IC-7000 Mods Página 1 de 8 KB2LJJ Radio Mods Database and

KB2LJJ Radio Mods Database and Manuals
Página 1 de 8
IC-7000 Mods
IC-7000 TV Enable Reception
IC-7000 Modifications
This information is for educational purposes ONLY This is a Reversible modification.
Do NOT use this modification if you are using this unit mobile. It is against the law in most jurisdictions to
have TV reception where the driver may see the screen.
DO use this as a BASE MODIFICATION ONLY.
TV Reception:
1. Remove the top cover of the unit. (There are only 8 screws holding the cover in place, do NOT remove the
four screws surrounding the speaker.)
2. Gently unplug the speaker wire and set the top to the side.
3. Gently lift the "Tuner Control Socket" and lift out of the way.
4. Remove DSP unit by unscrewing two silver screws holding it down. (The silver box on the top of the radio
under the cover, with copper taped sides) One of the screws was under the tuner socket control wires. Pull the
unit straight up.
5. Almost directly in the middle towards the front of where the DSP plugs is a Solder jumper. It is the ONLY
solder jumper on the board.
6. Remove that jumper with wick or sucker. (DO NOT REMOVE DIODES AS IN OTHER DIRECTIONS.)
7. Reassemble in reverse order.
8. With a new unit it enable reception automatically. (If you have already placed anything in memory
anywhere, do a CPU reset. BAND UP and BAND DOWN while turning the unit on.)
9. To make the TV work just hold the SET (AF control.) momentarily. Switch off the same manner.)
10. To change channels just rotate the tuning knob. The channels are built in memorized.
Copyright 2006
From the files of KB7ISR
IC-7000 (IC 7000 IC7000) TVRO & MARS (US version)
1. Remove CPU/DSP unit by unscrewing three silver screws holding it down (the silver box on the top of
the radio with copper taped sides) and pull up.
2. Locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to each
other and then a couple more. We'll call the two stacked the "left" ones
3. The "middle" shift register if looking from the front of the radio is the target.
4. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register.
They are in two columns, "left" and "right"
5. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip to
the side, whatever turns you on)
MARS:
OK - here's an out-of-band mod that does TX from 0-54, 118-173, 400-470.
1. Remove CPU/DSP unit by unscrewing three silver screws holding it down (the silver box on the top of
the radio with copper taped sides) and pull up.
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008
KB2LJJ Radio Mods Database and Manuals
Página 2 de 8
2. Locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to each
other and then a couple more. We'll call the two stacked the "left" ones.
3. The "left" shift register if looking from the front of the radio is the target.
4. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register.
They are in two columns, "left" and "right".
5. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip to
the side, whatever turns you on).
NOTE: The Automatic Repeater Shift on 2 meters and 440 is not affected by this mod! The “Band Edge
Beep”, on the other hand, does not function.
Copyright 2006
From the files of KB7ISR
TVRO & MARS/CAP Mods by N5AC
Fig. 1: IC-7000 CPU/DSP Unit and securing screws.
TVRO:
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008
KB2LJJ Radio Mods Database and Manuals
Página 3 de 8
1. Lift off the the top half of the radio case, after removing its securing screws.
2. Refer to Figure 1. Remove CPU/DSP unit by unscrewing two silver screws holding it down (the
silver box on the top of the radio with copper taped sides) and pulling the unit up. (The screws are
ringed in white.)
3. Locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to
each other and then a couple more. We'll call the two stacked the "left" ones.
4. The "middle" shift register if looking from the front of the radio is the target.
5. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register.
They are in two columns, "left" and "right".
6. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip
to the side, whatever you are comfortable with.)
Please observe local traffic laws concerning use of a TV set in a vehicle!
Fig. 2: Location of TVRO and MARS/CAP blocking diodes.
TVRO SETUP:
Please refer to the IC-7000 Instruction Manual, Pages 69 - 71.
Fig. 3: TV Channel Menu.
Fig. 4: Typical TV Image.
MARS/CAP:
Here is an out-of-band mod which allows transmitting from 0-54, 118-173 and 400-470
MHz. (Please observe radio regulations!)
1. Remove CPU/DSP unit by unscrewing two silver screws holding it down (the silver box on the top of
the radio with copper taped sides) and pull up. The screws are ringed in white (see Figure 1).
2. Locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to
each other and then a couple more. We'll call the two stacked the "left" ones.
3. The "left" shift register if looking from the front of the radio is the target.
4. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register.
They are in two columns, "left" and "right"
5. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip
to the side, whatever you are comfortable with.)
6. Note: After the modification has been performed, the "Band Edge Beep" feature will no longer
function, even if it has been enabled.
NOTE: The Automatic Repeater Shift on 2 meters and 440 is not affected by this mod
IC-7000 RX range expand mod
Loosen eight screws show in the photograph below. Pull them out and open the top cover
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008
KB2LJJ Radio Mods Database and Manuals
Página 4 de 8
Here is the main board. Take off two screws and pull up the silver box.
You have to remove two screws.
Detached silver box.
Take a closer look at the area shown below.
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008
KB2LJJ Radio Mods Database and Manuals
Página 5 de 8
Remove this diode.
Pack the stuffs back up.
IC-7000 Tone noise
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008
KB2LJJ Radio Mods Database and Manuals
http://www.kb2ljj.com/data/icom/ic-7000.htm
Página 6 de 8
02/05/2008
KB2LJJ Radio Mods Database and Manuals
http://www.kb2ljj.com/data/icom/ic-7000.htm
Página 7 de 8
02/05/2008
KB2LJJ Radio Mods Database and Manuals
Página 8 de 8
How to fix the IC-7000 audio noise
click on the link
IC7000_audio_noise.pdf
ATTENTION
The KB2LJJ takes no responsibility for any damage during the modification or for any wrong information
made on this modification.
http://www.kb2ljj.com/data/icom/ic-7000.htm
02/05/2008