C a t l

Transcription

C a t l

Catalog 2012 - 2013
Sample Preparation
and Laboratory
Consumable Products
CeiExpert
- Accessories for GC & HPLC
- Flash Purification
- Microwave Synthesizer
- TurboVap, Sample Concentration
- RapidTrace, Automated SPE Workstation
- SPE Pressure Manifold
- SPE Vacuum Manifold, SPE Cartridges
- Vacuum Pump
- Sample Preparation for VOC Analysis
- Software for GC & HPLC
- Gas Generator for GC, LC/MS
- Syringe Filters, Membrane Filters
- GC & HPLC Columns
- Vials , caps, septa for GC/HPLC autosampler
- UV-VIS cell for Spectrophotometer
- Electronics Micro Pipettes
- Pipette Tips, Centrifuges, Centrifuge Tubes
- Certify Reference Standard
- High Quality Gas Control Equipment
By : Aijiren Technology Co., Ltd. บริษัท ซี.อี. อินสทรูเมนท (ประเทศไทย) จํากัด
68/876 หมู 8 ถ. รัตนาธิเบศร ต.บางกระสอ
อ.เมืองนนทบุรี จ.นนทบุรี 11000
โทรศัพท 0-2965-8971-3 โทรสาร 0-2965-8974
Email : [email protected]
Web Site : www.cethailand.com
Sample Preparation and Laboratory Consumable Parts
C.E. Instruments (Thailand) Co., Ltd
TurboVap 96
Product of :
Biotage / Sweden
Sample Concentration Workstation
TurboVap Family
TurboVap II
The TurboVap 96 Concentration Evaporator Workstation is a
microprocessor-controlled evaporation system for simultaneous, automated
concentration of multiple samples with unattended operation, convenience
and speed. It can accommodate one or two 96-well microplates or
deepwell plates.
TurboVap 500
The TurboVap II Concentration Evaporator Workstation is a
microprocessor-controlled concentrator used for sample preparation that
provides unattended, automated sample evaporation. The six position
evaporation systems uses a patented gas vortex shearing action and
optical sensors to provide fast and efficient evaporation of organic solvents.
Units may be configured to accommodate either 50 mL or 200 mL
glassware with either 0.5 mL or 1.0 mL endpoint stems.
TurboVap LV
The TurboVap LV Concentration Evaporator Workstation provides
simultaneous evaporation of up to 50 samples. This evaporation system
offers many interchangeable tube racks giving you the flexibility for
automated low volume sample preparation ranging in volumes size from
1.5 mL to 30 mL. The microprocessor-control provides monitoring of the
timed operation and water bath temperature. It also provides automatic
gas shutoff and operational diagnostics.
The TurboVap 500 Concentration Evaporator Workstation is a closed
cell evaporation system that provides automated sample concentration and
solvent recovery using a helical gas flow and sensor endpoint detection
technology. The “helical flow” of air is created by a motor-driven fan. The
solvent vapors rise and enter the condenser, condense on the side walls,
then run out the drain into a suitable waste or reclamation container. The
two position unit accommodates 500 mL vessels with either 0.5 mL or 1.0
mL endpoint stems. Biotage delivers the most efficient and rapid solvent
evaporation systems for chemistry laboratories around the world.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Web site : www.cethailand.com
page : 1
V-10 Evaporator
Product of :
Biotage / Sweden
RapidTrace Automated SPE Workstation
V-10 Evaporator
Vortex and vacuum evaporation system
Quickly and safely dry dissolved compounds
Automated Solid Phase Extraction Workstation
Advanced bioanalytical techniques such as LC/MS/MS and GC/MS
meet the increasing demand for greater speed. In many laboratories,
solid phase extraction (SPE) has then become the throughput limiting
step. The RapidTrace+ eliminates manual sample processing
bottlenecks so that analysts can realize the full benefits of today’s
powerful analytical instruments. RapidTrace+ is the perfect compliment
to highspeed analytical techniques, a powerful high-throughput
workstation dedicated to unattended automated sample preparation. .
The Biotage V-10 solvent evaporation system rapidly dries samples
dissolved in both aqueous and organic solvents up to 20x faster than
traditional rotary or centrifugal evaporators, leaving solvent-free product in
the vial. This innovative vortex and vacuum evaporation technology was
developed through collaboration with major pharmaceutical companies. The
high performance vacuum capability of the V-10 allows low temperature
evaporation of high boiling solvents. Optimized evaporation methods
protect the sample against bumping and overheating. Versatility and
scalability eliminate handling and reformatting issues.
SPE Dry 96 Sample Concentrator system
Pressure+ 48, +96 SPE Pressure Manifold
Sample Concentrator system for 96 Wellplate
Pressure Manifold for Solid Phase Extraction
Biotage® PRESSURE+ manifolds deliver positive pressure, parallel
processing for 96 well plates, 1 mL 3 mL and 6 mL column formats. The
systems utilize a consistent, uniform flow of positive pressure to move both
low and high viscosity liquids through SPE plates and columns. Each port of
the PRESSURE+ manifold independently maintains constant pressure,
increasing the overall reproducibility of analyte recoveries. This unique
design allows for partially populated racks to be used without sacrificing
extraction efficiency. Tel : 0-2965-8971-3
Fax : 0-2965-8974
Designed for high throughput laboratories, the SPE Dry 96 and SPE Dry 96
Dual Sample Concentrator Systems provide efficient solvent evaporation in
microplate format and are compatible with 24-, 96- and 384-well collection
plates. Heated gas flow from above and below the collection plate ensures
efficient solvent evaporation. An easy-to-use front panel display allows
accurate temperature programming and gas flow control. The systems are
supplied as standard with stainless steel needles and are also available
with PTFE-coated needles for applications using aggressive solvents, acids
and bases. Biotage delivers the most efficient solvent evaporation
laboratory equipment for method development, sample extractions and
much more.
page : 2
Isolera Prime Flash Purification
Product of :
Biotage / Sweden
Initiator+ Microwave Synthesizer
The Biotage® Initiator+ represents a new generation of
instruments for organic, medicinal, materials, nano and polymer
chemistry professionals. It is an upgradeable and reliable platform for
chemists to make great discoveries. The Initiator+ is a flexible system
that utilizes all Biotage vials, from 0.2 to 20 mL, in any order or
combination, at any time without system modifications, delivering greater
flexibility and direct scale-up from milligrams to grams. Initiator+ can
also be upgraded with automation solutions to achieve higher
throughput to save time and cost.
Initiator+ SP Wave Microwave Peptide
Synthesizer
Isolera Prime is the new standard in value-priced flash purification
systems delivering a full range of features and cost-saving benefits. This
flexible system is upgradeable and grows with the needs of laboratories and
universities where value is especially important.
Isolera Prime is compatible with Biotage flash cartridges, including the
new value-priced Biotage ZIP. Isolera Prime is the newest addition to the
acclaimed Isolera automated flash system family, specifically designed for
chemists needing an automated purification platform to increase
productivity delivering high value and just the right features.
Isolera Flash Purification
Isolera, a compact flash purification system with intelligent features,
The Biotage® Initiator+ SP Wave is a programmable
synthesis system that can be configured to perform either microwave
assisted peptide or organic synthesis.In peptide synthesizer mode, this is
the perfect tool for chemists synthesizing peptides and peptidomimetics,
including difficult modifications and labelling of sequences, by using single
or multi-step procedures. The intuitive Initiator 4.0 software controls the
instrument functions and by using the pre-defined methods synthesis can
be started immediately. enables chemists to easily achieve better separations. The patented TLCto-gradient feature automatically creates elution gradients and suggests
cartridge and sample size. Collect fractions using two wavelengths, adjust
the flow rate from 1 to 200 mL/min as needed and use up to four solvents in
a single gradient, for maximum purity and yield.
Isolera is available in a single cartridge base model, the Isolera One, and
a 4-cartridge configuration, the Isolera Four, which is ideal for multi-user or
high-throughput laboratories.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 3
AFFINILUTE™ MIP Analytical SPE Products
Product of :
Biotage / Sweden
Biotage® AFFINILUTE MIPs
are a range of SPE phases that offer
analytical chemists ultimate selectivity
compared
with standard solid phase
extraction techniques. ISOLUTE QuEChERS
ISOLUTE QuEChERS contain a mixture of precisely measured
chemical compounds as described in the AOAC and EN standard methods
for the analysis of pesticide residues from fruit and vegetable samples.
Unlike labor intensive liquid-liquid extraction and complicated solid phase
extraction methods, QuEChERS combines clean extracts with rapid work
flow and ease of use that ensures reproducibility and faster sample
preparation. Biotage’s strict quality control during the manufacturing
process ensures consistent performance in an already well defined
methodology.
ISOLUTE SPE Products
AFFINILUTE SPE MIP products are a range of highly selective SPE
phases based on molecularly imprinted polymers. Unlike other methods,
Biotage AFFINILUTE MIP products rely on the specific molecular structure
of the analyte for targeted capture resulting in exceptional clean up. Biotage
AFFINILUTE MIP combines high affinity with standard flow through sample
preparation methodology.

Lower detection limits due to cleaner extracts

High selectivity based on the structure of the analyte of interest

Reduced matrix effects and ion suppression as interferences
can be washed from the columns using stringent conditions.
AFFINILUTE MIP products are offered in a standard 3 or 10 mL off-line
SPE format. All products are delivered with a data sheet, describing the
extraction methodology in detail and a quality assurance report.
Application :
Residual Extraction for :
» – ß-Agonist
» – ß-Blocker
ISOLUTE SPE products are a range of leading quality SPE
» – Amphetamines
columns and 96-well plates, packed with a variety of ISOLUTE nonpolar, mixed-mode and ion exchange sorbents.
» – Chloramphenicol
» – Clenbuterol
» – Fluoroquinolones
Designed to extract drugs from biological fluid samples, a range of
retention mechanisms are available, along with technical notes that
detail how to use each sorbent type.
All ISOLUTE SPE sorbents are available packed into standard or tabless SPE columns, ideal for many manual and automated SPE
procedures. For higher throughput applications, industry standard fixed
well ISOLUTE-96 extraction plates, or versatile ISOLUTE Array® wells
and plates are available. ISOLUTE Array plates can be populated with
up to 96 individual Array wells, to match the number of samples to be
extracted.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
» – Nitroimidazoles
» – NNAL
» – NSAIDs
» – PAH
» – Triazine
» – TSNAs
page : 4
Product of :
DBS Instrument / Italy
Whisper 1/Whisper 2 Nitrogen Generator
Whisper 1 / Whisper
2 Nitrogen Generator
with Air Compressor
Gas Generator for GC, LC/MS
Whisper- 0, Nitrogen Generator
Purity 98 to 99.5%
Whisper-0 Nitrogen
Generator without Air
Compressor
The Whisper 1/ Whisper 2
nitrogen generator has been
developed to meet specific
requirements in terms of flow,
purity and pressure in LC-MS
applications. It can be used for
evaporation of solvents in
samples being analysed. The
simple high efficiency membrane
technology allows the separation
nitrogen from the other
of
components the compressed.
Purity 98 to 99.5%
The Whisper-0 nitrogen generator
has been developed to meet
specific requirements in terms of
flow, purity and pressure in LCMS applications. It also be used
for evaporation of solvents in
samples being analysed. The
simple high efficiency membrane
technology allows the separation
of nitrogen from the other
components of compressed air
inlet. The low pressure drop, just one bar, allows the unit to be connected to
an existing dry and oil-free compressed air source in the lab.
The low pressure drop, just one bar, allows the unit to be connected to an
existing dry and oil-free compressed air source in the lab.
Membrane separation technique
Compressed air is forced through a hollow fiber membrane, with
selective permeation of the different components - nitrogen, oxygen,
CO2, water vapour and traces of rare gases - depending on the rate of
diffusion. The rate of diffusion of nitrogen trough the membrane is
slower than the other components, which thus flow outside of the fiber
membrane, leaving just nitrogen inside; this is then discharged
subsequently, ready for use.
Membrane separation technique
Compressed air is forced through a hollow fiber membrane, with selective
permeation of the different components - nitrogen, oxygen, CO2, water
vapour and traces of rare gases - depending on the rate of diffusion. The
rate of diffusion of nitrogen trough the membrane is slower than the other
components, which thus flow outside of the fiber membrane, leaving just
nitrogen inside; this is then discharged subsequently, ready for use.
Ordering Information
LC-MS N2 Generators (with internal compressor)
With Air Compressor 220V – 50Hz
Model
N2-Whisper-2-50
N2-Whisper-1-50
Flow
Up to 35 l/min of Nitrogen
LC-MS N2 Generators (without internal compressor)
Model
N2-MiniWhisper
N2-Whisper-0-40
N2-Whisper-0-80
N2-Whisper-0-120
Tel : 0-2965-8971-3
Flow
Fax : 0-2965-8974
page : 5
Product of :
DBS Instrument / Italy
Ultra Zero Air Generator Series GT
Gas Generator for GC, LC/MS
NM-H2 Hydrogen Generator
NMH2 Series Generator
Purity : 99.99999%
The NM-H2 Hydrogen Pure Gas
Generators from DBS employ
the newest membrane technology
available for electrolytic
production of pure hydrogen
gas, including exclusive no
maintenance auto-drying
technology.
GT Ultra Zero Air Generators
1500 ml/min - 3000 ml/min - 6000 ml/min - 15000 ml/min - 30000 ml/min
The DBS Ultra Zero Air Generators produce laboratory grade purified air
for the most accurate and convenient calibration of testing equipment.
Designed with safety and convenience in mind, this system will generate
purified air from an existing in-house oil-free compressed air supply,
eliminating the need for inconvenient high-pressure gas cylinders.
Eliminating gas cylinders reduces annual operating costs associated with
materials, labour, and down-time, and reduces risk of injury to workers.
The patented DBS NM-H2 series of No Maintenance Hydrogen Generators
is ideal for operation with gas analysers, as fuel gas for flame tools, all kind
of carrier gas applications, such as GC and GC-MS (Mass Spectrometry),
or as a source of pure hydrogen in plasma chambers and other isolated
environments.
Features and Benefits
•
•
•
•
•
•
•
•
•
•
LCD display shows set points, operating conditions and status
Continuous or intermittent operation
Visual operating status lights
Alarm conditions
Flow indication. Informs the operator at a glance that hydrogen gas is
flowing at the specified rate
Bi-directional RS232 interface
Selectable auto start
Remote control (optional)
Cascading of 2 or more units (optional)
CE Mark and CSA compliant
System Components
The DBS Ultra Zero Air Generators will remove CO and HC pollutants to
less than 0.1 ppm, and NOx contaminants to 1 ppm. Carbon dioxide is also
removed to about 1 ppm levels. Operation of the generator requires low
levels of air consumption and electrical power. This complete turnkey
system is engineered with the highest quality components, is easy to install,
and requires only minimal annual maintenance.
Ultra Zero Air Generators GT (1.5 - 30 l/min)
Purity: <0.1 ppm HC, <0.1 ppm CO, <5 ppm CO2, <0.1 ppm NOx,
Hydrogen generators NM series
Purity: > 99.99999 % H2 out pressure 10bar
Model
Flow ( pressure out 0.1 - 10 bar)
NM-H2 100
100 cc/min of Hydrogen
NM-H2 160
NM-H2 250
NM-H2 300
NM-H2 500
NM-H2 600
NM-H2 1000
Model
Flow
N-GT1500
1.5 l/min Ultra Zero Air, with Automatic Controls
N-GT3000
N-GT6000
N-GT15000
N-GT30000
Consumables
N-FIL001
Filter housing complete with Filter cartridge (external)
N-CART001
Replacement cartridge for Inlet filter
N-FIL002
Filter for Zero Air Generator (internal)
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 6
Product of :
HAMILTON / USA, Switzerland
MICROLAB 600 Dispenser
There are three different dispenser models
available from the Microlab 600 family. Each dispenser is
based on a positive displacement system that provides better than 99% accuracy,
independent of a liquid’s viscosity, vapor pressure, and temperature.
HPLC Columns
Single Syringe Dispenser
The Single Syringe Dispenser is ideal for dedicated
dispensing applications requiring a single syringe
drive. Improve accuracy, throughput, and
consistency when compared to traditional laboratory
equipment like serological and repeating pipettes.
Hamilton manufactures both silica-based and polymeric HPLC columns,
providing a wide range of column retention selectivities and performance benefits.
Hamilton's polymeric HPLC columns combine the inertness and pH stability of
polymeric supports with the pressure stability and durability of silica-based columns.
Column packing materials are available for reversed phase, anion exchange, cation
exchange, and ion exclusion separations
Dual Syringe Dispenser
The Dual Syringe Dispenser has two syringe
drives for applications such as Animal Dosing
that require the use of more than one liquid at
the same time. In this application the "No
Drug Control" is primed into one syringe
while the "Test Drug" is primed into the other
syringe. The two liquids can be dosed from
the same instrument saving setup and dosing
time.
Reversed Phase
PRP-1
General purpose pH stable long life column,
synthesized DNA
Gradient peptide and protein separations
Long life column for LC/MS applications, synthesized
DNA, and small molecule
Reduced system pressure for protein and peptide
separations and enhanced oligonucleotide recovery
Nonporous support for very fast gradient separation of
large proteins
General purpose silica-based reversed phase
PRP-3
PRP-h1
PRP-h5
PRP-Infinity
HxSil C8, C18
Continuous Dispenser
The Continuous Dispenser is designed for
time critical applications requiring repetitive
dispensing. One syringe fills while the other
syringe dispenses so the instrument is always
ready. Perfect for integration into semiautomated or fully automated manufacturing
lines.
Anion Exchange
PRP-X100
Anions, inorganic and organic using conductivity or UV
detection. 0 to 100% solvent compatible
Similar to PRP-X100 but for lower level anions (20 ppb
to 20 ppm)
Gradient separation of large proteins and labeled DNA
Gradient separation of labeled and unlabeled DNA
Isocratic or gradient separation of carbohydrate
oligomers up to DP8
Gradient separation of complex carbohydrates
PRP-X110
PRP-X500
PRP-X600
RCX-10
RCX-30
MICROLAB 600 Diluter
The MICROLAB 600’s
Dual Syringe Diluter
Cation Exchange
PRP-X200
PRP-X400
PRP-X800
HC-40
HC-75 Ca2+
HC-75 H+
HC-75 Pb2+
Inorganic and organic cations using conductivity or UV
detection. Separate mono or divalent cations depending on
mobile phase conditions.
Glyphosate and metabolite in drinking water. Also unique
hydrophilic interaction separations
Mono and divalent cations in the same run. Transition metals
Sugar oligomers up to DP8. Max pressure 1,000 psi
Mono and disaccharides in corn syrup. Max pressure 1,000 psi
Organic acids and sugars. Max pressure 1,000 psi
Sugar alcohols. Max pressure 1,000 psi
create up to a 1:50,000 dilution in a
single step, drastically reducing
preparation time and wasted buffer.
The diluent washes the tubing between each sample, minimizing carryover for even
the most sensitive techniques, including:
 Atomic Absorption (AA)
 Inductively Coupled Plasma Spectroscopy (ICP)
Ion Exclusion
PRP-X300
configuration uses two syringes to
 High Performance Liquid Chromatography (HPLC)
 Gas Chromatography (GC)
Organic acids and alcohols
 Liquid Scintillation
Polymeric Column Benefits
Hamilton's polymeric HPLC columns combine the inertness and pH stability of
polymeric supports with the pressure stability and durability of silica-based
columns. Column packings are available for reversed phase, anion exchange,
cation exchange, and ion exclusion separations. There are a total of 19 different
packings.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 7
Product of :
HAMILTON / USA, Switzerland
SofTouch Pipette
SofTouch pipettes provide a total
ergonomic solution to repetitive or
critical pipetting tasks. With an ultra
lightweight and ergonomic design,
SofTouch pipettes increase
throughput while simultaneously
reducing the workload and the risk of
repetitive stress injuries. All piston
movements are driven with a fast,
highly precise DC-motor, virtually
eliminating all forces on the hand and
thumb. Single and Multi-channel
available.
SoftGrip Pipette
The SoftGrip pipette sets new standards in
pipette technology with its award-winning,
innovative design. Using our expertise in precision
fluid measurement, we've developed the highest
quality pipette with an emphasis on minimizing the
hand strain, fatigue and injuries caused by other
pipettes.Single and Multi-channel available.
SoftGrip Fixed Volume Pipette :
P/N 55019-01
P/N 55019-03
P/N 55019-05
P/N 55019-07
P/N 55019-09
P/N 55019-011
P/N 55019-013
P/N 55019-015
P/N 55019-017
P/N 55019-019
SoftGrip Fixed Volume 5ul
SoftGrip Adjustable Volume Pipette :
P/N 55019-30
P/N 55019-32
P/N 55019-34
P/N 55019-36
P/N 55019-38
P/N 55019-40
SoftGrip Adjustable Volume 2ul
SofTouch Single Channel
P/N 8707-01EU
P/N 8707-02EU
P/N 8707-03EU
P/N 8707-04EU
SofTouch 8 Channel
P/N 8707-05EU
P/N 8707-06EU
P/N 8707-07EU
P/N 8707-08EU
P/N 8707-09EU
P/N 8707-10EU
P/N 8707-11EU
P/N 8707-12EU
SofTouch 12-CH 10uL EU
SofTop Dispenser
The SofTop Quik Dispenser
for adjustable volume bottle top
dispensing. It offers maximum
chemical and thermal
resistance with innovative
ceramic plunger. Available in
six different volumes from 0.2
mL to 60 mL.
SoftGrip 8 Channel 50ul
SoftGrip 12 Channel Pipette :
P/N 55019-54
P/N 55019-56
SofTouch 12 Channel
SoftGrip 8 Channels Pipette :
P/N 55019-50
P/N 55019-52
SofTouch Single 10uL EU
SoftGrip Fixed Volume Pipette :
AdvanTip™ Pipette Tips
P/N 51249-01
P/N 51249-10
P/N 51249-20
P/N 51249-30
P/N 51249-50
P/N 51249-60
High quality tips for the best
accuracy and precision, extensive
universal tip selection for optimal
performance, and multiple
packaging options to meet
laboratory requirements.
SofTop 0.2 – 1 ml
SofTop 2.0 – 10 ml
SofTop 0.4 – 2.0 ml
SofTop 10.0 – 60.0 ml
Syringes
SoftAide Pipette
The SoftAide PIpette
Controller delivers ergonomic
comfort for high-precision serial
pipetting. For use with glass
and plastic standard pipettes
from 100 uL to 200 mL.
Hamilton Company
manufactures a complete range
of syringes for partial loop
filling, complete loop filling, and
reverse loop filling by the
aspiration HPLC technique.
Syringes for a complete range
of GC applications, including:
capillary and packed column methods; on-column and split/splitless
injection techniques; use of Merlin MicrosealT and JADE injectors; and
headspace sampling protocols.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 8
Product of :
Allsheng / China
Features:
Nano-100 Micro Spectrophotometer
Nano-100 is a MicroSpectrophotometer
designed for nucleic acid
measurements.
It can accurately measure nucleic
acid samples, and doesn't need to
dilute high-concentration samples.
Simply pipette 0.5~2ul sample
onto the pedestal , laying down
the sampling arm, Nano-100 can
automatically complete the
measurement within 5 seconds.
1. Direct, easy measurements in less than 5 seconds
2. Require only 0.5~2ul samples
3. No cells or cuvettes and no warm up
4. Optional data output via built-in printer, SD-RAM Card, USB memory
5. Touch screen and panel operation, without computer
6. No dilutions for samples
Code
AS-11030-00
AS-11040-00
Description
Nano-200-H Xenon flash lamp's long life >109 flashes
Nano-200-A Xenon flash lamp's long life >108 flashes
Bioprep-24 Homogenizer
.
Features:
1. Direct ,easy measurements in less than 5 seconds-just pipette&wipe
2. Fullspectral output
3. Measures DNA,RNA (A260) and protein (A280),concentrations and
sample purity(260/280 ratio)
4. Large concentration range without dilutions
5. User-friendly software that includes Custom Methods and data export
capabilities.
6. Low-cost operation -no plates or other consumables.
Code
AS-11010-00
AS-11020-00
Description
Nano-100-H Xenon flash lamp's long life >109 flashes
Nano-100-A Xenon flash lamp's long life >108 flashes
Nano-200 Micro Spectrophotometer
Nano-200 Nucleic Acid
Analyzer
Nano-200 is a Nucleic Acid
Analyzer designed for
analyzing the concentration
and pure of Nucleic Acid
(DNA/RNA).
Simply pipette 0.5~2ul sample
onto the pedestal, laying down the
sampling arm, Nano-200 can
automatically complete the
measurement within 5 seconds.
Fax : 0-2965-8974
enzymes, etc. from very tough samples while still retaining molecular
integrity.
Fast, effective and reproducible homogenization of a
wide range of samples, including hard to lyse tissues and cells. It also holds
extraordinary powerful for the processing of even impact resistant samples
such as bones or cartiage.
Features
1. 3D Rotating High Speed Motion" for quick disruption of those fibrous
tissues and resistant cells
2. 10 Programmable memory settings and user optional condition
settings
3. A wide range of rotation speed settings from 4,000 rpm to 5,800 rpm,
increment 100 rpm
4. Brushless motor realizing no brush particle generation and no brush
replacement
5. Easy to remove sample tube holder and easy to fix sample tubes
with the turn of the central knob
6. Easy to monitor the disruption process through the clear lid
7. Simultaneously homogenize either 24x2ml or 12x5ml tubes
8. Disposable tubes ensure no threat of cross-contamination
9. Economical and compact tabletop system
Typical Samples
- Human, animal, plant cells
- Micro-organisms
- Soil and sediments
- Swabs and feces
- Drugs, polymers, lotions, etc.
Code
AS-13010-00
Tel : 0-2965-8971-3
The Bioprep-24 is an ideal solution for releasing DNA, RNA, proteins,
Description
Bioprep-24 AC100~240V 50/60Hz
page : 9
Product of :
Allsheng / China
Mix Smart model MIX-100
Dry Bath Incubator Model MK-20
Temp. Control Range:
-10 °C to 100 °C
Features
The Dry Bath Incubator is a
microprocessor-controlled product
using advanced thermoelectric
technique. With this technique,
more stable and accurate
temperature control is achieved.
Replacement is convenient with
optional metal modules of various
specifications configured for
different types of test tubes.
1. LCD display. It easy to setup and use
2. Simultaneous display of set and actual time, temperature
3. As it is equipped with various optional blocks, the instrument can adapt to
different tubes & wells to cope with experimental needs. It is easy to
replace the metal blocks and is very simple to clean and sterilize.
Customized blocks are available to suit your specific demands
4. Reliable design with inner extra temperature protection
5. Heave of the block makes block change easy and convenient
6. Temperature deflection adjusting meet with different demands
7. Microprocessor controlled incubation time and temperature.
8. Beep-signal / Stop after program completion
9. Conforms to CE safety standard
Compact and amazingly designed, benchtop. Mix-Smart can be used for
virtually any mixing applications. It accommodates micro test tubes, PCR
plates, deepwell plates and MTPs. It features an integrated vortexing
function and an operating concept that is as simple as it is intelligent.
The Mix-Smart only takes up an area of 17 x 24 cm, less than the size of
this A4 paper. But the Mix-Smart can be offered many options for holding a
wide variety of tubes and plates:
Product Features：
Mixing in a 3-in-1 format
1. Plates (up to 96- and 384-well formats)
2. Tubes 0.2 ml upto 50 ml
3. Vortexing numerous tube formats (e.g., 15 ml and 50 ml conical tubes)
Turbo Thermo Shaker, TMS 200 / TMS 300
Mixing Speed: 300 to 3,000 rpm (Increment: 10rpm)

Touch vortexing Speed: 3,500 rpm

Adjustable mixing time: 15 s to 99h59min; continuous

Mixing and vortexing radius: 1.5 mm (3 mm mixing Orbit)
One Device -- one package!
.
TMS-200 : Orbit: 2mm, rpm 300-2000 rpm, Temp +5 RT to 100 °C
TMS- 300 : Orbit 3mm, rpm 300-3000 rpm, Temp +5 RT to 100 °C
The TMS-200/TMS-300 Turbo Thermo Shaker can be
adjusted to every aspect of the mixing process. Homogeneity and
attunement of impulse, direction and amplitude created a maximum
resonance effect that provides optimal mixing according to wetting are
laminated. The Turbo Thermo Shaker comes with a large precision heat
surface, witch can be regulated in 0.1°C increments up to staggering
100°C. Exchangeable heating blocks modules and holders fit special tubes,
vials and micro plates. Programmable soft-keys provide for practical usage.
The Tubro Thermo Shaker is slim, quiet and efficient. Its Anti Vibration
Technology buffers all unwanted vibrations of its work environment.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
MIX-100 comes standard with five tube holders:
1. 96x0.2ml PCR Tube Holder
2. 24x0.5ml Tube Holder
3. 24x1.5/2.0ml Tube Holder
4. 8x15ml Tube Holder
5. 3x50ml Tube Holder
page : 10
Incubator Model MK-100-2A
Product of :
Allsheng / China
The Incubator MK100-2A
is a high performance microplate
incubator which accommodates up
to two microplates. The MK100-2A
can be used for any enzyme or cellbased assays requiring uniform and
strictly
Thermo Shaker for Microtubes, MSC-100
Designed for simultaneous
heating and cooling and mixing
of small samples, the MSC-100
are supplied with
interchangeable platforms for
microtubes. Mixing and heating
and cooling modes can be used
both simultaneously and
independently, i.e. the device
can work as a shaker and as a
thermostat.
The main body of the Mixing Block can be used with different kinds of
blocks.
Orbital Shaker model OS-100
OS-100 Orbital
Shaker is a powerful
variable speed shaker
which provides efficient
orbital motion. Speed and
time are under
microprocessor control. The shaker can be applicable in different laboratories: in microbiology,
chemistry, immunology, biochemistry, and molecular biology.




Digital speed control,
Speed range 50-300 RPM
Orbit 10 mm
Digital timer 1min – 99h59min
Orbital Shaker model OS-200
OS-200 Orbital
Shaker is a powerful
variable speed shaker
which provides efficient
orbital motion. Speed and
time are under
microprocessor control.
The shaker can be applicable in different laboratories: in microbiology,
chemistry, immunology, biochemistry, and molecular biology.




Digital speed control,
Speed range 50-300 RPM
Orbit 10 mm
Digital timer 1min – 99h59min
Tel : 0-2965-8971-3
Fax : 0-2965-8974


Temperature control incubation from +8 °C RT up to 70°C
Platform capacity: 2 microtest plates
Mini Centrifuge Model Mini 13K/Mini 14K






Extremely quiet operation
Easy-to-follow LCD display
Capacity: 12 x 1.5/2.0ml tubes
Separate short-spin key
Low sample heating (only 12°C
after 30 min, at max. speed)
Autoclavable rotor (121°C,
20min)
Thermo Shaker Incubator Model MB100-4A
The MB100-4A is designed for
shaking 1-4 standard 96-well plates
in the thermostating mode. It
is designed using the multi-principle
which allows using it as 2
independent devices:
1. Incubator for lasting incubation
without shaking of micro-quantities
(insect, plant cell cultures, etc.) in
immunoplates.
2. Microplate thermo-shaker for
immunochemistry and molecular
diagnostics, where the requirements
to the result reproducibility and thus
to the precise method regulation are
particularly high. A distinctive feature for the MB100-4A is two-side heating of microtest
platesthat allows achieving exact correspondence of the set and actual
temperature in wells of the microtest plates.
page : 11
Sample Concentrator Model MD200-2
Product of :
Allsheng / China
Sample concentrator Model WD-12
. The instrument consists of a
base and stand assembly, sample
holder and gas distribution
system. Test tubes are held in
place by a spring-loaded sample
holder and support tray. Each
position is numbered. The gas
passes through an adjustable flow
meter to the distribution manifold.
Flexible tubing leads to valve-tube
assemblies at each position. Depending on the test-tube size and solvent volume they can be
individually raised or lowered to the correct height. Needles blow gas onto
the surface of the solution resulting in rapid evaporation of the solvent. All
materials used are laboratory quality and can withstand contact with organic
solvents.
The round, stainless steel water bath is thermostatically controlled and will
accurately maintain water temperature from ambient temperature to 99Ԩ.
Sample Concentrator Model MD200-1
Dual Heat Block
The instrument consists of a base and stand assembly, sample holder and
gas distribution system. Test tubes are held in a block . The gas at 5 to 10
psig passes through the distribution manifold. Depending on the test-tube
size and solvent volume they can be individually raised or lowered to the
correct height. Needles or glass pipets blow gas onto the surface of the
solution resulting in rapid evaporation of the solvent. All materials used are
laboratory quality and can withstand contact with organic solvents. Acid
resistant models are available for corrosive application
Sample Concentrator Model MD200-1A
96 Wellplate Heat Block
Single Heat Block
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 12
MTV-100 Multi-Tube Vortexer
Product of :
Allsheng / China
.
ID Card Incubator Model KD37-24
Digital incubator for the
Gel cards.
The K37-24 ID-incubator holds 2
independent incubation zones
with a capacity for 12 Gel cards,
and user can set temperature
and incubator time. It can be
suitable many types ID-CARDS
from different manufacturers.
Features
Pulsing mode: Programmable pulsing mode allows user to adjust the pulse-on
and pulse-off times between 1~59 seconds in 1 second intervals. This feature
enhances the vortex action by creating a more vigorous mix.
1. Incubator for 24-Gel Cards in racks at 37°C
2. 2 independent incubation zones with a capacity for 12 Gel cards
3. Digital interface screen for control and visualization of remaining
incubation time and real temperature for each zone.
4. Fixed pre-set temperature of 37 degree
5. Pre-set incubation time of 15 minutes, which can be adjust by the user
6. Audible programmable alarm to notify end of incubation period
Microprocessor control: The variable speed microprocessor control provides
consistent uniform mixing action.
LCD display: Touch pad controls with easy-to-read, independent LCD displays
for speed and time allow operator to view
both settings at once.
Applications: Suspensions, high throughput testing in clinical, environmental,
and chemistry labs, use
for QuEChERS sample preparation
Specification
1.
2.
3.
4.
5.
Capacity: 24 Gel cards
Temperature: 37°C
Timer: 15min (Variable)
Power: AC220V or AC120V 50-60Hz, 300W
Dimensions: D x W x H = 380x220x115 mm
Denaturation & Hybridization System
.
Programmable system and
humidifying that automates the steps
in a slide-based FISH procedure, and
provides walk-away convenience for
clinical and research personnel. The
low cost unit accepts a wide range of
sample types, is easy to use, and
reduces hands-on time by more than
50% while ensuring overall precision
and accuracy in all FISH assays. Bacti-Cinerator Sterilizer model HM-3000A
.
The Bacti-Cinerator
Sterilizer Sterilizes microorganisms
utilizing infrared heat produced by a
ceramic core element. The ceramic
element contains no asbestos and
ensures maximum sterility without
splatter across the work surface area.
Complete sterilization occurs within 5-7
seconds at optimum sterilizing
temperature of 1500ºF (815.6ºC).
The small footprint makes the Bacti-Cinerator Sterilizer an ideal instrument
for anaerobic and aerobic chambers alike. Several user friendly accessories
are also available for the Bacti-Cinerator sterilizer
Features
1. Sterilizes needles, loops, and culture tube mouths in five to seven
seconds at optimum sterilizing temperature of 815.6°C (1500°F)
2. Ceramic funnel tube enclosed in stainless-steel perforated guard and
stainless-steel support stand
3. For AC220V 50/60Hz
Specification
1. The center high-temperature: 815±50°C
2. The Max-diameter of sterilizer goods: φ14mm
3. The length of sterilizer: 140mm
4. Net weigh: 1.3Kg
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Up to 12 slides can easily be added or removed with one hand. Two-side
heating of slides that allows achieving exact correspondence of the set and
actual temperature and maintaining uniform temperature across all slide
positions.
Features
1. User Programmable Settings
 Touch screen allows for easy to read and easy programming
 99 user programmable settings
 Three operation modes: denaturation/hybridization, hybridization and
fixed temperature
 Can be used as a fixed temperature slide warmer
2. Easy to use
 Eliminates manual steps and reduces hands-on time during FISH
procedures
 Slides do not need to be fully loaded to maintain temperature accuracy
 Slide guide keeps slides in place and allows for one hand removal
 More stringent temperature control
page : 13
Product of :
Kirgen Inc./USA

Authorized by ISO 13485 certification.

Unique thin-walled design increased the flexibility of pipette tips for
convenient operation and precision, effectively reduced the risk of RSI.
Microcentrifuge Tubes 0.65, 1.5, 2.0ml

Flexible tail vertebrae, enhance sealing between pipette and tips Unique
conical design, fits most pipette brands (Eppendorf, Gilson, Biohit, Thermo,
Labsystems etc.)
Clear graduation, easy to observe
Uniformity and hydrophobicity of tip surface minimize the liquid residual
The gradually pointed design is perfectly suitable for micro-liquid pipetting

Extra-long tips
Greatly reduces the cross contamination between pipettor and tips
Greatly reduces the cross contamination between samples and pipettor
Reduce the times to sterilize the pipettes to extend service time
Reduce the time and cost for pipette sterilization
The extra long design is convenient for pipetting of test tubes, culture bottles
and volumetric flasks
Clear and precise graduation, easy for observation
Kirgen microcentrifuge tubes are made from high quality PP
materials with extensive chemical compatibility; Atutoclavable and sterilized
Withstand a max centrifugal force to 25,000×g, DNAse/RNAse free, non
pyrogens. No release agent and surface coating used in production
process. Ultra-smooth inner wall to reduce sample attachment. No heavy
metal element and organics contained in colorful tubes.








Bevel design of tube cap edge, good touch, easy to open
Lock design to ensure leak proof.
High quality raw materials, ultra-clear wall, easy to observe
Clear and precise graduation for easy identification
Unique semi-closed function, reduce the number of sample
contamination caused by operation
Frosted writing area on the side of the tube, easy for labeling
Conical bottom, fits most centrifuge motors
Available sizes : 0.65ml, 1.5ml and 2.0 ml
Product
Description
Packing
KG 1111
KG 1121
KG 1131
KG 1151
KG 5131
KG 5111
KG 1313
KG 1323
KG 1333
KG 5333
KG 5313
0.5-10ul, clear, graduated
0.5-10ul, clear, graduated, rack pack
0.5-10ul, clear, graduated, sterile, rack pack
0.5-10ul, clear, graduated, refill pack
0.5-10ul, clear filter tips, graduated, sterile, rack pack
0.5-10ul, clear filter tips, graduated,
100-1000ul, blue, graduated,
100-1000ul, blue, graduated, rack pack
100-1000ul, blue, graduated, sterile, rack pack
100-1000ul, blue filter tips, graduated, sterile, rack pack
100-1000ul, blue filter tips, graduated
1000/box
96/rack
96/rack
480/rack
96/rack
1000/box
1000/box
96/rack
96/rack
96/rack
1000/box
Universal Fit Pipette Filter Tips
Kirgen universal fit filter tips fit
in experiments with aerosol contamination and provide
unsurpassed performance in applications in cell culture,
bacteriology, virology, molecular biology, radioactive
samples; especially suitable for infective and dangerous
samples such as pathogenic microorganism, virus etc.
Micro Centrifuge Tube
KG2111
KG2211
KG2911
0.65 ml microcentrifuge tube, clear, graduated, 1000/box
 The filters are made from highdensity polyethylene, no
adhesive and PCR inhibitor contained, effectively
reduce cross contamination and protect users.
 Hydrophobic raw materials protect the pipettes from contamination and avoid
sample losing.
 Multiple packages available to meet your different requirements: bag pack, rack
Universal Fit Pipette Tips
pack (non sterile), rack pack (sterile), refill pack (sterile) etc.
 RNAse/DNAsefree
Kirgen universal fit pipette tips are
automatically manufactured from 100% medical grade
polypropylene with five star high precision mold in
100,000 grade clean room, guarantees precise
pipetting and uniformity of tip surface; no additive and
release agent are used during production, all tips are
DNAse/RNAse free, non pyrogens and autoclavable;
the unique design of extended length greatly reduces
cross contamination. Tel : 0-2965-8971-3
Fax : 0-2965-8974
Product No.
KG 5232-L
KG 5212-L
KG 1212
KG 1222
KG 1232
KG 1252
KG 5232
KG 5212
Description
1-100ul filter tips, yellow, rack pack, sterile
1-100ul filter tips, yellow, bag pack
1-200ul, yellow, graduated
1-200ul, yellow filter tips, graduated, sterile, rack pack
1-200ul, yellow filter tips, graduated,
Packing
96/rack
1000/box
1000/box
96/rack
96/rack
480/rack
96/rack
1000/box
page : 14
Cryogenic Tubes
PCR Tubes
KIRGEN Cryogenic Tubes
made of high q uality PP mat erial, can
withstand -196 Ԩ low t emperature, low t emperature in liquid nitrogen sample
storage; unique vial design of the sample in liquid nitrogen does not produce stress
reaction, and f ree from any inf luence in the thaw; the bottom wall t o optimize the
design of the sample easy to remove; free DNase, RNase and heat.
The thin-wall PCR tube produced by Kirgen is uniform in wall thickness to ensure
reaction system to be heated homogeneously and remarkably reduces the
evaporation;
 The V-shape dip angle design of tube fits most brands of thermal cyclers;
Features
 DNAse/RNAse free and non pyrogens.
 Internal rotation Cryo Tubes with silicone gasket to ensure tightness
 Vials external rotation without the use of unique design also ensures s ealing
silicone gasket .
 Wall area with a scale and label for easy sample identification.
 Color spin cover inserts to facilitate the coding of different samples.
Product
KG2711
descriptions
 Manufactured from tough virgin polypropylene, ultra thin wall with uniformity in
thickness.
 Flat caps and bubble caps available to fit different thermal cyclers
 Leak-proof and easy-open, comfort touch
 Low evaporation, low absorption and high thermal conductivity
Qty/pk
50/box
2.0ml Cryo Tube,
Free-Standing
bottom, Internal thread, Cap I nsert,
Natural, Silicone Ring, Sterile
15 mL and 50 mL Centrifuge Tubes
KG2311
KG2321
KG2331
KG2411
KG2421
KG2501
KG2511
KG2521
KG2531
0.2ml PCR Tubes with Attached Bubble Caps, Natural
0.2ml PCR Tubes with Attached Flat Caps, Natural
0.2ml PCR Tubes with Attached Clear Flat Caps, Natural
0.5ml PCR Tubes with Attached Bubble Caps, Natural
0.5ml PCR Tubes with Attached Flat Caps, Natural
0.2ml PCR Strips with 8 wells
0.2ml 8-Strip Bubble Caps
0.2ml 8-Strip Flat Caps
0.2ml 8-Strip Clear Flat Caps
1000/unit
1000/unit
1000/unit
1000/unit
1000/unit
125/unit
125/unit
125/unit
125/unit
Deep Well Plate
Kirgen has set a new standard for our famous
conical centrifuge tubes, not only satisfy your normal centrifugal
requirement, also offer multiple uses of sample preservation, reagent preparation etc.
 High quality PP material in accordance with FDA, ultra-transparent wall, easy to
observe
 Sterile, DNAse/RNAse free, non-pyrogenic
 Tube covered leak-proof seal design, single-hand operation switch
 Blue graduations printed to max volume, large white writing area for easy
sample identification
 Extreme temperature range of -80°C —120°C
 Maximum centrifugal force to 9500×g for 50ml and 8500×g for 15ml respectively
KG 2821
KG 2811
KG 2621
KG 2611
Description
Packing
50ml conical centrifuge tube, sterile, rack pack
50ml conical centrifuge tube, sterile, bag pack
15ml conical centrifuge tube, sterile, rack pack
15ml conical centrifuge tube, sterile, bag pack
25/rack
25/bag
50/rack
25/bag
Designs for high throughput and Ideal for sample collection, storage,
2.
Adaptable robot and different plate adaptor
combinational chemistry library applications
 Five star high-precision mold, minimize sample residual
Product No.
1.
3.
Resistant to most compound solvents
4.
Sterile is optional
5.
Round bottom wells
6.
Alpha-numeric grid for quick sample identification
7.
Sealable with well caps and sealing tape
8.
SBS footprint makes the rack robotics friendly
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 15
Product of :
GDC Environmental/USA
Nutech 3602 Vertical Autosampler
This instrument is working with either Nutech
8900 or Nutech 3550 Preconcentrator, it can
hold 16 positions for sample analysis
automation. The proposed instrument is a
vertical stand design, who saves space and is
easier to add or remove canisters. The canister
hold plate is made in stainless steal and can be
easily flipped up
Sample Preparation for VOC Analysis
Nutech 8900 Preconcentrator
This instrument is the most advanced VOC
Preconcentrator in the world, it can be used for both
EPA TO-14 and TO-15 analysis. The novel design of
hardware and software makes it more powerful in
handling all kinds of air samples. Especially, the
advanced temperature control system is able to keep
the temperature variation under +/- 2ºC, thus
guarantee more stable and accurate analysis.
Features
Application Range
Features







Three Stage Cryogenic Traps
High Sensitivity and Wide Detection Range
High Accuracy and Repeatability
Powerful Capability in Sample Handling
Advanced Temperature Control
3 Additional Sample Inlets
USB Interface and friendly software
system for auto sample loading.
Sequence operation.
System Configuration:
 16 position inlets selection.
 Automatically position back flush purge clean and leak check.
 Tower installation option with space saving.
Hardware interface and connection
 Heated sample line.
 Canister connection: Quick connectors or regular canister
 All air sample container handling: Canisters, Tedlar bags, and all
Software control:
connectors.
Nutech 2100 Canister Cleaning System
Work with Nutech 3550A, 3550DS or 8900DS pre concentration
The clean quality of a canister clean system is very
critical to the analysis quality of TO-14 or TO-15 as
well as the canister’s life time. The new designed
Nutech2100 oven heating system hosts all canisters
into a temperature controlled heating oven and the
temperature range can be from room temperature to
200ºC.The sample temperature controlled heating
strip heater is also an option.
air handling containers.
 Control and power supplies are all from 3550 or 8900 main frame
system.
 Positions feed back testing.
Dynamic Standard and Sample Dilution
System
The system is necessary to make
your own working calibration
standards from a high concentration
standard source as well as to dilute
high concentration air samples. It can
work independently with its built-in
microcontroller. Besides, a liquid
injection adaptor is also equipped for
the use of making a standard from a
liquid source.
Features
 Embedded system with touch screen LCD panel enables easy operation
like “one push then run every thing”
 Manifold assembly with 4,6,8,12 canisters
 Working Independently or through computer
 Temperature controlled heating strips with protected isolation materials
 Flexible stainless steel tube connection for canisters and manifold
 Duo Pump system with Diaphragm rough pump and molecular drug
pump
 Single Pump system with Edward high efficiency vacuum pump
 Max vacuum <50milli-Torr
Oven Manifold
holds 4 canisters up to 6L, the
entire canister is evenly heated
regardless of size
Tel : 0-2965-8971-3
Fax : 0-2965-8974
 Easy operation with built-in microcontroller
 Separate standard and sample dilution channel to avoid cross
contamination
 Liquid injection adaptor for liquid source standard
Nutech 2700 Canister Sampling Timer
Nutech 2700 Canister Sampling Timer has been
designed for canister timely field sampling. It can be set
to either time integrate or grab sampling mode.
Oven type:

Features
Features








Easy to set up any time event
Works with any time integrate flow controller
Easy to be put on to any kind of canisters
Light weight
Long battery life
Convenient Swagelok fittings in both inlet and outlet
Water proof for outdoor usage
Free of contamination condition guaranteed by
QA/QC report for each unit
page : 16
Product of :
GDC Environmental/USA
Nutech 2505 Programmable Cartridge
Auto Cleaner
The Nutech 2505 was designed to follow the protocol of
EPA methods TO-17, TO-1, TO-2 and other thermal
desorption cartridges. The Nutech 2505 cleans and
conditions thermal desorption cartridges at different
temperature range. The system handle Tenax, Charcoal,
molecular sieve cartridges and other types of adsorbent
tube cartridges. The unit is completely programmable,
user friendly software allowing the technician to walk
away while the system performs cleaning cycle.
Sample Preparation for VOC Analysis
Nutech 2505 Automatic Thermal
Desorption Unit
The Nutech 2502 system automatically analyzes VOCs
following EPA methods TO-17, TO-1 and TO-2. The
system handle Tenax, Charcoal, molecular sieve
cartridges and other types of adsorbent tube cartridges.
The Nutech 2505 works with all commercial GC and
GC/MS. Our system has a built in cryofocuser, wide
range temperature control and user-friendly software
Features :
 Performs EPA methods : TO-17, TO-1 and TO-2
 Handles all types of cartridges and adsorbent tubes.
 Compatible with all GC, GC/MS
 Built-in cryofuser
 Friendly software with gas flow direction
 Heated transfer line connects directly with column
Specifications :
 Thermal Desorption temperature range : 20 C to 300 C
 Cartridge size : ¼” W, 3.5” L
 Thermal Desorption flow : 5 to 120 ml / min.
 Software compatible with WINDOWS 2000, XP and VISTA
 Power 220 V/ 50 Hz, 1500 W
 Diamension : 22 x 25 x 30 inches (WxHxD)
Nutech 2602 Programmable Cartridge
AutoSampler
Specifications :







Flow rate setting : 5 to 120 ml/min.
Cartridge size : ¼” W, 3.5” L
Temperature range : 20 C to 400 C
Option : individual tube clean/group tube clean program.
Option : 24V DC vacuum pump for vacuum cleaning.
Display : 3 “ LCD
Power 220 V/ 50 Hz, 110 W
Nutech 2800 Large Volume Headspace
Autosampler
 Weight : 62 lbs
 Automatic cleans and conditions up to 16 cartridges at
different program ranges
 Constant flow control
 Programmble flow rates.
 Programmable temperature settings.
 Eight positions with option to 16 positions.
 Automatic temperature control.
 Accepts most types of cartridges.
 Easy to clean.
 Sensitivity : 0.2ppb or lower for most compounds.
 Thermal Desorption media : He, Air or N2
Features :
The Nutech 2602 was designed to follow the protocol of
EPA methods TO-17, TO-1, TO-2, TO-11 and other
thermal desorption cartridges. The Nutech 2602 has the
ability to program up to eight samples events and accept
a TTI signal. Can program flow rates for 1, 2, 4, 6, 8, 12,
24, 36, 48 hours. The system has an efficient pump that
assures constant flow rates. The system handle Tenax,
Charcoal, molecular sieve cartridges and other types of
adsorbent tube cartridges. The 2602 has first generation
electronic control friendly software and a large LCD
display.
The Nutech 2800 Headspace Autosampler is designed
for handling large volume headspace samples from
liquid or solid matrix. The system used with Nutech 8900
for handling large volume headspace or can directly
introduce the headspace gases to any GC or GC/MS
inlet. The Nutech 2800 headspace autosampler can be
configured as a single inlet or it can utilized multi inlets.
Applications :





Emergency response
Homeland security
Food Industry, fragrance analysis
Hazardous waste sites
EPA air toxic networks.
Features
:
 Program 8 events in 7 days period with TTI signal accept capability.
 Adjustable flow rate
Features :
 Stable constant flow






 Program time duration
 Handles Tenax SS cartridge, charcoal, molecular sieve cartridge.
 Accommodates carbonyl sampling cartridge
 Friendly software.
 Flexible cartridge connection.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Large Volume Headspace up to 500 ml volume.
Temperature controlled transfer line
Easy sample loading.
Micro computer control
Both AC and DC power supply
Carring case for field use.
page : 17
Product of :
DataApex / The Czech Repubic
Software for Chromatograph
Clarity Software for GC/HPLC
Clarity เปน
โปรแกรม Software
ประมวลผลและพิมพผล
ใชงานไดกับเครื่อง GC
และ HPLC ไดทุกยี่หอ
เปน Software ที่ใชงาน
รวมกับ WINDOWS
Operating system (Win
95, 98, ME, NT, 2000
and XP)
Acquisition of Chromatographic
Data
Clarity offers the possibility to collect data from any chromatographic detector with
a voltage output. In co-operation with an autosampler the station enables one not
only to collect and process chromatographic data but to provide a comprehensive
printed report of the analytical results.
 Simply to use – Set acquisition rate, end time and go.
 Up to 4 channels options per A/D converter
 Manipulate and save analysis conditions post run
 Single run or sequence run capability.
 Live on screen display of instrument output.
 Manual or automatic integration.
 Multi-Level, Multi-component calibration.
 Fully detailed action log.
 Fully editable report formats.
 Comprehensive online help.
Key Features
สําหรับทานที่มีเครื่อง GC และ HPLC ใชงานรวมกับ Integrator ที่ใช
งานมานานแลว ตองการ Upgrade เครื่อง Integrator ใหเปนเครื่อง
Computer ที่สามารถเก็บขอมูลการวิเคราะหได บริษัทฯ ขอแนะนํา
Clarity Chromatography Software เปนโปรแกรมที่ใชรวมกับ
Computer ที่สามารถเก็บขอมูลผลการวิเคราะห แสดงผลการวิเคราะห
และมีคุณสมบัติ ดังนี้
 เปนโปรแกรมที่ทํางานภายใต MS WINDOWS 95, 98, ME,
NT, 2000 และ XP
 มีลักษณะเปน Graphical User Interface สะดวกและงายตอ
การใชงาน
 สามารถรับสัญญาณจากเครื่อง GC หรือ HPLC ได 1 ถึง 12
ชองสัญญาณ (Optional) ในเวลาเดียวกัน หรือแยกจากกัน
โดยอิสสระ
 สามารถทํา manual หรือ automatic integration ได
 รวบรวมขอมูลโดยการ plot, replot, reintegration และ
แสดงผลทางจอภาพเครื่องคอมพิวเตอร
 ขณะบันทึกโครมาโตแกรม สามารถเปลี่ยน Time Window,
Attenuation บนจอเพื่อใหได peak ทีม่ ีรูปรางดีขึ้น
 รายงานขอมูลคํานวณอัตโนมัติ โดยวิธีการคํานวณมาตรฐาน
เชน Area %, Norm %, ESTD และ ISTD
 โปรแกรมแสงผลทํางานไดหลายหนาที่พรอมกัน (Multi
Tasking) สามารถใชงานในโปรแกรมอื่นไดในขณะที่รอผลการ
วิเคราะห
 แสดงผล Calibration Curve ของสารมาตรฐานได
 Etc.
Clarity for Single Instrument, Single Detector
P/N C50 Clarity Extensible, Single Instrument SW, CFR21/GLP ready
P/N I71 INT7 Internal PCI, 1 channel
Clarity for Single Instrument, Two Detectors
P/N C55 Clarity Add-on, Single Instrument Add-on
Clarity Control GC Agilent 5890
บริษัทฯ ขอเสนอ Clarity ที่สามารถควบคุม
การทํางานเครื่อง GC Agilent model
5890A และ 5890 series II และรับ
สัญญาณจาก Detector มา ประมวลผล
พิมพผลการวิเคราะห ได
Clarity for Agilent 5890, Two Detectors
P/N A26 AS Control SW module for AS control
P/N SKXX
RS 232-Communication cable
Clarity Control GC Agilent 6890
บริษัทฯ ขอเสนอ Clarity ที่สามารถควบคุม
การทํางานเครื่อง GC Agilent model
6890, 6890N, 6820, 6850 และรับ
สัญญาณจาก Detector มา ประมวลผล
พิมพผลการวิเคราะห ได
Clarity for Agilent 6890, Two Detectors
P/N SKXX
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 18
Product of :
DataApex / The Czech Republic
Software for Chromatograph
One Chromatograph with two detectors
Clarity Control GC Shimadzu 2014C
The control module intended for Shimadzu GC2014C chromatograph. It allows a limited control
of the GC-2014 and GC-2010 - AFC (automatic
flow control) and APC (automatic pressure
control) parameters must be still set from the GC
keyboard.
Clarity for GC Shimadzu 2014C, Two Detectors
P/N SKXX
Clarity for one chromatograph with two Detector
Two Chromatographs each with single detector
Clarity Control SYKAM S4300 Amino Acid
Reaction Module
กรุณาสอบถามรายละเอียด
ของสินคา กอนสั่งซื้อสินคา
Clarity for CHNS-O Elemental analyzer
Clarity for Two Chromatographs each with Single Detector
Two Chromatographs one with multiple detectors
EA Extension is a software module for Elemental
Analysis. Determining the Carbon, Hydrogen,
Nitrogen, Oxygen, and Sulphur (C HNS-O)
content of unknowns is one of the most basic
and essential needs of any chemist.
EA Extension provides a simplified version of the
Clarity user int erface that speeds up the
workflow with elemental analyzers equipped by
autosamplers.
EA Extension is an optional addition to Clarity
software, it cannot be u sed as a standalone
program. Its user interface is opt imized for
maximum efficiency in r epetitive tasks. Using
features that are specific to EA Analysis, such as
Standard Table, automatic weight input from
analytical balance and other improvements,
EA Extension provides an interactive and
automated tool for determining the Carbon,
Hydrogen, Nitrogen, Oxygen, and Sulfur (CHNSO) content of unknowns.
Clarity for Two Chromatographs one with multiple Detectors
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Clarity Software สามารถควบคุมการทํางาน
เครื่อง GC และ HPLC ไดอีกหลายยีห
่ อ โปรดสอบถาม
วันจันทร – วันศุกร เวลา 8.30 น. -17.00 น.
page : 19
COSMOSIL Sugar -D
Product of :
Cosmosil / Japan
HPLC Column
COSMOSIL 5C18-MS-II
COSMOSIL 5C18-MS-II is a monomeric type of
C18 phase. A new endcapping treatment with
polar groups for "shield effect" has extended the
pH range and significantly improved peak shape
for basic compounds. This phase is recommended
for most of applications but particularly effective
for low molecular weight organic compounds.
COSMOSIL 5C18-AR-II
COSMOSIL 5C18-AR-II is a polymeric
type of C18 phase. It shows exceptional
stability and long lifetime at low pH. This
phase is recommended for the
separations requiring acidic mobile
phase conditions. It also shows superior
molecular shape selectivity to monomeric
type C18 columns
COSMOSIL HILIC
COSMOSIL 5C18-PAQ
COSMOSIL 5C18-PAQ is designed to offer superior
retention of polar compounds and excellent
reproducibility in highly aqueous mobile phases, even
in 100% aqueous.
COSMOSIL πNAP
COSMOSIL πNAP is a Reversed Phase
HPLC Column with naphtylethyl group
bonded silica packing material. The
naphthylethyl group is composed of two
fused aromatic rings and forms strong π-π
interactions with unsaturated compounds.
This column offers improved selectivity for
structural isomers that exhibit differences in
saturation.
COSMOSIL Cholester
COSMOSIL Cholester is a new silica
based RP column which employs a
cholestery bonded phase. Cholester
provides enhanced selectivity over
traditional C18 materials and greater
performance in separating isomers or
other closely related compounds.
Cholester is ideal for method development
and serves as an excellent alternative to
traditional C18 columns
Fax : 0-2965-8974
The main retention mechanism is the partitioning of the polar analytes
between the polar stationary and the non-polar mobile phase. As it is
also called "aqueous normal phase", the elution order is similar to that of
normal phase and the sample elution is in the order of increasing
hydrophilicity. Without using ion-pair reagent COSMOSIL HILIC retains
highly polar analytes that would not be retained in reversed phase
chromatography. It also shows a weak anion-exchange mechanism with
the positively charged stationary phase, thus acidic compound is
bonded silica based column specifically designed
for fullerene separation. The unparalleled
separation capabilities have enabled COSMOSIL
Buckyprep to become the world benchmark of
HPLC column for fullerene separation.
COSMOSIL PYE (pyrenylethyl group bonded) and
COSMOSIL NPE (nitrophenylethyl group bonded) column
show unique retention characteristics based on multiple
separation modes such as hydrophobic, charge transfer
and π-π interactions. These columns are recommended
for the separation of structural isomers.
Tel : 0-2965-8971-3
COSMOSIL HILIC is a new column for
hydrophilic interaction
chromatography with Triazole bonded
silica packing material. The
hydrophilic interaction
chromatography is a variation of
normal phase chromatography where
a polar stationary phase is used with
a mobile phase which contains a high
concentration of organic solvent and a
low concentration of aqueous eluent.
COSMOSIL Buckyprep
COSMOSIL Buckyprep is a pyrenylpropyl group
COSMOSIL PYE, COSMOSIL NPE
Conventionally Aminopropyl bounded
stationary phases are used for liquid
chromatographic analysis of mono- and
oligosaccharides. General shortcomings
of the conventional Aminopropyl
bounded phases are tailing and
adsorption of certain saccharides and
general low durability (short active life) of
these columns. These problems are
addressed and solved by the novel
COSMOSIL® Sugar-D, resulting in better
(sharper) separation and much improved
durability.
COSMOSIL Buckyprep retains fullerenes very strongly with a mobile
phase of 100% toluene and exceeds the injection volume of a standard
C18 column by a factor of 35. Therefore, preparative-scale separation
can be obtained with a 250 mm x 4.6 mm I.D. analytical column.
COSMOSIL Buckyprep
COSMOSIL PBB is a pentabromobenzyl
group bonded silica based column useful
for preparative-scale separation of
fullerenes. It can be used with carbon
disulfide or 1,2,4-trichlorobenzene, which
has greater solubility for fullerenes than
toluene. The loading capacity of
COSMOSIL PBB for C60 and C70 can
be three times greater than COSMOSIL
Buckyprep.
page : 20
Product of :
Abel Industries / Canada
GC Capillary
Column
Abel IndustriesTM Canada Ltd. Abel Industries (Canada) Ltd was originated in 1997 with its headquarter in Vancouver,
British Columbia, Canada. It is a manufacturing and servicing company focusing on
chromatographic separations and lab supplies. With more than 15 years of labs and
industries experience, and complete quality control over its’ manufacturing facilities in both
Canada and overseas; Abel is able to produce top line product in the industry.
Abel offers Abel Bonded (AB) series gas chromatographic
capillary columns:
1.Complete stationary phase selections, Polysiloxane, Polyethylene glycol and PLOTs;
2.Consistent high performance such as low column bleed, more inert and high efficiency;
3.Great peak shapes;
4.Individually tested to meet the tightest quality control specifications;
5.Competitive price;
AbelBonded GC column performances
Column performances are characterized as stationary phase, column selectivity and
retention time. AB GC columns are reengineered and made by the same stationary phases
as most column makers with stringent process control to replicate column selectivity and
retention time in order to ensure seamless column switching. Table I to III illustrate the
performance comparisons of the most popular stationary phases: AB-5MS and AB-Inowax
vs the brand name columns
Abel offers the following product lines:
AbelBondedTM(AB) GC Columns:





















AB-1
AB-1MS
AB-5
AB-5MS
AB-PONA
AB Builtin-Guard
AB-Inowax
AB-FFAP
AB-Carbowax-20M
AB-624
AB-225
AB-35
AB-1301
AB-1701
AB-PLOT AL2O3 “KCL”
AB-PLOT AL2O3 “S”
AB-PLOT AL2O3 “M”
AB-PLOT Molesieve
AB-PLOT U
AB-PLOT Q
Customized columns
Very low column bleed
Low column bleed is an industrial trend to push applications to
new limits, such as temperature limit, and detection limit. Low
column bleed also implies long life time of column. Low column
bleed means crosslinked and bonded stationary phases. Shipping :
Our standard shipping method is EMS,
FedEx or UPS. Buyer is fully
responsible for the shipping and
handling fees, as well as all taxes,
custom duty or other fees.
Delivery Time in Thailand :
We committed to deliver the Abel
Column to your place within 15 days
even your order is only 1 pc. Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 21
Product of :
Trigon Technologies/USA
Excelasorb Multi-Propose traps
Oxygen/Moisture traps
Trigon's layered bed, multi-purpose trap is designed to
Trigon oxygen/moisture traps are ideal for use in gas
chromatography and GC/MS. These traps utilize a one-piece spun
aluminum body and Swagelok™ end fittings. Each fitting incorporates a 40
micron stainless steel frit for particulate control. A regeneration service is
offered for the high capacity model.
remove oxygen, moisture, hydrocarbons and carbon dioxide from gas
streams. This 750cc unit will take the place of three separate traps,
simplifying installation and reducing the number of potential leak sites that
contribute to the aspiration of contaminants into the system. End fittings
are stainless steel Swagelok™ fitted with 40 micron stainless steel frits. A
regeneration service is offered.
Glass Body Indicating Moisture traps
Hydrocarbon traps
Hydrocarbon/Moisture traps
Trigon glass moisture traps are impervious to the infusion and
Trigon hydrocarbon traps utilize a very high surface area
activated carbon. These refillable traps are available in several
configurations. The standard model contains 200cc of filtering medium. For
highly critical applications such as carrier gas lines in gas chromatography
and GC/MS we offer 100cc and 750cc units that feature one piece spun
aluminum bodies and are helium purged prior to shipment. Each
Swagelok™ end fitting includes a 40 micron stainless steel frit.
High Capacity Moisture traps
Indicating Oxygen traps
These glass-bodied traps utilize a non-hazardous material that reduces
oxygen levels to less than 1 ppb. This indicating adsorbent changes color
from a light green to deep brown as it adsorbs oxygen. Either of these
traps is ideal as an indicator installed downstream of the Trigon
Oxygen/Moisture trap. This allows high capacity removal of oxygen with
the benefit of an indicator to alert the user of saturation of the primary trap.
End fittings are nickel plated Swagelok™ with 40 micron stainless steel
frits. A regeneration service is also offered.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
out-gassing of contaminants sometimes associated with plastic bodied
traps. These are the best moisture traps available for use on carrier gas
lines in gas chromatography and GC/MS, as well as other applications
where high integrity moisture removal is desired. The glass moisture trap is
filled with molecular sieve 13X and incorporates a band of indicating
molecular sieve 4A. The refill kit contains sufficient material to refill three
70cc units, two 100cc units or one 250cc model. Each nickel plated
Swagelok™ end fitting includes a 40 micron stainless steel frit.
This high capacity, refillable model contains 750cc of molecular sieve
13X. The trap body is one piece spun aluminum. The refill includes
sufficient material to recharge this trap twice. Each Swagelok™ end fitting
includes a 40 micron stainless steel frit.
page : 22
Vial for GC & HPLC Autosampler
Product of :
CeiExpert / Thailand
OEM products from : Aijiren Technology Co., Ltd.
Economical Syringe Filters
AutoSampler Vials
For Most GC & HPLC Instruments
OEM Products from : Aijiren Technology Co., Ltd.
C.E. Instruments (Thailand) Co., Ltd. offers an exclusive
line of CeiExpert disposable syringe filter devices designed to provide
efficient filtration of aqueous and organic solutions. They are made with a
wide variety of membrane filters with a polypropylene housing using the
most advanced methods and design features available today. These
syringe filters are ideal for numerous applications in pharmaceutical,
environmental, biotechnology, food/beverage, and agricultural testing
laboratories.
High Quality, Guaranteed Lowest price in Thailand.
Features
 Wider opening prevents syringe problems.
 Screw thread caps, Crimp caps septa, and vials are designed especially for use
with Agilent's, Water Alliance’s and other rotating or robotic arm samplers.
 Clear vial, 33 Expansion borosilicate glass (Type 1, Class A)
 Amber vial, 51 Expansion borosilicate glass (Type 1, Class B)
 Vials provide graduated write-on marking spot area, measures 0.5, 1.0 and 1.5ml
 Caps are made of high quality material to exact manufacturing tolerances.
 Septa made of the highest quality materials to ensure proper function.
 Red PTFE/White Silicone Septa.
 Pre-slit Red PTFE / White Silicone Septa.
Products
CeiExpert Syringe Filters (With luer-lock inlet)




Variety of filter types, porosities, and diameters.
Color coded for easy identification.
Reusable storage container for 100-pk.
Quantity break pricing, for greater savings.
Features















Screw Neck, ND8 vials, 8-425 Screw Thread Vial
Screw Neck ND9, 9mm Short Screw Vial
11mm ND11,Snap Top Vial
11 mm ND11, Crimp Top Vial
Vial Inserts
4ml Screw neck, 13-425 Screw Thread Vial
Screw Headspace Vial, ND18
Crimp Headspace Vial, ND20
ND22 Storage Vial
1ml shell vial
0.3ml PP Snap Ring Micro-Vial, clear 11.6*32mm
PTFE/Silicone Septa & Caps
13mm, 20mm, 25 mm, 30mm diameter syringe filters
Polypropylene housing
Pore size : 0.22um, 0.45um and 0.8um
Membrane :








Nylon 66
Polypropylene (PP)
Polyether sulfone (PES)
Polyvinylidene fluoride (PVDF)
Polytetrafluoroethylene (PTFE)
Cellulose acetate (CA)
Mixed Cellulose (MCE)
วางจําหนาย เดือนเมษายน 2555 เปนตนไป
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 23
Product of : CeiExpert /Thailand
Vial 2 ml, 9mm Screw neck, wide opening
12x32 mm with Caps, Septa and Inserts.
OEM Products from : Aijiren Technology Co., Ltd.
AutoSampler Vials
For Most GC & HPLC Instruments
2mL, Small opening 8-425 screw thread Vial ,
12 x 32 mm with Caps, Septa and Inserts.
Features
 Wider opening prevents syringe problems.
 9mm screw thread caps, septa, and vials are designed especially for use
with Agilent's, Water Alliance’s and other rotating or robotic arm
samplers.
 Vials provide graduated write-on marking spot area, measures 0.5, 1.0
and 1.5ml
 Caps made of high quality polypropylene to exact manufacturing
tolerances.
 Our septa use only the highest quality materials to ensure proper
function and can be pre-slit to ease needle penetration.
 Septa Available : Red PTFE/White Silicone, White PTFE/Red Silicone,
Blue PTFE/White Silicone
 Pre-slit Septa available : Red PTFE/White Silicone, White PTFE/Red
Silicone, Blue PTFE/White Silicone
 Designed for multiple injections and/or longer sample cycles - for both
GC and LC applications
 High quality silicone compounds are used to ensure proper re-sealing
and reduced chances of coring
Features
 8-425 screw thread caps and vials are often used in conjunction with CTC
Autosampler, Shimadzu, ThermoScientific, Varian and other autosamplers.
 Vials provide graduated write-on marking spot area, measures 0.5, 1.0 and
1.5ml
tolerances.
 Our septa use only the highest quality materials to ensure proper function
and can be pre-slit to ease needle penetration.
Blue PTFE/White Silicone
 Pre-slit Septa available : Red PTFE/White Silicone, White PTFE/Red
Silicone, Blue PTFE/White Silicone
 Designed for multiple injections and/or longer sample cycles - for both GC
and LC applications
 High quality silicone compounds are used to ensure proper re-sealing and
reduced chances of coring
Screw neck ND9 Vials - 9mm Screw neck ND9 Vials,12 x 32 mm
Description
2ml screw neck ND9 Vial, Clear
2ml screw neck ND9 Vial, Amber
2ml screw neck ND9 Vial, Clear with Marking Spot
2ml screw neck ND9 Vial, Amber with Marking Spot
PP Screw caps – 9 mm, Screw caps
Screw neck ND8 Vials - 12 x 32mm Screw neck ND8 Vials, 8 mm
Description
2ml screw neck ND8 Vial, Clear
2ml screw neck ND8 Vial, Amber
2ml screw neck ND8 Vial, with Marking Spot, Clear
2ml screw neck ND8 Vial, with Marking Spot , Amber
Pk/100
120801
120802
120803
120804
3
4
3
4
PP Screw caps – thread 8-425 for screw neck ND8 Vials, 8mm
Description
8mm PP screw thread cap, Black center hole 5.5mm
with Red PTFE/White Silicone septa 8 x 1.5mm
8mm PP screw thread cap, White, centre hole, 5.5mm
8mm PP screw thread cap, Black, centre hole, 5.5mm
Septa Red PTFE/White Silicone, 8 x 1.5 mm
Pk/100
120807
4
120808
120809
120810
1
3
Pk/100
120901
120902
120903
120904
for screw neck ND9 Vials
Description
9mm PP screw thread cap, Blue, center hole 6mm
with Red PTFE/White Silicone septa 9 x 1 mm
9mm PP screw thread cap, Blue, centre hole, 6mm
Septa Red PTFE/White Silicone, 9 x 1mm
Pk/100
120907
120909
120910
Glass Inserts - for 9 mm Screw neck ND9 Vials
Description
200ul 6x29 mm glass insert w/PP spring bottom
200ul 6x31 mm, glass insert conical bottom
300ul 6x31 mm glass insert flat bottom
Pk/100
120913
120914
120915
Glass Inserts - for 12 x 32mm Screw neck ND8 Vials, 8 mm
Description
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Pk/100
120813
120814
120815
1,2
8
3
page : 24
1
Vial for Headspace Autosampler, Screw neck
and Crimp Top
Vial 2 ml, Crimp Top, wide opening 12x32 mm
with Caps, Septa and Inserts.
Precision Screw thread ND18 Vials
USP Type I Glass Vials
Precision Screw thread Headspace Vials rounded bottom.
Suitable for CTC Autosampler
Precision Screw thread ND18 Vials - 22.5 x 46 mm and 22.5 x
75.5 mm ND18 Vials
Features
Description
10ml Screw thread ND18 Vial, Clear Round Bottom
20ml Screw thread ND18 Vial, Clear Round Bottom
 11mm crimp neck vials have a larger opening to ensure proper needle
penetration.
 Vials provide graduated write-on marking spot area, measures 0.5, 1.0
and 1.5ml
tolerances.
 Our septa use only the highest quality materials to ensure proper function
and can be pre-slit to ease needle penetration.
Blue PTFE/White Silicone, Clear FEP/Orange Silicone
 Designed for multiple injections and/or longer sample cycles - for both GC
and LC applications
 High quality silicone compounds are used to ensure proper re-sealing and
reduced chances of coring
Magnetic Screw Cap and Septa for Precision Thread
Vials ND18
Description
18mm Magnetic screw cap, silver, 8mm center hole
with blue PTFE/white Silicone septa
Septa Blue PTFE/white Silicone, 17.5 x 1.5mm
18mm Magnetic screw cap, silver, 8mm centre hole
Pk/100
121803
121804
121805
Crimp Neck ND20 Vials
Borosilicate Type I Glass Vials
Crimp Neck Headspace Vials are available with either a flat or
rounded bottom.
Crimp Neck ND11 Vials - 12 x 32mm Crimp Neck
Crimp Neck ND20 Vials - 22.5 x 46 mm and 22.5 x 75.5 mm ND20
Vials, 11mm
Vials
Description
2ml Crimp Neck ND11 Vial, Clear
2ml Crimp Neck ND11 Vial, Amber
2ml Crimp Neck ND11 Vial, Clear with Marking Spot
2ml Crimp Neck ND11 Vial, Amber with Marking Spot
Pk/100
121111
121112
121113
121114
Aluminium Crimp Seals - for Crimp Neck
3
4
3
4
ND11 Vials,
11mm
Description
11mm Alu. Crimp Cap, clear lacquered, centre hole
5.5mm with Red PTFE/White Silicone 11 x 1 mm
11mm Alu. Crimp Cap, clear lacquered, centre hole
5.5mm with Clear FEP/Orange Silicone 11 x 1 mm
121117
5
121118
3
11mm
Description
Fax : 0-2965-8974
Pk/100
120913
120914
120915
Description
10ml crimp neck ND20 vial, clear, flat bottom
10ml crimp neck ND20 vial, Amber, flat bottom
20ml crimp neck ND20 vial, clear, flat bottom
20ml crimp neck ND20 vial, Amber, flat bottom
10ml crimp neck ND20 vial, clear, Round bottom
20ml crimp neck ND20 vial, clear, Round bottom
Aluminium Crimp Seals – 20 mm, for Crimp Neck
Pk/100
Glass Inserts - for 12 x 32mm Crimp Neck ND11 Vials,
Tel : 0-2965-8971-3
Pk/100
121801
121802
1,4
6
3
Description
20mm Aluminium Crimp Cap, 10mm centre hole
with nature PTFE/nature Silicone septa
20mm Magnetic Crimp Cap, 10mm center hole
with nature PTFE/nature Silicone septa
20mm Aluminium Crimp Cap, centre hole 10mm
Septa nature PTFE/nature Silicone, 20 x 3mm
Aluminium Crimp Seals – 20 mm, for Crimp Neck
Description
20mm Hand Crimper
Pk/100
122001
122002
122003
122004
122005
122007
ND20 Vials.
Pk/100
122009
122010
122011
120012
ND20 Vials.
122013
page : 25
1ml shell vial
VOA Storage Vial
Shell Vials
Economical Shell Vial 1ml

borosilicate, 33 expansion glass or amber, Type I, borosilicate, 51
Storage Vials
expansion glass.
20mL, 30mL, 40mL and 60mL

Caps are made from Polyethylene.

These vials are custom designed to fit the Waters autosamplers, and o
ther leading instruments using 4-mL and 1-mL vials.
Economical Storage Vials
Screw thread ND24 Vials

Both sizes are available in clear glass.

Chemically resistant borosilicate vials withstand temperatures up to 60
0 – 700 °C and are ideal for pH sensitive samples and sodium or
heavy metal analysis.
Borosilicate Type I Glass Vials








These vials are ideal for use in water sampling according to EPA method.
Clear vial, 33 Expansion borosilicate glass (Type 1, Class A)
Amber vial, 50 Expansion borosilicate glass (Type 1, Class B)
Caps are made of high quality polypropylene to exact manufacturing
tolerances.
Septa made of the highest quality materials to ensure proper function.
Nature PTFE / Nature Silicone Septa.
Blue PTFE / White Silicone Septa.
All vials are packaged in convenient trays which facilitates handling.

1-mL Vials for 96-position autosamplers measure 8 x 40 mm. Include
polyethylene Sepcaps for easy needle penetration.

Caps feature a sealing ring for volatile sample containment.
Shell Vial 1ml –8.2 x 40mm
Description
1ml shell vials, clear, 8mm PE-Plug, soft, without
insertion 8.2*40mm
Pk/100
120101
700
13mm Screw thread vial, 13-425
20mL Screw thread ND24 Vials – 27 x 58 mm ND24 Vials
Description
20ml screw neck ND24 vial, clear
20ml screw neck ND24 vial, amber
Specification Glass vials we offered are made from clear, Type I
Pk/100
122401
122402
700
700
Pk/100
122403
950
30mL Screw thread ND24 Vials – ND24 Vials
Description
 13-425 screw thread caps, septa, and vials are designed for specific
40mL Screw thread ND24 Vials – 27x 95 mm ND24 Vials
Description
Pk/100
122404
122405
use with the Waters WISP 48-Position Autosampler
950
950
Pk/100
122406
122407
Tel : 0-2965-8971-3
Fax : 0-2965-8974
 Caps are made of high quality polypropylene to exact manufacturing
 Cap colors are available in black only
1,900
1,900
Screw Cap and Septa Thread ND24 Vials
Description
24mm PP Screw Cap, white, centre hole with nature
PTFE/nature Silicone septa
24mm PP Screw Cap, white, centre hole 15mm
24mm PP Screw Cap, white, closed top
Septa nature PTFE/nature Silicone, 22 x 3mm
 Amber, Type 1 Class B borosilicate glass.
tolerances and lined in a controlled manufacturing environment
60mL Screw thread ND24 Vials – 27 x 140 mm ND24 Vials
Description
 Vials are manufactured of Clear, Type 1 Borosilicate Expansion33
Pk/100
122408
1,300
122409
122410
122411
300
300
900
 Our septa use only the highest quality materials to ensure proper
function and can be pre-slit to ease needle penetration
4mL Screw thread ND13 Vials
Description
Pk/100
120401
120402
1,900
1,900
Screw Cap and Septa Thread ND13 Vials
Description
13mm PP Screw Cap, black, centre hole with
PTFE/white Silicone septa
Septa Red PTFE/white Silicone, 13 x 1.5mm
Pk/100
120403
1,300
120406
900
page : 26
Product of :
/ China
Xiboshi Syringe Filters for Ion Chromatograph
High Class Syringe Filters and
membrane Filters
Xiboshi Syringe Filters for HPLC
Features







Features







13 and 25 mm diameter syringe filters
Pigment-free polypropylene housing
Prefiltration stack of GF glass microfiber media for 25mm
Prefiltration stack of Polypropylene fiber media for 13mm
Sterile options
Construction facilitates exceptional loading capacity with fast flow rates.
Pore size : 0.2um and 0.45um
Membrane :


Nylon 66
IC Certificate
Membrane :






13 and 25 mm diameter syringe filters
Pigment-free polypropylene housing
Prefiltration stack of GF glass microfiber media for 25mm
Prefiltration stack of Polypropylene fiber media for 13mm
Sterile options
Construction facilitates exceptional loading capacity with fast flow rates.
Pore size : 0.2um
Our company carries on the ion chromatograph analysis to the leaving the
plant each raid of IC level disposable syringe filter sample, 1ml pure water
Nylon 66
Polyvinylidene fluoride (PVDF)
Polytetrafluoroethylene (PTFE)
Cellulose acetate (CA)
Mixed Cellulose (MCE)
after filtering will carry on the analysis, demonstrated that the level of the ion
dissolving achieve using level of the ion chromatograph analysis.
Ion Remainder
Syringe Filters 13mm with PP Prefilters
Descriptions
Nylon Syringe Filter 13 mm 0.2 um
MCE Syringe Filter 13 mm 0.2 um
PVDF Syringe Filter 13 mm 0.2 um
CA Syringe Filter 13 mm 0.2 um
PES Syringe Filter 13 mm 0.2 um
PTFE Syringe Filter 13 mm 0.2 um
Non Sterilized
100/pk
Sterilized
100/pk
TNL1320
TNL1345
TMC1320
TMC1345
TPV1320
TPV1345
TCA1320
TCA1345
TPE1320
TPE1345
TPT1320
TPT1345
TNLS1320
TNLS1345
TMCS1320
TMCS1345
TPVS1320
TPVS1345
TCAS1320
TCAS1345
TPES1320
TPES1345
TPTS1320
TPTS1345
ppb
Cl-
< 30
SO4-
< 30
NO3-
< 40
Descriptions
Qty 100/pk
TNL1320
TPE1320
Descriptions
Qty 100/pk
TNL2520
TPT2520
Xiboshi Membrane Filters
Nylon Membrane Filters
Nylon membrane has high mechanical
strength, chemical stability, can be tolerated
Syringe Filters 25mm with GF Prefilters
by most organic solvents and the majority of
water solution filter characteristics. It more
Descriptions
Non-Sterilized
100/pk
TNL2520
TNL2545
TMC2520
TMC2545
TPV2520
TPV2545
TCA2520
TCA2545
TPT2520
TPT2545
TPE2520
TPE2545
Sterilized
100/pk
TNLS2520
TNLS2545
TMCS2520
TMCS2545
TPVS2520
TPVS2545
TCAS2520
TCAS2545
TPES2520
TPES2545
TPTS2520
TPTS2545
often applied to the common organic solvent
HPLC mobile phase filtering.
-
Material
Nylon
Pore size
0.1um 0.2um 0.45um 0.8um
Size
47um 50um
Thickness
80um
Operating temperature
Sterilization methods
75Ԩ
Cat. NO.
MNL5020
MNL5045
Ethylene oxide sterilized、 Autoclave sterilization
(121 Ԩ, 1bar), γ ray sterilization
Membrane Type
Nylon Membrane Filter 50mm 0.2um
Nylon Membrane Filter 50mm 0.45um
Qty/pk
100
100
*** Xiboshi products OEM for Dionex and ThermoFisher ***
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 27
MCE Membrane Filters
PES Membrane Filters
MCE membrane has high mechanical
PES membrane has a strict pore size
distribution, high flow rate, throughput, low
protein adsorption, high strength
characteristics. It has a hydrophilic that it
commonly used in filter of biological
samples.
strength, chemical stability, can be tolerated
by most organic solvents and the majority of
water solution filter characteristics. It more
often applied to the common organic solvent
HPLC mobile phase filtering.
Material
Cellulose Acetate and Cellulose Nitric
Material
PES
Pore size
0.1um 0.2um 0.45um 0.8um
Pore size
0.1um 0.2um 0.45um 0.8um
Size
47um 50um
Size
47um 50um
Thickness
60um
Thickness
80um
60 Ԩ
65 Ԩ
Cat. NO.
MMC5020
MMC5045
Membrane Type
MCE Membrane Filter 50mm 0.2um
MCE Membrane Filter 50mm 0.45um
Qty/pk
100
100
PTFE Membrane Filters
Cat. NO.
MPE5020
MPE5045
Membrane Type
PES Membrane Filter,50mm 0.2um
PES Membrane Filter,50mm 0.45um
Qty/pk
100
100
Xiboshi Solid Phase Extraction with syringe
adapter
PTFE membrane has excellent chemical
stability .It can be used in extreme liquid
and temperature conditions which other
membrane can not filter . It has a
hydrophobic can be used for air filtration or
degassing filter.
Material
PTFE
Pore size
0.1um 0.2um 0.45um 0.8um
Size
47um 50um
Thickness
60um
Cat. NO.
MPT5020
MPT5045
Solid Phase Extraction Cartridge with syringe
adapter
260 Ԩ
Membrane Type
PTFE Membrane Filter,50mm 0.2um
PTFE Membrane Filter,50mm 0.45um
Qty/pk
100
100
PVDF Membrane Filters
PVDF membrane has good chemical
compatibility, can be competent for the vast
majority of organic solvent and strong
corrosion chemical filter. It has a
hydrophobic can filter aqueous solution after
wetting with ethanol.
Material
PVDF
Pore size
0.1um 0.2um 0.45um 0.8um
Size
47um 50um
Thickness
80um
80 Ԩ
Cat. NO.
MPV5020
MPV5045
Membrane Type
PVDF Membrane Filter,50mm 0.2um
PVDF Membrane Filter,50mm 0.45um
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Qty/pk
100
100
SPE (solid phase extraction column), since the self-developed sieve plate and
filling technology has matured, making our products in high-pressure liquid
Chromatography, ion chromatography and other aspects of sample preparation
has a very good performance. Xibosh solid-phase extraction column (morphine
column) Unique sample separation, enrichment, purification, access to Chinese
Pharmaceutical and Biological Products Laboratory of the drug approval narcotics
center. And promoting the use of In compound liquorice and other products in the
oral morphine, codeine phosphate quantitative detection.
SPE cartridge for Ion Chromatograph
Cat.No.
Descriptions
Qty/pkg
SIC18300
SIRP05
SIRP10
SIH05
SIH10
SIAg05
SIAg10
SINa05
SINa10
SIAgH10
SIAgNa10
C18 300mg
RP 0.5cc
RP 1.0cc
H 0.5cc
H 1.0cc
Ag 0.5cc
Ag 1.0cc
Na 0.5cc
Na 1.0cc
Ag/H 1.0cc
Ag/Na 1.0cc
SPE Cartridge for GC and HPLC
Cat.No.
Descriptions
100
100
100
100
100
100
100
100
100
100
100
Qty/pkg
SHC181001
C18 100mg/1ml
100
SHC182503
C18 250mg/3ml
100
SHC185003
C18 500mg/3ml
100
SHC185006
C18 500mg/6ml
50
page : 28
Product of : CeiExpert
CeiExpert / Thailand
24 Ports SPE Vacuum Manifold
12 ports SPE Vacuum Manifold
Vacuum Manifold for Solid Phase Extraction (SPE)





Vacuum Manifold for Solid Phase Extraction (SPE) 





Multiple sample processing saves time and money.
Female Luer inlets fit all male Luer tipped SPE tubes and cartridges.
Compatible with standard Luer-tipped SPE and filtration columns.
Glass chamber allows easy visual monitoring.
Adjustable racks accommodate a variety of test tubes, vials and flasks.
12 positions for standard tubes.

P/N 82401 Vacuum manifold 12 ports Completed
with :












P/N 81201 Vacuum manifold 12 ports Completed
with :













Glass chamber
12 position cover with luer fittings
Vacuum Gauge
12 Retaining Clips
Gasket
4 supports
12 Individual Flow Control Stopcocks
12 Luer Plugs
3 Posts
Valve Assemble
6 Shelves
Waste container
12 Guide needles
Multiple sample processing saves time and money.
Female Luer inlets fit all male Luer tipped SPE tubes and cartridges.
Compatible with standard Luer-tipped SPE and filtration columns.
Glass chamber allows easy visual monitoring.
Adjustable racks accommodate a variety of test tubes, vials and
flasks.
24 positions for standard tubes.
Glass chamber
24 position cover with luer fittings
Vacuum Gauge
24 Retaining Clips
Gasket
4 supports
24 Individual Flow Control Stopcocks
24 Luer Plugs
3 Posts
Valve Assemble
4 Shelves
24 Guide needles
Oil-Less Diaphragm Vacuum Pump for SPE Vacuum Manifold
Specifications : MODEL AS-1001 Vacuum Pump
Type
Power Requirement
Maximum Current
Power Consumption
Motor
Vacuum
Air Flow
Diamensions (L*W*H)
Product Weight
Tel : 0-2965-8971-3
Fax : 0-2965-8974
Oil-less Vacuum Diaphragm Pump
220 VAC, 50 Hz
0.4 A
70 W
1/8 HP AC
0 - 550 mmHg
38 l/m
L 33.5 * W 16 * H 21.5 cm
4.4 kg
page : 29
Product of :
Spex CertiPrep / USA
Certify Refernce Standard
Certify Reference Material
Product of :
Gas Control Equipment/Germany
High Purity
Gas Control Equipment
GCE High Purity gas Control Equipment
Quality Management
GCE DruVa clean-gas systems prove its quality by performance and reliability
The production process of the regulators is certified according to ISO9001 and
ISO13486 at regular intervals This certification is considered by GCE DruVa as
only one step in the long path towards not only gaining and keeping the
confidence of our customers in our products but also to strengthen it
Unannounced re-audits by internal and external supervisors assure a continuous
quality level
Welcome to the SPEX CertiPrep Certified Reference
Materials
As in previous years, one side of the catalog includes all of our Organic Certified
Reference Materials, and the flip side includes all of our Inorganic Certified
Reference Materials.
Therefore our customers can rely on these certificates not being used as a basis
to relax but as a stepping stone to new heights with regards to quality and
performance It is our aim to be a reliable partner to our customers in all
questions about pure gas technology with economical solutions to their individual
problems through well engineered technology
Our Organic Standards are used for GC, GC-MS,
HPLC, LC-MS, and other analytical instrumentation.
SPEX CertiPrep has been manufacturing reference materials since 1954 – that’s
more than half a century of dedication to serving the laboratory community with the
highest quality products available. Over the years, our product line has expanded as
technology improved. Our commitment to you will always remain our number one
goal.
The most important steps for the fulfilment of these expectations are:
• optical measurement control max 100%,
• microscopic and endoscopic test of all bored holes,
• multi-stage special cleaning with DI-water cleaning process, clean air
We specialize in manufacturing Custom Standards to meet or exceed your
specifications. Every stock and custom Certified Reference Material we manufacture
falls within the scope of our certification and accreditations.
flushing and material friendly drying,
• functional tests,
• 12-hour-pressure test at nominal pressure ,
• Helium-leakage-test with mass spectrometer
SPEX CertiPrep is a UL-DQS certified ISO 9001:2008 facility and
we are accredited by A2LA as complying with the requirements
of ISO/IEC 17025:2005 “General Requirements for the
Competence of Testing and Calibration Laboratories” and
ISO/IEC Guide 34:2009 “General Requirements for the
Competence of Reference Material Producers.”
• 100% function and tightness control of basic components
Every product we ship complies with all DOT and FAA requirements, using boxes
and packing materials that are designed to withstand the rigors of shipping. This
gives you the peace of mind that the product will not only be of the highest quality,
but also arrive at your facility in pristine condition. We recently changed our packing
materials so that it is not only safer, but greener. We are continually striving for a
greener facility; our most recent initiative includes the installation of 335 solar panels
on the roof of our Metuchen, NJ headquarters.
Tel : 0-2965-8971-3
Fax : 0-2965-8974
page : 30
C.E. Instruments (Thailand) Co., Ltd.
68/876 Moo 8, Rattanathibet Road, Bangkrasor, Muangnonthaburi,
Nonthaburi 11000, Thailand.
Tel : 0-2965-8971-3 Fax : 0-2965-8974

C a t l

Transcription

Similar documents

MedDX Thermacor Rigid Secondary Absorbent Clamshell

Intramuscular Injections How to Give Yourself STEPS:

New for 2016: PAL Decapper

Medizinische Austellung A4 Wien 2008.indd

bis tristar - LUCKINSlive

MAMAC SYSTEMS® Convinced that all temp sensors are same?

No Ice Packs… EVER AGAIN! - FRIO Insulin Cooling Case

Automated Vial Filling Systems

How to replace AD-DC power supply module for SheevaPlug GTI-2010.04.24

FTN-TP-070 3P LED Lamp