why aN EXtENDED PIN BOX

Comments

Transcription

why aN EXtENDED PIN BOX
why an extenDed pin box
Trucks come in many different configurations. Cequent Performance Products’ hitches are designed for use in light trucks
such as the Ford F-Series, the Chevy Silverado and the Dodge Ram. Cequent Performance Products recommends the use
of long bed (8ft) light trucks for the best combination in truck -trailer turning clearance.
Y
RV TRAILER
Rule of thumb:
The distance from the back of the truck cab
to the center of the rear truck axle “X”, should
be approximately 4 inches greater than onehalf the trailer width “Y”.
KING PIN
TRUCK
X
If a short bed pickup (less than 8 ft. but longer than 6 ft.) is to be used for towing, Cequent Performance Products recommends the trailer be equipped with a minimum 13” extended pin box to help gain additional truck -trailer turning clearance
(See trailer manufacturer for options) (See below). It also may be helpful for the 18K version to add an Elite series Slider
(Part # 30070) for increased turning clearance for low speed, non-highway maneuvering.
CONVENTIONAL
PIN BOX
WARNING:
Do Not install this fifth wheel hitch on or
attempt to tow with a short bed pickup truck
that has a bed shorter than 6 ft. Unless you
use a REESE Sidewinder or Revolution Pin
Box. Doing so could result in vehicle
damage, Serious injury, or Death.
EXTENDED
PIN BOX
The height of the hitch and the pin box should be adjusted so the trailer is approximately level as it is towed. Allow
approximately 6 inches clearance between the top of the pickup walls and the underside of the front of the trailer for
pitch and roll of the trailer. (See below.) For off road use allow more clearance between pickup walls and trailer.
APPROXIMATEDLY 6 INCHES
LEVEL TRAILER
CAUTION:
The measurements above are guidelines. If
your measurements are close to those numbers re-check clearances.If vehicle and/or
trailer has any added bed vicinity accessories
(i.e.fairings, airdams, groundeffects, bedrails,
etc.), additional dimensioning and clearance
checks have to be made.
PIN BOX DIMENSIONS
PIN BOXES
Pin Box
Width
134
Horizontal Distance
Center Distance
Horizontal
Distance
Bolt Size
Vertical
Distance
Vertical
Distance
Horizontal
Distance
Bolt Size
Vertical
Distance
Bolt
Size
Front Row
To KP
Rear Row
To KP
Front Row
To KP
Rear Row To KP
Front Row
To KP
Back Row To KP
PIN BOXES
PIN BOX CONVERSION
Pin Box Matrix Conversion . . . . . . . . . . . . . . . . . . . 136-137
PIN BOXES
Reese® Elite Airborne/Sidewinder™ . . . . . . . . . . . . . 138
Reese® Airborne/Sidewinder™ . . . . . . . . . . . . . . . . 139
Reese® Sidewinder™ . . . . . . . . . . . . . . . . . . . . . . . 140-141
PIN BOXES
Reese® 5th Airborne™ . . . . . . . . . . . . . . . . . . . . . . . 142
www.cequentgrou p . c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
135
PIN BOX MATRIX
Smoother ride, easier turning
Happier trails,
whatever path you take.
Whether you want to smooth out the rough
road’s impact on your trailer, hassle free
90-plus degree* turning, or both, Reese has
a fifth wheel pin box to meet your needs.
Rely on Reese’s innovative design and
superior performance to handle whatever
challenges you face down the road.
compare
5th Airborne™
21K
17.75"**
Varies by Model
22"
22"
22"
22"
GVW Capable
16K
21K
16K
19K
16K
19.5K
Air-ride
Yes
Yes
No
No
Yes
Yes
Anti-chucking Horizontal
60% Less
60% Less
No
No
60% Less
60% Less
Shock Control Vertical
44% Less
44% Less
No
No
44% Less
44% Less
Yes
Yes
Yes
Yes
Length
PIN BOXES
Short Bed Truck Capable
136
Elite Airborne Airborne /
Sidewinder™ Sidewinder™
/ Sidewinder™ Sidewinder™
16K
19K
16K
19.5K
5th Airborne™
16K
With Extended Pin Box With Extended Pin Box
and Sliding Hitch
and Sliding Hitch
Extra Space in Truck Bed
No
No
Yes
Yes
Yes
Yes
Reduces Need for Wide
Turns
No
No
Yes
Yes
Yes
Yes
Easier to Back Up
No
No
Yes
Yes
Yes
Yes
Included
Included
Yes
Yes
Included
Included
Convertible to Air-ride
*Not all tow vehicle and trailer combinations will allow 90-degree turn.
**Measurement is from the front bolts to the king pin.
www.cequentgroup .c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
PIN BOX MATRIX
Pin Box Matrix Conversion
5th Airborne™
16K
5th Airborne™
21K
Sidewinder™
16K
Sidewinder™
19K
Elite Airborne /
Sidewinder™
16K
Airborne /
Sidewinder™
19.5K
Complete
Part Number
Complete
Part Number
Complete
Part Number
Complete
Part Number
Complete
Part Number
Complete
Part Number
Fabex 520, 530, and 560
Lippert 1116 and 0115
RBW 7019
Not Available
5AB-S500-700
ST100-SW16K
ST100-SW19K
ST100-5AS16K
ST100-5AS02
Fabex 663
M&M 663
Lippert 0719
Not Available
5AB-S0719-600
ST200-SW16K
ST200-SW19K
ST200-5AS16K
ST200-5AS02
Venture CJ13515
Not Available
5AB-S13515
ST300-SW16K
ST300-SW19K
ST300-5AS16K
ST300-5AS02
Leland 7910
Not Available
5AB-S7910
ST400-SW16K
ST400-SW19K
ST400-5AS16K
ST400-5AS02
Youngs Welding
Not Available
5AB-800
ST500-SW16K
ST500-SW19K
ST500-5AS16K
Not Available
Fabex 500, 503 and 765
Lippert 1716
RBW 7028
Not Available
5AB-E510-710
ST100-SW16K
ST100-SW19K
ST100-5AS16K
ST100-5AS02
Fabex 665
M&M 665
Lippert 1621 HD
Not Available
5AB-E1621-610
ST200-SW16K
ST200-SW19K
ST200-5AS16K
ST200-5AS02
5AB-E1621-16K*
5AB-E1621-610
ST200-SW16K
ST200-SW19K
ST200-5AS16K
ST200-5AS02
Venture CJ13517
Not Available
5AB-E13517
ST300-SW16K
ST300-SW19K
ST300-5AS16K
ST300-5AS02
Leland 7920 and 7921
Not Available
5AB-E7920
ST400-SW16K
ST400-SW19K
ST400-5AS16K
ST400-5AS02
Youngs Welding
Not Available
5AB-E810
ST500-SW16K
ST500-SW19K
ST500-5AS16K
Not Available
Fabex 300, 314 and 316
Lippert 0516
RBW 7027
Atwood 2326
Not Available
5AB-T320
Not Available
Not Available
Not Available
Not Available
Atwood AB-34 and AB-72
Not Available
5AB-T7234
Not Available
Not Available
Not Available
Not Available
RBW 7016-2P
Not Available
5AB-T7016
Not Available
Not Available
Not Available
Not Available
Youngs Welding
Straight 8x8
Not Available
5AB-T820
Not Available
Not Available
Not Available
Not Available
OEM Part Numbers
S TA N D A R D
EXTENDED
Lippert 1621
TUBE
PIN BOXES
*Note: 5AB-E1621-16K will not fit the Lippert 1621 HD models, only the Lippert 1621
www.cequentgrou p . c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
137
ELITE AIRBORNE/SIDEWINDER™
ELITE Airborne/Sidewinder™ combo - The best of both worlds
Reese Elite Series pin boxes provide the smoothest ride of the best air-ride pin box
on the market and automatically eliminates turning and clearance headaches.
• Provides all the benefits of both the Reese 5th Airborne air-ride pin box and the
Reese Sidewinder pin box
• Enhances maneuverability and comfort
• Takes the worry and discomfort out of traveling with a fifth wheel trailer
• Durable, lasting design combines attractive look with optimal function
• 90-plus degree** turning with a short bed truck
• SAE/CSA rated 16K
**Warning: Not all vehicles and trailer combinations will allow a 90-plus degree turn.
Part No.
Description
5AS16K
ST100-5AS16K
ST200-5AS16K
ST400-5AS16K
Elite Airborne/Sidewinder™ Complete Arm Assembly
Elite Airborne/Sidewinder™ Combo
Elite Airborne/Sidewinder™ Combo
Elite Airborne/Sidewinder™ Combo
PIN BOXES
For pin box conversion see pin box matrix chart.
138
www.cequentgroup .c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
AIRBORNE/SIDEWINDER ™
Airborne/Sidewinder™ COMBO
The best of both worlds
Introducing the new Airborne / Sidewinder. The 5th Airborne combined with the
Sidewinder is the ultimate premium pin box. It provides all the benefits of both. The
5th Airborne provides the smoothest ride of all the air-ride pin boxes on the market
and easy automatic turning is offered by Sidewinder’s nimble and quick design. No
other hitch on the road takes the worry and discomfort out of your trailering experience. So sit back, relax and enjoy the smoothest ride on the road.
The Sidewinder system is designed for maximum flexibility and easy installation,
using existing holes and hardware.
If your fifth wheel isn’t already installed with a pin box from Reese, talk to your
dealer about which one is right for you. The only thing smoother and more worryfree than getting one installed is riding with one.
Part No.
Description
5AS02
ST100-5AS02
ST200-5AS02
ST300-5AS02
ST400-5AS02
Airborne/Sidewinder™ Complete Arm Assembly
Airborne/Sidewinder ™Combo
Airborne/Sidewinder™ Combo
Airborne/Sidewinder™ Combo
Airborne/Sidewinder™ Combo
For pin box conversion see pin box matrix chart.
turret
allows maximum
manuevering.
rear mounted shock absorber
heavy-duty shock absorber.
enclosed air bag
forward pivot
works in harmony
with your hitch pivot.
protected from UV
exposure and shielded
from road hazards.
universal king pin locking wedge
PIN BOXES
is reversible and adjustable.
www.cequentgrou p . c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
139
19K SIDEWINDER ™
19K Sidewinder™
Nimble and quick, worry-free turning
Sidewinder is the premium pin box designed specifically for short bed pickups. The
nimble and quick design automatically eliminates turning and clearance headaches.
Now you can make up to 90-degree plus* turns without exiting the truck. Without
throwing a switch. Without pushing a button.
Sidewinder’s king pin locking mechanism moves the pivot position 22” rear of the
pin box’s attachment point. This enables Sidewinder to handle up to a 90-degree
plus turn effortlessly. By moving the pivot rearward while keeping the load centered
over the axles, the trailer tracks more closely to the truck. This reduces the need
for extra-wide turns and allows short bed pickups to jackknife with no fear of contact. And it’s all done automatically. Sidewinder also offers faster steering wheel
response, making backing up easier than ever before. The pivoting pin box makes
hook up possible at any angle. And since the towing position of the arm of the pin
box is locked in line with the truck, you can make full use of the truck bed space,
giving you extra storage space for fuel tanks, toolboxes and cargo.
Don’t let the slim looks fool you. Sidewinder has been built for strength. The
C-channel design gives it more stability and strength than the standard pin box
design. It also allows better load capacity and the ability to support heavier loads.
Tested for real world conditions, Sidewinder has cleared rigorous testing by
BOSCH automotive proving grounds and exceeds all SAE/CSA Standard 19K ratings requirements for RVs.
Part No.
Description
ST100
ST100-SW19K
ST200
ST200-SW19K
ST300
ST300-SW19K
ST400
ST400-SW19K
ST500
ST500-SW19K
SW19K
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo -Turret w/Hardware + arm with king pin #ST100
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo -Turret w/Hardware + arm with king pin #ST200
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST300
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST400
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST500
Sidewinder™ Standard Arm
For pin box conversion see pin box matrix chart.
Nimble and quick.
Up to 90-degree plus turning.*
PIN BOXES
The Sidewinder moves the pivot from the truck bed to the pin
box mounting brackets under the nose of the trailer. In this way
you gain 22 inches of increased clearance instead of the typical
9 inches. It is now possible to jackknife the short bed truck
with no fear of contact. It is all done automatically.
140
More space above bed
walls for fuel tanks,
toolboxes and cargo.
Universal king pin locking
wedge is reversible and
adjustable to work with
all popular fifth-wheel
hitch brands.
*WARNING:
Not all tow vehicle and trailer combinations will allow a 90 degree turn
www.cequentgroup .c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
16K SIDEWINDER ™
16K Sidewinder™
Nimble and quick, worry-free turning
Sidewinder is the premium pin box designed specifically for short bed pickups. The
nimble and quick design automatically eliminates turning and clearance headaches.
Now you can make up to 90-degree plus* turns without exiting the truck. Without
throwing a switch. Without pushing a button.
Sidewinder’s king pin locking mechanism moves the pivot position 22” rear of the
pin box’s attachment point. This enables Sidewinder to handle up to a 90-degree
plus turn effortlessly. By moving the pivot rearward while keeping the load centered over the axles, the trailer tracks more closely to the truck. This reduces the
need for extra-wide turns and allows short bed pickups to jackknife with no fear
of contact. And it’s all done automatically. Sidewinder also offers faster steering
wheel response, making backing up easier than ever before. The pivoting pin box
makes hook up possible at any angle. And since the towing position of the arm of
the pin box is locked in line with the truck, you can make full use of the truck bed
space, giving you extra storage space for fuel tanks, toolboxes and cargo.
Don’t let the slim looks fool you. Sidewinder has been built for strength. The
C-channel design gives it more stability and strength than the standard pin box
design. It also allows better load capacity and the ability to support heavier loads.
Tested for real world conditions, Sidewinder has cleared rigorous testing by
BOSCH automotive proving grounds and exceeds all SAE/CSA Standard 16K
ratings requirements for RVs.
*WARNING:
Not all tow vehicle and trailer combinations will allow a 90 degree turn
Part No.
Description
ST100
ST100-SW16K
ST200
ST200-SW16K
ST300
ST300-SW16K
ST400
ST400-SW16K
ST500
ST500-SW16K
SW16K
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo -Turret w/Hardware + arm with king pin #ST100
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo -Turret w/Hardware + arm with king pin #ST200
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST300
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST400
Sidewinder™ Turret w/Hardware
Sidewinder™ Combo - Turret w/Hardware + arm with king pin #ST500
Sidewinder™ Standard Arm
For pin box conversion see pin box matrix chart.
custom wedges
SWW-03
www.cequentgrou p . c o m • Designed to work with the Sidewinder and Airborne / Sidewinder
• Replacement wedge that is designed for specific fifth wheel hitches
Part No.
SWW-01
30850
SWW-03
SWW-04
SWW-05
SWW-06
SWW-07
SWW-08
SWW-09
Description
Custom Wedge for Elite™ Series & Reese® 20K Fifth Wheels
Custom Wedge for Pro Series™ Fifth Wheels
Custom Wedge for Reese® 16K Fifth Wheels
Custom Wedge for Husky Fifth Wheels
Custom Wedge for Hi-Jacker Fifth Wheels
Custom Wedge for B&W Fifth Wheels
Custom Wedge for RBW Fifth Wheels
Custom Wedge for Colibert Fifth Wheels
Custom Wedge for PullRite Fifth Wheels
©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
PIN BOXES
30850
141
5th Airborne ™
5th Airborne™
Make your next getaway a breeze
The smoothest ride:
Your fifth wheel takes a lot of abuse from turbulence caused by potholes, section dividers, bridge decks and heavily worn interstate highways. The 5th Airborne
premium fifth wheel air-ride pin box acts as a buffer between the tow vehicle and
the trailer, minimizing the challenges in the road. This significantly reduces the
negative impact of vertical shock and longitudinal chucking. The 5th Airborne does
more than improve your ride; it protects your investments by relieving stress on
your coach’s frame, cabinets, mechanicals, and support mechanisms. Furniture,
appliances, TVs, computers, dishes, glassware and other fragile items stay in their
places. Drivers and passengers also benefit from reduced fatigue and the improved
safety provided by the 5th Airborne’s smooth ride.
Best on the market:
The 5th Airborne premium fifth wheel air-ride pin box was engineered and developed by long-time veterans of the towing industry.
Tests prove it’s the smoothest ride.
5th Airborne significantly outperforms
two leading competitors.
Longitudinal Shock Reduction (%)
0
10
20
30
40
50
60
59.9%
5th Airborne
Leading Antichucking
Competitor
23.0%
Vertical Shock Reduction (%)
0
10
20
Leading Air-ride
Competitor
40
50
60
22.3%
Part No.
Description
5AB-E13517
5AB-E1621-610
5AB-E510-710
5AB-E1621-16K
5th Airborne™ for Venture CJ13517 pin box
5th Airborne™ Extended 12” Wide Air Ride pin box
5th Airborne™ Extended 12-1/2” Wide Air Ride pin box
5th Airborne™ Extended 12” Wide Air Ride,
1-Piece Design - for Lippert 1621 only
5th Airborne™ for Leland 7920 pin box
5th Airborne™ for Youngs welding pin box
5th Airborne™ for Lippert 719 & Fabex 600 pin boxes
5th Airborne™ for Venture CJ13515 pin box
5th Airborne™ Standard 12-1/2” Wide Air Ride pin box
5th Airborne™ for Leland pin box
5th Airborne™ for Youngs welding pin box
5th Airborne™ Tube Style 8” Wide Air Ride pin box
5th Airborne™ for RBW 7016
5th Airborne™ Tube Style 12-1/2” Wide
5th Airborne™ Tube Style 8” Wide Air Ride pin box
5th Airborne™ Extended 12” Wide Air Ride pin box for 2007 Keystone Everest
with Sidewinder
5AB-E7920
5AB-E810
5AB-S0719-600
5AB-S13515
5AB-S500-700
5AB-S7910
5AB-S800
5AB-T320
5AB-T7016
5AB-T7234
5AB-T820
5AB-E510-710K
PIN BOXES
142
30
44.1%
5th Airborne
This product has been through grueling tests to measure its performance
against the top two competing premium pin boxes on the market. The
5th Airborne pin box, with its innovative forward pivot design, outperformed both leading competitors. Test measurements were recorded in
both the vertical (air-ride softening) direction and the longitudinal (antichucking) direction. The documented results proved that the 5th Airborne
performed significantly better in both orientations.
The streamlined, high-tech design of 5th Airborne adds a touch of class
to the otherwise mechanical-looking hitch. 5th Airborne is engineered
with a 21K CSA rating/SAE and 3 year warranty.
5th Airborne is designed to allow tuning of the air-spring, a feature that
permits adjustment to optimize the performance of each rig combination.
The air-spring is enclosed within the pin box, providing protection from
UV exposure and road hazards. The entire pin box is preassembled and
designed for easy installation using existing holes and hardware.
For pin box conversion see pin box matrix chart.
www.cequentgroup .c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
PIN BOXES
NOTES
www.cequentgrou p . c o m ©2010 Cequent Performance Products, Inc. P/N 98929-2011 Rev. A. 11/10 for 2011
143

Similar documents