technical service information package my08 nissan armada

Transcription

technical service information package my08 nissan armada
®
TECHNICAL SERVICE
INFORMATION PACKAGE
MY08
NISSAN ARMADA (WZW) &
INFINITI QX56 (IWZW)
BOSE® MUSIC SYSTEM
Preliminary Document
UNCONTROLLED DOCUMENT- 02/07
General reference for Service Use Only
BOSE® MUSIC SYSTEM
Nissan Armada (WZW) / Infiniti QX56 (iWZW)
Introduction:
The Bose® Music System is custom tailored to match the specific acoustic characteristics of this
vehicle’s interior.
Content (See “Service Configuration and Recommendation” for part numbers):
Center IP:
(1) 3.25” Twiddler
Front IP
(2) 2.5” Twiddler
Front Doors:
(2) 6x9” Speaker
Under Drivers
Seat
(1) 8.3 Liter enclosure with a 5.25” Woofer
powered by a 100W TSM amplifier
Rear Doors:
(2) 6.5” Speaker & (2) 1.5” Twiddler
Rear Lift gate
(2) 3.25” Twiddler
Under Drivers
side IP
A Bose centralized, 8 channel, high performance Power
Amplifier with active equalization network and compression
circuitry. Amplifier also uses noise compensation technology.
Also In I.P.
Radio Head Unit
For Radio unit service please contact the Radio Manufacturer.
Radio Supplier -
H/U with Navi
H/U without Navi
XANAVI ( Audio supplied by Clarion to XANAVI)
Panasonic
The active equalization network takes into account the absorptive and reflective characteristics of
seats, windshield, seat coverings, instrument panel and door shapes,
speaker placement, and occupant placement.
To achieve the best performance of the sound system all tone controls should be set at the detent
position
Service:
Service will be limited to the replacement of the component parts listed in the “System
Configuration and Service Recommendation”, found later in this technical information package. No
internal amplifier repair or speaker repair is permitted in the field. Because of the uniqueness in
the custom acoustics of the equalization network, no external customer modifications are
recommended or sanctioned (I.E. graphic equalizers, additional sub-woofers, or additional power
amplification).
Any modifications to the system will void the warranty of the system components.
The enclosed technical and diagnostic information should serve as adequate source
material for the creation of dealer technical service information materials. If any additional
information is required, please direct inquiries to the attention of:
Dave Gustafson
Supervisor North American Service
Bose Corporation
Internet: [email protected]
The Bose ® Sound System
for the 2008 Infiniti QX56 and Nissan Armada
Twelve high-performance
speakers
1
2
Two 2.5-inch (64mm) Twiddler® mid/high-range
speakers, one on each side of the instrument panel.
One 3.25-inch (80mm) Twiddler neodymium
mid/high-range speaker in the middle of the
instrument panel.
3
Two 6 x 9 inch (150 x 230mm) wide-range
speakers, one in each front door.
4
One 5.25-inch (130mm) high-performance
Richbass® woofer in an 8.3-liter customized bassreflex enclosure under the driver’s seat, powered
by a Bose® 100-watt two-state modulation amplifier.
2
1
1
3
3
8
4
5
5
6
5
Two 1.5-inch (36mm) tweeters, one in each
rear door.
6
Two 6.5-inch (165mm) high-performance
neodymium speakers, one in each rear door.
7
Two 3.25-inch (80mm) Twiddler neodymium
mid/high-range speakers, one on either side of
the rear liftgate.
6
System Electronics
8
A Bose® digital amplifier with eight channels of
customized equalization and digital signal
processing mounted behind the driver’s-side
instrument panel.
7
7
5
Main Amp (8800)
18 W
18 W
18 W
100 W
37 W
37 W
37 W
37 W
1
2
3
4
5
6
7
8
Note: The 100 W output on
Channel 4 is achieved after
the amplification of the Bass
Box TSM amplifier
TSM
8 Channel
8800 Amp
3
3.25"
4 Ohm
2.5"
4 Ohm
2.5"
4 Ohm
Radio
5
6
6x9"
2 Ohm
6x9"
2 Ohm
4
1.5"
4 Ohm
100W TSM Amp
5.25" ½ Ohm Spk
1.5"
4 Ohm
7
8
6.5"
2 Ohm
6.5"
2 Ohm
3.25"
4 Ohm
3.25"
4 Ohm
1
2
MY08 Nissan Armada / Infiniti QX56
BOSE 8800 Series Amplifier
Quad Power IC
B+
11
Sw B+
31
GND
12
+
32
18
Channel 1 input
Left Front
Channel 1 output
Left lift gate
6
7
Channel 2 output
Right lift gate
37
27
Channel 3 output
Center IP
15
28
Channel 4 output
Under drivers seat
9
14
GPIO D
Bass Box Amp Control
+
+
-
+
+
-
+
-
25
Duel Power IC
20
19
22
21
33
21
+
GPIO A
Centerpoint
On/Off
+
35
Channel 2 input
Right Front
Channel 3 input
Left Rear
Channel 5 output
Left front door / Left IP
4
5
Channel 6 output
Right front door / Right IP
8
13
+
-
+
-
Duel Power IC
Channel 4 input
Right Rear
Channel 7 output
Left rear door
1
10
Channel 8 output
Right rear door
2
3
+
-
+
-
MY08 Nissan Armada / Infiniti QX56 Connector pin assignment
Amplifier pin assignments
Channel assignment
Output 1 - Left Liftgate
Output 2 - Right Liftgate
Output 3 - Center IP
Output 4 - Bass Box
Output 5 - Left Front Door
Output 6 - Right Front Door
Output 7 - Left Rear Door
Output 8 - Right Rear Door
PIN
FUNCTION
PIN 1
OUTPUT 7+
PIN 2
OUTPUT 8+
PIN 3
OUTPUT 8PIN 4
OUTPUT 5+
PIN 5
OUTPUT 5PIN 6
OUTPUT 1+
PIN 7
OUTPUT 1PIN 8
OUTPUT 6+
PIN 9
OUTPUT 4+
PIN 10
OUTPUT 7PIN 11
B+
PIN 12
GND
PIN 13
OUTPUT 6PIN 14
OUTPUT 4PIN 15
OUTPUT 3+
PIN 16
N/C
PIN 17
N/C
PIN 18
INPUT 1+
PIN 19
INPUT 2+
Bass Box pin assignments
5
4
3
2
6
PIN
1
2
3
4
5
6
1
FUNCTION
WOOFER WOOFER +
NO CONTACT
AMP ON
POWER GND
BAT
PIN
PIN 20
PIN 21
PIN 22
PIN 23
PIN 24
PIN 25
PIN 26
PIN 27
PIN 28
PIN 29
PIN 30
PIN 31
PIN 32
PIN 33
PIN 34
PIN 35
PIN 36
PIN 37
FUNCTION
INPUT 2INPUT 3+
INPUT 3INPUT 4+
N/C
GPIO_D OUT (Bass box enable)
N/C
OUTPUT 2OUTPUT 3N/C
N/C
SWB+ (Amp enable)
INPUT 1INPUT 4N/C
GPIO_A INPUT (Centerpoint On/Off)
N/C
OUTPUT 2+
®
AUTOMOTIVE SYSTEMS DIVISION SERVICE
SYSTEM CONFIGURATION AND SERVICE RECOMMENDATION
AS OF: 02/07
CODE NAME /MODEL: WZW & iWZW / MY 08 Nissan Armada & Infinfiti QX56
PRODUCTION PART NUMBERS
CONFIGURATION
DESCRIPTION
Center IP
BOSE P/N
CUSTOMER P/N
SERVICE
3.25" Twiddler Speaker
275055-1002C
28154 5Z200
(1) (2) (3)
Left IP
2.5" Twiddler Speaker
266048-102C
28152 7S200
(1) (2) (3)
Right IP
2.5" Twiddler Speaker
266048-102C
28152 7S200
(1) (2) (3)
Left Front Door
6" x 9" Speaker
265174-003C
28157 7S200
(1) (2) (3)
Right Front Door
6" x 9" Speaker
265174-003C
28157 7S200
(1) (2) (3)
Under Drivers Seat
8.3 Liter Bassbox (5.25" Spk & 100W TSM Amp
Service assembly
265215-004C
270516-003F
28170 7S200
28170 7S200
(1) (2) (3)
Left Rear Door
6.5" Speaker
1.5" Tweeter
260274-103C
265675-103C
28156 7Y300
28138 EA50A
(1) (2) (3)
Right Rear Door
6.5" Speaker
1.5" Tweeter
260274-103C
265675-103C
28156 7Y300
28138 EA50A
(1) (2) (3)
Rear Liftgate
Two 3.25" Twiddler Speakers
275055-1202C
28154 5Z20N
(1) (2) (3)
Behind Driver side IP
8800 Series Amplifier
295285-003C
28060 ZQ30A
KEY TO SERVICE ACTIONS:
(1) = SERVICED AT ASSEMBLY LEVEL WITH A "NEW" SERVICE REPLACEMENT PART
(2) = NO INTERNAL FIELD REPAIR AUTHORIZED
(3) = UNAUTHORIZED FIELD MODIFICATIONS (CUSTOMIZATIONS) ARE PROHIBITED
MY 08 Nissan Armada / Infiniti QX56 Part Identification Sheet
Left & Right IPs - 2.5" Twiddler
Rear Doors - 6.5" Speaker
Center IP - 3.25" Twiddler
Rear Doors - 1.5" Tweeter
Front Doors - 6 x 9" Speaker
Under Drivers seat - 8.3 Liter Bass Box
Behind Drivers side IP - 8 Channel Amplifier
WHO IS RESPONSIBLE
When there is a Field Service Problem
with the Bose® Music System?
AUTO MANUFACTURER’S
SERVICE PARTS
OPERATION
• Sells Bose Service Parts
• Sells New Radios
RADIO MANUFACTURER
AUTOMOBILE
CONSUMER
• Radio Sales
• Radio Service and Repair
• Technical Assistance
• BRINGS CAR INTO DEALER
AUTO DEALERSHIP
SERVICE DEPT.
• Originates Repair Order
• System Diagnosis & Repair
AUTO MANUFACTURER
DIVISIONAL SALES DEPT.
• Initiates Service Policies and
Procedures
• Assists Dealer w/ Consumer
complaints and problems
AUTO MANUFACTURER’S
TECHNICAL ASSISTANCE
• Assists Dealer to resolve difficult
problems
• Contacts Component Supplier when
they need help
BOSE CORPORATION
TECHNICAL ASSISTANCE
• Assist Auto Manufacturer to resolve
difficult Dealer technical problems
®
AUTOMOTIVE SYSTEMS DIVISION SERVICE
MY08 Nissan Armada / Infiniti QX56
SYSTEM PART-->
OX
WHOLE SYSTEM APPEARS DEAD-HOWEVER...
(Radio Head Functions SEEM to be OK)
POP NOISE WHEN RADIO IS TURNED ON OR OFF
O O
O
O
V
FX
OX
GV
SF
OX
FH
REDUCED SOUND FROM ONE CHANNEL
HRF
ATTENUATED SOUND FROM ONE CHANNEL
OX
GV
SF
OX
GV
SF
HRF
DISTORTED SOUND FROM ONE CHANNEL
(Buzzing, Scratchy, or Raspy sound)
F
H H
HRG
(-)Sh
HR
H Sh(-)H
HF
F
(Switch pops, ignition, and alternator
REAR LIFTGATE SPEAKERS
REAR DOOR SPEAKERS
FRONT DOOR SPEAKERS
BASS BOX SPEAKER
KEY:
O = Open
X = Shorted
S = Short to Shield
G = Grounded
V = Short to Voltage
R = Reversed Polarity
F = Failed Component
G(-) = Grounded Audio (-)
H= High Resistance
(Corrosion)
Sh = Open Shielding
PROCEDURAL SUGGESTIONS & HINTS
•Look for problem centered around radio Head
•Ensure Amp connector is plugged into Amp
•Amp will not turn on without switched B+ supplied
•Check Amp B+ and Ground circuits
•Radio Head must have uniterupted B+ to
maintain Memory Settings
F
•Check if Amp is ON when Radio is OFF
•Check Radio for Noisy Power Up/Down
Try substitute known good Radio unit
F
F
F
F
F
F
F
•Verify Condition w/ Fader and balance Ctrls
* Check audio wiring for the speaker
F
F
F
F
F
F
F
•Check for disconnected speaker connector
and/or open circuit at the speaker
F
F
F
F
F
F
F
•Verify condition w/ Fader and balance Ctrls
•Check for High resistance connections
F
F
F
F
F
F
F
•Check for loose trim panels or associated
local assemblies or harnesses & connectors
•Switch speaker to opposite channel, if prblm
moves w/ speaker, replace speaker.
•Try known good Bose Power Amp.
•Try known good Radio Unit
F
F
•Verify condition with Radio Balance Control
•One of the Amp's output IC's most likely
have shut down. Check for a wiring problem
before replacing the Bose Amplifier
F
•Substitute a known good radio unit
•Check for loose trim panels or associated
local assemblies or harnesses & connectors
•Check polarity of circuits in concern
•Check for loose conections & corrosion
Use "Reduced Sound Quality" Chart
ON WHOLE SYSTEM
NOISE AND INTERFERENCE
LEFT, RIGHT & CENTER IP SPEAKERS
F
F
OX
GV
SF
NO SOUND FROM COMPLEMENTARY CHANNELS
(Output IC configurations)
Channel 1, 2, 3 & 4
Channel 5 & 6
Channel 7 & 8
BOSE AMPLIFIER
RADIO HEAD UNIT
F
XOF
O
COMPONENTS
FUSE•BOSE POWER AMP FEED
FUSE•MEMORY BACKUP FEED
O
NO SOUND FROM ONE CHANNEL-DEAD
(All other channels sound OK)
REDUCED SOUND QUALITY ON MULTIPLE
CHANNELS OR POOR OVERALL SOUND
FUSE•RADIO
BOSE AMP• AUDIO OUTPUT CIRCUIT
BOSE AMP•AUDIO INPUT CIRCUITS
BOSE AMP•POWER GROUND CIRCUIT
BOSE AMP•B+ CIRCUIT
RADIO•GND CIRCUIT
FUSES
O O
WHOLE SYSTEM APPEARS DEAD
(Radio Head Functions DO NOT Operate/Luminate)
RADIO LOOSES MEMORY PRESETS
RADIO•IGN+ CIRCUIT
RADIO• BAT+ (MEM BACK UP) CIRCUIT
SYMPTOM
TROUBLESHOOTING GUIDE
CIRCUITS
F
F
•Check for proper suppression @ noise source
•Check proximity of wiring to noise source
•Check for open audio shielding
All Speakers
Check power
circuit, fuses,
wiring, and ground
No Audio
Is there proper battery
voltage? Is there a
display?
Possible Defective
Bose Amplifier
Replace Bose
Amplifier
Call
Technical
Assistance
Less than All
Speakers
Problem
Resolved?
Check for display
functionality
Possible Defective
speaker. Swap with like
speaker to verify.
Possible Loose
Connector at
Speaker
Shorted speaker
harness, should
measure open to
ground
Speaker
Defective
Amplifier
Defective
Connector
Damaged
One Channel No Output
Wire
Harness
Damaged
Loose
Connector
Amplifier
Defective
Speaker
Defective
Wire
Harness
Damaged
One Channel Static or
Popping
Loose
Connector
Loose
mounting
screws or
tabs
Defective
Speaker
Defective
Amplifier or
Radio
Poor Sound
Quality1
Loose
Connector
Insufficient radio
transmission for
vehicle location.
Compare to another
vehicle.
Wire
Harness
Damaged
If signal is
weak
ensure
proper
antenna
connections
Poor Radio
Reception
Antenna
wire
shielding
should be at
ground
potential
If signal is
sufficient at
radio try
changing
radio unit.
1
Providing a confirmed defect
Defective Speaker
Measure speaker wires for correct resistance (see
system layout diagram page.)
If speaker is presumed defective try swapping with a
known good speaker.
Also check for creases in cone or surround, replace if
creased.
Defective Amplifier
The system consists of one main 8 channel amplifier.
For one distorted channel try swapping speakers to confirm defective
part.
Note that the amplifier requires both a battery voltage and a SW
B+ voltage for the amplifier to turn on - Make sure both voltages
are present.
Connector Damaged or Loose
For switching noises:
Determine which speaker noises are coming from.
Substitute known "quiet" device for the noisy device. If
condition is corrected replace device.
See also, "No Audio" chart
Thermal intermittent problems may take several minutes to
occur. To reproduce try playing audio system at loud volumes
for several minutes.
If noise is heard in all modes (AM,FM,CD) check wire
harness to ensure proper connections. If only with AM or
FM ensure antenna circuit is ok per antenna test page.
In connectors (amp & radio) check connector terminals may
be loose or bent over. Shake connector while powered for
intermittent problems.
Antenna Circuit Issues
Check antenna measurements according to antenna
diagram.
If possible connect a known good antenna to test.
Note whether the problem occurs in all radio modes (AMFM-CD)
If possible measure signal strength or look for "stereo"
indicator in display.
Damaged Wire Harness
If single speaker defective check wires going to
suspect speaker for damage to insulation. If
possible disconnect both ends of harness and
measure resistance. (try flexing harness while
measuring)
If radio does not turn on check power (B+ &
ground) connections at amp and radio, also
checking switched B+. B+ should be 14V with
ignition on.
Front IP
Speakers
Rear Liftgate
Speakers
Front & Rear
Door Speakers
Front Doors
Main Amp
Left IP
2.5"
4 Ohm
Main Amp
6x9
2 Ohm
Main Amp
Left
3.25"
4 Ohm
Center IP
3.25"
4 Ohm
Right IP
Rear Doors
6.5"
2 Ohm
2.5"
4 Ohm
Front IP’s should read approximately 4
ohms across speakers and open to ground
Front & Rear Door’s should read
approximately 2 ohms across speakers and
open to ground
Rear Liftgate should read approximately 4
ohms across speakers and open to ground
Speaker Resistance
Measurements
Chasis ground
Right
1.5"
4 Ohm
Notes:
Speakers should be disconnected from the
main amplifier before the measurement is
made.
3.25"
4 Ohm