INS HO8E - Rubinet

INS HO8E
INS HO8E
WALL MOUNTED POT FILLER
MODEL8ERBHOLorR
Ifyouneedassistancewithinstallation,replacementpartsorhaveany
questionsregardingyourRubinetproduct,pleasecallaCustomer
servicerepresentativeat:905-851-6781 tollfree 1-800-461-5901
orvisit www.rubinet.com
8ERBHOL
BEFORE YOU BEGIN
READ ALL DIRECTIONS PRIOR TO INSTALLATION. ANY
ALTERATIONS MADE TO THE CARTRIDGES AND
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
CAUSE DAMAGE OR IMPROPER INSTALLATION WHICH
WILL NULLIFY THE WARRANTY.
• Observeandadheretoalllocalbuildingandplumbing
codes.
• Shutoffmainwatersupply.
• Finishedwallreferstotheultimatefinishedsurface,Tile,
Marbleetc.
• Itisrecommendedthatthepipesbeflushedcleanpriorto
installation,inordertoavoidproblemswithdebrislater.
8ERBHOR
• ThisPotFillerisdesignedtobeusedincloseproximityto
ordirectlyaboveastovetop.The main consideration
therefore is what size is your largest pot and how high
off the surface of the stove top to mount the Pot Filler.
Thestandardheightofacountertopis36”astovetopis
generally2”abovethatsomounttheWallPlate16”above
thestovetopforatotalheightof54”fromthefloor.Allow
8”eithersideoftheWallPlateforthearmtoswing.Plan
ahead!
SPECIFICATIONS
Allbrassconstruction
Twohandlewall-mounted
Adjustablequarterturnceramicdisccartridges
1/2"NPTconnections
2.2gpmflowrateat60psi
REMOVAL OF FAUCET:
CARE OF FAUCET:
Alwaysturnthewatersupplyoff beforeremovingtheexistingfaucetor
disassemblingavalve.Openbothfaucethandlestorelievewater
pressureandtoensurethatthewaterhasbeensuccessfullyturnedoff.
Theuseofwarmwaterandasoftclothisallthatisrequiredtoclean
Rubinetproducts.Thepatinaofourlivingfinishes(OilRubbedBronze&
TuscanBrass)willchangeasaresultofnormaluse.ApplyingMineralOil
onoccasionwillcreateasofterlook,subtlecolorchangesandcharacter.
INS HO8E
1
2
FINISHED
WALL
7
2 3/4"
NIPPLE
SHOULD
PROTRUDE
3/4" - 1"
INS HO8E
8
ONE
TOOTH
OFF
Rough-Inplumbingshouldensurethat
the1/2"NPTNipple(notsupplied)
protrudenotlessthan3/4"andnot
morethan1"fromtheFinishedWall.
TheCartridgewillbeintheOFF position,
turnitON.
ALIGNED
GentlyforcetheHandle(unscrewthe
cartridge)tothedesiredON alignment.
Thisadjustmentshouldnotbemore
than25°.
Drilltwo7/16"holes13/8"eithersideof
theNPTNippleandinsertthetwo
Rawplugssupplied.
1 3/8"
RemovetheHandleandreplaceitclose
tobutonetoothofftheON positionas
showninFig.7.
TightenthePackingNutusinga17MM
wrench.
3
4
9
RAWPLUGS
WALL PLATE
TEFLON
WASHERS
WALL
MOUNT
BODY
SET SCREW
5
6
WALL
PLATE
PLUG
CARTRIDGE
PACKING
NUT
10
AssemblethePlatetothewallas
showninFig. 3 withtheSetScrewhole
atthebottom.
TIE DOWN
CAP
Don’tforgetthetwoTeflonwashers,
theseprotecttheplatefromscratching
bytheAcornNuts.
WASHER
LoosentheSetScrewintheTieDown
CapandremovetheCap.Thenremove
thesmall TeflonWasheronly.Leave
thelargerWasherontopoftheSwivel
Nipple.
SWIVEL
NIPPLE
POT
FILLER
ARM
ScrewtheWallMountBodyonthe
Nippleandalignverticallyasshownin
Fig. 5 usinga21MMwrenchonthe
plugprovided.
Securetheassemblybytighteningthe
SetScrewontheundersideoftheWall
PlatewiththeAllenKeyprovidedand
removethePlug.
LoosenthePackingNutonthesupplied
Cartridge-twofullturnsshouldbe
sufficient.InsertthecartridgeintheWall
MountBody.
PlaceoneoftheHandlesonthespline
oftheCartridgeandscrewitintothe
WallMountBodyuntillyoufeel
noticeable resistanceandstop.
11
12
PEG
FLANGE
SPACER
HANDLE
MOUNT
SLEEVE
CAP
CarefullyassemblethePotFillerArm
asshowntakingcarenottotearthe‘O’
RingsontheSwivelNipple.
Nowreplacethesmall TeflonWasher
overtheexposedthreadsthenscrew
ontheTieDownCapandsecureitby
re-tighteningtheSetScrew.
ScrewtheFlangeontotheCartridgeas
farasitwillgo,thenfittheTeflon
SpacerintotheFlangeasshown.Make
suretheCartridgeisintheOFF position
andassembletheHandleaccordingly
andsecurebytighteningtheSetScrew
withtheAllenKeyprovided.
AssembletheRoundHandleasshown.
TheHandleMountfirstandtightenthe
SetScrews,thentheSleevealigning
thesmallpegandholeandfinallyscrew
ontheCap.