VQZ100/200/300

Transcription

VQZ100/200/300
3 Port Solenoid Valve
Metal Seal/Rubber Seal
Body Ported
VQZ100/200/300
Variations
SY
Nl/min
Metal/Rubber
Configuration
Voltage
Electrical
entry
Light and surge
voltage suppressor
Manual
override
SYJ
VK
VZ
Grommet (G)
VQZ100
VT
(Poppet)
—
196.3
VT
L plug
connector (L)
3 Port
Body Ported
(A)
2
31
(R) (P)
VQZ200
N.C.
441.68 588.9
(A)
2
(Standard)
12V DC
24V DC
(Option)
100V AC
110V AC
L plug
connector (L)
M plug
connector (M)
31
(R) (P)
VQZ300
VP
Non-locking
push style
(Flush)
VG
VQ
M plug
connector (M)
VQZ
N.O.
(Except for VQZ100)
Indicator light and
surge voltage
suppressor
DIN
connector (Y)
DIN
connector (Y)
Locking style
(Slotted)
Except for
VQZ100
785.2 883.35
Except for
VQZ100
2.9-1
VQZ100/200/300 Body Ported
Precautions
Be sure to read before handling. Refer to p.0-33 to 0-36 for Safety Instructions and common precautions.
Warning
Manual Override
Connection and Electrical Circuit
Without an electric signal for the solenoid valve the
manual override is used for switching the main valve.
With light and surge voltage suppressor
Circuit for DC
Non-locking push style (Flush)
Push down on the manual
override button with a small
screwdriver until it stops.
Release the screwdriver and
the manual override will return.
Circuit for AC
A (–)
(+)
Light
A
SOL
C(+)
(–) Light
SOL
C
ZNR
Due to the use of non-polar light, the VQZ series has no polarity.
Refer to p.1.12-26 for the latching style.
Locking style (Slotted) VQZ200/300
Push down on the manual override
button with a small screwdriver until it
stops. While down, turn clockwise by
90° to lock it. Turn it counterclockwise
to release it.
Connection of Lead Wire (Not necessary if ordering pre-connected model.)
Crimping connection of lead wire and socket
Strip 3.2 to 3.7mm of the lead wire ends, insert each stripped wire into a
socket and crimp it using the special crimping tool. Be careful that the
outer insulation of the lead wires does not interfere with the socket contact
part.
Core wire
contact area
Locking style(Slotted) VQZ100
Socket
Turn the manual override clockwise by
180° to set the mark to "1" and press
it in the direction indicated by arrow,
then it will be locked in the ON state.
Turn the manual override
counterclockwise by 180° to set the mark to "0", then it will be reset.
Caution
How to Use L and M Plug Connector
Connection/Disconnection of connector
Connection :
Push the connector straight onto
the pins of solenoid, making sure the
lip of the lever securely "locks" into
the groove of the solenoid cover.
M plug connector
Cover
Pin
Groove
Lead wire
0.2 to 0.33mm2
(Max.O.D. ø1.7mm)
Pin
Lever
Groove
2.9-2
Hook
Socket
Refer to p.2.9-19 for part No. of plug
connector assembly.
Lead wire
Insulation
Tool for crimping: Model No. DXT170-75-1
Connection/Disconnection of socket with lead wire
Connection
Insert lead wire and crimped socket into square holes (indicated as A,B,
COM) of connector. Press the socket in fully until the hook of the socket
locks into the groove of the connector housing. Confirm the locked
position by lightly pulling on the lead wire.
Disconnection
To remove the socket from the connector, pull out lead wire while
depressing the hook of the socket with a fine screwdriver. If
the socket is to be re-used, reposition the hook again.
Connector
Lead wire
Socket
Connector
Core wire
0.2 to 0.33mm2
Max.cover diameter
:ø1.7mm
Hook
Disconnection :
Press the lever against the connector
housing and pull it outward from the
solenoid.
L plug connector
Cover
Crimping area
Hook
VQZ100/200/300 Body Ported
How to Wire the DIN Connector
Changing One-touch Fittings
Conforming to ISO/DIN 43650 C (8mm between pins)
The built-in fittings on the manifold can be changed
easily. Simply remove the corresponding valve and
take out the fitting clip underneath. Then remove the
affected fitting and replace it with a new one. Finally,
replace the fitting clip and remount the valve.
Cut the power and air supply before mounting/removing the connector
qLoosen the top screw and remove the connector housing from the
terminal spades on the solenoid.
wRemove the housing screw and insert a screwdriver into the slot area
on the underside of the DIN cap and carefully separate block and housing.
eLoosen the treminal screws of the block and insert stripped lead wires
in accordance with the wiring diagram. Secure each wire by
retightening the terminal screw.
rTighten the housing grommet nut to secure the cable wire.
Clip
One-touch ass'y
Change of electrical entry (orientation)
Once the housing is separated from the terminal block, rotate it in any
direction to change the orientation of the electrical entry.
∗In the case of the indicator light option, avoid damaging the light with the
lead wire connections.
Pull connector out vertically, never at an angle.
: vertically clipped to
the valve body
VQZ200/300: horizontally clipped
to the valve body
Precaution
Applicable cable
Cord O.D.:ø3.5 to ø7
(Reference) 0.5mm2 2-core and 3-core wires equivalent to JISC3306.
SYJ
VQZ200
Precaution
When pulling the fitting ass’y away from the manifold base, remove the clip, then
connect a tube or plug (KQP-) with the One-touch fitting and pull it out while
holding the tube or plug. Do not hold the release bushing to avoid damage.
DIN Rail Removal/Mounting
Ground nut
(1.65~2.5N.m)
Fix screw
(0.3~0.4N.m)
Washer
Grommet
(Rubber)
Housing
(Voltage symbol)
Refer to below table
(Position for light mounting)
Terminal block
Terminal thread
(3 position)
(0.2~0.25N.m)
Shaved part
Part No. for DIN connector (Based on DIN)
K41
Without light
To remove manifold from DIN rail:
1) Loosen the clamp screw on the "A"
side of both ends of the manifold.
2) Lift the "A" side of the manifold off
the DIN rail and slide it in the
direction of the "B" side.
Mounting manifold to DIN rail:
1) Catch the hook of the DIN rail
bracket on the "B" side on the
DIN rail.
2) Push side "A" onto the DIN rail
and tighten the clamp screw.
(Tighening torque of 0.3 to 0.4
Nm)
Part No.
K42
K44
Fitting and Silencer Part Number for P,R Ports
When Using Valve as an Individual Unit
VQZ
After confirming the gasket is correctly placed under
the valve, tighten the mounting screws with the
appropriate torque listed below.
Suitable tightening torque
0.13 to 0.19Nm
0.25 to 0.35Nm
0.5 to 0.7Nm
One-touch fitting for 1(P) port
Screw
One-touch fitting
VT
VQ
Silencer for 3(R2,R), 5(R1)
Silencer One-touch fitting
KQH06-M5
AN120-M5 KJSO4-M5
VQZ100
KQH06-01S
INA-25-46 IN-457-32(for ø6)
VQZ200
KQH08-02S
AN101-01 KQH08-01S
VQZ300
The diameter of the above fitting and silencer is the maximum diameter for
proper installation.
Series
VT
A
Valve Mounting
Model
VQZ100
VQZ200
VQZ300
VZ
VG
B
Voltage symbol
24V
12V
100V
110V
VK
VP
With light
Rated voltage
24V DC
12V DC
100V AC
110V AC
SY
Clip
Silencer
2.9-3
3 Port Solenoid Valve
Body Ported
VQZ100/200/300
Plug Lead Unit
Valve Single Unit
How to Order Valve VQZ100
VQZ 1 1 5
5 M
C6
Q
PR
Series
Option
1
—
F
VQZ100 Body width 10mm
None
With bracket
Configuration
N.C.
(A)
2
1
Port size {2(A) port}
13
(P) (R)
C3
C4
C6
M5
N1
N3
N7
M5T
Body style
One-touch fitting for ø3.2
One-touch fitting for ø4
One-touch fitting for ø6
M5 thread
One-touch fitting for ø1/8
One-touch fitting for ø5/32
One-touch fitting for ø1/4
10-32 UNF thread
Manual override
—: Non-locking
push style
(Flush)
Function
Symbol
(1)
R
High pressure
Low wattage
Y
(2)
DC
(1.0W)
Standard
—
K
Specification
B: Locking style
(Slotted)
(1.0W)
(0.5W)
Electrical entry
External pilot
G: Grommet L: L plug
LO: L plug
M: M plug
MO: M plug
(DC
connector
terminal without connector
terminal without
specification) with lead wire connector
with lead wire connector
Note 1) Option
Note 2) When specifying more than
one option, indicate them
alphabetically.
With indicator light and
surge suppressor
With indicator light and With indicator light and With indicator light and
surge suppressor
surge suppressor
surge suppressor
Note) Standard lead wire length: 300mm
Coil voltage
5
6
9
Order
Made
Protective class
class III (Mark:
2.9-4
)
24V DC
12V DC
Other (50V or less)
Contact SMC
for other voltages (9)
VQZ100/200/300 Body Ported
How to Order Valve VQZ200/300
VQZ 2 1 2
5 M
C6
Q
Series
VQZ200 Body width15mm
VQZ300 Body width18mm
Bracket
Thread
Configuration
N
T
F
(A)
2
N.C.
N.O.
31
(R) (P)
(A)
2
Metal seal
1
Rc (PT)
NPT
NPTF
G (PF)
None
With bracket
—
F
Symbol
C4
C6
C8
C10
M5
02
N3
N7
N9
N11
M5T
31
(R) (P)
(A)
2
N.C.
3
N.O.
31
(R) (P)
(A)
2
4
31
(R) (P)
Body style
SY
SYJ
VK
VZ
Port size {2(A)port}
2
Rubber seal
2
3
Port size
VQZ200
One-touch fitting for ø4
One-touch fitting for ø6
—
One-touch fitting for ø8
—
One-touch fitting for ø10
M5 thread
—
1/4
One-touch fitting for ø5/32
One-touch fitting for ø1/4
—
One-touch fitting for ø5/16
—
One-touch fitting for ø3/8
10-32 UNF thread
VQZ300
—
VT
VT
—
VP
—
VG
—
Body ported
2
Manual override
Function
Symbol
—
K
(1)
Specification
DC
Standard
(1.0W)
High pressure
(Metal seal only)
(1.0W)
Y
Low wattage
R
External pilot
(0.5W)
AC
—: Non-locking B: Locking style
(Slotted)
push style
(Flush)
VQ
VQZ
—
—
Electrical entry
Note 1) Option
Note 2) When specifying more than one
option, indicate them alphabetically.
G: Grommet L: L plug
M: M plug
MO: M plug
LO: L plug
(DC
connecor
terminal without
terminal without connecor
Specification) with lead wire connector
with lead wire connector
With light and
surge voltage
suppressor.
With light and
surge voltage
suppressor.
With light and
surge voltage
suppressor.
With light and
surge voltage
suppressor.
Coil voltage
1∗
3∗
5
6
9
Order
Made
100V AC (50/60Hz)
110V AC (50/60Hz)
24V DC
12V DC
Others (DC50V or less)
Contact SMC
for other voltages (9)
Y: DIN
terminal
YO: DIN
YZ: DIN
terminal without terminal
connector
With light and
surge voltage
suppressor.
YOS: DIN
terminal without
connector
With surge
voltage
suppressor
∗ DIN type only available.
Protectiv e class
class I (Mar k:
) ......DIN terminal type
Protectiv e class
class III (Mar k:
Note) Standard lead wire length: 300mm
) ......Other
2.9-5
VQZ100/200/300 Body Ported
Standard Specifications
Seal
Metal seal
Max.operating pressure
Min.operating pressure
0.1MPa
–10 to 50 °C (1)
Valve
Ambient and fluid temp.
5Hz
Individual EXH
Pilot valve EXH
Not required
Lubrication
Non-locking push style/Locking slotted style
Manual override
150/30 m/s2
Shock/Vibration resistance (2)
Dust proof
Enclosure
12V, 24V DC and 100V, 110V AC
±10% of rated voltage
Coil rated voltage
Allowable voltage
Class B or equivalent
Coil insurance
Solenoid
0.7MPa
0.15MPa
–10 to 50 °C (1)
20Hz
Max.operating frequency
Power
consumption
(Current
value)
Rubber seal
Air, Inert gas
0.7MPa (High pressure style: 1.0MPa)
Fluid
1W DC (42mA), 0.5W DC (21mA)
24V DC
12V DC
1W DC (83mA), 0.5W DC (42mA)
100V AC
Inrush 0.5VA (5mA), Holding 0.5VA (5mA)
110V AC
Inrush 0.55VA (5mA), Holding 0.55VA (5mA)
Note 1) Use dry air to prevent condensation when operating at low temperatures.
Note 2) Shock resistance : No malfunctions resulted from the impact test using a drop impact tester. The
tests were performed on the axis and right angle direction of the main valve and
armature, for both energized and de-energized states. (Value in the initial stage.)
Vibration resistance: No malfunctions occurred in a one-sweep test between 8.3 and 2,000 Hz. Tests
were performed at both energized and de-energized states on the axis and right
angle direction of the main valve and armature. (Value in the initial stage.)
Model
(1)
Series
Valve configuration
Model
(Nl/min)
VQZ100
N.C.
N.C.
VQZ200
N.O.
N.C.
VQZ300
N.O.
Response time (ms) (2)
Effective area (mm2)
Standard: 1W
High pressure: 1W
Low wattage and AC
Poppett
VQZ115
3.6 (196.3)
10 or less
13 or less
Metal seal
VQZ212
8.1 (441.68)
14 or less
18 or less
Rubber seal
VQZ232
10.8 (588.6)
15 or less
20 or less
Metal seal
VQZ222
7.2 (392.6)
14 or less
18 or less
Rubber seal
VQZ242
10.8 (588.9)
15 or less
20 or less
Metal seal
VQZ312
14.4 (785.2)
17 or less
22 or less
Rubber seal
VQZ332
16.2 (883.35)
25 or less
33 or less
Metal seal
VQZ322
13.5 (736.13)
17 or less
22 or less
Rubber seal
VQZ342
16.2 (883.35)
25 or less
33 or less
Note 1) Value for sub-plate and maximum diameter
Note 2) As per JISB8375-1981 (Supply pressure; 0.5MPa; with indicator light and surge voltage suppressor; clean air)
The response time is subject to the pressure and the air quality. The values at the time of ON are given for the double styles.
Note 3) Weight without sub-plate
2.9-6
(3)
Weight(g)
25
58
92
VQZ100/200/300 Body Ported
Construction
VQZ100
Poppet
wq
e
Component Parts
N.C.
No.
(A)
2
q
Body
Resin
w
Spool valve
Aluminium/NBR
e
Pilot valve
r
P, R plate
—
Resin/Aluminium VQZ100-12A
13
(P) (R)
r
Description
Material
Notes
SY
SYJ
VK
VZ
VT
VQZ200/300
Metal seal
VT
Rubber seal
VP
r
w
e
q
r
e
w
q
VG
VQ
N.C.
r
(A)
2
(A)
2
31
(R) (P)
31
(R) (P)
q
w
e
VQZ
N.C.
r
N.O.
e
w
q
N.O.
(A)
2
(A)
2
31
(R) (P)
31
(R) (P)
Component Parts
No.
q
Description
Material
Notes
Body
Aluminium die cast
Spool/Sleeve
Stainless steel
Metal seal
Spool valve
Aluminium/NBR
Rubber seal
e
Piston
Resin
r
Pilot valve
w
—
2.9-7
VQZ100/200/300 Body Ported
Dimensions: VQZ100
Valve single unit
Grommet (G): VQZ115-G-C3, C4, C6, M5-PR-Q
M5
P port
M5
R port
9
(53)
3
1.2
13.8
≅7.8(C3, C4, C6)
(M5: 5.7)
Cover dia ø1.6
Cross section 0.34mm2
(≅7.8)
(24.5)
6
7
10
10
24.5
18
16.3
13.6
2-ø3.4 Mounting holes
(2)
Foot bracket
27.5
≅300
R
1
10.7
32
(Only external pilot style (R))
(Lead wire)
P
M5 X 0.8 External pilot port
41
2-C3, C4, C6, M5
C3: One-touch fittings for ø3.2
C4: One-touch fittings for ø4
C6: One-touch fittings for ø6
M5: M5 thread
16
4.3
2-ø3.2
Mounting holes
53
13.8
10
A
2
Manual override
≅300
M plug connector (M): VQZ115-M-C3, C4, C6, M5-PR-Q
60.5
≅300
(Lead wire)
34
Cover dia ø1.5
Cross section 0.23mm2
2.9-8
40.5
Indicator light
Indicator light
(Lead wire)
L plug connector (L): VQZ115-L-C3, C4, C6, M5-PR-Q
Cover dia ø1.5
Cross section 0.23mm2
55.5
VQZ100/200/300 Body Ported
VQZ200
Valve single unit
Grommet (G): VQZ22(R)-G-C4, C6, M5-Q
1/16
R port
1/8
P port
PE port
P
1
3
R
11
SY
14.5
SYJ
2.5
≅10
(C4, C6)
2-ø2.2 Die cast hole
For manifold gasket positioning
VZ
29.5
25
(M5)
20
2.1
30
4.5
12.5
9 9.2
2-M2.5
Thread length 4
≅10
2-ø3.5 Mounting holes
5.2
28
2-ø3.2 Mounting holes
2-C4, C6, M5
VT
VT
4.1
22.5
29.5
5
VK
VP
C4: One-touch fittings for ø4
27
34
C6: One-touch fittings for ø6
70
≅300
VG
M5: M5 thread
19.3
(Lead wire length)
.7
R2
Foot bracket
15
SMC
11
A
20.5
34
Manual override
M3 External pilot port
(Only external pilot style (R))
3.5
2
Cover dia ø1.6
Cross section 0.34mm2
8
VQ
VQZ
2-ø2.7 Mounting holes
L plug connector (L): VQZ22(R)-L-C4, C6, M5-Q
DIN terminal (Y): VQZ22(R)-Y-C4, C6, M5-Q
Indicator light
83
≅300
32
(Lead wire)
MAX.10
Cover diameter ø1.5
Cross section 0.23mm2
Applicable cord O.D.
87
Pg.7
Indicator light
≅300
Cover dia ø1.5
Cross section 0.23mm2
89
77
37.5
Indicator light
(Lead wire)
M plug connector (M): VQZ22(R)-M-C4, C6, M5-Q
36
61.5
54
ø3.5 to ø7
2.9-9
VQZ100/200/300 Body Ported
Dimensions: VQZ300
Valve single unit
Grommet (G): VQZ32(R)-G-C6, C8, C10, 02-Q
16.7 15.4
PE port
P 1
A
1.5
3 R
1/8
R port
1/4
P port
3
2.5
2-ø4.5 Mounting holes
4
C6, C8, C10, 02
38
46.5
C6: One-touch fittings for ø6
C8: One-touch fittings for ø8
≅300
75.5
60.5
41.8
(Lead wire)
C10: One-touch fittings for ø10
Foot bracket
02: 1/4
22
2-ø3.4 Mounting holes
18
4
SMC
13
A
R3
2
Cover dia ø1.6
Cross section 0.34mm2
Manual override
28.6
7.1
M5 External pilot port
(Only exterminal pilot style (R))
L plug connector (L): VQZ32(R)-L-C6, C8, C10, 02-Q
DIN terminal (Y): VQZ32(R)-Y-C6, C8, C10, 02-Q
88.5
≅300
(Lead wire)
31.5
Indicator light
MAX.10
Applicable cord O.D.
Cover dia ø1.5
Cross section 0.23mm2
37
2.9-10
(Lead wire)
≅300
Indicator light
Cover dia ø1.5
Cross section 0.23mm2
82.5
92.5
Pg.7
Indicator light
61
53.5
35.5
ø3.5 to ø7
M plug connector (M): VQZ32(R)-M-C6, C8, C10, 02-Q
≅10.5
20
28.5
36
47.5
38.5
(02)
31.5
13
16.5
9
2-ø3.4 Mounting holes
6.5
24.5
9
2-M2.5
Thread length 6
6.5
(C10)
≅17.5
≅10.5
(C6, C8)
2-ø3 Die cast hole
For manifold gasket positioning
94.5
3 Port Solenoid Valve
Body Ported
VQZ100/200/300
Plug Lead Unit
Manifold
Connector kit
How to Order Manifold VQZ100
VV3QZ 1 2
08 C
VK
Thread(P, R port)
00N
00T
00F
VQZ100
Manifold style
2
SYJ
Q
D
Series
1
SY
Rc (PT)
NPT
NPTF
G (PF)
VZ
VT
Option
Body ported
—
D
DO (1)
R (2)
Stations
02 2 stations
VT
None
DIN rail mounting (DIN rail standard length)
DIN rail mounting (Without DIN rail)
External pilot
VP
VG
Note 1) Order DIN rail separately.
20 20 stations
Protectiv e class
class III (Mar k:
Note 2) When specifying more than one option,
indicate them alphabetically.
Kit
)
C
Connector
VQ
How to Order Valve VQZ100
VQZ 1 1 5
5 M
C3
VQZ
Q
Port size {2(A) port}
C3
C4
C6
M5
Series
1
One-touch fitting for ø3.2
One-touch fitting for ø4
One-touch fitting for ø6
M5 thread (Changeable style)
Note)Refer to p.2.9-18 for inch-size
One-touch fittings.
VQZ100 Body width10mm
Manual override
—
B
Configuration
1
Non-locking push style (Flush)
Locking style (Slotted)
N.C.
Electric entry
Symbol
G
L
LO
M
MO
Body style
Function
Symbol
Specification
Standard
—
K
(1)
High pressure
Low wattage
Y
R (2)
DC
(1.0W)
(1.0W)
(0.5W)
AC
Electrical entry
Grommet (DC specification)
L plug connector with lead wire
L plug terminal without connector
M plug connector with lead wire
M plug terminal without connector
Light and surge
suppressor
Without
With
Note) Standard lead wire: 300mm
(3)
Coil voltage
—
—
External pilot
Note 1) Option
Note 2) Refer to p.2.9-18 for details about
external pilot specification.
Note 3) Refer to p.2.9-6 for power
consumption of AC type.
Note 4) When specifying more than one
option, indicate them alphabetically.
5
6
9
24V DC
12V DC
Others (50V or less)
Order
Made
Contact SMC
for other voltages (9)
2.9-11
VQZ100/200/300 Body Ported
How to Order Manifold VQZ200/300
VV3QZ 2 2
08 C
Q
D
Thread(P, R port)
Series
2
3
00N
00T
00F
VQZ200
VQZ300
Manifold style
2
Option
Body ported
—
D
DO ∗
Stations
Protectiv e class
class III (Mar k:
Rc (PT)
NPT
NPTF
G (PF)
None
DIN rail mounting (DIN rail standard length)
DIN rail mounting (Without DIN rail)
∗ Order DIN rail separately
02
2 stations
20
20 stations
Kit
Connector
C
)
How to Order Valve VQZ200/300
VQZ 2 1 2
Q
5 M
Thread(P, R port)
Series
2
3
N
T
F
VQZ200 Body width 15mm
VQZ300 Body width 18mm
Rc (PT)
NPT
NPTF
G (PF)
Port size {2(A) port}
Symbol
1
2
3
4
Symbol
C4
C6
C8
C10
M5
02
N.C. Metal seal
N.O. Metal seal
N.C. Rubber seal
N.O. Rubber seal
Port size
One-touch fitting for ø4
One-touch fitting for ø6
One-touch fitting for ø8
One-touch fitting for ø10
M5 thread
Rc(PT)1/4
VQZ200 VQZ300
—
—
—
—
—
Note 1) Refer to p.2.9-18 for Inch size One-touch fitting.
Body style
2
Manual override
Body ported
—
B
Non-locking push style (Flush)
Locking style (Slotted)
Electrical entry
Symbol
—
K
(1)
High pressure
(Metal seal only)
Low wattage
Y
R
Specification
Standard
(2)
Electrical entry
Symbol
Function
DC
(1.0W)
(1.0W)
(0.5W)
AC
G
L
LO
M
MO
Y
YO
YZ
YOS
(3)
—
—
External pilot
Note 1) Option
Note 2) Refer to p.2.9-18 for details about
external pilot specification.
Note 3) Refer to p.2.9-6 for power
consumption of AC type.
Note 4) When specifying more than one
option, indicate them alphabetically.
Grommet (DC specification)
L plug connector with lead wire
L plug terminal without connector
M plug connector with lead wire
M plug terminal without connector
DIN terminal
DIN terminal without connector
DIN terminal
DIN terminal without connector
Note) Standard lead wire length: 300mm
Coil voltage
1∗
3∗
5
6
9
Order
Made
100V AC (50/60Hz)
110V AC (50/60Hz)
24V DC
12V DC
Others (50V or less)
Contact SMC
for other voltages (9)
∗ DIN type only available.
2.9-12
Light and surge
suppressor
Without
With
Without
With
with (Without light)
VQZ100/200/300 Body Ported
Manifold Specifications
Piping specification
Series
Base model
VQZ100 VV3QZ12-
VQZ200 VV3QZ22-
VQZ300 VV3QZ32-
Piping
Port size
1(P), 3(R)
Top
Top
Top
2(A)
Manifold
Applicable Applicable base weight
(g)
valve
stations
1/8
C3 (for ø3.2)
C4 (for ø4)
VQZ115
C6 (for ø6)
M5 (M5 thread)
1/8
C4 (for ø4)
C6 (for ø6)
VQZ22
M5 (M5 thread)
1/4
C6 (for ø6)
C8 (for ø8)
C10 (for ø10)
Rc(PT)1/4
2 to 20
2 stations: 83
Addiitional
station: 19
2 to 20
2 stations: 68
Addiitional
station: 20
2 to 20
2 stations: 114
Addiitional
station: 37
SY
SYJ
VK
VQZ32
VZ
VT
VT
VP
VG
How to Order Manifold Assembly (Example)
e
sU
sid
n
tio
sta
VQ
5
4
3
VQZ
VQZ212-5M-C6 4 set
VV3QZ22-05C-Q
VVQZ200-10A-2
VQZ212-5M-C6-Q
2
1
ide
Ds
1 set (C kit 5 stations manifold base)
1 set (Blank plate assembly)
4 sets (N.C. style)
C6: One-touch fitting for ø6
VVQZ200-10A-2
VV3QZ22-05C
2.9-13
VQZ100/200/300 Body Ported
Dimensions: VQZ100
39.5
(M5)
Cover diameter ø1.6
Cross section 0.34mm2
42.5
Grommet (G)
≅7.8 (C3, C4, C6)
≅300
(Lead wire)
VV3QZ12- Station C-Q
(11)
8
13
2-1/8
R(EXH) port
16.3 13.4
2-M5
PE port
15
R
P
41.2
46.5
2-1/8
P(SUP) port
27
(35)
(5.5)
(11)
2-ø4.5 Mounting holes
(7.5)
20
n-C3, C4, C6, M5
C3: One-touch fittings for ø3.2
C4: One-touch fittings for ø4
C6: One-touch fittings for ø6
M5: M5 thread
(4.5)
5.5
DIN rail clamp screw
U side
n
Manual override
5
A
L1
L2
P=10.5
2 A
(L3)
3
2 A
(L4)
4
2
2 A
1
16.5
2
5.5
Stations
D side
2-M5 External pilot port
(Only external pilot style (R))
2.3
21.6
35
53
M plug connector (M)
66
≅300
≅300
(Lead wire)
Indicator light
Cover dia ø1.5
Cross section 0.23mm2
61 64.5
55.5
49
Cover dia ø1.5
Cross section 0.23mm2
Indicator light
(Lead wire)
L plug connector (L)
5.5
R
P
Dimensions
n
L
L1
L2
L3
L4
2.9-14
2
30.5
43.5
75
85.5
R
P
13
13
Equation L1=10.5n+9.5 L2=10.5n+22.5
3
41
54
75
85.5
4
51.5
64.5
87.5
98
5
62
75
100
110.5
6
72.5
85.5
112.5
123
7
83
96
125
135.5
8
93.5
106.5
137.5
148
n: Station (Max. 20)
9
104
117
137.5
148
10
114.5
127.5
150
160.5
11
125
138
162.5
173
12
135.5
148.5
175
185.5
13
146
159
187.5
198
14
156.5
169.5
200
210.5
15
167
180
200
210.5
16
177.5
190.5
212.5
223
17
188
201
225
235.5
18
198.5
211.5
237.5
248
19
209
222
250
260.5
20
219.5
232.5
262.5
273
VQZ100/200/300 Body Ported
Dimensions: VQZ200
Cover diameter ø1.6
Cross section 0.34mm2
R
3
7.5
(18)
48.5
Grommet (G)
P
1
43.5
(M5)
≅10
(C4, C6)
VV3QZ22- Station C-Q
(11)
SY
PE port
18.5
2-1/8
R(EXH) port
(7.5)
18
SYJ
34
VK
(35)
(5.5)
2-ø4.5 Mounting holes
(11)
26
7.8
2-1/8
P(SUP) port
DIN rail clamp screw
n-C4, C6, M5
C4: One-touch fittings for ø4
C6: One-touch fittings for ø6
M5: M5 thread
0.5
VZ
VT
U side
n
5
VT
Manual override
L1
SMC
L2
A
(L4)
VP
2
(L3)
SMC
A
4
3
2
VG
SMC
A
1
2
P=16
SMC
A
2
19
2
5.5
Stations
D side
≅300
VQ
0.7
17
70
3
VQZ
(Lead wire)
L plug connector (L)
DIN terminal (Y)
Indicator light
83
≅300
(Lead wire)
87
MAX.10
50.5
Applicable cord O.D.
Indicator light
ø3.5 to ø7
Cover dia ø1.5
Cross section 0.23mm2
3
1
P
80
72.5
54.5
R
Cover dia ø1.5
Cross section 0.23mm2
89
77
56
≅300
(Lead wire)
M plug connector (M)
Indicator light
Pg.7
R
Dimensions
n
L
L1
L2
L3
L4
2
43
54
75
85.5
3
1
P
Equation L1=16n+11 L2=16n+22
3
59
70
100
110.5
4
75
86
112.5
123
5
91
102
125
135.5
6
107
118
137.5
148
7
123
134
162.5
173
n: Station (Max. 20)
8
139
150
175
185.5
9
155
166
187.5
198
10
171
182
212.5
223
11
187
198
225
235.5
12
203
214
237.5
248
13
219
230
250
260.5
14
235
246
275
285.5
15
251
262
287.5
298
16
267
278
300
310.5
17
283
294
325
335.5
18
299
310
337.5
348
19
315
326
350
360.5
20
331
342
362.5
373
2.9-15
VQZ100/200/300 Body Ported
≅17.5
Cover dia ø1.6
Cross section 0.34mm2
63
56
3
1
P
9
R
(11)
(24)
PE port
2-1/4
R(EXH) port
33
(11)
(7.5)
24
(02)
Grommet (G)
(C10)
≅10.5
VV3QZ32- Station C-Q
(C6, C8)
VQZ300
2-1/4
P(SUP) port
21 10
41
n-C6, C8, C10, 02
C6: One-touch fittings for ø6
C8: One-touch fittings for ø8
C10: One-touch fittings for ø10
02: Rc(PT)1/4
(35)
(5.5)
2-ø4.5Mounting holes
DIN rail clamp screw
(2.5)
U side
n
Manual override
5
A
4
L2
L1
(L3)
(L4)
2
A
3
2
A
A
2
6
1
2
21 P=19
2
Stations
D side
1.8
20.5
≅300
3.5
75.5
(Lead wire)
DIN terminal (Y)
L plug connector (L)
≅300
(Lead wire)
88.5
Indicator light
Pg.7
MAX.10
92.5
56
Indicator light
R
3
1
P
Applicable cord O.D.
85.5
78
Cover dia ø1.5
Cross section 0.23mm2
60
ø3.5 to ø7
R
82.5
(Lead wire)
≅300
M plug connector (M)
3
1
P
94.5
Cover dia ø1.5
Cross section 0.23mm2
61.5
Indicator light
R
Dimensions
n
L
L1
L2
L3
L4
2
49
61
87.5
98
2.9-16
3
1
P
Equation L1=19n+11 L2=19n+23
3
68
80
100
110.5
4
87
99
125
135.5
5
106
118
137.5
148
6
125
137
162.5
173
7
144
156
187.5
198
n: Station (Max. 20)
8
163
175
200
210.5
9
182
194
225
235.5
10
201
213
237.5
248
11
220
232
262.5
273
12
239
251
275
285.5
13
258
270
300
310.5
14
277
289
312.5
323
15
296
308
337.5
348
16
315
327
350
360.5
17
334
346
375
385.5
18
353
365
387.5
398
19
372
384
412.5
423
20
391
403
425
435.5
VQZ100/200/300 Body Ported
Manifold Options
Blank plate
VVQZ100-10A-2
VVQZ200-10A-2
VVQZ300-10A-2
This is used when removing the valve for maintenance,
or reserving a valve mounting space on the manifold for
future use.
SY
SYJ
VK
Blank plug
VZ
KQ2P-23
KQ2P-04
KQ2P-06
KQ2P-08
KQ2P-10
L
Dimensions
øD
A
VT
One-touch
fitting ød
Part No.
A
3.2
4
6
8
10
KQ2P-23
KQ2P-04
KQ2P-06
KQ2P-08
KQ2P-10
16
16
18
20.5
22
L
D
31.5 3.2
32
6
35
8
39 10
43 12
VT
VP
VG
L
DIN rail
12.5 5.25
(Pitch)
AXT100-DR-
VQ
35
25
∗ Enter suffix number into from the table below.
Refer to the manifold dimensions for the L dimension.
To order a manifold with DIN rail already attatched,
insert "D" at the end of the manifold part number.
The DIN rail is approximately 30mm longer than the
length of manifold.
7.5
5.5
VQZ
1.25
L dimension
No.
L
L=12.5n+10.5
1 2 3 4 5 6
7 8 9 10 11 12 13 14 15 16 17 18 19 20
23 35.5 48 60.5 73 85.5 98 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5 248 260.5
No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
L 273 285.5 298 310.5 323 335.5 348 360.5 373 385.5 398 410.5 423 435.5 448 460.5 473 485.5 498 510.5
EXH port silencer
Silencer is installd in the EXH port.
63
ø22
38
ø13
Dimensions
AN110-01
Model
AN200-02
VQZ100
VQZ200
VQZ300
Silencer P/N
AN110-01
AN110-01
AN200-02
2.9-17
Series VQZ
Body Ported
Option
External Pilot Specification
Inch Size One-touch Fittings and Optional Thread
The external pilot specification is used when the operating pressure is
below the minimum operating pressure 0.1 to 0.2MPa or when valve is
used for a vacuum application.
For the external pilot valve, an "R" should be attached to the valve and the
manifold part number.
Manifolds are available with inch size one-touch fittings and NPT, NPTF or
PF type threads.
Example/Valve
VQZ212R
5M
How to Order Valve
VQZ212
N7 T -Q
5M
C6-Q
External pilot specification
Thread
(Cylinder ports,
and P/R ports)
Rc(PT)
—
External pilot port
N
NPT
M3 (VQZ200)
M5 (VQZ300)
T
NPTF
F
G(PF)
Note) R port of VQZ200
is only PF 1/16
Cylinder ports
Symbol
M5
02
M5
1/4
(
Operating press. range
)
(1)
N1
VQZ 100
(2)
Metal
seal
External
pilot
pressure Rubber
seal
range
(1) VQZ100:
Poppet
N7
N11
Pressure specifications
Series
N3
Tube O.D. (Inch) ø1/8" ø5/32" ø1/4" ø5/16" ø3/8"
VQZ100
VQZ200,VQZ300
—
0.1 to 0.7MPa
A, B
port
VQZ 200
—
VQZ 300
—
N9
—
—
—
—
—
—
—
—
Note) Millimeter size One-touch fittings (C) are
also available.
0.2 to 0.7MPa
0.15 to 0.7MPa
How to Order Manifold
Vacuum to 0.7MPa
Note 1) In case of the high pressure style, the upper limit of max.
operating pressure and external pressure range is 1MPa.
Note 2) If VQZ100 is applied in vacuum, vacuum from P port. When
finishing the vacuum application, supply pressure from R
port. Make sure that the supply pressure is less than half of
the external pilot pressure.
VV3QZ22
05C
00T -Q
Thread
(P/R port)
—
Rc(PT)
00N
NPT
00T
NPTF
00F
G(PF)
Dust Tight/Jet Proof (IP65)
Optional IP65 model is available on valves with DIN connector
electrical entry.
How to Order Valve
(Applicable to VQZ200/300 rubber seal style only)
VQZ332
5YZB W
02-Q
IP65 rated
No (standard)
—
W
(1)
IP65 rated
Note 1) The pilot exhaust of
the IP65 valves is
common with main
valve exhaust.
(The standard valve
has an individual
exhaust for the pilot
valve.)
2.9-18
Series VQZ
Body Ported
Replacement Parts
One-touch Fitting Assembly (For cylinder port)
Fitting size
C3
C4
C6
VVQ1000-50A-C3
VVQ1000-50A-C4
VVQ1000-50A-C6
Series
VQZ100, 200
VQZ300
C8
VVQ1000-51A-C6
C10
M5 (VQZ100 only)
VVQ1000-50A-M5
VVQ1000-51A-C8
VVQ1000-51A-C10
SY
Note) Orders accepted in 10 pcs. units.
SYJ
Plug connector assmbly
Gasket and screw assembly
DC (+COM)
• Single
• Latching
—
6
10
20
30
AXT661-13ADC (-COM)
• Latching
AXT661-13AN-
300mm
600mm
1000mm
2000mm
3000mm
AXT661-12A
VQZ100
VQZ100-GS-2
VQZ200
VQZ200-GS-2
VQZ300
VQZ300-GS-2
Note) Above part number consists of a
10 pcs. units with one gasket and two
screws. Orders are accepted in 10 pcs.
units.
Standard wire length of valve with plug connector
is 300mm.
When requiring valve with 600mm length lead
wire specify the model number of valve without
plug connector and the plug connector assembly.
Only connector
and sockets (3 pcs.)
VK
Part No.
Lead wire length
AXT661-14A-
VZ
VT
VT
VP
VG
Pilot valve assembly
VQ11 1
5 G
Q
VQ
Series
0
VQZ100
1
VQZ200, 300
VQZ
Function
Symbol
Specification
—
Standard
K (1)
High pressure
(Metal seal only)
Y
Low wattage
L(3)
Latching
DC
AC
(1.0W)
(1.0W)
—
(0.5W)
—
(1.0W)
Note 1) Option
Note 2) When specifying more than one option,
please indicate them alphabetically.
Note 3) K (High pressure) and Y (Low wattage)
are not available.
Electrical entry: L/M plug connector only.
Coil voltage
1*
2*
5
6
9
Order
Made
100V AC (50/60 Hz)
200V AC (50/60 Hz)
24V DC
12V DC
Others (50V or less)
Electric entry
Symbol
G
L
LO
M
MO
Y (1)
YO (1)
YZ (1)
YOS (1)
Electrical entry
Grommet (DC specification)
L plug connector with lead wire
L plug terminal without connector
M plug connector with lead wire
M plug terminal without connector
DIN terminal
DIN terminal without connector
DIN terminal
DIN terminal without connector
Light and surge
voltage suppressor
Without
With
Without
With
With (Without light)
Note 1) DIN is applicable to VQZ 200 and 300.
Note 2) Electrical entry of pilot valve for VQZ100 (L and M) is opposite side
of valve body part number.
Valve style
Pilot valve style
Contact SMC
for other voltages (9)
VQZ115-L-Q
VQ110-M-Q
∗ DIN type only available.
VQZ115-M-Q
VQ110-L-Q
2.9-19
3 Port Solenoid Valve
Metal Seal/Rubber Seal
Base Mounted
VQZ100/200/300
Variations
Nl/min
Metal/Rubber
Configuration
Voltage
Electrical
entry
Light and surge
voltage suppressor
Manual override
VQZ100
Grommet (G)
(Poppet)
295
(A)
2
VQZ200
31
(R)(P)
N.C.
3 Port
Base Mounted
—
589
687
(A)
2
L plug
connector (L)
(Standard)
12V DC
24V DC
(Made to order)
100V AC
110V AC
M plug
connector (M)
3 1
(R)(P)
Non-locking
push style
(Flush)
L plug
connector (L)
M plug
connector (M)
N.O.
(Except for VQZ100)
VQZ300
DIN connector
(Y)
883
DIN connector
(YZ)
for
( Except
VQZ100 )
1178
for
( Except
VQZ100 )
2.9-20
Indicator light and
surge voltage
suppressor
Locking style
(Slotted)
VQZ100/200/300 Base Mounted
Precautions
Be sure to read before handing. Refer to p.0-33 to 0-36 for Safety Instructions and common precautions.
Caution
Warning
Manual Override
How to Use L and M Plug Connector
Without an electric signal for solenoid valve the manual
override is used for switching the main valve.
Connection/Disconnection of connector
Connection:
Push the connector straight onto
the pins of solenoid, making sure
the lip of the lever securely "locks"
into the groove of the solenoid
cover.
M plug connector
Cover
Pin
Non-locking push style (Flush)
Push down on the manual
override button with a small
screwdriver until it stops.
Release the screwdriver and
the manual override will
return.
Disconnection:
Press the lever against the
connector housing and pull it
outward from the solenoid.
Groove
L plug connector
Cover
VG
Lever
Groove
Hook
VQ
Socket
VQZ
Connection and Electrical Circuit
With light and surge voltage suppressor
Turn the manual override
clockwise by 180° to set the mark to "1" and press it in the
direction indicated by arrow,
then it will be locked in the ON
state.
Turn the manual override
counterclockwise by 180° to set
the mark to "0", then it will be
reset.
VZ
VP
Refer to p.2.9-39 for part No.
of plug connector ass'y.
Locking style (Slotted) VQZ100
VK
VT
Lead wire
0.2 to 0.33mm2
(Max. O.D. ø1.7mm)
Locking style (Slotted) VQZ200/300
SYJ
VT
Connector
Pin
Push down on the manual
override button with a small
screwdriver until it stops.
While down, turn clockwise
by 90° to lock it. Turn it
counterclockwise to release it.
SY
Circuit for DC
Circuit for AC
A (–)
(+)
Light
A
SOL
C(+)
(–) Light
SOL
C
ZNR
Due to the use of non-polar light, the VQZ series has no polarity.
Refer to p.1.12-26 for the latching style.
2.9-21
Series
VQZ
Base Mounted
Precautions
Be sure to read before handling. Refer to p.0-33 to 0-36 for Safety Instructions and common precautions.
Connection of Lead Wire (Not necessary if ordering pre-connected model.)
How to Wire the DIN Connector
Crimping connection of lead wire and socket
Conforming to ISO/DIN 43650C (8mm between pins)
Cut the power and air supply before mounting/
removing the connector.
Strip 3.2 to 3.7mm of the lead wire ends, insert each stripped wire into a
socket and crimp it using the special crimping tool. Be careful that the
outer insulation of the lead wires does not interfere with the socket contact
part.
Crimping area
Core wire
contact area
qLoosen the top screw and remove the connector housing from the
terminal spades on the solenoid.
wRemove the housing screw and insert a screwdriver into the slot area on
Core wire
Socket
0.2 to 0.33mm2
Max.cover diameter: ø1.7mm
the underside of the DIN cap and carefully separate block and housing.
eLoosen the terminal screws of the block and insert stripped lead wires
in accordance with the wiring diagram. Secure each wire by retightening
the terminal screw.
rTighten the housing grommet nut to secure the cable wire.
Lead wire
Change of the electrical entry
Insulation
Hook
Tool for crimping: Model No. DXT170-75-1
Connection/Disconnection of socket with lead wire
Connection
Insert lead wire and crimped socket into square holes (Indicated as A,B,
COM) of connector. Press the socket in fully until the hook of the socket
locks into the groove of the connector housing. Confirm the locked positon
by lightly pulling on the lead wire.
Discoonnection
To remove the socket from the connector, pull out lead wire while
depressing the hook of the socket with a fine screw driver. If
the socket is to be re-used, reposition the hook again.
Once the housing is separated from the terminal block, rotate it in any
direction to change the orientation of the electrical entry.
∗ In the case of the indicator light option, avoid damaging the light with the
lead wire connections.
Precaution
Pull connector out vertically, never at an angle.
Applicable cable
Cord O.D. : ø3.5 to ø7
(Reference) 0.5mm2 2-core and 3-core wires equivalent to JISC3306.
Connector
Ground nut
Lead wire
Fix screw
Washer
Grommet
(Rubber)
Socket
housing
(Voltage symbol)
Refer to below table.
(Position for light mounting)
Terminal block
Hook
Change in Piping Direction for VQZ100 Only
One-touch fitting
Shaved part
Terminal thread
(3 position)
Part No. for DIN connector (Based on DIN)
Port plug
(VVQZ100-CP)
Without light
K41
With light
Rated voltage
24V DC
12V DC
100V AC
110V AC
Clip
PR plate
qChanging the piping direction from
VQZ100-12A (Standard)
in-line to perpendicular (port on the
VQZ100-12B (External pilot)
valve) is possible on the VQZ100
∗ 2 mounting screws are included with
series. Follow the steps below to
each plate.
change piping direction:
wA base mount VQZ100 valve
Remove the fitting clips that hold
can be converted to an individual
the fitting and port plug in place.
in-line (body ported) valve by
Remove the fitting and port plug
installing an adapter plate on the
Insert the fitting in previous port
mounting surface of the valve.
plug position and insert port plug
in fitting's previous position.
Replace the fitting clips.
2.9-22
Voltage symbol
24V
12V
100V
110V
Part No.
K42
K44
Caution
Mounting 3 port valves on 5 port manifolds
1
Valve Mounting
1
(VQZ 23 85 01 ,N.C./VQZ 23 95 01 ,N.O.)
When a 3 port valve is mounted on a 5 port manifold,
The "A" port is the working port. The "B"port can either
be plugged or unplugged.
5 port valve
3 port valve
After confirming the gasket is correctly placed under
the valve, tighten the mounting screws with the
appropriate torque listed below.
Model
Suitable tightening torque
VQZ100
0.13 to 0.19Nm
VQZ200
0.25 to 0.35Nm
VQZ300
0.5 to 0.7Nm
SY
SYJ
When port plug is used on B port,
indicate "CM" in manifold part No. and
port size, and specify the port plug
location on the manifold specification form.
VK
VZ
Port plug
VT
Changing One-touch Fittings
The built-in fittings on the manifold can be changed
easily. Simply remove the corresponding valve and take
out the fitting clip underneath. Then remove the affected
fitting and replace it with a new one. Finally, replace the
fitting clip and remount the valve.
VT
VP
Screw
VG
Clip
VQ
VQZ
One-touch Fitting Ass'y
Precaution
When pull the fitting assembly away from the manifold base,
remove the clip, then connect a tube or plug (KQP-)
with the One-touch fitting and pull out it while holding the tube
or plug. Do not hold the release button to avoid damage.
DIN Rail Removal/Mounting
To remove manifold from DIN rail:
1) Loosen the clamp screw on the "A"
side of both ends of the manifold.
2) Lift the "A" side of the manifold off
the DIN rail and slide it in the
direction of the "B" side.
Mounting manifold to DIN rail:
1) Catch the hook of the DIN rail
Clamp screw
bracket on the "B" side on the
DIN rail.
2) Push side "A" onto the DIN rail
and tighten the clamp screw.
(Tightening torque of 0.3 to 0.4
Nm)
A
B
2.9-23
3 Port Solenoid Valve
Base Mounted
VQZ100/200/300
Plug Lead Unit
Valve Single Unit
How to Order Valve VQZ100
VQZ 1 1 5
5 M
Q
01
Series
Thread
1
N
T
F
VQZ100 Body width10mm
Configuration
(A)
2
N.C.
1
Port size {2(A)port}
13
(P) (R)
CP
01
Body style
5
Rc (PT)
NPT
NPTF
G (PF)
Without sub-plate
1/8
Manual override
Base mounted
—: Non-locking B: Locking style
(Slotted)
push style
(Flush)
Function
Symbol
Specification
—
Standard
K (1)
High pressure
Y
Low wattage
R
External
DC
Electrical entry
(1.0W)
G: Grommet L: L plug
LO: L plug
M: M plug
MO: M plug
(DC
connector
terminal without connector
terminal without
specification) with lead wire connector
with lead wire connector
(1.0W)
(0.5W)
With indicator light and
surge suppressor
With indicator light and With indicator light and
surge suppressor
surge suppressor
Note 1) Option
Note 2) When specifying more than
one option, indicate them
alphabetically.
Note) Standard lead wire length: 300mm
Coil voltage
Protective class
class III (Mark:
)
5
6
9
Order
Made
2.9-24
24V DC
12V DC
Other (50V or less)
Contact SMC
for other voltages (9)
With indicator light and
surge suppressor
VQZ100/200/300 Base Mounted
How to Order Valve VQZ200/300
VQZ 2 1 5
Q
5 M
Series
Thread
2
3
N
T
F
VQZ200 Body width 15mm
VQZ300 Body width 18mm
Rc (PT)
NPT
NPTF
G (PF)
SY
SYJ
Configuration
1
N.O.
Port size {2(A)port}
(A)
2
31
(R) (P)
(A)
2
Symbol
Metal seal
N.C.
01
02
03
2
31
(R) (P)
(A)
2
VT
—
VT
(Slotted)
VP
Rubber seal
N.O.
push style
(Flush)
VK
VZ
—
-: Non-locking B: Locking style
(A)
2
3
VQZ200 VQZ300
Manual override
31
(R) (P)
N.C.
Port size
Without sub-plate
1/8
1/4
3/8
VG
4
31
(R) (P)
Electrical entry
G: Grommet L: L plug
LO: L plug
M: M plug
MO: M plug
(DC
connector
terminal without connector
terminal without
specification) with lead wire connector
with lead wire connector
∗
∗
∗
∗
Body style
Base mounted
5
Y: DIN
terminal
Function
Symbol
(1)
K
Y
R
Specification
Standard
High pressure
(Metal seal only)
(1.0W)
Low wattage
(0.5W)
AC
—
External pilot
Protective class
class I (Mark:
)···DIN terminal type
With surge
voltage
suppressor
—
Note 1) Option
Note 2) When specifying more than one
option, indicate them alphabetically.
Note) Standard lead wire length: 300mm.
∗With light and surge voltage suppressor.
Coil voltage
1∗
3∗
5
6
9
Order
Made
)···Other
YOS: DIN
terminal without
connector
∗
DC
(1.0W)
Protective class
class III (Mark:
YO: DIN
YZ: DIN
terminal without terminal
connector
100V AC (50/60Hz)
110V AC (50/60Hz)
24V DC
12V DC
50V or less
Contact SMC
for other voltages (9)
∗ DIN only available.
2.9-25
VQ
VQZ
VQZ100/200/300 Base Mounted
Standard Specifications
Seal
Metal seal
Rubber seal
Fluid
Air, Inert gas
Air, Inert gas
Max.operating pressure
0.7MPa (High pressure style: 1.0MPa)
Min.operating pressure
0.1MPa
–10 to 50°C
Valve
Ambient and fluid temp.
5Hz
Individual EXH
Pilot valve EXH
Not required
Lubrication
Non-locking push style/Locking slotted style
Manual override
Shock/Vibration resistance (2)
150/30 m/s2
Dust proof
Enclosure
12V, 24V DC 100V, 110V AC
±10% of rated voltage
Coil rated voltage
Allowable voltage
Solenoid
(1)
20Hz
Max.operating frequency
Class B
Coil insurance
Power
consumption
(Current
value)
0.7MPa
0.15MPa
–10 to 50°C (1)
1W DC (42mA), 0.5W DC (21mA)
24V DC
12V DC
1W DC (83mA), 0.5W DC (42mA)
100V AC
Inrush 0.5VA (5mA), Holding 0.5VA (5mA)
110V AC
Inrush 0.55VA (5mA), Holding 0.55VA (5mA)
Note 1) Use dry air to prevent condensation when operating at low temperatures.
Note 2) Shock resistance: No malfunctions resulted from the impact test using a drop impact tester.
The tests were performed on the axis and right angle direction of the main
valve and armature, for both energized and de-energized states. (Value
in the initial stage.)
Vibration resistance: No malfunctions occurred in a one-sweep test between 8.3 and 2,000 Hz.
Tests were performed at both energized and de-energized states to the
axis and right angle direction of the main valve and armature. (Value in
the initial stage.)
Model
Series
Valve configuration
Model
Effective area(mm2)
(Nl/min)
VQZ100
N.C.
N.C.
VQZ200
N.O.
N.C.
VQZ300
N.O.
(1)
Response time (ms) (2)
Standard: 1W
High pressure: 1W
Low wattage and AC
Poppet
VQZ115
10 or less
13 or less
Metal
VQZ215
10.8 (588.9)
14 or less
18 or less
Rubber
VQZ235
12.6 (687.05)
15 or less
20 or less
Metal
VQZ225
10.0 (539.83)
14 or less
18 or less
Rubber
VQZ245
12.6 (687.05)
15 or less
20 or less
Metal
VQZ315
16.2 (883.35)
17 or less
22 or less
Rubber
VQZ335
21.6 (1177.8)
25 or less
33 or less
Metal
VQZ325
15.3 (834.28)
17 or less
22 or less
Rubber
VQZ345
21.6 (1177.8)
25 or less
33 or less
5.4 (294.45)
Note 1) Valve of sub-plate and maximum diameter.
Note 2) As per JIS8375-1981 (Supply pressure: 1.5MPa; with indicator light and surge voltage suppressor; clean air) The response time is
subject to the pressure and the air quality. The values at the time of ON are given for the double styles.
Note 3) Weight without sub-plate.
2.9-26
(3)
Weight (g)
25
53
77
VQZ100/200/300 Base Mounted
Construction
VQZ100
Poppet
e
r
q
Component Parts
w
Material
N.C.
No.
(A)
2
q
Body
Resin
w
e
r
Spool valve
Aluminium/NBR
13
(P) (R)
Description
Notes
SYJ
Pilot valve
Port plug
Resin/NBR
SY
VVQZ100-CP
VK
VZ
VT
VQZ200/300
Metal seal
VT
Rubber seal
VP
r
e
w
q
r
e
w
VG
q
VQ
VQZ
N.C.
r
e
w
N.C.
(A)
2
(A)
2
31
(R) (P)
31
(R) (P)
q
r
N.O.
e
w
q
N.O.
(A)
2
(A)
2
31
(R) (P)
31
(R) (P)
Component Parts
No.
q
Description
Material
Note
Body
Aluminium die cast
Spool/Sleeve
Stainless steel
Metal seal
Spool valve
Aliminium/NBR
Rubber seal
e
Piston
Resin
r
Pilot valve
w
2.9-27
VQZ100/200/300 Base Mounted
Dimensions: VQZ100
Valve single unit
≅300
(Lead wire)
Grommet (G): VQZ115(R)-G-01-Q
Cover diameter ø1.6
Cross section 0.34mm2
7
12
7.5
14.5
3-1/8
P/A/R port
M5
PE port
53
2- ø3.4Mounting holes
14.5
14.5
3.5
R3
.5
12 X
10
2 A
Manual override
1 P
34
41
L plug connector (L): VQZ115(R)-L-01-Q
3 R
3.5
M plug connector (M): VQZ115(R)-M-01-Q
60.5
≅300
(Lead wire)
≅300
(Lead wire)
24
M5 External pilot port
(Only external pilot style (R))
PE
7.5
7.5
16
A port
35.5
38.5
SMC
Indicator light
2.9-28
51.5
Cover dia ø1.5
Cross section 0.23mm2
45
Indicator light
Cover diameter ø1.5
Cross section 0.23mm2
55.5
VQZ100/200/300 Base Mounted
Dimensions: VQZ200
Valve single unit
01
3-1/8,1/4
10.5
(1/8)
SYJ
M5 External pilot port
(Only external pilot style (R))
VK
10
(1/4)
18
(1/4)
P/A/R port
SY
A port
9
16
9
17
(1/8)
PE port
13.5
22
45
51
Grommet (G): VQZ25(R)-G- 02 -Q
VZ
VT
32
4
19.2
Manual override R4
VT
2 A
3 R
34
15
VP
SMC
Cover dia ø1.6
Cross section 0.34mm2
4
2-ø4.5 Mounting holes
VG
1 P
40
≅300
70
(Lead wire)
L plug connecter (L): VQZ25(R)-L-
01
02 -Q
VQ
DIN terminal (Y): VQZ25(R)-Y- 01
02 -Q
VQZ
Indicator light
83
≅300
(Lead wire)
Pg.7
≅300
(Lead wire)
M plug connecter (M): VQZ25(R)-M- 01
02 -Q
87
Indicator light
56.5
82.5
Applicable cord O.D.
ø3.5 to ø7
MAX.10
75
53
Cover dia ø1.5
Cross section 0.23mm2
Cover dia ø1.5
Cross section 0.23mm2
77
89
58
Indicator light
2.9-29
VQZ100/200/300 Base Mounted
VQZ300
Valve single unit
02
3-1/4,3/8
P/A/R port
19
(1/4)
14
(1/4)
21
(3/8)
13
(3/8)
37
2-ø4.5Mounting holes
45
18
2 A
3 R
1 P
47
≅300
76
(Lead wire)
02
L plug connecter (L): VQZ35(R)-L- 03 -Q
DIN terminal (Y): VQZ35(R)-Y- 02
03 -Q
Indicator light
88.5
≅300
(Lead wire)
Pg.7
56.5
Cover dia ø1.5
Cross section 0.23mm2
MAX.10
92.5
Indicator light
78.5
86
Applicable cord O.D.
ø3.5 to ø7
62
Indicator light
≅300
(Lead wire)
M plug connecter (M): VQZ35(R)-M- 02
03 -Q
2.9-30
Cover dia ø1.5
Cross section 0.23mm2
82.5
95
20.5
17.5
5
23.5
R5
Cover dia ø1.6
Cross section 0.34mm2 Manual override
M5 External pilot port
(Only external piot style (R))
5
PE port
9
11.5
A port
11.5
26.5
54.5
56.5
Grommet (G): VQZ35(R)-G- 03 -Q
3 Port Solenoid Valve
Base Mounted
VQZ100/200/300
Plug Lead Unit
Manifold
Connector Kit
How to Order Manifold VQZ100
VV3QZ 1 5
08 C6
C
D
Q
SY
Option
—
D
DO ∗
R
Series
1
VQZ100
Kit
Connector
C
∗ Order DIN rail separately.
Thread
Manifold style
5
N
T
F
Base mounted
Stations
None
DIN rail mounting (DIN rail standard length)
DIN rail mounting (Without DIN rail)
External pilot
VT
…
…
VT
Port size{2(A)Port}
C3
C4
C6
M5
CP (1)
CM (2)
N1
N3
N7
NM
M5T
One-touch fitting for ø3.2
One-touch fitting for ø4
For lateral
One-touch fitting for ø6
piping
M5 thread (Changeable style)
With port plug
For top piping
Mixture port
—
One-touch fitting for ø1/8
One-touch fitting for ø5/32
For lateral
One-touch fitting for ø1/4
piping
Mixed size
10-32 UNF thread
VP
VG
VQ
Note 1) In case of CP port plug is attached on
all 2(A) port.
Valve on manifold is top piping.
Note 2) Specify the mixture port(including top and side piping)
on the maifold specification form.
VQZ
How to Order Valve VQZ100
VQZ 1 1 5
Q
5 M
Port size
Series
1
CP
C3
C4
C6
M5
VQZ100 Body width 10mm
1
—
B
N.C.
—
K
Standard
(1)
Y
R
Specification
High pressure
Low wattage
(2)
Top
piping
Electrical entry
Base mounted
Symbol
G
L
LO
M
MO
Function
Symbol
Lateral piping
Non-locking push style (Flush)
Locking style (Slotted)
Body style
5
With port plug
One-touch fitting for ø3.2
One-touch fitting for ø4
One-touch fitting for ø6
M5 thread
Manual override
Configuration
DC
(1.0W)
AC
(3)
Coil voltage
(1.0W)
—
(0.5W)
—
External pilot
Note 1) Option
Note 2) Refer p.2.9-38 for details about
external pilot specification.
Note 3) Refer p.2.9-26 for power
consumption of AC type.
Note 4) When specifying more than
one option,indicate them
alphabetically.
5
6
9
Order
Made
VK
VZ
Rc (PT)
NPT
NPTF
G (PF)
02 2 stations
20 20 stations
SYJ
Electrical entry
Light and surge
suppressor
Grommet (DC spacification)
L plug connector with lead wire
L plug terminal Without connector
M plug connector with lead wire
M plug terminal Without connector
Without
With
Note) Standard lead wire length: 300mm.
24V DC
12V DC
Others (50V or les)
Contact SMC
for other voltages (9)
2.9-31
VQZ100/200/300 Base Mounted
How to Order Manifold VQZ200/300
VV3QZ 2 5
08 C6
C
Q
D
Option
Series
2
3
VQZ200
VQZ300
Kit
C
∗ Order DIN rail separately.
Thread
Manifold type
5
Connector
N
T
F
Base mounted
Stations
None
DIN rail mounting (DIN rail standard length)
DIN rail mounting (Without DIN rail)
External pilot
—
D
DO ∗
R
Rc (PT)
NPT
NPTF
G (PF)
…
…
02 2 stations
Port size{2(A)Port}
20 20 stations
Symbol
C4
C6
C8
C10
01
02
CM(1)
N3
N7
N9
N11
NM
VQZ200 VQZ300
—
Port size
One-touch fitting for ø4
One-touch fitting for ø6
One-touch fitting for ø8
One-touch fitting for ø10
Rc(PT)1/8
Rc(PT)1/4
Mixture port
One-touch fitting for ø5/32
One-touch fitting for ø1/4
One-touch fitting for ø5/16
One-touch fitting for ø3/8
Mixed size
—
—
—
—
—
Note 1) Specify port mixture/with port plug by means of manifold
specification sheet. Port mixture and port plug are available
only for One-touch fitting type.
How to Order Valve VQZ200/300
VQZ 2 1 5
Series
2
3
Q
5 M
Manual override
VQZ200 Body width15mm
VQZ300 Body width18mm
—
B
Non-locking push style (Flush)
Locking style (Slotted)
Electrical entry
Symbol
Configuration
1
2
3
4
N.C.
N.O.
N.C.
N.O.
G
L
LO
M
MO
Y
YO
YZ
YOS
Metal seal
Metal seal
Rubber seal
Rubber seal
Body style
5
Base mounted
Function
Symbol
—
K
(1)
Y
R
(2)
Specification
DC
Grommet (DC specification)
L plug connector with lead wire
L plug terminal without connector
M plug connector with lead wire
M plug terminal without connector
DIN terminal
DIN terminal without connector
DIN terminal
DIN terminal without connector
Light and surge
voltage suppressor
Without
With
Without
With
With (Without light)
Note) Standard lead wire length: 300mm.
AC
(3)
Standard
(1.0W)
High pressure
(Metal seal only)
(1.0W)
—
Low wattage
(0.5W)
—
External pilot
Note 1) Option
Note 2) Refer to p.2.9-38 for details about
external pilot specificaton.
Note 3) Refer to p.2.9-26 for power
consumption of AC type.
Note 4) When specifying more than one
option, indicate them alphabetically.
2.9-32
Electrical entry
Coil voltage
1∗
2∗
5
6
9∗
Order
Made
100V AC (50/60Hz)
200V AC (50/60Hz)
24V DC
12V DC
Others (50V or less)
Contact SMC
for other voltages (9)
∗ DIN only available.
VQZ100/200/300 Base Mounted
Specification
Piping specification
Series
Base model
Piping
VQZ100 VV3QZ15--Q
VQZ200 VV3QZ25--Q
VQZ300 VV3QZ35--Q
Side
⋅
Top
Side
Side
Port size
1(P), 3(R)
1/8
1/4
1(P)port
3/8
3(R)port
1/4
2(A)
(1)
Applicable Applicable Manifold
base
valve
station weight (g)
C3 (for ø3.2)
C4 (for ø4)
VQZ15
C6 (for ø6)
M5 (M5 thread)
C4 (for ø4)
C6 (for ø6)
C8 (for ø8)
Rc(PT)1/8
C6 (for ø6)
C8 (for ø8)
C10 (for ø10)
Rc(PT)1/4
2 to 20
2 stations:83
Additional
station:19
2 to 20
2 stations:126
Additional
station:38
2 to 20
2 stations:209
Additional
station:60
SY
VQZ25
SYJ
VK
VQZ35
VZ
VT
Note 1) Threaded port style.
VT
VP
How to Order Manifold Assembly (Example)
VG
e
ions
U sid
Stat
5
4
VQ
VQZ215-5L 4set
3
2
D
VQZ
VV3QZ25-05C6C-Q ···· 1 set (C kit 5 stations manifold base)
VVQZ200-10A-5 ··· 1 set (Blank plate assembly)
VQZ215-5L-Q ··········· 4 sets (Single solenoid)
1
side
C6 :One-touch fitting ø6
VVQZ200-10A-5
2.9-33
VQZ100/200/300 Base Mounted
Grommet(G)
39.5
42.5
≅7.8
≅300
(Lead wire)
Cover dia ø1.6
Cross section 0.34mm2
R
8
1 3
2-M5
PE port
2-1/8
P(SUP) port
41.2
46.5
(35)
(11)
27
(7.5)
20
11.7
≅2-1/8
R(EXH) port
13.4
16.3
15
P
n-C3,C4,C6,M5
C3: One-touch fitting for ø3.2
C4: One-touch fitting for ø4
C6: One-touch fitting for ø6
M5: M5 thread
(Top piping)
Dimensions: VQZ100
VV3QZ15- Station Port size C-Q
(5.5)
2-ø4.5 Mounting holes
(4.5)
DIN rail clamp screw
U side
A
2
5.5
n
5
Maual override
A
L1
(L4)
(L3)
L2
P=10.5
2A
2
2A
3
P=10.5
4
2A
1
16 .5
13.5
A
2
2
6 .5
5.5
Station
D side
2.3
2-M5 External pilot port
(Only external pilot style(R))
M plug connector (M)
49
Cover dia ø1.5
Cross section 0.23mm2
L1
L2
L3
L4
2
30.5
43.5
75
85.5
2.9-34
61
55.5
Indicator light
Cover dia ø1.5
Cross section 0.23mm2
≅300
(Lead wire)
66
≅300
(Lead wire)
Indicator light
n
5.5
53
L plug connector (L)
L
(M5: 5.7)
35
The broken line indicates DIN rail mounted style [-D].
Dimensions
≅7.8(C3, C4, C6)
21.6
Equation
3
41
54
75
85.5
1
L1=10.5n+9.5
4
51.5
64.5
87.5
98
5
62
75
100
110.5
R
P
P
R
1
3
3
n: Station (Max.20)
L2=10.5n+22.5
6
72.5
85.5
112.5
123
7
83
96
125
135.5
8
93.5
106.5
137.5
148
9
104
117
137.5
148
10
114.5
127.5
150
160.5
11
125
138
162.5
173
12
135.5
148.5
175
185.5
13
146
159
187.5
198
14
156.5
169.5
200
210.5
15
167
180
200
210.5
16
177.5
190.5
212.5
223
17
188
201
225
235.5
18
198.5
211.5
237.5
248
19
209
222
250
260.5
20
219.5
232.5
262.5
273
VQZ100/200/300 Base Mounted
Dimensions: VQZ200
VV3QZ25- Station
C-Q
Port size
Cover dia ø1.6
Cross section 0.34mm2
R
3
1
P
25.5
PE port
11
(30)
59
Grommet (G)
M5 External pilot port
(Only external pilot style (R))
20
2-1/4
R(EXH)port
≅11
43.5
2- ø4.5Mounting holes
SYJ
DIN rail clamp screw
n-C4, C6, C8, 01
21.5
VK
(5.5)
(7.5)
30
SY
(35)
(11)
38
2-1/4
P(SUP)port
12.5
38.5
(3.5)
VZ
C4: One-touch fitting for ø4
C6: One-touch fitting for ø6
n
C8: One-touch fitting for ø8
01: 1/8
A
2
U side
VT
Manual override
VT
SMC
5
L1
P=16
L2
3
(L3)
P=16
(L4)
4
VP
2
VG
A
2
15.5
18
1
5
Station
D side
50.5
≅300
22.5
3
70
VQ
(Lead wire)
The broken line indicates DIN rail mounted style [-D].
VQZ
L plug connector (L)
DIN terminal (Y)
≅300
(Lead wire)
86
83
90
Pg.7
87
61
MAX.10
Cover dia ø1.5
Cross section 0.23mm2
R
3
1
P
Indicator light
90.5
83
Applicable cord O.D.
ø3.5 to ø7
R
3
1
P
92
80
77
Cover dia ø1.5
Cross section 0.23mm2
66
Indicator light
≅300
(Lead wire)
M plug connector (M)
R
Dimensins
Equation
n
3
58
68
87.5
98
L
L1
L2
L3
L4
2
42
52
75
85.5
L1=16n+10
4
74
84
112.5
123
5
90
100
125
135.5
3
1
P
L2=16n+20
6
106
116
137.5
148
7
122
132
162.5
173
n: Station (Max.20)
8
138
148
175
185.5
9
154
164
187.5
198
10
170
180
200
210.5
11
186
196
225
235.5
12
202
212
237.5
248
13
218
228
250
260.5
14
234
244
275
285.5
15
250
260
287.5
298
16
266
276
300
310.5
17
282
292
312.5
323
18
298
308
337.5
348
19
314
324
350
360.5
20
330
340
362.5
373
2.9-35
VQZ100/200/300 Base Mounted
VQZ300
VV3QZ35- Station
Port size
C-Q
Cover dia ø1.6
Cross section 0.34mm2
11.5
3
29.5
R P
34
62
64
Grommet (G)
1
PE port
M5 External pilot port
(Only external pilot style (R))
21
44.5
50
2-1/4
2-3/8
18
P(SUP) port
11
R(EXH)port
(11)
42
(7.5)
34
23.5
n-C6, C8, C10, 02
C6: One-touch fitting for ø6
C8: One-touch fitting for ø8
(35)
(5.5)
2-ø4.5 Mounting holes
DIN rail clamp screw
(3)
C10: One-touch fitting for ø10
U side
02: 1/4
A
2
n
Manual override
5
L2
L1
(L4)
3
(L3)
4
9
A
2
1
23
19.5 P=20
P=20
2
Station
D side
50
≅300
The broken line indicates DIN rail mounted style [-D].
29.5
75.5
3.8
(Lead wire)
L plug connector (L)
DIN terminal (Y)
≅300
(Lead wire)
92
88.5
Indicator light
96
64
MAX.10
92.5
R P
Applicable cord O.D.
Pg.7
ø3.5 to ø7
1
93.5
3
86
Cover dia ø1.5
Cross section 0.23mm2
M plug connector (M)
3
1
98.5
Cover dia ø1.5
Cross section 0.23mm2
69.5
Indicator light
≅300
(Lead wire)
R P
86
82.5
Dimensions
n
L
L1
L2
L3
L4
2.9-36
2
48
66
87.5
98
n: Stations (Max.20)
Equation L1=20n+8 L2=20n+26
3
68
86
112.5
123
4
88
106
137.5
148
5
108
126
150
160.5
6
128
146
175
185.5
7
148
166
187.5
198
8
168
186
212.5
223
9
188
206
237.5
248
10
208
226
250
260.5
11
228
246
275
285.5
12
248
266
287.5
298
13
268
286
312.5
323
14
288
306
337.5
348
15
308
326
350
360.5
16
328
346
375
385.5
17
348
366
387.5
398
18
368
386
412.5
423
19
388
406
437.5
448
20
408
426
450
460.5
VQZ100/200/300 Base Mounted
Manifold Options
Blank plate
VVQZ100-10A-5
VVQZ200-10A-5
VVQZ300-10A-5
This is used when removing the valve for maintenance,
or reserving a valve mounting space on the manifold
for future use.
SY
SYJ
VK
Blank plug
VZ
KQ2P-23
KQ2P-04
KQ2P-06
KQ2P-08
KQ2P-10
L
Dimensions
(mm)
One-touch
fitting ød
Part No.
A
3.2
4
6
8
10
KQ2P-23
KQ2P-04
KQ2P-06
KQ2P-08
KQ2P-10
16
16
18
20.5
22
øD
A
L
VT
D
31.5 3.2
32
6
35
8
39 10
43 12
VT
VP
VG
L
DIN rail
12.5
(Pitch)
AXT100-DR-
5.25
VQ
35
25
∗ Enter suffix the number from DIN rail dimensions table below.
Refer to the manifold dimensions drawings for the L dimension.
12.5
L dimensions
No.
L
VQZ
5.5
To order a manifold with DIN rail already attached,
insert "D" at the end of the manifold part number.
The DIN rail is approximately 30mm longer than the
length of manifold.
7.5
L=12.5n+10.5
1 2 3 4 5 6
7 8 9 10 11 12 13 14 15 16 17 18 19 20
23 35.5 48 60.5 73 85.5 98 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5 248 260.5
No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
L 273 285.5 298 310.5 323 335.5 348 360.5 373 385.5 398 410.5 423 435.5 448 460.5 473 485.5 498 510.5
EXH port silencer
63
Silencer is installed in the EXH port.
ø22
38
ø13
Dimensions
AN110-01
Model
AN200-02
VQZ100
VQZ200
VQZ300
Silencer P/N
AN110-01
AN200-02
AN200-02
Port plug
VVQZ100-CP
This is used when changing piping location.(Side or Top)
2.9-37
Series VQZ
Base Mounted
Option
External Pilot Specification
Inch Size One-touch Fittings and Optional Thread
The external pilot specification must be used when the operating pressure
is below the minimum operating pressure 0.1 to 0.2MPa or when valve is
being used for a vacuum application.
For the external pilot valve, an "R" should be attached to the valve and the
manifold part number. (See the below.)
Manifolds are available with inch size One-touch fittings for the cylinder
ports.
Example/Valve
How to Order Manifold
VV3QZ15
VQZ215R
5M
08 N7 T C-Q
02-Q
Thread
(Cylinder ports and
P, R ports)
External pilot specification
Example/Manifold
—
VV3QZ25
06C6C
R-Q
External pilot specification
Rc(PT)
N
NPT
T
NPTF
F
G(PF)
Cylinder ports
Symbol
External pilot port
N1
N3
N7
VQZ100
Pressure specifications
(2)
Series
VQZ100
Metal
(1)
seal
External pilot
pressure Rubber
range
seal
VQZ100:
Poppet
)
Operating press range (1)
—
VQZ200
VQZ300
ø3/8"
—
Cylinder
VQZ200
port
—
VQZ300
—
NM (1) M5
N11
Tube O.D. (Inch) ø1/8" ø5/32" ø1/4" ø5/16"
M5 X 0.8
(
N9
Mix
M5
—
—
01
02
1/8
1/4
—
—
—
—
—
—
—
Note1) Mixing One-touch fittings and thread types is impossible except
for VQZ100.
Note2) Millimeter size One-touch fittings (C) are also available.
0.1 to 0.7MPa
Optional Thread <Rc(PT) is standard. style>
Sub-bases and manifolds with NPT, NPTF or PF type threads are available.
0.2 to 0.7MPa
0.15 to 0.7MPa
0.1 to 0.7MPa 0.2 to 0.7MPa
Vacuum to 0.7MPa
Note 1) In case of the high pressure style, the upper limit of max. operating
pressureand external pressure range is 1MPa.
Note 2) If VQZ100 is applied in vacuum, vacuum from P port. When finishing
the vacuum application, supply pressure from R port. Make sure that
the supply pressure is less than half of the external pilot pressure.
How to Order Valve with Sub-base
VQZ215
5M
02 T -Q
Thread
(Cylinder ports and
P/R ports)
—
Rc(PT)
N
NPT
T
NPTF
F
G(PF)
Dust Tight/Jet Proof (IP65)
Optional IP65 model is available on valves with DIN connector electrical entry.
How to Order Valve
(Applicable to VQZ200/300 rubber style)
VQZ335
5YZB W
03-Q
IP65 rated
No (Standard)
—
W
2.9-38
(1)
IP65 rated
Note 1) The pilot exhaust of the
IP65 valves is common
with main valve exhaust.
(The standerd valve has
an individual exhaust for
the pilot valve.)
Series VQZ
Base Mounted
Replacement Parts
One-touch Fitting Assembly (For cylinder port)
Fitting size
C3
C4
C6
VVQ1000-50A-C3
VVQ1000-50A-C4
VVQ1000-50A-C6
VVQ1000-51A-C4
VVQ1000-51A-C6
VVQ1000-51A-C8
VVQ2000-51A-C6
VVQ2000-51A-C8
Series
VQZ100
VQZ200
VQZ300
C8
C10
M5 (VQZ100 only)
VVQ1000-50A-M5
SY
VVQ2000-51A-C10
Note) Order is acceppted from 10 pcs. unit.
SYJ
<Plug connector assembly>
<Gasket and screw assembly>
DC (+COM)
· Single
Lead wire length
AXT661-14A· Latching
—
6
10
20
30
AXT661-13ADC (-COM)
· Latching
AXT661-13AN100V, 110V AC
VK
Part No.
300mm
600mm
1000mm
2000mm
3000mm
Standard wire length of valve with plug connector
is 300mm.
When requiring valve with a 600mm length lead
wire specify the model number of the valve without
plug connector and the plug connector assembly.
VQZ100
VQZ100-GS-5
VQZ200
VQZ200-GS-5
VQZ300
VQZ300-GS-5
VZ
VT
Note) Above part number consists of 10
units with one gasket and two screws.
Orders are accepted in 10 pcs.units.
VT
VP
VG
<Pilot valve assembly>
VQ11 1
Q
5 G
VQ
Series
VQZ
0
VQZ100
1
VQZ1000/2000/3000
Function
Symbol
—
K
(1)
Y
L
Specification
DC
Standard
(1.0W)
High pressure
(Metal seal only)
(1.0W)
—
(0.5W)
—
Low wattage
(3)
AC
(1.0W)
Latching
Note 1) Option
Note 2) When specifying more than one option,
please indicate them alphabetically.
Note 3) K (High pressure) and Y(Low
wattage) are not available.
Electrical entry: L/M plug connector only.
Coil voltage
1∗
3∗
5
6
9∗
Order
Made
100V AC (50/60Hz)
110V AC (50/60Hz)
24V DC
12V DC
Others (50V or less)
Electrical entry
G
L (1)
LO (1)
M (1)
MO (1)
Y (2)
YO (2)
YZ (2)
YOS (2)
Grommet (DC specification)
L plug connector with lead wire
L plug terminal without connector
M plug connector with lead wire
M plug terminal without connector
DIN terminal
DIN terminal without connector
DIN terminal
DIN terminal without connector
<Sub-plate>
Note 1) L, LO, M and MO are attached light and surge
voltage suppressors as standard.
Note 2) DIN is applicble to VQZ 200 and 300.
Note 3) Electrical entry of pilot valve for VQZ100(L and M)
is opposite side of valve body part number.
Valve style
Pilot valve style
VQZ115-L-Q
VQ110-M-Q
VQZ115-M-Q
VQ110-L-Q
Model
VQZ100
Sub-plate part No.
VQZ100-S-01(R)
VQZ200
VQZ200-S-
VQZ300
VQZ300-S-
(1)
01[Rc1/8]
02[Rc1/4]
02 [Rc1/4]
03 [Rc3/8]
Note 1) Symbol "R" indicates an external pilot.
The part No. is common to the external
pilot and internal pilot style except for
VQZ100.
Contact SMC
for other voltages (9)
∗DIN is only available.
2.9-39
2.9-40

Similar documents

Lastenheft Mechanik für die Fertigungen Motor, Getriebe

Lastenheft Mechanik für die Fertigungen Motor, Getriebe Sub-busses are not permitted! Service units: Pressure monitoring by means of a pressure switch must be included in the service unit. For this purpose, an enabled electronic pressure switch accordin...

More information

POWER MODULE

POWER MODULE Mitsubishi Electric power modules are at the forefront of the latest energy innovations that seek to solve global environmental issues while creating a more affluent and comfortable society for all...

More information

Die BUCHSTAVIER - Das Dosierte Leben

Die BUCHSTAVIER - Das Dosierte Leben DAS Dosierte Leben erscheint dann und wann. Herausgeber und Redaktion: Jochen König und Ulrich Balbach. Internet: Werner Rabus (inkl. geordnete Lieferung der Buchstabenkombinationen für diese Ausga...

More information

Series SQ1000/2000

Series SQ1000/2000 nos. of the solenoid valve, etc. Enter in order starting from the first station on the D side. Add the valve and option part number under the manifold base part number. In case of a complex arrange...

More information