ALPHAFLOW® Alphaflow - in

Transcription

ALPHAFLOW® Alphaflow - in
CRÉATIONS COULEURS®
ALPHAFLOW®
Alphaflow®
Moisturizing CC Cream with Alphaflow®
Moisturizing CC cream is designed to
hide small imperfections and bring
brightness and smoothness to the skin
as well as provide fresh and light
texture. Hydrasoft® Moist provides
viscosity to the formulation and brings
moisture to the skin. Biomethics® is fully
natural emulsifier with good skin
compatibility and does not disrupt skins
barrier as traditional emulsifiers do.
Alphaflow® 20 is an ultra pure
hypoallergenic emollient for even most
delicate skin. It is non-comedogenic,
extremely safe, but totally inert and
hydrates the skin without affecting skin
barrier. Meadowfoam Seed Oil is an
extremely stable vegetable oil that
gives good skin care benefits. Creasil®
11 ID is a film former and designed for
long
lasting
colour
applications.
Talcpoly® is a filler that leaves a soft
finish to application. Creasperse® UV
products are predispersed mineral UVfilters
based
on
photostable
Alphaflow®.
Formula Reference PFI 489CUV
Ingredients
INCI Name
Qty%
Supplier
Phase A
Hydrasoft® Moist
Biomethics® Solanum O/W
Phase B
Alphaflow® 20
Creasil® 11 ID
Creagel® Crystal
Phase C
Talcpoly® WL 4
Water
q.s.
Propylene Glycol
2,90
Glyceryl Stearate (and) PEG-100 Stearate
0,40
Chlorophenesine
0,20
Disodium EDTA
0,05
Glyceryl Polymethacrylate (and) Propylene Glycol
19,20
Solanum Tuberosum (Potato) Starch (and) Water (and) Helianthus
4,80
Annuus (Sunflower) Seed Oil (and) Sucrose Stearate (and)
Xanthan Gum (and) Hydrogenated Lecithin (and) *preservative system
1)
1)
Hydrogenated Polyisobutene
2,00
Isododecocane (and) Dimethicone (and) Polyethacrylate
1,50
C12 - 15 Alkyl Benzoate (and) Ethylene/Propylene Copolymer (and)
Octyl Methoxycinnamate (and) Butyl Methoxydibenzoylmethane 12,00
1)
1)
Talc
1,20
1)
Perfume
Titanium Dioxide (and) Hydrogenated Polydecene (and)
Triethoxycaprylysilane (and) Hydroxystearic Acid (and)
Alumina
Titanium Dioxide (and) Hydrogenated Polydecene (and)
Hydroxystearic Acid (and) Triethoxycaprylysilane (and) Alumina
(and) Disteardimonium Hectorite (and) CI77491 (and) CI77499
0,01
5,00
1)
12,00
1)
1)
Phase D
Creasperse® TR 45 AF 75
Creasperse® CC AF
* Preservative systems is tailor made upon customer’s request
Procedure:
1. Heat up phase A to temperature of 75-80°C and keep under agitation until homogeneous.
2. Heat up phase B to temperature of 75-80°C and keep under agitation until homogeneous.
3. Add phase B into phase A and homogenize (8000- 10000rpm) for 5 minutes. Let it cool down to temperature below 35°C under
low agitation.
4. Adjust pH around 5,5.
5. Add phase C then D into (A+B) and keep under agitation until homogeneous.
6. Homogenize (1000 rpm) for approximately 1 minute, until homogeneous.
Suppliers:
1) CIT SARL