Twin Fixture - Big Ass Fans

Transcription

INSTALLATION
GUIDE
Twin High Bay LED
For help, call 877-BIG FANS or
visit www.bigasslight.com/service
Questions?
Customers in the United States
For questions about your product, please contact a customer service representative
at 877-BIG FANS (877-244-3267) or visit www.bigasslight.com/service
Customers outside the United States
For questions about your product or customer service inquiries, please
contact your local Big Ass Light representative or fill out a contact form at
www.bigasslight.com/service
Installation Guide
January 2015
Rev. B
Model number:
BAL-HBL1-40XXXXXX
BAL-HBL1-52XXXXXX
Conforms to
UL Standard 1598, UL Standard 8750,
CSA Standard C22.2 No. 250.0, and
CSA Standard C22.2 No. 250.13
This product was manufactured in a plant
whose Management System is certified as
being in conformity with ISO 9001:2008.
May be protected by one or more of the following patents: www.bigasssolutions.com/patents
Contents
Introduction
Important Safety Information��1
Parts Included��2
Assembly
1. Position Fixtures Side-by-Side��3
2. Clamp the Fixtures Together��3
4. Open Enclosure��4
6. Screw Enclosure Onto Fixtures��5
7. Wire and Hang��5
Wiring
Basic Wiring��7
Wiring With External Dimming��8
Wiring With Onboard Dimming��9
Wiring With Onboard Occupancy Sensor��10
Defaults
Default Occupancy Sensor Settings��11
Maintenance Electrical Preventive Maintenance��13
Removing and Replacing the Lenses��13
Cleaning the Lenses��13
TWIN HIGH BAY LED © 2014 BIG ASS LIGHT, LLC. ALL RIGHTS RESERVED WWW.BIGASSLIGHT.COM
Introduction
1
This guide contains important instructions and safety information.
Leave these instructions with the owner after installation.
Important safety information
!
WARNING: Disconnect power before servicing.
!
WARNING: This product contains high intensity LED devices. To
prevent permanent eye damage, do not stare into the light beam at
close range.
!
The installation of Big Ass Light products must be performed by
qualified person(s) in accordance with all applicable codes. Code
compliance is your responsibility. Failure to comply with these codes
could result in personal injury or property damage.
Suitable for operation in ambient temperatures not exceeding 55°C.
Suitable for damp locations.
Not for use in dwellings.
Ensure power is routed to an approved outlet box at the ceiling before beginning
installation. Support the fixture so that it does not fall during installation.
2
Introduction (cont.)
Parts included
Note: Drawings below are not to scale.
(2) Single Fixture
Enclosure Assembly1
(1) Enclosure
(1) Power Cable
(1) Dimming Cable2
(4) 6-20 Pan Head Screw
(1) 3/4” NPT Cord Grip
(1) 3/4” NPT Lock Nut
(1) 3/4” NPT Conduit Hub
(1) 1/2” NPT Cord Grip
(1) 1/2” NPT Lock Nut
(2) 5-Conductor Splicing Connector
(4) 3-Conductor Splicing Connector
(7) 12” Wire, Assorted Colors (not shown)
Clamp Assembly
(4) Clamp Bracket
(4) 1/4-20 Hex Head Screw
(4) 1/4-20 Hex Nut
(2) Y Cable, 20 ft (6 m)
1. Installation may not require all provided parts. See the assembly and wiring
instructions for details.
2. Not provided if occupancy sensor is included with the enclosure.
Assembly
3
1. Position fixtures side-by-side
Make sure same-size holes are aligned as shown.
2. Clamp the fixtures together
Make sure the clamp brackets fit snugly. If they are loose, rotate one bracket and
fit them back together as shown.
Make sure fit is snug
Brackets should fit snugly
If misaligned, rotate one bracket
Slide a pair of clamp brackets out to the endcap. Clamp as shown, tightening to
approximately 12 in·lb (1.4 N·m). Repeat on the other end of the fixture.
Clamp assembly hardware
a. (4) 1/4-20 Hex Nut
b. (4) 1/4-20 Hex Head Screw
c. (4) Clamp Bracket
Clamp at endcap
a
c
TWIN HIGH BAY LED © 2014 BIG ASS LIGHT, LLC. b
b
ALL RIGHTS RESERVED WWW.BIGASSLIGHT.COM
4
Assembly (cont.)
4. Open enclosure
Remove screws as shown to remove the endplates and top panel of the
enclosure. Note: Reserve screws to reassemble the enclosure after wiring.
OR
5
Assembly (cont.)
6. Screw enclosure onto fixtures
Position the enclosure and fixtures so corresponding holes and knockouts are
aligned as shown below. Screw the enclsoure to the fixtures.
Enclosure hardware
a. (4) 6-20 Pan head screw
Align knockouts and holes
a
Power (3/4” NPT)
Dimming (1/2” NPT)
7. Wire and hang
!
WARNING: Do not use conduit to support the weight of the fixture.
Always hang twinned fixtures using the provided cables.
Secure the 12” (30 cm) green wire in the ground lug inside the enclosure.
Refer to the following instructions to wire the fixture:
Basic Wiring��7
Wiring With External Dimming��8
Wiring With Onboard Dimming��9
Wiring With Onboard Occupancy Sensor��10
After wiring the fixture, close the enclosure and secure with reserved screws.
Hang the fixture at least 2 ft (0.6 m) from the ceiling using the provided cables.
Wiring
7
Basic wiring
L1
GROUND (GREEN)
Facility Power
L2
Enclosure Ground Lug
GROUND
Remove enclosure knockouts as needed. Connect as shown below.
GROUND (GREEN)
GROUND (GREEN)
Fixture
L2 (WHITE)
L2 (WHITE)
L1 (BLACK)
L1 (BLACK)
Fixture’s L1 (black)
connects to
Fixture’s L2 (white)
connects to
120 VAC, 1 Ф derived from
1 Ф, 240/120 V panel
H (black)
N (white)
3 Ф, 208/120 V panel
L1 (black), L2 (red), or
L3 (blue)
L2 (red), L3 (blue), or
L1 (black)
1 Ф, 240/120 V panel
L1 (black)
L2 (red)
3 Ф, 240/120 V panel, B phase
wild
L1 (black), L2 (orange), or
L3 (blue)
L2 (orange), L3 (blue),
or L1 (black)
3 Ф, 480/277 V panel
L1 (brown), L2 (orange), or
L3 (yellow)
N (white)
3 Ф, 600/347 V panel
L1 (red), L2 (black), or
L3 (blue)
N (white)
3 Ф, 480/277 V panel
L3 (yellow)
L2 (orange), L3 (yellow),
or L1 (brown)
3 Ф, 480 V panel, corner ground
L1 (brown) or L3 (yellow)
L2/Grounded conductor
(white or gray)
All
Low voltage fixture
(120–277 V ± 15%)
Supply voltage
High voltage fixture
(347–480 V ± 15%)
Fixture
8
Wiring (cont.)
Wiring with external dimming
L1
GROUND (GREEN)
Facility Power
L2
GROUND
Enclosure Ground Lug
GROUND (GREEN)
GROUND (GREEN)
L2 (WHITE)
L2 (WHITE)
L1 (BLACK)
L1 (BLACK)
DIM+ (VIOLET)
DIM+ (VIOLET)
DIM- (GRAY)
DIM(GRAY)
Facility Dimming (1–10 V DC)
Fixture’s L1 (black)
connects to
Fixture’s L2 (white)
connects to
1 Ф, 120/240 V panel
H (black)
N (white)
3 Ф, 120/208 V panel
L3 (blue)
L1 (black)
1 Ф, 120/240 V panel
L1 (black)
L2 (red)
240 VAC, 1 Ф derived from 3 Ф,
120/240 V panel, B phase wild
L3 (blue)
L2 (orange), L3 (blue),
or L1 (black)
3 Ф, 277/480 V panel
L3 (yellow)
N (white)
3 Ф, 347/600 V panel
L1 (red), L2 (black), or
L3 (blue)
N (white)
3 Ф, 277/480 V panel
L3 (yellow)
L2 (orange), L3 (yellow),
or L1 (brown)
3 Ф, 480 V panel, corner ground
L1 (brown) or L3 (yellow)
L2/Grounded conductor
(white or gray)
All
Low voltage fixture
(120–277 V ± 15%)
Supply voltage
High voltage fixture
(347–480 V ± 15%)
Fixture
DIM- (GRAY)
DIM+
(VIOLET)
Fixture
Wiring (cont.)
9
Wiring with onboard dimming
Refer to the example illustrations below to determine where to place your dimmer
along the center wall of the enclosure so that the dimming and power wires
remain on their respective sides. Remove the corresponding knockout in the
center wall and secure the dimmer in place.
Connect the fixture to power as shown on page 5.
Wire and configure the dimmer according to the dimmer manufacturer’s instructions.
10
Wiring (cont.)
Wiring with onboard occupancy sensor
120/277 V fixtures only
Fixture
GROUND (GREEN)
L2 (WHITE)
DIM+ (VIOLET)
L1 (BLACK)
DIM- (GRAY)
Occupancy Sensor
Facility
Power
LOAD (RED)
DIM+ (VIOLET)
L1
LINE (BLACK)
L2
NEUTRAL (WHITE)
DIM- (GRAY)
GROUND
(GREEN)
GROUND
GROUND (GREEN)
Fixture
Enclosure
Ground Lug
L1 (BLACK)
L2 (WHITE)
GROUND (GREEN)
DIM+ (VIOLET)
DIM- (GRAY)
Sensor’s Line (black)
connects to
Fixture’s L2 (white) and
sensor’s Neutral (white)
connect to
1 Ф, 120/240 V panel
H (black)
N (white)
3 Ф, 120/208 V panel
L3 (blue)
L1 (black)
1 Ф, 120/240 V panel
L1 (black)
L2 (red)
3 Ф, 120/240 V panel, B phase wild
L3 (blue)
L2 (orange), L3 (blue), or
L1 (black)
3 Ф, 277/480 V panel
L3 (yellow)
N (white)
Supply voltage
Default Occupancy Sensor Settings 11
Occupancy sensors are programmed with the following default settings:
High Mode..................... 10 V
Sensitivity...................... Max
Low Mode ..................... 1 V
Setpoint......................... None
Time Delay.................... 5 min
Ramp Up....................... None
Cut Off........................... 1 hr
Fade Down.................... None
Force Off Setpoint with Occupied..................................................Disable
Note: Because Setpoint is set to “None,” lights will return to full brightness
whenever the sensor detects motion.
These settings can be modified at any time using the handheld remote
programming device. For further assistance, contact Customer Service.
Maintenance
13
Electrical preventive maintenance
Big Ass Light suggests an electrical preventive maintenance program similar to
that described in NFPA 70B: Recommended Practice For Electrical Equipment
Maintenance by the National Fire Protection Association.
Removing and replacing the lenses
The lenses are designed to be removable for cleaning or replacement. Note:
Handle lenses with care.
To remove a lens, grasp the end grip and gently slide the lens out as shown.
To insert a lens, slide in and push firmly until the grip is flush with the edge of
the fixture.
Cleaning the lenses
!
CAUTION: Do not clean the fixture—especially the lenses—with
scouring pads, alkaline cleaning substances, gasoline, thinner,
benzene, heating oil, glycol, alcohol, or polishing powder.
!
CAUTION: Do not pressure wash or use a water hose to clean the
fixture.
Clean the lenses periodically to ensure optimal performance. Remove lenses
and wipe with a clean, damp cloth. Allow to dry thoroughly before replacing. If
necessary, use a mild soap or a gentle liquid cleaner.
BAL-INST-34-MUL-01
REV B
2425 Merchant St., Lexington, KY 40511
1 (877) BIG-FANS | WWW.BIGASSFANS.COM

Twin Fixture - Big Ass Fans

Transcription

Similar documents

wannabe - Moda Light

Murray Feiss OL7411ASTB

Bitron AV1407/001 (4+n) T-Line

LED CANOPY LIGHT - WIDE DISTRIBUTION 38-WATT LED (E-CC3L SERIES)

BAYTEK

Lumewave TOP900-TL by Echelon TOP900-TL: Wireless Control Lighting Module

DM1200 - Times Square Stage Lighting

Fermax Citymax 8039 Universal

integrated furnace controls nitride hot surface ignition controls (hsi)

USSA > University of Pretoria - University of Pretoria Archived Website