Specification

Transcription

Specification

PRASAR BHARTI
BROADCASTING CORPORATION OF INDIA
DIRECTORATE GENERAL: DOORDARSHAN
SPECIFICATIONS
FOR SITC OF MEDIA ASSET MANAGEMENT
SYSTEM FOR ARCHIVING
Specification No.: SD 01/2013
Dated: 01.02.2013
1. SCOPE:
The specifications
aim at the
Supply,
Installation,
Testing
and
Commissioning (SITC) of the Integrated Media Asset Management System
consisting of following modules for the Archive cell of Doordarshan Kolkata:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Tape Playback
System
(VCRS1Decks will be provided
Doordarshan)
Analog to Digital convertor cum audio Embedder
Standard Noise Reducers
Advanced Digital Restoration System
32 x 32 HD/SD-SDI Router System
Software based Restoration on NLE Systems
Media Asset Management System
Ingest System and Browsing System
LTO 6 based deep Archive system
NLE with 3D for Repurposing alongwith DVD/Blu ray Authoring
UPS
by
2. TURN-KEY IMPLEMENTATION:
a. The Supply, Installation, Testing and Commissioning of the Archive
system should be implemented on turnkey basis.
b. The bidder should have a proven track record of design and installation of
full featured Archive system for broadcast applications and should have
work experience of designing & installing at-least two Media Asset
Management
system projects for Archival applications
to leading
Broadcasters in the last four years prior to the submission of the bid. The
cut off date for the experience shall be the date of submission of the bid.
The bidder not having the requisite work experience may tie up with other
partner with requisite work experience as mentioned above. In this case,
the partner will be responsible for carrying out design, installation, testing
& commissioning
of the facility. The MoU of partnership to this effect
should be submitted along with the bid. However, this MoU does not
Specifications for SITC of Media Asset Management System for Archiving:
SD 01/2013
dt. 01.02.13
Page 1 of 42
absolve the bidder from successful completion of the SITC job as per the
terms and conditions of the tender. The list of similar turnkey works
successfully done by the bidder/partner in the past 4 years with full
details should be enclosed along with the bid. The supporting
documentary evidence like work order with successful completion
certificate should also be submitted along with the offer. The offer(s) from
the bidder not having the requisite work experience will not be considered.
c. Keeping in view the complexity & integration of various type of equipment,
a pre-bid conference will be held at an appropriate time before the last
date of the submission of the bid to bring clarity to all the prospective
bidders in respect of the requirement of tender specifications. The date
and venue will be intimated to all the prospective bidders separately. The
prospective bidders are required to submit their queries (if any) in
writing so as to reach Doordarshan at least three working days before
the pre-bid conference.
d. It will be the responsibility of the bidder to ensure after-sale service and
guarantee for all equipment from respective manufacturers. The bidder
has to ensure that the guarantee is extended by the OEMs of all hardware
and software of entire archive system as per the guarantee clause
specified in the tender.
e. Being a SITC project, the archive system should be fully configured and
hardware & software customized to the required workflow of Doordarshan
Archive cell of Kolkata.
f. Doordarshan Kolkata will provide accommodation for housing the
complete Archive system.
(i) The facility will be installed in the second floor of Second Channel
Building at Doordarshan Centre, Kolkata. The layout showing
dimension of the rooms is enclosed in the Appendix - III. The bidder
should workout the area required for installation of the proposed
facility as per their system design. A layout plan for installing various
equipment should also be submitted along with the bid.
g. The integrator has to offer suitable Precision AC for Server Room of
reputed manufacturer. The bidder has to provide relevant details of
service support along with the bid. The tonnage calculation along with'
heat load details, CFM requirements and the layout diagram should be
submitted alongwith the bid.
h. Doordarshan will provide three-phase power supply (phase to neutral 230
volt ±5%, @50 Hz) at single point in the facility. Further distribution to
the various equipment, working desks etc. has to be planned and
executed by the bidder. The successful bidder will be required to submit
the power supply distribution schematic to Doordarshan for approval
prior to execution of the work. The provision of all electrical items
required for the facility should be included in the bid.
Specifications for SITe of Media Asset Management System for Archiving: SD 01/2013 dt. 01.02.13
Page 2 of 42
(i) The bidder needs to provide 40 KVA three-phase on line UPS with 30
minute
backup
in (1+ 1) load sharing
mode from reputed
manufacturer. The bidder must ensure that service support for the
offered UPS is available locally.
(ii)The inrush current of the offered UPS should be carefully chosen to
take care the nature of the load.
(iii)It is envisaged that the total electrical load of the System with
adequate head room will not be more than 40 KVA. In case 40 KVA
capacity is inadequate, a UPS system of higher rating should be
offered. The bidder should also provide the electrical load calculation
of the offered system.
(iv)The accommodation is already equipped with house lights. However,
special lights for proper illumination of operation desks and
equipment racks should be provided by the bidder.
1. The equipment offered for this project should be proven products from
well-known and internationally reputed manufacturers, who have proven
records of offering high-class & high MTBF equipment.
J. Any substandard equipment included in the offer may cause rejection of
the complete offer with the sole responsibility of bidder.
k. The power cables to be used for internal wiring for various purposes
should be fire retardant and of the best quality having adequate rating
with sufficient headroom.
1. The bidder has to use high grade cables & connectors for video, audio,
data and power interconnection of various equipment. The HD video cable
should be similar to Belden 1855 for rack wiring and Belden 1505 &
1694A for other applications. The HD BNC connectors of high quality
should be used. High quality XLR connectors, similar to Neutrik make
should be used.
m. The relevant details like various parameters, calculation details, layout,
drawings, technical furniture design, rack layout etc. considered while
designing the system should be provided alongwith the bid.
n. The successful bidder will be required to prepare and submit the final
system design and technical furniture design in consultation with
Doordarshan and get it approved by Directorate General, Doordarshan
before actual implementation.
3. GENERAL FEATURES:
The tapeless workflow is required for Doordarshan's archive cell at Kolkata.
It is envisaged to ingest the existing program content of U-matic, Betacam
SP, DVCPR050 and XDCAM HD422 formats stored on tapes/optical disc
media into the system, in file format of high resolution and low resolution
quality. After adding metadata, the hi-res content is to be transferred to LTO
Page 3 of 42
tapes. The workflow of the Archive system consisting of various components
and their necessity is described below:
a. Broadcast quality Time Base Correction (TBC) units 3 nos are to be
offered for the content to be played from U-matic players. TBC/DTBC
units offered should be rack mountable and have analog composite
input/ output.
b. The baseband video and audio contents from VCRs of analog format
should first pass through Analog to Digital Converter cum audio
embedder. ADC should accept analog audio. The output of the ADC
should routed to various equipment through 32 X 32 HD/ SD-SDI routing
switcher. Output of Digital VCRs/Deck will be directly routed through the
router.
c. A 32 x 32 HD/SD-SDI Video and machine control protocol routing
switcher for routing HD/SD-SDI video with embedded audio and also the
machine control (RS232/RS422) of various playback, restoration and
authoring equipment.
d. It should be possible to pass the SD-SDI signal through card based
Standard Noise Reducers selectable through the Router for removal of the
basic noise & artifacts and for signal enhancement, if required.
e. The output of VCRs/Players/Decks should be made available through the
router to high end Digital Restoration system for restoration and removal
of various timing errors & noise impairments, if required. The frame by
frame restoration and noise reduction should be possible. The restored
video & audio outputs should be ingested into MAM's online storage.
f. It should be possible to route the Audio and Video contents needing minor
correction/restoration,
to the NLEs storage in uncompressed format for
restoration and noise correction.
.
g. Noise corrected and digitally restored contents available in the NLE
storages shall be authenticated by the Administrator through a dedicated
Quality control system for ingesting into the online storage of MAM
system.
h. The ingest operation will transfer the content stored on tapes/optical disc
of U-matic, Betacam SP, DVCPR050 and XDCAM HD422 format to the
online storage in file format over i-Link/firewire/Gigabit
Ethernet
interface or directly through base band without degradation of quality. Six
numbers of ingest workstations are envisaged. Two nos. will be used for
ingest of DVCPRO 50 and/or XDCAM HD422 content over firewire/iLink/Gigabit Ethernet, two nos for ingest of U-matic format base-band
video and audio signals after A/ D conversion and two nos for ingest of
Betacam SP format base-band video and audio signals after A/D
conversion. The bidder should offer bi-directional codecs supporting DV,
DVCPR050, MPEG2 up to 50 Mbps (both I frame and long GOP), XDCAM
HD422 1920xl080 50Mbps PALformats.
Specifications for SITC of Media Asset Management System for Archiving: SD 01/2013 dt. 01.02.13
Page 4 of42
Low resolution media content is to be generated for browsing and
metadata creation. The transcoder(s) is/are required to automatically
create low-resolution content from the ingested high-resolution content.
The browse quality of A/V content should be frame accurate and available
in H.264/WM9 format quality at user selectable data rate up to 1 Mbps.
The transcoding system should be faster than real-time or growing file
ingest and designed in such a way that the transcoded low resolution
material should be available within one hour after ingestion of the full
resolution content in the peak load condition. Each ingested program
content can be taken as I-hour duration for this purpose. The bidder
should explain the calculations undertaken to arrive at the quantity of
transcoders required.
J. The high resolution content ingested will be stored on the -online storage
system. For this purpose, a total storage of 30 Terabytes should be
provided in the form of Fe storage array with SAS HDD employing RAID
5/6 configuration. Out of 30TB storage, 20TB will be used for lowresolution material storage and 10TB will be used for the high-resolution
material. The storage system should be easily expandable in multiple
chassis.
k. Six numbers of dedicated browsing & metadata creation terminals should
be connected with this system. These terminals should be equipped with
high quality headphones to meet the functional requirement. It should be
possible to configure the Ingest terminals to work as a preview terminal/
browsing & metadata creation terminal, whenever there is no Ingest
activity.
1. The Archive system should work under a powerful, comprehensive and
enterprise class MAM system. The offered MAM solution should be field
proven and in use by international broadcasters. The bidder should
1.
essentially enclose the international broadcasting user list along-with
the tender. An industry standard Database engine supporting SQL or
Oracle or DB2 database system should be part of the MAM. The Media
Asset Management is the core of the system and should take care of
ingestion, metadata creation, browsing, search, tracking, transcoding,
frame accurate proxy generation, movement of the content and end to end
content management functionalities in the envisaged workflow including
Hierarchical Storage Management (HSM). It should be able to link tape
based/tapeless content, low resolution copy, metadata, full resolution file
copy and different instances of the material. It should be integrated with
data tape library / nearline storage system, a postproduction system, low
resolution edit, DVD & Blu Ray authoring system etc. The core functions
of MAM should be fully integrated ones, with minimum recourse to the
third party solutions. The MAM system should have tight and seamless
integration with powerful leading content management system. The
offered MAM system should be upgradable in future. The bidder should
Page 5 of 42
explain the workflow with the help of various MAMmodules, in full
detail.
m. The system in addition to manual metadata creation, should allow
importing of metadata from other similar systems and also existing
central archive system of Doordarshan (Dalet MAMsystem). The metadata
insertion should be possible for entire video or for any portion of a clip.
The metadata field should be scalable and should be customised
according to the end user's requirement.
n. One number of NLE with 3D graphics system should be provided and
integrated with the MAM's online storage system for repurposing
requirements. The bidder should quote the required DVD and Blu Ray
authoring software module for this purpose. The output of this system
should be connected to the AVe router so that this repurposed content
can be recorded in VCR/Deck. The proposed 3D Computer graphics
system should be networked to the NLE meant for Graphics generation
and compo siting purpose. The offered 3D Graphics software should be
similar to Softimage XSI or 3ds max or Maya with compositor.
o. The bidder should supply UPS of suitable rating for the complete Archive
system. The bidder should enclose the required load calculation details for
substantiating the UPS rating.
p. The bidder should offer reputed brand and high quality Amplispeakers for
near field monitoring for the following systems:
• Software based restoration on NLE systems - 2 Nos.
• Advanced restoration systems - 1 No.
• Quality control (Supervisor) terminal- 1 No.
• DVD authoring on NLE & 3D Graphics system - 1 No.
• Preview System - 4 Nos ( Preview VCRs will be provided by
Doordarshan) .
q. In addition to the audio monitoring, one video wall with 55" LED Monitor
fed from 16 input
Multiviewer system (broadcast quality) should be
provided along with the QC system. The video wall displays the media
outputs of all systems.
r. Each and every offered equipment should be from internationally
reputed manufacturer and the quoted model should be field proven
and in use by leading broadcasters in various continents of the
World.The bidder should essentially submit the list of such leading
broadcasters to whom the quoted model has been supplied.
s. The bidder should supply software pertaining to all equipment in their
original media duly licensed in the name of Doordarshan with perpetual
validity. Necessary documents pertaining to the licenses for various
systems of the overall project should also be submitted.
Page 6 of 42
t. The
make
and
model/part
no.
of
each
and
every
equipment/item/installation
material etc. should be clearly mentioned in
the offered Bill of material.
u. The Bill of material (BOM)has been provided in Appendix-I. The bidder is
required to provide the complete list of equipment,
software and
accessories etc. including the technical furniture offered to meet the
specification requirement.
The quantity of each item including submodule etc. are to be specified clearly and compulsorily, failing which the
bid will liable to be rejected summarily. The following is the proforma for
the BOM:
S.No.
1.
Description/
Name of Item
2.
Make
Model
3.
4.
Part
any
No., if Qty.
5.
6.
v. In order to ensure the completeness of the system, any additional
equipment/ accessories which bidder feels necessary to complete the
configuration should also be quoted as an essential item.
w. The bidder shall submit only one solution (Single BOM) for the offered
system. BOM shall not contain any alternate item/items for the item
mentioned in the BOM. Bid with alternate item(s) is liable to be rejected.
x. The bidder should indicate reliability of the storage, restoration equipment
and all the sub-system in the workflow.
y. The indicative block schematic diagram for the Archive System is as per
the Appendix-II.
4. ACCOMMODATION:
a. The facility will be installed at Doordarshan TV Centre located in Kolkata.
b. Details of the available space are given in Appendix-III. The layout should
be so designed as to maximize the utilization of the available space
without compromising the functional requirement. Bidder is required to
provide the equipment layout plan of full system with dimension, along
with the bid.
c. The bidder is required to visit the site for assessment of space available,
distance between various rooms, various cable routes, cavity flooring (only
for server room) any working day between 10:00 AM to 06:00 PM, before
submitting the bid. The bidder may contact the Dy. Director General
(DDG), Doordarshan Kendra, Kolkata (Tel. No. 033-24235656) for the
purpose. In case bidder misses out certain details in his offer and it is
found that his offer is incomplete, the bid will be rejected on sole
responsibility of the bidder.
Page 7 of 42
5. POWER SUPPLY AND AIR CONDITIONING:
a. Doordarshan will provide three-phase power supply (phase to neutral 230
volt ±5%, @50 Hz) at single point in the facility. Further distribution to the
various equipment, working desks etc. has to be planned and executed
by the bidder. The successful bidder will be required to submit the power
supply distribution schematic to Doordarshan for approval immediately
after award of the work. Power Distribution Panel with the required
switchgears like Bypass switches, MCCBs, MCBs, Phase sequence switch,
digital Phase sequence meters, digital Volt and Ampere Meters, digital
frequency meters etc. should be provided. The required numbers of Sub
Distribution Panels should also be provided. The entire Switch Gears
should be of high quality and should be of reputed brands. The cost of all
electrical items like power cables, connectors, MCBs etc. required for the
facility should be included in the offer.
b. It is envisaged that the total electrical load of the System with adequate
head room will not be more than 40 KVA. The bidder needs to provide 40
KVA three-phase on -line UPS in (1+ 1) mode with 30 minute backup on
full load from reputed manufacturer. The bidder must ensure that service
support for the offered UPS is available locally at Kolkata.
c. Mains and UPS Power Supply status (Aural & Visual) indication should be
made available in the Operational Area through Remote Monitoring
Facility. It should be clearly visible and audible.
d. All the power supply equipment like LT panel, Distribution box, UPS,
battery bank etc. are part of the offer.
e. The accommodation is already equipped with house lights. However,
interior of the technical area for proper illumination of operation desks
and equipment racks should be fitted with aesthetically designed script
lights. Adequate quantity of compact fluorescent light (CFL)j LED light
fittings to give proper illumination needed for operation and maintenance
should also be offered. This will also include the required cabling etc.
f. Technical and power earthing for Video, Audio and Power equipment
including for UPS should be properly done as per the standard.
g. It is essentially required from the integrator to give the calculation of the
estimated heat load for the total requirement of air conditioning in all the
technical area envisaged under the tender.
h. The requirement of air conditioning in server room is estimated to be
about 6 TR. The temperature inside server room should be maintained
between 18 to 20 degree Celsius and relative humidity should be
maintained between 40 to 50%. The precise temperature control, humidity
control, up-flow and down-flow configuration
and multi-flow air
distribution systems for uniform cooling should be offered. The bidder
should offer Precision air conditioner of reputed manufacturer for server
room.
1. For other areas, air conditioners of sufficient tonnage capacity will be
provided by Doordarshan.
Specifications for SIre of Media Asset Management System for Archiving: SD 01/2013 dt. 01.02.13
Page 8 of 42
6. ESSENTIAL FEATURES OF ARCHIVE SYSTEM:
6.1 ADC & AUDIO EMBEDDER
a. As the U-matic and Betacam SP players provide analog video and audio
outputs, the bidder should offer five numbers (four in analog chain and
one spare) of reputed make card based Analog to Digital Converter cum
audio embedders mounted in rack frames.
b. The offered system should have 10-bit broadcast quality Video encoder
employing 12-bit quantization for analog to digital conversion of Video
signal and 24-bit resolution for analog to digital conversion of audio
signal.
c. These cards should embed four digital converted audio signals and
offer adjustable gain and delay of the audio signals. The audio signal
being embedded with the SDI video should be in sync (lip sync) with
the respective video so that there is no delay between the video and
audio.
d. The unit should facilitate adjustment of Horizontal and Vertical timing
and other Processor Amplifier controls required for the video signal.
The card should has the facility for external reference signal input.
e. The required reference signal generator and distributor may also be
offered. The reference signal should be distributed to the relevant
equipment such as ADC, Players/Deck, Router etc.
f. The bidder should offer required quantity of rack frames along with
dual redundant hot swappable power supplies. The Rollcall software for
remote monitoring and adjusting the parameters of video and audio
signals should be provided and loaded on the ingest system or on a
dedicated PC with configuration as recommended by the OEM.
6.1.1 TECHNICALSPECIFICATIONS
1.
2.
3.
4.
Video Quantization
Decoder
Audio Quantization
Controls
: 12-bit for Analog to Digital conversion
: Adaptive Comb Filter
: 24-bit ADC resolution
: Horizontal & Vertical timing, Video &
Audio gain control
6.2 ROUTING SWITCHER
a. The bidder should offer internationally reputed 32 X 32 Video routing
switcher. It should be capable of routing the HD-SDI & SD-SDI signal
with embedded audio and simultaneously controlling the respective
players/Decks through RS232/422 machine control protocols.
Specifications for SITe of Media Asset Management System for Archiving:
SD 01/2013 dt. 01.02.13
Page 9 of42
b. The routing switcher facilitates effective utilisation of various resources
by assigning any of the sources to required destination.
c. The routing switcher should be wired to route media content from
various sources like all Legacy & other VCRs/Decks, restored outputs
of advanced digital restoration system and media contents from the
NLEs to various destinations like Ingest systems, Advanced digital
Restoration System, NLEs with software based restoration system and
Recorders/Decks for Print to Tape.
d. The bidder should provide one no. of XY remote control panel and 10
nos. of Single bus remote control panel for each destination which will
facilitate the user to choose the required source. It should be possible
to control the selected player/VCR/Deck by the user from the
operation desk.
e. The router should have the facility to marry the input ports for
selecting the input and output simultaneously for monitoring the
quality enhancement from standard noise reducer and advanced
restoration system before ingesting to the online storage of the MAM.
f. The router should be rack mountable and should have dual redundant
power supply.
g. The bidder should provide HD compatible Video patch panels. All
inputs and outputs of routers, ADC cards, SNRs and other equipment
connected in the system should be terminated to the video patch panel
for facilitating manual patching and routing of various sources in case
of failure of the routing switcher. A suitable facility for patching the
machine control (like Ethernet patch panel) should also be provided.
h. The XY control panel should be suitably connected to the
Administrator / Quality Control system for remotely monitoring and
configuring the router.
6.3 STANDARD NOISE REDUCER
a. The offered Standard Noise Reducer (SNR) system should have high
reliability and broadcast quality signal processing capability. This
should be capable of reducing different type of timing errors and noises
mainly originating from old tape machines of different formats like Umatic, Betacam SP etc.
b. The bidder should offer five numbers of card based or stand alone
Standard Noise Reducer system which should accept and deliver SD-SDI
signal with embedded audio. 4 nos will be connected in the circuit and
remaining one will be used as stand by.
c. The system should be able to reduce jitter and provide stable output
signal. The system should be able to achieve an overall improvement in
signal to noise ratio over the input signal.
d. The unit must have distinct set of filters, each addressing to a specific
noise with ability to control the parameters. Broadly, filters for following
Page 10 of 42
types of noises and artifacts should be provided with appropriate
algorithm to reduce them without the loss of spatial resolution of
original signal.
~ Random video noises in spatial and temporal domain.
~ Impulse noises that of drop-outs black/white spots.
~ Subcarrier artifacts such as co-related luminance & chrominance
noise.
e. It should provide the facility for compensation of sharpness of edges etc.
with separate controls for luminance, chrominance and coring. This
process should ensure that no overshoots/ ringing are introduced in the
output signal.
f. The unit should have dedicated control panel or should be remotely
controlled through rollcall software for user to control various
parameters like Luminance gain, Chrominance gain, Black level, Y/ C
timing, picture position, blanking, Noise threshold, strength and H & V
details enhance. It should also have input and output audio gain control
and internal audio delay through inbuilt audio delay processor for
ensuring perfect sync with processed video signal in auto delay track
mode.
g. The output of the SNR will be available for ingest to the MAM,Advanced
Restoration System or Software based Restoration System as per
requirement. The facility for bypassing the standard noise reducer
should also be possible.
I. VIDEO PERFORMANCE
1) Signal processing
2) Standard
II. INPUT
1) Video input
2) Return loss
3) Audio input
III. OUTPUT
1) Video output
2) Return Loss
3) Jitter
: 10 bits 4:2:2 component digital video (ITU-R601)
: PAL/SDI SMPTE 259M
: SD-SDI - 1 no or more on 75 ohms,
connector
: > 15 dB, upto 270 MHz for SD-SDI
: Embedded
BNC
: SD-SDI with embedded audio/ 800 mVp-p, 75
ohms on BNC, 270Mbit/ s, 4:2:2 serial component
digital - 2 nos.
: > 15 dB, upto 270 MHz
: < 0.25 VI.
Page 11 of 42
6.4 ESSENTIAL FEATURES OF NON LINEAR EDITING SYSTEM
a. Three numbers of NLEs are envisaged for this Archive system. Among
these, two NLEs should be loaded with restoration softwares for video
and audio respectively. The uncompressed media content SD-SDIjHDSDI available from player jVCRjDeck through router will be ingested
through NLE's captured card and stored in attached storage system. The
restoration software will perform removal of noises and restoration of the
media content. This restored content will be transferred to Online
storage system of MAMthrough ingest operation.
b. Though the NLE systems envisaged for this project is meant for working
on the file based contents, the system should have the facility to accept
and deliver base band signals through dedicated break out box. The
offered NLE systems should have analog components, composite, SDSDI and HD-SDI video inputs and outputs conforming to PAL standard
and their respective analog and AES audio input and outputs for
standalone operation also.
c. The NLE systems should allow multiple file conversion e.g. AVI,WMV,
Q-time etc. It should allow capturing and publishing of XDCAMHD422
MXF data files in native file format through USB 2.0j3.0, Ethernet and
FireWirej I. LINK interface. It should therefore be equipped with USB
2.0j3.0, Ethernet and FireWirejI. LINKinterfaces.
d. The third NLE system with 3D Graphics system is a standalone system
with its own media storage and meant for repurposing the media
contents residing in the Online storage or content retrieved from the
Nearline storage (LTO Tapes). This NLE performs the function of DVD
and Blu Ray Authoring also.
e. The offered hardware and software solution for NLEs should be fully
integrated for the best performance. The hardware configuration of the
NLEs should meet the requirements projected by the OEM and must be
the latest available in the fast changing IT market.
f. The offered NLE system should have real-time architecture and should
have the capability of real-time simultaneous playback of two HD-SDI,
four 10-bit SD-SDI uncompressed video streams and four graphics.
layers. Only moving video will be considered for counting video streams.
g. The system should have all the functions of standard high quality
reputed brand NLEs available in the broadcast industry which support
editing of uncompressed HDjSD-SDI signals in real time. The editing
software should be capable of generating various transition effects like
classical box, diamond & circular wipes, rotary, tilt & slide wipes and
dissolves with variable softness, border colour and border width. The
system should provide unlimited videoj graphics layers in fast rendering
mode.
Page 12 of 42
h. The editing system should have various motion effects like freeze frame,
field interpolate, slow & fast motion, strobing in forward & reverse etc.
1. The system should have facility for real-time color correction. RGB
controls of hue, saturation,
contrast, gamma, gain and offset
adjustments
should be in real-time. Colour effects like negative,
posterization, solarization and tint should also be present. Selective
correction of highlights, mid-tones or shadows and advanced color
selection matching should also be available. The system should have
frame buffer for precise color comparisons.
J. The editing system should provide real-time 3D DVE effects which
includes X, Y and Z axis rotation, Perspective, Picture-in-Picture, Mosaic
and Image Blur, Colored and Textured Borders, Drop Shadows, Border
Outlining, Posterization, Matte, Fills, Freeze Frames etc. 3D DVE effects
like page tum, warp, lighting and perspective ripples, tilts, zooms, and
rotating cubes etc. also should be possible.
k. The system should also have integrated facility of 3D text creation. The
system should also provide real-time rolls and crawls of the text.
1. The system should have character generation facility in all major Indian
languages apart from English. Character generation should have a wide
range of colours for texts, edges, backgrounds etc. Different fonts types
including user definable are also to be made available (scalable fonts
with drop offset or extrude shadows and outline) along with glow or
embossing effects. The system should have independent character
adjustment of transparency, fill, shadow, outline, underline, bold,
italics, kerning and axis control.
m. Integrated real-time luminance and chrominance keyer should be
present apart from having a graphic title keyer with keying facilities like
alpha channel keying, luminance based keying, digital chroma keying,
overlay hard keying etc. The system should offer basic compositing
features.
n. The offered system should support interoperability for EDL import and
export. It should also support meta-data formats such as MXF, AAF to
enable interchange of projects and media files with other editing system
in the network.
o. The system should be capable of controlling VCRs with RS-422 port
using the Sony /GVG VTRcontrol protocol.
p. It should be possible to do Jog/Shuttle operation from the keyboard.
Extemal Jog/ shuttle controller should also be offered.
q. Facility for frame by frame trimming should be available for accurate
edits.
r. Split, cutaway editing, A/B roll editing, trim mode and transition mode
editing, many levels of undo and redo etc. should be possible. Levels of
video and audio should be independently adjustable during the editing
Page 13 of 42
s.
t.
u.
v.
w.
x.
y.
z.
process. The system should have clip editors and cut editors with
storyboard.
The system should support at least eight camera editing. It should be
possible to switch the captured sequences from eight camera angles in
real-time.
The audio signal processing should also be in digital domain with the
possibility of having multi track audio mixing facility. This facility of
audio processing include multi band equalization, echo, reverb, time
scaling and multi track wave edit facility. The audio processing should
be up to 24 bit sampling. The NLE systems meant for Restoration
purposes should have reputed audio restoration softwares like Sequoia,
Cedar and Cube-tee along with suitable hardware.
The system should have many pre rendered effects like perspective,
speed change, reverse variable speed playback, cropping, keying,
warping, transparency, 2D and 3D transitions etc.
All the necessary features described above such as CG, DVE etc. should
be accessible within the main editing application software without
switching from one program to another.
The print to tape and DVD/Blu ray burning should be possible directly
from the time line. Necessary DVD/Blu ray authoring system should be
offered.
The edited video should support other image formats such as AVI,
Softimage (.pic), Quick Time, TGA, SGI, PCX, BMP, GIF, Alias, JPEG,
Photoshop, and TIFF etc. It should also have unlimited number of bins.
The system should have project and asset management capabilities
such as multi level find and sort functions as well as frame and text
VIews.
The system should have 3-point editing with unlimited lines and
limitations.
6.4.1 TECHNICALSPECIFICATIONSFOR THE NON-LINEREDITING SYSTEM
A. SIGNALPROCESSING
1. Uncompressed Video:
2.
3.
4.
5.
Minimum two HD and four SD-SDI Video
streams
No. Of fields
: 2 fields per frame.
Sampling rate for video: Should be in the ratio of 4:2:2 YUVFormat
Digital Audio
: 48 kHz processing with 16-bit sampling.
Time code
: SMPTE/ EBU (LTC, VITS) with drop frame and
non-drop frame.
B. HARDWARE:
Page 14 of 42
The system should be Capable of performing all the features listed under
essential features and should adhere to the minimum configuration
recommended by the OEM. The indicative minimum configuration of the
hardware required is as given:
1. Processor
2. Operating System
3. System memory
4. System HDD
: Similar to Dual Intel Xeon 3.6 GHz processors or
higher, with 2 MB L2 cache supports 800 MHz
FSB/Two 2.4GHz Intel Xeon Quad-Core for Mac
Pro system.
: Windows XP or later/Mac OS X v10.5.6 or latter
: 8 GB or higher
: 500 GB or higher SATAHDD Dual Mirrored
: 4 TB or more having multiple HDD SATA (7200)
internal HDD (required for standalone operation)
: Two numbers of 19 inch TIT/LCD monitors with
6. Colour Monitors
resolution 1280 x 1024 Pixels, Colour resolution
of 24-Bit (16.7M Colors), response time of 20ms.
: DVD/ CD writer
7. Combo Drive
: Mouse and Keyboard, jog & shuttle controller
8. Peripherals
: NVIDIAQuadro FX 1400 or better with dual DVI
9. Graphics card
output/
ATI Radeon HD 5770 with 1GB of
GDDR5 memory, PCI Express 2.0, two Mini
Display Port outputs, and one dual-link DVI port
for Mac Pro machines
10. Firewire
: IEEE-1394a/ 1394b
11. Serial/Parallel Ports: As required.
12. Networking
: On Board 1 GB Ethernet network card that
should be able to support both 100 BaseT and 1
GB BaseT networking.
5. Media Storage
6.4.1.1 VIDEO
A. INPUT
1. Analogue components:
2.
3.
4.
5.
Y /R-Y /B-Y, 75 Q, on BNC FEMALE
(1 No each)
Analogue Composite : 75 Q, BNC FEMALE (1 No.)
,
Digital
: SD-SDI, 270 Mb/s (SMPTE 259M) and HD-SDI
1.485 Gb/s (SMPTE 292M) 0.8 Vp-p, 75 ohm, on
BNC - (1 No.)
:
0.3
Vp-p, 75 ohms on BNC. (1 No.)
Black burst
: DV input conforming to IEEE 1394b
DV/DVCPR050
B. OUTPUT
Page 15 of 42
1.
2.
3.
4.
6.4.1.2
Analogue component: Y /R-Y/B-Y, 750, BNC FEMALE (1 no. each)
Analogue Composite : 750, BNC FEMALE (1 no.)
Digital
: 0.8 Vp-p, 75 ohm (1 no.)
DV/DVCPR050
: DV output conforming to IEEE 1394b
AUDIO
A. INPUT
1. Analogue audio
2. MIC input level
3. AES/EBU inputs
: +4 dBu nom to +20 dBu max on XLR female
: -60 dBu to -30 dBu (50 Kn with +20 dBu head
room) (min. 2 nos.)
: Min Two-track.
B. OUTPUT
1.
2.
3.
4.
5.
6.
7.
Analog audio outputs: 2 Nos. at low imp (balanced) on XLR male
Analog Audio output: 2 Nos at low imp (unbalanced) (for monitoring)
AES/EBU output
: Minimum Two tracks.
Frequency response: +/ -1 dB (20 Hz to 20 kHz)
Harmonic distortion: 0.04%
SIN Ratio at 1 kHz : Better than 67 dB
Separation
: Better than 70 dB
6.5 ESSENTIAL FEATURES OF RESTORATION SOFTWARE
a. The bidder should offer restoration software for restoring various
impairments/noises
in the Video and Audio signals present in various
Tape formats. The offered restoration software should be internationally
reputed and field proven for broadcast purpose. In addition, anyone of
the reputed audio restoration softwares like Sequoia, Cedar and Cubetec should also be offered.
b. It should be capable of rectifying film originated dirt impairments like
Splotches, Scuffmarks, Unsteadiness, Noise, Scratches, Video flickers
(unwanted luminance variations), Drop out etc. The restoration software
should be able to distinguish between the wanted video motion and the
unwanted motion/unsteadiness
before restoring.
c. The offered software should be capable of detecting and removing the
impairment in the signal occurred due to momentary signal loss from
the video tape or from the signal (Video & Audio) feed.
d. The offered restoration software and the offered NLE system should
function on a common hardware platform.
Page 16 of 42
6.6 ESSENTIAL FEATURES OF 3-D GRAPHICS SYSTEM
a. General: The system should be based on a user friendly graphical user
interface. All the functions should be via this interface. The 3-D
Graphics software should be similar to Softimage XSI, 3ds max or Maya
with compositor. The system should offer the following features.
b. Modeling: The system should have highly interactive, broadcast quality
3D modeling tools such as spline modeling (NURBS based), polygonal
modeling, edge, point, curve, isoline, surface curve, boundary, sub
surface, mesh modeling etc. The system should support English and all
the major Indian regional language fonts for 3D-text creation with full
attribute control over words, lines and pages with a wide range of
colours for texts, edges, backgrounds etc. It should also be possible to
extrude and bevel text and curves.
c. Animation: The system should have full range of 3D animation and
camera & light controls in true 3D perspective. It should be capable of
animating key frame, objects, effects, and motion paths etc. It should
also be possible to synchronize animation with sound tracks.
d. Paint: The system should have paint package for creating realistic,
richly textured characters and objects. The package should have user
definable brush sizes, shapes and effects. The system should have auto
paint capabilities and real-time warp brush and paint effects. It should
also have comprehensive, pressure-sensitive
painting and drawing
tools including airbrushes, geometric shapes, and eraser. It should
have cloning and reveal controls for interactive painting between video
clips and various frames in a clip.
e. Cameras: The offered system should support multiple cameras using
industry standard camera types. It should support roll, zoom, orbit,
dolly and frame display. It should also support orthogonal projection.
f. Lights: The offered system should support various types of lights such
as point, spot, omni etc. These should be available with controls of
shadows, shadow color, density, intensity, softness etc.
g. Rendering:
The system should deliver f render broadcast quality
anti-aliased images. Therefore, it should have broadcast quality
rendering engine providing up to 16-bits color per channel with full
gamma control and able to render in frames or fields. The rendering
engine should be multi-threaded and have unlimited node networkrendering facility. The rendering engine should have advanced
rendering options like depth of field, 2Df3D motion blur, 3D volumetric
lighting, fire, explosions, smoke and fog. It should be possible to render
the different elements like shadow, reflections from the same rendering
pass.
h. Architecture: The architecture should be multi-threaded throughout for
superior performance and scalability. It should also virtually possible to
Page 17 of42
animate and edit in real time. It should support open GL and 3-D
hardware acceleration.
1. 2D/3D
Compositing: The system should include multi threaded
compositor that should be fully scriptable and it should be possible to
directly link with any 3-D scene. The software should have unified
paint, animation and 3D compo siting for broadcast graphics. It should
have multi-:processor support. The software should be capable of
compositing unlimited layers of video and images with ability to nest
composites of multiple layers inside other composites. It should offer
true 3D positioning and animation for all elements in a composite. It
should offer realistic ray-traced shadows and reflections. It should offer
multiple transfer modes including add, subtract, screen, difference,
negative and shade.
J. Effects: The system should have 2D/ 3D digital video effects. It should
also have colour correction, Chroma key and luma key facilities. The
system should have basic editing functions also.
k. Library: A library of 3-D models, environments, textures, animation,
English, Hindi, and other Indian regional language fonts (Kashmiri,
Punjabi (Gurumukhi), Assamese, Bengali, Oriya, Kannad, Tamil, Telgu,
Gujrati, Malyalam, Marathi, Urdu etc.) should be supplied.
1. Import Formats: The system should support various texture formats
such as AVI, Softimage (.pic), Targa, SGI, PCX, BMP, GIF, Alias, JPEG,
Photoshop, TIFF etc.
The system should be Capable of performing all the above listed features and
should be supplied with the followingminimum configuration.
a) Processor
: Similar to Dual Intel Xeon 3.6 GHz processors or
higher, with 2 MB L2 cache supports 800 MHz
FSB
b) Chip Set
:Inte1E7525 chipset or similar with 800 MHzFSB and
dual memory Channels or similar.
c) Operating system
:WindowsXP Professional or later
d) Memory
:8GBor more
e) Memorysize of the Graphics controller card : 512 MBGDDR3
f) System HDD
: 500 GB or higher SATAHDD
g) Storage
:Min. 2 TB SASstorage in multiple drives (7200)
h) Colormonitor
:19"TFTfLCDTrue color resolutions up to 1280x1024
i) ComboDrive
: DVD+RW
j) Networkcard
: On Board 1 GB Ethernet.
k) Graphics card
:Direct3D® 10 technology,
Direct3D 9, or
OpenGL®-capable graphics card 512 MB or
higher video card memory
Page 18 of 42
1) PointingDevice
:Certified
Tablet
with
cordless
pen
working/active area of A4 size (approx.).
m) 3 Button Optical scrollmouse & Keyboard.
6.7
of
ESSENTIAL FEATURES OF ADVANCED DIGITAL RESTORATION
SYSTEM:
a. The bidder should offer a broadcast grade Advanced high quality
Realtime Digital Restoration system similar to Snell's Archangel Ph.C for
restoration of archival material that has deteriorated due to storage and
other losses associated with old recording formats. The system should
correct all kind of video impairments & noises and enhance the restored
video signal.
b. The restoration system should be supported by powerful hardware
platform which provide comprehensive
restoration
solution by
intelligently employing advanced motion estimation and motion
compensation techniques.
c. The restoration system should be capable of automatically detecting the
impairments accurately differentiating between the artifacts/noise and
the useful element of the video signals.
d. The noise reduction part of the restoration system removes the film
grain, spatial noise, satellite salt and pepper noise, video based dropouts
occurred due to loss of magnetic coating in the video tapes, impulse
noise, random noise and electronic noises.
e. The noises should be removed by suitably applying comprehensive set of
linear filters and band limiting filters. The system should also facilitate
for removing of artifacts originated from co-related luminance and
chrominance noise.
f. The system should be capable of rectifying film originated dirt
impairments like splotches, scuffmarks, patches etc. The film and video
flickers (unwanted luminance variations), unsteadiness and picture
jerks should be removed by the system. These should be achieved by
suitably applying phase correlation motion detectors and compensators.
g. The system should facilitate interactive application of parameters and
fine tuning of the restoration process. The offered system should ensure
that the restoration process should not result in any loss of picture
resolution and quality degradation.
.
h. In addition to the restoration tools, the system should provide utilities
for picture enhancement, primary colour correction and suitable
aperture correction. This process should ensure improved quality of
video signal without introducing any overshoots/ringing in the video
signal.
Specifications for SITe of Media Asset Management
System for Archiving:
SD 01/ 20 13 dt. 01.02.13
Page 19 of 42
The system should be capable of removing the above artifacts preferably
in a single pass depending upon the nature of the error. The right
combination and the sequence should reduce the time required for the
quick and effiden t correction of the signal.
J. The offered restoration system should support HD and SD-SDI signals
with embedded audio. The time delay occurred due to the correction
process employed on the video should be calculated accurately and
should be applied on the audio signal to maintain the synchronization
between the video and audio signals.
k. The bidder should supply a dedicated PC to interface the recommended
control panel and the playback & Record VCR. The operator should be
able to analyse & optimise the restoration process and adjust the
parameters through the GUI loaded in the control PC.
1.
a. Signal Inputs
b. Reference
c. Audio
: Serial Digital 2 x 75 Ohm SD jHD Serial Digital
with embedded audio (4 Groups)
- 270M Mbitj s SD-SDI SMPTE259M
- 1.5 Gbitjs HD-SDI SMPTE292M jSMPTE299M
: 2 x loop-through HDTV TrisyncjSD Bi-sync
(Black & Burst).
: AES 8 channels unbalanced AES-3 via BNe
connectors (75 Ohm)
d. Signal Outputs
Serial Digital Primary: 2 x 75 Ohm SDjHD Serial Digital with embedded
audio (4 Groups)
- 1.5 Gbitjs HD-SDI SMPTE292M jSMPTE299M
Serial Digital Secondary: 2 x 75 Ohm SDjHD Serial Digital with
e.
f.
g.
h.
embedded audio (4 Groups)
- 1.5 Gbitj s HD-SDI SMPTE292M j SMPTE299M
: AES: 8 channels unbalanced AES-3 via BNC
Audio
connectors (75 Ohm)
Output Split Screen : H Split, H Repeat, V Split, Diagonal Split
Restoration Functions: Artefact Repair Dirt & Dust, Tramline Scratch,
Stabilization, Flicker, Video Dropout Noise &
Grain, Video Noise Reduction, Horizontal &
Vertical Enhancement
:
Embedded, AES
Audio Select
: PCM, Data
Audio Type
Specifications for SITe of Media Asset Management System for Archiving: SD 01/ 20 13 dt. 01.02.13
Page 20 of42
-
Audio Mode
Audio Gain
Audio Delay Off set
: Pass, Mute, Tone (1KHz, 4KHz)
: -6dB to +6dB (PCMonly)
: -250 to +250 ms (global)
-250 to +250 ms (per pair)
6.8 MEDIA ASSET MANAGEMENT SYSTEM:
a. The offered MAM solution should be scalable and provide integrated
content management functionality for the processes as described in the
general features.
b. It should offer real time access, edit and play rich media content for
multiple users with web enabled content database.
c. The offered MAM software should provide open interfaces for system
access and control for third party software.
d. It should provide powerful metadata management capability for
effective cataloguing, search and retrieval.
e. It should have an integrated industry standard open database
application such as SQL or Oracle or DB2 as core module. The
database should be scalable and user configurable. It should offer
standard data management tool sets.
f. It should also offer standard pre-configured internationally accepted
data models.
g. The MAMshould also be extensible for use in other areas of broadcast
workflow. The bidder should explain the complete utility of this system
in detail.
h. The transcoding applications should be faster than real-time and
should transcode to multiple formats including H.264j WM9, MPEG2
etc. at variable bit rates. The transcoding subsystem should include
powerful & robust server for continuous operation.
1. The system should provide web-based
interface to the users with
remote access capability. The software should also provide security.
J. The remote user should be able to create & modify metadata fields as
per their requirement.
k. The MAMshould be able to link the metadata, low resolution copy, full
resolution copy and full resolution file copy stored offline on a data
tape media.
1. The MAM should envisage a powerful search engine that returns
accurate results for keyword based user search with high speed. The
search could be based on keywords, name of artists and metadata or
unique ID.
m. The MAM should support file import from one defined area and export
to another defined area by using File Transfer Protocol (FTP).
Page 21 of42
n. The MAM should support creation of high resolution and low
resolution copies. The low resolution copy should be frame accurate
and time code synchronized with the high resolution content.
o. Comprehensive suite of all relevant software i.e., Ingest, metadata
creation, asset view, low res. browse & playback, intelligent search
including Boolean and refined search etc. should be offered.
p. The MAM system shall update its database as soon as the notification
for metadata updating is received from the ingest system.
q. The MAM should be capable of pulling the digitally restored media
contents available in the NLEs with software based restoration system
and from the DDRs of Advanced Digital Noise reduction and
restoration system.
r. The MAM should be of efficiently handling either the built-in or
external HSM solution for efficiently managing the LTO based Tape
Library system. The HSM not only helps in archiving the high
resolution content on data tapes but also tracks, retrieve and give back
efficiently the retrieved data to the online storage for repurposing.
s. The required number of software licenses should be offered essentially.
t. The offered MAM software should works on a stable operating system
platform like Windows, Linux etc.
u. The cost of additional licenses for Ingest, Browse I Catalogue users
etc. should be quoted separately.
I. INGESTSYSTEM:
The ingest system should be user friendly and offer the following features:
a. The ingest workstation systems should be based on standard PC
platform loaded with ingest software and required I/O card. The ingest
software should be a part of the MAM software. All ingest functions
should be via graphical user interface.
b. The MAMsystem should be capable of handling six numbers of Ingest
channels. Out of the six ingest systems, four will be for SD-SDI signal'
of two U-matic and two Betacam SP VCR sources. The remaining two
are firewire/i-link/Gigabit
Ethernet
based
sources
from two
DVCPR050 and one XDCAMHD422 VCR/Deck.
c. The base band signal will be in digital base band format. The system
should support encoding of SD base band content into MPEG-2
4:2:2@ML (I-frame only) up to 50 Mb/s and HD base band signal into
MPEG-2 4:2:2@HL (long GOP) up to 50 Mb/s. Hence, necessary
codecs to convert digital base band signal should be provided. The
codec should support DV, DVCPRO 50 and MPEG-2 formats. For
firewire/i-link/Gigabit Ethernet based ingest, native file format like
Page 22 of 42
d.
e.
f.
g.
h.
II.
XOCAM HO 4:2:2 1920xl080 50Mbps PAL should be supported. The
system should support MXF, AAF, QuickTime containerj wrapper
format for the archive content.
The offered system should also provide a Print to Tape functionality
through the firewireji-linkjGigabit
Ethernet and base band ingest
systems for export of material back to video tapej optical media (if
required). Hence these baseband ingest systems should be bidirectional.
The ingest VCR machines should be remotely controllable for the
ingest operations from their individual workstations through GUI and
relevant remote control cables.
The ingest system should communicate with the media asset
management server for the details like start, end of ingest, retrieval etc.
The play out functionality for viewing the selected high resolution
material from their respective storage should be provided in the base
band ingest systems to meet the situation when the high resolution
material should be exported to VTR.
The MAM solution should facilitate assigning any ingest workstations
which is idle to work as a browse station so that the system can be
efficiently utilised. For this, required software should be loaded in the
Ingest system and licenses, if any, required should be offered in the
quote.
QUALITYCONTROL:
a. The Quality controlling authority physically analyses the completion of
each stage of work and allows the media to move to the next stage of the
workflow. After ensuring the quality of the content to be ingest worthy,
it allows the content to get transferred from OOR or NLE storage to
online storage through ingest termin81. The QC along with Workstation
and administrative power should be provided.
b. The QC being the supervisor of the overall activities of the Archive
project, the bidder should provide a 55" LED monitor to monitor the
video signal of various stages of the workflow through a multiviewer
system.
c. The bidder should also offer powerful extemal stand-alone automated
Quality checking for file based HO and SO content. The automated
quality control analysis should be performed on ingested content as and
when opted by user. If user opts for QC analysis, the transcoding for
creation of low res content should start after certification from
administrator j QC otherwise the transcoding for creation of low res
content should start immediately after ingestion.
d. It should also be possible to integrate the QC in other stages of our
workflow also.
Page 23 of 42
e. The bidder should offer necessary hardware and software for allowing
QC of two streams simultaneously. The offered hardware should be as
certified by the OEM and be latest available in the market.
f. Offered Quality Check System should be consistent in quality check
with in-depth verification of the content.
g. Operator may easily control and configure the system as per the
requirement. User should be able to define its own template with
redefined rules for verification & quick checkup, may change the order
of streams in the queue, may define the track layout etc.
h. The reports generation should show the complete stream information
along with the visual alarms & identification.
1. QC should be able to insect the decoded base band video & audio to
evaluate its performance.
J. Quality of encoded content should also be thoroughly checked by the
system and should be able to identify errors cropped in during the
encoding process.
k. The QC system must examine the entire container structure and
metadata, the content and the codec headers, comparing the actual
contents with the expected information to identify structural problems.
1. QC should also ensure that the content has the right format
characteristics set up in the proper order.
m. The following Verification Checks should necessarily be available in the
offered QC :
Baseband Video
Baseband Audio
Encoded Content
Container
Structure
Gamut violations, Black frames, frozen frames, letter
boxes, pillar boxes, dropouts, Frame size and Frame
rate.
Audio problems such as clipping, Loudness limits, peak
limits, instantaneous peaks and true peak value limits as
well as long-term loudness over the span of the content.
Other types of baseband audio flaws including silence
due to audio dro outs etc.
Complete compliance checks
for MPEG-2 video
including compression problems like slice order errors in
trans ort stream, field order etc.
Errors such as an incorrect number of streams, e.g.,
missing audio. Incorrect Packet IDs (PIDs) for MPEG-2
Transport Streams. Errors such as a mismatch between
video and audio play duration or between actual and
signalled bit rates. Video and audio codec headers and
"unexpected" essence formats and encoding with respect
to prof1le and level, Gap structure, frame and sample
rates, picture size and aspect ratio, interlaced or
ro essive scan, color de th, and color sam 1in .
Page 24 of 42
III. TRANSCODERS:
a. The offered system should envisage required numbers of transcoding
servers that automatically transcodes the ingested DVCPRO 50,
XDCAM HD 422 or other native format contents into low resolution
formats like H.264/WM9 and MPEG2 at variable bit rates selectable by
the user at the time of ingestion.
b. The transcoding
system should be faster than real-time. The
transcoders should be designed in such a way that the low-res files are
available for viewing and metadata creation within one hour of the
ingested full resolution content in the peak load condition, i.e.,
simultaneous ingest of 1 hour clip from all ingest terminals, assuming
the time taken for QC to be zero (for the purpose of this calculation
only). The bidder should submit the calculations undertaken to achieve
this workflow for justifying the number of transcoders required.
c. During transcoding, it should be possible to extract the embedded
audio tracks into separate audio files of standard formats.
d. The transcoder should not impose limit on the size of the video clips.
e. The facility to simultaneously
extract keyframe images while
transcoding should be available on fIxed intervals of the ingested clips.
f. The MAM software should facilitate advance queue system to ensure
effective utilization of transcoders.
IV.
BROWSING,CATALOGING,SEARCHANDRETRIEVAL:
a. The bidder should offer six numbers of browsing workstations based
on standard PC platform with graphical user interface. This should
facilitate various functions like low resolution browsing, searching and
cataloguing of the contents being created or already existing in the
Online storage of the system. In case of the content backed up to the
Offline storage, appropriate location link should be generated.
b. The browser should invoke the proxy media player to view the low res.
content stored in H.264/WM9 format. The browsing software should
provide all the standard operational features of the media player like
play, pause, stop, fast forward, skip to begin/end, skip to timecode,
skip confIgurable (number of frames forward/backward), jog and
shuttle.
c. It should be possible to resize the video display area, reconfIgure the
screen layout and the activate or deactivate audio by the user.
d. Each browsing workstation should be provided with LCD/TFT monitor
and a high quality headphone to facilitate the user to listen to the
audio of the ingested content. The browsing workstation should have
at least 2 GB of high speed RAM& adequate local storage.
Specifications for SITC of Media Asset Management
SD 01/ 20 13 dt. 01.02.13
Page 25 of 42
e. The browsing software loaded in all workstations should be an integral
part of the MAM software and facilitate browsing, cataloguing, search
& retrieval applications. The offered system should support up to 30
browse users.
f. This software should facilitate creating & editing the metadata for the
ingested low resolution content. The metadata
can be quite
comprehensive and hence the software should permit the expansion of
the data structure of the database. It should have the flexibility for the
DD users to define their own metadata fields in addition to the MAM's
standard metadata database.
g. It should also be possible to import metadata and store in the offered
MAM's database after adding newly created metadata to the imported
metadata.
h. The MAMsoftware should facilitate the browser to make mark in, mark
out and capable of sequencing various clips from the ingested
contents.
1. The bidder should furnish content retrieval time from archive, along
with the bid.
V.
REMOTECONNECTIVITY:
a. The offered system should have remote access functionality. Remote
user shall able to access the low resolution content and metadata
available in the Web server through the dedicated Virtual Private
Network (VPN)for entering metadata and transcripts from the other
Doordarshan Kendras. VPN connectivity is not in the scope of this
tender.
b. It should support minimum 25 remote users.
c. The bidder should provide complete details the details of the
required software, hardware including web server, licenses, fire wall
solutions etc. to facilitate the remote access functionality, along
with the tender.
7
STORAGE SYSTEM:
7.1 Online Storage:
a. The bidder should offer on-line storage using SAS/FC drives with
available storage capacity of 30 TB after the RAID 5/6 configuration.
Out of 30 TB, 10 TB will be used for the high resolution copy and 20 TB
will be used for the low resolution copy and metadata. The storage
requirement for the system software, application software and other
management software should be provided additionally.
Page 26 of 42
-
b. The SAS/FC drives should be of Enterprise class conforming to the
latest specifications. The HDD should have very high MTBF ratings.
c. The storage subsystem should have at least four 4 Gbps host side FC
ports with native support for point-to-point, SANfabric and FC-AL.
d. The storage subsystem should have Dual active RAID controller. It
should have Controller cache of 4 GB or higher per controller.
e. The storage system should have a sustained read/write throughput of
200 MBps in the offered storage configuration. Industry/third
party
benchmarks in this regard should be provided in the literature.
f. The storage system should use hardware RAID controller and the
controller failover.
g. The storage system should be configured with 2 Global hot spare HDD
for rebuilding during drive failures.
h. The storage system should have automatic drive failure detection and
rebuilding feature.
1. All the replaceable components like Drives, Controller, Battery, Power
Supply and fan should be hot swappable.
J. The online storage should support expand ability to at least 100 TB in
future.
7.2 STORAGE/CONTENTMANAGEMENTSOFTWARE:
a. It should support Dynamic Array Expansion where new hard disk
capacity can be added to select individual RAIDarray.
b. It should support Dynamic Volume Expansion where capacity of
individual selected LUN/ volume in a RAIDarray can be expanded.
c. It should support Dynamic RAIDlevel migration, Dynamic Segment size,
Changing of a logical drive and Dynamic Defragmentation without
shutting down the system.
d. The storage management software should facilitate reallocating the
storage capacity between high resolution and low resolution depending
upon the requirement.
7.3 NEARLINESTORAGE:
a. The bidder should offer a robust, reliable nearline storage solution
essentially with open standard data tape technology like LTO 6 or
advanced.
b. The storage should have high read/write reliability with high data
throughput.
c. The bidder should offer necessary cleaning cartridges and other
accessories essentially required for the nearline storage media.
SD 01/2013 dt. 01.02.13
Page 27 of 42
d. Necessary tape management software and licenses for the same should
be offered.
e. The offered nearline storage should have at least a dual drive with
minimum 48 cartridge slots. The sustained uncompressed data transfer
rate should be 160 MBps or more. The native uncompressed cartridge
capacity should be 2.5 TB or more.
f. The bidder should offer rack mountable Tape library systems.
g. The offered storage solution should be capable of upgrading to next
generation and should be backward compatible.
h. The proposed content management system/Tape management software
should be integrated with the MAMsolution seamlessly.
1. The content
management system should support time code based
partial retrieval of the archive content.
J. The proposed content management system should be capable to
interface
with
different
reputed
tape
library
vendors
like
HP/IBM/SUN/Spectra Logic etc.
k. The system should support offline Tape Cartridge Management/
externalization of tapes for unlimited number of tapes on the shelf.
1. The content management should give performance history of all drives
and media, as well as forecast of their performance. It should be
possible to set triggers, to generate a variety of alerts when various
performance thresholds have been exceeded.
m. The content management should be controlled by Automation system.
8. HARDWARE AND NETWORK SYSTEM:
a. The system should be designed carefully to support peak load
conditions and taking into account 50% increased system load. The no.
of simultaneous user to access the content in peak load condition may
be considered as 20 users. Server and network bandwidth should not
be the performance bottleneck. The bidder should submit the
calculation undertaken & explanation, along with the bid.
b. All servers, workstations, network components and storage system
should be industry benchmarked and proven device reputed for
robustness and reliability.
c. They should meet the latest hardware technology developments and
meet high end system specifications, employing new generation
technologies.
d. The memory, bus speed and I/O performance of the hardware should
be adequately oversized to meet the increased needs in near future and
contribute towards performance improvements. This should be
elaborated.
e. The equipment level redundancies have not been envisaged (Server,
Switches, Storage array box). The component or subsystem level
Page 28 of 42
redundancies are requitred (e.g. redundant power supply, fan, RAID
controller in the storage array etc.).
f. All the necessary operating system and platform software with full
licenses should be offered in original DVD media to make the system
complete in all respect.
g. The network architecture of the system should be Gigabit Ethernet
based for Ingest & Browse terminals. The storage subsystems
including on-line storage, central storage array & data type drive
should be interconnected with servers in a fibre channel network.
h. The network is an integral part of the design The complete network
system should be designed for high quality service. The integration of
the archive system should have proven deterministic QoS.
1. The network component should have adequate buffering on channels
and should meet integrated highest quality & performance benchmark.
J. The fibre switch & necessary HBAs in the servers should be of
internationally reputed make for reliable operation.
k. The RAID controller should have high cache memory (battery backed)
for achieving rated sustained performance.
1. The bidder should offer a 1200 x 1200 dpi Black & White laser printer
similar to a latest HP LaserJet duplex network printer for printing
Metadata information.
m. The
maximum
distance
between
the
Browsing/ Cataloguing
workstations to the MAMequipment may be taken as 50 meters.
n. The bidder should provide the average latency 'max time between
request and response' for the MAM system under peak load condition
along with the bid.
8.1 TECHNICAL SPECIFICATIONS:
Hardware from internationally reputed manufactures
having service
backup throughout India, preferably in Kolkata would only be acceptable.
8.1.1 INGEST & BROWSE WORKSTATION
The hardware should have the following indicative minimum configuration.
However, the configuration should be as recommended by the OEM and be
the latest available in the market.
a) Processor
: Intel Xeon X3450, 2.67 GHz, 8 MB Cache or
better
Page 29 of 42
b) Chipset
c) Operating system
d) Memory
e) System HDD
1) Colour monitor
g) Storage Controller
h) Combo Drive
i) Accessories
j) Network
k) Graphic card
1) Interfaces
m) Power Supply
8.1.2
: Intel 955X with 800 MHz FSB or higher
:Windows
7
downgrade
to
Windows
XP
Professional (with latest Service Packs from
Microsoft) / Linux or better .
: 4 GB or higher, 1066 MHz; expandable up to 16
GB
: 500 GB or higher Serial ATA7200 rpm.
: Wide Aspect ratio, 19" TFT Display supporting
resolution of 1920x1200
: Integrated 4 Channel Storage Controller
: 16X DVD Writer
: High Quality Head phone, Sound card, Optical
Scroll Mouse, 104 Keys- Key Board
: Integrated 10/100/1000 Ethernet Port
: NVIDIAFx 380 or as recommended by the OEM
offering MAM.
: 1 Parallel, IEEE 1394 (for Ingest Systems), 6
USBs, 2 Serial, 2 Ultra ATA/100 2 PS/2 for
mouse and Key board, 1 Video, 1 Microphone and
Head phone each, Line In and out jack and 1 RJ45.
: 230V AC ±5 %, 50 Hz
RACK SERVERS
The hardware for rack mounted servers should have the following
indicative minimum configuration. However, the configuration should be as
recommended by the OEM and be the latest available in the market.
a) Processor
b) Chipset
c) RAM
d) No. of DIMM slots
e) Hard disk
1) Graphics
g) Network Adapter
h) Raid Controllers
i) PCI Slots
: Two numbers of Intel Xeon X5560, 2.8 GHz,
8MB Cache, 6.40 GT/s QPI, Turbo, HT
: Intel 5520 Chipset
: 16 GB
: 12
: 2 x 146 GB, 15K SAS, hot plug HDD
: Integrated graphics 8-MB video Memory
: Two dual port embedded Gigabit Ethernet NIC
with failover and load balancing. Should support
TOE, iSCSI, RDMA, Wake-an-LAN (WaLl, PXE
2.0 remote boot
: Configured with RAID 5. Should support RAID
level 0,1,5,6,10,50,60 with 256 write back and
write through battery backed cache.
: Four PCI Express
SD 01/ 20 13 dt. 01.02.13
Page 30 of42
j) I/O Slots
: Two x8 Gen2 slots
k) Optical Drive
: DVD ± RW Drive
1) Networking Protocols: IPv4 & IPv6 should be supported
m) Auto Diagnostic features
: Predictive failure warning on processor,
memory, Hard disk, power supply and fan
n) Power
: 2 hot plug Redundant
power supply and
redundant cooling fans.
0) Rack Support
: 19" Industry Standard Rack Ready
p) Operating System Support: Microsoft, Redhat and Sue Linux. Offered
model should support all latest version of
Microsoft Windows, Redhat and Sues Linux.
q) System Management
OEM Management software should allow to
manage
system with proactive monitoring,
diagnosis, notification, and remote access. It
should provide the features like Security
management,
A command
line interface,
Extensive logging, Ability to review and report
the configuration and status of a host-based
RAID subsystem, Update capability for BIOS
and firmware for server, Diagnostic tools to
isolate hardware problems while the system is
still operational Rapid access to detailed fault
and performance information that is reported
in the user interface. Remote administration of
monitored systems, including BIOS setup,
shutdown,
start up, and remote access
controller (RAC) security, Remote access to an
in operable
system,
allowing to obtain
complete control of the local console.
8.1.3
ON LINE STORAGE SYSTEM:
a)
b)
c)
d)
e)
i)
Size of Online storage
: 30 Terra Bytes, FC interface
Storage for low-res content: 20 Terra Bytes of SAS/FC HDD
Storage for high-res content: 10 Terra Bytes of SAS/FC HDD
Cache memory
: 4 GB per controller
Global Hot Spare of HDD : 2 Nos.
HDD
: 10000/15000
rpm, complying with latest
SAS/FC specs for enterprise application.
g) Sustained throughput
: at least 200 MBps (Read & Write)
h) RAIDController
Hardware RAID controller with
ASIC
Supports all RAIDlevels
i) Number of host ports
: minimum 4 x 4 Gbps host ports
Page 31 of 42
8.1.4
a)
b)
c)
d)
NEARLINE STORAGESYSTEM:
Number of drives
: at least 2 drives in the same chassis
Number of cartridges slots : minimum 48 Nos.
Capacity per cartridge
: 2.5 TB native or higher
Sustained Data transfer rate
: 160 MBps native per drive or better
9. ASSOCIATED PERIPHERAL EQUIPMENT:
(a) 17" LCD monitors having 1280X768 native resolutions with high
Horizontal and Vertical viewing angle for clear viewing should be
offered. All the offered monitors should have dual inputs i.e., HD/SDSDI and analog input. Audio output should be available on Mini
jack/RCA and monitor should have built-in speaker.
(b) Genlockable dual SPG with auto change over facility should be offered
along with the system. Both the main and back-up units should have
HD Tri-Ievel, Bi- Polar Synch, Analog Black Burst (PAL).
(c)The offered amplispeaker should have excellent performance features
like "flat frequency response", "carefully controlled roll off', and "very
low distortion".
(d) HDjSD-SDI Waveform Monitor should be offered and installed in the
rack for monitoring purpose. Offered monitors should have dual inputs
and facilityfor eye pattem and jitter display.
10.
TECHNICAL FURNITURE & INSTALLATION MATERIALS:
a) Suitable technical furniture including operators chairs etc. required for
the facility will be part of the offer.
b) The offered technical furniture should be designed for modularity,
ergonomics and high end aesthetics.
c) The front and rear device tracks of the furniture should allow lateral
positioning of critical monitors.
d) The rack bay turrets may be easily upgradable or re-Iocatable allowing
quick and user friendly modifications.
e) A full range of articulating arms for distance, height and tilt control
may be provided for mounting flat panel monitors, speakers, phones
etc.
f) The offered technical furniture should have integral cable management,
removable vented abs panels and movable & interchangeable rack
turrets.
g) All furniture should be made of high quality material. The power supply
distribution panels should also be integrated with these desks.
Page 32 of 42
h) All sorts of installation materials including Audio and Video rack to
house storage, server etc., all sorts of connectors & cables etc. are
required to be offered along with the bid.
11.
SOFTWARE:
The software of the all the equipment including Operating
Systems and automation & application software etc. are
required to be supplied in original media and should be
licensed to Doordarshan with perpetual validity.
The bidder has to provide software support/up
free of cost during the warranty period.
gradation
A certificate to this effect is also required to be submitted
bv the bidder. alone: with the bid.
12.
COMPLIANCE:
(a) The bidder must submit point by point compliance statement
in
respect of all the points laid down in this specification for all the
equipmentl item(s) alongwith the bid by the bidder in the below
mentioned proforma.
In case the bidder does not have requisite experience and
enters into an MoU with a partner, the point by point compliance
statement
in respect of all the points laid down in the
specifications for all the equipmentl item(s) shall be duly signed by
the bidder as well as his partner.
(b) In addition to above, a separate point-by-point
full compliance
statement
and authorization from the respective
principal
manufacturers in respect of the equipment listed below should
necessarily be submitted.
(i) Media Asset Management System including hardware, storage,
HSM, QC etc.,
(ii)
Standard Noise Reducers
(iii) Analog to Digital convertor cum audio Embedder
(iv)
(v)
Router System
(vi)
Software based Restoration on NLE Systems including hardware
(vii) NLE with 3D System including hardware
(viii) Precision Air Conditioning System
(ix)
UPS System
Page 33 of42
All the parameters related to the concerned equipment/ item(s)
laid down in this specifications from the respective principal
manufacturers is to be enclosed along with the offer in the format
given below. Mere signature on the copy of DD specifications shall
not be accepted as a compliance statement.
The figures so mentioned should be supported by record of these
in the technical literature enclosed with the tender and reference
to the page number of enclosed literature for all features and
technical specifications should be mentioned in the relevant
column. Offers without the compliance statement or incomplete
compliance statement
will liable to be rejected with the sole
responsibility of the bidder. Any deviation from the specification
detailed in the compliance statement
is to be highlighted
separately.
Cl
Cl
•....
rJ'J
o ui
Z ()
0..
()
l1)
o
8..
I-t
00
rJ'J
1.
13.
rJ'J
Cl
Cl
2.
4.
8.
6.
5.
TECHNICAL LITERATURE:
One set of printed technical and operation & maintenance manuals for all the
equipment are to be provided on non-returnable basis along with the tender
to facilitate the technical evaluation, otherwise the tender is liable to be
ignored. The successful bidder will have to supply two sets of printed
operation, service and maintenance manuals with respect to each equipment.
14.
DEMONSTRATION/PRESENTATION:
If necessary, the bidder may be asked for demonstration/presentation
of the
offered system as part of the technical evaluation. In such case the bidder
will have to make suitable arrangement for the demonstration/presentation
of the offered system at Doordarshan Bhawan, New Delhi, on notice of 15
days.
Accordingly
the
bidder
should
be
in
readiness
for
demonstration/presentation
on a notice of 15 days.
SD 01/2013
dt. 01.02.13
Page 34 of 42
15.
GUARANTEE:
(a) With reference to the clause no.8.2 of the "General Terms And
Conditions
(GTC)" under ANNEXURE-II of tender document,
the
complete system including all items/ equipment should be guaranteed
for two years of trouble
free operation
from the date
of
commissioning.
In case of any item or equipment failure including
software and hardware within this period, the same shall be rectified
or replaced free of cost to Doordarshan at the site. In case, it is not
rectified within one week, replacement
of the equipment shall be
arranged by the bidder.
(b)The guarantee
includes
all hardware,
software and modules of
complete system.
(c) The bidder will provide up gradation of all the offered software free of
charge during the warranty period. The bidder will be reauired to
e:iveundertakine: to this effect. alone:with the bid.
16.
ON-SITE TRAINING:
The system envisaged is sophisticated and requires training for operation
and maintenance. The bidder has to offer trainings as given below:
(i) Operators Training: The bidder should
offer Operators Training to ten
persons for duration of 1 week at the installation site immediately after
completion of installation and before handing over of the system.
(ii) Administration and System Support Training: The bidder should offer
Administrative and System Support Training on System Architecture,
System configuration, Maintenance & Hardware support to a core team
of five members for duration of 2 weeks at the installation site
immediately after completion of installation and before handing over of
the system.
(iii)Managers Training: The bidder should offer introductory
training for the
senior officers of Doordarshan for a duration of 2 days at the installation
site after completion of installation and before handing over of the
system.
(iv)Follow-up Advanced Training:
The bidder should offer Follow-up
Advanced Training for five working days at site after two months of the
training mentioned at (i) and (ii)above.
SD 01/ 20 13 dt. 01.02.13
Page 35 of 42
Accordingly, necessary resource persons are required to be deputed for
imparting the trainings. The bidder has to provide the comprehensive
training material in the form of hard copies, as well as soft copies to the
trainees, during the training session. The complete cost towards these
trainings and operational support, if any, should be quoted separately.
17.
INSPECTION:
The equipment shall be subjected to inspection by Doordarshan officials.
18.
DELIVERY PERIOD:
The delivery period for completion of SITC is 5 months from the date of
placement of purchase order.
19. ENCLOSURES:
The bidder must necessarily submit the following enclosures along with the
technical bid:
(a) Compliance statement
with respect to all the points of the
specifications duly signed by the OEM should be submitted. The
reference to the page number of enclosed literature for all features and
technical specifications should be essentially mentioned in the relevant
column of the compliance statement.
(b) A separate point by point compliance statement duly signed by the
bidder or bidders as well as the partner, as applicable, in respect of all
the points laid down in the specifications for all the equipment/item(s)
in the proforma mentioned in clause no. 12(b).
(c) Certificate as required vide clause no. 11.
(d) An undertaking as required vide clause 15(c).
(e) Detailed Video and Audio schematics including block diagrams and
work flow.
(f)
Layout
of the facility depicting ingest desk, Browsing desk &
Restoration desk, monitoring wall, engineering desk etc.
(g) Power supply load calculation sheet. Power supply schematic with the
layout of power switchgears, PDP etc.
(h) Air-conditioning details including heat load calculation and system
design.
(i) Technical manuals/Detailed technical literature/catalogues
for all the
offered products for substantiating
the model no: and technical
specification.
Product/Model specific User list of the offered product.
m
SD 01/2013 dt. 01.02.13
Page 36 of 42
(k) Work experience with details, supporting documents and client details.
(1) Any other document mentioned elsewhere in the tender document.
The tender is liable to be rejected in the absence of the above
enclosures with the sole responsibility of the bidder.
***************************************
Page 37 of 42
Aooendix-:.!
INDICATIVE BILL OF MATERIAL (BOM)
81.
No.
1.
(a)
Components
Media Asset Management System Compnsing of :
MAM application suite with database & all
1 Set
required functional modules
{b} Transcoders
(c) Ingest system (2 Nos with firewirefiLinkf Gigabit Ethernet and 4Nos with
Bi-directional
baseband video ingest)
(d) Browsing & cataloguing terminals (6
Desktop) with individual UPS for
Desktop
{e} Workstation for Administration with UPS
(1)
Application, Storage, Browse, Database,
HSM Servers etc.
(g) Networking Components for FC & Gigabit
Ethemet including HBAs.
(h) Online storage of 30 TB with Storage
Management Software including necessary
housing.
(i) Near Line Storage -Data Tape Library
(minimum 48 slots)
Data Tape Cartridges
(k) Black & White Laser jet network printer
m
(1)
2.
(a)
(b)
(c)
3.
4.
5.'
Quantity
Analog to Digital Converter with Audio
Embedder Mounted in Rack frame
Time Base Corrector
Specifications for SITe of Media
Asset
Dalet, Harris, Vizrt
(Ardome), Masstech
(Indigo)
1 Lot
6 Nos
-
6 Nos.
HP, IBM, Dell
1 No.
1 Set
HP, IBM, Dell
HP, IBM, Dell
1 Set
-
1 Set
Netapp, HP (MSA),
Editshare, Dell
(EqualLogic)
HP, IBM, Dell, Spectra
Logic
IBM, HP, Dell
HP
1 Set
50 Nos.
1 No
32 X 32 HD / SD-SDI Router (AVe) with
1 Set
redundant power supply and RCP :
(i)
Single Bus - ION os
Iii} XY Bus - 1 No
High Quality Real Time Digital Restoration System
1 No.
Digital Disk Recorder (l-ch REC & l-ch
PLAY)
PC with accessories to interface the
control panel and the playback &
Recorder
Standard Noise reducer mounted in rack
frame with redundant power supply
Products similar to
1 No.
1 No.
5 Nos.
4 Nos.
3 Nos
HP, IBM, Dell
Harris, Probel, Evertz ,
Grassvalley, Utah
Scientific, Miranda
Snell (Archangel Ph.C
-HD)
Doremi (MCS Server),
Grassvalley {T2iDDR}
HP, IBM, Dell
Snell, Ensemble,
Grassvalley, Evertz,
Harris
Snell, ROSS,
Grassvallev, Vistek
FORA, Snell
Management System for Archiving: SD 01/2013 dt. 01.02.13
Page 38 of 42
81.
No.
6.
7.
(a)
Components
Quantity
Gen lockable dual SPG with Auto change
1 No
over unit
Software based Restoration System with NLEs
NLE with Video restoration Software and
1 No.
UPS
(b)
NLE with Audio restoration
UPS
8.
11.
NLE system with 3D Graphics including
pointing device for DVDI Blu ray
authoring with UPS
Automated QC for File based ContentHardware and software with 2 nos licences
Ampli-speakers for audio monitoring at
various desk
17" HD 1SD-SDI Video Monitors
12.
55" LED Monitor
1 No
13.
16 channel MultiViewer
1 No
14.
HD/SD-SDI Waveform Monitor (with dual
inputs and facility for eye pattem and
jitter display)
40 KVA 3 phase input and 3 phase output
online UPS system in (1+ 1) mode with 30
min backup
Air conditioning System :
Precision Unit
Power Distribution Panel
Power, Audio, Video & data Cables and
other installation materials
Installation materials, HD Patch Panels,
patch cords, Racks, Consoles etc.
On-site Training - as specified In the
Specifications clause no. 16.
9.
10.
15.
16.
17.
18.
19.
20.
Software and
1 No.
1 No.
1 Lot
9 Nos
20 Nos.
2 Nos
1 Set
1 lot
Products similar to
Tektronix, Trilogy,
Harris, Evertz
Grassvalley (EDIUS),
Apple (FCP), Matrox
(AdobeCS6), Harris
(VelocityHD),Avid
with HS-Art (Diamant),
MTIFilms (Correct DRS),
Red Giant (Film Fix)
Grassvalley (EDIUS),
Apple (FCP), Matrox
(AdobeCS5), Harris
(VelocityHD),Avid
with audio-restoration
software.
Autodesk 3DsMax,
Softimage, Maya
Cerify- Tektronix,
Baton- Interra
. Genelac, JBL
Sony, Kroma, JVC,
Panasonic, Plura
Samsung, LG,
Panasonic
Harris, Evertz,
Miranda
Tektronix (WFM
7120/7200), Leader
(LV 5800)
Similar to Eaton, APC,
Piller and Emerson
Emerson, Stulz
1 Set
1 Lot
1 Lot
1 Job
Page 39 of 42
SI.
No.
21.
22.
23.
24.
Components
The software of the all the equipment
and
Systems
Operating
including
etc.
software
application
automation &
are required to be su pplied in original
to
be licensed
should
and
media
Doordarshan with perpetual validity.
Technical Furniture :
Sturdy, modular and ergonomically
designed Technical furniture for
a. Ingest Desk,
b. Browsing Desks
c. Restoration Desks
d. Editing Desks
e. Administrator/Quality Control
Desk
Anv other furniture required.
Operation & Maintenance Manuals (Hard
copy & soft copy) of each & every
equipment
Any other item(s)/ equipment/installation
material/ works required for completion of
the work on SITC basis to make the
system fully functional in all resoect.
Quantity
Products similar to
1 Lot
1 Lot
2 Sets
SD 01/ 20 13 dt. 01.02.13
Page 40 of 42
)
Appendix-II
stem at Doordarshan Kolkata
DVCPR050
VCRs/Decks will
be provided by
Doordarshan
~,
;"~
XDCAM
ADVANCED DIGITAL
RESTORATION SYSTEM
QUALITY CONTROl
MAM
PROPOSED
BROWSE
& METADATACREATIONSYSTEM
(6 Nos)
MAM
SYSTEM FOR
ARCHIVING
Specificationsfor SITe of Media Asset Management System for Archiving: SD 01/2013 dt. 01.02.13
Page 41 of 42
Appendix - III
Layout showing dimension of the Rooms at Doordarshan, Kolkata
Location : Second Channel
Building,
./
Second Floor
AI partition
(can be removed/shifted
, if required)
!/
!
A
c
I0
I 0
.
'p
Door
9_00r
D
Toilet
Door
G
Door
Door
r--
[
'
F
Toilet
-
"I
Corridor width 1.87 Mts, Floor Height 3.25 Mts
I.
-
l
Door
Door
Door
E
B
Not to scale
(I) ROOM A, B,C & D CAN BE USED FOR INSTALLING THE FACILITY UNDER
THIS TENDER.
(II) ROOM E, F & G SHALL BE USED BY DOORDARSHAN
FOR ADDITIONAL
FACILITY.
Room
Breadth
Length
Area (M X M)
33.3125
A
6.25
5.33
B
9.63
5.1
49.113
C
3.38
5.33
18.0154
0
2.93
5.33
15.6169
E
2.93
5.1
14.943
F
6.06
5.33
32.2998
G
3.13
5.33
16.6829
TOTAL AREA (Sq. Mts)
179.9835
SD 01/ 20 13 dt. 01.02.13
Page 42 of 42

Specification

Transcription

Similar documents

Turning the - Incriminator Audio

Every Day Counts in Improving Mobility: A l d B id C i Every Day

your report here

10020A Pendleton - Standard Furniture

40 Acres of Butler County Native Grass

Katalóg karta AV-2500-ECO

Students use AutoSketch software to complete the design of a home

vTuner Internet Radio Rapid Prototyping SDK USB

Bticino 334202 (5 Wire)

COMMERCIAL: Link Media - Everest Lounge, Harrow, UK