Steps In Time Bracelet Tutorial

In
Conjunction
With
SUPPLIES
23 Pcs-2-hole Tile Beads
54 Pcs-2-hole Brick Beads
5 g-#11 Seed Beads
1 g-#15 Seed Beads
3 g-Magatamas
42-4mm Fire Polish Crystals
1 Button 5/8”
Wildfire or Fireline 6lb or 8lb
Tulip Needle #10 or #11
Makes a 7 1/2” X 1” Bracelet
Add/subtract 2 Tile Beads & 2 Brick Beads to add/subtract 1/4" to the piece.
Designed Exclusively by Good Quill Hunting for Whimbeads.com
© 2013 Good Quill Hunting – All Rights Reserved.
This may NOT be taught or reprinted in any manner .
You may sell your finished work, please give credit to the Designer.
Stop Bead
STEP 1 Leaving about 8-9 inches of
Fireline, tie on a stop bead.
The beginning thread will be used to
make a loop at the end.
String a Tile Bead (TB), a Brick Bead
(BB), #11, Magatama Bead (MB), #11.
Go back down through the BB. String a
TB, BB, #11, MB, #11.. Go through the
opposite side of the BB and up through
the TB, BB, #11, MB, #11, BB and TB.
Come out between the TB and the BB.
STEP 2 Coming up underneath the
TB, repeat this process to the end.
You will have 23 TB for the length
specified on the front page. Make
adjustments now. The closure
section is ½” in the length.
Stop Bead
STEP 3 When you have reached the end, you will have a TB sticking out, just like the beginning
of your bracelet. String 6 #11 and the button and make a circle around the end of the TB
several times to reinforce.
Stop Bead
Designed Exclusively by Good Quill Hunting for Whimbeads.com
© 2013 Good Quill Hunting – All Rights Reserved.
This may NOT be taught or reprinted in any manner .
You may sell your finished work, please give credit to the Designer.
STEP 4 When you have finished with the button, weave around to come out of a MB on top on
one side. Weave a #15, 4mm Fire Polish crystal (FP), and a #15 and go through the next MB.
Do this on both sides. Cut over through the BB and TB’s on the end.
Stop Bead
STEP 5 Weave your way to the other side when you get to the end. Coming out of the 1st #11 on
the BB, string 3 #11 and go through the #15 and FP. String 2 #11, MB, 2 #11 and going over
the top of the FP, go back through to encircle the crystal. Go through the next #15. String 3 #11
and go through the next #15 and FP. Encircle the FP again with 2 #11, MB, 2 #11. Repeat all
the way down and on the other side. Tie off. **The 3 #11’s over the MB will probably pop up a
bit, this is supposed to happen. When you are done the bracelet, you can go down each side and
make sure each 3 #11 section over the MG is popping up.
Stop Bead
Designed Exclusively by Good Quill Hunting for Whimbeads.com
© 2013 Good Quill Hunting – All Rights Reserved.
This may NOT be taught or reprinted in any manner .
You may sell your finished work, please give credit to the Designer.
STEP 6 Take your stop bead off and thread
your needle with the beginning thread. String
25 #11 beads. If you use a different size button,
make sure to compensate for it one way or the
other, Make sure you end up with an odd
count. You will want a bit of looseness
because you will be doing peyote and that will
snug it up a bit tighter around the button. Then
do peyote stitch around the loop, then peyote
stitch one more time using the MB. Tie off.
You are done…enjoy!
**Diagram  is not show full size on the loop.
SUPPLIES
23 Pcs-2-hole Tile Beads
54 Pcs-2-hole Brick Beads
5 g-#11 Seed Beads
1 g-#15 Seed Beads
3 g-Magatamas
42-4mm Fire Polish Crystals
1 Button 5/8”
Wildfire or Fireline 6lb or 8lb
Tulip Needle #10 or #11
To purchase supplies, kits or find other free patterns: http://whimbeads.com
To see more patterns from Good Quill Hunting: http://goodquillhunting.com
Designed Exclusively by Good Quill Hunting for Whimbeads.com
© 2013 Good Quill Hunting – All Rights Reserved.
This may NOT be taught or reprinted in any manner .
You may sell your finished work, please give credit to the Designer.