Techstar Dock Catalogue - thomasnet

www.techstarplastics.com
Commercial and Residential
Dockfloats
Techstar Dockfloats keep all of your lumber out of the water!
Single Source for Dock Floats, Hardware, Ladders & Accessories
www.techstarplastics.com
5 STEP DOCK STAIRS
4 STEP DOCK LADDER
DOCK BUMPERS
DL-5
EVERYONE’S
FAVOURITE
• Dog Friendly
• Flip up for Winter
• Extra Wide Non-Slip
Stairs
• Vertical distance
from the top of
your dock to the
VIDEO
bottom of your
ONLINE
stairs - 55”
DOCK CARTS
DL-4
• Flip up for Winter
• Non-Slip Textured
Steps
• Vertical distance
from the top of
your dock to the
bottom of your
stairs - 45”
DOCK ANCHOR
BB-7 47.5” x 7” x 2.5”
BB-9 47.5” x 9” x 3”
HOT DIPPED GALVANIZED
DOCK HARDWARE
HARDWARE
2X6 FRAMES
CB5 Corner Bracket
H5 Hinge
BP5 Backing plate
I/O - 20
Overall Dimension
63”L x 31.5”W x 27”H
KAYAK/SUP RACK
Model Number R-1
VIDEO
ONLINE
AF-250
24” diameter x 10” high
Weighs 250lbs when
filled with concrete.
HARDWARE
2X8 FRAMES
CB7 Corner bracket
H7 Hinge
BP7 Backing plate
ANCB-7 1/4” thick anchor
corner bracket for
any frame
2 TECHSTAR DOCKFLOATS KEEP ALL OF YOUR LUMBER OUT OF THE WATER!
BUMPER FLOATS
Techstar Bumper Floats are a unique combination of dock bumper and flotation.
Designed to run the length of your dock on both sides, these floats will comfortably float a dock 8 feet wide. For docks 10 to 12 feet wide we recommend one row of
centrefloats and for docks 14 to 16 feet wide we recommend 2 rows of centrefloats.
Features and Benefits
• Dock Bumpers are built in as part of the float.
• Foam filled with closed cell EPS (expanded polystyrene)
for added security.
Patent Pending
• Your wood frame, hardware and decking stay out of the water.
• Polyethylene is environmentally friendly, as well as gasoline
and wildlife resistant.
• Construction is simple. Build a frame with corner
brackets and attach floats through molded bolt holes.
• Deck boards can sit flush with the top of the floats for
a clean finish.
• Standard colour is black but Bumper Floats are also
available in sandstone at an extra cost.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness Shipping Weight Center Float Model Per Skid
BF-1
24” x 48” x 16”
415
.187
43lbs
AP-8
12
BF-12
24” x 48” x 21”
430
.187
43lbs
AP-12
12
BF-3
24” x 48” x 25”
700
.250
65lbs
MF-2448
8
Techstar BF-2 Bumperfloats make the narrowest
Bumperfloat dock with the maximum stability.
4 Foot lengths allow you to build a 4.5 Foot wide
dock in lengths of 8 feet, 12 feet, 16 feet etc.
Patent Pending
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness Shipping Weight Center Float Model Per Skid
BF-2
54” x 48” x 16”
990
.225
80lbs
www.techstarplastics.com
Not Applicable
6
3
HEAVY DUTY
SHOULDER FLOATS
Techstar Heavy Duty Shoulder Floats are
commonly used in large commercial docks. Perfect for marinas, two size floats accommodate
finger docks 24”, 30”, 36” and 48” wide.
Features and Benefits
• You can comfortably use large framing such as 2x12 or 3x10.
• Model MF-3036 has 8 molded holes for ease of attachment.
• Model MF-2448 has 12 molded holes.
• Adjustable dock height with different frame heights.
• Our toughest floats - 3/8” thick.
• Molded cable trough.
Requirements:
A minimum of one HD Shoulder Float is required for every 25 square feet of deck surface you are building. If you are building a dock 60’x10’ or 600 square feet, you would need 24 floats minimum (600 divided by 25 = 24) to float your dock
properly. If you are hinging 30”x20’ finger docks to this main dock, each finger would be 2.5 x 20 = 50 square feet. You
would need a minimum of 2 Model MF-3036 floats for each finger, one mounted about a foot from the deep end and one
in the middle. The main dock should float the hinged end adequately.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness
Sq. Foot Deck
Coverage
Shipping Weight
Per Skid
MF-3036
30” x 36” x 22”
575
.375
25
65lbs
4
MF-2448
24” x 48” x 22”
630
.375
25
70lbs
8
LOW PROFILE
SHOULDER FLOATS
The Techstar Low Profile Shoulder Float is uniquely
molded with a mounting shoulder and holes to
bolt through to your frame. They are ideal for all
applications including commercial docks and
large residential docks.
Features and Benefits
• Low Profile Shoulder Float allows you to use any size framing lumber 2x6 or larger.
and bolt sideways through a choice of 8 molded holes.
• Now foam filled for added security.
• 12” of flotation sits under your frame
• Many dock builders find this float the easiest to build with.
Requirements:
A minimum of one LP-2448 is required for every 20 square feet of deck surface of the dock you are building. If your dock
is going to be 30’x12’ or 360 square feet, you would need 18 floats minimum (360 divided by 20 = 18) to float your dock
properly. 4 Floats should be set in the corners and the balance spread evenly throughout the surface area.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness
LP-2448
24” x 48” x 16”
425
.250
Sq. Foot Deck
Coverage
Shipping Weight
Per Skid
20
48lbs
10
4 TECHSTAR DOCKFLOATS KEEP ALL OF YOUR LUMBER OUT OF THE WATER!
ALL PURPOSE FLOATS
Techstar All Purpose Dock Floats offer the maximum in design flexibility and economy.
Each float has 6 molded holes enabling you to lag your floats to your frame up from the bottom.
You can use any size framing lumber 2x6 or larger. 3 Different heights allow you to choose your
freeboard.
Why choose Techstar All Purpose Dock Floats?
1. Both lumber and hardware stay out of the water, floats
lag through moulded holes to the bottom of your frame.
2. Less wood required for construction.
3. Less labour to build your dock.
4. Polyethylene is environmentally friendly.
5. Polyethylene is gasoline resistant.
6. Polyethylene is resistant to aquatic wildlife such as muskrats, otters and beavers.
7. 3 Heights to choose from (8”, 12” and 16”).
8. 6 Mounting holes are molded in.
9. All 3 sizes are filled with closed cell expanded polystyrene.
Requirements:
Choose your required freeboard then pick the correct float for height taking into consideration your
frame height. Next, work out the square footage of your dock design and consult the chart below. Let’s
say you were going to build an 8’x20’ standard rectangular dock and wanted to use AP-12 floats. Your
dock would be 160 square feet so if you divide by 20 (the number off the chart), you would need a
minimum of 8 floats. Put a float close to or right on each corner and spread the balance out relatively
equally. An extra long or heavy ramp will require flotation where dock and ramp meet.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness
Sq. Foot Deck
Coverage
Shipping Weight
Per Skid
AP-8
24” x 48” x 8”
250
.125
15
28lbs
20
AP-12
24” x 48” x 12”
400
.150
20
35lbs
12
AP-16
24” x 48” x 16”
510
.225
25
45lbs
10
www.techstarplastics.com
5
WATERCRAFT FLOAT
Imagine a Drive On Roll Off float that blends
in with your wooden dock. The Techstar Model PWC-1 does exactly that. Techstar supplies
the float complete with 4 polyurethane rollers
and you build the frame to suit your machine
and deck it with the same wood as your dock.
Model PWC-1 allows easy drive on and roll off with your watercraft. Ideal for small boats, you can also pull an aluminum up to stay dry
while you are away from your cottage.
The sloped interior and recessed polyurethane rollers mean your PWC always sits in the center.
Specifications
VIDEO
ONLINE
FRAME FOR PWC
Overall dimensions - 81” Wide x 74” Long x 24” High
Inside width with Bumpers - 54”
Inside width without Bumpers - 59”
Shipping weight - 160 Pounds
Flotation - 1600 pounds
Polyurethane rollers on stainless steel axles and hardware.
FRAME FOR
ALUMINUM BOAT
Construction - for Watercraft
Build your frame to suit the size of your machine, then center the float under your machine. Leave some room to move the
float forward or backward to fine tune the drive on, roll off feature. Techstar Bumperboys protect your dock and PWC.
Construction - for Aluminum Boat
Build your frame to the size of your boat and place the float near the back.
We do not recommend driving an aluminum onto the ramp, rather you should pull it up by hand or winch.
RAFT FLOAT
4 Techstar Raft Floats makes a perfect 8 x 8
swim raft which is sure to keep kids busy for
hours. Molded in beautiful sandstone, this float
matches perfectly with Techstar’s ladder and
dock stairs. A simple 2 x 6 frame requires no
corner brackets as it bolts right thru the floats.
There is however a molded hole to attach an
anchor bracket through to your frame.
Features and Benefits
• Dock bumpers are built in as part of the float.
• Foam filled with closed cell EPS (expanded polystyrene) for added security.
• Your wood frame, hardware and decking stay out of the water.
• Polyethylene is environmentally friendly, as well as gasoline and wildlife resistant.
• Construction is simple. Build a frame without corner brackets and attach floats through molded bolt holes.
• Build with a 2 x 6 frame and 2 x 6 deck boards can recess in the top of the floats for a clean finish.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness Shipping Weight
RF-1
48”x48”x15.5”
300
.187
48lbs
Per Skid
6
6 TECHSTAR DOCKFLOATS KEEP ALL OF YOUR LUMBER OUT OF THE WATER!
WHEEL FLOAT
Techstar’s Wheel Float (patent pending)
enables you to remove your dock effortlessly.
Just roll it right out of the water on to the shore!
Features and Benefits
• Both 23” wheel and float are foam filled with EPS (closed cell expanded polystyrene.)
• 750 Pound rolling capacity, 575 Pound flotation.
• Heavy duty 1 7/8” aluminum axle
•Wheel is built right into the float
VIDEO
• Easy to assemble - 6 mounting holes
ONLINE
• Compatible with both wood and aluminum docks
• Float Dimensions 24” x 48” x 18” c/w wheel overall 24” x 48” x 28”
• Shipping weight 72 lbs
Prolong the life of your dock against ice jams and winter damage. This innovative design is perfect for dock
builders that offer spring launching and fall removal services.
Model Number
WF-18
Wheel Diameter/ Outside Dimensions
Load Capacity
(incl. wheel)
23 / 750
24”x48”x28”
Flotation (pounds) Average Wall Thickness Shipping Weight
575
.187
72lbs
Per Skid
4
SKID PLATE FLOAT
Techstar’s Skid Plate Floats are heavy duty
floats with mounting holes top and bottom.
Features and Benefits
• Molded holes on the bottom of the floats accommodate attachment of skid plates to the bottom of your dock.
• Molded slots and holes around the floats give you maximum construction flexibility.
• 5 Sizes to choose from.
• Foam filled for added security.
• Skid Plate Floats are a favorite with dock builders that offer spring
and fall services for launching and taking out docks annually.
SKID PLATE
• Skid Plate Floats make great finger docks too.
Requirements:
The chart below shows the square foot coverage for each Skid Plate Float.
If you are building a dock 9’x20’ (180 square feet) you could use 6 x SP-3648.
Model Number Outside Dimensions Flotation (pounds) Average Wall Thickness
Sq. Foot Deck
Coverage
Shipping Weight Per Skid
SP-2448
24” x 48” x 12”
400
.187
20
35lbs
12
SP-3648
36” x 48” x 12”
600
.187
30
45lbs
6
SP-364816 36” x 48” x 16”
800
.187
40
55lbs
6
SP-4848
48” x 48” x 12”
800
.187
40
55lbs
6
SP-3672
36” x 72” x 12”
900
.187
45
70lbs
6
SP-4872
48” x 72” x 12”
1200
.187
60
90lbs
6
www.techstarplastics.com
7
Techstar Plastics Inc.
15400 Old Simcoe Road,
Port Perry, On, Canada L9L 1L8
Port Perry: 905-985-8479
Toll Free: 1-800-263-7943
Fax: 905-985-0265
E-Mail: [email protected]
TECHSTAR DOCKFLOATS KEEP ALL OF YOUR LUMBER OUT OF THE WATER!
TECHSTAR DOCKFLOATS KEEP ALL OF YOUR LUMBER OUT OF THE WATER!