Pitts S2B

Pitts S2B
Instructions
Read these instructions carefully before use and retain them for future reference.
!
Safety Instructions
This model is not a toy!
Not suitable for under 14 year olds!
* Beginners should seek the help of an experienced modeler
to ensure the safe operation of the model
* Assemble the model away from small children
* Observe all of the safety instructions when assembling
the model. You are responsible for its safe operation
* Keep these instruction for reference even after you have
completed the model
GB
Item. No.
00 6130
Contents
Safety Information
General Information
Technical Details
Kit Contents
Building the model
Control Throws and Centre of Gravity
Recommended Accessories
Plan
2
2
2
3
3-14
14
15
16-19
Safety Information
Flying models are not toys, and should only be operated by responsible clear thinking people. Assembling and maintaining models
requires a basic level of technical skill, and a sensible logical approach. Any error in building, repairing or maintaining the model
could result in serious injury or damage. Technical problems or an
incorrectly assembled model may lead to the propeller unexpectedly beginning to turn. Always stay out of the vicinity of rotating
propellers and never allow any item to come into contact with a
spinning prop. As neither the manufacturer or the dealer has any
influence over the way that models are operated they can accept
no responsibility for and damage caused.
If this model is the first radio controlled model which you are attempting to build or fly, you should secure the assistance of an
experienced model pilot. Your local dealer will be able to assist
you in locating your local model aircraft club or experienced pilots
in your area.
NEVER fly your model over people and never operate the model
in way which may endanger people or animals. Before your first
flight you should conduct a range check of the radio control system, secure the model to a solid object, and ensure that you have
full control of all functions with the antennae collapsed over a distance of at least 25 metres. Before and after every flight inspect
the model for damage, and rectify any faults before you attempt to
take off. The operator is responsible for any damage caused by the
operation of flying models.
Always observe any local laws regarding the operation of model
aircraft.
Furthermore, the following instructions must be followed:
•
•
•
•
•
•
•
•
•
•
•
•
The kit contains small parts which may cause choking if swallowed keep away from small children.
The model should not be changed in any way, doing so will
invalidate the guarantee.
Never come into contact with rotating parts.
Do not fly over wet ground or grass as water will damage the
models electrical components
Do not expose the model or batteries to direct sunlight, always
keep them in the shade.
Inspect the model before and after every flight for damage.
Only ever fly the model if it is in perfect working order.
The model can only be flown in good weather. Do not fly in
wind, rain or thunder storms.
Find a place to fly which complies with any laws, and is free
from obstacles such as trees, houses or power cables.
Remember that your model is made from such materials as
plastic and wood, and as such is inflammable. Keep it away
from any open flame, or high temperatures.
When operating the model, switch on the transmitter first and
then the aircraft, switch off in the reverse order.
Always ensure that the throttle stick is in the low position before you switch on.
General Instructions
As the company JAMARA Modelltechnik has no influence over the
use, maintenance or conditions under which our products will operate, we accept no responsibility for any damage caused be it of a
physical, financial or theoretical nature.
JAMARA Modelltechnik will accept no claim against it which results
directly or indirectly from the operation or use of its products.
Warning!
In some countries it is a legal requirement to carry third party indemnity insurance when operating a radio controlled model.
Please ask your local dealer, governing body or your insurance company for details.
Warning!
Always switch on the transmitter first, and then the model.
Switch off the model first, and then the transmitter.
Technical Details
Wingspan
Length
Weight
R/C
Motor
2
approx. 800 mm
approx. 750 mm
approx. 720 g ( Ready to Fly )
4 Channel / 4 Servos
Electric Motor
Kit Contents
•
•
•
•
CNC Laser cut formers and ribs, strip, die-cut selected balsa
and light ply sheet.
Fitting kit including wheels, undercarriage, horns, hinges etc.
Clear canopy.
Instructions.
Building the Model
1. Glue the formers, undercarriage mount and strengthening
struts shown above securely.
2. Mount the battery plate, the wing supports and the blind nuts to the assembly as shown above. Ensure that all of the joints are sound.
3. The completed fuselage cell.
4.
Glue the blind nuts into the wing mounting plate and then glue the sub-assembly to the former ensuring that it is
vertical and square.
3
Building the Model
5. Glue the rear servo mounting plates and former together.
6. Securely glue the rear former to the wing plate/fuselage cell assembly.
7. The lower rear balsa fuselage plate can now be glued on fol
lowed by the servo mounting frame.
8. Glue a 3 mm stringer into the notches of the left and right
hand fuselage sides and glue them and the formers into
place.
9. The elevator seat is now fitted and a piece of 3 mm strip is
used to real the end.
10. Glue the front and rear 3 mm stringers into place leaving them over-hanging by approx 1 cm.
4
Building the Model
11.
Glue a 6 mm stringer to the lower left and right of the
fuselage sides and add the front former ensuring that it is
square and at right angles. 2 mm balsa should then be used
to plank the lower front fuselage.
12. Dampen 1.5 mm balsa sheet and plank the fuselage top at
the front and rear.
13. Glue the pins to the battery hatch.
14.
15. Completed upper wing half ready to be glued to the other
half.
16. Glue both wing halves together and fit the central leading
edge. Plank the upper and lower joint with the precut pieces and then fit the rear bridging piece.
Select all of the upper wing components and print out the
plan. Please note that the main spars are laser cut parts which
are not shown above. The longer main spar is for the upper
wing.
5
Building the Model
17. Glue the wing tip parts together and glue the completed
assemblies to the wing.
18. Glue a piece of scrap balsa to the rib where the inter-plane
struts are attached to allow the covering foil to be later ironed on.
19. Build the upper aileron from 2 X 6 mm balsa and sand to shape.
20. Sheet the front third of the wing and sand the sheeting and sand the leading edge joint smooth.
21. Lower wing joiner components.
22. Lower wing joiner components glued together.
6
Building the Model
23. Build the lower wing using the components shown above.
24. One half of the lower wing completed, the other half is a
mirror image.
25. Glue the servo frames to the lower wing as shown.
26. Fit the central sheeting and the rear strengthener.
27. Sand the strengthener to shape and add the upper central sheeting followed by the upper and lower main sheeting.
28. Build the ailerons from 2 X 6 mm balsa and sand to shape.
7
Building the Model
29. Assemble the tail surfaces as shown and sand the edges round.
30. Fit the cowl and sand it to shape.
Control Throws & C of G
Recommended Accessories
Elevator: +/- 15mm
BL Out-runner 36x30mm with approx.1100RPM
Rudder: +/- 30mm
BL ESC 30
Aileron: +/- 12-15mm
Propeller 10x5
C of G: 5mm IN FRONT of the lower wing LE
8
LiPo Battery Pack 3C 2200mAh
Accessories
Or
Motor A2212/10-BI
Item Nr. 13 2210
Motor A2217/8-BI
Item Nr. 13 2217
ESC Xetronic 25A
Item Nr. 08 1925
4 x Servos
High End Micro
Item Nr. 03 3212
Or
Battery Pack LiPo Star 11,1 V 1800 mAh
Item Nr. 14 1774
Battery Pack LiPo Star 11,1 V 2200 mAh
Item Nr. 14 1776
Propeller APC Electric 9 x 6
Item Nr. 34 0058
9
Plan - The original sized plan can be found on the DVD
Upper Wing
10
Plan - The original sized plan can be found on the DVD
Lower Wing
11
Plan - The original sized plan can be found on the DVD
Fuselage
12
Bauzeichnung - Die Originalgrösse finden Sie auf der beiliegenden DVD
Rumpf
13
Plan - The original sized plan can be found on the DVD
14
Notice
15
Irrtum und technische Änderungen vorbehalten.
Copyright JAMARA e.K. 2009
Kopie und Nachdruck, auch auszugsweise,
nur mit Genehmigung von JAMARA e. K.
Gutschein - Coupon
Fordern Sie noch Heute den aktuellen Hauptkatalog mit unserem gesamten
Warensortiment an.
Order the current catalogue with our complete
assortment of modelling goods today.
Name/Name
_______________________________
Vorname/First name _______________________________
Straße/Street
_______________________________
Wohnort/City
_______________________________
Telefon/Phone
_______________________________
E-mail
_______________________________
Bitte senden Sie den Katalog für mich an folgenden Fachhändler:
Please send the catalogue to the following specialist dealer:
Ihr Fachhändler/Your dealer
__________________________________________________
__________________________________________________
__________________________________________________
__________________________________________________
Der Katalog wird mit der nächsten Bestellung des Händlers auf Ihren Namen mitgeliefert.
We will include a catalogue for your attention with the next order of the specialist
dealer.
Newsletter
Aktuelle Neuheiten erfahren Sie in unserem Newsletter. Sollten Sie daran Interesse haben, abbonieren Sie den Jamara Newsletter.
Ihre E-mail-Adresse
______________________________________________________
You can receive up-to-date news through our newsletter. If you are interested, plese
apply for the Jamara Newsletter.
Your E-mail-Address
______________________________________________________
JAMARA e.K.
Inh. Erich Natterer
Am Lauerbühl 5 - DE-88317 Aichstetten
Tel. +49 (0) 75 65/94 12-0 - Fax +49 (0) 75 65/94 12-23
[email protected]
www.jamara.de
All rights reserved.
Copyright JAMARA e.K. 2009
Copying or reproduction in whole or part,
only with the expressed permission of JAMARA e.K.