PermaWrap MC Technical
Transcription
BETTER MOISTURE MANAGEMENT - PROVIDES EFFECTIVE MOISTURE MANAGEMENT - ALLOWS FOR DRAINAGE OF WATER BEHIND CLADDING - DRAINAGE CHANNELS WILL NOT CRUSH - ACTS AS A WEATHER RESISTANT BARRIER - RESISTS TEARING - USE BEHIND SIDING, STUCCO, AND STONE - ALLOWS MOISTURE VAPOR TO ESCAPE - EASY INSTALLATION - LIGHT WEIGHT - AVAILABLE WITH CUSTOM LOGO PRODUCT SPECIFICATIONS WOVEN POLYPROPYLENE COMPOSITION 1.9 OZ/YD2 (+/- 5%) WEIGHT AVG 5.0 MILS THICKNESS TENSILE STRENGTH MD 53 LB CD 44 LB TEAR STRENGTHM D 21 LB CD 19 LB WATER RESISTANCE PASS MTVR/PERMS 12 - 15 PERMS UV RESISTANCE 9 MONTHS CLASS A FIRE RATING >90% DRAINAGE EFFICIENCY ROLL SIZES WIDTH 9' 10' TEST METHOD ASTM D 751 ASTM ASTM ASTM ASTM D 5034 D 5587 D 779 E 96A ASTM E 84 ASTM E 2273 LENGTH (ROLLS/PALLET) 100' (78), 150' (55), 195' (45) 100' (78), 150' (55), 195' (4) PermaWrapMC has been tested and meets or exceeds all relevant requriements of ICC-ES AC38, “Acceptance Criteria for Water Resistive Barriers.” MVTR - Moisture Vapor Transmission Rate (Perm Rating). Microperforated housewrap relies on tiny punctured holes to control vapor transmission properties, these holes vary in size which means MVTR is taken based on an average. Surpasses ASTM AC-10 criteria, and perform exceptionally for home moisture protection. Durability of a material after the long extraneous exposure to UV rays. This is an average. UV impact will vary across the US, which could prolong or shorten maximum UV life. Our recommended time period covers these variances. Handling and Storage When stored outdoors, PermaWrapMCTM must be protected from exposure to direct sunlight using a light colored tarp. Material that has been unwrapped should be covered or rewrapped. PermaWrapMCTM is made of synthetic materials that are recognized as not providing a food source for mold, mildew, fungus, or insects. It should always be properly installed and stored. For installation instructions please visit our website www.permaproducts.com for house wrap installation instructions. 800 647 6130 • PO Box 279 • Grenada, MS 38902 www.permarproducts.com
Similar documents
Willseal 600 ASTM E-84
Description willseal 600 is a precompressed, selfexpandinq polyurethone foam joint sealant that is designed to seal against rain, wind, sound, draft and dust. Unlike other conventional meth ods, willseal 600 is not susceptible to breakdowns caused by excessive joint movements, joint strain, surface contamination, aging and general tensile stress-caused failures. It does not dry out, shrink or deteriorate. There's no mixing, no masking, no staining and no mess, willseal 600 can be installed under many weather and temperatureconditions. Material Open cell polyurethone flexible foam impregnated with a flame retardant modified acrylic. Supplied precom pressed with PSA on one side. Tested Physical Properties illbruck willseal 600 Property Test Method Value Color Black/Grey Density ASTM D 3574 5.5-6.5 Ib/ft3l90-110kg/m3) ThermalConductivity ASTMC518 0.28 - 0.30 Btu-in/hr.=F-ft2 Thermal Resistance ASTM C 518 3.3 - 3.6 hr-^F-flVBtu Tensile Strength ASTM D 3574 21 psi min. TemperotureStability Range Short Term LongTerm -40°C/-40°F to 120°C/248°F - 40°C/-40°F to 90°C/194"F Elongation ASTM D 3574 120%+/-20% Compression Set ASTM D 3574 4.2% max. Staining and Bleeding DIN 18 542 Meets DIN requirements Resistonce to UV and Moisture DIN 18542 Meets DIN requirements Shelf Life 2 years Water Resistance ASTM E 331 12 psf ASTM E 547 12psf Fire Testing ASTM E 84' Flame Spread;0, Smoke Developed: 5 Compatibility with conven tional construction materials DIN 52423 Nosigns ofcorrosion wereobservedon zinc, steel,galvanizedsteel,aluminium and copper; no odverse effects with concrete, aerated con crete, brick,some natural stone, PVC,Plexiglos ond wood; for other materials consultillbruck Ideal Storage Temperature 34 °F-68°F Performance Guorantee 10 year worronty^ on performance
More information