p.m. 2014 Sacramento County Fair Metal Mania

2014
Sacramento County Fair
Metal Mania
Friday, May 23rd, 2014
Cal Expo Grandstand
Event Starts at 7:30 p.m.
1st $800
2nd $400
3rd $200
Truck Class Rules
All rules are not subject to the interpretation of the officials, how they are type is
how they are, any equipment that the officials consider not in the intent of the
rules will be considered illegal for competition. These are not suggestions, nor is
this a menu. This is what is allowed as far as preparation of the car. Please do
not try to read anything more into these rules.
Safety:
1. Anyone entering the pit area must display a pit pass on their arm.
2. No animals in the pit area.
3. Please keep your pit area clean.
4. Verbal or Physical abuse will not be tolerated.
5. No hot rodding in the pits.
6. A fire extinguisher in your pit area is recommended.
7. No person under the age of 16 allowed in the pit.
8. No one under the age of 18 without a sign waver.
9. No open toe shoes allowed in the pits at any time.
10. No Alcohol, Drugs, Firearms allowed in the pits at any time.
Event:
1.
2.
3.
4.
5.
All injuries must be reported to track officials no matter how minor.
Regulation racing crash helmets must be worn during the entire event.
Long sleeve shirts mandatory, no shorts.
Seat belts must remain buckled during the event.
Drivers must remain in the vehicle with helmet, seatbelt and eye
protection on until notified by an official that it is safe to exit the vehicle.
6. Driver’s Meeting will be attended by drivers you well draw for your heats
at this time.
7. Drivers door hits are illegal. If the hit is deemed by the official to be
careless or intentional, you will be disqualified. If you use your driver’s
door as a defense, we will not enforce the rules. If you use the door
defense repeatedly you will be disqualified.
Questions Contact Bruce Jr.
Cell:530-723-3807
2014 Sacramento County Fair Destruction Derby
[email protected]
8. Sandbagging is not tolerated and will be strictly enforced. Locking up
the brakes prior to a hit for anything other than a driver’s door will be a
cause for disqualification. The fans pay to see a show, put one on for
them.
9. You will be given two minutes for restarts. We try to work with you if
you are hung up. Hitters get more time than sandbaggers.
10. If your car is rolled over during the event after being pushed back over
if the official deems the car and driver to be ok you may continue.
11. Drivers may be disqualified for:
a. Hitting a car when that driver has waved off.
b. Team driving well not be tolerated.
c. Car condition (Anything that endangers participants.)
d. Driver or Pit Crew Behavior.
e. Not stopping when the red flag is out. (If you reposition your car during this
time we will reposition you to the middle of the track.)
12. Every car will be given a flag. If you break off your flag you are done for
that event.
13. Protest must be in writing and must be submitted by a driver only and
must include a protest fee of $250.00 cash. Sorry no checks
Vehicle Rules
TRACK OFFICIALS WILL INSPECT ALL CARS BEFORE THE DERBY. THE TRUNK AND
HOOD AREA OF ALL CARS WILL BE OPENED FOR INSPECTION. ALL CARS MUST PASS A
TECHNICAL INSPECTION TO QUALIFY FOR DERBY. ALL WINNING CARS WILL BE
REINSPECTED AT END OF EACH HEAT AND PRIOR TO LEAVING THE ARENA, AND BEFORE
AWARDS. NO PIT CREW IS ALLOWED IN THE ARENA AREA DURING REINSPECTION OF
WINNING CARS. DRIVERS CAN BE DISQUALIFIED IF THEY DO NOT COMPLY WITH DERBY
RULES AND/OR THE OFFICIALS DECISION DURING THE TECH INSPECTION. ANY CAR
FOUND TO BE ILLEGAL, WILL FORFEIT ALL WINNINGS FOR THAT NIGHT. ALL DECISIONS
MADE BY OFFICIALS ARE FINAL!!!
RULES FOR TECHNICAN INSPECTION
“THIS IS WHAT YOU ARE ALLOWED TO DO TO PREPARE YOUR TRUCK.”
Any added metal, welds, or rods/plates not specifically covered in the rules will have to be completely
removed along with the surrounding metal. CUTTING YOUR TRUCK WILL WEAKEN YOUR TRUCK
SO DON’T ADD ANYTHING THAT YOU ARE NOT SUPPOSED TO ADD.
1. All trucks must be full size American made ½ ton or ¾ ton pickup. No Crew Cabs, Dually’s,
4X4’s, Military. Stock truck beds only, no utility boxes.
2. All glass, side chrome, door handles, flammable material must be removed. Glass cannot be
rolled down, it must be removed. Rear seat must be removed. This must be done before
bringing the vehicle to the event. There will be no building of vehicles in pit. (Please do them at
home.) AFTER YOU HAVE PASSED INSPECTION YOU CANNOT WORK ON YOUR
TRUCK. Please bring it ready to run. This includes changing tires once you have passed
tech.
Questions Contact Bruce Jr.
Cell:530-723-3807
2014 Sacramento County Fair Destruction Derby
[email protected]
3. Material sizes, unless specified in rule are as follows: Chains ½”, Welding filler 3/8” rebar or
¼”x 2” flat stock or ¼”x 2” x 2” angle. All are maximum sizes.
4. Truck # must be installed on both sides, and on roof. Min 18” lettering. Numbers Only!!
5. Gas tanks must be removed from stock location. New tank installed rear of cab passenger
side. Chains, cable, or steel brackets must secure gas tanks. Tanks must be made of steel or
similar quality. 5 gallons max tank. No plastic tank or plastic connectors. Tank must be
installed within safety bars and covered. Holes must be made in the floorboard around the gas
tank for possible spillage.
6. EXCEPTION: Because of newer model cars equipped with fuel injection systems that have to
run with electrical fuel pumps, an electrical kill switch MUST be added and placed where an
official can turn it off as a safety precaution. Drain holes must be in the floorboard for possible
fuel spills, near the gas tank.
7. Batteries must be relocated to front passenger floorboard. Batteries must be covered and
securely attached with bolts, chains or welded. No Plumbers tape. Batteries or battery boxes in
no way may be attached to frame or body bolts.
8. Mandatory Safety Bars: Side bars from dash to back of cab. Cross bars, at dash, behind
driver. Side bars and cross bars must be connected by welding or bolting. Side bars 6”x 3/8”
material min. and cross bars minimum 3” pipe, or square tubing. Schedule #40 min. All 4
corners of safety cage must be welded to frame, 4” max attachment to frame. Front cage
attachment not to exceed center of front axle. Mandatory 2” vertical bars from rear cross bar to
roof with 6” plate connection on roof. Mandatory 2” min. bars (2) from top of cab angled down
to front bed mount (2nd set of bolts back from cab) Rear cross bar may be mounted inside of
bed no more than 3 inches from front of bed panel.
9. Mandatory: Weld or bolt windshield braces (2) from top of opening to bottom of opening to
prevent hood from entering cab.
10. Bumper heights, front and rear, must be a maximum of 20” measured from the ground to
bottom of bumper. Trucks must be raised or lowered to range this height. Spring spacers or
bump stops welded to axel are accepted methods for lifting. Used trucks heights will be
determined by officials.
11. Bumper may be welded to bumper brackets. Bumper brackets may be welded to frames.
Bumper seams may be welded, no fillers or added material. 5mph bumper may be installed
using 6”x ½” flat mounting plates on bumper max. 4”x 14”x ½” flat material with 2” gussets
tying it to bumper or 2”x 4”x ¼” square tubing, channel. Brackets may be installed on the inside
or outside of frame rail, not on top, bottom or stuffed in frame! Bumper brackets will be
measured from bumper, anything over 14” needs to be removed, including stock brackets,
front and rear bumpers. Barden type bumpers may need to be adjusted per official’s
inspections. Trailer hitches and associated connections must be completely removed.
Questions Contact Bruce Jr.
Cell:530-723-3807
2014 Sacramento County Fair Destruction Derby
[email protected]
12. Engines may be chained, bolted or welded to frame. No engine mounts forward of engine
block. 4” max welding of mounts to frame horizontal and 4” max welding of mounts to frame
vertical. Engine Cradles and distributor protectors are allowed as long as they do not add
reinforcement. NEW – distributor protectors are allowed in Pickups.
13. Engine swaps OK and engine setback OK. If engine is moved back the maximum setback
must not exceed beyond the factory firewall. (Example: valve covers must not be past
factory firewall) NOTE: 12” X 12” hole may be cut in firewall for distributor clearance ONLY!
Maximum of 4 motor mounts may be used, no mounts to rear of heads. Engine cradles
allowed but must be welded or bolted to center cross member only, NOT to frame rail. No
pulley protectors will be allowed.
14. Radiators, if used, must be in stock location, may be strapped or wired in, no welding.
15. All trucks must have an engine air cleaner or similar carburetor cover for fire safety.
16. Doors must be chained or welded, filler not to exceed 2” inch stock. Truck bed may be welded
to cab along outside and top 12” max each side.
17. Tailgate must be welded or chained, 2 chains on bottom 2 on top, do not wrap around
bumper, around rear frame ok, chain ¼” to ½” max. Tailgate must not be folded over. Bed
Rails are to remain stock and not be folded over. Tailgate may be welded with 2” angle on the
inside all the way around.
18. Steering, break away joint may be solid; all other steering from steering box to tie rods
must be stock.
19. Hood must be chained or bolted, no welding. Mandatory four bolts or chains, no more no less,
¾” bolts max, chains ½” max. No frame contact. Max 6” gussets welded to body if bolted. Hole
(12”) must be cut out of hood over carburetor for fire suppression
20. Seat belts are Mandatory. Front seat may be bolted or welded down. Bucket seat allowed. In
no way may seat or seat belt be attached to truck frame.
21. CAB and BED body bolts may be up-graded to ½” bolts with 6” washers.
22. Spring clamps, Rear only, 4 per spring, 2” wide x ¼ “ thick max. See officials for any spring
repairs. NO shortening of springs!
23. 16.5” maximum rim size. Any ply tire rating allowed. Valve stem protectors are ok. No
aggressive style tread allowed on drive tires. NO screwing rim to tires.
24. Frame repairs allowed up to 12” total per frame rail. Frame repair must be more than 2”
separated from Bumper mounts. Minimum repair 6”x ½” thick x 4” wide max size. Call for
information.
Questions Contact Bruce Jr.
Cell:530-723-3807
2014 Sacramento County Fair Destruction Derby
[email protected]
25. Chain may be wrapped from rear axle housing and around frame. One each side. No cutting
away body, No welding, No bolting to frame. Two bolts max may be used per chain.
26. It is illegal to weld body seams unless specified in rules
27. It is illegal to weld, paint, undercoat, mud, sand, grind, etc. any portion of car’s frame unless
specified in rules. Used cars must have frame washed of debris (dirt) from prior derbies.
DRIVER AND VEHICLE OPTIONS
(NOT REQUIRED BUT RECOMMENDED)
1. Goggles and Gloves are highly recommended for driver.
2.
PADDED DRIVER’S COMPARTMENT AND DOOR IS HIGHLY RECOMMENDED.
3.
Floor shifter O.K. Mounted to floor OR transmission ONLY not both.
4.
Locked rear end
5. Radiator Fan (electric fan O.K.)
6. Hand throttle
7. Tranny ultra bell housing O.K. in no way can housing be attached to frame, body, or cage.
8. Transmission coolers may be placed inside vehicle, but MUST be covered or in a ice chest.
Transmission cooler box cannot be attached to frame or covering body bolts.
9. Only (1) AUTOMOTIVE A/C condenser allowed in front of radiator bolted to radiator support only. No
A/C condensers out of tractors.
10. Mud screen allowed in front of driver only.
11. Exhaust may be diverted through the hood AKA "ZOOMIES".
12. SAFETY: Drivers door may have iron on outside with no width limit but must not be more than 3
inches past edge of adjacent panel and must be tapered at both ends.
13. ¼” Thick plate under drivers compartment floor OK but MUST NOT be welded or bolted to frame.
Plate cannot be covering or attached to body mounts.
14. Pinion Brakes ok.
Questions Contact Bruce Jr.
Cell:530-723-3807
2014 Sacramento County Fair Destruction Derby
[email protected]