Bubble Blowing Helicopter Manual
Transcription
Bubble Blowing Helicopter Manual
- Do not use the helicopter in direct sunlight or bright lighting, it will effect the infar-red signal. - Do not cover the aerial of the remote control as you will stop the signal to the helicopter. - Do not stick any lables on to the helicopter, as it could effect the signal to the helicopter from the remote control. - This product is made from light weight materials and if not operated correctly, it will damage the helicopter. 1. Only fly inside in calm air conditions. Away from air conditioners. 2. Fly in a space larger than 20ft(W) x 30ft (L) x 10ft(H) 3. Fly away from electric fans, airconditioners and other dangerous objects. 4. Don not fly near other people. Please read this manual before flying and retain for future reference SPARE PARTS SPARELIST PARTS LIST SPARE PARTS LIST Order parts from your local retailer or Flying Gadgets - [email protected] / 0208 952 0471 FG FLIGHT BUBBLE BLOWING HELICOPTER PARTS EXPLAINED Balance Bar Upper Blade Lower Blade Rear Blade Front Canopy Main Fuselage Bubble machine Bubble Container Landing Skid Bubble Switch Charging Socket Remote Control Direction Stick ON/OFF Switch Performance Button 1 INFRA-RED Channel Selector Power Control ON/OFF Switch Trimmer Switch BATTERY INSTALLATION & CHARGING BATTERY INSTALLATION Open the battery cover and insert 6 (AA) batteries. Make sure they are inserted with the correct polarity. Then replace the battery cover. FORWARDS To move FORWARDS, push the right hand direction stick FORWARD and the helicopter will move FORWARD.. BACKWARDS To move the helicopter BACKWARDS, move the left hand direction stick BACKWARDS and the helicopter will move BACKWARDS. CHARGING THE HELICOPTER BUBBLES Connect to a USB port Remote control charging: 1. Turn the remote control (ON), turn the helicopter power (OFF). 2. Take out the charging wire from the compartment in the remote control. 3. Connect the helicopter up to the remote control. 4. When the LED light on the front of the remote control turns from RED to GREEN charging is completed. USB Charging: 1. Plug the USB lead in to a computer or USB input. 2. Turn the helicopter (OFF) 3. Connect the lead to the helicopter. 4. When the RED light on the USB switches OFF, charging is completed. A FULL CHARGE TAKES UP TO 45 MINUTES AND WILL LAST FOR 6 MINUTES. To turn the bubbles ON, push the left hand button on the top of the controller and the helicopter will shoot bubbles out of the back of the helicopter. NOTE ON REFUELLING BUBBLES To fill the bubble tank, use the squeeze bottle and siringe end. Fill the squeeze bottle up with bubble fluid then squeeze in to the bubble tank access hole. TRIMMING THE HELICOPTER If the helicopter is moving to the left or the right without any control inputs. Then you will need to trim the helicopter. FLYING THE HELICOPTER - Set the Infra-Red channel selector on the remote control to the same as the helicopter. - Turn the remote control and then the helicopter (ON) - Place the helicopter on a flat surface. - Increase the power on the controller. - The lights will start flashing on the helicopter and then you can start flying! FLY UP AND DOWN To make the helicopter move UP push the left hand power stick up. To make the helicopter move DOWN move the left hand power stick towards you. Use only small movements for smooth flying. TURN LEFT/RIGHT To make the helicopter spin to the LEFT, move the right hand direction stick to the LEFT. To make the helicopter spin to the RIGHT, move the left hand direction stick to the LEFT. HELICOPTER SPINS TO THE RIGHT Press the L side of the trim button on the remote control. Continue pressing until it stops spinning to the right. HELICOPTER SPINS TO THE LEFT Press the R side of the trim button on the remote control. Continue pressing until it stops spinning to the left. BATTERY INSTALLATION & CHARGING BATTERY INSTALLATION Open the battery cover and insert 6 (AA) batteries. Make sure they are inserted with the correct polarity. Then replace the battery cover. FORWARDS To move FORWARDS, push the right hand direction stick FORWARD and the helicopter will move FORWARD.. BACKWARDS To move the helicopter BACKWARDS, move the left hand direction stick BACKWARDS and the helicopter will move BACKWARDS. CHARGING THE HELICOPTER BUBBLES Connect to a USB port Remote control charging: 1. Turn the remote control (ON), turn the helicopter power (OFF). 2. Take out the charging wire from the compartment in the remote control. 3. Connect the helicopter up to the remote control. 4. When the LED light on the front of the remote control turns from RED to GREEN charging is completed. USB Charging: 1. Plug the USB lead in to a computer or USB input. 2. Turn the helicopter (OFF) 3. Connect the lead to the helicopter. 4. When the RED light on the USB switches OFF, charging is completed. A FULL CHARGE TAKES UP TO 45 MINUTES AND WILL LAST FOR 6 MINUTES. To turn the bubbles ON, push the left hand button on the top of the controller and the helicopter will shoot bubbles out of the back of the helicopter. NOTE ON REFUELING BUBBLES To fill the bubble tank, use the squeeze bottle and siringe end. Fill the squeeze bottle up with bubble fluid then squeeze in to the bubble tank access hole. TRIMMING THE HELICOPTER If the helicopter is moving to the left or the right without any control inputs. Then you will need to trim the helicopter. FLYING THE HELICOPTER - Set the Infra-Red channel selector on the remote control to the same as the helicopter. - Turn the remote control and then the helicopter (ON) - Place the helicopter on a flat surface. - Increase the power on the controller. - The lights will start flashing on the helicopter and then you can start flying! FLY UP AND DOWN To make the helicopter move UP push the left hand power stick up. To make the helicopter move DOWN move the left hand power stick towards you. Use only small movements for smooth flying. TURN LEFT/RIGHT To make the helicopter spin to the LEFT, move the right hand direction stick to the LEFT. To make the helicopter spin to the RIGHT, move the left hand direction stick to the LEFT. HELICOPTER SPINS TO THE RIGHT Press the L side of the trim button on the remote control. Continue pressing until it stops spinning to the right. HELICOPTER SPINS TO THE LEFT Press the R side of the trim button on the remote control. Continue pressing until it stops spinning to the left. - Do not use the helicopter in direct sunlight or bright lighting, it will effect the infar-red signal. - Do not cover the aerial of the remote control as you will stop the signal to the helicopter. - Do not stick any lables on to the helicopter, as it could effect the signal to the helicopter from the remote control. - This product is made from light weight materials and if not operated correctly, it will damage the helicopter. Please read this manual before flying and retain for future reference 1. Only fly inside in calm air conditions. Away from air conditioners. 2. Fly in a space larger than 20ft(W) x 30ft (L) x 10ft(H) 3. Fly away from electric fans, airconditioners and other dangerous objects. 4. Don not fly near other people. SPARE PARTS LIST Order parts from your local retailer or Flying Gadgets - [email protected] / 0208 952 0471 FG FLIGHT BUBBLE BLOWING HELICOPTER PARTS EXPLAINED Balance Bar Upper Blade Lower Blade Rear Blade Front Canopy Main Fuselage Bubble machine Bubble Container Landing Skid Bubble Switch Charging Socket Remote Control Direction Stick ON/OFF Switch Performance Button 1 INFRA-RED Channel Selector Power Control ON/OFF Switch Trimmer Switch