GORE-TEX TriGuard GASKET
Transcription
GORE-TEX TriGuard GASKET
GORE-TEX® TriGuard ® GASKET GASKET FOR FRAGILE FLANGES Sealing with Certainty TM Key Features • Made from 100% multi-directionally expanded PTFE • Highly conformable • Seals at low bolt load • Chemically inert & temperature resistant • High dimensional stability & creep resistance • High blowout resistance Key Benefits • Seals highly permeable & aggressive fluids • Protects weak & fragile flanges from cracking • Seals damaged or misaligned flanges Low Stress to Seal Technical Data GORE-TEX® TriGuard ® gaskets are used to seal fragile pipe flanges with low bolt load. Unlike other gaskets, they seal tight and stay tight, even with varying flange conditions. Material: Designed for low stress-to-seal services such as FRP and glass-lined flanges, GORE-TEX® TriGuard ® gaskets are ideal for high purity applications and highly aggressive fluids, including chlorine and monomers. GORE-TEX® TriGuard® gaskets combine all the properties of expanded PTFE while providing reliable sealing of the most fragile flanges. ® Look to GORE-TEX TriGuard gaskets for superior performance in three important areas: conforming to irregular surfaces, helping to protect flanges, and seal reliability. With over 25 years of manufacturing and technical experience, depend on GORE-TEX® gasketing when you need the highest level of confidence. ® 100% expanded PTFE, with multidirectional strength. Temperature Range: –450°F to 600°F (-268°C to 315°C) Chemical Resistance: Resistant to all media in pH 0-14 range, except molten alkali metals and elemental fluorine, particularly at elevated temperatures and pressures. Operating Pressure: Vacuum to 1000 psig (68 bar) (HOBT2 @ 600°F (315°C)) Stability: Not subject to aging and can be stored indefinitely. Safety: Complies to FDA 21 CFR 177.1550 (PTFE) requirements for food • Seldom needs retorquing • Superior sealing reliability and long gasket life • Lowers total sealing cost GORE-TEX® TriGuard ® GASKET Sealing with CertaintyTM Compressibility Resistance to diffusion ASTM F-36 55% Sealability ASTM F-37 ("Y" value) 1500 psi ASTM F-586 ("m" factor) 2.4 GORE-TEX® TriGuard® gaskets have the lowest Y value of any PTFE-based gasket. What is important to users is that less torque on bolts means less chance of cracking fragile flanges. With a lower Y value, GORE-TEX® TriGuard® gaskets provide a tighter seal at lower bolt loads than other ePTFE and PTFE gaskets. Y-VALUE (PSI) 4000 Processors of aggressive chemicals must meet stringent requirements for leakage. They need to be confident that there is no start-up leakage. And they must maintain a tight seal to assure safety performance and minimize production loss. The bubble test, a commonly used measure of sealability in the fluid sealing industry, shows that GORE-TEX® TriGuard® gaskets seal at the low loads required in fragile flange applications. AIR PRESSURE Gasket Stress (psi) 30 psi (2 bar) 60 psi (4 bar) 90 psi (6 bar) 1500 NO LEAK NO LEAK NO LEAK 1000 NO LEAK NO LEAK NO LEAK 500 NO LEAK NO LEAK NO LEAK 250 NO LEAK NO LEAK NO LEAK GORE Bubble Testing: No observed leakage across a stress range of 250 psi to 1500 psi, with air pressures 30 to 90 psi. 3000 2000 Availability 1000 0 GORE-TEX® TRIGUARD® Gasket OTHER PTFEs Test Results: ASTM F-37 Sealability Testing (Y-Value @ 30 psi internal pressure, 1/8 in. thickness.) Installation Tighten to the manufacturer’s recommended torque load for the piping system. 1/2 inch through 24 inch ANSI ring and full face gasket sizes available. Thickness of 1/16", 1/8" and 1/4". Special sizes available on request. Contact us for more information Detailed selection criteria, technical assistance and installation guidelines are available from your local authorized Gore distributor or the application engineers at W. L. Gore & Associates, Inc. (800-654-4229). Visit us at www.gore.com. Authorized Distributor USA/Canada / Far East / Australia / Latin America / S. America W. L. Gore & Associates, Inc. 201 Airport Road, PO Box 1488 Elkton, MD 21922-1488 USA Tel: 410-392-3200 Fax: 410-392-4817 Europe / Middle East / Africa W. L. Gore & Associates, GmbH Wernher-Von-Braun-Str. 18 D-85640 Putzbrunn GERMANY Tel: 49 (0) 89 46 12-0 Fax: 49 (0) 89 46 12-2300 GORE-TEX, GORE, TRIGUARD, Sealing with Certainty and designs are trademarks of W. L. Gore & Associates. © 2003 W. L. Gore & Associates, Inc. IP ST 001 01/04