55in Cessna 182 RTF/PNP

55in Cessna 182 RTF/PNP
Instruction Manual
Wing Span: 55.5in (1410mm)
Length: 40.6in (1030mm)
Wing Area: 424sq in (27.35dm)
Flying Weight: 2.4lb (1080g)
Parts (PNP version)
Package contents:
1. Fuselage
2. Wing
3. Horizontal tail
4. Vertical tail
5. Cowling
6. Main landing gear
7. Wheel set
8. Wing strut
9. Wing strut screws
10. Wing screws
11. 900kv brushless motor
12. Hobbywing Skywalker 30A ESC
13. 9g x 4 servo
14. 11 x 4.7 prop
15. Spinner
16. Y harness
17. Foam glue
In RTF version, Flysky FS-T4B radio system, 2200mah 3s LiPO battery and LiPO
balance charger are also included.
2
Assembly
Step1. Apply the foam glue onto the wing root
and the fiberglass wing tube.
Step5. Install nose wheel to the fuselage.
Step2. Attach two wing panels together.
Step6. Install the wing onto the fuselage.
Step3. Attach the main wheels to the landing gear.
Step7. Install the wing strut onto the fuselage and
wing.
Step4. Insert and glue the landing gear into the
fuselage.
3
Step8. Cut a slot at the tail of the fuselage for the
horizontal tail.
Step12. With the elevator servo centered, connect
the pushrod to the control horn.
Step9. Insert and glue the horizontal tail onto the
fuselage.
Step13. Install the prop and spinner to the motor.
Step10. Glue the vertical tail onto the fuselage.
Step11. With the rudder servo centered, connect
the pushrod to the control horn.
4
5.
Radio system Setup
Move throttle stick upwards to go flying
For more ESC setup information, please refer to the
manual for Hobbywing Skywalker series.
Instruction below is for RTF version (Flysky FS-T4B radio
system)
Receiver Connections
Center of Gravity
The recommended CG is 60mm from the leading edge
of the wing.
Bind the receiver to the transmitter
1.
2.
3.
4.
5.
Insert the bind plug into the BATT port on the
receiver.
Connect the receiver battery to any open port
except the Bind port. The LED light on the receiver
keeps flashing.
Press and hold the bind button on the transmitter,
then power on the transmitter
The LED light turns to solid.
The binding is completed.
Set the control throw
Elevator
Up 8mm
Linear measurement measured at widest part of
elevator (roughly in the center).
Throttle range setting
1.
2.
3.
4.
5.
Switch on the transmitter, move the throttle stick
to the top position.
Connect battery pack to the ESC, and wait for
about 2 seconds
The “beep beep” tone should be emitted, that
means the top point of throttle range has been
confirmed
Move throttle stick to the bottom position, several
“beep-”tone should be emitted to present the
amount of the battery cells.
A long “beep-” tone should be emitted, that means
the lowest point of throttle range has been
correctly confirmed.
Aileron
Up 8mm
2.
3.
4.
Down 8mm
Linear measurement (inches) measured at root.
Rudder
Left 8mm
Right 8mm
Linear measurement (inches) measured at front of
counterbalance.
Normal startup procedure
1.
Down 8mm
Move throttle stick to bottom position and then
switch on transmitter
Connect battery pack to ESC. Special tone like
“123” means power supply is ok
Several “beep-” tones should be emitted to
present the amount of LiPO battery cells
When self-test is finished, a long “beep---” tone
should be emitted
5