Trampoline Installation Instructions Trampoline

Transcription

Trampoline Installation Instructions
Congratulations on purchasing an Oz Trampolines Product.
Following are detailed setup instructions for your trampoline.
Please ensure all boxes and parts are present before continuing.
Setting Up Your Trampoline Frame
Firstly lay all the circular parts of the
trampoline frame on the ground as
shown.
Then proceed to screw each piece together working in either a clockwise or
anti-clockwise direction.
Continue until you come to the last piece
to be screwed together.
When you come to the last piece to
be screwed together, if it is not lining
up correctly, simply lift this side of the
frame up, and push the opposite side
into the ground.
This will help line up the side you are
trying to piece together and will then slot
together.
You should now have a nicely completed
circular frame, as shown here.
The number of pieces you should have:
6 & 8FT = 6 pieces
10, 12 & 14FT = 8 pieces
16FT = 12 pieces
www.oztrampolines.com.au
1300 393 004
It is now time to start putting the legs together.
For each “U” shaped leg you should have 2 uprights. These are screwed together with
the supplied screws.
Fig 3 shows the orientation of which ends join together.
As you complete the assembly of each leg lay
them down on the ground near the trampoline.
This makes it easy once completed to then
attach the legs to the circular part of the
frame.
Once at this stage you will be ready to attach
the legs to the frame.
Note:
6 & 8FT = 3 legs
10, 12 & 14FT = 4 legs
16FT = 6 legs
1300 393 004
Insert trampoline leg into the corresponding
joints.
Ensure that you have the legs around the
correct way, as pictured below.
You can see here the screw holes must be
pointing towards the centre of the trampoline.
When lined up screw in 1 of the supplied
screws.
Tip: If the holes are not lining up tap with
a rubber mallet or simply lift the frame and
bang it down on the ground to force the leg
upright further into the frame piece.
Continue now to the opposite leg and repeat
the process.
This can be handy especially if your assembling the trampoline on your own.
You now have your trampoline frame
assembled.
Well Done.
1300 393 004
As you see pictured here the frame is not
quite sitting together nicely.
We are going to fix that quite easily. What
you need to do now is go around the circular part of the frame and loosen these
screws, so they are not tight.
Further on we will explain why.
Let’s go ahead and add our springs. You
will see pictured here 1 end of the springs
looks like a “ C “ ( to the left hand side of
the picture ).
This is the end that hooks into your trampoline frame.
Place all your springs in the slots on your
trampoline frame.
It will end up looking like the pictures
below.
1300 393 004
Mat Assembly
Attach a spring onto your trampoline mat
at both 12 oclock and 6 oclock, as pictured
here.
Now attach a spring at both 3 and 9 oclock.
Attaching any trampoline mat in this
fashion applies a nice even pressure on both
the mat and also the frame.
IMPORTANT
It is an imperative part now in each section
where the springs are not attached, to count
both the number of springs and the
number of triangles on the mat.
1300 393 004
To understand why, in this picture we had
16 unhooked springs, but only 15 vacant
triangles on the mat.
So in this picture we needed to attach the
spring to the right, onto the mat where the
pictured spring is attached.
So now what we are left with is 15 unhooked springs and 15 vacant triangles on
the mat.
Now repeat this process in the other three
quaters of the trampoline.
This will ensure when you start to attach
the rest of your springs that it is the correct number of corresponding triangle
attachments on the jumping mat.
Now attach 1 spring at approximately 2
oclock, 8 oclock, 4 oclock and 10 oclock.
Just remember to count and check the
number of springs versus the number of
triangles left in each gap.
1300 393 004
Continue around the trampoline working between each gap in a set of springs. As
mentioned this applies an even pressure on the mat and also the frame.
Once you only have 2 maybe 3 springs to go in each gap, you may now simply work
around the trampoline in a clockwise fashion adding each spring in succession.
Do not do this part to early or you will find it too hard to attach the springs as you
make your way around the trampoline.
REMEMBER EARLIER ON WE MENTIONED TO LOOSEN THE
SCREWS HOLDING THE CIRCULAR PART OF THE FRAME
TOGETHER - HERE IS WHY!
You will see now the frame
has joined together nice
and tight.
This has happened from the
the mat and springs
applying tension to the
whole frame.
If you left the screws done
up nice and tight the frame
would not be able to sit into
itself.
1300 393 004
As a side note, before tightening the circular frame
screws check that all legs are sitting straight.
If they are not straight simply move them till they do
line up straight and then tighten up the screws.
What you will now end up with
is a well constructed frame and a
nice taught trampoline mat.
NOW IT’S TIME TO CONTINUE
1300 393 004
TRAMPOLINE PADS
Lay your trampoline pads around the edges
of your trampoline.
Oz Trampolines Safety pads tie onto the
trampoline frame with elastic ties.
Tie the pads around the frame as pictured
here.
Continue around the trampoline in the one
direction.
This will ensure that the pads sit evenly on
your trampoline.
Proceed around the trampoline folding
down the side flap of the trampoline pads.
You will now have a trampoline looking
similar as pictured here.
Note: Colors and sizes obviously will differ.
1300 393 004
SAFETY NET INSTALLATION
Lay the net down on the trampoline ready
to start inserting the upright safety poles.
The first sleeve to start with would be the
one with the zip opening.
Also line this up with the leg of the
trampoline where you wish to have the
opening in the safety net.
At this point join all your safety poles together, they come in 2 pieces.
A handy tip is join them together as in Fig 1, and then holding the top piece to gently
bang it on the ground, this will then help them join as in Fig 2.
Once you have joined all your safety poles
together lean them on the trampoline at the
points where the uprights of the legs are.
As this is how the poles affix to the trampoline.
1300 393 004
To streamline your installation lay 2 safety
pole clamps at the base of each leg upright
as shown here.
Start by sleeving one pole at a time into
the sleeves of the safety net.
TIP: Hold the pole at the point where the
pole and pole padding are. This stops the
pole padding sliding down as you slide the
pole into the net sleeve.
As you attach the clamps be sure to make
sure they are in alignment.
Do not have them tightened to your trampoline as pictured here and this will make
the safety poles crooked.
The clamps should end up pointing outwards from the legs and inline as shown
here.
Continue around the trampoline one
safety pole at a time.
1300 393 004
As you tighten each safety pole to the
trampoline ensure the netting to the
left and right hand side of you is sitting
down past the edge of the frame.
Continue to work around the trampoline one pole at a time in the same direction.
As you work your way around each
section of the netting will start to take
shape.
When you get to the point of having 3
poles left to go ( on a 16ft trampoline
make it 4 ), you now need to sleeve each
remaining pole into the sleeves.
Once you have placed each pole in the
remaining sleeves simply let them sit
there on there own.
Now continue clamping the poles to
the uprights as you were before.
1300 393 004
As pictured here you can see we are up to
the last safety pole.
The reason for putting the last 3 - 4 poles
in their sleeves is when you get to the last
pole, because the the whole circumference
of the net has tightened up, trying to put a
2 metre pole into a sleeve which is only 1
metre off the ground would be very difficult.
Once you have completed that part go around and attach the safety clips on the
bottom edge of the net to the underside of the trampoline.
These affix onto the triangles of the trampoline mat as shown. Do this all the way
around the trampoline.
At this point go around the
trampoline and place the
protective blue clips in the ends of
the clamps.
1300 393 004
So far so good.
You will have the main part of your trampoline
setup now.
POCKET SURROUND AND WEATHER COVER
To start with the pocket surround, lay it on
the ground on the section you wish the
pockets to be.
A tip here is to start tieing it to the trampoline on the next leg. In this case it will be the
leg to the left in this picture.
It will become clear shortly why we do this.
Start by tieing to the upper most part of the
pole first.
To make it easy to tie on, loop each strap
behind the pole.
Then tie it in a shoelace knot or a bow.
1300 393 004
In this instance continue in a clockwise
order tieing on each panel as you go.
Continue this all the way around the
trampoline until you reach where you
started from.
Why we started on the first panel to the
left is as you can see it becomes easier at
the end.
Starting from the top join each tie completing the process of putting a pocket
surround on your trampoline.
Now pop the kids toys or their shoes in
the pockets and away you go.
Place your ladder on the trampoline and
let the kids go wild.
Congratulations you have just installed
your trampoline.
1300 393 004
Trampoline Extras
Weather Cover
Layout your weather cover inside the
trampoline. At different points around
the weather cover there are elastic
straps with hooks on them.
These affix underneath the trampoline.
Pull the elastic clip through and clip it
onto a triangle on the jumping mat, as
pictured here.
TIP: If you are unable to get your hand
underneath the net edge simply undo
one of the clips holding your
trampoline safety net.
Then replace after fastening the
weather cover.
There it is all protected from the
weather.
1300 393 004

Trampoline Installation Instructions Trampoline

Transcription

Similar documents

2.6 Partial Products and Distributive Propery

information on our Additional Programs

JumpSport AlleyOOP Sports VariableBounce Trampoline

Untitled - Lumasol

Party Invitation.

Inground Trampoline Installation Timeline

Trampoline Safety

bigredinvite2017 - Airborne Academy

Week 3 - Merrick Woods