- Tractor Supply

VERTICAL/HORIZONTAL LOG SPLITTERS
22, 28 & 35 TON MODELS
MODEL NUMBERS
1032822, 2152374 and 1083946
Owner’s Manual
ASSEMBLY & OPERATING INSTRUCTIONS
WARNING: All operators must read this manual before operating this log
splitter. Follow the safety instructions in the manual and in decals attached
to the product. Failure to do so could result in serious injury or death.
Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-4
Intended Use ....................................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
Safety Decals ....................................................................................................................... 1-2
General Safety ......................................................................................................................
3
Work Area ............................................................................................................................. 3
Preparation of the Log .........................................................................................................
3
Operation of the Log Splitter .................................................................................................. 3
Repair and Maintenance Safety ............................................................................................. 3-4
Fire Prevention ..................................................................................................................... Towing Safety ...................................................................................................................... 4
Assembly Instructions ...................................................................................................................... 5-7
Replacement Parts ...........................................................................................................................
8-10
Operating Instructions ....................................................................................................................... 11-13
4
Engine Oil Recommendations ................................................................................................ Hydraulic Oil Recommendations ............................................................................................
11
Starting Instructions ............................................................................................................... 11-12
Operation .............................................................................................................................. 12
11
Towing ......................................................................................................................................
13
Maintenance ..........................................................................................................................................
13
Warranty Service Information .................................................................................................................
13
Specifications ......................................................................................................................................... Back Cover
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals before
assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not
allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a
log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you
have any questions concerning safe operation. To get answers to any questions, call our technical
support department at 1-800-525-8322.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
This is the SAFETY ALERT SYMBOL. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided,
will result in serious injury or death.
WARNING indicates a hazardous situation which, if not avoided,
could result in serious injury or death.
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE is used to address practices not related to personal
injury.
INTENDED USE
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only. Any other use can
cause serious injury or death.
PERSONAL PROTECTIVE EQUIPMENT
BEFORE operating this log splitter, make sure that you wear safety gear such as goggles or safety glasses, steel toed
shoes and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operating this log splitter.
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Contact SpeeCo at 1-800-525-8322 for replacement decals.
PART NUMBER: S52062500
LOCATION: TOP, FRONT END OF TONGUE
Page 1
PART NUMBER: S52062200
LOCATION: TOP OF CYLINDER
PART NUMBER: S52062300
LOCATION: STRIPPER PLATE,
OPERATOR SIDE
PART NUMBER: S52062600
LOCATION: STRIPPER PLATE,
NON OPERATOR SIDE
PART NUMBER: S52062400
LOCATION: HYDRAULIC TANK
LOWER TANK, RIGHT CORNER
PART NUMBER: S52062100
LOCATION: TOP OF HYDRAULIC
CYLINDER
Page 2
GENERAL SAFETY
• ALWAYS keep the operator’s manual nearby for reference. Reread the manual periodically.
• ALWAYS keep all bystanders and pets a minimum of 10 feet away from your work area when operating this log •
•
•
•
splitter. Only the operator is to be near the log splitter during use.
NEVER allow adults lacking proper instructions and understanding to operate this log splitter.
NEVER actuate the control unit until all people are clear of the work area.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away from all moving parts when operating this log splitter.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication or when otherwise not alert enough to operate dangerous machinery.
WORK AREA
• NEVER operate the log splitter on slippery, wet, muddy or icy ground.
• NEVER operate the log splitter in an enclosed area. Exhaust fumes contain carbon monoxide which can be deadly when inhaled.
• ONLY operate the log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall off.
• ONLY operate the log splitter in daylight or under good artificial light.
• ALWAYS keep the work area clean. Remove split wood around the log splitter immediately so that you don’t stumble over it.
PREPARATION OF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 25-1/2 inches in length.
ENGINE
OPERATION OF THE LOG SPLITTER
ONLY operate the log splitter from the operator zone as
shown in the diagram. The operator has the safest and
most efficient access to the control valve and the beam
in this location. Operating the log splitter in another
location can result in serious injury or death.
FOOT PLATE
TONGUE
BEAM
OPERATOR ZONE
•
•
•
•
•
•
•
•
•
•
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke as this could result
In serious injury or death.
NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a log.
NEVER attempt to load the log splitter when the ram or wedge is in motion.
NEVER use your foot, a rope or any extension device to operate the control lever on the valve. Only use hand.
NEVER move the log splitter while the engine is running. Shut off the engine if you are leaving the log splitter, even for a short period of time.
• NEVER touch the muffler and other hot areas of the engine during operation. Wait until the engine cools down.
GENERAL REPAIR
• NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
• NEVER alter your log splitter in any manner. Such alterations may cause your log splitter to be unsafe and will void the warranty.
• NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer and is within safety limits. Refer to the engine owner’s manual for your particular log splitter.
• NEVER perform any service or repair on your log splitter without first removing the spark plug wire.
• ALWAYS perform all recommended maintenance procedures before using your log splitter.
• ALWAYS check the level of hydraulic oil and engine oil before operation.
Page 3
.
• ALWAYS periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight.
• ALWAYS replace all damaged or worn parts immediately.
• ALWAYS be sure that all replacement parts meet manufacturer’s specifications.
MAINTENANCE & SAFETY
• The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.
• NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing SERIOUS INJURY or even DEATH.
Leaks can be safely detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
• NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. The tank could contain hot oil under pressure which could result in serious injury.
• NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified service technician should perform this adjustment.
• ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or reaction can develop if proper medical treatment is not administered immediately.
• ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
FIRE PREVENTION
• NEVER operate your log splitter near a flame or spark or smoke during operation. Hydraulic oil and gasoline are
flammable and can explode.
• NEVER fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.
• ONLY refuel your log splitter in a clear area with no gas fumes or spilled gas.
• ALWAYS replace the gas cap securely.
• If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition until the spilled gas has evaporated.
• ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
• ALWAYS clean wood debris from the muffler area of the engine.
• ALWAYS store gasoline in an approved, tightly sealed container and away from heating appliances. Store the
container in a cool, dry place.
IMPORTANT NOTE – (spark arrester):
As a precautionary measure against possible flying sparks, always take a Class B fire extinguisher with you when
operating this log splitter in dry areas. This log splitter is equipped with an internal combustion engine and should not be used on or
near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by
the operator. In the state of California, a spark arrester is required by law. Other states have similar laws. Federal laws apply on federal
lands. A spark arrester muffler is optional and available as an accessory at your nearest engine dealer. Always check the legal
TOWING SAFETY
•
•
•
•
NEVER attempt to move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.
NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter.
NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could
result in loss of control, damage to the equipment, or serious injury or death. Adjust towing speed for terrain and
conditions. Be extra cautious when towing over rough terrain, especially railroad crossings, and avoid sharp turns and
steep angles when towing your log splitter.
• NEVER exceed weight capacity of ball or load limits of coupler.
• ALWAYS confirm coupler tightness each time before towing and after towing 50 miles.
• ALWAYS disconnect your log splitter from the towing vehicle before operating it.
• ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
• ALWAYS allow for added length of your log splitter when turning, parking, crossing intersections and in all driving situations.
• ALWAYS use safety chains when towing your log splitter.
• ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
• ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing
vehicle and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning.
Always use a Class I, 2” ball with this log splitter.
• ALWAYS replace ball or coupler if damaged.
• ALWAYS turn the fuel shut off valve on the engine to the “OFF” position before towing the log splitter. Failure to do
so may result in flooding the engine.
Page 4
ASSEMBLY INSTRUCTIONS
NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become necessary to disassemble the unit for repair or replacement of parts. The drawings in this manual are for
reference only. Some of the components on your log splitter may look slightly different.
5
ITEM NO. DESCRIPTION
QTY.
1
Beam Assembly
1
2
Beam Lock Assembly 1
3Tank Assembly 1
4
Tire and Wheel 2
5
Tongue Assembly
1
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or delivering carrier.
STEP 2: Attach the two wheels (2) to the tank assembly (1) wheel spindles using the 3/4” light flat washers (3) ,3/4” NF slotted nuts (4), 1/8” x 1-1/2” cotter pins (5) and the hub caps (6). These items are in the hardware package. Tighten the slotted nuts and make sure the wheels rotate freely.
ITEM NO. 1
2
3
4
5
6
DESCRIPTION
Tank Assembly
Wheel Assembly 3/4” Light Flatwasher 3/4” Slotted Nut
1/8” x 1-1/2” Cotter Pin
Hub Cap
QTY.
1
2
2
2
2
2
Page 5
STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock washers (3) and two 1/2” hex nuts (4). Tighten.
STEP 4:
ITEM NO.
DESCRIPTION
QTY.
1
2
3
4
5
Tank Assembly
1/2” NC x 4-1/2 Hex Bolt
1/2” Lock Washer 1/2” NC Hex Nut Tongue Assembly
1
2
2
2
1
Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam is stable and on a level surface. Remove the pivot pin (3) and clip pin (2) from the tank assembly. Roll
the tongue/ tank assembly into position between the two tabs on the beam (1). Slide the pivot pin (3) through the aligned holes and lock in place with the clip pin (2).
ITEM NO.
DESCRIPTION
QTY
1Beam Assembly1
2
1/2”-3/4” R Clip Pin
1
3Pivot Pin1
Page 6
STEP 5: Connect the end of the 1/2” ID x 38” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve. See illustrations below.
STEP 6: Slide one hose clamp on the end of the 3/4” x 56” hydraulic return hose (2) that comes from the fitting on the filter. Then connect the hose to the fitting on the valve.Tighten hose clamp. See illustrations below.
Area of
Detail
ITEM NO. .
1
2
3
DESCRIPTION
DETAIL A
SCALE 1:3
QTY.
1/2” x 38” Pressure Hose
3/4” x 56” Return Hose
Worm Gear Clamp
1
1
3
STEP 7: If you have the 22 ton model (1076995), skip this step.
Attach the beam lock (1) to the bottom side of the beam as shown in the diagram using the two 1/2” x 1-1/4” Grade 5 hex cap bolts (4), the two 1/2” lock washers (3) and the two 1/2” hex nuts (2). Lower the beam onto the tongue. Position the beam lock assembly on the tongue and tighten hardware. The beam lock is used on the 28 and 35 ton models only. NOTE:The 22 ton model (1076995) uses a pin on the tongue that is locked in place with a lynch pin.
ITEM NO. DESCRIPTION
QTY.
1Beam Lock1
2
1/2” Hex Nut
2
3
1/2” Lock Washer
2
4
1/2” x 1-1/4” Bolt
2
Page 7
REPLACEMENT PARTS
TANK/ENGINE ASSEMBLY BREAKDOWN
dĂŶŬΘŶŐŝŶĞƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
/ƚĞŵEŽ͗ ϮϮdWĂƌƚEŽ͘ ϮϴdWĂƌƚEŽ͘ ϯϱdWĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
^ϰϬϭϭϴϴϬϬ
ϭ
dĂŶŬ
^ϬϳϭϬϮϮt
Ϯ
WŝǀŽƚWŝŶ
^ϬϳϬϵϮϰϬϬ
ϯ
ϭͬϮŝŶdžϯͬϰŝŶ,ĂŝƌƉŝŶŽƚƚĞƌWŝŶ
^ĞĞĞůŽǁ
ϰ
ŶŐŝŶĞΘWƵŵƉƐƐĞŵďůLJ
^ϭϳϬϱϱϬϬϬ
ϱ
ϱͬϭϲŝŶdžϭͲϭͬϮŝŶ'ϱ,ĞdžŽůƚ
^ϭϳϬϰϬϴϬϬ
ϲ
ϱͬϭϲŝŶ&ůĂƚtĂƐŚĞƌ
^ϭϳϬϮϬϳϬϬ
ϳ
ϱͬϭϲͲϭϴhEELJůŽĐŬEƵƚ
^ϯϵϬϯϰϵϬϬ
ϴ
ϯͬϰŝŶ,ĞdžEŝƉƉůĞ
^ϯϵϬϲϬϰϬϬ
ϵ
&ŝůƚĞƌƐƐĞŵďůLJ
ϭϬ
ϯͬϰŝŶEWddžϯͬϰŝŶdƵďĞϵϬͲĚĞŐ
^ϯϵϬϯϮϬϬϬ
ϭϭ
ϯͬϰEWdƚŽϯͬϰŝŶ/dƵďĞ&ŝƚƚŝŶŐ
^ϯϵϬϯϴϯϬϬ
ϭϭ
^ϯϵϬϯϴϭϬϬ
ϯͬϰEWdƚŽϭŝŶ/dƵďĞ&ŝƚƚŝŶŐ
ϭϮ
ϯͬϰŝŶZĞƚƵƌŶ,ŽƐĞ
^ϯϵϬϮϳϰϬϬ
^ϯϵϬϮϳϱϬϬ
ϭϯ
ϯͬϰŝŶWƌĞƐƐƵƌĞ,ŽƐĞ
^ϯϵϬϮϳϯϬϬ
ϭϰ
ϯͬϰŝŶ^ƵĐƚŝŽŶ,ŽƐĞ
ϭϰ
^ϯϵϬϯϴϵϬϬ
ϭŝŶ^ƵĐƚŝŽŶ,ŽƐĞ
ϭϱ
tŽƌŵ'ĞĂƌůĂŵƉ
^ϯϵϬϯϭϲϬϬ
YƚLJ
ϭ
ϭ
ϭ
ϭ
ϰ
ϴ
ϰ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϯ
PUMP/ENGINE ASSEMBLY BREAKDOWN
ŶŐŝŶĞΘWƵŵƉƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
/ƚĞŵEŽ͗ ϮϮdWĂƌƚEŽ͘ ϮϴdWĂƌƚEŽ͘ ϯϱdWĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
ϭ
^ϯϵϬϱϱϬϬϬ
<ŽŚůĞƌ^,Ϯϲϱ
ϭ
ϱϲϲϴϴϬ
<ŽŚůĞƌ,ϮϳϬ
ϭ
^ϯϵϬϱϰϮϬϬ
,ŽŶĚĂ'ϭϵϬ
ϭ
^ϯϵϬϱϲϲϬϬ
<ŽŚůĞƌ,ϯϵϱ
Ϯ
^ŵĂůůWƵŵƉDŽƵŶƚ
^ϰϬϬϴϭϮϬϬ
Ϯ
^ϰϬϬϴϭϴϬϬ
>ĂƌŐĞWƵŵƉDŽƵŶƚ
ϯ
ϱͬϭϲ>ŽĐŬtĂƐŚĞƌ
^ϭϳϬϯϬϵϬϬ
ϰ
ϱͬϭϲŝŶdžϭŝŶhE&'ϱŽůƚ
^ϭϳϬϱϰϰϬϬ
ϱ
ϱͬϭϲdžϭͲϭͬϰhE&'ϱŽůƚ
^ϭϳϬϱϯϵϬϬ
ϲ
ϯͬϭϲŝŶdžϭŝŶ^Ƌ<ĞLJ
^ϰϬϬϯϰϴϬϬ
ϳ
ϯͬϰŝŶŽƵƉůĞƌŶŐŝŶĞ^ŝĚĞ
^ϰϬϬϴϯϱ>Ϭ
ϳ
^ϰϬϬϴϮϱ>Ϭ
ϭŝŶŽƵƉůĞƌŶŐŝŶĞ^ŝĚĞ
ϴ
ϮϮdΘϮϴdZƵďďĞƌ^ƉŝĚĞƌ
^ϰϬϬϴϯϰ>Ϭ
ϴ
^ϰϬϬϴϮϳ>Ϭ
ϯϱdZƵďďĞƌ^ƉŝĚĞƌ
^ϰϬϬϴϯϯ>Ϭ
ϵ
ϭͬϮŝŶŽƵƉůĞƌWƵŵƉ^ŝĚĞ
ϭϬ
ϭϭŐƉŵWƵŵƉ
^ϯϵϬϳϬϱϬ
ϭϬ
^ϯϵϬϳϬϵϬϬ
ϭϲŐƉŵWƵŵƉ
ϭϭ
^ϭϳϬϮϬϳϬϬ
ϱͬϭϲͲϭϴhEELJůŽĐŬEƵƚ
Page 8
YƚLJ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϰ
ϰ
ϰ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϰ
BEAM ASSEMBLY BREAKDOWN
ĞĂŵƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
/ƚĞŵEŽ͗ ϮϮdWĂƌƚEŽ͘ ϮϴdWĂƌƚEŽ͘ ϯϱdWĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
ϭ
ϭͬϮŝŶ,ĞdžEƵƚ
^ϭϳϬϭϬϱϬϬ
^ϭϳϬϯϬϯϬϬ
Ϯ
ϭͬϮŝŶ>ŽĐŬtĂƐŚĞƌ
^ϭϳϬϳϭϲϬϬ
ϯ
ϭͬϮŝŶdžϯŝŶ,ĞdžŽůƚ
ϯ
^ϭϳϬϱϲϲϬϬ
ϭͬϮŝŶdžϯͲϭͬϰŝŶ,ĞdžŽůƚ
^ϰϬϭϰϭϳϬϬ
ϰ
ϮϮdΘϮϴdtĞĚŐĞ
ϰ
^ϰϬϭϰϭϴϬϬ
ϯϱdtĞĚŐĞ
^ϯϵϬϯϮϬϬϬ
ϱ
ϯͬϰŝŶEWddžϯͬϰŝŶdƵďĞ&ŝƚƚŝŶŐ
^ϯϵϬϯϰϯϬϬ
ϲ
ϭͬϮŝŶEWddžϭͬϮŝŶEWdEŝƉƉůĞ
^ϯϵϬϰϳϭϬϬ
ϳ
sĂůǀĞ,ĂŶĚůĞ<ŝƚ
^ϯϵϬϰϬϲ^t,
ϴ
ƵƚŽͲZĞƚƵƌŶsĂůǀĞ
^ϯϵϬϯϵϬϬϬ
ϵ
ϰϱͲĚĞŐ^ǁŝǀĞů&ŝƚƚŝŶŐ
^ϯϵϬϯϰϳϬϬ
ϭϬ
ϭͬϮŝŶEWdƚŽ^ƚĞĞůdƵďĞ&ŝƚƚŝŶŐ
ϭϭ
ϭͬϮŝŶ^ƚĞĞůdƵďŝŶŐ
^ϯϵϬϯϰϲϬϬ
ϭϮ
^ϯϵϬϭϭϴ
ϰŝŶLJůŝŶĚĞƌǁͬ^ĂĨĞƚLJĞĐĂůƐ
ϭϮ
^ϯϵϬϭϭϵ
ϰ͘ϱŝŶLJůŝŶĚĞƌǁͬ^ĂĨĞƚLJĞĐĂůƐ
ϭϮ
^ϯϵϬϭϭϳ
ϱŝŶLJůŝŶĚĞƌǁͬ^ĂĨĞƚLJĞĐĂůƐ
ϭϯ
LJůŝŶĚĞƌWŝŶΘůŝƉƐ
^ϬϳϬϳϯϭϬϬ
ϭϰ
ϱϲϰϵϭϯ
ϮϮdĞĂŵǁŝƚŚĞĐĂůƐ
ϭϰ
ϱϲϱϴϴϯ
ϮϴdĞĂŵǁŝƚŚĞĐĂůƐ
^ϰϬϭϰϭϯ^
ϭϰ
ϯϱdĞĂŵǁŝƚŚĞĐĂůƐ
^ϰϬϭϮϳϱϬϬ
ϭϱ
ĞĂŵ>ŽĐŬ
^ϭϳϬϱϲϳϬϬ
ϭϲ
ϭͬϮŝŶdžϭͲϭͬϰ'ϱŽůƚ
^ϭϳϬϭϬϱϬϬ
ϭϳ
ϭͬϮŝŶ,ĞdžEƵƚ
^ϭϳϬϯϬϯϬϬ
ϭϴ
ϭͬϮŝŶ>ŽĐŬtĂƐŚĞƌ
YƚLJ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
Ϯ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
ϭ
Ϯ
Ϯ
Ϯ
WHEEL ASSEMBLY BREAKDOWN
/ƚĞŵEŽ͗
ϭ
Ϯ
ϯ
ϰ
ϱ
ϮϮd͕ϮϴdΘϯϱdtŚĞĞůƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
WĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
^ϰϬϬϯϭϮϬ
dŝƌĞΘtŚĞĞůƐƐĞŵďůLJ
^ϭϳϬϰϬϰϬϬ
ϯͬϰŝŶ&ůĂƚtĂƐŚĞƌ
^ϭϳϬϭϮϬϬϬ
ϯͬϰŝŶ^ůŽƚƚĞĚEƵƚ
^ϭϳϭϭϬϯϬϬ
ϭͬϴŝŶdžϭͲϭͬϮŝŶŽƚƚĞƌWŝŶ
^ϰϬϬϯϯϮϬϬ
,ƵďĂƉ
ZĞƉůĂĐĞŵĞŶƚtŚĞĞůĞĂƌŝŶŐ<ŝƚ
^ϰϬϬϯϬϵϬϬ
;ŶŽƚƐŚŽǁŶͿ
YƚLJ
Ϯ
Ϯ
Ϯ
Ϯ
Ϯ
Ϯ
Page 9
TONGUE ASSEMBLY BREAKDOWN
/ƚĞŵEŽ͗
ϭ
Ϯ
ϯ
ϰ
ϱ
ϲ
ϳ
ϴ
ϵ
ϭϬ
ϭϭ
ϮϮddŽŶŐƵĞƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
WĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
ϱϲϱϮϴϰ
DϭϬdžϭ͘ϱELJůŽĐŬEƵƚ
ϱϲϰϳϴϭ
dŽŶŐƵĞtĞůĚŵĞŶƚ
^ϰϬϭϮϲϬϬϬ
'ƌŽƵŶĚ^ƚĂŶĚ
^ϬϳϬϵϱϴϬϬ ϱͬϭϲŝŶdžϯͲϭͬϰŝŶ^ƋƵĂƌĞ>ŽĐŬWŝŶ
^ϰϬϬϯϰϲϬϬ
,ŝƚĐŚĂůůƐƐĞŵďůLJ
^ϰϬϬϯϮϯϬϬ
ϮϬ>ŝŶŬŚĂŝŶǁͬ,ŽŽŬ
ϱϲϱϮϳϱ
DϭϬdžϭ͘ϱdžϭϬϬŵŵ'ϱŽůƚ
ϱϲϱϮϳϲ
DϭϬdžϭ͘ϱdžϭϮϬŵŵ'ϱŽůƚ
ϱϲϱϮϳϳ
DϭϬdžϭ͘ϱdžϵϬϬŵŵ'ϱŽůƚ
ϱϲϱϮϴϲ
DϭϬ&ůĂƚtĂƐŚĞƌ
ϱϲϰϳϰϯ
^ƚĂďŝůŝnjĞƌWŝŶƐƐĞŵďůLJ
YƚLJ
ϯ
ϭ
ϭ
ϭ
ϭ
Ϯ
ϭ
ϭ
ϭ
Ϯ
ϭ
/ƚĞŵEŽ͗
ϭ
Ϯ
ϯ
ϰ
ϱ
ϲ
ϳ
ϴ
/ƚĞŵEŽ͗
ϭ
Ϯ
ϯ
ϰ
ϱ
ϲ
ϳ
•
Page 10
ϯϱddŽŶŐƵĞƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
WĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
ϱϲϱϮϴϰ
DϭϬdžϭ͘ϱELJůŽĐŬEƵƚ
ϱϲϱϮϳϱ
DϭϬdžϭ͘ϱdžϭϬϬŵŵ'ϱŽůƚ
ϱϲϱϮϳϲ
DϭϬdžϭ͘ϱdžϭϮϬŵŵ'ϱŽůƚ
ϱϲϱϮϴϲ
DϭϬ&ůĂƚtĂƐŚĞƌ
^ϰϬϭϲϳϮ
dŽŶŐƵĞtĞůĚŵĞŶƚǁͬ:ĂĐŬ
^ϰϬϬϯϰϲϬϬ
,ŝƚĐŚĂůůƐƐĞŵďůLJ
^ϰϬϬϯϮϯϬϬ
ϮϬ>ŝŶŬŚĂŝŶǁͬ,ŽŽŬ
YƚLJ
Ϯ
ϭ
ϭ
ϲ
ϭ
ϭ
Ϯ
ϮϴddŽŶŐƵĞƐƐĞŵďůLJWĂƌƚƐ>ŝƐƚ
WĂƌƚEŽ͘
ĞƐĐƌŝƉƚŝŽŶ
ϱϲϱϮϴϰ
DϭϬdžϭ͘ϱELJůŽĐŬEƵƚ
ϱϲϱϮϳϲ
DϭϬdžϭ͘ϱdžϭϮϬŵŵ'ϱŽůƚ
ϱϲϱϮϴϲ
DϭϬ&ůĂƚtĂƐŚĞƌ
^ϰϬϭϮϳϯϬ
dŽŶŐƵĞtĞůĚŵĞŶƚ
^ϰϬϬϯϰϲϬϬ
,ŝƚĐŚĂůůƐƐĞŵďůLJ
^ϰϬϭϮϳϰϬϬ
'ƌŽƵŶĚ^ƚĂŶĚ
^ϭϬϭϭϭϮϬϬ
ŝƌĐůŝƉZĞƚĂŝŶŝŶŐZŝŶŐ
^ϰϬϬϯϮϯϬϬ
ϮϬ>ŝŶŬŚĂŝŶǁͬ,ŽŽŬ
YƚLJ
Ϯ
Ϯ
ϲ
ϭ
ϭ
ϭ
ϭ
Ϯ
OPERATING INSTRUCTIONS
WARNING: Read and thoroughly understand all instructions and safety information before operating
this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate
this log splitter who has not read this manual. As with all power equipment, a log splitter can be
dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts or
questions concerning safe operation. Call our technical support department at 1-800-525-8322 to
address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
IMPORTANT:
This log splitter comes complete with hydraulic oil and engine oil. Please follow the instructions below for filling the hydraulic tank. Refer to the engine owner’s manual for information on adding oil.
CAUTION:
DO NOT START OR RUN THE ENGINE BEFORE ADDING OIL IN THE HYDRAULIC
RESERVOIR AND OIL IN THE ENGINE.
STEP 1: The hydraulic reservoir must be filled with oil before operation. AW46 hydraulic oil is recommended when oil is needed. Automatic
transmission fluid can be substituted and should be used instead of hydraulic oil when temperatures are below 32 degrees F.
Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir. Fill the hydraulic tank with approximately
3.5 to 4.0 gallons of hydraulic fluid
STEP 2: After the hydraulic reservoir and the engine crankcase are filled with oil, start the engine. The hydraulic pump should prime itself. With the engine running, move the hydraulic valve lever toward the foot plate. This will cause the cylinder to extend and expel air. When the cylinder
is fully extended, retract it. Repeat this procedure several times. An erratic movement of the cylinder indicates that there is still air in the system. Add about 1.0 to 1.5 gallons more. Five gallons will register just above the top fill line on the dip stick.The total capacity of the entire hydraulic system is 6.5 gallons. NOTE: If the tank is overfilled it will tend to expel oil from the breather cap when the cylinder is retracted.
Cycle the cylinder again until it has a constant speed indicating that all air has been expelled.
CAUTION:
WHEN TIGHTENING THE BREATHER CAP ON THE TANK, POINT THE HOLE AWAY FROM THE ENGINE
ENGINE OIL RECOMMENDATIONS (Kohler SH265, CH270 and CH395)
We recommend use of Kohler oils for best performance. Other high quality detergent oils of API service class of SJ or higher are acceptable. For
temperatures above 32 degrees F use an SAE 10W-30 oil, For temperatures below 32 degrees use an SAE 5W-30 oil. Using SAE 30 oil below 40
degrees F will result in hard starting and possible engine bore damage. For temperatures above 50 degrees F use an SAE 30 oil. Oil capacity for
SH265 and CH270 is 0.63 qt. (0.60 L). Oil capacity for CH395 is 1.16 qt. (1.11 L).
ENGINE OIL RECOMMENDATIONS (Honda GC190)
For temperatures above 40 degrees F use an SAE 30W oil. Using mutigrade oil may increase oil consumption. Using SAE 30W oil below 40 degrees
F will resuilt in hard starting and possible engine bore damage. For temperatures below 40 degrees F use an SAE 10W-30 or SAE 5W-30 oil. Oil
capacity is about 1.16 quart (1.1 liter).
STARTING INSTRUCTIONS (Kohler SH265, CH270 and CH395)
NOTE: REFER TO THE ENGINE OWNER’S MANUAL FOR COMPLETE INFORMATION ON STARTING,
MAINTENANCE AND TROUBLE-SHOOTING.
1) Move the fuel lever (if equipped) to the “ON” position.
2) Turn the engine on/off switch (if equipped) to the “ON” position.
3) For a cold engine put the throttle control midway between “SLOW” and “FAST.” Place the choke control into the “ON” position.
4) Turn engine on/off switch to “ON.” Slowly pull the starter handle to just past compression. STOP!
Return starter handle. Pull firmly with a smooth steady motion until it starts.
5) Gradually return the choke control to the “OFF” position after the engine starts and warms up.
6) For a warm engine put the throttle control bewteen “SLOW” and “FAST.” A warm engine usually does not require the choke on.
Page 11
STARTING INSTRUCTIONS (Honda GC190)
NOTE: REFER TO HONDA ENGINE OWNER’S MANUAL FOR COMPLETE INFORMATION ON STARTING,
MAINTENANCE AND TROUBLE-SHOOTING.
To Start a Cold Engine
1) Turn the fuel valve to the ON position.
2) Move the choke to the ON position.
3) Move the throttle control to the FAST position.
4) Pull the starter grip lightly until resistance is felt. Then pull rapidly to start engine.
5) Move the choke lever to the OFF position if it was used to start the engine as soon as it warms up enough and is running smoothly.
6) When engine starts, move the throttle to the FAST position. It is recommmended that the engine be operated in the FAST position for
maximum performance. To Start a Warm Engine
1) Move the throttle lever to the FAST position.
2) Leave the choke lever in the OFF position.
3) Pull the starter grip until the engine starts.
To Stop the Engine
1) Move the throttle lever to the SLOW position.
2) Move the throttle lever to the STOP position.
3) Turn the fuel valve to the OFF position.
CAUTION: TURN FUEL SHUT OFF VALVE TO THE “OFF” POSITION PRIOR TO TOWING. FAILURE TO DO SO MAY
RESULT IN FLOODING THE ENGINE.
NOTE: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood the throttle
should be set at the maximum speed to develop the horsepower required for the pump.
OPERATION
WARNING: See safety information related to operation of the log splitter on page 3 and 4 of this manual.
Make sure that you have the recommended personal protective equipment described on page 1.
1) Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tank is always on the lower side of the log splitter.
2) For horizontal operation place a log on the beam against the foot plate. Make sure the the log is securely on the foot plate and up against the beam. To split wood in the vertical position, release the pin on the beam latch ( 28 & 35 ton) located near the front end of the beam. For the 22 ton, model remove the lynch pin from the pin on the middle of the tongue. Carefully tilt the beam up until the foot plate is sitting squarely on the ground and the log splitter is stable. Place the log on the foot plate up against the beam. When the beam is returned to the horizontal position make sure the beam latch is securely locked down. See illustrations in Step 7 on page 9.
3) With the engine running, depress and hold the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.
IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump. Always use extra care when splitting
logs with unsquare ends.
NOTE: For operation in wooded areas, obtain a spark arrestor for the exhaust system. See the engine operating and maintenance manual and
check with your authorized engine service center. See also Fire Prevention on page 5 of this manual.
IMPORTANT: TO EXTEND THE LIFE OF THE HYDRAULIC CYLINDER, AVOID “BOTTOMING OUT” WEDGE
PLATE TO THE FOOT PIECE. TO CONFORM WITH INDUSTRY SAFETY RECOMMENDATIONS,
THE WEDGE STOPS 1.5 INCHES FROM THE END OF THE STROKE.
Page 12
TOWING
This log splitter is equipped with pneumatic tires, a Class I coupler (2 in. diameter ball required) and safety chains. Before towing, the safety chains
must be secured to the hitch or bumper of the vehicle. Local regulations should be checked regarding licensing, lights, towing, etc.Turn fuel shut off
valve on the engine to the “Off” position prior to towing. Failure to do so may result in flooding the engine. Do not exceed 45 mph when towing this
log splitter. See also Towing Safety on page 6 of this manual.
MAINTENANCE
1) Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will cause
severe damage to the pump.
3) Change the oil filter after the first 25 hours of operation. Thereafter change the oil filter every 100 hours or seasonally, whichever comes first
4) To drain the hydraulic oil, loosen the clamp on the hose coming from the fitting on the bottom of the tank. It is located just to the right of the oil filter.
5) If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter bolt that connects the wedge to the cylinder.
hose from the valve. The hose from the valve may need to be removed. Carefully lift the cylinder to allow the wedge to slide forward. The wedge can now be lifted off and sharpened.
6) Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather cap
from the tank and flush with kerosene or liquid detergent to remove the dirt.
7) See also Repair and Maintenance Safety on page 4 of this manual.
8) All replacement parts must meet manufacturer’s specifications.
IMPORTANT NOTICE
Warranty Repair and Service
Do not return this product to the store for warranty issues or repair. Call 1-800-525-8322 for the location of the
nearest service center.
Record the information below for future reference.
Model No. ____________________
Serial No. _____________________________
Date of Purchase _______________
Place of Purchase
_______________________
_______________________
_______________________
_______________________
Serial Number Label Location:
Tank plate below beam
Page 13
SPECIFICATIONS
Model No. 1032822
Model No. 2152374
Model No. 1083946
Engine
Kohler SH265 6.5 HP
Kohler CH395 9.5 HP
Pump
Two-Stage 11 GPM
Kohler CH270 7 HP
Honda GC190
Two-Stage 11 GPM
Cylinder
4 in. Diam. x 24 in. Stroke
4-1/2 in. Diam. x 24 in. Stroke 5 in. Diam. x 24 in.Stroke
Valve
Auto-Return
Auto-Return
Auto-Return
Maximum Splitting Force*
22 Tons
28 Tons
35 Tons
Maximum Log Length
25-1/2 in.
25-1/2 in.
25-1/2 in.
Cycle Time*
13 Seconds
17 Seconds
14 Seconds
Wheels
4.80 x 8 in. DOT Approved 4.80 x 8 in. DOT Approved
4.80 x 8 in. DOT Approved
Wedge
7 in. High
7 in. High
7 in. High
Beam Size
6 in. x 9 in.
6 in. x 9 in.
8 in. x 10 in.
Hydraulic Capacity
6.5 Gallons
6.5 Gallons
6.5 Gallons
Filter**
Spin-on Replaceable
Spin-on Replaceable
Spin-on Replaceable
Height
72 in. in Vertical Position
43 in. in Horizontal Position
72 in. in Vertical Position
43 in. in Horizontal Position
72 in. in Vertical Position
45 in. in Horizontal Position
Length
85 in.
85 in.
87 in.
Width
50 in.
50 in.
50 in.
Shipping Weight
525 lbs.
590 lbs.
660 lbs.
Two-Stage 16 GPM
* Tonnage and cycle times vary dependent upon mechanical and environmental conditions.
** Use replacement filter element TSC sku # 1822617.
Note: Huskee log splitters are manufactured by SpeeCo, Inc.
AA
Part No. 564534
Rev 0