NVIDIA Driver Configuration Instructions

Transcription

Nvidia Driver Configuration
Instructions
14.0
October 2013
Copyright
Copyright © 2013 Intergraph® Corporation. All Rights Reserved. Intergraph is part of Hexagon.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement;
contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade
secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from
Intergraph Corporation.
U.S. Government Restricted Rights Legend
Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was
developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with
subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal
Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of
the United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS
252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Intergraph Corporation
P.O. Box 240000
Huntsville, AL 35813
Terms of Use
Use of this software product is subject to the End User License Agreement ("EULA") delivered with this software product unless
the licensee has a valid signed license for this software product with Intergraph Corporation. If the licensee has a valid signed
license for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use
of this software product. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives
licensee permission to print a reasonable number of copies of the documentation as defined in the applicable license agreement
and delivered with the software product for licensee's internal, non-commercial use. The documentation may not be printed for
resale or redistribution.
Warranties and Liabilities
All warranties given by Intergraph Corporation about equipment or software are set forth in the EULA provided with the software
or applicable license for the software product signed by Intergraph Corporation, and nothing stated in, or implied by, this
document or its contents shall be considered or deemed a modification or amendment of such warranties. Intergraph believes
the information in this publication is accurate as of its publication date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable
technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.
The software discussed in this document is furnished under a license and may be used or copied only in accordance with the
terms of this license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not
supplied by Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL
EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.
Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data.
Users should verify for themselves that the data is accurate and suitable for their project work.
Trademarks
Intergraph, the Intergraph logo, and GeoMedia are registered trademarks of Intergraph Corporation. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Bing is a trademark of Microsoft Corporation. Google Maps is a trademark of
Google Incorporated. Pictometry Intelligent Images is a registered trademark of Pictometry International Corporation. ERDAS,
ERDAS IMAGINE, Stereo Analyst, IMAGINE Essentials, IMAGINE Advantage, IMAGINE Professional, IMAGINE VirtualGIS,
Mapcomposer, Viewfinder, and Imagizer are registered trademarks of Intergraph Corporation.
Other brands and product names are trademarks of their respective owners.
Contents
Certified Configurations ............................................................................................................................. 5
3D Vision Stereo LCD Display Configuration ........................................................................................... 7
Installing the NVIDIA 3D Vision Driver ............................................................................................. 7
Setting Up the Displays .................................................................................................................... 7
Configuring the Stereo Settings ..................................................................................................... 10
3D Settings for ISSD Using Driver 310.90 ............................................................................................ 13
3D Settings for ISSG Using Driver 310.90 ............................................................................................ 16
Configure 3D Settings for ISAT Multiphoto ............................................................................................ 21
3D Settings for ISAT Using Driver 310.90 ............................................................................................ 25
CRT Display Configuration ....................................................................................................................... 29
Setting Up the Displays .................................................................................................................. 29
Planar 3D Stereo Mirror Display Configuration ...................................................................................... 41
Setting Up the Planar 3D Stereo Mirror Display Hardware ............................................................ 41
Quadro FX 4600 ............................................................................................................................. 41
Quadro FX 4700x2 ......................................................................................................................... 42
Quadro FX 4800, Quadro 5/6000 ................................................................................................... 42
Quadro FX 5800 ............................................................................................................................. 44
Setting Up the Displays .................................................................................................................. 44
Configuring an Additional Monitor with the FX 4700 X2 (XP32/64 only) ........................................ 51
Tips for Optimum Stereo Performance ................................................................................................... 55
Windows 7 Considerations ............................................................................................................. 55
Technical Support and Information ......................................................................................................... 57
Self-Help Support Tools ........................................................................................................................ 57
Phone Numbers .................................................................................................................................... 57
Other Links ............................................................................................................................................ 59
Nvidia Driver Configuration Instructions
3
Contents
4
SECTION 1
Certified Configurations
AS OF THE IMAGESTATION 14.0 RELEASE, APPLICATIONS ARE NO
LONGER CERTIFIED FOR THE WINDOWS XP OR XP-64 OPERATING SYSTEM.
Configuration information related to those operating systems is for legacy versions only.
The following graphics card configurations were certified with ImageStation 6.2.1 and 13.0
using NVIDIA driver 266.45 on Windows XP, Windows XP-64, and Windows 7-64:
1 CRT 2 CRTs Planar
3D
Stereo
Mirror
Quadro FX 4600
X
X
X
Quadro FX 4700 X2
X
X
X
Quadro FX 4800,
Quadro 5000, 6000
X
Quadro FX 5800
X
X
Planar 3D
Single 3D
Stereo Mirror Stereo LCD
+ 1 mono
(CRT or LCD)
X
2
Dual 3D
Stereo LCD
3D Stereo
LCD + 1
mono LCD
X
X
X
X
X
X
X
X
X
X
3
X
1
X
X
X
1
Windows 7-64 only. Requires DisplayPort to DVI-D dual link adaptor cable.
Windows XP32/64 only.
3
Quadro FX 4800 and Quadro 5/6000 cards corrupt the display when exiting any orientations
(IO, RO, AO, Multiphoto) while running in the Windows XP32/64 environment with only one
stereo LCD monitor in use. The user must exit the application to clear the graphics. The problem
does not occur if running Windows 7-64, or if running Windows XP32/64 with a second monitor
attached.
2
The following graphics card configurations were certified with ImageStation 13.0 and 14.0
using NVIDIA driver 310.90 on Windows 7-64. Note that these are "K" series (Kepler)
Nvidia cards.
Single 3D
Dual 3D
Single 3D Stereo
Stereo LCD Stereo LCD LCD + 1 mono LCD
Quadro K5000, K6000
Quadro K2000, K4000
1
2
2
X
X
X
X
X
1
Dual 3D Stereo LCD
+ 1 mono LCD
X
X
Requires DisplayPort to DVI-D dual link adaptor cable.
Requires driver version 320.78. Follow same instructions as outlined for driver 310.90.
These cards do not have a 3-pin DIN connector for a stereo emitter and therefore will not
support stereo with CRT monitors.
5
Certified Configurations
Windows 8-64 users should use driver 320.00 or higher and follow the same
instructions as outlined for driver 310.90. As of this writing it is not possible to disable
Desktop Windows Manager in Windows 8, therefore stereo cannot be supported in the
Windows 8 environment at this time.
6
SECTION 2
3D Vision Stereo LCD Display
Configuration
A separate hardware driver is required for use of 3D Vision Stereo LCD displays for stereo
viewing.
Installing the NVIDIA 3D Vision Driver
1. Remove any previous 3D Vision drivers, if present, and reboot the system.
2. Install the NVIDIA graphics card driver.
3. Reboot.
4. Plug the 3D Vision stereo emitter into one of the system’s USB ports. If a 3 pin mini-din
stereo cable came with your 3D Vision kit, plug it into the stereo connector on your NVIDIA
graphics card.
5. Install the NVIDIA 3D Vision USB Stereo driver. Select the option to copy the files to
C:\Program Files\NVIDIA Corporation\NVIDIA StereoUSB Driver.
If you are installing driver version 310.90 this step is not necessary as the Stereo
USB driver is automatically installed with the video driver.
6. Reboot.
7. Configure the driver as described in the next section.
When the installation is finished and the driver is configured, the light on the emitter will glow dull
green. When a stereo application is started, the emitter will glow bright green.
Setting Up the Displays
1. Right click on the desktop and select NVIDIA Control Panel.
2. Select Set up multiple displays.
7
3D Vision Stereo LCD Display Configuration
3. For use with one LCD, select Only use one display (Single). For two LCDs, select
Configured independently from each other (Dualview):
8
4. Select Change resolution:
5. Set the desired Display resolution and Refresh rate for the first LCD, and click Apply. A
refresh rate of 120 Hz is recommended for stereo viewing.
6. Repeat for the second LCD monitor, if present.
9
Configuring the Stereo Settings
These settings pertain to ISSD and ISSG when using driver version 266.45 .
Click here for 3D Settings for ISSD Using Driver 310.90 (on page 13) and here for 3D Settings
for ISSG Using Driver 310.90 (on page 16).
1. Select Manage 3D settings.
2. From the Global presets list, select Intergraph ISSD:
10
11
3. Set Stereo – Display mode to On-board DIN connector (with NVIDIA IR Emitter).
4. Click Apply.
12
3D Settings for ISSD Using Driver 310.90
These instructions pertain to the Quadro K2/4/5/6000 graphics cards.
1. Make sure ImageStation Stereo Display is installed on the system.
2. In Manage 3D Settings, select the Program Settings tab.
3. Select Bentley Systems MicroStation.
4. Under Settings, make sure these features are set as follows:

Enable overlay is set to On.

Exported pixel types is set to RGB overlays (RGB555 format).

Set Stereo – Display mode to On-board DIN connector (with NVIDIA 3D Vision).

Stereo – Enable is set to On.
13
5. Click Apply.
14
15
3D Settings for ISSG Using Driver 310.90
1. Make sure ImageStation Stereo for GeoMedia is installed on the system.
2. In Manage 3D Settings, select the Program Settings tab.
3. Browse to GeoMedia.exe (default location is C:\Program Files (x86)\Intergraph\GeoMedia
Professional\Program):
16


Exported pixel types is set to Color indexed overlays (8 bpp).


5. Click Apply.
17
18
19
20
SECTION 3
Configure 3D Settings for ISAT
Multiphoto
This section refers to configuring driver version 266.45. Click here for 3D Settings for ISAT
Using Driver 310.90 (on page 25).
1. Make sure ImageStation Automatic Triangulation is installed on the system.
2. While still in Manage 3D Settings, select the Program Settings tab.
21
Configure 3D Settings for ISAT Multiphoto
3. Click Add:
22
4. Browse to isat.exe (default location is C:\Program Files\ISAT):
6. Enable overlay is set to On.
23
7. Exported pixel types is set to Color indexed overlays (8 bpp).
8. Stereo – Enable is set to On.
9. Select the setting for Stereo – Display mode according to the type of display you are using,
as described in previous sections of this document.
24
10. Click Apply.
3D Settings for ISAT Using Driver 310.90
2. From the Global presets list, select Base Profile.


Exported pixel types is set to Color indexed overlays (8 bpp).


25
4. Click Apply.
26
27
28
SECTION 4
CRT Display Configuration
1. In Windows XP, right click on the desktop and select Properties. In Windows 7, navigate to
Control Panel\All Control Panel Items\Display\Screen Resolution.
2. In Windows XP, select the Settings tab, and click Advanced. In Windows 7, click the
Advanced settings link.
3. On the Monitor tab, clear the Hide modes that this monitor cannot display checkbox:
4. Click OK, then continue to click OK on each dialog until the Display Properties dialog is
dismissed.
6. If prompted, select Advanced view.
29
7. Select Set up multiple displays:
8. For use with one CRT, select Only use one display (Single). For two CRTs, select
Configured independently from each other (Dualview):
30
10. Set the desired Display resolution and Refresh rate for the first CRT, and click Apply. A
refresh rate of 100 Hz or higher is recommended for stereo viewing.
11. Repeat for the second CRT, if present.
31
Some configurations may not yield the refresh rate that is desired even after disabling the
option shown on the previous screenshot. In that case, you must create a Custom monitor
configuration. To do this:
32
1. Click on the Customize… button at the bottom of the Change resolution dialog:
33
2. Click on Create Custom Resolution and accept the legal agreement that appears:
34
3. Enter the desired screen resolution and refresh rate, and set the Timing Standard to GTF:
4. Click the Test button. If the test is successful, save the configuration. Otherwise you can try
a lower resolution and/or refresh rate, keeping in mind that for stereo viewing you will want a
refresh rate of at least 100 Hz.
35
2. From the Global presets list, select Intergraph ISSD:
36
37
3. Set Stereo – Display mode to Use on-board DIN connector for both active and passive
stereo:
4. Click Apply.
38
39
SECTION 5
Planar 3D Stereo Mirror Display
Configuration
Setting Up the Planar 3D Stereo Mirror Display Hardware
The Planar 3D Stereo Mirror display system uses an add-in mirror card to accomplish 3D stereo
viewing. The In connector on the mirror card must be connected the graphics card. The Out
connector on the mirror card must be connected to the upper Planar monitor.
The following sections show you how to connect the cables for the NVIDIA cards that were
certified with the Planar display system.
Please note that the cards in the photos might appear "upside down" compared to your own
system. Use the 3-pin DIN stereo connector on the back of your card as a point of reference to
determine which way your cards are installed.
Quadro FX 4600
41
Planar 3D Stereo Mirror Display Configuration
Quadro FX 4700x2
Quadro FX 4800, Quadro 5/6000
42
Example 1: Using 2 DP ports:
Example 2: Using 1 DVI and 2 DP ports:
43
Quadro FX 5800
2. If prompted, select Advanced view.
44
3. Select Set up multiple displays:
45
4. For NVIDIA nView Display Mode, select The same on both displays (Clone):
46
6. Set the desired Display resolution and Refresh rate, and click Apply. A refresh rate of 60
Hz provides smoother stereo roaming than does 75 Hz.
47
2. Under Global presets, select Base profile:
48
4. Enable overlay is set to On.
5. Exported pixel types is set to RGB overlays (RGB555 format).
6. Multi-display/mixed-GPU acceleration is set to Compatibility performance mode.
7. Stereo – Display mode is set to nView Clone mode.
8. Stereo – Enable is set to On.
49
50
Configuring an Additional Monitor with the FX 4700 X2
(XP32/64 only)
1. Right click on the desktop and select Properties.
2. Select the Settings tab.
3. Highlight monitor 2 and check Extend my Windows desktop onto this monitor:
4. Set the desired Screen resolution for monitor 2.
5. If you desire to change the refresh rate, click the Advanced button and select the Monitor
tab.
51
6. In the configuration shown above, the Planar display will be the primary monitor. To make
the additional display the primary monitor, check Use this device as the primary monitor:
7. If you have physically placed the additional monitor to the left of the Planar display:
8. Drag the monitor 2 icon to the left of monitor 1.
9. Right click on the Taskbar at the bottom of the Planar display.
10. Uncheck Lock the Taskbar, if it is checked:
52
11. Place the mouse cursor over the Taskbar. While holding down the left mouse button, drag
the Taskbar from the Planar display to the additional monitor.
12. Reboot the system.
53
54
SECTION 6
Tips for Optimum Stereo Performance
As of this writing it is not possible to disable Desktop Windows Manager in
Windows 8, therefore stereo cannot be supported in the Windows 8 environment at this time.
Stereo views must not span monitors. Stretching a stereo view across two monitors will disable
hardware acceleration on the graphics card, severely impacting roam performance.
View windows must not overlap each other, as this can significantly affect the "smoothness" of
the roaming.
Do not allow dialog boxes or menus to overlap any views while roaming, as this can also affect
roaming.
Positioning the ISFC Active Feature dialog over the master stereo view does not seem to affect
roam performance. Other dialogs do affect performance, even when they are obscured by the
master window while roaming is active.
Windows 7 Considerations
To achieve the best performance when running stereo applications on Windows 7, you must
disable both desktop composition and Aero.
To disable desktop composition:
1. Open the Control Panel.
2. Click View >> Small Icons.
3. Click Performance Information and Tools.
4. Click Adjust visual effects.
5. On the Visual Effects tab activate the Adjust for best performance option.
6. Click OK.
To disable Aero:
1. Right click on the desktop and select Personalize.
2. Click on any one of the "Basic and High Contrast Themes."
The first time stereo is activated after logging in, any stereo application that spans two monitors
will be truncated to the primary monitor. Consequently, window layouts must be reconfigured.
This issue can be avoided by displaying any image with Rasview (from ImageStation
Raster Utilities) to trigger the stereo initialization after logging in. To enable this trigger in
Rasview, each user must create a registry entry by executing the text below in a registry batch
file (ex: filename.reg):
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Intergraph\ImageDisplayerLT]
"AllowStereoHw"=dword:00000001
55
Tips for Optimum Stereo Performance
Stereo views in ImageStation Stereo Display cannot be resized or moved. You must disable
stereo in these views, configure them as desired, and then re-enable stereo.
The NVIDIA driver control panel has an option for Stereoscopic 3D when installed on Windows
7. This option is not necessary for use with ImageStation applications and should be left
disabled.
56
Technical Support and Information
Intergraph provides several ways to access information and to contact support, including
self-help tools and phone support.
Self-Help Support Tools
Intergraph provides several electronic self-help support tools to answer your support questions
24 hours a day, 7 days a week.
1. Go to the SG&I Support page.
The first time you select this link, it displays the Intergraph Support page, and you
need to select Security, Government & Infrastructure Division to display the SG&I
Support page. When you select this link the next time, it will go directly to the SG&I Support
page. If you later want to change the division, click [Change Support Division] at the
bottom of the left panel on the Support page.
2. Under Product Support, select ImageStation from the Products drop-down list; then click
Go.
3. On the Customer Log In page, enter your user ID and password; then click Log In. If you
do not have a user login, click the link to request one.
4. On the product page, do one of the following:

Click Knowledge Base Search.

Scroll to the Product Versions table and click the download icon for the document you
want to read.

To read about new or enhanced features, click Release Notes.

To read about defects that have been fixed, click Issues Resolved.
Release Notes and Issues Resolved might not be available for the initial release of a
product because an initial release has all new features and no updated features. Some minor
releases might not provide Release Notes or Issues Resolved.
Phone Numbers
For general Intergraph information, please call 800.345.4856 (US). For worldwide support,
please contact your local Intergraph office. For North American Phone Support, please call the
appropriate number in the following table:
Portfolio / Product Family
Phone Numbers
Additional Information
Defense & Intelligence
Portfolio
800.661.8134
Monday – Friday, 7:00 a.m. – 7:00
p.m., CST

GIPS

GIES
57
Phone Numbers
Geospatial Portfolio
800.661.8134
p.m., EST
800.661.8134
p.m., CST
877.463.1217
p.m., CST

ECW

ERDAS APOLLO

ERDAS ER Mapper

ERDAS Extensions for
ArcGIS®

ERDAS Imagine®

ERDAS Other

LPS

Camera Systems

Digital Cartographic Suite

GeoMedia

GIS Imaging

ImageStation

IntelliWhere

MGE

TerraShare
Infrastructure Portfolio

G/Technology

FRAMME

InService
Public Safety Portfolio
58

BI Direct for CAD

BI Direct for WebRMS

BI Premium

I/CAD

I/LEADS

inPursuit

Video Analyst
24/7 support for P1 Critical System
Down problems
877.822.8921
877.822.8921
p.m., CST
Down problems
Phone Numbers
Security Portfolio
877.822.8921
p.m., CST

Security

EdgeFrontier

Video Responder
US Federal Customers
Down problems
800.633.7248
Email questions to
supportdesk@intergraphgovsolution
s.com
Other Links
To submit sales inquiries, general questions, and comments, please visit our Contact Us Web
page.
59

NVIDIA Driver Configuration Instructions

Transcription

Similar documents

3D Installation User`s Guide(English).hwp

TECHNICAL SPECIFICATIONS www.zotac.com

live performance console

Berl Senofsky, who died very recently, was born

AzureWave ARR5B95 Us..

RZR623 Fixing Wrong USB Devices in Windows 7

home theatre a / v selectors 5 way stereo speaker

TLAC-03212 Polaroid TV mss