Sven Champion 7043

Weatherproof Tournament Table Tennis Table
SVEN® Champion
Owner’s Manual Model Number 7043-190
Printed on 100% recycled paper!
oof
r
p
r
e
h
Weat
y
l
e
t
u
Absol
Made in Germany
Thank you for purchasing our high quality KETTLER product.
If you have any questions or concerns regarding this product, please contact us:
KETTLER International, Inc.
Parts & Service Department
P.O.Box 2747
Virginia Beach, Virginia 23450 USA
E-mail [email protected]
Tel: 757-427-2400 ext. 26
Fax: 757-563-9273
Please have this owner’s manual with you when you call.
DO NOT CONTACT YOUR RETAILER.
Assembly Instructions
Before assembling or using the table-tennis table, please read the following instructions carefully. They contain important information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions
in a safe place for maintenance purposes or for ordering spare parts.
All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control
during manufacturing. The knowledge in this process is used to constantly improve and develop our products. In order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. Should you have any cause for complaint, please contact KETTLER at:
KETTLER International, Inc.
P.O.Box 2747
Virginia Beach, Virginia 23450 USA
Tel: 757-427-2400 ext. 26
Fax: 757-563-9273
E-mail [email protected]
Note on Safety
■ The table tennis table should be used only for its intended pur-
pose, i.e. for playing with suitable table tennis paddles and balls.
■ All other uses are prohibited and may be dangerous. The manufacturer cannot be held liable for damage or injury caused by
improper use of the table.
■ Damaged or worn components may endanger your safety or
shorten the lifespan of the table tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufactured by KETTLER.
■ The table tennis table complies with all safety regulations. Incorrect repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the
safety of the user.
■ Instruct other persons (in particularly children) using the table in
its correct use, and draw their attention to any potential source
of danger, especially folding or closing the table.
■ When setting up or dismantling the table, stay clear of its folding radius.
■ When folded up, the table tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a sheltered position.
■ The unit complies with the standard DIN 7898-1/10.97.
■ Depending on frequency of use, check all screws, bolts etc.
regularly to ensure that they are in good condition.
Handling the equipment
■ Do not use the table tennis table until it has been fully and cor-
rectly assembled and checked.
■ Set the table up on a level surface.
■ For practising without a partner, the table halves can be folded up singly.
■ Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the environment. In most cases, a slightly dampened cloth is sufficient.
Limited One-Year Warranty (Residential use)
Manufacturer warrants to the original retail purchaser, this
product to be free from defects in material and workmanship for
a period of one (1) year from the date of purchase. Should this
product become defective due to material or workmanship within
the warranty period, contact our Customer Service Department
for repair or replacement at our opinion. This warranty is not
transferable and does not cover normal wear and tear, bowing
of the table or damage caused by improper handling, installation
or use of this product. This warranty is also void if product is in
2
any way abused, damaged, or modified from its original state,
or if used for other than residential use. This warranty gives you
specific legal rights, and you may have other rights which vary
from state to state.
If table does not seem level, it is probably because floor is not level. Move table several inches (set table in playing position) in different directions to find the best location for the table. If the floor
is extremely unleveled, table may not play or operate properly. If
table is high in the center, shim up under the outer legs.
Instructions for Assembly
■ Carefully read these assembly instructions before beginning
with the work itself. The individual steps are additionally explained in the sequence by means of symbols, in some cases a
text mark indicates that a written explanation is available.
Strictly follow the individual mounting steps to ensure a safe use
and operation of the unit.
■ To ensure that the table-tennis table is properly assembled and can
be safely used, observe the instructions for assembly exactly.
■ Please note that there is always a danger of injury when working with tools or doing manual work. Therefore please be careful when assembling this machine.
■ Ensure that your working area is free of possible sources of
danger, for example don’t leave any tools lying around. Always dispose packaging material in such a way that it may not
cause any danger. There is always a risk of suffocation if children play with plastic bags!
■
■
■
■
The fastening material required for each assembly step is shown in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand until resistance is felt, then use spanner to finally tighten nuts completely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
For technical reasons, we reserve the right to carry out preliminary assembly work (e.g. addition of tubing plugs).
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Checklist (contents of packaging)
2x
2x
1x
2x
2x
4x
4x
1x
2x
2x
2x
2x
3x
4x M8x110
6x M8x45
6x M6x37
6x M6
16x ø12
8x
4x
4x M6x60
4x M8
4x M6
20x ø16
2x ø20
6x
4x M6x35
2x M8
2x
12x ø25
4x
4x
2x M8x120
1x
2x
You also need the following tools (Not included):
2x
SW13
SW10
2x
2x
2x
2x
1x
3
1
!
ACTU
AL S
IZE
4x
4x
4
4x
!
2
18,6cm
A
D
A
A
ø25
C
2x
ACTU
AL S
IZE
B
2x
B
ACTU
AL S
IZE
2x
C
ACTU
AL S
2x
2x
IZE
2x
8x
2x
5
3
C
ACTU
AL S
IZE
2x
4
2x
ACTU
AL S
IZE
2x
6
8x
2x
Ensure that it cannot slip or tilt over.
5
To do this, the braces for the frame
must be bent slightly to the side. Proceed with care when doing this.
2x
ACTU
AL S
IZE
4x
6
2x
ACTU
AL S
IZE
2x
4x
2x
7
7
A
B
B
A
ACTU
AL S
IZE
1x
1x
B
ACTU
2x
8
4x
1x
2x
2x
AL S
IZE
8
9
Carry out steps 5–8 for the second half of the table. Again, ensure that the table cannot slip or tilt over!
10
CLICK!
CLICK!
4x
9
1 Handling
Folding the table halves down:
press the left-hand tip lock. Hold the table firmly with one hand, press the
right-hand lock and lower the table-half
slowly into position. Never allow it to
drop down!
C
A
B
2
Folding the table halves up:
press the locking lever up and lift the table half upwards. Continue to press the
lever during the first part of the upward
motion.
B
A
10
3
4
C
D
E
F
A Adjustment knob; pull knob off net post
and select desired thickness (i.e. 19mm)
B Slide the netposts between the table halves.
C Slide the tension pin through net
D Place pin in designated slots
E Tie tension string to plastic tension tab.
F Place tension string in slots over tension pin
and net post. Adjust net tension by adjusting plastic tension tab.
19mm Wood
22mm Aluminium
A
B
Spare parts list
Item
1
2
3
4
5
6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Description
Pieces
TT-Platte (BITTE UNBEDINGT ARTIKEL-NUMMER DES TT-TISCHES ANGEBEN!)
Fussbügel/-gestell mit Bodenschonern
Bodenschoner
Stützbügel (kpl. mit Rohrverbindern, Sicherungen und Bundschrauben M6x30mm)
Sicherungshebel 1
Sicherungshebel 2
Lagerböckchen
Schubstange mit Rohrverbinder
Schubstange (kpl. mit Sicherung, Bundschraube M6x30mm und Rohrverbindern)
Verbindungsstange
Grundbügel (714mm)
Radhalter
Grundbügel (890mm) mit Stopfen für VKT 25mm
Abweisstange
Seitenverkleidung
Räder-Satz (4 Stück) mit Radverbinder
Radverbinder
Handdruckplatte
Bundschraube M6x37mm (o.Abb.)
Rechteckmutter M6
Stopfen für VKT 25mm
6kant-Schraube M8x120mm (o.Abb.)
6kant-Schraube M8x110mm (o.Abb.)
Distanzrohr ø12x1,8x64mm
Spreizniet ø6x9,5
Schraubenbeutel
Netzhalter
Netz
Schläger-/Ballhalterung (o.Abb.)
Spannlasche
Klemme zu Schläger-/Ballhalterung (o.Abb.)
2
2
4
2
4
2
8
2
2
3
1
2
1
2
2
2
2
6
6
4
2
2
4
2
4
1
2
1
1
2
2
Part No.
for 7043-190
(weatherproof)
94130003
94110769
70130540
94110771
94110762
94110763
10128024
94110758
94110755
94110764
94110765
70130811
94110767
70130602
70130817
94180177
70130812
70130530
10201209
10301000
10100046
10206115
10206081
97201453
10418503
94180178
10128022
73301010
70130561
10128002
70130567
Ordering spare parts
When ordering spare parts, always state the full product number, spare-part number, the quantity required and the control number stamped on the back.
Example order: Product No. 7043-190 / spare-part no. 10100046 / 2 pieces / inspection no......
Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.) is required, this should be clearly stated
on the order by adding the words „with fastening material“.
For parts, please contact us at:
KETTLER International, Inc.
P.O.Box 2747
Virginia Beach, VA 23450-2747 USA
E-mail [email protected]
Tel: 757-427-2400 ext. 26
Fax: 757-563-9273
11
Spare parts drawing
10
1
2
21
11
5
10
12
3
4
6
21
17
14
5
23
13
20
27
19
In case of complaint, please state this control number.
31
32
16
18
33
24
28
30
19
docu 934a/10.02
15