GIRDER INSTR W:WaveW

Transcription

GIRDER INSTR W:WaveW
TURN ZAYANTE CRANK SPEC & COMPATIBILTY
TURN GIRDER
M30 MTB CRANK
FRAME SHELL
68/73 MM MTB BSA FRAMES, BB92 MTB, 73MM BB30 or PF30 MTB frames.
BOTTOM BRACKET
Praxis Works M30 BB for BSA, M30 Conversion BB30/PF30
FRONT DERAILLEUR
BCD
SAFETY INFORMATION
Since specific tools and experience are necessary for proper installation, it is recommended that the product be installed by
a qualified bicycle technician.
Read the service instructions foryour crank carefully prior to installing the parts. Loose, worn or damaged parts may cause
riding problems and serious injury may occur as a result. If installation and adjustments are not carried out correctly, the
chain may come off and this may cause you to fall off the bicycle which could result in serious injury. Read these
instructions carefully, and keep them for later use.
•
•
•
•
•
•
•
•
•
•
•
•
WARRANTY
•
•
•
•
•
•
TURN products are warranted to be free from defects in materials or workmanship for two years after
original purchase. The warranty is non-transferable and valid to the original purchaser of the product only.
Any attempt to modify the product in any way such as drilling, grinding, painting, or changing out bearings
will void the warranty.
This warranty is not valid for “abused” or neglected products, or products that are damaged by improper
installation.
If a defect is found, our entire liability and your sole remedy shall be, at our option, free repair or
replacement of the Praxis product.
Parts are not guaranteed against natural wear or deterioration resulting from normal use.
Except as expressly required by law, Praxis Works shall not be held liable for any indirect, special, or
consequential damages.
THIS WRITTEN EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, IMPLIED OR EXPRESSED. This
warranty gives you specific legal rights, and you may also have other rights which vary state to state. For more
information on warranty policy and instructions for completing a warranty claim, check out the Full Warranty
Policy found at our website. www.praxis-works.com
Etype only with BSA frames
104/64 2X
104 1X
CRANK ARM LENGTH
165, 170, 175, 180
CHAIN
10 or 11 speed KMC, Shimano
q w e
Be careful not to let your clothing get caught in the chain while riding, otherwise you may fall off the bicycle.
Check that the tension of the chain is correct and that the chain is not damaged. If the tension is too weak or the chain
is damaged, the chain should be replaced. The chain may break and you may fall off the bicycle if this is not done.
Use a torque wrench to check the final tightening torque of the main crank bolt and chairing bolts. Furthermore, after
riding approximately 100 km (60 miles), use a torque wrench to re-check the tightening torques. Main Crank bolt =
Torque 48-52nm. Chainring Bolts = Torque 8-10nm.
If the bottom bracket shell is not parallel, shifting performance will be affected and performance will drop.
Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank arm may
break and you may fall off the bicycle.
Before riding the bicycle, check that there is no play or looseness in the bottom bracket connection. Also, be sure to
retighten the crank, chain ring bolts, and pedals at periodic intervals.
If you feel any looseness or ‘play’ in the bearings, the bottom bracket should be inspected/replaced.
For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a
professional bicycle dealer or call Praxis Works.
Praxis Works assumes no responsibility for damages or injury related to improperly installed components.
To ensure the designed performance, only use 10 or 11sp chains by KMC, Shimano, or Campagnolo.
If the chain keeps coming off the chainrings during use, replace the chainrings and chain.
READ THE STEP BY STEP INSTRUCTIONS PROVIDED ON THE OTHER SIDE.
Braze On or ST clamp
r ty
u
i
o
28MM
30MM
1.
2.
3.
4.
5.
Non-Drive Crank Arm
Non-Drive Cup 28MM ID Outer Seal
Non-Drive Cup (BSA Threaded shown)
Drive Cup (BSA Threaded shown)
Drive Cup 30MM ID Outer Seal
30MM
6. Drive 30MM ID Wave Washer
7. Male ring bolts
8. Chain ring
9. Drive Crank Arm
10. Female ring bolts (Torque 8-10nm)
︎ CHAIN RING INSTALLATION
RING MARKS MUST BOTH
FACE INWARD AND ALIGN
WITH DRIVE CRANK ARM
The Praxis Works chain rings are
matched sets and smooth shifting will
not be possible if the chainrings are
incorrectly installed. Be sure to install
the chainrings in the correct positions as
the graphic shows.
CROSS GEARING SMALL/SMALL➡︎
When the chain is in the position shown
at the right, the chain may contact the
front chainrings or front derailleur and
make noise. If the noise is a problem,
shift the chain onto the next-larger rear
sprocket or the one after.
CROSS GEARING
a
GREASE HERE
INSTALLATION OF CRANKSET
NEEDED TOOLS:
M30 BSA BB - One M30 socket tool is needed.
M30 CONVERSION BB - Two M30 BB tools are required for correct installation.
For removal, use same M30 BB tool to unscrew the Drive cup first, but also a
‘Cup’ removal tool for when removing the pressed NonDrive Cup.
M30 Socket
Tool
Zayante M30 can be installed with any of these 3
Praxis M30 Bottom Brackets
M30 BSA
ENGLISH THREADED
1.
First slide the Drive side Wave Washer onto
the spindle.
Next slide on the 30mm ID seal with the
Praxis word mark facing out/away from the
frame.
Now insert the crankset into the Drive cup
and push spindle through bottom bracket.
M30 PF30
CONVERSION BB
(Add delrin sleeve)
M30 BB30 / PF30
CONVERSION BB
M30 BB30
CONVERSION BB
2.
3.
Slide the Non-Drive 28mm ID seal onto
the spindle, with the Praxis word-mark
side facing out/away from the frame.
M30 BSA
ENGLISH THREADED
Use an 8mm hex torque wrench and tighten
the Non-Drive crank arm bolt to 48-52Nm.
Spin crank to make sure it moves freely.
Note: specifications are subject to change without notice. © October 2013 by Praxis Works, LLC
820 Swift Street Suite B. Santa Cruz, CA 95060
.