Holiday Ornaments YOU WILL NEED: Pegboards: Bead Colors:

Transcription

Holiday Ornaments YOU WILL NEED: Pegboards: Bead Colors:
Holiday Ornaments
YOU WILL NEED:
Pegboards:
Bead Colors:
Tree
Small Circle
Large Circle
Red 15005
Yellow 15003
Prickly Pear 15097
Green 15080
Dark Green 15010
Neon Blue 15089
Blueberry Cream 15093
Light Brown 15021
Grey 15017
White 15001
You will also need assorted adhesive gems, 1/8" silver ribbon, silver
metallic thread, needle, a lollipop stick, cellophane candy bag, and
quick-drying adhesive to complete your project.
Instructions
1. Place your beads on the pegboards as shown. If you are using
a clear pegboard, slide the actual-size pattern underneath it.
2. Ask an adult to fuse your designs—see Fusing Instructions on
page 4.
3. Assembly: See each project for assembly notes. All ornament
hangers are made with the silver metallic thread.
Christmas
Tree
Bead Color/# Needed:
Yellow - 6
Dark Green - 226
Light Brown - 9
Assembly
T urn the pieces at right angles to each
other and connect slot to slot. Glue if
needed. Add adhesive gems to decorate
the tree, then add a hanger through the
top bead.
1
Holiday Ornaments
Light Bulb
Garland
Make 1 light bulb in red, 1 in
green, and 1 in neon blue
Bead Color/# Needed:
Red - 52
Green - 52
Neon Blue - 52
Grey - 21
White - 12
Assembly
Cut a long length of silver ribbon. Create the garland
by wrapping the ribbon around the grey beads
section of each light bulb and gluing in place. Tie a
bow at each end.
Long
Ornament A
Bead Color/# Needed:
Blueberry Cream - 54
Neon Blue - 86
Grey - 6
2
Holiday Ornaments
Long
Ornament B
Bead Color/# Needed:
Blueberry Cream - 56
Neon Blue - 85
Grey - 4
Assembly
T urn pieces A and B at right
angles to each other and
connect slot to slot. Glue if
needed. Wrap silver ribbon
around the upper and lower
portions of the ornament and
tie bows. Add a hanger
through the top bead.
Lollipop
Bead Color/# Needed:
Prickly Pear - 40
Green - 122
Assembly
lue a lollipop stick in the
G
opening. Insert lollipop into a
candy bag and tie closed
with ribbon. Add a hanger
through the top bead (use a
needle to go through the bag
as well).
3
Holiday Ornaments
Peppermint
Ornament
Bead Color/# Needed:
Red - 80
Grey - 5
White - 160
Assembly
Turn the pieces at right angles to each other and connect slot
to slot. Glue as needed. Add a hanger through the top bead.
Fusing Instructions—Only Adults Iron
1. Place your pegboard on a flat, heat-safe surface.
2. Set a household iron to the medium setting. Place ironing paper over the
pegboard. In a circular motion, begin to iron the project. When ironed
properly, the beads will still have an open center. Let the design cool.
3. Remove the paper and bead design from the peg board. Flip the design
over to expose the non-fused side. Repeat step two. Let cool completely.
Note: Beads need heat for about 10-20 seconds per side to fuse evenly. Depending on the size of the project, additional heating time
may be required. If you are working on a 3-D project, DO NOT OVER-IRON the beads as it will make the centers of the beads close
and can make assembly more challenging.
www.eksuccessbrands.com
Perler Beads and EKSuccess Brands are either registered trademarks or trademarks of Dimensions Crafts LLC and
EK Success Ltd. respectively in the United States and/or other countries. © 2011 Dimensions Crafts LLC. All rights reserved.
4