability)
(Remember to
select two
antennas)
27Mhz to Ademco and 304Mhz Protocol Convertor
This model is as the -01 version but includes an internal 304Mhz low powered
transmitter which effectively allows incoming calls (in addition to being converted to
Ademco format) but also to allow those incoming 27Mhz calls to be retransmitted
with unique identifying code for processing via various 304Mhz receivers such as
those within HP3 phones and HP4 Diallers for off-site delivery to central monitoring
companies.
For large sites with more than 48 incoming 27Mhz transmitters the Site-Wide dialer
should be used, each of which is capable of handling up to 256 unique incoming
27Mhz transmitters.
See Item 1.8 HP3-SITEWIDE-01 for more information.
Page 88
Image
W/Sale $
RSP $
494
578
525
698
PART ‘N’ – CENTRAL EQUIPMENT MISCELLANEOUS EQUIPMENT
27. CENTRAL EQUIPMENT MISCELLANEOUS & SIGNALLING PROTECTION ITEMS
(A check list of useful miscellaneous items not included elsewhere)
Item
27.1
Model
N-CAB-01
(Equipment Cabinet
With key lock and
handles)
Description
Equipment cabinet.
Ventilated, metal cabinet with lockable door. There are various brands and sizes to
chose from.
These should be used throughout the system both at the central equipment location
and at each area controller location to ensure a neat and tamper-free installation.
Image
W/Sale $
RSP $
102
136.5
47
67
37
52.5
POA
POA
Make sure that you use a standard key lock (for all sites). Standard unit dimensions
H440mm x W310mm x D110mm. Do not install wireless devices within these
cabinets unless a BNC or SO259 coaxial socket is provided (Model CAB-02).
27.2
27.3
27.4
N-PAGE-SPLTR4WAY
Paging/Annunciator communications path splitter.
For any of the hard-wired central equipment items that requires the Paging Encoder
facility to deliver call traffic to both the Paging transmitter and the Annunciator
Controller(WAC-07) it is necessary to split the single D9 connection to two separate
(For use with HardWired central located devices. The PAGE-SPLTR-01 provides a simple patch panel to achieve this.
This item is no longer required for wireless control units as those products now
controllers where
include a connection for both the paging transmitter and Annunciator controller.
paging and
Annunciators are to
be deployed.)
N-PAGE-SPLTRPaging Transmitter to Paging Encoder Power supply Splitter
Comprising a standard electrical 70 x 115mm faceplate with two D9 connectors. This
2WAY
item is used only with computer-less System-100 hard-wired and Radiant-100
wireless systems where the power supply and paging transmitter are required to form
(For use with mini
(computerless) hard- part of the equipment interconnection harness. See next item for harness details.
wired systems)
The PWR-SPLTR-01 simply allows you to inject the 12v supply into the harness on
D9 connector pins 1 and 9 via a rear mounted terminal block.
N-CANNING-01
(Creating canned
messages for AE16
controller or WIC100/200)
Programming Canned messages (Via Smart-Caller Service Dept)
By supplying ‘Canned Message’ requirements for each of the AE16 hard-wired
controllers or up to 100 for each WIC-100 Wireless controller Smart-Caller will deliver
the hard-wear fully programmed and tested for a service department fee. This can
save you significant installation time.
Page 89
PROGRAMMING
27.5
N-SYS-HARNESS-5
(Interconnecting
harness)
(For use with
SmartCare-100
Systems)
System-100 and Radiant-100 computer-less system Interconnecting Harness
Designed for hard-wired computer less systems, this harness interconnects all active
components of the system via a 9-way flexi cable having [X] number of D9
connectors fitted in close proximity spaced sufficient to allow the required number of
AE16 controllers, plus the 12v power supply (via the above power splitter (not
included) and (if required) the paging transmitter to share the harness.
You can create your own harness or we can offer two standard versions being a 5way and 10-way being 5 or 10 fitted sockets respectively. It can include provision for
both a paging transmitter and/or connection to hard-wired Annunciator controllers.
73.5
95.55
116
165
EST
89.25
EST
118.65
It is also recommended to include a PWR-SPLTR-01 (power splitter) to inject the 12v
supply into the harness.
If making your own harness remember that we are dealing with low (TTL) level data
so keep the harness short and no longer than 10M and ensure that the paging
transmitter is at the end for maximum separation.
27.6
27.7
N-SYS-HARNESS-10 As above but for larger (typically up to 10 unit connection)
N-NOVARIS RS485
(Novaris SL line
protectors)
Plug-In RS485 Signal Line Protection
These devices sit across EACH end of the RS485 bus to prevent induced
voltage from blowing the RS485 send/receive microprocessors. Each device
has a true Earth connection and surges are diverted to earth via the
connection.
Note. When you order the device, ensure that you also get a piece of Din rail to
mount it on. The Din rail is then earthed.
Page 90
PART ‘O’ – NURSE-CALL SOFTWARE PROGRAMS & OPTIONAL MODULES
28. CENTRAL EQUIPMENT SOFTWARE PROGRAMS & OPTIONAL SOFTWARE MODULES
Item
28.1
Model
N-WINWATCH-01
(Basic ‘current
version’ Nurse Call
Software package)
Description
Windows Based Nurse-call Software
Windows based nurse-call software management program with handbook and first
year license fee. To suit single site operation.
Image
Includes install disk with hard and soft copy of both installation and operator’s
manuals. See also annual License fees below. Remote maintenance also available
on do and charge or contract bases.
W/Sale $
RSP $
2,100
2,625
210
266
265
350
Note. New deliveries of Winwatch will include various optional accessory
modules at the discretion of Smart Caller.
SPECIAL NOTE. Software product warranty applies only if installed within a
Smart-Caller supplied SmartCom-04 solid state Server. See item 24.1
28.2
28.3
N-COMW-WIN-01
(DOS to Windows
Database upgrade)
N-WINWATCH-U/G
(Version upgrades)
Export DOS database to Winwatch Entry Level –
NOTE DOES NOT INCLUDE ABOVE WINWATCH PROGRAM
To export from DOS Comwatch version software to Windows operating Winwatch
version.
Note. This cost is to export the original DOS databases into a new Winwatch
program and does not include the cost of the Winwatch program (See below).
Note 1 zipped copy of total existing Ver 3_34 program required in order to carry out
upgrade.
Note 2. If existing DOS version is lower than version 3_34 an additional service
department charge will be applied based on time to carry out the DOS upgrade to
exportable level.
Winwatch Upgrade Programs
Each new series of system upgrades will be published listing new facilities and these
upgrades will be issued with appropriately upgraded handbook information.
Upgrades will carry a new software version number and costs will be identified for
each upgrade. Typical upgrade cost is listed herein but may change from version to
version. New Winwatch installations will include the latest version.
Clients having valid maintenance agreements (See Item 28.18 below) will receive
basic system upgrades to their existing operating modules free of charge. Charges
may however apply where significant new facilities are being introduced within the
Winwatch software environment.
Page 91
UPGRADE
28.4
Software module to Interface BlueLine-IP system to Standard Winwatch program
Whereas existing and legacy nurse-call equipment use the traditional Ademco
protocol via serial communication ports, this software module will simultaneously
process Ademco serial inputs in both Ademco and will accept the SmartCare-IP
nurse-call system input via a standard Ethernet LAN connection.
It introduces remote monitoring through Web Server and Email alarm and remote
maintenance. It also supports SQL database ancillary programs.
263
341
N-WIN-KIRK-DECT- Kirk/Polycom SMS Software module Interface
This is an economical software alternative to using the Multitone P318 hardware
ANA
interface or other similar commercially available interface products. It suits
(Software module for interconnection to the Polycom Control unit where those DECT handsets and
connected via Analogue ports.
SMS messaging to
Kirk DECT Systems)
Its function is to deliver SMS messages to DECT phones thereby functioning in a
similar way as an alphanumeric text messages to pagers.
315
420
315
420
315
420
315
420
N-WIN-IP-01
(System BlueLine-IP
Interface module)
28.5
28.6
N-WIN-KIRK-DECT- WIN-POCSAG ENC
(A software module to replace the ASM/AE/WIC hardware encoders)
IP
(Software module for
SMS messaging to
Kirk DECT Systems)
28.7
N-WIN-POCSAG
ENC
(A software module
to replace the
ASM/AE/WIC
hardware encoders)
Software generated POCSAG Encoding for direct connection to Paging Tx &
WAC-07
This software module will replace the need to have the currently required ASM/AE or
WIC central equipment the currently includes a PCB to provide POCSAG protocol to
the paging transmitter and Annunciator display unit (WAC-07)
It is primarily necessary for the BlueLine-IP system where no such central equipment
is necessary.
28.11
N-WIN-GSM-FWT-01 Winwatch Software Upgrade to incorporate GSM-FWT hard-ware.
This optional Winwatch software module will allow a USB connected GSM Fixed
(Software interface to Wireless Terminal (FWT) to be utilized for both-way GSM communication.
provide bothway
communication to
In addition to allowing off-site SMS messages to mobile phones it also has
GSM network)
application when using GPS/GSM personal and asset tracking allowing position
coordinates from tracked devices to be delivered into the Winwatch system via the
GSM interconnection.
Also see WIN-GPS TRACKING-01 below.
Page 92
28.12
28.13
N-WIN-TRACKER-01 Winwatch GPS tracking facility
Deploying Google map display facilities this software will provide the link connection
between the WIN-GSM-FTW communication facility connected to a USB port and the
(GPS Global
Google map.
Personal & asset
tracking software)
DEVELOPMENT
M-GPS TRACKER02
(A stand-alone GPS
map tracking
software program)
28.15
28.18
N-WIN-AMCOM
(Interface between
Winwatch and :Vocera,
Cisco Wifi,
Spectralink,
Email,
NEC/Philips DECT
Motorola wireless,
Other )
Copy of 3rd party stand alone GPS/GPRS tracking program with Google map
exploitation
For those that wish to keep the person and asset tracking facility outside of the
Winwatch operation this software program may suit that requirement.
TBA
TBA
TBA
TBA
POA
POA
500
500
N-AMCOM-CommtechWireless Message Centre
This item is capable of converting Winwatch host computer data output to
interconnect with a wide range of mobile display units as listed.
The program called AMCOM Messenger resides within the SmartCom-04 Server and
delivers appropriate protocols to the selected for of display device/s.
For extra cost it is capable of communicating with multiple sub systems in addition to
those already fully supported by the other Winwatch interface modules such as
paging, GSM and others.
HELP DESK
ANNUAL REMOTE ACCESS AGGREEMENT (12 MONTH)
Charged direct to end user client and is dependent on that party making internet
SUPPORT
(License/Maintenance access facilities available to accommodate remote desktop access.
of Winwatch)
Fee includes updates to existing operating modules but excludes new optional
NEW ITEM
modules that may be offered from time to time but will include the maintenance
thereof.
Page 93
PART ‘P’– DECENTRALIZED (AREA) SYSTEM CONTROL EQUIPMENT
29. RS485 HARD-WIRED AREA CONTROL EQUIPMENT
Item
29.1
Model
N-AE16S-12V-24V
Description
Hard-wired Controller
These hard-wired controllers are designed to operate from external 12v or 24v
closing contacts, call-points, lamps or mimic panel LED/incandescent lights.
Image
A typical application is to connect them across the mimic display of existing nursecall systems. See also the AE16S and AE32S versions that are polled by the host
computer.
Communication cables not included.
29.2
29.3
29.4
N-AE16S
(16 Input Slave Area
Controller)
Hard-wired 16-input slave Area Controller
This item will allow the connection of up to 16 hard-wired connections and is polled
by the Master Controller.
N-AE32S-02
(32 Input Slave Area
Controller)
32 hard-wired Input Area Controller with Safe-T-Net receiver socket.
As above but with provision for connection of 32 hard-wired inputs and the ability to
connect a Safe-T-Net wireless receiver providing a further 100 wireless channels.
Note. Don’t forget to use some RS485 protection devices – see miscellaneous items
below.
Special Note. Unless using the new alternative ‘IP Blue-Line’ Area Controllers this is
the standard Area Controller used within a standard RS485 polled SmartCare-1000
Hard-wired Nurse-Call system. It offers ‘per connection’ cost benefits over the AE16
alternative listed above.
N-WPM-02
(Safe-T-Net 100channel Wireless
Receiver option)
(Remember to
select antenna)
W/Sale $
RSP $
550
730
550
730
630
820
150
215
As Above
Safe-T-Net Wireless Receiver with extension receiver Connector
This 304Mhz receiver will allow any 16 or 32 way hard-wired slave area controller to
receive and process up to 100 channels of wireless devices. These may include
pendants, utility transmitters, wireless call-points, bed exit and bed wet sensors,
wander alert and doorbell alerts and similar compatible wireless devices. It will also
accommodate the RX304-BUS-01 extension Receivers.
It also acts as a solution for staff duress and will also accommodate most of the
NESS manufactured standard 24-bit protocol wireless devices. Check compatibility if
using new NESS devices.
Note. It will also accommodate the RX-EXT-01 Extension receiver which significantly
Page 94
29.5
N-LOCKOUT-PCB01
(Used to control interroom wireless trigger
activity)
Call-point wireless trigger lockout panel
When using hard-wired call-points that have wireless trigger it is possible for
any pendant to trigger a corridor call-point. This lockout unit fits within the
equipment cabinet at each Area slave controller location.
It provides a cable termination diode protected single core connection back
to each bedside call-point to provide a lockout pulse to ensure that a
resident’s pendant triggered within his/her room will not trigger nearby
corridor or communal area call-points.
Page 95
42
55
30.
Item
30.1
WIRELESS AREA CONTROL EQUIPMENT
Model
N-WIC-1000S
(UHF Wireless area
controller)
Description
Wireless Area Controller (100 Channel) (Forms part of SmartCare-1000 polled
system)
Operating as a slave controller being polled by a central equipment ASM-0x or WIC1000M master controller the WIC-1000S will monitor, accept and process up to 100
individual wireless codes with call, cancel, assist and low battery traffic.
(Remember to
select antenna)
It may be included within a hard-wired system and visa versa. Up to 99 controllers of
either hard-wired and/or wireless may be included within a system of up to 1.4kM
cable length.
Image
W/Sale $
RSP $
589
783
273
375
As a typical alternative the safe-T-Net receiver may be used in conjunction with a
hard-wired AS16S or AE32S hard-wired controller.
30.2
N-WRX-304-01
(UHF Range
Extender- Repeater)
(Remember to
select antenna)
UHF Range Extender (Repeater)
Designed to allow the range of 304Mhz call-points, pendants and other transmitting
devices to be significantly extended to a further 150 -300M depending on building
construction constraints.
The design is such as to allow multiple WRX units to operate in the same location
due to the ability to independently set the repeat transmission and ignore same call
intervals. This allows considerable flexibility in designing wireless systems whereby
calls will be carried from repeater to repeater without the usual ‘Ping-Pong’ effects or
carrier frequency signal overlap causing corrupt signaling.
The WRX-304-01 includes a plug-pack and integral battery back-up and via its BNC
connector will allow either low efficiency ‘Rubber Ducky’ (flexi) antenna connection or
connection of efficient external or roof cavity mounted antenna via coaxial cable
connection (See antennas in section34).
Page 96
30.3
N-RX-EXT-01
(Extending the range
of wireless
processing
equipment)
Plug-in Extension wireless Receiver
Due to achievable range of 304Mhz transmissions being fraught with difficulties
within building layouts plus the problem of using multiple range extenders, the use of
a small network of multiple receiver units associated with the call processing
equipment in a particular area can be a low cost and effective solution in such
environments.
1-5=150
6+=POA
215
POA
150
POA
215
POA
150
215
Image also shows
multi-receiver ‘splitter The use of one or more of these receiver units can significantly expand the reception
range of products such as the WIC100, WIC-1000M, WIC1000S, WPM-01 Safetybox’. Not included
Net Receiver, range extenders and Diallers to name a few. The Receiver is fitted
with an RJ connector. Make sure that the correct parent item (with corresponding
remote Receiver RJ socket) is selected. Use an RJ splitter unit (as illustrated) if
additional Receivers are required.
30.4
30.5
N-RX-DIVERSITY-01 Diversity receiver/decoder
(UHF Bus network
This unit when fitted with its optional decoder chip fitted will receive and decode all
304Mhz wireless traffic allowing the decoded data to be delivered to parent
receiver)
equipment that will process that traffic to the head-end system.
NEW ITEM
(Remember to
This model also forms the latest version ‘Safe-T-Net’ receiver for connection to a
select antenna)
hard-wired Area Controller. Two or more RX-DIVERSITY receivers may be
interconnected to the Area controller thereby significantly extending the possible
range of incoming wireless traffic into a hard-wired system.
N-RX-DIVERSITY-02 Diversity Receiver
As above but with the decoder function disabled. In this mode it operates much the
same as the RX-EXT-01 Extension receiver.
Page 97
As Above
30.6
N-DURALINK-TP-01 Duralink 304Mhz to 433Mhz UHF Transponder
(Duralink sending
Acting like an extended range WIFI system, this Transponder unit accepts normal
end Transponder)
Smart-Caller, Ness and Smartlink 24-bit 304Mhz wireless traffic and retransmits it at
the higher allowable transmitting power of 25mW using digital transmission on
(Long Range WIFI)
433Mhz. This can extend the range of the original transmission typically up to 600M
in free space and typically 150M in a building environment.
(Remember to
select [2] antenna) For maximum reliability each Duralink Transponder is constantly polled by its head
end polling controller (Model Duralink-BS- XX) and all received call traffic is
confirmed back to the sending end Transponder before onward processing.
Each Transponder is capable of sending regular test calls and will report a low
battery or power fail condition to its master controller head-end. Up to 99
transponders may be deployed.
542
720
47
67
These transponders can only communicate with their respective head-end master
controller (DURALINK-BS-01 in Section 26) and therefore provides a totally
independent communications system, which also makes it ideal for Staff Duress
applications.
30.7
N-RJ-SPLITTERBOX
(A six socket
‘connection bus’ for
multiple use of RXEXT-01 units
Repeaters and Transponders are supplied with NiMH battery back-up and a
plug-pack.
RJ connection Box for RX-EXT-01 multiple receivers
This connector box allows the connection of up to 5 RX-EXT-01 receivers to all
wireless receiver equipment and is listed here as a ‘Check-List’ item.
Note. This is a ‘Check List Item otherwise easily forgotten.
Page 98
31. ‘BLUE-LINE IP’ SYSTEM AREA CONTROL (NODE) EQUIPMENT
Item
31.1
31.1
Cont
Description
Introduction to Blue-Line IP Multipoint Area Controllers (TPC/IP Nodes)
As with the market dominance of the Smart-Caller ‘Blue-Phone’ Emergency-Call
Introduction
system so the Smart-Caller ‘Blue-Line’ IP nurse-call system offers the same potential
dominance within the Ageing-in-Place’ hard-wired and wireless nurse-call systems
(Introduction to
The ‘Blue-Line’ system is a PC based data acquisition and control network whereby
Multipoint IP System) the central equipment (PC) is in constant contact with each of its family of ‘BlueLine’
Area Controllers (or Nodes) via an Ethernet LAN connection.
Each installed Node includes the required number of 16 input ‘plug-and-play’ I/O
modules which means that any single Node location can range from 16 input to 128
inputs. The illustrations show both 4-module and 8 module Nodes and a typical 32input node would deploy a 4 –module housing with two matching blank panels for the
unused module locations.
Each Node communicates with the host computer using standard commercial LAN
Switches Router/hubs using TCP/IP (Transmission Control Protocol/Internet
Protocol). TCP/IP is a descriptive framework describing the Internet Protocol Suite of
computer network protocols.
Model
‘BLUE-LINE’ IP
31.1 Cont'd.
Each Area Controller (Node) also includes both RS232 and RS485 gateways to
accommodate and to convert the protocol of possible analogue and perhaps legacy
equipment which has ongoing operational functions.
Similarly the network will accommodate separate and low cost ‘on-line’ analogue to
digital gateways as illustrated below.
The standard module accommodates up to 16 call-points via a single wire connection
to the quick release multipart connector. Each of the wire terminals is protected by
isolating opto-coupling and includes an adjacent LED indicator offering an ideal
installation tool and diagnostic facility.
Other modules in the range include those with 32 input capability having lesser
protective facilities, others with low power transistor switching plus others with high
power (3Amp) contact switching with normally open/normally closed contact options
and others offering RJ connection facilities.
Page 99
Image
W/Sale $
RSP $
See below
See below
See below
See below
31.1
Cont
31.2
31.1 Cont'd.
N-BL-CCECHEADEND-01
The complete Node assembly would normally include the BlueLine-IP controller
along with the required number of plug-in modules plus DIN rail mounted power
supply, plus the NODE RJ45 Patch/Distribution panel which allows direct connection
from each room or communal area call-point to its parent I/O Module.
In accordance with Australian Standard AS3811 the system installation concept uses
an independent ‘sub-net’ cabling infrastructure terminating at the head-end
SmartCom4 Industrial quality Nurse-call Server using standard commercial routing
switches as necessary to minimize cable lengths.
A major benefit of deploying ‘Blue-Line IP’ Area Controllers is their backward
compatibility with existing Smart-Caller products and systems. For example
connecting the standard range of extremely reliable call-points with their multiple
circuit capability, Call, Cancel and Staff Assist functions plus Wireless Trigger and
Heartbeat monitoring functions are all fully supported by the these ‘Blue-Line’ Area
controllers (Nodes).
See Smart-Caller ‘Blue-Line’ IP System Data sheets at www.smartcaller.com.au
See below
See below
CENTRAL CONTROL EQUIPMENT CABINET
Each Blue Line system comprises of a central control equipment cabinet and some
node cabinets. Simply connect each cabinet via the LAN for a true plug and play
senario. Each central control cabinet will contain certain essential components and
optional components as required for each project. To cost your requirement add the
cost of the optional componets to the CCEC-Blueline cost.
ESSENTIAL ITEMS INCLUDED: SMARTCOM-04. WINWATCH-01, WIN-IP-01 (IP
MODULE UPGRADE), 10AMP DRAN POWER SUPPLY, 20 AMP BATTERY,
BATTERY MANAGEMENT SYSTEM, LAN SWITCH, RESET SWITCH,8 WAY
POWER BOAD, ASSEMBLY.
OPTIONAL ITEMS: Add and cost as required. Please check prices in body of price
list as the price of these items might change and might not be updated in this section
. Current as at 01/03/14
WAC-07
$597 RRP $854
STARBOX-01
$225 RRP $322
TX148-M-VHF MAXON PAGING TX 5W $465 RRP $665
ANT-VHF-297 PAGING ANTENNA
$70 RRP $100 (other options
available)
WIC-100-02 FOR PAGING ENCODER $545 RRP $725
PAGE-SPLTR-01
$45 RRP $64
DECT INTERFACE INCL DURESS
$2574 RRP $3680
NOTE IF INTERFACE IS PURCHASED WIN-IP-01 IS NOT REQUIRED (DEDUCT
$250
RRP $325)
BMS-01 FIRE PANEL INTERFACE
$950 RRP $1260
(Please advise fire panel model when placing order)
ANT-304-FLEXI-01 WIC ANTENNA
$26
RRP $37 (other options
available)
5,068
6,764
Page 100
31.3
31.4
31.5
N-BLUELINE-32NODE
(Exactly the same as
the 64 Node below
but less 2 modules.
Easily expanded to
64 inputs by adding 2
modules)
Complete pre-assembled 32 input TPC/IP Node (Ready for installation)
Smallest Node yet easily expanded at a later date to accomodate 64 inputs.
(Exactly the same as the 64 Node below but less 2 modules. Easily expanded to 64
inputs by adding 2 modules)
N-BLUELINE-64
NODE
(Complete Node
capable and
equipped for 64
inputs)
Ready for wall-mounting this complete Node with 64 input capacity (4-module slots)
fully fitted for 64 inputs plus two 12v regulated power supplies, 20AH battery, Power
distribution unit and 64 way RJ45 patch-distribution panel pre assembled and fully
tested.
This Node is fully loaded for 64 inputs. Should you require less inputs deduct the
price of unwanted 16-way modules.
Special note: Please leave one input spare for every 32 inputs for power fail
reporting purposes.
N-BLUELINE-128NODE
Ready for wall-mounting this complete Node with 128 input capacity (8-module slots)
fully fitted for 128 inputs plus 12v regulated power supply with 30A UPS and battery,
a DIN rail mounted Power distribution unit and two 64 way RJ45 Patch/Distribution
panels all pre assembled and tested.
This Node is fully loaded for 128 inputs. Should you require less inputs deduct the
price of unwanted 16-way modules.
reporting purposes.
Note. Image shows a system fully installed complete with 64 room/communal area
cable connections each RJ45 connection providing both-way control and power to
two call-points thereby accommodating a total of 128 connections less those
allocated to Node diagnostics.
(Complete Node
capable and
equipped for 128
inputs)
31.6
N-BLUELINE-16IPMODULE
NOTE-SLOT
NUMBER MUST BE
SPECIFIED WHEN
ORDERING. SEE
TECHNICAL MANUAL
OR CONTACT
S/CALLER
2,420
3,460
2,948
4,216
4,879
6,977
264
378
reporting purposes.
BlueLine 16 input Module fitted with two 8-way RJ45 fly-leads
This module forms the basis of each Node whereby it is configured to accept 16 callpoint or other inputs delivered via two RJ45 leads which in turn connects to the
Distribution/Patch Panel located within each Node.
Each input uses opto-coupled connections for overvoltage protection and is capable
of monitoring Alarm, Cancel, Assist and call-point heartbeat communication.
Page 101
As below but with
one distribution panel
31.7
31.8
31.9
N-DECTDECT INTERFACE INCLUDES DURESS MODULE
Note: if you are using a Dect Interface you do not need to purchase WIN-IP-01
INTERFACE-01
SOFTWARE MODULE
(Inc Duress
management System)
N-64001-BAT
Panasonic Battery
N-BLUELINEBLANK- PANEL
(Plug-in Blank
Panels)
REPLACEMENT 12V 20Amp battery for Blue Line IP system
Each Power Supply has a 20AH battery back-up contained on a shelf within the Node
Cabinet. Changeover to battery operation will generate a Diagnostic alarm into the
system for distribution and logging.
2831
4048
90
128
27
36
529
756
655
937
PLUG-IN BLANK PANELS (to cover unused module slots)
Each 4-slot assembly is supplied with two blank panels and each 8-slot assembly
includes 4 blank panels within the price.
31.10. N-BLUELINE-CU4SLOT
(Controller and back
plane PCB with
sockets to accept
four plug-in modules)
REPLACEMENT Area Controller Node assembly with 4-slot 64 input system
capacity NO MODULES INCLUDED
Standard DIN rail mounting 4-slot Node control Assembly showing two blank panels
and without any I/O Modules. With all four modules fitted will accommodate 64
external inputs plus power supply module diagnostic internal inputs.
31.11. N-BLUELINE-CU8SLOT
REPLACEMENT Area Controller Node assembly with 8-slot system capacity
NO MODULES INCLUDED
Standard DIN rail mounting 8-slot Assembly without modules but fully loaded with
blank panels.
This version will accommodate up to 8 x 16 inputs however, 4 inputs will be reserved
for power-supply failure diagnostics.
(Controller and back
plane PCB with
sockets to accept
eight plug-in modules)
IMAGE NOT
AVAILABLE
Although shown with all 8 blank panels fitted, when supplied this unit is supplied with
4 bank panels.
Page 102
31.12
N-BLUELINEPATCH/DIST-01
DPP
(19” rack mounting
RJ45 patch and
power distribution
panel)
REPLACEMENT Special RJ45 patch and Distribution rack mounting panel to
accommodate 64 inputs
Using 2-level 8-stack RJ45 socket assemblies throughout the panel s this special
panel at its left hand section accommodates the two fly-leads from each fitted module
therefore accommodating 4x16= 64 internal connections to the assembly back-pane.
The remainder of the panel includes the same RJ45 block configuration having a
total of 32 sockets each accommodating up to two circuits from the rooms and
communal areas thereby allowing up to 64 inputs into the Node.
In addition to accommodating call, cancel, assist and heartbeat communication from
each connected call-point, each socket also provides the regulated and current
limited power source to each connected call-point.
Two of these special patch/Distribution panels would be installed if using the 8-slot
(128 input) Node described in item 31.4.
Special note: Please leave one RJ input spare for every 32 RJ connections for
power fail reporting purposes.
801
1,146
SPARE CABINET The 6RU BlueLine-IP Cabinet
This version will be the predominant cabinet with expansion capability and in view of
the volume of cables entering and leaving the cabinet.
Its Dimensions are H 368mm – W 600mm – D 550mm (See image)
200
286
31.13B N-6RU-SWING-OUT SWING OUT MOUNT FOR 6RU CABINET
550 deep cabinet rear mounting 'swing-out section' complete with both left and right
hand hinges. Allowing easy access to rear of cabinet for install and serviceing
purposes.
236
314
230
325
330
450
120
160
31.13
31.14
N-BLUELINE-CAB6RU
N-BLUELINE-CAB9RU
SPARE CABINET The 9RU BlueLIne-IP Cabinet
This version is intended for the 8-slot 128 input Node where it has to accommodate
the full rack width 8-slot BlueLIne-IP controller assembly plus a number of power
supplies with their back-up batteries, Patch panels etc.
Its Dimensions are H 500mm – W 600mm – D 550mm. (See image)
31.14B N-9RU-SWING-OUT SWING OUT MOUNT FOR 9RU CABINET
550 deep cabinet rear mounting 'swing-out section' complete with both left and right
hand hinges. Allowing easy access to rear of cabinet for install and serviceing
purposes
31.15
N-DRU-30
(30amp UPS)
30A 12V REGULATED POWER MANAGEMENT UNIT
A comprehensive DIN Mounting 12v UPS and power reglation system with battery
monitoring capability. Se next item for compatible power supply.
Page 103
31.16
31.17
N-DRAN-120
(Regulated 12v 10A
power supply)
10A 12V REGULATED POWER SUPPLY
High quality DIN mounting 12V 10A regulated power supply. See above item and N64001 special battery.
550 deep cabinet rear mounting 'swing-out section' complete wit both left and right
N-BLUE-LINE-IP hand hinges. Allowing easy access to rear of cabinet for install and serviceing
MINI
(12-way multipoint IP purposes.
area controller - Node
Page 104
107
143
POA
POA
32. ANNUNCIATOR DISPLAY AREA CONTROL EQUIPMENT
Item
32.1
32.2
Model
N-STARSWITCH-01
N-BESTLITE-PLUGPACK-01
(Stand-alone power
source for BESTLITE
Display)
Description
12v DC 1.5A Plug Pack to suit BESTLITE Annunciator displays
A clean power source (i.e. one having no AC content to ground) is essential to avoid
corrupt displays, this is particularly important for large Annunciator installations. It
should also be recognized that a single display can draw up to 800mW when
displaying a full screen.
Using this approved plug-pack for each display overcomes the corrupt display
problems but does not provide a battery backed facility.
Using a good quality 12v battery backed power supply offers the alternative solution
however do not allow cable runs to exceed 30M if using CAT5 cabling. Contact
Smart-Caller Service department for detailed information and advice and ask for a
copy of the RS458 network design bulletin.
Page 105
Image
W/Sale $
RSP $
236
338
49
69
33. MISCELLANEOUS ITEMS FOR AREA CONTROL
Item
33.1
Model
N-NPS1-3A-KIT
(Regulated 12v
power supply with
battery and cabinet
including resettable
fuse)
33.2
N-NPS1–3A
(Regulated power
supply)
Description
Packaged 12v Regulated 3A Power supply kit with 7AH Sealed Gel battery and
Cabinet
As the SmartCom-04 computer operates from 12v dc (up to 36v dc) it is practical for
the total head-end equipment to operate from a single regulated and battery backed
power supply. This product is ideal and is packaged complete with sealed gel 7AH
battery and includes a resettable fuse.
It is possible to install two batteries in parallel if long term (typically 4 – 8 hours)
battery back-up operation is necessary.
NOTE There is now no need to use an Uninterruptable Power Supply (UPS) as they
are less reliable than the regulated 12v battery backed power supply now necessary
for the Computer operation.
Image
W/Sale $
RSP $
245
349.5
199
262.5
32
45
13.8v (Regulated 12v) Power Supply
The NPS1 is a versatile regulated 3A DC power supply and SLA battery charger.
Featuring five 13.8V outputs each separately fused with auto resetting electronic
fuses, SLA battery charger, removable terminals, LED status indication and a Mains
Fail relay output for interfacing to other equipment.
Supplied with 240V mains adapter, the NPS1 is ideal for nurse-call and access
control applications, additional power for large installations and anywhere that
regulated DC power with battery backup is required.
There is also a fully packaged and enclosed version where you may wish to power
and battery back some Annunciator displays.
33.3
N-BAT-03
Sealed Gel 7AH back-up battery
(Sealed battery back- To be located within the equipment cabinet/s as described below.
up)
Page 106
33.4
N-CAB-01
(Equipment Cabinet)
Equipment cabinet.
To hide cabling and to ensure anti-tamper or the access by other trades it is
important to place decentralized equipment within a ventilated, metal cabinet with
lockable door. There are various brands and sizes to choose from.
These should be used throughout the system both at the central equipment location
and at each area controller location to ensure a neat and tamper-free installation.
102
136.5
89
119
Lccal
Purchase
Lccal
Purchase
Local
Purhcase
Local
Purchase
Make sure that you use a standard key lock (for all sites). Standard unit dimensions
H440mm x W310mm x D110mm. Do not install wireless devices within these
cabinets unless a BNC or SO259 coaxial socket is provided (Model CAB-02).
33.5
33.6
33.7
N-PROTECT-RS485- Plug-In RS485 Signal Line Protection
These devices sit across EACH end of the RS485 bus and help prevent induced
01
voltage from blowing the Maxon driver microprocessors. Note that surges are
diverted to true earth and not to the system negative return bus.
(Novaris SL line
protectors)
When you order the device, ensure that you also get a piece of Din rail to mount it
on. The Din rail is then earthed.
Note. This item must be applied to each end of a SmartCare-1000 or Radiant1000 system RS485 cable run.
N-PROTECT LAN-01 Plug in LAN signal line protection
DIN rail mounting as above but intended for Ethernet LAN connection.
(Novaris SL CAT6
LAN line protectors)
N-240V MAINS
FILTER
Surge Protection device at input to all items requiring direct connection to
GPO mains.
Please source locally a good quality Surge protection device for all 240v ac mains
connected equipment.
Page 107
PART ‘Q’ – ANTENNAS
34. WIRELESS ANTENNAS
Item
34.1
34.2
Model
N-ANT-VHF-FLEXI
140-150Mhz
(Short range Paging
Antenna)
Description
‘Rubber Ducky’ 148Mhz PAGING ANTENNA
Approximately 15cm long it’s used for short haul coverage of typically 600M. To
overcome potential RF ‘swamp’ feedback into the low-level input cable into a paging
transmitter use a short length of coaxial 50Ώ coaxial cable between the Tx and
antenna..
N-ANT-VHF-297
140-150Mhz
(Long Range Paging
Antenna)
Unity Gain Whip Paging antenna
This is our standard paging antenna being a 1125mm stainless steel Whip that
requires no ground plane and typically provides a 3 to 4Km free space coverage
(depending on terrain). Designed for gutter or other external mounting arrangements.
It comes with 3.5M of 50-Ohm coax cable but without a fitted BNC connector.
34.2A N-ANT-BRACKET
34.3
34.4
34.5
34.6
Image
W/Sale $
RSP $
32
45
75
105
16
16
Right Angle Stainless Steel Mounting Bracket for Above
N-ANT-27S
25-30Mhz
27Mhz Antenna
26-29Mhz short haul whip Antenna suit WIC-02, 03 and WIC-05 Length 40cm
32
47
N-ANT-27M
25-30Mhz
27Mhz Antenna
26-29Mhz long range Antenna suit WIC-02, 03 & WIC-05 Length 1,000cm
42
65
32
45
38
53
N-ANT-304-FLEXI-01 UHF 304Mhz Flexi Antenna (Short haul direct connect)
304Mhz
Approx 25cm long this ‘Rubber Ducky’ antenna with BNC connector connects directly
to products such as the WIC-100, WIC-1000, UHF range extenders and the like. It is
generally used where range of sending devices is well within the scope of this
antenna, being typically 20M depending on building construction.
N-ANT-304-FLEXI-02 UHF – 304Mhz flexi Antenna (short haul direct connect)
304Mhz
As above but approx 35cm version Flexi antenna having slightly better range
capability.
Page 108
As Above
34.7
N-ANT-304-EXT
(Long Range
304Mhz Antenna)
(Want Range? Use
this antenna)
34.8
34.9
UHF-304Mhz External Antenna with Coax
For optimum UHF wireless range coverage this antenna becomes the ultimate
solution. Supplied with 3.5M of Coax cable this antenna is capable of receiving
standard 100μW 304Mhz transmitters/Pendants from up to 130M range in free
space. Mount as high as possible and it may present the best solution if mounted
within the roof cavity or external on the roofline. It has approximately twice the
reception performance of the Equipment mounted Flexi versions.
N-ANT-433-FLEXI-01 UHF 433Mhz Flexi Antenna (Short haul direct connect)
Approx 25cm long this ‘Rubber Ducky’ antenna with BNC connector connects directly
to the output of a Duralink Transposer and/or Duralink base station when not
requiring coverage over long of difficult building construction constraints. In
summary, it and its almost identical 304Mhz input antenna makes a neat solution to
small Duralink applications where, for example source to target paths are via plaster
walls and/or free space.
As Above
N-ANT-433-EXT
(Long Range
433Mhz Antenna)
As Above
UHF-433Mhz External Antenna with Coax
As above but for 433Mhz. Use these two (ANT-304-EXT and ANT-433-EXT)
antennas for Duralink
Page 109
75
105
40
55
63
89
PART ‘R’ – 26-29Mhz WIRELESS PRODUCTS & SYSTEMS
35. VHF (26-29Mhz) WIRELESS CALL-POINTS, PETs, RANGE EXTENDERS & SIMILAR DEVICES
Item
35.00
Description
Model
Legacy Explanation LEGACY 27Mhz WIRELESS PRODUCTS & SYSTEMS
Smart-Caller does not encourage or promote the use of low band VHF (27Mhz)
(All low band VHF
wireless nurse-call systems or products which, based on garage door opening
items are based on
techniques, were popular 20+ years ago.
Elsema protocol and The Company has however, assisted large numbers of Retirement Villages and
circuit modules)
Aged Care facilities throughout Australia and New Zealand to gradually retire such
facilities and in some cases have agreed to maintain those facilities with the supply
of replacement products and technical support.
This Section is dedicated to this subject; however we would not be prepared to install
new systems primarily as they cannot meet Industry expectations or Australian
Standards AS3811 and AS4607.
Image
W/Sale $
RSP $
Read Note
Read Note
27Mhz call traffic to ADEMCO Protocol Convertor
This central equipment optional item has been designed to capture 27Mhz wireless
traffic using the standard Elsema protocols (as used within OPSM, Village Watch,
Village Alert, Visiplex , Mical and other similar systems) and to convert those calls
into standard ADEMCO protocol for processing by Smart-Caller compatible nursecall host computer systems.
Note. Smart-Caller will require the use of a sample 27Mhz transmitter to verify
system compatibility. In this respect we no longer process Vitalcall call traffic.
Note. See Section 35 for 27Mhz products to support and/or convert legacy 27Mhz
systems.
494
578
27Mhz to Ademco and 304Mhz Protocol Convertor
This model is as the -01 version but includes an internal 304Mhz low powered
transmitter which effectively allows incoming calls (in addition to being converted to
Ademco format) but also to allow those incoming 27Mhz calls to be retransmitted
with unique identifying code for processing via various 304Mhz receivers such as
those within HP3 phones and HP4 Diallers for off-site delivery to central monitoring
companies.
For large sites with more than 48 incoming 27Mhz transmitters the Site-Wide dialer
should be used, each of which is capable of handling up to 256 unique incoming
27Mhz transmitters.
See Item 1.8 HP3-SITEWIDE-01 for more information.
525
698
NOTE. ALL 27Mhz PRODUCTS NOW SUBJECT TO AVAILABILITY - PLEASE
CHECK BEFORE QUOTING
35.1/26. N-WIC-05-01
1
(Capture 27Mhz (low
band VHF) call traffic
for nurse-call
computer processing)
35.2
N-WIC-05-02
(As above but with
304Mhz
retransmission
capability)
(Remember to
select two
antennas)
Page 110
35.3
N-TRX-03
VHF to VHF Repeater (Range Extender); (26Mhz - 29Mhz input and output
(Vhf to Vhf Repeater) carriers)
For existing systems using Elsema wireless codes i.e. to suit Village Watch, Village
Alert, Scanalert, OPSM, Visiplex, Mical and Vitalcall branded systems.
(Remember to select
antenna)
TRX-03 includes NiMH battery backup and plug-pack. It provides a SO259 (Screw
type) socket for antenna/coax lead connection but excludes 27Mhz antenna.
Note: Existing on-site repeaters used by all above brands (except Vitalcall) will
communicate directly with Smart-Caller head-end WIC-05 receiver/decoder unit. It is
necessary to replace existing Vitalcall repeaters with the TRX-03 for reliable
operation. If upgrading a third party system it is necessary to advise call-point and
retransmission carrier frequencies and to provide a sample call-point/pendant to
confirm system protocol at time of ordering.
420
559
105
144
105
144
105
144
Standard frequency for Smart-Caller systems is 27.145Mhz (Receive) and
27.014Mhz (Transmit). This overcomes ping-pong effect between multiple range
extender site. All range extenders and Transponders are supplied with battery backup, plug-pack.
35.4
N-CPR026-HAC-PC
(Wireless bedside
call-point, call and
cancel)
"H" series 26-29Mhz Call-Cancel call-point (Surface Mount)
26-29Mhz wireless call-point, call and cancel (no assist) with pendant cord socket,
including 9v ’snap-on’ alkaline battery all within 37mm mounting block
Standard frequency is 27.145Mhz
35.5
N-CPR026-HAC-01
(Wireless communal
call-point, call and
cancel)
35.6
"H" series 26-29Mhz Call-Cancel call-point (Surface Mount)
As above but without Pendant Cord socket.
N-CPR026-SPAC-01 26-29Mhz Call-Cancel Splash proof call-point (Surface Mount)
Two-button Waterproof (hooded) faceplate with 26Mhz call and cancel (no assist),
(Splash-proof callsplash proof within a 37mm enclosure, inc 9v snap-on alkaline battery all within a
point, call and cancel) 37mm mounting block.
Page 111
35.7
N-CPR026-SPA-01
(As above, call only)
35.8
~35.9
N-CPR026-UTIL-01
N-PET026-03
(Personal
Emergency
Transmitter PET)
26-29hz Call only Splash proof call-point (Surface Mount)
As above but with call only button (No Cancel)
26-29hz Call only Utility Call-point (Surface Mount)
26-29Mhz wireless call-point with blank face-plate and terminal block with 9v battery
within 37mm mounting block.
105
144
75
93
78
105
68
91
26-29Mhz Portable hand held transmitter
Two button Call and Cancel personal hand held transmitter with 9v snap-on battery
Depending on the antenna used on the Receiving device the range of this PET is
typically 100M in free space and from 10 to 80M in a building environment.
Range extenders exist to increase the range as necessary and typically up to 2Km..
Dimensions 81 x 56 x 24 mm. Standard frequency is 27.145Mhz
~35.10 N-PET026-04
(Personal
Emergency
Transmitter PET)
26-29Mhz Portable hand held transmitter
As above but with alarm button only (no cancel).
As Above
Page 112
PART ‘S’ – MOUNTING HARDWARE, SPARES, HANDBOOKS AND SIMILAR
36. TELEPHONE PRODUCT ACCESSORIES, MANUALS, HANDBOOKS & SPARES
Item
36.1
Model
A-KEY-SAFE-01
(Domestic External
key-safe cabinet)
Description
Key-Safe Cabinet with combination lock access
This is a most desirable accessory for any domestic situation where a person may be
at risk and wishes to allow authorized persons access without compromising home
security issues.
Image
W/Sale $
RSP $
21
32
19
32
9
14
9
13
11
16
11
18
Accordingly is a regular accessory item for our range of Emergency-Call phones and
dialers whilst also having many similar and general applications such as school kid
access.
36.2
36.3
36.4
36.5
36.5
A-KEY-SAFE-02DOOR
P-WMBBLUEPHONE
Wall mount to suit
Blue Phone HP3,
HP4 and Smart
Dialler HD4
P-HP2-WM-01
(HP2 Wall Mount
Bracket)
P-CURLY-CORD
HP3
Key Safe with combination that fixes to door handel or railing.
Wall mount to suit Blue Phone HP3, HP4 and Smart Dialler HD4
Due to entry of power connection on the phone base, standard wall mounting
brackets will not suit HP3 phones. It is therefore necessary to purchase this item if
wishing to wall-mount the product.
As a Mode-3 connection is normally required it is necessary to employ the services of
a ACMA Licensed installer to carry out the line connections.
HP2 Wall Mount Bracket (does not fit other than HP2.
As above but for HP2 model phones.
Handset Curly cord suit HP3 Phones
P-CURLY-CRD-HP2 Handset Curly Cord suit HP2 phones
Page 113
36.6
36.7
36.8
36.9.
36.A
P-BAT5V-HP/HD3
P-BAT6V-HP2
A-BAT-LITH-2032
[X1]
A-BAT-LITH-2032
[x20]
A-142-001
Battery pack suit HP3/Blue-phone & HD4 Smart-Diallers - NiMH 4.8v
16
26
16
26
3
4
37
63
24
32
12
20
3
4
6
10
8
13
8
13
Battery Pack suit HP2 Phones (6v Sealed Gel)
Panasonic Lithium 3v Batteries to suit all Pendants, call-points and similar
As above but in packs of 20 (Price per pack)
Important Note.
Note. It is important to use batteries as supplied in original equipment as it has been
found that the battery impedance characteristics within some (well known) battery
brands can be equipment incompatible with equipment operational requirements.
Replacement Battery for Ness 100-290 Range Extender. Ni-MH 8.4V
36.10 A-PENDANT-CASE
Replacement set of Plastics for Smart-Caller Wireless Pendants A
36.11 A-PENDANTLANYARD
Replacement Pendant lanyard for Smart-Caller Wireless Pendants
36.12 P-LINE-CORD
(Standard issue)
Standard Line cord to suit HP1, HP2, HP3, HD3 & HD4 Phones and Diallers
These are standard issue line cords identical to those supplied with the original
equipment.
36.13 P-LINE-CORD-6W
6-Wire Line Cord (RJ12-RJ12)
As Above
36.14 P-LINE-CD-6W-02
6-Way Line Cord (RJ12-RJ45)
As Above
Page 114
36.15
P-RFI-LINE/C-4W
36.16 P-RFI-LINE/C-6W
36.17 P-HP4-PP-RJ
WITH RJ
CONNECTION
36.18 P-HP3-HD4-PP-01
RFI phone line Filter 4 wire Line cord
This is an alternative version designed specifically for Medium Frequency RFI
suppression. We build the filter sections into a standard 4-way or 6-way line cord and
therefore include the cost of the line cord. It also includes the Ferrite-Bead listed
above within the price.
When ordering the line cord please give suffix –6W or 4W for 6 wire or 4 wire line
cords respectively.
25
35
30
40
15
23
15
23
24
32
Spare Decal for H Series Call Point
comes in CALL/CANCEL or CALL/CANCEL/PENDANT JACK
7
10
Spare Decal for Hooded Wet Area Call Point
Comes in CALL only and CALL/CANCEL
6
9
RFI phone line Filter 6 wire Line cord
As above but configured for a 6-wire line cord.
As Above
Blue Phone Power Pack with RJ CONNECTION (SWITCH MODE POWER
SUPPLY)
This switch mode power pack with RJ connection to the phone is required for the
HP4 Blue Phone
(Very early release HP4 have the older barrel type connection - linear power packs).
Plug pack – WITH BARREL CONNECTOR SUITS HP3, HP4 & HD4
(LINEAR POWER SUPPLY) 9v dc 300Ma
WITH BARREL
CONNECTION
36.19 N-STROBE-12V
36.19A N-DECAL-H-PC
36.19B N-DECAL-WP
Strobe light for HP3/HP4 and HD4 Phones and Diallers
One optional facility of the Emergency-Call phones and Diallers is the wireless
controlled Strobe light that would normally be placed at the entrance to the premises.
The wireless trigger transmitter located within the phone /dialer will remotely switch
on the strobe in an alarm condition and will switch it off when a cancel call is
dispatched. It is also possible to enable and disable the Strobe via key strokes on the
phone keypad.
It is usual to use an RDU-01 receiver (or other RDU models) to control the Strobe
activity. See Section 12 RDU devices
Page 115
36.20 P-USER HB-HP2
User Handbook for HP2
36.21 P-USER-HB-HP3P
User Handbook for HP3/Blue Phone (Professional version)
As Above
36.22 P-USER-HB-HB3D
User Handbook for HP3/Blue Phone (Domestic version)
As Above
36.23 P-USER-HB-HD4P
User Handbook for HD4 Dialler (Professional version)
As Above
36.24 P-USER-HB-HD4D
User Handbook for HD4 Smart-Dialler (Domestic Version)
As Above
36.25 P-MANUAL-HP3P
Technical manual HP3 Phone – Hard Copy (Soft copy free to approved persons)
As Above
36.26 P-MANUAL-HD3P
Technical Manual HD3 Dialler – Hard Copy (Soft copy free to approved persons)
As Above
36.27 P-MANUAL-HD4P
Technical Manual HD4 Dialler – Hard Copy (Soft copy free to approved persons)
As Above
Page 116
12
18
10
15
15
20
8
12
8
12
50
N/A
50
N/A
50
N/A
37. CURA MOUNTING HARDWARE, PLUG-PACKS, WRIST STRAPS & ACCESSORIES [GST Exempt & TGA Approved]
Item
37.1
Model
A-NBC-01
Pt No 2641-01
Description
Soft plastic unbreakable holder for desk-top placement- protects controller if it
falls
This non breakable housing is suitable for table top and will protect the controller in
the event of a fall. It also has a special quick release strap to allow fitting to a bed rail.
Illustrated controller module not included in the price.
Image
W/Sale $
RSP $
15
24
14
23
12
17
POA
POA
15
21
It is supplied with a flexible strap to allow it to be anchored such as fixing to a bed
rail. Also see bed rail bracket MB3 (next item)
37.2
37.3
A-MB3
Optional Metal Clip to suit all bed monitors
(Metal Clip for all bed This bracket fits to the back of the NBC-01 plastic enclosure to allow it to be
monitors)
conveniently clipped to a bed rail. The flexible strap that is supplied with the NBC-01
enclosure is also useful to secure the assembly.
A-CK-01 Caregiver
key
Pt No 2642
(Useful cancel and
system reset key for
many applications)
37.4
A-Plug-Pack12vdc
(Pt No 2404)
Carer Magnetic key-ring Cancel Key (Recommended Part)
No Cura based system should be without a number of these inexpensive key-ring
magnets. They are used to activate or deactivate the wireless tags and to cancel
active alarms at the Door Alert strip sensor and similarly cancel alarms generated by
other various equipment items.
Suggest purchase a few of these as they are used extensively as a low cost
means of resetting (cancelling) alarm conditions
Simply touch the correct location to switch on a resident’s wireless tag or to reset an
alarm in the strip or other sensor.
12v DC plug-pack.
Where nurse-call or door security system battery backed power source is not readily
available you should use this prescribed plug-pack which should be connected to a
dedicated 240v wall mounted power socket out of sight of Residents.
Note. For DoorAlert Systems (if not using nurse-call or security sourced power
supply use the special low EMI version in Item 3.5.
37.5
A-23A BATTERY 12V
12 v 23A Alkaline Battery
This battery is used throughout the Cura range of products primarily because the 12v
high ampere hour capacity within a small battery pack allows greater radio
(12v Alkaline Battery) transmission range without compromising product size.
Page 117
37.6
37.7
A-WRISTSTRAPWB-03
Pt No 2569
Patient Wrist Bands (Each)
A-WRISTSTRAPWB-03X10
Pt No 2569/10
Patient Wrist Straps (Packs of 10)
Spare Cord-Break USB connector links sections
To replace broken sections as used for hard-wired Cura Floor, Bed and Chair
sensors.
37.09 A-GCORD-01-1M
Pt No 2643
Interconnecting cord with two 6.3mm male jacks to connect controller to callpoint socket
socket. You may need to include a ADAP-02 or one of the multi-way adaptors shown
below if the bedside socket is pre allocated for an over-bed pendant or other device.
37.11 A-CURA
HANDBOOKS
13
80
118
25
30
21
32
21
31
POA
POA
As Above
37.08 A-BREAKCORDUSB
Pt No. 2480
37.10 A-GCORD-02-1M
Pt No 2643(RJ)
9
Interconnecting cord with 6.3mm male jack and an RJ12 to connect controller
to system
socket. You may need to include a ADAP-02 or 3 multi-way adaptors shown in
Section 17 if the bedside socket is pre allocated for an over-bed pendant or other
device.
As Above
Range of Cura Handbooks
Handbooks available to Agents on Web site and to others by request
Page 118
38. WANDERALERT SYSTEM REPLACEMENT PARTS AND SPARES
Item
38.1
38.2
38.3
38.4
Model
A-W101TX
(Wrist Tx)
Description
Wanderalert wrist (tagging) transmitter
Transmitter with wrist strap and battery
Image
A-W101TX/EX
(Refurbished Wrist
Tx)
Exchange (refurbished) wrist transmitter
Exchange units must be suitable for refurbish. Add $10:00 each if less than 3 units
per order.
A-WWB
(Spare Bands)
Wrist transmitter spare band with clips
OEM item. Base price is not determined by Smart Caller.
W/Sale $
RSP $
167
217
POA
POA
9
13
POA
POA
As Above
A-W101-RESONDER Wanderalert Controller/Receiver
AVAILABILITY - WHILST STOCKS LAST
IMPORTANT NOTE: The Wanderalert is a discontinued product and is
replaced by the DoorAlert products found in Part B Section 3 of this catalogue.
Please contact us for your ongoing requirements as we plan to assist
Wanderalert users wherever possible.
Page 119
39. SYSTEM CRITICAL CIRCUITS & COMPONENT SPARES
Item
39.1
39.2
39.3
39.4
39.5
39.6
39.7
39.8
Description
Model
N-ALARMCOM-PCB Serial input and Paging Encoder pcb
As used on ASM. AE16, AE32 Hard-wired Central equipment
Image
N-NETMASTER-PCB RS485 Master Controller Polling Circuit
As used on ASM and WIC-1000M Central equipment
As Above
N-AE16 BASE-PCB
Baseboard with 16 Krone connectors and components
To suit all standard AE16 central location and area controllers
As Above
Baseboard with 32 Krone connectors and components
To suit all standard AE32 central location and area controllers
As Above
Slave Area Controller Network PCB
Top suit AE16S and AE32S Area Controllers
As Above
Base circuit board with 304Mhz receiver module
To suit all WIC wireless units including WIC-100, WIC-200, WIC-1000M, WIC-1000S
As Above
N-AE32 BASE-PCB
N-NETSLAVE-PCB
N-WIC-BASE-PCB
N-MAX232N
(Microprocessor)
RS232 Send/Receive Microprocessor
Spare chips for all of the above Central equipment PCBs
N-MAX 483E
(Microprocessor)
RS485 Send/Receive Microprocessors
Spare chips for all Netmaster and net slave PCBs
Page 120
W/Sale $
RSP $
350
432
350
432
350
432
350
432
350
432
350
432
7
12
5
9
CATALOGUE /PRICE LIST - ISSUE 31 (01/09/2014)
CONDITIONS OF SALE
1. PRICES.
Quoted prices are FOB Melbourne with freight and insurance costs to the account of the purchaser.
All prices are subject to confirmation at time of ordering due to exchange rate variation and other matters beyond the control of Smart-Caller.
All prices exclude GST amounts, however GST exemption applies to many items as and where Identified.
No discounts are given or implied because separate prices have been listed for items that have quantity purchase discount capacity.
2. EXCHANGE RATES Quoted prices are subject to exchange rate variation. Prices may therefore be affected without prior notice.
3. PAYMENT Payment terms are:- payment with order unless credit arrangements have been established.
4. CREDIT TERMS
Credit terms will be subject to prior approval. 30 day terms shall provide for payment at the end of the month following the month of dispatch of the goods.
Further or additional supplies will not be dispatched should prior due payment be 5 working days overdue.
5. LEGEND "POA"
"TBA"
means "Price On Application".
means “To be Advised”. However, advice may depend on level of enquiries and may not otherwise be forthcoming.
6. GST EXEMPT
This price list excludes GST amounts. Total or sub systems may be supplied GST exempt by prior arrangement whereas some items are GST exempt as listed herein.
Refer to ATO determinations supplied separately for detailed information.
7. VALIDITY Prices and delivery information are subject to adjustment from time to time and shall, without notice, reflect significant changes to exchange rates and similar
charges
Beyond the control of Smart-Caller Pty Ltd. It is the obligation of the purchaser to ensure that the purchaser is using a current copy of the price list.
8. DELIVERY Delivery is subject to prior sales commitments and to the confirmed availability of new products and is therefore subject to confirmation at the time of ordering.
9. TITLE Smart-Caller Pty Ltd does not pass title to goods to the customer unless and until Smart-Caller Pty Ltd receives full payment without deduction or set-off, and the
goods
are delivered to the customer upon the condition that the customer holds the goods as trustee for Smart-Caller Pty Ltd until full payment has been effected.
10. SOFTWARE The supply of all software is on the basis of perpetual license ‘per single site’ and shall not be copied for use other than for the purposes of site specific
back-up purposes
11. WARRANTY The manufacturer's standard 12-month warranty applies to all Smart-Caller proprietary items. This warranty is limited solely to the free of charge repair or
replacement
of the defective goods returned to Smart-Caller at the customer's cost. Defective goods shall be goods that are defective solely due to faulty materials or workmanship.
12. DESCRIPTIONS Descriptions, specifications and images of equipment are intended for general information and are subject to change without notice.
Page 121
Page 122
Page 123
Page 124
Page 125
Page 126
Page 127
Page 128
Page 129
Page 130
Page 131
Page 132
Page 133
Page 134
Page 135
Page 136
Page 137
Page 138
Page 139
Page 140
Page 141
Page 142
Page 143
Page 144
Page 145
Page 146
Page 147
Page 148
Page 149
Page 150
Page 151
Page 152
Page 153
Page 154
Page 155
Page 156
Page 157
Page 158
Page 159
Page 160
Page 161
Page 162
Page 163
Page 164
Page 165
Page 166
Page 167
Page 168
Page 169
Page 170
Page 171
Page 172
Page 173
Page 174
Page 175
Page 176
Page 177
Page 178
Page 179
Page 180
Page 181
Page 182
Page 183
Page 184
Page 185
Page 186
Page 187
Page 188
Page 189
Page 190
Page 191
Page 192
Page 193
Page 194
Page 195
Page 196
Page 197
Page 198
Page 199
Page 200
Page 201
Page 202
Page 203
Page 204
Page 205
Page 206
Page 207
Page 208
Page 209
Page 210
Page 211
Page 212
Page 213
Page 214
Page 215
Page 216
Page 217
Page 218
Page 219
Page 220
Page 221
Page 222
Page 223
Page 224
Page 225
Page 226
Page 227
Page 228

PRICE WHOLESALE REV 31 PRICE 7-9-14Fin - Smart

Transcription

Similar documents

get protected! - Pine Cellular

Connecting Windows 8 to the Switch to the desktop - Crye

where merchant and mobile services merge

EXCLUSIVE SAVINGS FROM VERIZON WIRELESS.

exclusive savings from verizon wireless.

ascom telecaRE IP call modulEs ThE REAssuRAnCE oF A

USB 1.1 – A device interface to your PC that supports

NOVA Guest Wireless Network Portal

Ontario - SCADALink