Model GT 1175 Standard Slide Doors **with U30 Control

Transcription

S82 W18717 Gemini Drive
Muskego, Wisconsin 53150
Phone: (877) 622-2694
Fax: (888) 679-3319
www.nabcoentrances.com
Technical Support: (866) 622-8325
Model GT 1175
Standard Slide Doors
**with U30 Control**
Installation Manual
DN0079
WARNING
• Turn OFF all power to the Automatic Door if a Safety System is not working.
• Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO
trained technician. Failure to follow these practices may result in serious consequences.
• NEVER leave a Door operating without all Safety detection systems operational.
Part #15-9244-30
Rev. 10/27/15
THIS PAGE IS INTENTIONALLY LEFT BLANK
www.NabcoEntrances.com
Rev. 10-27-15
1175 Standard Slide Doors Installation Manual
Part #15-9244-30
Table of Contents
Warning Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
General Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
CHAPTER 1: SCOPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Section 1a: To the Installer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Section 1b: Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
CHAPTER 2: GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Section 2a: Parts of the Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Section 2b: Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Section 2c: U30 Microprocessor Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2d: Associated Manuals Part Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2e: Header Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2f: Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2g: Holding Beams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2h: Electric Lock (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Section 2i: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
CHAPTER 3: ASSEMBLE FRAME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Section 3a: Prepare to Assemble Door Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Section 3b: Assemble Door Frame (No Transom). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Section 3c: Assemble Door Frame (with Transom). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
CHAPTER 4: SECURE FRAME TO BUILDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Section 4a: Secure door Frame to Building. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Section 4b: Complete the Tie Rod Installation (For Transom Units only) . . . . . . . . . . . . . . . . . . . . . 4-16
CHAPTER 5: 120 VAC GENERAL WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
CHAPTER 6: WIRE THE SWITCH ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
CHAPTER 7: LAY DOWN THE THRESHOLD (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . 7-19
CHAPTER 8: INSTALL THE SIDELITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Section 8a: Full Open Sidelite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
i
Part #15-9244-30
Rev. 10-27-15
CHAPTER 9: INSTALL THE SLIDE DOOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Section 9e: Permanently install the Threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-30
Section 9f: Threshold Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-30
CHAPTER 10: INSTALL THE WEATHERING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-31
Section 10a: Apply Caulking Bead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-31
CHAPTER 11: INSTALL THE GLASS STOPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-32
Section 11a: Door Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-32
Section 11b: Transom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-32
Section 11c: Dust Protector Hoods (Clean Room). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-33
CHAPTER 12: ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-35
Section 12a: Adjust Preload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-35
CHAPTER 13: ELECTRIC LOCK WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-38
Section 13a: U30 with Magnetic Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-38
Section 13b: U30 with Fail Secure Electric Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-39
Section 13c: U30 with Fail Safe Electric Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-40
Section 13d: Strike Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-41
CHAPTER 14: GENERAL WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-42
CHAPTER 15: HANDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-48
ii
Rev. 10-27-15
Part #15-9244-30
WARNING LABELS
Warning labels are universal and used to alert an individual of potential harm to one’s self or to others. The following warning
labels are listed in a hierarchy order that defines the most potential danger first, and the least potential danger last. Please refer
to this page in the event that a warning label is displayed within this manual and further definition needs to be explained.
DANGER
Indicates potentially dangerous situations. Danger is used when there is a hazardous situation
where there is a high probability of severe injury or death. It should not be considered for property
damage unless personal injury risk is present.
WARNING
Indicates a hazardous situation which has some probability of severe injury. It should not be
considered for property damage unless personal injury risk is present.
CAUTION
Indicates a hazardous situation which may result in a minor injury. Caution should not be used
when there is a possibility of serious injury. Caution should not be considered for property damage
accidents unless a personal injury risk is present.
Attention: A situation where material could be damaged or the function impaired.
Notice: Indicates a statement of company policy as the message relates to the personal
safety or protection of property. Notice should not be used when there is a hazardous
situation or personal risk.
Note:
Indicates important information that provides further instruction.
iii
Part #15-9244-30
Rev. 10-27-15
GENERAL SAFETY RECOMMENDATIONS
WARNING
Read this “General Safety Recommendations” section before installing, operating or servicing the
automatic door. Failure to follow these practices may result in serious consequences.
Notice: Read, study and understand the operating instructions contained in, or referenced
in this manual before operating. If you do not understand the instruction, ask the
installing qualified technician to teach you how to use the door.
WARNING
Do not install, operate or service this product unless you have read and understand the General
Safety Recommendations, Warning Labels, Installation and Operating Instructions contained in this
manual. Failure to do so may result in bodily injury, or property damage.
Notice: This manual and the owner’s manual must be given to and retained by the purchasing
facility or end user.
►►If the door appears broken or does not seem to work correctly, it should be immediately
removed from service until repairs can be carried out or a qualified service technician is
contacted for corrective action.
►►Disconnect power at the fused disconnect during all electrical or mechanical service.
When uncertain whether power supply is disconnected, always verify using a voltmeter.
►►All electrical troublshooting or service must be performed by qualified electrical
technicians and must comply with all applicable governing agency codes.
►►It is the responsibility of the installing door technician to install all warning and
instructional labels in accordance with ANSI 156.10.
►►It is the responsibility of the purchasing facility or end user to keep warning and
instructional labels and literature legible, intact and with the door.
DANGER
iv
►►Replacement labels and literature may be obtained from local NABCO Entrances, Inc.
distributors. If the name of the local distrubutor is unknown, contact NABCO Entrances,
Inc. at 1-877-622-2694 for assistance.
Do not place finger or uninsulated tools inside the electrical controller. Touching wires or other
parts inside the enclosure may cause electrical shock, serious injury or death.
Rev. 10-27-15
Part #15-9244-30
CHAPTER 1: SCOPE
Section 1a: To the Installer
The purpose of this manual is to familiarize the installer and purchaser with the proper installation and
operation of this system. It is essential that this equipment be properly installed and operational before
the door is used by the public. It is the installer’s responsibility to inspect the operation of the entrance
system to be sure it complies with any applicable standards. In the United States, ANSI Standard 156.10
covers the GT-1175 Slide Door System. Other local standards or codes may apply. Use them in addition to
the ANSI standard. The GT-1175 is listed with the Underwriters Laboratory and is identified as such on
the label.
Instruct the building owners and operator on the essentials of the operation of the door and this device.
The owner should follow these instructions to determine whether the door is operating properly and
should immediately call for service if there is any malfunction. All installation changes and adjustments
must be made by qualified, NABCO trained technicians.
Section 1b: Objective
The GT-1175 Standard Slide Door system is designed to be installed within a Rough Opening of a Building.
The door function is controlled by the U30 Microprocessor Control. This control offers many features to
accommodate most installation options. This manual offers step by step instructions.
Scope
1-5
Part #15-9244-30
Rev. 10-27-15
CHAPTER 2: GETTING STARTED
►►Manufactured out of:
•
Aluminum
•
Opening of Building
•
Bi-Part: (2) Slide Doors that slide apart from the center with (2) Sidelite Panels.
►►Installed within:
►►Mechanical Configurations:
•
Single Slide: (1) Slide Door that slides to the right or left with (1) Sidelite Panel.
►►Extrusion Configurations:
•
Pocketed Jamb Tubes
•
Slick Jamb Tubes
►►Emergency Egress:
•
Full Open: Both the Slide door and Swing Sidelite break out for emergency egress.
•
Fixed Sidelite: Fixed Sidelite is secured to the Header and Jamb Tube. Only the Slide door breaks
out for emergency egress.
Section 2a: Parts of the Header
⑥
③
INDICATORS
61
6B
H
62
BA
GYRO TECH
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Do not disassemble the control box.
There are no user serviceable parts
inside.
FUNCTION [SLIDING DOOR]
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
Reduced Opening Switch
Mode Switch (see Mode SW Usage shown left)
Exterior Activation
Sequential Activation
Breakout Detector
Sidelite Presence Senso r
Contact Output (Class2 Load only)
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
Auxiliary Output (Open-Collector)
12VDC-(Common)
N/O
N/C
Common
SYMBOL No.
9DC12V 1
2
7
3
61
6B
4
5
H
6
M0
7
M1
62
8
SQ
9
10
BA
SLS
11
OUT.A 12
OUT.B 13
OUT.C 14
OUT
15
16
7
GYRO TECH
DS-150ＮＡ
（24-11327）
MADE IN JAPAN
1 12
11
7 0
98
To maintain warranty,repairs must be
made by authorized NABCO facilities.
⑧
HANDY TERMINAL･6P
Microprocessor Controller
248901-
10
O
5
A
M
P
I
POWER･2P
20VAC 50/60Hz
ERROR
No.
432
POWER
TB2
S1
Mode SW Usage
MODE
M0
M1
Open
Open
TWO WAY
Open
Gnd
ONE WAY
Gnd
Gnd
HOLD OPEN
Open
Gnd
NIGHT
RELATED DEVICES･16P
To protect against risk of fire or electric shock,use only the
certified NABCO power supply.
MOTOR･12P
TRANSFORMER
LABEL
ZNR1
TB1
WARNING
T1
⑦
765
NOISE
FILTER
ZNR2
⑤
④
>POM
<
②
①
⑩
DN 0369
1.
Power Cut Off Switch
N/A
6.
Belt Clip Assembly
4.
U30 Microprocessor Control
24-8901-30
9.
Anti Rise Roller
2.
3.
5.
DS 150/U30 Power Supply
Handy Terminal Harness
DS 150 Operator
Section 2b: Specifications
2-6
⑨
14-11741
12-13881
24-11327
7.
8.
Figure 4-1 Contents of Header
Timing Belt 3/4” wide
Idler Assembly
10. Hanger Roller
11-12805
14-0795
22-9210
11-9037
11-10733
Note:
Electrical conduit and switch or sensor wires should be pulled through the frame before mounting
the GT1175 System.
Note:
To prevent electrical interference for the 120 Vac Line, always route 120 Vac Power in from the end of
the header that is opposite to the controller and motor/operator. Refer to “Model GT 1175 Electrical
Installation Manual”; P/N 15-10596-30 for more information
Getting Started
1175 Standard Slide Door Installation Manual
Rev. 10-27-15
Part #15-9244-30
Table 2-1 Electrical Specifications
Electricity
Power Input
Available current for accessories
Available wire size for incoming power
Description
120 (±10%) AC 50-60Hz, 5 Amps
U Series Control 0.35 Amps 12 Volts DC
14 AWG
Section 2c: U30 Microprocessor Control
The U30 Microprocessor Control has been designed to control numerous operating characteristics
of the slide door system including speed, recycling sensitivity and reduced door opening width. It is
programmed after installation is complete. Please refer to the “U30 Microprocessor Control Setup and
Programming Manual”, P/N 15-9000-30 for detailed information.
Section 2d: Associated Manuals Part Numbers
►►“GT 1175 Standard Slide Doors Quick Setup Parts Guide” (P/N C-00105)
►►“GT 1175 Electrical Installation Manual **with U30 Microprocessor Controller” (P/N 15-10596-30)
►►“U30 Microprocessor Control Setup and Programming Manual” (P/N 15-9000-30)
►►“Automatic Sliding Door Owners Manual” (P/N 14-8907) for Decal Installation
►►“NABCO Price Book” for Sensors, Switches, and Accessories
Section 2e: Header Layout
►►Model GT 1175 Electrical Installation Manual ** with U30 Microprocessor Controller**
P/N 15-10596-30
Section 2f: Wiring
►►GT 1175 Electrical Installation Manual** with U30 Microprocessor Controller**
P/N 15-10596-30
Section 2g: Holding Beams
►►GT 1175 Electrical Installation Manual ** with U30 Microprocessor Controller**
P/N 15-10596-30
Section 2h: Electric Lock (Optional)
►►GT 1175 Electrical Installation Manual ** with U30 Microprocessor Controller**
P/N 15-10596-30
Section 2i: Troubleshooting
►►GT 1175 Electrical Installation Manual **with U30 Microprocessor Controller**
P/N 15-10596-30
►►U30 Microprocessor Control Setup and Programming Manual P/N 15-9000-30
Getting Started
2-7
Part #15-9244-30
Rev. 10-27-15
CHAPTER 3: ASSEMBLE FRAME
Section 3a: Prepare to Assemble Door Frame
1. Ensure the Rough Opening is correct size.
XX The width of the Rough Opening should equal: PACKAGE WIDTH
+ 1/4 INCH ON EACH SIDE
XX The height of the Rough Opening should equal: PACKAGE HEIGHT
+ 1/4 INCH
R.O. WIDTH
1/4”
90.0°
90.0°
R.O.
HEIGHT
DN 0081
Note:
FINISHED FLOOR
1/4”
1/4”
Figure 3-1 Masonry Opening
Make allowances for tile or other existing materials that may change the floor height.
2. Ensure the floor is level across the entire opening.
1-3/4”
Recess Threshold
Finished Floor
Jamb Tube
4-1/2”
Track
1/2”
DN 1110
Figure 3-2 Recessed Track
3. Place the Header on a flat surface. Remove (2) 8-32x0.625L Flat head screws used to secure the
removable Cover. Remove the Cover by lifting it up and then pulling it out.
Cover in
Closed Posion
DN 0393
3-8
8-32 x 5/8”
Phillips Head Screw
Swing
UP
to Open
Li UP to
Pull out
Figure 3-3 Remove Header Cover
Assemble Frame
Rev. 10-27-15
Part #15-9244-30
4. Unplug the Sensor (if equipped).
5. Remove Parts boxes and/or Parts bags from inside Header.
Section 3b: Assemble Door Frame (No Transom)
FOR DOOR FRAMES WITH A TRANSOM SKIP TO SECTION 3C
SINGLE
BIPART
DN 0768
1. Position Jamb Tubes on either side of Header according to the instruction sticker located on each
Jamb Tube, showing proper location and orientation. Ensure the removable cover side of Header is
facing up.
2. Orientate the Frame in relation to the building:
XX Fixed Sidelite: Removable Cover side of Header must face the Exterior side of building.
XX Full Open: Removable Cover side of Header must face the Interior side of building.
NOTE: Header diagrams shown with Access Cover removed.
FIXED SIDELITE UNITS:
Door
ACCESS COVER TYPICALLY
Opening
FACES THE EXTERIOR
Door
Opening
FULL OPEN UNITS:
FACES THE INTERIOR
DN 0394
Figure 3-4 Orientate the Door Frame in relation to the Building
3.b.a Secure Header to Slick Jamb Tubes
1. Secure the Header to each Jamb Tube with (6) 1/4-20 x .75 Whizlock screws.
a. If installed correctly there will be a 1/8 inch gap between the bottom of Header and the flat
surface.
Header
1/8” gap
Flat Surface
DN 1349
Assemble Frame
Slick
Jamb Tube
1/4-20 x .75” Whizlock Screw
Figure 3-5 Secure Header to Jamb Tubes
3-9
Part #15-9244-30
Rev. 10-27-15
Section 3c: Assemble Door Frame (with Transom)
FOR UNITS NOT INSTALLING A TRANSOM SKIP TO NEXT CHAPTER
The Transom is installed on top of the Header when glass windows (or panels) are needed above the Door
Unit. The Transom is used to frame glass windows or panels, with four parts:
XX Transom Horizontal:
•
Secured between the top of (2) Pocketed Jamb Tubes, and the top of Rough Opening.
•
•
Secured between the Transom Horizontal and the top of Header.
Used to divide where windows or panels are inserted into.
XX Transom Vertical:
XX Transom Clip:
•
Installed on the Header to secure Transom Verticals.
XX The Glass Stop Assembly:
•
A retaining strip mounted vertically or horizontally to hold glass windows or panels in place.
Transom Horizontal
Glass or Panel
Transom Vercal
Slide Door
Header
Jamb Tube
Fixed or Breakout Panel
DN 0688
Figure 3-6 Parts of Slide Door
1. Position Jamb Tubes on either side of Header according to the instruction sticker located on each
Jamb Tube, showing proper location and orientation.
a. Ensure the removable cover side of Header is facing up.
2. Orientate the Frame in relation to the building:
XX Fixed Sidelite: Removable Cover side of Header must face the Exterior side of building.
XX Full Open: Removable Cover side of Header must face the Interior side of building.
NOTE: Header diagrams shown with Access Cover removed.
FIXED SIDELITE UNITS:
FACES THE EXTERIOR
Door
Opening
Door
Opening
FULL OPEN UNITS:
FACES THE INTERIOR
DN 0661
3-10
Figure 3-7 Orientate the Door Frame in relation to the Building
Assemble Frame
Rev. 10-27-15
Part #15-9244-30
3.c.a Secure Transom Clips to Header
1. Locate pre-drilled holes on Header.
2. Secure Transom clips to Header with 10 x 1-3/4 inch Phillips Pan Head screws.
a. Please refer to the instruction sticker located on the Header for proper location and orientation.
b. Be sure to orientate all Transom Clips in relation to the Header cover.
Orientaon Scker
Vercal Transom Clip
10x1-3/4”
Pan Head Screw
Header Cover
Top of Header
HEADER COVER SIDE
DN 0419
Figure 3-8 Secure Transom Clips to Header
3.c.b Secure Header and Transom to Pocketed Jamb Tubes
Note:
1175 Slide Door Units installed with a Transom are shipped with Pocket Jamb Tubes only.
1. Place the Header between the Pocket Jamb Tubes so the removable cover side is facing up.
a. Ensure the Frame is still orientated in relation to the building.
2. Secure the Header to each Jamb Tube with (6) 1/4-20 x .75 Whizlock screws. If installed correctly there
will be a 1/8 inch gap between the bottom of Header and the flat surface.
1/8” gap
DN 0949
1/4-20 x .75”
Whizlock Screw
Pocketed
Jamb Tube
Flat Surface
Figure 3-9 Secure Header to Jamb Tubes
3. Slide and secure each Transom Vertical onto (1) Transom clip with 1/4-20 x 1” Flat Head screws.
4. Insert #8 x 1 inch Pan Head screws into each predrilled hole located on top of the Transom Horizontal.
5. Place the Transom Horizontal onto the Transom Verticals. Tighten each #8 x 1 inch Pan Head screw.
Assemble Frame
3-11
Part #15-9244-30
Rev. 10-27-15
#8 x 1”
Pan Head Screw
Transom
Vercal
1/4-20 x 1”
Flat Head Screws
Transom
Horizontal
Transom
Vercal
Header
Cover
Transom Clip
Header
Cover
DN 1151
Figure 3-10 Secure Transom Vertical to Transom Clip
6. Insert #8 x 1 inch Pan Head screws into each predrilled hole located on the outside face of each
Pocketed Jamb Tube.
7. Align the Transom Horizontal with the Jamb Tubes. Tighten each #8 x 1 inch Pan Head screw.
Jamb Tube
#8 x 1”
Pan Head Screw
Transom Horizontal
DN 0382
3.c.c Install the Tie Rods
Figure 3-11 Attach Horizontal Transom to Jamb Tubes
FOR TRANSOMS UNDER 11 FEET SKIP TO NEXT CHAPTER
Note:
Tie Rods are used for Transom Units that are 11 feet to 12 feet tall.
Note:
For units taller than 12 feet, please call Technical Support at 1-866-622-8325, for installation instructions.
1. Lift to position the assembled Frame into the rough opening.
2. Shim and Plumb Jamb Tubes in both planes to ensure the rough opening allows a 1/4 inch clearance.
3. Shim and plumb the Transom Horizontal at the top to ensure the rough opening allows a 1/4 inch
clearance.
Jamb Tube
DN 1348
1/4” Shim and plumb
for proper clearance
1/4”
Horizontal Transom
Figure 3-12 Shim and Plumb Frame
4. Go to the side of Header that is closest to the Exterior side of Door Opening,
3-12
Assemble Frame
Rev. 10-27-15
Part #15-9244-30
5. Mark the exact location of each Transom Vertical by drawing a horizontal line (the full width of
the Transom Vertical); along the outside edge of the Transom Horizontal; onto the ceiling of the
Rough Opening.
a. Do not draw the line wider than the Transom Vertical.
b. It is recommended to use a level for this step.
6. From the center of each Horizontal line, measure 1 inch deep (towards the interior side of building).
Mark a Vertical line onto the ceiling of the Rough Opening.
a. It is recommended to use a level for this step.
Mark Line
Exterior side of
Door Opening
3/8-16 Concrete Anchor
hole end of 1” mark
Measure 1” deep from
center of Horizontal Line
Ceiling
1”
DN 0411
Figure 3-13 Mark Transom Vertical Locations
7. Carefully remove the Door Frame from the Rough Opening. Set aside.
8. At the end of each Vertical Line mark, drill (1) 3/8-16 Concrete Anchor hole into the ceiling of the
Rough Opening,
9. Obtain all Tie Rods. (1) Tie Rod Parts box is shipped for each Transom Vertical.
10. Snap the Back Plate out from each Transom Vertical for easy access to the Tie Rod.
11. Transom Verticals are pocketed with (2) channels. Determine which channel is closest to the Exterior
side of Door Opening.
Channel closet to
Exterior side of Door Opening
DN 1350
Figure 3-14 Determine which Channel is closest to the Exterior Side of Door Opening
12. Insert (1) Tie Rod into that channel.
13. Insert each Tie Rod down into the 1 inch, pre-drilled hole located at the top of Header.
14. Once the Tie Rod is through the Header, loosely attach (1) Backing Plate, (1) 3/8 inch Washer, (1)
3/8 inch Lock Washer and (1) 3/8-16 Hex Nut (in that order) to the bottom of the Tie Rod.
a. The length of each Tie Rod equals the distance between the top of the Header and the top of the
Transom Horizontal, plus 2-5/8 inches.
Assemble Frame
3-13
Part #15-9244-30
Rev. 10-27-15
Concrete Anchor
Securely fasten Tie Rod to
Anchor with 3/4” minimum
thread engagement into
building structure
3/4” Min
Horizontal Transom Tube
Transom
Vercal
Tie Rod
Transom Vercal
Channel
Leg of
Roller Track
Back Plate
Top of Header
Header Cover
Backing Plate, 3/8” Flat Washer,
3/8” Lock Washer, and 3/8-16 Hex Nuts
Figure 3-15 Insert the Tie Rod
DN 1152
15. Allow each Tie Rod to rest on the Roller Track “Leg” within the Header.
a. The Tie Rod must remain inside the Transom Vertical until the Frame is fully secured into the
Rough Opening.Tie Rod Installation is completed after the Frame is installed.
Transom Horizontal
Tie Rod
Vercal Transom
(Mullion)
Top of
Header
DN 0404
Boom of Header
Figure 3-16 Rest Tie Rods on Roller Track
3-14
Assemble Frame
Rev. 10-27-15
Part #15-9244-30
CHAPTER 4: SECURE FRAME TO BUILDING
Section 4a: Secure door Frame to Building
1. Lift to position the assembled Frame into the rough opening.
2. Shim and Plumb Jamb Tubes in both planes to ensure the rough opening allows a 1/4 inch clearance.
Shim and plumb the Header or the Transom Horizontal at the top to ensure the rough opening allows
a 1/4 inch clearance.
Horizontal
Transom
Jamb Tube
1/4”
Header
DN 0760
Figure 4-1 Shim and Plumb Frame
4.a.a Anchor Placements
XX Anchors are not provided by NABCO.
XX Anchors must be appropriate for the type of structure being fastened to.
XX Screw in anchors to secure the Frame (per manufacturer’s specifications).
XX Ensure anchor heads do not come in contact with edges of glass to prevent breakage.
Note:
It is recommended to countersink holes as required to flush the surface.
Note:
It is recommended to drill tap threads for 1/4 inch anchors in a steel or aluminum structure.
Note:
Do not overtighten anchors to prevent deforming Jamb Tubes.
36”
48”
(914mm) (122mm)
max
max
Y
36”
48”
max
max
(914mm) (122mm)
Y
Y
Y
Y
Y
Y
Y
Y
Y
48”
max
max
XX Jamb Tubes
•
Y
Y
SLIDE DOOR
DN 0767
48”
(122mm)
(122mm)
SLIDE DOOR w/TRANSOM
Figure 4-2 Anchor Placement
Use 1/4 inch diameter anchors with a minimum of 3 per Jamb Tube, maximum is 48 inches on
center. Drill 1/4 inch diameter holes in the face of Jamb and then countersink each hole.
Secure Frame to Building
4-15
Part #15-9244-30
Rev. 10-27-15
POCKETED JAMB / VERTICAL TRANSOM
1/4” Anchor
1/4” Anchor Hole(s)
DN 0418
XX Transom Horizontal
•
•
SLICK JAMB
1/4” Anchor
1/4” Anchor Hole(s)
Figure 4-3 Screw Anchors
Use 1/4 inch diameter anchors with a minimum of 3 per Transom tube, maximum is 48 inches on
center. Anchoring is required within 8 inches of all vertical mullions.
Drill 1/4 inch diameter holes in the face of Transom Horizontal and then countersink each hole.
XX Header
•
To prevent Header sag, use 1/4 inch diameter anchors or 3/8 inch threaded rods, with a
maximum 48 inches on center. First anchor maximum is 36 inches from each end of the Header.
Drill 1/4 inch diameter holes inside the top of Header.
Section 4b: Complete the Tie Rod Installation (For Transom Units only)
1. After the Frame has been installed, slide each Tie Rod up the Channel into each 3/8-16 Anchor
located in the ceiling.
a. The 3/8-16 Anchor is used to securely fasten the Frame.
2. Go to the bottom of each Tie Rod. Tighten the 3/8-16 Hex Nut and 3/8 inch Lock Washer to secure
the Backing Plate.
3. Snap the Back Plate back into each Transom Vertical.
a. It may be necessary to use a rubber mallet to slightly tap the Back Plate into place.
b. Protect the surface of the Back Plate before hitting it with a rubber mallet.
4-16
Secure Frame to Building
Rev. 10-27-15
Part #15-9244-30
CHAPTER 5: 120 VAC GENERAL WIRING
WARNING
Shut the installation site, branch Circuit Breaker OFF. Failure to do so may result
in serious personal or fatal injury. When uncertain whether power supply is
disconnected, always verify using a voltmeter
WARNING
All high voltage electrical connections must be made by licensed electricians
according to National and Local electrical codes/regulations.
CAUTION
Permanent wiring shall be employed as required by local codes.
CAUTION
Keep all Incoming 120 VAC wiring separate from low voltage wiring within Header. 120
VAC Power wires must be routed (separate from other wiring) located near the top of
inside Header.
CAUTION
Ensure that the Grounding of the Electric Power Supply is installed/connected in a
proper way (especially the PE Cable from the Building Side).
Attention: Insert all Incoming 120 VAC Power wires into the pre drilled Electric Service Access Hole located
at the left or right side of Header End Cap.
BC
DS-1500
D24-113270
Nabtesco Corporation
N
32
4
1211
0
8
7 6 5
Auxiliary 120 VAC Power wires
1
7
10 9
L
120 VAC General Wiring
T1
(These wires normally coiled and ed up)
H
M0
Open
Gnd
Gnd
Open
Mode SW Usage
MODE
M1
Open
TWO WAY
Open
ONE WAY
Gnd HOLD OPEN
Gnd
NIGHT
! CAUTION
62
ERROR
PE
AC 115V ± 10%
50 / 60 Hz
GYRO TECH
6B
BA
MADEI N JAPAN
To protect against risk of fire
or electric shock,use only the
!
NABC O
61
GYR O TECH
TB2
TB1
NOISE
FILTER
MOTOR･12P
POWER
INDICATORS
PRESS
TO
RESET
O
NA
NAB CO
LOAD
RED INDICATES
POWER IS OFF
! WARNING
NABCO
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
-CIRCUIT-BREAKER-
POWER･2P
20VAC 50/60Hz
S1
Motor/Operator
P/N M-00395
P/N V-00020
!
inside.
!
HANDY TERMINAL･6P
No.
248901FUNCTION [SLIDING DOOR]
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
Exterior Activation
Breakout Detector
Sidelite Presence Sensor
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
On/Off
Power Switch Power Supply
P/N V-00029
<
Ground Wire
It is recommended for the Installer to house all Incoming 120 VAC wires within an Electrical
Conduit.
>PO
M
Note:
120 VAC
DN 0647
5-17
Part #15-9244-30
Rev. 10-27-15
CHAPTER 6: WIRE THE SWITCH ASSEMBLY
Note:
Do not secure the Switch Assembly to the Jamb Tube until after the Slide door installation is complete.
Note:
The U30 Microprocessor Control, Main Harness comes in three lengths: 36 inches, 72 inches, and 80
inches. The length used is dependant upon the type of installation.
Note:
The Rocker Switch and the Key Switch are both installed the same way.
1. Go inside the Header. Locate the Pin wiring that is attached to the Main Harness.
2. Draw the Pin wiring through a hole located at the side of Header and Jamb Tube. Continue to route
down the Jamb Tube.
3. Pull the Pin Wiring through the cut out.
4. Obtain (1) loose 5 Circuit Pin Housing from the Parts Box.
5. Insert each Pin into the 5 Circuit Pin Housing accordingly:
a. 1 = Red, 2 = Orange, 3 = Blue, 4 = Green, 5 = Orange
6. Connect the Switch Harness from the back of the Switch Assembly to the Main Harness.
a. Place extra wiring back inside the Jamb Tube.
7. Insert the Switch Assembly into the Cut Out.
8. Secure the Switch Assembly to the Jamb Tube with (2) 10-32 x 1/2 inch Phillips Head Screws.
Header Plate
Wire Access Hole
Jamb Tube
Wire Access Hole
Female Pin Wiring
Key Switch
Male Pin
Housing
DN 1002
6-18
Rocker Switch
Red
Orange/White
Blue
Green
Orange
1
2
3
4
5
Female Pin
Housing
Figure 6-1 Secure the Switch Assembly to the Jamb Tube
Wire the Switch Assembly
Rev. 10-27-15
Part #15-9244-30
CHAPTER 7: LAY DOWN THE THRESHOLD (Optional)
FOR UNITS NOT INSTALLING A THRESHOLD
SKIP TO CHAPTER 8
Note:
Do Not permanently secure the Surface Threshold until the Slide Door has been installed. Doing so
may cause misalignment.
Note:
Thresholds are factory cut to be the same width as the door opening. However, extending the
Threshold across the entire door opening is optional. To order additional track, please contact
customer service at (877) 622-2694.
Standard Thresholds vary in width and can be installed two different ways:
XX Recessed: Installed into the floor (1/2 inch deep) across the full length of the track.
XX Surface: Installed on the surface of the floor with ramps attached to both sides.
RECESSED TRACK
4 ”
Bumpers
DN 0087
SURFACE TRACK
7”
Bumpers
Figure 7-1 Recessed vs Surface Track
Attention: The Threshold must be laid down so the Channels are located on the side of Slide Door.
BUMPERS
(Used to Cushion Boom Guide Prongs)
Jamb Tube
FILLER INSERTS
Sidelite
(Used to Fill In areas
Boom Guide does not slide within)
Threshold
(Channels installed on side of Slide Door)
Bumpers
DN 1369
Jamb Tube
Filler Inserts
7.1 Install the Surface Threshold
Figure 7-2 Lay down Threshold Correctly
1. Obtain the Surface Threshold.
2. Snap a chalk line on the floor from Jamb to Jamb.
XX Full Open: On the Exterior side
XX Fixed Sidelite: On the Interior side
Lay Down the Threshold
7-19
Part #15-9244-30
Rev. 10-27-15
FULL OPEN
Jamb Tube
EXTERIOR
Chalk Line
DN 1027
FIXED SIDELITE
Jamb Tube
3. Position the Threshold until the full length is flush with the chalk line.
Chalk Line
Figure 7-3 Snap Chalk Line
4. Hang a Plumb Bob from the Header.
5. Ensure the outside edge of the Threshold is 1/8 inch from the Plumb line.
Header
Header
6-1/2”
Plumb Line + 1/8”to edge of track.
Jamb Tube
6-1/2”
(not Pocketed)
6-3/8”
4-1/2”
1/8”
Pocketed
Jamb Tube
4-1/2” Track
6-3/8” Track
1/8”
DN 0090
6. Locate (2) screw splines on each end (exposed side) of the Threshold.
Figure 7-4 Plumb Line
7. Secure (1) Threshold End Cap to each screw spline with (2) 6 x 3/8 inch Phillips Head screws.
a. Use a 1/8 inch diameter drill bit to make the screw spline bigger if the Threshold End Cap can not
be properly secured with the screws provided.
Standard Floor Track
6 x 3/8” Phillips Head Screw
Screw Spline
Standard Threshold End Cap
Figure 7-5 Secure Threshold Cap to Threshold
DN 0091
8. Permanently secure the Surface Threshold after Slide Doors are completely installed.
7.2 Recessed Threshold
1. Snap a chalk line on the floor from Jamb to Jamb on both sides.
2. Create a channel that is 1/2 inch deep, full width of Jamb Tubes, and full length of Threshold.
3. Place the Threshold inside the channel so the full length is flush with the chalk line.
Floor Surface
Track
1/2”
DN 0761
7-20
Figure 7-6 Track Recess
Lay Down the Threshold
Rev. 10-29-15
Part #15-9244-30
CHAPTER 8: INSTALL THE SIDELITE
There are (2) Sidelite Configurations:
XX Full Open: The Swing Sidelite has breakout capabilities. Both the Swing Sidelite and Slide door must
breakout at the same time.
XX Fixed Sidelite: The Fixed Sidelite does not have breakout capabilities. Only the Slide door can breakout.
FULL OPEN
FIXED SIDELITE
Fixed Sidelite or
Wall Track
Swing Sidelite
Slide Door
DN 0762
Figure 8-1 Sidelite Configurations
Section 8a: Full Open Sidelite
FOR FIXED SIDELITE UNITS SKIP TO SUBSECTION 8.B
8.a.a Install the Bottom Pivot
1. Go to the bottom of the Pivot Jamb Tube. Insert the Bottom Pivot into the hole.
2. Secure the Bottom Pivot to the Pivot Jamb Tube with (1) 1/4-20 x 1/2 inch Phillips Head screw.
3. Go to the screw hole located in front of the Barrel.
4. Secure the Floor Pivot to the Threshold with (1) 1/4-20 x 1/2 inch Phillips Head Screw.
5. Insert (1) 1/4 x 2-3/4 inch Phillips Head Screw inside the Barrel. Tighten.
6. Cap the Barrel with (1) Bushing.
Boom Pivot
1/4-20 x 1/2”
Phillips Head Screw
DN 1045
8.a.b Partially Install the Limit Arm
1/4-20 x 1/2”
Phillips Head Screw
1/4 x 2-3/4”
Tapcon Screw
Bushing
Figure 8-2 Temporarily Secure Bottom Bracket to Jamb Tube
1. Slide (1) .255 ID x .900 OD x .125 THK Nylon Washer onto (1) 1/4-20 x 1 inch Phillips Head Screw.
2. Go underneath the Limit Arm. Insert the Washer and Screw up into the screw hole.
3. Go to the pre-drilled screw hole located at the bottom of Header (on the Pivot Side of Sidelite).
Install the Sidelite
8-21
Part #15-9244-30
Rev. 10-29-15
4. Secure the Limit Arm to the Header by tightening the Screw.
a. Loosely tighten (just enough to keep the Screw assembly from falling out of the hole).
b. Limit Arm installation is completed after the Swing Sidelite is fully installed.
Limit Arm
Limit Arm Wheel
.255 x .900 x .125 THK
Nylon Washer
1/4-20 x 1”
Phillips Head Screw
DN 0771
Boom of Header
Pivot Hole
Figure 8-3 Partially Install the Limit Arm
8.a.c Install the Full Open Sidelite onto the Upper Pivot and Bottom Pivot
1. Locate the Bottom Pivot inside the Pivot Stile (at the bottom). Insert the Bottom Pivot into the Floor
Pivot Barrel.
Jamb Tube
Barrel
DN 1046
Boom Pivot
Figure 8-4 Position the Swing Sidelite Panel over the Bottom Pivot at 90° angle
2. Go to the Top Pivot that is preinstalled inside the Pivot Stile. Push the Top Pivot down by pressing on
the Spring Pin.
3. Align the Top Pivot with the Pivot Hole located at the bottom of Header.
4. Release the Spring Pin to allow the Top Pivot to snap up into the hole. Ensure the Top Pivot fully
engages the hole.
a. If necessary, use a flathead screwdriver to lift up on the Spring pin until the Pivot Pin is fully
seated within the hole.
b. Ensure not to pinch Cable Wiring.
Cable Wiring from
Main Harness (Inside Header)
Top Pivot
Pivot Sle
Hole
Spring Pin
8-22
Break Out
Direcon
Spring Pin
DN 0705
Figure 8-5 Insert Top Pivot into Header
Rev. 10-29-15
Part #15-9244-30
8.a.d Complete Installation of the Limit Arm
1. Swing open the Swing Sidelite 90 degrees. Align and then rest the Limit Arm inside the Top Rail.
2. Open the Swing Sidelite all the way. Tighten (1) 1/4-20 x 1 inch Phillips Head screw to secure the
Limit Arm to the Header.
8.a.e Adjust the Ball Detents
Note:
Breakout resistance for Ball Detents must meet ANSI Standard A156.10 or Local Codes.
1. Go to the top of the Strike Stile. With a 15/16” Open End wrench, loosen the Nut to raise or lower the
Ball Detent so it has light contact with the Bottom of Header.
2. Open and close the Swing Door several times to score the surface on the Bottom of Header locate and
mark where the Score intersects the center groove.
3. With a 1/4 inch drill bit, drill a screw hole through the Bottom of Header. Countersink the screw hole
3/8 inch x 82°.
Ball Dentent
Drilled and Countersunk Hole
Nut
Score Mark
Top of Strike Sle
DN 0764
90°
Figure 8-6 Adjust the Ball Dentent on top of Strike Stile
4. Go to the bottom of the Strike Stile. With a 15/16” Open End wrench, loosen the Nut to raise or lower
the Ball Detent so it has light contact with the Threshold.
5. Open and close the Swing Door several times to score the surface on the Threshold. Locate and mark
where the Score intersects the center groove.
6. With a 1/4 inch diameter drill bit, drill a hole through the Threshold (Just deep enough for the Ball
Dentent to fit within). Countersink the screw hole to be 1/4 inch x 82°.
90°
Drilled and
Countersunk Hole
Boom Rail
Nut
Ball Dentent
Score Mark
Figure 8-7 Adjust the Ball Dentent on bottom of Strike Stile
DN 0765
7. Close and then break open the Swing door to test fit for both Ball Detents.
a. To adjust the fit, increase the size of the hole and countersink.
b. Do Not over-drill the hole. If hole is overdrilled the Threshold will need to be replaced.
c. For additional travel remove the Ball Detent Bracket to lower or raise the Ball Detent.
8-23
Part #15-9244-30
Rev. 10-29-15
8.b Fixed Sidelite
8.b.a Secure the Fixed Sidelite to the Door Frame
1. Locate (1) cut out at the top of Strike Stile. Align and then slide the Fixed Sidelite until (1) mounting
bracket (preinstalled under the Bottom Lip of Header) can be seated inside the Cut Out.
Cut Out
Strike Sle
Mounng Bracket
DN 0862
Figure 8-8 Slide Mounting Bracket into Cut Out
2. Locate (2) Cut Outs on the side of the Pivot Stile. Align and then slide the Fixed Sidelite until (2)
Mounting Brackets (preinstalled on the Pivot Jamb Tube) can be seated inside each Cut Out.
3. Slide the Fixed Sidelite towards the Interior of the Building until both Mounting Brackets butt up
against the inside wall of the Pivot Stile.
1/4-20 x 1/2”
FlatHead Screw
Header Mounng Bracket
(Inside Vercal Mullion)
Cutout Clearance
1/4-20 x 1/2”
Flat Head Screw
Jamb Tube Mounng Bracket
Jamb Tube
Mounng Bracket
DN 0863
Figure 8-9 Slide Mounting Block into Top Rail
4. Snap a chalk line between Jamb Tubes in front of Sidelite Panel. If the Sidelite Panel runs parallel to
chalk line, it is square.
5. Secure the Fixed Sidelite Panel to all (3) Mounting Brackets with 1/4-20 x 1/2 inch Flat Head Screws.
Jamb Tube
DN 0624
Chalk Line
Jamb Tube
Fixed Panel
Figure 8-10 Ensure Fixed Panel is Square
8.b.b Insert the Bottom Guide Double Roller Assembly under the Strike Stile
1. Go to the bottom of Strike Stile. Remove the Bottom Guide Cover Plate. Set aside.
8-24
Rev. 10-29-15
Part #15-9244-30
Boom Guide
Cover Plate
1/4-20 x 3/4”
Phillips Screw
DN 0128
Figure 8-11 Remove Bottom Guide Cover
2. Install the Bottom Guide Double Roller Assembly by sliding (2) rollers into the Bottom Rail so the
Bracket sticks out from underneath (in direction of where the Slide door is to be installed).
3. Use the Bracket to slide the Bottom Guide Double Roller Assembly towards the Pivot Stile.
Boom Guide Assembly
Boom Rail
Floor
DN 0865
8.b.c Install the Floor Bracket
Figure 8-12 Slide Bottom Guide Assembly into Bottom Rail
1. Go to the bottom of the Strike Stile. Insert the Floor Bracket inside the Bottom Rail so the bottom
plate portion sticks out from underneath (in direction of where the Slide door is to be installed).
2. Close the Slide Door. Adjust the Fixed Panel for weathering gap. Adjust the Slide Door for rocking.
3. Secure the upper plate portion of the Floor Bracket to the side of Strike Stile with (1) 1/4-20 x 1/2
inch Phillips Head screw.
4. Use the Floor Bracket as a template to drill (2) screw holes for #14 x 1-1/4 inch Flathead Tapcon
screws.
5. Secure the Floor Bracket to the floor with (2) #14 x 1-1/4 inch Flathead Tapcon screws. Replace the
Cover Plate.
Boom Rail
1/4 x 1-1/4”
Tapcon Screw
Strike Sle
1/4-20x1/2”
Phillips Head Screw
DN 0864
Floor Bracket
Figure 8-13 Install Bottom Bracket
8-25
Part #15-9244-30
Rev. 10-27-15
CHAPTER 9: INSTALL THE SLIDE DOOR
9.a Secure the Slide Door Carrier to Belt Clips
CAUTION
Do not test Breakout until all adjustments are made and doors are secured.
1. Cover the Sidelite Panel with cardboard on the side that will face the Slide door.
An-Rise Roller
Carrier
Hanger Roller
Nut
DN 1043
CAUTION
Figure 10-1 Carrier with Rollers
Do not rotate the Roller Axle counter-clockwise. Doing so will unthread the Axle from
the Roller Assembly.
2. Go to the Carrier on top of Slide Door. Loosen (1) 7/16-20 Whiz Lock Nut on each Roller by inserting (1)
7/32” Allen wrench into the exposed end of a Roller Axle. Hold the 7/32 inch Allen wrench in place to
keep the Roller Axle stationary. At the same time, loosen (1) 7/16-20 Whiz Lock nut with a 15/16 inch
Open End Wrench.
An-Rise Roller
Hanger Roller
Nut
End of Roller Axle
DN 1028
Figure 10-2 Loosen Nuts
3. Lift and then slightly tilt the Slide door to place all (4) Rollers onto the track (located inside the Header).
Track
Roller
Carrier
DN 0779
9-26
Figure 10-3 Install Carrier onto Track
Install the Slide Door
Rev. 10-27-15
Part #15-9244-30
4. Secure the Belt Clip to the Carrier with (2) 1/4-20 x 3/4 inch Whiz-Lock screws.
a. Long Belt Clips are installed on Single Slide Door Units or Lead Slide Doors for Simultanuous Pair
Units.
b. Short Belt Clips are installed on Trail Doors for Simultanuous Pair Units; to the left side of Carrier.
LEAD DOORS AND TRAIL DOORS ARE ONLY
INSTALLED ON SIMULTANUOUS PAIR UNITS
Long Belt Clip
used for Single
Slide Door and
Lead Door
Carrier
Short Belt Clip
used for Trail Doors
1/4”-20 x 3/4”
Whiz-Lock Screw
DN 0720
Figure 10-4 Secure Belt Clips to Carrier
9.b Install Bottom Guides
9.b.a Insert Bottom Guide into the Threshold (Full Open Sidelite)
FOR FIXED SIDELITE UNITS SKIP TO SUBSUBSECTION 9.B.B
1. Locate the Bottom Guide Assembly that was preinstalled inside the Slide Door Strike Stile.
2. Lift up the Prongs until the Bottom Guide is directly above the Guide Channels. Drop the Prongs into
the Guide Channels.
Li Up
Boom Guide; Prongs
Guide Channels
DN 0894
Figure 10-5 Drop Prongs into Channel Guides
9.b.b Secure the Bottom Guide Double Roller Assembly to the Slide Door (Fixed Sidelite)
FOR FULL OPEN UNITS SKIP TO SUBSECTION 9.C
1. Go to the Bottom Rail of Fixed Sidelite.
2. Locate the Bottom Guide Double Roller Assembly.
a. The Bracket will be sticking out from underneath.
Fixed Sidelite
DN 0640
Slide Door
Washer
1/4 - 20 x 3/4” Whiz-Lock Screw
Figure 10-6 Install Sliding door to Bottom Guide Assembly
9-27
Part #15-9244-30
Rev. 10-27-15
3. Slide the Slide Door’s Pivot Stile onto the Bracket.
4. Support the weight of the Fixed Sidelite.
5. Breakout the Slide door to Full Open position.
6. Secure the Bracket to the Pivot Stile with (2) 1/4 - 20 x 3/4 inch Whiz-Lock screws.
9.c Adjust the Rollers
9.c.a Hanger Rollers
1. Raise or lower the Slide door by turning the Axle clockwise with a 15/16” Open End Wrench.
a. The appropriate gap between the Bottom Rail and floor is between 11/16 inch to 15/16 inch;
with the nominal gap being 7/8 inch.
Hanger Roller
55mm An-Rise Rollers
Hanger Roller
Hanger Roller Centers must be to the
RIGHT of their bolts.
DN 1044
Figure 10-7 Door Adjustment
2. Ensure the Leading Edge of the Slide door and (other Slide door or Jamb Tube) are parallel.
3. Ensure the Leading Edge of the Slide door and Header are parallel.
4. Tighten the 7/16-20 Whizlock nuts. Do not overtighten.
Parallel Gap
Parallel Gap
Parallel Gap
Parallel Gap
Parallel Gap
DN 0895
BIPART
11/16” (17mm) to
15/16” (24mm);
7/8” (22mm)
nominal
9.c.b Anti Rise Rollers
SINGLE
Figure 10-8 Floor Gap
1. Loosen (2) Anti-Rise Rollers located towards the middle of the Carrier.
2. Slide the Anti-Rise Roller up or down within the slot until there is 1/64 inch to 1/32 inch gap
between the Roller Wheel and the Top Track. Gap should be about the same thickness as a credit card.
9-28
3. Tighten the 7/16-20 Whizlock nuts. Do not overtighten.
Rev. 10-27-15
Part #15-9244-30
An-Rise Track
1/64 inch to
1/32 inch
clearance
Insert 7/32” Allen Wrench
Slide An-Rise Roller up in slot unl
a 1/64 inch to 1/32 inch clearance
is between the An-Riser Wheel
and the An-Riser Track.
9.d Adjust the Interlocks
DN 0633
Figure 10-9 Wheel and Track Clearance
1. Manually close the Slide Door. Ensure the Interlocks are properly engaged. If not, adjust the
Interlocks.
DN 1051
Interlock
Correctly Engaged
Interlock
NOT Correctly Engaged
Figure 10-10 Close Door to Adjust Interlocks
9.d.a Adjust the Interlock
Note: Adjust Interlocks so there is no contact between the Rail and the Interlock. Any contact will cause the
Slide Door to bind.
1. Obtain (1) parts bag containing (4) Shims that was taped to the Slide Door at the NABCO factory.
2. Remove the Interlock on the Sidelite, Strike Stile.
3. Place (1+) shims directly underneath the Interlock. Line up the screw holes.
4. Secure the Interlock assembly to the Sidelite Strike Stile with (2) #10-32 x 5/8 inch Phillips Head
Screws.
a. Loosely tighten the mounting screws just enough to keep the Interlock assembly from falling out
of place.
Sle
Shim
Interlock
#10-32 x 5/8”
Phillips Head Screw
DN 0745
Figure 10-11 Place (1+) Shim under Interlock
5. Go to the Interlock located on the Pivot Stile of the Slide Door. Loosen the mounting screws.
6. Manually close the Slide Door. The loosened Interlocks will automatically adjust to proper position.
7. Lock the Interlock and 1+ Shim in place by tightening the #10-32 x 5/8 inch Phillips Head Screws.
9-29
Part #15-9244-30
Rev. 10-27-15
Section 9e: Permanently install the Threshold
1. Go to each end of Threshold. Mark (1) drill hole approximately 4” from each edge.
2. Mark remaining drill holes to be evenly spaced.
Drill Screw Holes in Metal Strip
Figure 10-12 Mark and Drill Holes on Threshold
DN 1047
3. With a 1/4 inch masonry drill bit, drill through the Threshold and into the floor no less than 1-1/2
inch deep.
4. Secure the Threshold with Fasteners not provided by NABCO.
Section 9f: Threshold Maintenance
1. Check for wear of Bottom Guide Roller and Bumpers inserted within Threshold Channels.
2. Listen for squeaking/grinding noise.
3. Look for dirt/debris/excessive build-up. If dirt/debris/excessive build-up is found.
1. Vacuum to remove loose material.
2. Wipe off the Threshold.
3. Use (1) slotted Screw Driver to remove dirt/debris and/or excessive build–up located within Threshold
Channels.
4. Inspect weekly and daily during winter as snow and ice can build up.
Fastener not provide by NABCO
Metal Strip
Flat Surface
DN 1048
9-30
Figure 10-13 Secure Threshold to Flat Surface
Rev. 10-27-15
Part #15-9244-30
CHAPTER 10: INSTALL THE WEATHERING
FIXED SIDELITE
Roller Assembly
FULL OPEN
Boom Guide
Slide Door
Weathering
1/8”
Swing Sidelite
BREAKOUT SIDE
Weathering
Figure 10-1 Weathering Placement
Slide Door
Weathering
DN 0119
1. Install Brush by sliding it into the Brush Holder:
►►Fixed Sidelite
1. Secure the Brush Holder against the Bottom Rail of Slide door with (3) #6 x 1/2 inch self
tapping screws.
►►Full Open
1. Secure the Brush Holder against the Bottom Rail of Swing Sidelite with (3) #6 x 1/2 inch self
tapping screws.
a. It is recommended to leave at least a 1/8 inch gap between the Edge of the Pivot Stile and
the Brush Holder, while allowing 1/8 inch Vinyl to extend past the Brush Holder so the gap
is filled.
2. Breakout the Swing Sidelite. Secure the Brush Holder against the Bottom Rail of Slide door
with (3) #6 x 1/2 inch self tapping screws.
Section 10a: Apply Caulking Bead
1. Ensure the entire Door Frame is properly secured to the Rough Opening.
2. Apply caulking bead between the Door Frame and Rough Opening (inside and outside).
3. Apply caulking bead to the Threshold at the bottom of Door Frame.
Caulk the top and both sides
of Door Frame
DN 0883
Install the Weathering
Caulk the Threshold
10-31
Part #15-9244-30
Rev. 10-27-15
CHAPTER 11: INSTALL THE GLASS STOPS
Glazer must be fully trained and qualified. Failure to do so may result in bodily injury, or
property damage.
WARNING
Note: Ensure the installation area is free of debris and/or sharp objects. Failure to do so may damage the
glass or contaminate the glazing process.
Section 11a: Door Panel
Note: The Snap Base and Vinyl Seals/Gaskets are preinstalled at the NABCO Factory.
1. Ensure the Snap Base is free of debris and/or sharp objects.
2. Install the Setting Blocks (not provided by NABCO) and Glass Panel.
3. Snap the Glass Stop into the Snap Base.
1/4” (6mm)
Glass Stop
Seng Block
Glass Panel
Vinyl Bumper
1/4” (6mm)
Snap Base
DN 1031
Section 11b: Transom
Figure 11-1 Door Panel Glass Stop
Note: Vinyl Bumpers are preinstalled at the NABCO Factory.
1. At the top of Header, snap each Snap Base inside the Channel on either side of Vertical Transoms.
XX Full Open Doors:
•
•
Install the Snap Base on the Exterior Side of the Building.
Removable Cover faces Interior Side of the Building.
XX Fixed Sidelite Doors:
•
•
Install the Snap Base on the Exterior Side of the Building.
Removable Cover faces the Exterior Side of the Building.
2. Install the Setting Blocks (not provided by NABCO) and Glass Panel.
3. Snap (1) Glass Stop into each Snap Base.
11-32
Install the Glass Stops
Rev. 10-27-15
Part #15-9244-30
1/4” (6mm)
Snap Base
1/4” (6mm)
Glass Stop
FIXED SIDELITE SLIDE DOOR UNIT
(Removable Cover on Exterior Side)
1/4” (6mm)
Glass Stop
Channel
1/4” (6mm)
Snap Base
Channel
FULL OPEN SLIDE DOOR UNIT
(Removable Cover on Interior Side)
DN 1032
Section 11c: Dust Protector Hoods (Clean Room)
Figure 11-2 Transom Glass Stops
Note: All Aluminum Hoods and Vinyl Shields are installed for Clean Room Slide Door Units only and are not
manufactured by NABCO. Please call Customer Service for replacement parts at 1-888-679-3319.
11.c.a Door Panel and Transom
Note: Aluminum Hoods are installed at the bottom of each Door panel and Transom.
1. Install Glass Stops according to Subsection 14.1 and Subsection 14.2.
2. Place each Aluminum Hood over each Glass Stop so the bottom edge of the Aluminum Hood is resting
on the surface.
a. Do Not remove protective paper from double sided Cladding Tape at this time.
3. Insert the bottom half of each Vinyl Strip inside the gap that is located behind the Aluminum Hood.
The Vinyl Flap must be laying on top the Aluminum Hood.
4. Hold the assembly in place while it is pressed up against the Glass Panel. Make a temporary Mark
along the full length of the Vinyl Strip.
a. Ensure the bottom edge of the Aluminum Hood is still resting on the surface for proper
alignment.
5. Remove the assembly.
6. Remove the protective paper to expose the Cladding Tape from the Vinyl Shield.
7. Align the Vinyl Strip to the temporary Mark and adhere to the Glass Panel.
8. Remove the protective paper to expose the Cladding Tape from the Aluminum Hood.
1. Align the Aluminum Hood with the Vinyl Shield.
2. Adhere the Aluminum Hood to the Glass Stop and tuck it under the Vinyl Flap.
11-33
Part #15-9244-30
Rev. 10-27-15
Glass Panel
Tuck Aluminum Hood
under Vinyl Shield
Adhere Vinyl Shield
along Mark Line
Mark Line
Vinyl Shield
Gap
Adhere Aluminum Hood
to Glass Stop
Surface
Aluminum Hood
DN 1033
Inside Face
Aluminum Hood
Cladding Tape
Vinyl Flap
Cladding Tape
Assembly
Vinyl Shield
Figure 11-3 Install Dust Protector Hoods for Door Panels and Transoms
11.c.b Header
1. Go to the side of Header that has the Removable Cover.
2. Position the Stainless Steel Hood on top of the Header so the (turned under) bottom lip is resting on
the Header surface and the inside face is pressed up against the building.
a. Ensure proper length and fit is correct.
3. Remove all protective paper to expose the Cladding tape.
4. Adhere the Stainless Steel Hood to the Header.
3/8”
Dust Protector Hood
Building
45
DN 1034
1/2”
Header
Figure 11-4 Install Dust Protector Hoods for Header
11-34
Rev. 10-27-15
Part #15-9244-30
CHAPTER 12: ADJUSTMENTS
Section 12a: Adjust Preload
1. Support the weight of Slide Door, then Breakout Slide door approximately 5 degrees (just enough to
expose the Preload Adjustment Screw located on back edge of door). Do not let Slide door push up
against any other Door Panel.
2. Check for door sag. The Slide door should latch without having to be manually lifted.
Preload Adjustment Screw
Pivot bar
Carrier
Door Sag
Pivot Block
Preload Adjust
DN 0726
Figure 12-1 Check Door Sag
3. Go to the Preload Block located inside Top Rail. Loosen (2) Locking Bolts.
4. Go to the back edge of Pivot Stile. Reduce Door sag by tightening the 5/8 inch Set Screw with an 7/32
inch Allen Wrench. Do Not allow the Adjustment Set Screw to protrude more than 7/32 inch past the
end of stile.
a. If deemed necessary, substitute the 5/8 inch Set Screw with the optional 1/2 inch Set Screw
supplied by NABCO.
5/16” Adjustment Set Screw
Preload Block
(If needed: use oponal 1/2” Set
Screw provided by NABCO)
DN 0727
12.a.a Correct Preload Misalignment
Locking Bolts
Limit Arm
Figure 12-2 Adjust the Preload
1. Break Open the Slide Door. Locate the Carrier Pivot Assembly inside the Top Door Web.
2. Loosen the 5/16-24 x 1/2 Set Screw located on the Pivot Stile at the Top.
3. Loosen (2) 1/4-20 x 1.75 Hex Screws used to secure the Carrier Pivot Assembly to the Top Door Web.
4. Slide the Carrier Bar to the left or right, until the Slide Door is aligned to the Carrier.
5. Tighten all screws.
12-35
Part #15-9244-30
Rev. 10-27-15
1/4-20 x 1-3/4”
Hex Screw
Carrier and Door
Misaligned aer
adjusng preload
Pivot
Carrier
Misaligned
5/16-24 x 1/2”
Set Screw
DN 0741
Figure 12-3 Correct Preload Misalignment
6. Verify that the Lower Panic Catch inside the Door Web is still aligned to the Upper Panic Catch inside
the Carrier. If an adjustment is necessary:
1. Go to the Lower Panic Catch. Loosen (2) 1/4-20 X 1-1/4 inch Socket Screws used to to secure the
Lower Panic Catch to the Door Web.
2. Slide the Lower Panic Catch to the right or to the left until it is aligned to the Upper Panic Catch.
Tighten Socket Screws.
1/4”-20 x 1-3/4” Socket Screw
Lower Panic Catch Assembly
DN 1368
12.a.b Adjust the Ball Plunger
Figure 12-4 Align the Lower Panic Catch to the Upper Panic Catch
1. Breakout the Slide door. Go inside the Top Rail (closest to the Strike Stile). Remove the Panic
Catch Assembly.
1/4-20 x 1-1/4”
Socket Screw
Panic Catch
Loosen the Set Screw
2. Loosen the Set screw that is located in front of the Panic Catch.
Ball Plunger
DN 0122
Figure 12-5 Panic Adjustment
3. Go underneath the Panic Catch. Raise or lower the Ball Plunger to adjust the engagement.
a. The Ball Plunger must be adjusted for proper breakout resistance to meet ANSI A156.10 code
and/or local code.
b. Use minimal engagement if Panic Hardware is used.
4. Tighten the Set screw. Secure the Panic Catch Asssembly inside the Top Rail with (2) 1/4-20 x 1-1/4
inch Socket Head screws.
12-36
Rev. 10-27-15
Part #15-9244-30
12.a.c Adjust the Breakout Magnet
1. The Magnet is secured to the Limit Arm Bracket that can slide to the Left and Right. Slide the Breakout
Magnet to the Left or to the Right until it is aligned with the Magnetic Reed Switch.
a. The Magnetic Reed Switch is a 3/8 inch diameter black circle located on the Bottom Lip of Header.
Magnet
Magnet
Boom Lip
of Header
Magnec
Reed Switch
DN 0781
Breakout Slide Door
Figure 12-6 Breakout Magnet Location
12.a.d Units 54 Inches Wide (or greater) and/or over 200 Pounds
1. Go to the Bottom Rail. Remove (1) End Cap.
2. Break Open the Slide door. Locate the Nose Caster that was pre-installed within the Strike Stile.
3/8 - 16 Nut
Strike Edge of Rail
DN 0636
Nose Caster
Floor
1/16” (1.59mm)
to 1/8” (3mm)
gap from floor
Figure 12-7 Adjust the Nose Caster
3. Loosen the #8-32 Set Screw. Position the Wheel so it is perpendicular to the Bottom Rail. Retighten the
#8-32 Set Screw.
4. Fully close the Slide door. Ensure the Nose Caster does not hit or scrape the floor. Reinstall the End Cap.
12-37
S1
5
A
M
P
GROUND HARNESS
P/N 14-11872
ON/OFF
POWER
SWITCH
1
NR
T1
AUXILIARY 120 VAC
POWER WIRES
(THESE WIRES NORMALLY
COILED AND TIED UP)
120 VAC
TB2
NABCO
WHITE
BLACK
BROWN
BLUE
POWER SUPPLY HARNESS
P/N 14-11874
MADE IN JAPAN
DS-1500
D24-113270
GYRO TECH
RED
NABCO
OUTPUT TIMER
0 = (DO NOT USE)
1 = (DO NOT USE)
2 = (DO NOT USE)
3 = ELECTRIC STRIKE FUNCTION
OUTPUT: 0 = ELECTRIC STRIKE OUTPUT
OUTPUT TIMER
1.0 SEC
OPENING
3 SEC
ON
FULLY CLOSED
OUTPUT SIGNAL
OFF
ACTIVATION SIGNAL OFF
CLOSING
FULL OPEN
ON
FULLY CLOSED
U30 ELECTRIC STRIKE OUTPUT SIGNAL
HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER = 0, 1 or 2, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE
WIRING FOR ELECTRIC LOCK ONLY SHOWN
P/N 24-11877
SYMBOL No.
9DC12V 1
1
7
2
2
3
61
3
6B
4
4
5
H
5
6
M0
6
7
M1
7
Exterior Activation
8
62
8
SQ
9
9
Breakout Detector
10
BA
10
11
SLS
11
12
N/O
OUT.A
12
GRAY (OUT B)
30V(42.4Vpeak)max.
13
N/C
OUT.B
13
VIOLET
5Amax.(0-20V), 3.2Amax.(20-30V)
14
14
Common OUT.C
15
OUT
15
7
16
16
12VDC-COMMON
LABEL ON U30 CONTROL
TERMINAL ON U30 MAIN HARNESS
12VDC+
12VDC-(COMMON)
INTERIOR ACTIVATION
HOLDING BEAM
REDUCED OPENING SWITCH
GROUND LUG
SCREW TO HEADER
BLACK (HOT)
WHITE (COMMON)
AC115V 10
50/60 H
TB1
NR
2
NOISE
FILTER
POWER SUPPLY P/N 14-11741
TRANSFORMER
RELATED DEVICES - 16P
NA
BC
O
5 6 7
POWER SUPPLY
14-14299
BLACK
E IT MO E
RED
BLACK
IN ICATORS
A
2
!
!
T
!
M
O
O
G
G
SW U
M1
Ad ustments to the door can only e made
A
C
S
2A
O
S
-C
2L
2 -
UNCTION SLI ING OOR
C
24 9 1-
NO
NC
C
M
M1
2
S
A
SLS
OUT A
OUT
OUT C
OU T
1
SYM OL
9 C12
AN Y TERMINAL P
MAGNETIC LOCK
S
P
C
O
42 4
A
-2
A
O
12 C- C
E
R
O
M
12 C
12 C- C
I
N
9
1
11
12
1
14
1
1
4
N .
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
N1
Some magnetic locks (as well other types of locks)
require a voltage suppression device such as a diode
or MOV. Connect here if needed.
Read the instructions provided with the lock for details.
To maintain warranty,repairs must e
made y authori ed NABCO facilities.
Do not disassem le the control ox.
There are no user servicea le parts
inside.
MO E
TWO WAY
ONE WAY
OL OPEN
NIG T
A NIN
M
O
G
G
O
! CAUTION
GYRO TEC
NABCO
!
U30 MICROPROCESSOR CONTROL
P/N 24-8901-30
MOTOR 12P
1
O
ERROR
POWER 2P
2 AC
MOTOR/OPERATOR
P/N 24-11327
2 34
0 7
8 9 10
11 12 1
13-38
POM
U WIT MAGNETIC LOCK
NOTE LOCK WORKS ONLY IN NIG T MO E
Part #15-9244-30
Rev. 10-27-15
Section 13a: U30 with Magnetic Lock
CHAPTER 13: ELECTRIC LOCK WIRING
Electric Lock Wiring
5
A
M
P
GROUND HARNESS
P/N 14-11 72
ON/OFF
POWER
SWITCH
S1
T1
10
11
12
13
14
15
16
1
2
3
4
5
6
7
VIOLET
GRAY (OUT A)
P/N 24-11 77
SYMBOL N .
DC12V 1
7
2
61
3
6B
4
5
H
M0
6
)
7
M1
62
S
10
BA
11
SLS
12
OUT.A
13
OUT.B
14
OUT.C
15
OUT
7
16
AUXILIARY 120 VAC
POWER WIRES
COILED AND TIED UP)
120 VAC
TB2
MOTOR/OPERATOR P/N 24-11327
OUTPUT TIMER
0 = (DO NOT USE)
1 = (DO NOT USE)
2 = (DO NOT USE)
OPENING
3 SEC
ON
FULLY CLOSED
OFF
ON
CLOSING
FULL OPEN
FULLY CLOSED
6
1
INDICATORS
T
D
T
A
.
GYRO TECH
FAIL SECURE LOCK ASSY.
P.N. 22-10522-03
GRY
VIO
BLK
WHT
110V
ERROR
BA
62
H
6B
61
POWER
MOTOR･12P
T
,
z
NABCO H T
.
M
N .
24
01-
.
NABCO
.
S
(
M
SW U
.
FAIL
SECURE
E
A
S
A
B
D
S
P
S
C
O
(C
2L
30V(42.4V
) .
5A
.(0-20V), 3.2A
.(20-30V
)
A
O
(O
) -C
12VDC-(C
)
M
N/O
N/C
C
SYMBOL N .
DC12V 1
2
7
3
61
4
6B
5
H
6)
M0
M1
7
62
S
BA
10
SLS
11
)
OUT.A 12
OUT.B 13
OUT.C 14
OUT
15
7
16
C
HANDY TERMINAL･6P
01-30
SW U
M1
MODE
O
FUNCTION SLIDING DOOR
TWO WAY
O
ONE WAY 12VDC
)
G
HOLD OPEN 12VDC-(C
I
A
G
NIGHT
H
B
R
O
S
,
CAUTION
M0
O
G
G
O
M
NABCO
WARNING
U30 CONTROL P/N 24-
DN 0552
10
11
12
13
14
15
16
1
2
3
4
5
6
7
Rev. 10-27-15
OUTPUT TIMER
1.0 SEC
OUTPUT SIGNAL
ACTIVATION SIGNAL
OFF
BLACK
WHITE
P/N 14-11 74
HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER = 3, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE
E
A
S
A
B
D
S
P
S
C
O
(C
2L
N/O )
30V(42.4V
)
.
N/C
5A
.(0-20V), 3.2A
.(20-30V)
C
A
O
(O
) -C
12VDC-COMMON
FUNCTION SLIDING DOOR
12VDC
12VDC-(COMMON)
INTERIOR ACTIVATION
HOLDING BEAM
M
S
(
M
SW U
GROUND LUG
SCREW TO HEADER
AC115V ± 10%
50 / 60 Hz
BLACK (HOT)
WHITE (COMMON)
TB1
ZN
R1
R2
ZN
NOISE
FILTER
TRANSFORMER
MADE IN JAPAN
DS-150ＮＡ
GYRO TECH
（24-11327）
POWER･2P
20VAC 50/60Hz
U30 WITH FAIL SECURE ELECTRIC LOCK
NOTE: LOCK WORKS ONLY IN NIGHT MODE & EXIT MODE
Part #15-9244-30
Section 13b: U30 with Fail Secure Electric Lock
13-39
GROUND HARNESS
P/N 14-11872
ON/OFF
POWER
SWITCH
S1
5
A
M
P
T1
TB2
AUXILIARY 120 VAC
POWER WIRES
COILED AND TIED UP)
120 VAC
TRANSFORMER
OUTPUT TIMER
0 = (DO NOT USE)
1 = (DO NOT USE)
2 = (DO NOT USE)
GRAY
BLACK
FULLY CLOSED
OFF
OPENING
3 SEC
CLOSING
FULL OPEN
ON
FULLY CLOSED
VIOLET
WHITE
P/N 14-11874
POM
6
1
INDICATORS
WARNING
To maintain warranty,repairs must e
made y authori ed NABCO facilities.
Do not disassem le the control ox.
There are no user servicea le parts
e made
CAUTION
HANDY TERMINAL･6P
248901-
No.
OTHER WIRES NOT SHOWN
FOR SIMPLICITY
FAIL
SAFE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DN 0551
SYMBOL No.
9DC12V 1
7
2
61
3
6B
4
H
5
M0
6
M1
7
Exterior Activation
62
8
SQ
9
Breakout Detector
BA
10
SLS
11
N/O
OUT.A 12
30V(42.4Vpeak)max.
N/C
OUT.B 13
5Amax.(0-20V), 3.2Amax.(20-30V)
Common OUT.C 14
OUT
15
12VDC-(Common)
7
16
Mode SW Usage
M0
M1
MODE
Open Open TWO WAY
Gnd Open ONE WAY 12VDC+
Gnd
Gnd HOLD OPEN 12VDC-(Common)
Open Gnd NIGHT
Interior Activation
Holding Beam
Ad ustments to the door can only
GYRO TECH
FAIL SAFE LOCK ASSY.
P.N. 22-10522-04
GRY
VIO
BLK
WHT
110V
ERROR
BA
62
H
6B
61
POWER
MOTOR･12P
U30 CONTROL P/N 24-8901-30
Part #15-9244-30
OUTPUT TIMER
1.0 SEC
OUTPUT SIGNAL
ACTIVATION SIGNAL OFF
ON
6
MOTOR/OPERATOR P/N 24-11327
HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER = 3, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE
P/N 24-11877
SYMBOL No.
9DC12V 1
1
7
2
2
61
3
3
6B
4
4
5
H
5
6
M0
6
7
M1
7
Exterior Activation
62
8
8
SQ
9
9
Breakout Detector
10
BA
10
11
SLS
11
12
N/O
OUT.A
12
30V(42.4Vpeak)max.
13
FAIL SAFE (OUT B)
N/C
OUT.B
13
5Amax.(0-20V), 3.2Amax.(20-30V)
14
14
Common OUT.C
15
OUT
15
7
16
16
12VDC-COMMON
12VDC+
12VDC-(COMMON)
INTERIOR ACTIVATION
HOLDING BEAM
GROUND LUG
SCREW TO HEADER
BLACK (HOT)
WHITE (COMMON)
A C115V 10
50 / 60 H
TB1
2
NR
NR
1
NOISE
FILTER
MADE IN APAN
DS-150ＮＡ
GYRO TECH
（24-11327）
2 34
0 7
8 9 10
11 12 1
13-40
POWER･2P
20VAC 50/60H
U30 WITH FAIL SAFE ELECTRIC LOCK
NOTE: LOCK WORKS ONLY IN NIGHT MODE & EXIT MODE
Rev. 10-27-15
Section 13c: U30 with Fail Safe Electric Lock
Rev. 10-27-15
Part #15-9244-30
Section 13d: Strike Adjustment
For detailed Electric Lock Wiring information and instructions, please refer to; P/N 15-10596-30, U30
Electric Manual”.
Electric Lock Assembly
LATCHBOLT POSITION:
• BIPART UNITS
• LH SINGLE F.O.
• RH SINGLE F.S.
Dead Bolt Engaged with Electric Strike
Electric Strike
(Door in Full Closed Posion)
Slight Gap
(Between Strike Wall
and Dead Bolt)
Belt Clip
Terminal Strip
(Strike Side of Door)
Dead Bolt Assembly
LATCHBOLT POSITION:
• RH SINGLE F.O.
• LH SINGLE F.S.
DN 1026
Figure 13-1 Adjust the Strike
13-41
S1
PRESS
TO
RESET
Common
N/O
N/C
LOAD
TWO WAY
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
PN 14-11875
KEY SWITCH
FOR U30
PN 14-11876
FULL
OPEN
ORANGE
RED
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
WHITE
WHITE
U30 TERMINAL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WHITE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
BLUE
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
MADE IN JAPAN
DS-1500
D24-113270
GYRO TECH
NABCO
NABCO
NA
BC
O
1211
7 0
1
!
!
! WARNING
M0
Open
Gn d
Gn d
Open
Mode SW Usage
MODE
M1
Open
TWO WAY
Open
ONE WAY
Gn d
HOLD OPEN
Gn d
NIGH T
To protect against risk of Fire or electric shock,use only the
cerfied NABCO power supply.
inside.
! CAUTION
GYRO TECH
!
NABCO
Exterio r Acvaon
Sequenal Acvaon
Breakout Detector
30V(42.4Vpeak)max
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
Mode Switch (see Mode SW Usage shown le)
12VDC +
12VDC-(Common)
Interior Acvao n
Holding Beam
FUNCTION (SLIDING DOOR)
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
U30 TERMINAL
P/N 24-11877
DN 0539
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
BROWN &RED
(CIRCUIT 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Optex OS-12C
Controller
RED
TERM #4
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WHITE
TERM #5
EXTERIOR ACUSENSOR
PT. NO. 14-8902
YELLOW
GRAY
BROWN
BLK/RED
P/N 14-11874
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT. A
OUT. B
OUT. C
OU T
7
HANDY TERMINAL 6P
248901-
No.
Power Harness
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
INTERIOR ACUSENSOR
PT. NO. 14-8902
YELLOW
GRAY
BROWN
BLK
MAIN HARNESS FOR U30
P/N 24-11877
ERROR
BA
62
H
6B
61
POWER
MOTOR 12P
P/N 24-8901-30
Part #15-9244-30
REDUCED OPEN
RED
BLUE
WHITE
WHITE
BLUE
TB2
Auxiliary 120 VAC
Power Wires
(These wires are normally
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
U30 MICROPROCESSOR CONTROL LABEL
Breakout Detector
30V (42.4V peak) max.
5A max, (0-20V), 3.2A max. (20-30V)
Auxiliary Output (Open Collector)
12VDC Common
Mode Switch
Holding Beam
-CIRCUIT-BREAKERRED INDICATES
POWER IS OFF
T1
8
12 VDC+
12VDC- (Common)
P/N 14-11872
TB1
NOISE
FILTER
ON/OFF
Power Switch
PE
Grounding Wire
(Common)
White Wire
AC115V ± 10%
50 / 60 Hz
MOTOR/OPERATOR
P/N 24-11327
3 2
4
INDICATORS
POWER 2P
20VAC 50/60Hz
POWER SUPPLY
P/N 14-11741
14-42
N
7 6 5
L
10 9
Related Devices - 16P
>POM
<
Black Wire (Hot)
Rev. 10-27-15
CHAPTER 14: GENERAL WIRING
14.1 (2) Acusensors and (1) Holding Beam
General Wiring
General Wiring
Common
N/O
N/C
LOAD
TWO WAY
FULL
OPEN
ORANGE
RED
REDUCED OPEN
RED
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
BLUE
WHITE
WHITE
BLUE
WHITE
WHITE
U30 TERMINAL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NABCO
WHITE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
BLUE
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
MADE IN JAPAN
DS-1500
D24-113270
GYRO TECH
NABCO
NA
BC
3 2
1
1211
7 0
!
!
M0
Open
Gn d
Gn d
Open
Mode SW Usage
MODE
M1
Open
TWO WAY
Open
ONE WAY
Gn d
HOLD OPEN
NIGH T
Gn d
! WARNING
To protect against risk of Fire or electric shock,use only the
cerfied NABCO power supply.
inside.
! CAUTION
GYRO TECH
NABCO
GRAY
WHITE
GRAY
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
U30 TERMINAL
P/N 24-11877
DN 0685
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
BROWN &RED
(CIRCUIT 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Optex OS-12C
Controller
RED
TERM #4
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WHITE
TERM #5
N/O
N/C
Common
EXTERIOR OPTEX I-1
PT. NO. 14-13036
YELLOW
GRAY
YELLOW
Mode Switch (see Mode SW Usage shown le)
Exterio r Acvaon
Sequenal Acvaon
Breakout Detector
30V(42.4Vpeak)max
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT. A
OUT. B
OUT. C
OU T
7
HANDY TERMINAL 6P
248901-
No.
FUNCTION (SLIDING DOOR)
12VDC +
12VDC-(Common)
Interior Acvao n
Holding Beam
BLK
BROWN
BLK/RED
OPTEX
HARNESS
P/N 12-13018
WHITE
GRAY
ERROR
BA
62
H
6B
!
MOTOR 12P
61
POWER
Power Harness
P/N 14-11874
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
INTERIOR OPTEX I-1
PT. NO. 14-13036
YELLOW
GRAY
YELLOW
GRAY
BROWN
BLK
P/N 24-11877
O
P/N 24-8901-30
Rev. 10-27-15
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
PN 14-11875
KEY SWITCH
FOR U30
PN 14-11876
TB2
Auxiliary 120 VAC
Power Wires
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
T1
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
Breakout Detector
5A max, (0-20V), 3.2A max. (20-30V)
12VDC Common
Mode Switch
Holding Beam
S1
PRESS
TO
RESET
RED INDICATES
POWER IS OFF
-CIRCUIT-BREAKER-
NOISE
FILTER
ON/OFF
Power Switch
TB1
MOTOR/OPERATOR
P/N 24-11327
POWER SUPPLY
P/N 14-11741
8
12 VDC+
12VDC- (Common)
Grounding Wire
P/N 14-11872
White Wire
(Common)
AC115V ± 10%
50 / 60 Hz
PE
4
INDICATORS
POWER 2P
20VAC 50/60Hz
N
7 6 5
L
10 9
>POM
<
Black Wire (Hot)
Part #15-9244-30
14.2 (2) Optex i-One Sensors, (1) Holding Beam and (1) Breakout Beam
14-43
S1
PRESS
TO
RESET
RED INDICATES
POWER IS OFF
-CIRCUIT-BREAKER-
N/O
N/C
Common
TWO WAY
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
PN 14-11875
KEY SWITCH
FOR U30
PN 14-11876
FULL
OPEN
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
WHITE
WHITE
WHITE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
PN 14-11884
BLUE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
WHITE
U30 TERMINAL
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MADE IN JAPAN
DS-1500
D24-113270
GY RO TECH
NABCO
NA
O
BC
1 12
11
7 0
43 2
MOTOR/OPERATOR
P/N 24-11327
ERROR
BA
62
H
6B
61
! CAUTION
Mode SW Usage
MODE
M0
M1
Open
Open
TWO WAY
Open
Gnd
ONE WAY
GndG
nd HOLD OPEN
Open
Gnd
NIGHT
inside.
Exterior Activation
Breakout Detector
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
Interior Activation
Holding Beam
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
HANDY TERMINAL･6P
248901-
No.
12VDC+
12VDC-(Common)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WHITE
GRAY
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
BLUE
(TERM #4)
BLUE
(TERM #3)
U30 TERMINAL
P/N 14-11873
TERM #1
TERM #1
BROWN &RED
(TERM 1 & 2)
DN 0542
OPTEX
OPTEX
HOLDING BEAM BREAKOUT BEAM
CONTROLLER
CONTROLLER
PT. NO.
PT. NO.
PN 14-9710-03
PN 14-9710-03
Optex OS-12C
Controller
BROWN &RED
(TERM 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Optex OS-12C
Controller
RED
TERM #4
WHITE
TERM #5
EXTERIOR OPTEX I-ONE
PN 14-10364-A
YELLOW
GRAY
YELLOW
GRAY
BROWN
BLK/RED
OPTEX
HARNESS
PN 12-13018
WHITE
GRAY
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
INTERIOR OPTEX I-ONE
PN 14-10364-A
YELLOW
GRAY
YELLOW
GRAY
BROWN
BLK
P/N 24-11877
! WARNING
U30 MICROPROCESSOR CONTROLLER
P/N 24-8901-30
!
!
!
NABCO
GYRO TECH
MOTOR･12P
POWER
Power Harness P/N 14-11874
NABCO
Part #15-9244-30
ORANGE
RED
REDUCED OPEN
RED
BLUE
WHITE
BLUE
TB2
Auxiliary 120 VAC
Power Wires
(These wires are
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
T1
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
U30 MICROPROCESSOR CONTROLLER LABEL
Breakout Detector
5A max, (0-20V), 3.2A max. (20-30V)
12VDC Common
Mode Switch
Holding Beam
12 VDC+
12VDC- (Common)
P/N 14-11872
PE
ON/OFF
Power Switch
TB1
NOISE
FILTER
8
Grounding Wire
(Common)
White Wire
AC115V ± 10%
50 / 60 Hz
LOAD
POWER SUPPLY
P/N 14-11741
INDICATORS
POWER･2P
20VAC 50/60Hz
14-44
N
7 65
L
10 9
>POM
<
Black Wire (Hot)
Rev. 10-27-15
14.3 (2) Optex i-One Sensors, (1) Holding Beam and (1) Breakout Beam
General Wiring
General Wiring
-CIRCUIT-BREAKER-
S1
PRESS
TO
RESET
RED INDICATES
POWER IS OFF
Common
N/O
N/C
LOAD
TWO WAY
FULL
OPEN
ORANGE
RED
REDUCED OPEN
RED
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
BLUE
WHITE
WHITE
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
P/N 14-11884
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
WHITE
U30 TERMINAL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MADE IN JAPAN
DS-1500
D24-113270
GY RO TECH
NABCO
NABCO
O
BC
7 0
11
1 12
INDICATORS
ERROR
BA
62
H
6B
! WARNING
inside.
! CAUTION
Mode SW Usage
M0
M1
MODE
Open
Open
TWO WAY
Open
ONE WAY
Gnd
GndG
nd HOLD OPEN
Open
NIGHT
Gnd
Exterior Activation
Breakout Detector
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
Interior Activation
Holding Beam
12VDC-(Common)
12VDC+
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
HANDY TERMINAL･6P
248901-
No.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BLUE
(TERM #4)
BLUE
(TERM #3)
U30 TERMINAL
P/N 14-11873
OPTEX OS-12C
Controller
TERM #1
TERM #1
BROWN &RED
(TERM 1 & 2)
OPTEX OS-12C
Controller
BROWN &RED
(TERM 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DN 0541
OPTEX
OPTEX
CONTROLLER
CONTROLLER
PT. NO.
PT. NO.
P/N 14-9710-03 P/N 14-9710-03
ACUSENSOR
EXTENSION
HARNESS
P/N 22-9267-00
RED
RED
WHITE
(TERM #5)
RED
(TERM #4)
EXTERIOR ACUSENSOR
P/N
YELLOW
GRAY
BROWN
BLK/RED
WHITE
Power Harness (P/N 14-11874)
!
!
!
NABCO
GYRO TECH
MOTOR･12P
61
POWER
ACUSENSOR
EXTENSION
HARNESS
P/N 22-9267-00
RED
RED
INTERIOR ACUSENSOR
P/N
YELLOW
GRAY
BROWN
BLK
Main Harness For U30
P/N 24-11877
NA
P/N 24-8901-30
Rev. 10-27-15
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
P/N 14-11875
KEY SWITCH
FOR U30
P/N 14-11876
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BLUE
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
Mode Switch (See Mode SW Usage Shown Le )
Exterior Ac va on
al Ac va on
Breakout Detector
5A max, (0-20V), 3.2A max. (20-30V)
12VDC Common
TB2
Auxiliary 120 VAC
Power Wires
coiled and ed up)
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
T1
8
12 VDC+
12VDC- (Common)
Interior Ac va on
Holding Beam
P/N 14-11872
TB1
NOISE
FILTER
ON/OFF
Power Switch
PE
Grounding Wire
(Common)
White Wire
AC115V ± 10%
50 / 60 Hz
MOTOR/OPERATOR
P/N 24-11327
32
4
N
POWER･2P
20VAC 50/60Hz
L
7 65
POWER SUPPLY
P/N 14-11741
<
10 9
>POM
Black Wire (Hot)
Part #15-9244-30
14.4 (2) Acusensors, (1) Holding Beam and (1) Breakout Beam
14-45
S1
PRESS
TO
RESET
RED INDICATES
POWER IS OFF
-CIRCUIT-BREAKER-
N/O
N/C
Common
TWO WAY
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
PN 14-11875
KEY SWITCH
FOR U30
PN 14-11876
FULL
OPEN
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
WHITE
WHITE
WHITE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BLUE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
O
BC
1 12
11
7 0
MOTOR/OPERATOR
P/N 24-11327
ERROR
BA
62
H
YELLOW
BLACK
BLUE
GREEN
On Remote Control Set: “F1” to “1”
If programming without the Remote: Parameter “13” to “1”
RED
BROWN
WHITE
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
INTERIOR IXIO
PN 14-14264
GRAY
BROWN
BLK
P/N 24-11877
! WARNING
inside.
! CAUTION
Mode SW Usage
MODE
M0
M1
Open
Open
TWO WAY
Open
Gnd
ONE WAY
GndG
nd HOLD OPEN
Open
Gnd
NIGHT
Exterior Activation
Breakout Detector
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
Interior Activation
Holding Beam
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
HANDY TERMINAL･6P
248901-
No.
12VDC+
12VDC-(Common)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BLACK
BLUE
GREEN
YELLOW
RED
BROWN
WHITE
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
BLUE
(TERM #4)
BLUE
(TERM #3)
U30 TERMINAL
P/N 14-11873
Optex OS-12C
Controller
TERM #1
TERM #1
BROWN &RED
(TERM 1 & 2)
Optex OS-12C
Controller
BROWN &RED
(TERM 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DN 0555
OPTEX
OPTEX
CONTROLLER
CONTROLLER
PT. NO.
PT. NO.
PN 14-9710-03
PN 14-9710-03
WHITE
TERM #5
EXTERIOR IXIO
PN 14-14264
GRAY
BROWN
BLK/RED
RED
TERM #4
P/N 24-8901-30
!
!
!
NABCO
GYRO TECH
MOTOR･12P
6B
61
POWER
NA
43 2
White and Green wires from Sensor provide output for
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
PN 14-11884
MADE IN JAPAN
DS-1500
D24-113270
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
WHITE
U30 TERMINAL
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NABCO
GY RO TECH
NABCO
Part #15-9244-30
ORANGE
RED
REDUCED OPEN
RED
BLUE
WHITE
BLUE
TB2
Auxiliary 120 VAC
Power Wires
(These wires are
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
T1
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
Breakout Detector
5A max, (0-20V), 3.2A max. (20-30V)
12VDC Common
Mode Switch
Holding Beam
12 VDC+
12VDC- (Common)
P/N 14-11872
PE
ON/OFF
Power Switch
TB1
NOISE
FILTER
8
Grounding Wire
(Common)
White Wire
AC115V ± 10%
50 / 60 Hz
LOAD
POWER SUPPLY
P/N 14-11741
INDICATORS
POWER･2P
20VAC 50/60Hz
14-46
N
7 65
L
10 9
>POM
<
Black Wire (Hot)
Rev. 10-27-15
14.5 (2) IXIO, (1) Holding Beam and (1) Breakout Beam
General Wiring
General Wiring
S1
PRESS
TO
RESET
RED INDICATES
POWER IS OFF
-CIRCUIT-BREAKER-
N/O
N/C
Common
TWO WAY
HOLD OPEN
ONE WAY
NIGHT
OFF
ON
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
FOR U30
PN 14-11875
KEY SWITCH
FOR U30
PN 14-11876
FULL
OPEN
ORANGE
RED
ORG/WHT
RED
GREEN
ORG/WHT
RED
ORANGE
WHITE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WHITE
BLUE
RED
RED
ORG/WHT
BLUE
GREEN
ORANGE
O
BC
11
7 0
1 12
MOTOR/OPERATOR
P/N 24-11327
H
ERROR
BA
62
YELLOW
BLACK
BLUE
GREEN
On Remote Control Set: “F1” to “1”
If programming without the Remote: Parameter “13” to “1”
RED
BROWN
WHITE
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
INTERIOR IXIO
PN 14-14264
GRAY
BROWN
BLK
P/N 24-11877
! WARNING
inside.
! CAUTION
Mode SW Usage
MODE
M0
M1
Open
Open
TWO WAY
Open
Gnd
ONE WAY
GndG
nd HOLD OPEN
Open
Gnd
NIGHT
Exterior Activation
Breakout Detector
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
Interior Activation
Holding Beam
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
HANDY TERMINAL･6P
248901-
No.
12VDC+
12VDC-(Common)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BLACK
BLUE
GREEN
YELLOW
GRAY
BROWN
BLK/RED
EXTERIOR IXIO
PN 14-14264
RED
BROWN
WHITE
ACUSENSOR
EXTENSION
HARNESS
PN 22-9267-00
RED
RED
U30 TERMINAL
P/N 14-11873
Optex OS-12C
Controller
TERM #1
BROWN &RED
(c IRc UIt 1 & 2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DN 0554
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
WHITE
TERM #5
RED
TERM #4
P/N 24-8901-30
!
!
!
NABCO
GYRO TECH
MOTOR･12P
6B
61
POWER
NA
43 2
White and Green wires from Sensor provide output for
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
PN 14-11884
MADE IN JAPAN
DS-1500
D24-113270
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
YELLOW
BLUE
GRN/WHT
WHITE
U30 TERMINAL
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
BLUE
BLUE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NABCO
GY RO TECH
NABCO
Rev. 10-27-15
REDUCED OPEN
RED
BLUE
WHITE
WHITE
TB2
Auxiliary 120 VAC
Power Wires
(These wires are
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
T1
9DC 12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
Out.A
Out.B
Out.C
Out
7
Breakout Detector
5A max, (0-20V), 3.2A max. (20-30V)
12VDC Common
Mode Switch
Holding Beam
12 VDC+
12VDC- (Common)
P/N 14-11872
PE
ON/OFF
Power Switch
TB1
NOISE
FILTER
8
Grounding Wire
(Common)
White Wire
AC115V ± 10%
50 / 60 Hz
LOAD
POWER SUPPLY
P/N 14-11741
INDICATORS
POWER･2P
20VAC 50/60Hz
N
7 65
L
10 9
>POM
<
Black Wire (Hot)
Part #15-9244-30
14.6 (2) IXIO, and (1) Holding Beam
14-47
Part #15-9244-30
Rev. 10-27-15
CHAPTER 15: HANDING
WHEN VIEWED FROM BREAKOUT SIDE
TYPICALLY EXTERIOR
Full Open Units: Doors slide behind Sidelite
Fixed Sidelite Units: Doors slide in front of Sidelite
Le Hand:
Door slides to the Le
Right Hand:
Door slides to the Right
Le Hand
Right Hand
DN 1381
15.a Test the Handing
1. Turn Power OFF.
2. Manually slide the Slide door half way open.
3. Turn Power ON. The Slide door should slowly close (per Power On factory settings).
15.b Install the Handing Harness
1. Turn Power OFF.
2. Obtain the Handy Terminal Harness. Plug the Telephone Jack end into the U30 Microprocessor
Control. Remove the Protective Cap from the female end.
3. Obtain the Cable. Slide back the metal sleeve on the male end of the Cable. Connect the Cable to the
female end of the Handy Terminal Harness.
a. The male end of the Cable has multiple prongs that must line up with the socket. Gently turn
the plug end clockwise while trying to insert the male end until a connection can be made.
4. Connect the other end of the Cable to the Handy Terminal. Turn Power ON.
5. Press: ENTRY until the screen displays: SPECIAL FUNCTION ADJUSTMENTS Then select: Y
6. Continue pressing: ENTRY until the Screen displays: RECYCLE Change the setting Y/N.
7. Disconnect the Handy Terminal.
a. Wait at least (10) seconds before disconnecting Handy Terminal to allow last test to
complete and message display
to stabilize.
15-48
8. Turn Power OFF.
Handing
Rev. 10-27-15
Part #15-9244-30
9. Manually slide the Slide door half way open.
1. Turn Power ON.
2. The Slide door should slowly close (per Power ON factory settings).
3. Plug the Handy Terminal back into the Terminal Connector.
Handy Terminal Harness
P/N M-01517
INDICATORS
GYRO TECH
6B
H
POWER･2P
20VAC 50/60Hz
M0
Open
Gnd
Gnd
Open
Mode SW Usage
MODE
M1
Open
TWO WAY
Open
ONE WAY
Gnd HOLD OPEN
NIGHT
Gnd
! CAUTION
62
BA
ERROR
!
NABC O
61
!
inside.
!
HANDY TERMINAL･6P
No.
248901FUNCTION [SLIDING DOOR]
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
Exterior Activation
Breakout Detector
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
12VDC-(Common)
N/O
N/C
Common
SYMBOL
9DC12V
7
61
6B
H
M0
M1
62
SQ
BA
SLS
OUT.A
OUT.B
OUT.C
OUT
7
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
! WARNING
MOTOR･12P
POWER
Handy Terminal
P/N V-00356
P/N V-00020
DN 1367
Handing
Remove Protecve Cap from
the Handy Terminal Harness
Cable
P/N M-01410
Figure 10-1 Connect the Handy Terminal to the U30 Microprocessor Control
15-49

Model GT 1175 Standard Slide Doors **with U30 Control

Transcription

Similar documents

Zak McKracken – Mayan Maze Map

Rilo Kiley After Hours

“Over 125 Years of Quality” Double Acting Spring Hinges

SILENTIUM PM 42S

Adult NL Spring 14.pages

Heavy Duty Concealed Magnetic Catch suitable for full size doors

hawa-junior 80 and 80/b sliding door system

The Blanc - Westeck Windows and Doors

Bobs Stores

DOMETIC® AMERICANA REFRIGERATORS