Leupold® DeltaPoint™ Reflex Sight

LED
Aspheric Lens
Intelligent Brightness Control™
Check to ensure that the magazine of the firearm has been
removed or emptied, that the action is open, and that there is
not a round in the chamber. Only after double checking the firearm, verifying
it is empty and safe, should you proceed with the installation of the Delta
Point. Do not look directly into the sun, light arcs or other high-intensity light
sources. Keep away from children. Adjustment lock screws are loosened at
the factory and your firearm should not be fired with the DeltaPoint attached
until these screws are tighened to 4 inch pounds.
Mounting & Operation Instructions
Elevation
Adjustment
For optimum performance and to prevent damage to this precision
instrument, carefully follow all instructions.
The unit operates with one commercially available 3V Lithium battery
(CR 2032) only. Insert the battery into the receptacle located on the
underside of the housing oriented so that the positive pole on the battery
label is visible. Keep the contact surface clean of dirt and corrosion,
cleaning with alcohol if necessary. If you intend to use the DeltaPoint in
a wet environment, we recommend coating the battery on all sides with
petroleum jelly or other electronics grade lubricant/ protectant to prevent
battery corrosion.
Features
Battery Installation
•
Remove the two screws holding
the DeltaPoint to the base and
turn the sight upside down. Place
the Torx wrench or a screwdriver
in the notch and gently pry the
battery loose. Insert a new battery
as described earlier. The precision
pins eliminate the need for any re-adjustment.
•
•
•
•
•
•
•
•
DiamondCoat™, scratch resistant aspheric lens for maximum field of
view, brightness, and resolution.
Proprietary Intelligent Brightness Control™ (IBC™)
Adjustment
Lock Screws
Motion activated on/off illumination feature (Patent Pending)
Extremely durable, ultra light magnesium housing
Small size and weight
Unlimited eye relief
For handguns, rifles and shotguns
Wide field-of-view
Blackened lens edges
Specifications
•
•
•
•
•
•
•
•
•
•
•
Windage
Adjustment
Magnification: 1.0x
Sight window: 26mm x 19mm; 1.02” x 0.75”
Elevation adjustment range: 60 MOA
Windage adjustment range: 60 MOA
60 MOA per revolution of adjustment
Subtension of the aiming point : 3.5 MOA Dot, 7.5 MOA inscribed Delta
Operating Temperature Range: -20°F to +120°F (-29°C to +49°C)
Storage Temperature Range: -40˚F to +160˚F (-40˚C to +71˚C)
Power Supply: 3V with one CR 2032 Lithium battery
Dimensions: (LxWxH) 1.61” x 1.18” x 1.06” (41mm x 30mm x 27mm)
Weight (with battery installed): 0.6oz. (17g)
Package Contents
•
•
•
•
•
•
•
•
•
•
•
DeltaPoint Reflex sight
(1) 3V Lithium battery (CR 2032)
(1) Protective cover
(2) M4 x 0.7mm Torx® head screws for installing the sight on the
mounting plate
(2) 6-48x .210 Torx® screws for installing the S&W® Classic base
(3) Torx® Set Screws
(1) Torx® T-5 wrench
(1) Torx® T-15 wrench
Cross-Slot Mount
(10) Mount Bases with dovetails
Mount Base 1B / Dovetail 1A - Beretta® 92/96 /90-TWO/Taurus PT99
Mount Base 2B / Dovetail 2A - 1911 Standard
Mount Base 3B / Dovetail 3A - Glock® Standard Frame
(will not fit Large Frame .45acp, .45 GAP, 10mm models)
Mount Base 4B / Dovetail 4A - Sig Sauer® P226
Mount Base 5B / Dovetail 5A -Springfield® XD
Mount Base 6B / Dovetail 6A - CZ® 75
Mount Base 7B / Dovetail 7A - HK® HK P2000
Mount Base 8B / Dovetail 8A - Kimber® Fixed/Adjustable
Mount Base 9B / Dovetail 9A - Smith & Wesson® M&P
Mount Base 10B / Insert 10A - Smith & Wesson® Classic
Operating Instructions
(Figure 1)
M4 x 0.7mm Torx Screws
Mount Base
Dovetail
Pistol Frame
Start-Up
Leupold® DeltaPoint™ Reflex Sight
Operating Instructions
Cautions & Warnings:
Installation
Installation on most handguns requires the use of one of the included
mount bases. Leupold recommends utilizing a qualified gunsmith to press/
remove the rear sight from your handgun. Once the rear sight has been
removed, the appropriate dovetail replaces the rear sight, with the part
number facing up. Some installations (Kimber / Smith & Wesson M&P)
require the use of the included set screws to be placed in the dovetail
to hold it in place and the M4 x 0.7mm Torx® screws will fasten into the
dovetail plate extension.
The corresponding mount base for your pistol is placed on top of the slide
and over the dovetail with the flat part number side facing up through the
slot in the base. Once the dovetail and mount base have been placed on
the slide, the DeltaPoint is placed on top of the base. The four holes in the
bottom of the DeltaPoint will align with the four short posts on the mount
base and secure into the dovetail using the two included M4 x 0.7mm
Torx® screws ( Figure 1). Secure the screws by applying 20 inch pounds
of torque. Securing these screws creates a press-fit and will hold the
DeltaPoint firmly in place. Call Leupold customer service for details specific
to your handgun. For rifle / shotgun applications, the Cross-Slot Mount
allows fast and easy mounting on Weaver-style or Picatinny bases / rails.
Smith & Wesson® Revolver Mount
(For use with Smith & Wesson Classic pre-drilled and tapped K, L, N & X frame
revolvers, including .500)
Remove the rear sight and retain the sight and all mounting hardware for
future use if necessary. Place the insert (10A) into the mount base (10B)
and set both pieces on the revolver as shown below. Install the two 6-48x
.210 screws through the dovetail insert and into the last two tapped holes,
nearest the hammer in the frame of the revolver (Figure 2). Tighten to 20
inch pounds.
6-48x .210 Screws
(Figure 2)
10A Insert
10B Mount
Base
Place the DeltaPoint on the mount base so that the four holes in the bottom
of the DeltaPoint will align with the four short posts on the mount base and
the screw holes in the sight and mount base align (Figure 3), then secure
the sight with the two M4x 0.7mm screws using 20 inch pounds of torque.
(Figure 3)
M4x 0.7mm Screws
Note that the elevation adjustment downward stop is available only when the unit is
installed on a mounting plate. Screwing either adjustment into a stop will lock motion
of the other adjustment.
Elevation
Adjustment
Downward Stop
Do not adjust this screw
Place the sight on the mount base so that the screw holes in the sight and
base align, also the two short corner posts on the mount align to the holes
under the DeltaPoint. The unit may be installed with the mount base keeper
on either side. Install the two M4 x 0.7mm screws and tighten to 20 inch
pounds. Loosen the keeper on the mount. Place the mount on the rail with
the cross bolt located in the desired slot. Check to be sure all the clamping
edges are engaged. Keep a light pressure on the sight toward the muzzle
as you tighten the keeper to approximately 20 inch pounds.
Operating Procedure
Elevation and Windage Adjustment
Warning: Failure to loosen adjustment lock screws before
making adjustments to elevation or windage screws will cause
sight damage. Adjustment lock screws are loosened at the
factory and must be tightened to 4 inch pounds before firing.
Separate controls for the elevation and windage adjustments are found
on the top and left side of the sight. Loosen the two lock screws on the
back side of the sight counterclockwise ½ turn each using the provided
Torx driver. Turn the “D” (DOWN) or “R” (RIGHT) screws with the provided
Torx driver. The windage adjustment
mechanism has limit stops at both ends.
Before shooting, make sure to tighten
the lock screws to 4 inch pounds.
Caution: Boresighting the DeltaPoint
Verify that the magazine of the firearm has been removed or
emptied, and that there is not a round in the chamber. Only
after double checking the firearm, verifying it is empty and safe, should you
proceed with the boresighting process. Be sure to remove the Zero Point®
Boresighter from the the barrel prior to loading the magazine or chamber.
Boresighting the DeltaPoint
The use of a Leupold Zero Point® Boresighter is recommended when zeroing
the DeltaPoint. Due to the low magnification of the DeltaPoint, the grid pattern
will appear relatively small. To make the boresighting process easier, Leupold
recommends placing the eye near the DeltaPoint while making windage/
elevation adjustments. As with any boresighting procedure, be sure to follow
all safety precautions prior to boresighting, and make sure the boresighter has
been removed from the the barrel prior to loading the magazine or chamber.
Illuminated Boresighter
Reversible Cross-Slot Mount
Zeroing the Point-of-Impact
The DeltaPoint windage and elevation screws move the point of impact
60 MOA (15” @ 25 yds) per revolution. Each ‘Mark’ on the adjustment
screws represents about 7.5 MOA of adjustment. There is 60 MOA per
revolution and a total of 8 marks (equals 7.5 per mark). Before shooting,
make sure to tighten the lock screws on the rear of the DeltaPoint (4 inch
pounds, maximum) with the provided Torx driver.
Power On/Off
Warranty Limitation
The DeltaPoint will automatically power on when movement is sensed. The
sight will switch to sleep mode when it remains still for 5 minutes.
There is no other express warranty. Leupold ® hereby disclaims any and all implied warranties,
including but not limited to fitness for a particular purpose. Leupold ® shall not be liable for
incidental, consequential, or special damages arising out of, or in connection with, product use or
performance.
Power-Saving Mode
Leupold Product & Technical Service
Under dark conditions the LED brightness is reduced dramatically to reduce
power consumption. In addition, after the optic has been completely at rest
for 5 minutes the sight transfers to sleep mode, thus nearly eliminating all
battery drain. Upon any movement of the optic, the system powers up the
LED to the appropriate brightness in less than 1/10 of a second.
Placing the included rubber cover over the DeltaPoint forces the unit to
operate at its Lowest ambient light setting and will remain at this level
of operation until either the deltapoint is idle for 5 minutes or longer or
the cover is removed and the Deltapoint adjusts to the current ambient
conditions.
Low Battery Indicator
The DeltaPoint has a unique feature that flashes the aiming point from
maximum to minimum brightness when low battery power is detected. The
operator will have several hours of operating time in this mode before the
sight is rendered inoperable without a battery change.
Intelligent Brightness Control
™
The integrated control circuit adjusts the brightness of the aiming dot /
delta according to ambient light levels. The brightness sensor on the front of
the sight senses the light level in the direction of the target and modifies the
intensity of the dot (•) / delta (▲) accordingly so that it is not overpowering in
low light while remaining highly visible in bright daylight. When moving from
bright to dark conditions, the DeltaPoint will gradually decrease the intensity
of the aiming dot/delta to match the dilation rate of your eye. Be careful not to
obstruct the sensor. Clean if necessary. To ensure immediate functionality,
the light-emitting diode will remain on even in complete darkness but
uses only a small amount of energy. When the optic is completely
stationary for 5 minutes the circuitry switches into sleep mode. It
immediately powers up when any movement or vibration is detected.
Water Integrity
If your Leupold product fails to perform in any way, please contact a Leupold Product Specialist
within our Product Service department to determine if the problem can be solved without sending
the product to Leupold. Many times, the problem can be solved without sending the product to us.
We encourage you to contact us first. Leupold Product Service will assist you with the issue in
the best and most efficient manner. If we do need you to send the product in for service, please
include a note indicating your observations of the problem. Please be detailed in your description,
as it will help us to expedite the service and return your product as soon as possible.
With our On-line Product Service Status feature on our Web site, you can check that your product
arrived, when the service began, when the service was completed, when it was shipped back, and
obtain the UPS tracking number for follow up.
To Reach Leupold Product Service
Phone:
Parcel Service
7:00 a.m. - 4:30 p.m. PST M-F
1-800-LEUPOLD
or (503) 526-1400
Leupold Product Service
14400 NW Greenbrier Parkway
Beaverton, OR 97006-5791 USA
Fax:
Postal Service
24 hours a day, 7 days a week
(503) 352-7621
Leupold Product Service
P.O. Box 688
Beaverton, OR 97075-0688 USA
E-mail:
[email protected]
LEUPOLD, GOLDEN RING, MARK 4, the Golden Ring design, the circle-L reticle logo design, and
various other marks are registered trademarks of Leupold & Stevens, Inc. All marks, including
corporate logos and emblems, are subject to Leupold’s rights and may not be used in connection
with any product or service that is not Leupold’s, or in any manner that disparages or discredits
Leupold, or in a manner likely to cause confusion.
Certain other trademarks used in connection with Leupold products and services are the
property of their respective owners, and are used with permission. BOONE AND CROCKETT
CLUB and BOONE AND CROCKETT are registered trademarks of the Boone and Crockett Club.
NWTF is a registered trademark of the National Wild Turkey Federation. QDMA, and QUALITY
DEER MANAGEMENT are trademarks or registered trademarks of the Quality Deer Management
Association. RMEF and ROCKY MOUNTAIN ELK FOUNDATION are registered trademarks of
the Rocky Mountain Elk Foundation. ADVANTAGE TIMBER and ADVANTAGE TIMBER HD are
trademarks or registered trademarks of Jordan Outdoor Enterprises Ltd. MOSSY OAK BREAK-UP,
MOSSY OAK BRUSH, MOSSY OAK OBSESSION, and MOSSY OAK TREESTAND are trademarks
or registered trademarks of HAAS Outdoors, Inc. A.R.M.S. is a registered trademark of Atlantic
Research Marketing Systems, Inc. The ARD (anti-reflection device) is manufactured by Tenebraex
Corp. under the name KillFlash, which is a trademark of Tenebraex Corp.
We reserve the right to make design and/or material modifications without prior notice.
Copyright © 2011 Leupold & Stevens, Inc. All rights reserved.
Though the DeltaPoint is completely waterproof, extended periods of
complete immersion may result in accelerated battery depletion, possibly
requiring battery replacement. After exposure to salty or dirty water, rinse
with distilled water and dry the sight.
Leupold Full Lifetime Guarantee
Leupold ® warrants its products to be free from defects in materials and workmanship. Leupold ®
will repair or replace, at its option without charge, any product or part found to be defective under
normal use and service. Such repair or replacement shall be the purchaser’s sole and exclusive
remedy under this warranty. This warranty does not include normal maintenance and services
and does not apply to any products or parts that have been subjected to modification, misuse,
negligence, accident, improper maintenance or repair by anyone other than Leupold ®.
The electronics in your Leupold ® DeltaPoint™ Reflex sight are covered by the Leupold ® Electronics
Warranty, and are protected from defects in materials and workmanship for two years from the
date of purchase. In event of a need for service or repair, please contact Leupold Product Service.
Leupold
&
Stevens, Inc.
PO Box 688 Beaverton, Oregon 97075-0688
www.leupold.com
1-800-LEUPOLD
Par t #59828
(538-7653)
Ar twork #59827C