Documentation

mCubed Home
Seite 1 von 15
Configuration assistant
An assistant guides you step by step through the customization process:
Tacho function
Speed signal ca be monitored for each fan channel.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 2 von 15
Manual Mode and Monitoring
You can take over control and immediately active manual controls and influence the fan speeds directly.
Calibration of sensors
The sensors must be calibrated according to the distance between the sensors and the origin of heat. This is easily accomplished with softwar
system monitors that come with the mainboard (like Asus Probe, Intel Active Control, and more).
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 3 von 15
Definition of limits
Here you can define the temperature limits. Above these limits all fans speeds will be operating at 100%. Under these limits the speed will ran
according to the measured temperatures. A delay (hysteresis) can be defined with "leave“ values.
Assignment between sensors and fans
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 4 von 15
Sensors can be assigned to the 4 fan channels in any possible way, giving you a free configuration of sensors to channels. You can even confi
them so as to have several sensors connected to a single channel, or have a single sensor being used by several channels.
also assignable using a comprehensive matrix:
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 5 von 15
Speed-Temperature response curves editable
The user can chose from a variety of predefined profiles or can freely design their own curve with 5 definition points which connect to a curve
You can design a different curve for every channel. The input of the curve is the measured temperature (the highest if more than one sensor
related to the actual channel). The output of the curve is the performance of the fans (0-100%)
Control to target temperature
You can control each fan channel to meet a certain target temperature.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 6 von 15
Control with MBM mainboard internal sensors
You can use the internal mainboard sensors to control the speed. All you need is Motherboard Monitor (MBM). Just assign the MBM sensor to y
fan channels:
The tool MBM has to be installed and has to run in parallel. Only values, which MBM delivers can be analysed by the T-Balancer software.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 7 von 15
Water cooling system support
You can connect up to 2 flowmeters from different manufacturers. You can also adjust the impulse rate to your model. In addition you have a
hardware emergency switch off and can connect up to 6 analog water temp probes.
Controlling CCFLs
You can also control CCFLs instead of fans. You can choose this option for each channel. Load an effect or create your own with an effect edito
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 8 von 15
Changing Profiles with timing
You can plan different profiles for different times. The T-Balancer will change automatically the profiles.
Ping the digital sensors
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 9 von 15
Define Quickbuttons
You can assign to each of the 5 quickbuttons profiles or navigation menues.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 10 von 15
Individual navigation profiles
Here you can disable all navigation menues, which you do not need. This adapts the software interface to your needs.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 11 von 15
Coastdown control system
You can configure, if your system should accelerate to 100% fan speed while closing the TBAN software.
blows all remaining warm air out of the PC.
FanAmp support
If you want to connect an FanAmp to one of your fan channels, then you have to invert the signal. Sig
invertation changes 100% to 0% and 0% to 100%. Please do this only for the channels, which are con
to the FanAmp, otherwise your TBAN will react the wong way.
Connect the FanAmp to a channel brings more power and true analog voltage signals to the fans or w
pumps.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 12 von 15
Configuration of the miniNG
The miniNG works completely autonom and can also be operated without the T-Balancer. But if you own a T-Balancer you can make all
configurations with Software and you can create new profiles and save them to the miniNG.
bigNG support
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 13 von 15
Integration with JaLCD
You can show the actual values like temperature, speed, alarm over a LCD with the software JaLCD.
JaLCD is Freeware and supports the following LCDs:
z HD44780-compatible LCD www.matrixorbital.com and
z Crystalfontz serial displays www.crystalfontz.com
jaLCDs can show information like: T-Balancer temperatures and speed, CPU speed and -usage, memory, HDD Infos, date/ time, upload
speed, MBM values, Winamp infos, eMail infos, Newstickers, TV program and much more.
Integration with LCDC
Many Thanks to Andrew Powell, who provided an interface to LCDC:
http://www.plasticrandom.net/plugins.php?action=viewplugin&pid=42
Allows for retrieval of:
- Alarm State
- Alarm Description
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 14 von 15
- All Digital and Analogue Temps - Names, Values
- 2 Flow meters - Names, Rates, Units
- 4 Fans - Names, Temps and Percentage
Integration with Samurize
Over an interface to Samurize you can choose of many desktop motives to monitor T-Balancer values.
Integration with iMON VFD
iMON VFD is the most advanced IR receiver and VFD display device in the market. It not only delivers IR signal to PC but also shows various u
information through VFD. It is designed to fit into the 5.25” disk drive bay of PC. It shows ‘Graphical EQ’, ‘System Info’, ‘Media Info
‘News’, ‘World City Time & Weather’ and more. All the information could be displayed automatically according to the scenario. Of course, user
choose the specific information with remote controller too. And one more feature of this iMON VFD is use can boot a PC with preset schedule.
this scheduled turn on feature, you can listening music or recording TV channel by Multi-Median.
With the following interface, provided by Robin, you can also monitor T-Balancer values:
http://drunkardswalk.dk/iMonInterface/iMonInterface.html
Integration with LCD Smartie
Many thanks to Peter in the forum Silenthardware.de. Download here.
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012
mCubed Home
Seite 15 von 15
Monitoring over net
With NView you can monitor each T-Balancer in a network from any PC.
Analysing history
With an Excel tool you can read the history data out of the database and analyse it.
Linux support
Your are invited to support the Linux developments. Driver, communication protocol and programming examples are
http://sourceforge.net/forum/forum.php?thread_id=1271826&forum_id=462785
http://www.t-balancer.com/english/produkt_tban_sw.htm
27.02.2012