Gas Spring Brochure

Transcription

Gas Spring Brochure
www.TCHWEB.com
[email protected]
1.800.465.6281
Choice and application of gas springs
Why use gas
springs?
Gas springs provide
a more uniform,
comfortable
adjustment or
pivoting movement
than mechanical
springs.
They can be used
for all applications:
trunk and gate
lifts, bus, truck
and aircraft
cargo, truck bed
covers, industrial
and agricultural
equipment, chairs,
hospital beds,
service panels,
windows and more.
Customization
of gas springs is
available if required
(minimum quantities
may apply).
Gas springs are
maintenance free!
Dimensions according
to choice
STABILUS
gas springs
STABILUS offers an extremely wide range of
gas spring types, which vary in respect of
their external dimensions, speed curves and
extension variants, and invariably meet the
most stringent requirements. A large selection is included in the STABILUS standard
product range and can be delivered at
short notice.
Service life and maintenance
Gas springs are maintenance-free! They are
designed to specific requirements and
operate for years and years without failure
when properly installed. Also for particularly high numbers of load alterations
special sealing systems are available which
allow e.g. specific gas springs in swivel
chairs to withstand up to one million load
cycles without damage.
Gas Springs
& Dampers
d
non-blocking
LIFT-O-MAT®
blocking
BLOC-O-LIFT®
Installation instructions
Twist-free connection
For maximum service life, gas springs
should not be exposed to twists or lateral
forces. Suitable connection fittings, e.g.
angle joints, can be used for the twist-free
connection of the gas springs.
STAB-O-MAT®
STAB-O-BLOC®
STAB
Temperature behaviour
The temperature of the gaseou
inside the gas spring influence
sion behaviour within certain l
standard temperature range lie
-30°C und +80°C. In addition
with special sealing systems fo
loads are available.
Installation position
Operational safety
Gas springs - except those designed for
The operational safety of the g
position-independent installation - are preprimarily achieved by seals des
ferably installed with the piston rod facing
keep the gas pressure inside. F
down so as to maximise the hydraulic
protection, no bending loads s
TCH
is an authorized distributor of
Stabilus
gasto springs;
we
carryexerted
the on the gas springs. Da
Connections
damping
effect and
ensure optimal
lubri®
non-blocking
line
gas depensprings LIFT‑O‑MAT
, the
gas springs
Different connections
areof
available
cation of the guide and
seal blocking
system.
by subsequent mechanical ope
® and
ding on the application.
STABILUS
therefore
including welding, performed
BLOC‑O‑LIFT
the line
of dampers, STAB‑O‑SHOC ®.
offers a wide range of plastic or metal
springs, as well as contaminat
hinge eyes, including the easy-to-mount
ting of the piston rod may lead
angle jointensures
that only has
to be
fitted on the
of the devices.
Stabilus
the
highest
quality of gas springs and fulfills thefailure
requireball socket and allows for twist-free instalments
of international standards, such as DIN EN ISO 9001 and new world
lation.
standard ISO/TS 16949.
End fittings
Different applications
require different connection
types; we have plastic and
metal hinge eyes, angle
joints and more, the shown
selection is only a small
amount of the selection
available.
Small selection of
available connections
Non-Blocking Gas Springs
Pressure tube
connection
D2
For lifting, lowering, moving and adjusting
Piston system
LIFT‑O‑MAT® gas springs offer optimum weight
compensation and force support!
Piston rod
Pressure tube
with filling medium
Oil
•Includes a wide range of sizes, forces and stroke lengths.
Special seal and
guide system
•Utilizes a linear spring curve for uniform force progression,
for opening and closing flaps and lids with user friendly
movement patterns.
•Offers applications either dynamic or hydraulic damping.
D1
•Has various connection options for practical and swift
installation.
Piston rod
connection
6 x 15 (D1 x D2)
8 x 18
10 x 22
Material: Steel | Finish: Black Nitrate or Stainless Steel
Material: Steel | Finish: Black Nitrate or Stainless Steel
Material: Steel | Finish: Black Nitrate or Stainless Steel
•Sizes available (stroke length / extended length):
•60 (2.36) / 195 (7.68) mm (in)
•80 (3.15) / 235 (9.25)
•100 (3.94) / 275 (10.83)
•120 (4.72) / 315 (12.40)
•150(5.91) / 375 (14.76)
•Sizes available (stroke length/extended length):
•80 (2.36) / 245 (9.66) mm (in)
•100 (3.94) / 285 (11.22)
•120 (4.72) / 325 (12.80)
•160 (6.30) / 405 (15.95)
•200 (7.87) / 485 (19.09)
•250 (9.84) / 585 (23.03)
•Sizes available (stroke length/extended length):
•200 (7.87) / 485 (19.09) mm (in)
•250 (9.84) / 585 (2.30)
•300 (11.81) / 685 (26.97)
•350 (13.78) / 785 (30.90)
•400 (15.75) / 885 (34.84)
Available in strengths from 50-400N (11-90 lbs)
Available in strengths from 100-600N (23-135 lbs)
Available in strengths from 150-1150N (34-258 lbs)
Typical Mounting Methods
HORIZONTAL DOOR
OFFSET DOOR
VERTICAL DOOR
Y+
Y+
YDOOR
OPE
YCEN
YFIXED
SITIO
N
YFIXED
N
YCEN
XFIXED
E
XFIXED
XCEN
CL
XDOOR
HINGE
POINT
(0,0)
YDOOR
ED
YHANDLE
X-
CLOSED POSITION
YDOOR
PO
SIT
IO
N
XFIXED
XCEN
XDOOR
XCEN
XHANDLE
XHANDLE
E
YCEN
YFIXED
OS
OPENNING
ANGLE
CLOSED POSITION
Y-
Y+
X+
YHANDLE
YHandle
TI
O
E
OPENNING
ANGLE
X-
N PO
OPENNING
ANGLE
SI
X+
ION
SIT
PO
PO
X-
EN
OP
HINGE
POINT
(0,0)
PE
N
XDOOR
O
HINGE
POINT
(0,0)
Y-
800.465.6281 • www.tchweb.com
Y-
XHANDLE
X+
Blocking Gas Springs
Pressure tube
connection according
to product range
Pressure tube
with filling medium
Separating
piston
D2
For variable positioning, rigid or spring
blocking.
Speed and damping
regulating valve system
BLOC‑O‑LIFT® gas springs raise and
lower accurately and hold in position
when stopped.
Special seal and
guide system
D1
Piston rod
connection with
thread
Spring Blocking
Gas Spring
•Can be blocked in any position by two different
methods rigid in extension or rigid in compression.
Rigid Blocking
Gas Spring with
separating piston
• Resilient blocking is ideal for smooth dampening of
shocks, impacts or pulse-peak loads.
•May be suitable for continuous release applications,
if required.
Blocking Gas Springs
Available in strengths from 200-1200N (45-270 lbs)
Material: Steel | Finish: Black Nitrate or Stainless Steel
•Sizes available (stroke length / extended length):
•60 (2.35) / 228 (8.98) mm (in)
•160 (6.30) / 430 (16.93)
•80 (3.15) / 269 (10.59)
•200 (7.87) / 509 (20.04)
•100 (3.94) / 310 (12.20)
•250 (9.84) / 610 (24.02)
•120 (4.72) / 348 (13.70)
*Spring blocking dimensions shown; rigid blocking gas springs are also available
Dampers
Hydraulic dampening of vibrations
and motions.
•Designed to match the application.
•Dampens forces in one or both extension and
compression direction.
•Variable damping rates.
800.465.6281 • www.tchweb.com
www.TCHWEB.com
[email protected]
1.800.465.6281
Mounting Brackets (other sizes and styles also available)
90 Degree Bracket with
10mm Ball Stud
Material: Steel | Color/Finish: Zinc plate |
Weight: 0.05 lbs
•1000 N maximum allowable force
(at 20°C in compressed position)
•Dimensions are in mm
Flat Bracket with
10mm Ball Stud
Material: Steel | Color/Finish: Zinc plate |
Weight: 0.05 lbs
•1000 N maximum allowable force
(at 20°C in compressed position)
•Dimensions are in mm
Mounting Bracket with 8mm Dia. Pin
Material: Steel | Color/Finish: Zinc plate |
Weight: 0.05 lbs
•1600 N maximum allowable force
(at 20°C in compressed position)
•Dimensions are in mm
While we show the most common gas springs and brackets, many more details and variations are
available through our Sales Representatives. Please feel free to contact us for assistance.
Buffalo
Calgary
Dallas
1370 William Street, Suite 4
Buffalo, NY, 14206, U.S.A.
Calgary, Alberta
Canada
10552 King William Drive
Dallas, TX, 75520 U.S.A.
MontrÉal
Toronto
16757 Boul. Hymus
Kirkland, QC, H9H 3L4, Canada
40 Emblem court
Toronto, ON, M1S 1B1, Canada
Copyright 2012, TCH Sales Inc., Toronto, Ontario, Canada, All rights reserved.
Drawings and specifications are subject to change without notice.
R2 (09/12)