cv 3-200 e - Europower Components Ltd

Transcription

cv 3-200 e - Europower Components Ltd
Voltage Transducer CV 3-200
VPN =
140 V
For the electronic measurement of voltages: DC, AC, pulsed...,
with a galvanic isolation between the primary circuit (high voltage)
and the secondary circuit (electronic circuit).
0630
Electrical data
VPN
VPM
VS
KN
RL
CL
VC
IC
Primary nominal voltage rms
Primary voltage, measuring range
(Analog) secondary voltage @ VP maxi
Conversion ratio
Load resistance
Capacitive loading
Supply voltage (± 5 %)
Current consumption
140
0 .. ± 200
10
200 V / 10 V
≥1
≤5
± 15
32 + VS / R L
V
V
V
Overall accuracy @ VP maxi
VO
Offset voltage @ VP = 0
TA = 25°C
- 40°C .. + 85°C
TA = 25°C
- 40°C .. + 85°C
tr
Response time 1) to 90 % of VPN step
dv/dt dv/dt accurately followed
BW
Frequency bandwidth (- 1 dB) @ VPN
Maxi
± 0.2
± 0.6
± 5.0
± 13.0
0.3
200
DC .. 300
• Closed loop (compensated) voltage
transducer
kΩ
nF
V
mA
• Isolated plastic case recognized
according to UL 94-V0
• Patent pending.
Advantages
Accuracy - Dynamic performance data
XG
Features
%
%
mV
mV
µs
V/µs
kHz
•
•
•
•
•
•
Excellent accuracy
Very good linearity
Low thermal drift
Low response time
High bandwidth
High immunity to external
interference
• Low disturbance in common mode.
Applications
• AC variable speed drives and servo
General data
motor drives
TA
TS
P
R1
m
Ambient operating temperature
Ambient storage temperature
Total primary power loss
Primary resistance
Mass
Standards
- 40 .. + 85
°C
- 45 .. + 90
°C
3.1
W
6.4
kΩ
560
g
EN 50155: 1995
• Static converters for DC motor drives
• Battery supplied applications
• Uninterruptible Power Supplies
(UPS)
• Power supplies for welding
applications.
Application domain
Note:
1)
With a dv/dt of 200 V/µs.
• Traction.
Page 1/3
061219/10
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
w w w .lem.com
Current Transducer CV 3-200
Isolation characteristics
Vd
Ve
Rms voltage for AC isolation test, 50 Hz, 1 min
Partial discharge extinction voltage rms @ 10pC
6
2
dCp
dCl
CTI
Creepage distance
Clearance distance
Comparative Tracking Index (Group I)
83.8
76.4
600
kV
kV
mm
mm
Safety
This transducer must be used in electric/electronic equipment with respect to
applicable standards and safety requirements in accordance with the following
manufacturer's operating instructions.
Caution, risk of electrical shock
When operating the transducer, certain parts of the module can carry hazardous
voltage (eg. primary busbar, power supply).
Ignoring this warning can lead to injury and/or cause serious damage.
This transducer is a built-in device, whose conducting parts must be inaccessible
after installation.
A protective housing or additional shield could be used.
Main supply must be able to be disconnected.
Page 2/3
061219/10
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
w w w .lem.com
Dimensions CV 3-200
(in mm. 1 mm = 0.0394 inch)
Front view
Left view
Secondary terminals
Terminal
Terminal
Terminal
Terminal
+
M
0
-
:
:
:
:
supply voltage + 15 V
measure
0V
supply voltage - 15 V
Connection
Top view
Mechanical characteristics
• General tolerance
• Transducer fastening
Fastening torque maxi
• Connection of primary
• Connection of secondary
Fastening torque maxi
Remarks
± 0.3 mm
3 holes ∅ 5.5 mm
M5 steel screws
3.8 Nm or 2.80 Lb. -Ft.
M5 threaded studs
M5 threaded studs
2.2 Nm or 1.62 Lb. -Ft.
• VS is positive when VP is applied on terminal +HT.
• CEM tested with a shielded secondary cable.
Shield connected to 0 V at both ends, or disconnected.
• This is a standard model. For different versions (supply
voltages, turns ratios, unidirectional measurements...),
please contact us.
Page 3/3
061219/10
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
w w w .lem.com