DS00511B-0 ICS Install-Setup.indd

Transcription

ICS
INSTALLATION
AND SETUP GUIDE
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ICS PRODUCTS OVERVIEW; FEATURES AND BENEFITS
GXR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Source Card Modules
IM-iPOD . . . . . . . . . . . .
TM-XM . . . . . . . . . . . . .
TM-SIRIUS . . . . . . . . . . .
TM-AM/FM . . . . . . . . . .
IM-AUDIO . . . . . . . . . . .
TM-HD/R. . . . . . . . . . . .
IM-SERVER . . . . . . . . . .
RS232G . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.6
.7
.8
.9
10
11
12
22
User Interface Controls
CONTACT. . . . . . . . . . . . .
iREMOTE® . . . . . . . . . . . . .
DISPLAY . . . . . . . . . . . . . .
SINGLE. . . . . . . . . . . . . . .
IntelliFile ® 3 . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
13
15
17
19
21
GETTING STARTED
Filling Out the GXR2 Installation Worksheet . .
Locating the MAC ID’s . . . . . . . . . . . . . . . .
Installing the Master Key Labels . . . . . . . . . .
Installing and Charging the iREMOTE Battery .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
24
25
26
EXAMPLES OF ICS SYSTEM CONFIGURATIONS
Basic Six-Zone ICS System . . . . . . .
Expanded 12-Zone ICS System . . . .
Expanded 18-30-Zone ICS System .
IM-iPOD Installation Instructions . . .
TM-XM Installation Instructions . . . .
TM-SIRIUS Installation Instructions . .
TM-AM/FM Installation Instructions .
IM-AUDIO Installation Instructions. .
TM-HD/R Installation Instructions . .
IM-SERVER Installation Instructions .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Phone/Paging System Integration . . . . . . . . . . . . . . 50
Home Theater Integration . . . . . . . . . . . . . . . . . . . 51
Linking Multiple Zones . . . . . . . . . . . . . . . . . . . . . 52
CONFIGURING THE GXR2
Selecting a Placement Site for the GXR2 . . . . . . . . . 53
Installing Rack Ears . . . . . . . . . . . . . . . . . . . . . . . . 53
Installing Source Card Modules . . . . . . . . . . . . . . . 53
CONFIGURING AND INSTALLING USER INTERFACE
CONTROLS
Terminating CAT-5 Cables . . . . .
Installing An External IR Sensor .
Connecting IR Sensors . . . . . . .
Installing User Interface Controls
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
54
54
54
55
OPERATING THE SYSTEM
System Settings
CONTACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
DISPLAY and iREMOTE . . . . . . . . . . . . . . . . . . . . . 59
Installer Settings
CONTACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
iREMOTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SPECIFICATIONS
GXR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 27
. 28
. 29
. 30
. 31
. 33
. 35
. 36
. 38
. 40
User Interfaces
ZIGBEE™ Networks . . . . . . . . . . . . . . . . . .
CAT-5 Connection . . . . . . . . . . . . . . . . . . .
IR Sensor Connection . . . . . . . . . . . . . . . . .
Volume Controls . . . . . . . . . . . . . . . . . . . . .
Expanding a Zone with an External Amplifier .
Doorbell Interface Integration. . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 42
. 45
. 46
. 47
. 48
. 49
Source Card Modules
IM-iPOD . . . . . . . . . . . .
TM-XM . . . . . . . . . . . .
TM-SIRIUS . . . . . . . . . .
TM-AM/FM . . . . . . . . .
IM-AUDIO . . . . . . . . . . .
TM-HD/R . . . . . . . . . . .
IM-SERVER . . . . . . . . . .
RS232G . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 65
. 65
. 66
. 66
. 66
. 67
. 67
. 67
User Interface Controls
SINGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
CONTACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
WARRANTY INFORMATION. . . . . . . . . . . . . . . . . . 69
CUSTOMER SERVICE/TECHNICAL SUPPORT . . . . . . 70
(800) BUY-HIFI NILES AUDIO CORPORATION
2
We l c o m e t o N i l e s I n t e l l i C o n t r o l ® I C S
JOIN THE REVOLUTION
A REVOLUTIONARY WHOLE-HOUSE DISTRIBUTED AUDIO SYSTEM
For over a quarter centur y, Niles Audio
Moreover, you’ll be impressed with how
Corporation
designer/
simple it is to install and configure the entire
installers like you with innovative solutions
suite of IntelliControl ICS products with our
that fulfill your clients’ needs and deliver
wizard-based IntelliFile ® 3 software. All of
value to your business. Now we are doing
which means that you can continue to count on
it again by introducing the first modular
Niles when it comes to delivering the innovative
multi zone system that provides you with
solutions that build your reputation and
has
supplied
TM
all the popular sources like HD Radio ,
the profit margins that enable your business
XM
to grow.
®
and Sirius
®
satellite radio, an iPod
®
interface, an AM/FM tuner, media ser ver
and player integration and legacy audio
source interface. With a wide variety of user
interfaces (including: keypads, touch screens,
and the unique iRemote ® hand held 2-way
wireless RF system control remote – all with
complete metadata for ideal user feedback),
Frank K. Sterns
your customers will be amazed at just how
President
easy it is to enjoy their favorite program
material and to control it all at a glance.
3
INTELLICONTROL® ICS PRODUCTS OVERVIEW
GXR2
MODULAR MULTIZONE RECEIVER
System Power
On/Off
Home Theater Integration Ports
Enable audio and video source components
shared with the home theater system to be turned
on, controlled via IR and turned off as needed
Removable Speaker Connectors
Six connectors hold up to
12-gauge speaker wire
TM-AM/FM
FM
ANT
Niles Audio Corporation Miami Florida, USA
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
Integrated Six Slot Card Cage
Accepts any combination of up to six
IntelliControl® ICS integration modules
System Expansion Port
Expandable up to 30 zones
with additional GXR2s
Communication
Control Hub
All user interfaces and GXR2
slave chassis are connected
to any available RJ45 port
Selectable Fixed/Variable
Zone Preamp Outputs
With 12 Volt Triggers for
external amplifier applications
4
GXR2
(CONTINUED)
The IntelliControl ® ICS GXR2 Modular Multizone
Receiver works as the main system distribution center
for IntelliControl ICS. This receiver uses module cards
and distributes the audio and metadata throughout
6 zones, as well as receives controls from our user
interfaces such as the iRemote ® RF remote control with
LCD display, the Contact Touch Screen Control Keypad,
the Display System Control Keypad with LCD display
and the Single Wall Mount Control Keypad.
CONTENTS OF BOX
• 1 IntelliControl ICS GXR2 Modular Multizone Receiver
• 2 Rack Mount Panels
• Speaker Connectors (removable)
• Power Cord
• Quick Install Guide
• Ferrite Beads-4
• GXR2 Installation Worksheet
• Ferrite Bead Notice
FEATURES AND BENEFITS
• Modular MultiZone Receiver
Distributes up to six sources to six zones
• Built-in High Current 12-channel Amplifier
Delivers 55 watts per channel RMS @ 8 ohm and
85 watts per channel @ 4 ohm to each of six zones
• Balance Control
Fine tunes channel levels in each separate zone
• Programmable Turn-On Volume
for each zone
• Alarm Clock and Sleep Timer
for each zone
• Paging/Doorbell Input
Enables system wide voice announcements from a
phone system or doorbell sounds from the Niles DBI-1
• Zone Linking
Allows a grouping of zones to be controlled as
a single zone. Turn-on, source selection, paging
and turn-off all work in unison, yet each zone has
independent volume adjustment and muting
• Home Theater Integration Ports
Enable audio and video source components shared
with the home theater system to be turned on,
controlled via IR and turned off as needed
• Source Matching Gain Control
Ensures changing sources doesn’t require changing
volume control settings
• Selectable Fixed/Variable Zone
Preamp Outputs
With 12 volt triggers for external amplifier
applications
• Removable Speaker Connectors
Hold up to 12-gauge speaker wire
• Plug and Play Integration
IntelliControl ICS integration modules
• Expandable Up to 30 Zones
With additional GXR2’s
• Reliable “One Touch to Music” Operation
using IntelliControl ICS Touch Screens, Keypads
and remote controls
SPECIFICATIONS
• Party Mode
Turns on all your favorite areas from any keypad
or remote control
Power: 55 watts x 12 channels
• Global Off
Turns off all areas from any keypad or remote control
Power Supply: AC 120V, 60Hz
• Tone Controls
Fine tune bass and treble in each separate zone
Shipping Weight: 54 lbs.
Display: 2” High Resolution backlit display
Frequency Response: 26-20 kHz +/- 3 db
Signal to Noise: > = 85 db
Power Consumption: 1500 watts maximum
Dimensions: 17-3/8” W x 5-3/4” H x 18” D
(including feet)
5
INTERCHANGEABLE SOURCE CARD MODULES
IM-iPOD
APPLE
®
I P O D ® I N T E G R AT I O N M O D U L E
iPod Cable IN
Connects to iPod. Provides
input for iPod music, photos
and metadata. Provides
power and control to iPod,
30-pin connector
Cascade Video OUT
Reserved for future use
Cascade Audio OUT
Left and right line-level
audio outputs provide signal
to multi-chassis IntelliControl
ICS systems and home
theater receivers
The IM-iPOD is an iPod ® interface module that slides
into the card cage on an IntelliControl ® ICS Modular
Multizone Receiver. It provides all the functionality typically associated with operating an iPod; playing music,
playlists, podcasts and audiobooks. In addition, the IMiPOD provides both menu and alpha search of content
by: playlist, artist, album, song, podcast, genre, composer and audiobook. The IM-iPOD Module outputs
metadata (artist, album, track, etc.) on IntelliControl ICS
user interfaces with displays. Multiple IM-iPOD modules
can be used in a single chassis to allow multiple iPods to
be played simultaneously in different zones.
The IM-iPOD module will automatically identify
itself to the IntelliFile ® 3 configuration software
during system configuration and map all appropriate
control functions to all user interfaces
• Single Cable Connection
The IM-iPOD connects to an iPod with the included
30-pin cable. The cable facilitates power, control,
audio and metadata
7*%&0
065
Thumbscrews
Secure IM-iPOD to an
IntelliControl ICS Modular
MultiZone Receiver
$"4$"%&"6%*0
065
• Metadata
Artist, album, and song title information are
displayed on IntelliControl ICS user interfaces
equipped with displays
• Menu Navigation
Album, artist, audiobook, composer, genre,
playlist, podcast and song menus can be searched
from any zone that has a user interface equipped
with a display
• Alphabetic Search
Content can be searched alphabetically for quick
access to media from any user interface equipped
with a display
• Remote Transport Control
User interfaces control play/pause, track,
skip, forward/reverse and shuffle on/off from
remote zones
• Cascade Video Out
In the future, composite video output will allow
viewing photo content on TVs or video displays
• Convenient Thumb Screws
Secure module to chassis card cage without need
for additional tools
6
TM-XM
XM
®
S AT E L L I T E R A D I O T U N E R M O D U L E
50Ω Antenna Terminal
SMA jack used to connect
50Ω XM Satellite Antenna
(available separately)
Thumbscrews
Secure TM-XM to
MultiZone Receiver
Cascade Audio OUT
audio outputs for use in
multiple IntelliControl ICS
chassis systems and home
theater receivers
The TM-XM is an XM ® Satellite Radio module that slides
into the card cage on an IntelliControl ® ICS Modular
MultiZone Receiver. The card outputs Metadata (channel name, channel number, category, artist and track)
on IntelliControl ICS user interfaces with LCD displays. It
has all the functionality of a normal tuner: seek through
stations: access to 20 favorite channels and direct access
to a station by entering the channel number. In addition, the TM-XM provides navigation of content by category and channel guide. Multiple TM-XM modules can
be used in a single chassis to allow different XM channels to be played simultaneously in different zones.
The TM-XM module will automatically identify itself
to the IntelliFile ® 3 configuration software during
system configuration and map all appropriate control
functions to all user interfaces
• Metadata
Category, channel name, channel number, artist
and song information is displayed on IntelliControl
ICS user interfaces with displays
• 20 Favorite Channel Presets
User-defined favorites allow easy access to the most
listened to stations. Favorites are displayed on
user interfaces with displays and are configurable
in either IntelliFile ® 3 or from the user interfaces
with displays
• Add to Favorites
Allows user changes to favorites from user interfaces
with displays
• Direct Access Tuning
Provides direct entry of station channel from user
interfaces with numeric keys
• Program Search by Category
Displays channel lists when searched by program
type (i.e. rock, jazz, classical, traffic & weather, etc)
• Channel Guide
Channel Guide lists all available XM Channels
• Channel Skip/Add
Omit channels from the channel list by designating
them as “skipped.” Channels can be added back
into the list later
• Signal Strength Indicator
Shows strength of station broadcast signal on user
interfaces with displays
7
TM-SIRIUS
SIRIUS
®
S AT E L L I T E R A D I O T U N E R M O D U L E
50Ω Antenna Terminal
SMA jack used to connect
50Ω SIRIUS Satellite Antenna
(available separately)
Thumbscrews
Secure TM-SIRIUS to
MultiZone Receiver
Cascade Audio OUT
multiple IntelliControl ICS
chassis systems and home
theater receivers
The TM-SIRIUS is a Sirius ® Satellite Radio module that
slides into the card cage on an IntelliControl ® ICS Modular MultiZone Receiver. The card outputs Metadata
(channel name, channel number, category, artist and
track) on IntelliControl ICS user interfaces with LCD
displays. It has all the functionality of a normal tuner:
seek through stations; access to 20 favorite channels
and direct access to a station by entering the channel
number. In addition, the TM-SIRIUS provides navigation
of content by category and channel guide. Multiple
TM-SIRIUS modules can be used in a single chassis to
allow different SIRIUS channels to be played simultaneously in different zones.
The TM-SIRIUS module will automatically identify
itself to the IntelliFile® 3 configuration software
during system configuration and map all appropriate
control functions to all user interfaces
• Metadata
Category, channel name, channel number, artist
and song information is displayed on IntelliControl
ICS user interfaces with displays
User-defined favorites allow easy access to the most
listened to stations. Favorites are displayed on
user interfaces with displays and are configurable
in either IntelliFile ® 3 or from the user interfaces
with displays
Allows user changes to favorites from user interfaces
with displays
Provides direct entry of station channel from user
interfaces with numeric keys
• Program Search by Category
Displays channel lists when searched by genre
(i.e. rock, jazz, classical, country, news, sports,
traffic, etc)
• Channel Guide
Channel Guide lists all the available SIRIUS Channels
• Channel Skip/Add
Omit channels from the channel list by designating
them as “skipped.” Channels can be added back
into the list later
• Signal Strength Indicator
Shows the strength of the station broadcast signal
on user interfaces with displays
8
TM-AM/FM
AM/FM RADIO TUNER MODULE
FM Antenna Terminal
Connects to included FM
dipole antenna
F-Type terminal
The TM-AM/FM is a tuner module that slides into the
card cage on an IntelliControl ICS Modular Multizone
®
Receiver. It provides the functionality of a normal tuner:
seek through stations, access to 20 favorites and direct
access to a station by entering the channel frequency.
The TM-AM/FM Module outputs metadata (channel frequency) on IntelliControl ICS user interfaces with displays. Multiple TM-AM/FM Tuner Modules can be used
in a single chassis to allow multiple AM/FM channels
to be played simultaneously in different zones.
The TM-AM/FM module will automatically
identify itself to the IntelliFile ® 3 Programming
Software during system configuration and map all
appropriate control functions to all user interfaces
/JMFT"VEJP$PSQPSBUJPO.JBNJ'MPSJEB64"
Cascade Audio OUT
Left and right line-level audio
outputs for use in multi-chassis
IntelliControl ICS systems and
home theater receivers
5.".'.
AM Antenna Terminal
Connects to included AM
loop antenna
'.
"/5
".
"/5
Thumbscrews
Secure TM-AM/FM to
MultiZone Receiver
$"4$"%&"6%*0
065
-
3
User-defined favorites allow easy access to
most listened-to stations. Favorites are displayed
on user interfaces with LCDs and are configurable
in either IntelliFile ® 3 or from user interfaces with
LCD displays
Allows user changes to favorites from user
interfaces with LCD displays
Direct entry of station frequency from user
interfaces with alphanumeric keys
Secure module to chassis card cage without the
need for additional tools
• Metadata
The TM-AM/FM module outputs station frequency
and band (AM or FM) that is displayed on
IntelliControl ICS user interfaces with LCDs
providing real-time tuner status in remote rooms
9
IM-AUDIO
L E G A C Y A U D I O I N T E G R AT I O N M O D U L E
Voltage Sync Input
Connects to the 12V DC system
component or sensing device such
as a Niles CS-12V, LS-1 or any
external 3-30V DC control voltage to
determine when the component is ON
or OFF
IR IN
Connects to the IR OUT on an IMAUDIO in the previous Slave Chassis in
an expanded system (3.5mm mini jack,
Polarity: Tip=+12V; Sleeve=GND)
Audio IN
Connects to the Left and Right audio
outputs on the source component
connected to the IM-AUDIO
The IM-AUDIO is an audio interface module that slides
into the card cage on an IntelliControl
®
ICS Modu-
lar MultiZone Receiver. It provides the connection and
control of a legacy audio source component such as a
CD/DVD player, VCR, cable box or satellite receiver.
Source components are controlled with an IR Flasher
output. 12-Volt and video sensing keep source components in sync with the system when separate IR ON/
OFF codes are not available. The card has memory
to store 20 “Favorites” for tuners, satellite and cable
systems. Cascade audio and IR pass-through allow
expansion to additional IntelliControl ICS Modular
MultiZone Receivers in expanded systems.
The IM-AUDIO module automatically identifies
itself to the IntelliFile® 3 configuration software
during system configuration and maps all
appropriate control functions to all user interfaces
Video Sync Input
Connects to the composite video out of
the source component connected to the
IM-AUDIO. Input senses the presence of
NTSC video sync to determine when the
component is ON or OFF
IR Out
Connects to an IR flasher to send
IR control codes to the source
component connected to the IMAUDIO Module
Cascade Audio OUT
Left and right line-level audio outputs
for use in multiple chassis ICS
systems and home theater receivers
Thumbscrews
Secure IM-AUDIO to IntelliControl ICS
MultiZone Receiver
• Audio Input
Line-level audio output takes the audio output of
a legacy source and distributes it through the
IntelliControl ICS Modular MultiZone Receiver,
then audio is distributed through the zonematix
when selected by a single or a group of zones
• Cascade Audio
Left and right line-level audio outputs for use in
multiple chassis IntelliControl ICS systems and
• IR In
Accepts IR commands from corresponding IMAUDIO modules in slave chassis when multiple
chassis are used in expanded systems
• 3-30 Volt Sync
Detects the ON/OFF state of the connected source
for system power management when used with a
Niles CS-12V Current Sensor for other device
• Video Sync
Detects the ON/OFF state of the connected
source for system power management of source
components using composite video output
10
TM-HD/R
HD RADIO™ TUNER MODULE
FM Antenna Terminal
Connects a 75 ohm FM
antenna
5.)%3
'.
"/5
Cascade Audio OUT
Left and right line-level audio
outputs for use in multi-chassis
IntelliControl ICS systems and
The TM-HD/R is a tuner module that slides into the
card cage on a IntelliControl ICS Modular Multizone
®
Receiver. It provides the functionality of a normal
tuner: seek through stations, access to 20 favorites
and direct access to a station by entering the channel
frequency. In addition, the TM-HD/R provides the
ability to receive an HD Radio ™ broadcast. The TMHD/R Module outputs metadata (channel name, artist
name and song title) on IntelliControl ICS user interfaces
with displays. Multiple TM-HD/R Tuner Modules can
be used in a single chassis to allow multiple AM/FMHD channels to be played simultaneously in different
zones.
The TM-HD/R module will automatically identify
itself to the IntelliFile ® 3 Programming Software
during system configuration and map all
appropriate control functions to all user interfaces.
AM Antenna Terminal
Connects to included AM
loop antenna. Spring clip
Thumbscrews
Secure TM-HD/R to
MultiZone Receiver
".
"/5
$"4$"%&"6%*0
065
-
3
• Metadata
The TM-HD/R module outputs metadata that is
displayed on IntelliControl ICS user interfaces with
LCDs providing real-time information in remote rooms.
When tuning non-HD stations the metadata will
consist of station frequency and band (AM or FM).
A HD radio station can provide additional metadata
such as channel name, artist name and song title.
User-defined favorites allow easy access to
frequently listened-to stations. Favorites are
displayed on user interfaces with LCDs and are
configurable in either IntelliFile ® 3 or from user
interfaces with LCD displays.
Allows user changes to favorites from user
interfaces with LCD displays
Direct entry of station frequency from user
interfaces with alphanumeric keys.
Secure module to chassis card cage without the
need for additional tools.
11
IM-SERVER
M E D I A S E R V E R / P L AY E R I N T E G R AT I O N M O D U L E
Network Device
Connects via CAT 5 to the
Ethernet switch/hub that the
Media Server is connected to.
The IM-Server is an interface module for media
servers and players and slides into the card cage on
an IntelliControl ICS Modular MultiZone Receiver.
It provides Ethernet based control, metadata such
as artist and song title, information to keypads that
have a visual display, and line level audio inputs for
single or multi-stream media servers/players. Source
components are controlled with both an IR flasher
output and CAT 5 Ethernet connections. The card has
cascade audio outputs and IR pass-through to allow
expansion to additional IntelliControl ICS Modular
MultiZone Receivers in expanded systems. Additional
IM-Server cards can be used, one for each stream
output of a multi-steam media server/player.
The IM-SERVER module will automatically
identify itself to the IntelliFile ® 3 Configuration
Software during system configuration and map all
appropriate control functions to all user interfaces.
Audio IN
Connects to the Left and
Right audio outputs on
the Media Server
IR Out
Connects an IR flasher to send
IR control codes to the source
component connected to the
IM-SERVER Module
*.4&37&3
IR IN
Connects to the IR OUT
of an IM-AUDIO card in
the previous Slave Chassis
of an expanded system
(3.5mm mini jack, Polarity:
Tip=+12V; Sleeve=GND)
/&5803,
%&7*$&
*3065
*3*/
-
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
Cascade Audio OUT
multiple chassis ICS systems
and home theater receivers
Thumbscrews
Secure IM-SERVER
to IntelliControl ICS
MultiZone Receiver
• Metadata
Metadata from the media server/player is
displayed on the keypad (that have displays),
touchscreens and iRemote. Metadata depends on
the Media Server’s capabilities and id3 tags on
the music in the library.
• Audio Input
Line-level audio input takes the audio output of a
media server/player source and distributes it through
the IntelliControl ICS Modular MultiZone Receiver,
then audio is distributed through the zone matrix
when selected by a single or a group of zones.
• Cascade Audio
Left and right line-level audio outputs for use in
multiple chassis IntelliControl ICS systems and
home theater receivers.
• IR In
Accepts IR commands from corresponding
IM-AUDIO Modules in slave chassis when multiple
chassis are used in expanded systems.
• IR Out
Outputs IR commands when the media server/
player’s remote is used in zones where a keypad is
using an IR Sensor.
12
USER INTERFACE CONTROLS
CONTACT
S Y S T E M C O N T R O L K E Y PA D W I T H C O L O R T O U C H S C R E E N
Display Screen
High resolution color touch screen
displays system information from iPod,
XM, SIRIUS and AM/FM and functions
associated with “Soft Keys”
Master Keys
8 touch screen buttons provide
“One Touch to Music”
Soft Keys
3 Soft Keys that change
function depending
upon source selected
and control mode
Numeric Keys
Provide direct access
tuning, numeric selection
of track and alphabetic
search for iPod
MUTE
Backlit button
mutes/un-mutes audio
output to zone
OFF
Backlit key turns zone
or system off
PREV/NEXT
2 backlit buttons default
to Next or Previous/
Track or Channel
Niles System Settings
Provides access to system settings:
audio (bass, treble, balance),
sleep timer, alarm clock, etc.
VOL–/VOL+
2 backlit keys adjust
volume UP/DOWN
The IntelliControl ® ICS Contact touch screen is a high
provide additional control for frequently used system and
resolution wall mounted color touch screen user interface.
source commands. The touch screen displays controls,
Eight graphic master key buttons provide Niles’ exclusive
important system information, setup menus and metadata
“One Touch to Music,” which turns the system on, selects
from the IntelliControl ICS Modules.
a source and starts the music. Seven backlit Hard Keys
13
CONTACT
CONTENTS OF BOX
• 1, Contact Touch Screen
• 1, User Guide
• 1, Quick Install Guide
• Eight Customizable Master Key Buttons
Provide “One Touch to Music”
Each of the 8 Master Key buttons can be labeled to
identify the specific source, or music genre that will
be selected when that button is touched. The Master
Key sequences turn on the zone, select the source
and play your favorite channel or music selection
• High Resolution Color Touch Screen
Display with LED Backlighting
The back-lit color LCD displays complete metadata
from IntelliControl ICS sources, zone and system
status, control functions and system setup menus
• Metadata, Preset Favorites and Menus
Metadata (channel frequency, favorite channel
lists, menus and guides) is displayed as provided
by IntelliControl ICS Modules. IntelliControl
ICS Modular MultiZone Receiver system setup
settings can be displayed for configuration of tone
controls, clocks, timers and other system functions
• Pre-defined Control Screens
The graphic control screens used in the Contact
touch screen are pre-defined by the source. During
IntelliFile 3 setup, as the sources are identified, the
control screens are automatically configured and
loaded to the touch screen controllers
• Seven Backlit Hard Keys
These 7 backlit buttons provide convenient access
to frequently used system controls including: Off,
Previous/Next, Volume Up/Down, Mute and the
Niles Logo Button for access to system settings
(CONTINUED)
• Party Mode
Party Mode turns on all your enabled “Party
Zones,” with the push of a button, from anywhere
in your home. Press and hold a Master Key for two
seconds to turn on zones enabled for “Party Mode”
• Source/Zone ON Indicator
The Master Key for the source selected illuminates
to indicate source selected and zone on status
• Zone OFF
Press the OFF Key to turn off the zone you’re
controlling
• Global OFF
Press and hold the OFF key to turn off all zones
from anywhere in the house
• Connects to the IntelliControl ICS Modular
MultiZone Receiver via CAT-5
Connects via CAT-5 data cable terminated with
RJ-45 connectors
• External IR Sensor Input (RJ-45)
RJ-45 jack allows connection of an external IR
sensor to the touch screen for use of an IR remote
in a zone or sub-zone
• Color Options
Faceplates available in three designer colors:
Black, almond and bone
SPECIFICATIONS
Agency Certifications: Class 2/SELV
covering US, Canadian and EU markets
Display: 3.5’ High Resolution color LCD
with LED backlighting.
Warranty: Two year limited
• Built-in IR Sensor
A sensor, located behind the Niles Logo button, allows
use of an IR Remote with the IntelliControl ICS System
DIMENSIONS
• Convenient Backlighting for All Keys
Automatically illuminate when any button is touched
Retrofit wall cutout: 5” W x 4-1/4” H
Includes retrofit installation mounting system
Touch Screen: 5-3/4” W x 5-1/16” H x 2-1/2” D
14
iREMOTE ®
T W O WAY W I R E L E S S R F S Y S T E M C O N T R O L R E M O T E W I T H L C D D I S P L AY
The IntelliControl ® ICS iRemote is a two-way RF (Radio
The High Resolution LCD displays metadata, setup menus
Frequency) hand-held remote control user interface.
and important system information from the Niles Modules.
Eight backlit Master Keys provide Niles exclu-
The iRemote includes a Master Charging Base that
sive “One Touch to Music,” which turns the
recharges the battery and communicates with an
system on, selects a source and starts the music.
IntelliControl ICS Modular MultiZone Receiver to
Additional backlit Hard Keys and Soft Keys
provide system status updates from any zone.
provide complete source and system control.
Master Keys
8 backlit buttons provide
Soft Keys
3 backlit buttons
that change function
depending upon the
source selected
Battery Indicator
Display – Backlit
LCD displays system
information from
Modules and functions
associated with “Soft
Keys”
VOL+/VOL–
2 backlit buttons adjust
volume up or down
PREV/NEXT
2 backlit buttons move to
Next or Previous/Track
or Station
Cursor Keys
and Select Key
navigation of menus,
playlists and favorites
Alphanumeric Keys
Provide direct access
tuning, numeric selection
of track and alphabetic
search for iPod
OFF
Backlit button turns zone
or system off
12V DC
Power Supply
MUTE
Backlit button mutes/
un-mutes audio output
to zone
Provides access to system
settings: audio (bass,
treble, balance), sleep
timer, alarm clock, etc.
Charging Base
CAT-5 Cable
15
iREMOTE ®
CONTENTS OF BOX
• 1, iRemote Handheld Remote Control
• 1, Nickel Hydride Rechargeable Battery
• 1, iRemote Charging Base
• 1, 12Volt Power Supply
• 10, Master Key Caps
• 1, Master Key Label Sheet
• 1, User Guide
Note: The battery is shipped with a minimum charge.
It is important to charge the battery overnight to reach
maximum charge before initial use.
(CONTINUED)
Metadata (channel frequency, favorite channel
lists, menus and guides) are displayed as provided
by the IntelliControl ICS Modules. IntelliControl
ICS Modular MultiZone Receiver system settings
can be displayed for configuration of tone
controls, clocks, timers and other system functions
• Three Soft Keys
These 3 buttons located directly under the LCD,
provide a wide range of controls that change with
each selected source
• Cursor Navigation Keys
Up, Down, Left, Right and Select buttons allow
navigation and selection of options through menus,
lists and guides
• Alphanumeric Keys
Provide direct access tuning, numeric selection
of track and alpha search for media
• Two-Way Wireless Communication
The iRemote transmits commands to a Master
Charging Base, connected to the IntelliControl ICS
Modular MultiZone Receiver for system and source
control. The iRemote Base/Charger receives
system and source status information and metadata
from the Master Charging Base as provided from
the IntelliControl ICS Modular MultiZone Receiver
• Convenient backlighting for all keys
The iRemote is equipped with a motion sensor that
illuminates the keys when it is moved
• Eight Customizable, Backlit Master Keys
Each of the 8 Master Keys can be customized to
identify the specific source or music genre that
will be selected when that button is pressed. The
Master Keys turn the zone on, select a source, and
play your favorite channel or music selection
• Source/Zone On Indicator
• High Resolution LCD Display with LED
Backlighting
The high resolution LCD displays complete
metadata from IntelliControl ICS sources, zone and
system status, “Soft Key” control functions, and
system setup menus
• Zone Off
Press the OFF key to turn off the zone you’re
controlling
• Party Mode
• Mute On Indicator
“Zone Muted” will appear in the title bar of the
iRemote display to indicate the selected zone is muted
• Global Off
Press and hold the OFF key for 2 seconds to turn
off all zones from anywhere in the house
16
DISPLAY
S Y S T E M C O N T R O L K E Y PA D W I T H L C D D I S P L AY
Display
Backlit LCD displays system
information from Modules and
functions associated with “Soft
Keys”.
Master Keys
Soft Keys
3 backlit buttons that
change function depending
upon the source selected
Alphanumeric Keys
Provide direct access tuning,
numeric selection of track and
alphabetic search for iPod
Cursor Keys
navigation of menus, playlists
and favorites
Display Key
Turns on Backlight and LCD
display screen and buttons
MUTE
Backlit button mutes/unmutes audio output to zone
OFF
Backlit button turns zone
or system off
PREV/NEXT
2 backlit buttons move to Next
or Previous/Track or Channel
Provide access to system settings:
audio (bass, treble, balance),
sleep timer, alarm clock, etc.
VOL–/VOL+
volume up or down
The IntelliControl ® ICS Display Keypad is a wall
lit hard keys and soft keys provide complete source
mounted system control keypad with LCD display.
and system control. The High Resolution LCD displays
Eight backlit master keys provide Niles exclusive “One
metadata, setup menus and important system informa-
Touch to Music”, which turns the system on, selects a
tion from IntelliControl ICS Modules.
source and starts the music playing. Additional back-
17
DISPLAY
CONTENTS OF BOX
• 1, Display Keypad
• 1, User Guide
Each of the 8 Master Keys can be customized to
identify the specific source or music genre that
will be selected when that button is pressed. The
Master Keys turn the zone on, select a source, and
play your favorite channel or music selection
• High Resolution LCD Display with LED
Backlighting
The high-resolution LCD displays complete
metadata from IntelliControl ICS sources, zone
and system status, “Soft Key” control functions,
and system setup menus
Metadata, (channel frequency, favorite channel
lists, menus and guides) are displayed as provided
by IntelliControl ICS Modules. IntelliControl ICS
Modular MultiZone Receiver system settings can
be displayed for configuration of tone controls,
clocks, timers and other system functions
• Seven Backlit Hard Keys
These 7 backlit buttons provide convenient access
to frequently used system controls including: Off,
Previous/Next, Volume Up/Down and Mute. The
Niles Logo Button provides access to system settings.
• Cursor Navigation Keys
Up, Down, Left, Right and Select buttons allow
navigation and selection of options through menus,
lists and guides
(CONTINUED)
• Party Mode
• Source/Zone ON Indicator
• Mute ON indicator
The Mute button illuminates red to indicate mute
on. Red illumination turns off when un-muted
• Zone OFF
Press the OFF key to turn off the zone you’re
controlling
• Global OFF
Press and hold the OFF button for 2 seconds to
turn off all zones from anywhere in the house
• Connects to the IntelliControl ICS Modular
The IntelliControl ICS Display Keypad connects to the
IntelliControl ICS Modular MultiZone Receiver via a
CAT-5 data cable terminated with RJ-45 connectors
The RJ-45 jack allows connection of an external IR
sensor to the keypad for use of an IR remote in a
zone or sub-zone
• Optional Display Color Faceplates
Faceplates are available in three designer colors:
Black, Almond and Bone
SPECIFICATIONS
Agency Certifications: Class 2/SELV
covering US, Canadian and EU markets
DIMENSIONS
• Alphanumeric keys
Provide direct access tuning, numeric selection of
track and alpha search for media
Keypad: 5-3/4” W x 5-1/16” H x 2-1/2” D
(based on mounting into 1⁄2” drywall)
Automatically illuminate when any button is pressed
Display: 2” High resolution backlit LCD
Depth behind wall: 5” W x 4-1/4” H
18
SINGLE
WA L L M O U N T S Y S T E M C O N T R O L K E Y PA D
Master Keys
PREV/NEXT
2 backlit buttons move
to Next or Previous /
Track or Channel
OFF
Backlit button turns
zone or system off
–VOL/VOL+
volume UP/DOWN
MUTE
Backlit button mutes/
un-mutes audio output
to zone
The IntelliControl ® ICS Single Keypad is a single-gang,
which turns the system on, selects a source and starts
wall-mounted keypad user interface. Eight backlit Master
the music. Additional backlit Hard Keys provide simple
Keys provide Niles’ exclusive “One Touch to Music”,
system and source control.
19
SINGLE
CONTENTS OF BOX
• 1, Single Keypad
• 1, User Guide
• 4, Decora Inserts (Black, Bone, Almond, White)
Provide “One Touch To Music”
Each of the 8 backlit Master Keys can be
customized to identify the specific source or music
genre that will be selected when that button is
pressed. The Master Keys turn the zone on, select
a source and play your favorite channel or music
selection
• Six Backlit Hard Keys
Provide convenient access to frequently used
system controls. Volume up/down, previous/next
(track/station) mute and off keys provide simple
system and source control
Automatically illuminate when any button is pressed
• Party Mode
(CONTINUED)
• Global Off
Press and hold the OFF key to turn off all zones
from anywhere in the house
• Connects to IntelliControl ICS Modular
The IntelliControl ICS Single Keypad connects
to the IntelliControl ICS Modular MultiZone
Receiver via a CAT-5 data cable terminated with
RJ-45 connectors
RJ-45 jack allows connection of an external IR
sensor to the keypad for use of an IR remote in a
zone or sub-zone
• Fits Standard 1-Gang Box
Installs in standard 1-Gang low voltage box
• Color Inserts
White, almond, bone and black Decora snap-in
color inserts are included
SPECIFICATIONS
Master Keys: 8 Programmable, configurable,
backlit
Hard Keys: 6, backlit
Colors: Almond, black, bone, and white Decora
style inserts
Agency Certifications: Class 2/SELV covering US,
Canadian and EU markets
Shipping Weight: 1 lb.
Warranty: Two-year limited.
• Source/Zone On Indicator
Selected Source Master Key illuminates to indicate
source selected and Zone On status
DIMENSIONS
• Mute On Indicator
Mute button illuminates red to indicate mute on.
Red illumination turns off when un-muted
Depth behind wall: 1-1/8”
(based on mounting into 1/2” drywall)
Keypad: 1-3/4” W x 4” H x 1-5/8” D
20
IntelliFile ® 3
C O N F I G U R AT I O N S O F T WA R E A N D C A P T U R E S TAT I O N
The IntelliFile 3 is designed for use with the IntelliControl® ICS System.
IntelliFile 3 Main Menu screen
LED Status Lights
IntelliFile 3 IR Library screen
Only plug the PC
CAT-5 cable into this
programmer port.
(93.BTUFS$IBTTJT
-&"3/*/(
4&/403
3&"%:
*3
64#
$0//&$51$'03
130(3"..*/(
(93
Front
Connect USB Cable here (from computer)
CAT-5
Cable
*/5&--*'*-&
64#
*3
'-"4)&3
065
* / ' 3 " 3 & % $ " 1 5 6 3 & 4 5 " 5 * 0 /
*35&45
065165
USB
Cable
Back
IntelliFile 3 IR Capture Station
CONTENTS OF BOX
Note: This system requires a computer
with either Windows XP Professional or
Vista operating system, at least 256MB
RAM, 100MB free HD space, 1024 x 768
display, CD-ROM drive, Ethernet and USB
Port.
• 1, 4 Meter CAT5 Cable
• 1, 2 Meter USB Cable
• 1, IntelliFile 3 Capture Station
• 1, ABS plastic carrying case
21
RS232G
B I - D I R E C T I O N A L G AT E WAY
• Low profile, small footprint for unobtrusive
installation
• Provide bi-directional gateway for an
IntelliControl® ICS system to control and
communicate to subsystems such as media servers
and lighting controls, and allows third-party home
control systems to communicate and control an
IntelliControl® ICS system as its audio subsystem
• Integrated mounting wings accommodate
either vertical or horizontal installation
• Rugged all metal chassis construction
• Self adhesive rubber feet and snap in
“Christmas Tree” plugs included
• Convenient configurable DB9 Cable/terminal
strip connector
SPECIFICATIONS
• Plug and Play integration to Niles
IntelliControl ® ICS systems
Power: 12VDC @ 90mA (powered through
Intellicontrol ICS wiring)
• IntelliFile3 ® Wizard based configuration
Note: IM-Audio card required for integration of audio on a music
server
• All control functions and screens
automatically mapped to ICS user interfaces
• Subsystem compatibility control with
Lutron ®, Escient ®, and Audio Request ®* on
first release
Warranty: Two-year limited.
DIMENSIONS
• Compatibility with AMX, Crestron, and other
RS232 devices as drivers become available
• 5-5/8" wide x 3-1/8" high x .7/8" deep
MUSIC SERVER
Audio Out
L R
IR In
RS232
RS232G
5 5/8"
DB9 CABLE
3 1/8"
CAT-5 CABLE
GXR2
* Single stream audio units only. Multiple
stream models supported using IM-Server
module.
22
GETTING STARTED
FILLING OUT THE GXR2 INSTALLATION WORKSHEET
IMPORTANT: This document is your system design
map. It must be filled out correctly before any
programming or installation occurs.
1
The GXR2 Installation Worksheet, included with the
IntelliControl ® ICS Modular Multizone Receiver (and
available for download at www.IntelliControl.com),
provides spaces for placing the MAC ID stickers next
to the name of the zone they are located in. Take
special care in associating the correct MAC ID sticker
with the right zone on the worksheet.
Remove the MAC ID sticker
from master iRemote base(s)
and place them in the boxes
on the worksheet.
Two MAC ID stickers are found on the iRemote Charging
Base. Remove one of the stickers and place in the area
under the box marked “1” box for the “iRemote
Master Charging Base” on the GXR2 Installation
Worksheet.
DO NOT REMOVE BOTH STICKERS FROM
THE iREMOTE BASE. It may become necessary
to reference the iRemote charging base sticker
for troubleshooting
2
Name each zone
and assign the
user interfaces
Remove the MAC ID sticker
from each user interface and
place next to the zone to
which it has been assigned.
Designate the
iRemote® master
charging bases
iREMOTE MASTER
CHARGING BASE
(NETWORK 1)
M A S T E R
OUTPUT
iREMOTE MASTER
CHARGING BASE
(NETWORK 2)
J3&.05&$
C H A S S I S
Z O N E
NAME
Z O N E
U S E R
MAC ID#
1
Kitchen
4*/(-&$
2
Patio
%*41-":$
3
Master Bd
N A M E S
J3&.05&$
A N D
U S E R
I N T E R F A C E A S S I G N M E N T
MAC ID#
MAC ID#
$0/5"$5$
4
R S232G MODU LE A SS IGNME NTS / M A STE R KEY L AB E L S
3
Assign sources
Enter the names of the source
modules inserted in the card
slots of the master chassis. For
IM-AUDIO/RS232G module(s),
enter the brand, type and model
of the component connected to
it. For RS232G place the MAC
ID in the appropriate space.
Note: Source in Card
Slot 1 must be assigned
to Master Key 1, Card
Slot 2 must be assigned
to Master Key 2, and
so on.
Choose a label for the master
key of each source module
installed.
If one or more of the card
slots are empty, you are free
to assign any Source to the
corresponding Master Key.
CARD
SLOT
SOURCE COMPONENT ASSIGNMENT
MAC ID
34($
34($
BRAND
TYPE
Lutron
grafik eye
MODULE
MASTER KEY
N o.
LABEL
lights
7
SOURCE MODULE ASSIGNMENT / MASTER KEY LABELS
CARD
SLOT
1
2
3
4
5
6
MASTER KEY
SOURCE COMPONENT ASSIGNMENT
MODULE
TYPE
IM-IPOD
TM-XM
TM-AM/FM
IM-AUDIO
IM-AUDIO
-------
BRAND
TYPE
MODEL
------------------SONY
SONY
------------------DSS
------------------ABC
123
XM
LUTRON
XM
MASTER KEY 1
MASTER KEY 2
iPod
XM
MASTER KEY 3
MASTER KEY 4
AM/FM
DSS
MASTER KEY 5
MASTER KEY 6
CD
Rock
MASTER KEY 7
MASTER KEY 8
LIGHTS
CLASSICAL
CD
N o.
1
2
3
4
5
6
7
8
LABEL
IPOD
XM
AM/FM
DSS
CD
ROCK
LIGHTS
CLASSICAL
23
GETTING STARTED
MEDIA ACCESS CONTROL ADDRESS (MAC ID)
LOCATING THE MAC ID
The Media Access Control Address (MAC ID), tells the
IntelliControl ICS Modular MultiZone Receiver which
device, in this case an iRemote, is sending commands.
The IntelliControl ICS Modular MultiZone Receiver then
knows which zone to turn on and which source to select
for that zone.
MAC ID Sticker
I2%-/4%
0''
13&7
/&95
70-
70-
.65&
#/.4!#4
I2%-/4%
MAC ID Sticker
#/.4!#4
#/.4!#4
#/.4!#4
See the diagrams below for the location of the MAC
IDs for each user interface.
Contact Touch Screen Mac ID sticker location
I2%-/4%
I2%-/4%
MAC ID Sticker
iRemote base,
bottom view.
13&7
/&95
"#$
%&'
()*
+,-
./0
1234
567
89:;
%JTQMBZ
70-
&OUFS
70-
.65&
3).',%
+";;
#-6&4
$)30,!9
30$,
$-"44*$"-
$)30,!9
0''
9.
".'.
$)30,!9
4&-&$5
J10%
4*3*64
$)30,!9
MAC ID Sticker
3).',%
3).',%
3).',%
iRemote Mac ID sticker location
Single Keypad Mac ID sticker location
Display Keypad Mac ID sticker location
24
GETTING STARTED
INSTALLING THE MASTER KEY LABELS
TO INSTALL THE MASTER KEY LABELS (Figure 6):
1. Locate the Master Key keycaps. (Keycaps DO NOT come installed for
the iRemote).
2. Place labels from the included label sheet face down inside the keycap.
3. Place the caps in the appropriate key locations. (Refer to the GXR2 Installation
Worksheet to assure proper position).
Note: Keycaps may need noticeable force to install correctly.
Figure 6.
Step 1: Label sheet removal.
Step 2: Insert label face down in keycap.
Step 3: Place keycap over Master Key and snap into place.
13&7
70-o
0''
iRemote shown.
/&95
70-
.65&
Single Keypad shown.
Display Keypad shown.
25
GETTING STARTED
INSTALLING AND CHARGING
THE iREMOTE ® BATTERY
INSERTING THE BATTERY
DISPLAY SETTINGS (BATTERY SAVE)
The iRemote uses a nickel metal hydride rechargeable
battery that must be fully charged prior to initial use.
Install the battery and allow it to charge for 12 hours,
before initial use.
Press the Niles System Settings
Key. The “System Settings menu”
Press the [Page
System Settings
Display Settings
appears.
Turn On Volume
] Soft Key to move
to the second screen of settings.
Highlight [Display Settings] and
press the SELECT
Key to proceed.
Press the Cursor
Key to move
from [Backlight On] time to [Battery Save].
Use the Cursor
Page
Back
Page
Display Settings
Contrast 65%
Backlight on: 30 sec.
or
Key to set the
length of time until the iREMOTE goes into
Battery save
after 5 minutes
Back
deep sleep mode.
NOTE: Battery Save mode disconnects the iREMOTE from the GXR2
network and doesn’t display metadata until picked up.
CHARGING THE IREMOTE
Your new iRemote comes equipped with a rechargeable battery, charging base and power supply. After
every use, place your iRemote into the charging base
cradle. The charging base’s front panel light changes
from light blue to bright blue when the remote is seated
correctly. When the battery is charging, the LCD display reads “Charging”, and when charging is complete
the display reads “Charging Complete.” The iRemote
operates approximately 8 hours in normal mode or 24
hours in battery save mode.
Power Jack
12V DC
Power Supply
System (CAT-5) connects to IntelliControl ICS Modular MultiZone
Receiver Communication & Control Switch when used as Master
Charging Base
26
EXAMPLES OF INTELLICONTROL® ICS SYSTEM CONFIGURATIONS
BASIC SIX ZONE INTELLICONTROL® ICS SYSTEM
iPod
to 3-30V SYNC IN
Satellite Receiver
To Unswitched
Outlet
CS-12V
IR Flasher
DVD/CD Player
DIGITAL AUDIO OUT
OPTICAL
L
COAXIAL
R
AUDIO OUT
To Left Speaker
TM-AM/FM
AM
ANTENNA
FM
ANTENNA
FM
ANT
To Right Speaker
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
XM
ANTENNA
SIRIUS
ANTENNA
CAT-5
Cable
16/4
Speaker
Wire
ZONE 1
ZONE 2
ZONE 3
Speakers
Speakers
Speakers
ZONE 4
ZONE 5
ZONE 6
Speakers
Speakers
Speakers
Figure 7.
27
EXPANDED 12 ZONE ICS SYSTEM
Expanding the system from six to twelve zones requires
connected from the slave’s System Expansion Port to an
an additional GXR2. Using the Intellifile 3 software, one
available port in the master’s Communication Control
GXR2 is designated as the Master and the second GXR2
Hub. Below is an example of an expanded 12 zone
as Slave 1. The system communicates via a CAT-5 cable
IntelliControl® ICS system.
®
NOTE: It is recommended to have the latest version of the software and drivers that integrate the latest features and revisions. Please
visit our website to download the latest version of IntelliFile 3 Configuration software at http://www.IntelliControl.com/techsupport.
OPTIONAL
AUDIO R
SERIAL
REQUIRED
IR
S-VIDEO
DSS Audio
Out L & R
MF1
Flasher
GXR2
ZONE 4
ZONE 5
ZONE 6
SLOT 6
Page Trigger
8Ω (4Ω min.)
SLOT 5
8Ω (4Ω min.)
SLOT 4
8Ω (4Ω min.)
SLOT 3
ZONE 3
8Ω (4Ω min.)
SLOT 2
ZONE 2
Niles Audio Corporation
Miami Florida, USA
SERIAL NUMBER
8Ω (4Ω min.)
SLOT 1
DSS Video
Out
ZONE 1
Page Input
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
(SAT) OUT
VHF/UHF
CH
3|4
VIDEO
ACCESS CARD
DIGITAL
AUD OUT
8Ω (4Ω min.)
AC~IN
OUTPUT
CNTRL
OUT
TEL LINE
AUDIO L
SATELLITE IN
1
2
DSS RECEIVER
IR Output
VIDEO
SYNC
IN
3-30V
SYNC
IN
R
12V Control
Out 150mA
R
AUDIO
IN
12V Control
Out 150mA
CLASS II WIRING
R
L
12V Control
Out 150mA
Out to Master
1
2
3
4
5
6
7
8
9
10
11
12
R
12V Control
Out 150mA
120 Volts ~ 60Hz. 500 Watts Max.
COMMUNICATION
& CONTROL HUB
MAC ADDRESS
GXR2
Designed and Engineered in the USA. Made in Malaysia.
Slave1
to Master
CAT-5 Cable
ZONE 1
Page Input
ZONE 2
Zones 1 Through 6
ZONE 3
ZONE 4
ZONE 5
ZONE 6
Miami Florida, USA
SLOT 5
SLOT 6
Page Trigger
8Ω (4Ω min.)
SERIAL NUMBER
SLOT 4
L
12V Control
Out 150mA
EXPANSION
Cascade
IR In/Out
SLOT 3
12V Control
Out 150mA
L
R
CASCADE AUDIO
OUT
Cascade
Audio Out
L&R
SLOT 2
CLASS II WIRING
R
DoubleInsulated
When servicing use only
identicalreplacementparts.
DSS
SLOT 1
L
CAUTION: Refer to the operations guide for less than 8W installations.
IM-AUDIO
CLASS II WIRING
R
8Ω (4Ω min.)
L
R
L
Master Chassis
HT Sync
L
GXR2
CLASS II WIRING
R
8Ω (4Ω min.)
L
L
8Ω (4Ω min.)
R
CLASS II WIRING
R
IR OUT
8Ω (4Ω min.)
L
CASCADE AUDIO
OUT
iPod
TM-iPOD
CLASS II WIRING
L
HT IR In
IR IN
8Ω (4Ω min.)
R
Sirius
TM-SIRIUS
CASCADE AUDIO
OUT
ANT
XM
TM-XM
50
12V Control
Out 150mA
IM-AUDIO
IM-iPOD
L
ANT
CASCADE AUDIO
OUT
TM-AM/FM
TM-SIRIUS
TM-XM
IM-MP3
AM/FM
50
iPod
30 Pin
Connector
IR Output
VIDEO
SYNC
IN
3-30V
SYNC
IN
L
R
CASCADE AUDIO
OUT
L
AUDIO
IN
R
L
R
CASCADE AUDIO
OUT
IM-AUDIO
IR OUT
IR IN
L
AUDIO
IN
R
L
R
CASCADE AUDIO
OUT
R
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
AUDIO
IN
IM-AUDIO
IR OUT
IR IN
L
R
CASCADE AUDIO
OUT
L
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
R
IM-AUDIO
IR OUT
IR IN
AUDIO
IN
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
L
IM-AUDIO
IR OUT
IR IN
IM-AUDIO
IM-AUDIO
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
AUDIO
12V Control
Out 150mA
IM-AUDIO
CLASS II WIRING
L
CLASS II WIRING
R
L
L
AUDIO
IN
CLASS II WIRING
R
L
CLASS II WIRING
R
L
R
CLASS II WIRING
L
R
Slave 1 Chassis
IR OUT
HT Sync
L
GXR2
CLASS II WIRING
R
HT IR In
IR IN
12V Control
Out 150mA
R
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
DoubleInsulated
Out to Master
1
2
EXPANSION
7
8
L
R
CASCADE AUDIO
OUT
3
4
5
6
10
11
12
COMMUNICATION
& CONTROL HUB
MAC ADDRESS
IM-Audio Modules
CAT-5
Cable
16/4
Speaker
Wire
ZONE 7
ZONE 8
ZONE 9
ZONE 10
ZONE 11
ZONE 12
28
EXPANDED 18-30 ZONE ICS SYSTEM
The IntelliControl ® ICS system is capable of expanding
Using the IntelliFile ® 3 software, one is designated as the
up to 30 zones. Expanding the system requires daisy-
Master and the rest are designated as Slave 1, Slave
chaining additional GXR2 Modular Multizone Receivers
2, etc. Below is an example of an expanded 18 zone
for each additional 6 zones, up to a maximum of 5 GXR2s.
IntelliControl ICS system.
NOTE: It is recommended to have the latest version of the software and drivers that integrate the latest features and revisions.
Please visit our website to download the latest version of IntelliFile 3 Configuration software at http://www.IntelliControl.com/
techsupport.
OPTIONAL
AUDIO R
DIGITAL
AUD OUT
REQUIRED
IR
S-VIDEO
DSS Audio
Out L & R
MF1
Flasher
GXR2
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
SLOT 6
Page Trigger
8Ω (4Ω min.)
SLOT 5
8Ω (4Ω min.)
SLOT 4
8Ω (4Ω min.)
Miami Florida, USA
SERIAL NUMBER
SLOT 3
8Ω (4Ω min.)
SLOT 2
8Ω (4Ω min.)
SLOT 1
DSS Video
Out
ZONE 1
Page Input
(SAT) OUT
VHF/UHF
CH
3|4
VIDEO
ACCESS CARD
SERIAL
8Ω (4Ω min.)
AC~IN
OUTPUT
CNTRL
OUT
TEL LINE
AUDIO L
SATELLITE IN
1
2
DSS RECEIVER
IR Output
VIDEO
SYNC
IN
3-30V
SYNC
IN
L
R
R
12V Control
Out 150mA
R
AUDIO
IN
12V Control
Out 150mA
CLASS II WIRING
R
L
12V Control
Out 150mA
Out to Master
1
2
3
4
5
6
7
8
9
10
11
12
R
12V Control
Out 150mA
COMMUNICATION
& CONTROL HUB
MAC ADDRESS
GXR2
Slave1
to Master
CAT-5 Cable
ZONE 1
Page Input
ZONE 2
Zones 1 Through 6
ZONE 3
ZONE 4
ZONE 5
ZONE 6
Miami Florida, USA
SLOT 5
SLOT 6
Page Trigger
8Ω (4Ω min.)
SERIAL NUMBER
SLOT 4
L
12V Control
Out 150mA
EXPANSION
Cascade
IR In/Out
SLOT 3
12V Control
Out 150mA
L
R
CASCADE AUDIO
OUT
Cascade
Audio Out
L&R
SLOT 2
CLASS II WIRING
R
DoubleInsulated
DSS
SLOT 1
L
IM-AUDIO
CLASS II WIRING
R
8Ω (4Ω min.)
L
L
Master Chassis
HT Sync
L
GXR2
CLASS II WIRING
R
8Ω (4Ω min.)
R
TM-iPOD
L
8Ω (4Ω min.)
CASCADE AUDIO
OUT
CLASS II WIRING
R
IR OUT
8Ω (4Ω min.)
L
TM-SIRIUS
iPod
CLASS II WIRING
L
HT IR In
IR IN
8Ω (4Ω min.)
R
Sirius
TM-XM
CASCADE AUDIO
OUT
ANT
XM
50
12V Control
Out 150mA
IM-AUDIO
IM-iPOD
L
ANT
CASCADE AUDIO
OUT
TM-AM/FM
TM-SIRIUS
TM-XM
IM-MP3
AM/FM
50
iPod
30 Pin
Connector
IR Output
L
R
CASCADE AUDIO
OUT
L
AUDIO
IN
R
L
R
CASCADE AUDIO
OUT
IM-AUDIO
IR OUT
IR IN
L
AUDIO
IN
R
R
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
AUDIO
IN
IM-AUDIO
IR OUT
IR IN
L
R
CASCADE AUDIO
OUT
L
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
R
IM-AUDIO
IR OUT
IR IN
AUDIO
IN
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
L
IM-AUDIO
IR OUT
IR IN
IM-AUDIO
IM-AUDIO
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
L
R
CASCADE AUDIO
OUT
AUDIO
12V Control
Out 150mA
IM-AUDIO
CLASS II WIRING
L
CLASS II WIRING
R
L
L
AUDIO
IN
CLASS II WIRING
R
L
CLASS II WIRING
R
L
12V Control
Out 150mA
R
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
DoubleInsulated
Out to Master
1
2
EXPANSION
7
8
3
4
5
6
10
11
12
L
R
CASCADE AUDIO
OUT
ZONE 2
Zones 7 Through 12
ZONE 3
ZONE 4
ZONE 5
ZONE 6
Miami Florida, USA
8Ω (4Ω min.)
8Ω (4Ω min.)
Page Trigger
8Ω (4Ω min.)
SLOT 6
8Ω (4Ω min.)
SLOT 5
8Ω (4Ω min.)
SERIAL NUMBER
SLOT 4
Slave 2
to Slave 1
CAT-5 Cable
ZONE 1
Page Input
SLOT 3
12V Control
Out 150mA
Cascade
IR In/Out
GXR2
SLOT 2
R
COMMUNICATION
& CONTROL HUB
Cascade
Audio Out
L&R
SLOT 1
CLASS II WIRING
L
MAC ADDRESS
R
Slave 1 Chassis
IR OUT
HT Sync
L
GXR2
CLASS II WIRING
R
HT IR In
IR IN
8Ω (4Ω min.)
VIDEO
SYNC
IN
3-30V
SYNC
IN
IR Output
VIDEO
SYNC
IN
3-30V
SYNC
IN
L
R
CASCADE AUDIO
OUT
L
AUDIO
IN
R
L
R
CASCADE AUDIO
OUT
IM-AUDIO
IR OUT
IR IN
L
AUDIO
IN
R
L
R
CASCADE AUDIO
OUT
R
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
AUDIO
IN
IM-AUDIO
IR OUT
IR IN
L
R
CASCADE AUDIO
OUT
L
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
R
IM-AUDIO
IR OUT
IR IN
AUDIO
IN
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
IM-AUDIO
L
IM-AUDIO
IR OUT
IR IN
IM-AUDIO
IM-AUDIO
AUDIO
VIDEO
SYNC
IN
3-30V
SYNC
IN
AUDIO
12V Control
Out 150mA
IM-AUDIO
CLASS II WIRING
L
CLASS II WIRING
R
L
L
AUDIO
IN
CLASS II WIRING
R
L
CLASS II WIRING
R
L
R
CLASS II WIRING
L
R
Slave 2 Chassis
IR OUT
HT Sync
L
GXR2
CLASS II WIRING
R
HT IR In
IR IN
12V Control
Out 150mA
R
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
12V Control
Out 150mA
DoubleInsulated
Out to Master
1
2
EXPANSION
7
8
L
R
CASCADE AUDIO
OUT
3
4
5
6
10
11
12
COMMUNICATION
& CONTROL HUB
MAC ADDRESS
IM-Audio Modules
CAT-5
Cable
16/4
Speaker
Wire
ZONE 13
ZONE 14
ZONE 15
ZONE 16
ZONE 17
ZONE 18
29
IM-iPOD INSTALLATION INSTRUCTIONS
INSTALLATION
EXPANDING THE SYSTEM
WARNING: Always turn the power OFF on the Intellicontrol
ICS Modular MultiZone Receiver and be sure the AC line
cord is disconnected to avoid damage and electrical shock
before making any connections to the IM-iPOD Module.
When using multiple chassis, connect the Left & Right
Cascade Audio OUT of the IM-iPOD to the Left & Right
Audio IN on the IM-AUDIO Module in the same number
card slot on the Slave chassis. Up to four Slave chassis
may be used in a system (see Figure 7).
CAUTION: The IM-iPOD Module is susceptible to static
discharge. Be sure to use a grounding strap or touch an
earth ground prior to picking up the IM-iPOD. Handle the
card by its edges.
1. Carefully slide the IMiPOD Module into the
appropriate card slot.
(Refer to the GXR2
Installation Worksheet
to assure proper card
slot number.)
.BTUFS(93
4MBWF(93
*.J10%.PEVMF
*."6%*0.PEVMF
7*%&0
065
$"4$"%&"6%*0
065
Guides
Figure 1. Inserting the Module Card
into the GXR2 Card Cage.
4UFSFP3$"
UP3$"$BCMF
2. Concentrate on the
GXR2 card cage guides as you insert the module card.
3. Be sure the multi-pin connector is secured to the header
in the card cage.
4. Tighten thumbscrews. (Do not over tighten.)
-3$BTDBEF
"VEJP0VU
-3
"VEJP*O
Figure 5. Cascade Audio Connections
Expanded Systems Diagram
Connecting The iPod
The included 30-pin cable connects an iPod to the
IM-iPOD Module. It provides bidirectional transmission
of data, control and power to the
iPod.
J1PE
%PDL$POOFDUPS
QJO$POOFDUPS$BCMF
J1PE
$BCMF*/
1. Connect one end of the included
30-pin cable to the Dock Connector
Port on the bottom edge of the iPod
(see Figure 2).
(93.BTUFS$IBTTJT
7*%&0
065
$"4$"%&"6%*0
065
2. Connect the other end of the
cable to the IM-iPOD Module.
Figure 2. iPod connection
to 30-pin cable connection
on\IM-iPOD Module Card
Figure 3. The IM-iPOD card is ready for use when the Niles logo appears.
$0..6/*$"5*0/
$0/530-48*5$)
*.J10%
.PEVMF
$BTDBEF
"VEJP065
4UFSFP
3$"3$"
$BCMF
$PNNVOJDBUJPO
BOE$POUSPM4XJUDI
$"5$BCMF
iPod
(934MBWF$IBTTJT
J1PE
30-pin Connector Cable
$0..6/*$"5*0/
$0/530-48*5$)
7*%&0
065
$"4$"%&"6%*0
065
*."6%*0
.PEVMF
"VEJP*/
Figure 4. iPOD Connecting to the Module Card.
&YQBOTJPO
065UP.BTUFS
Figure 6. Expanded System with Cascade Audio Connections
30
TM-XM INSTALLATION INSTRUCTIONS
INSTALLATION
WARNING: Always turn power OFF on the IntelliControl
ICS Modular MultiZone Receiver and be sure the AC
line cord is disconnected to avoid damage and electrical shock before making any connections to the TMXM Module.
CAUTION: The TM-XM Module is susceptible to static
discharge. Be sure to use a grounding strap or touch
an earth ground prior to picking up the TM-XM. Handle
the card by its edges.
1. Carefully slide the TM-XM Module into the appropriate card slot. (Refer to the GXR2 Installation Worksheet to assure proper card slot number.)
MULTIPLE TM-XM MODULE
CARDS
When using more than one TM-XM Module Card in an
installation, each tuner must be connected to a satellite
radio antenna. The Niles SRK-2W or SRK-4W B allows
for one antenna to provide proper signal strength to
multiple TM-XM tuner modules. (See Figure 3.)
Niles manufactures a line of satellite radio accessories
that include a satellite radio antenna (ANT-SAT) and
Installation Kits for one Satellite Radio Tuner (SRK-1W).
B (See Figure 2 and 3)
See NilesAudio.com for the complete line of Satellite
Radio Accessories.
2. Concentrate on the GXR2 card cage guides as you
insert the module card.
Figure 2. Installation diagram for one satellite
tuner using the SRK-1W Installation Kit
5.".'.
ANT– SAT*
XM®/SIRIUS® SATELLITE
RADIO ANTENNA
SRK-1W
'.
"/5
A
".
"/5
B
$"4$"%&"6%*0
065
-
3
4-8-ODULE
#ARD
ILA–16dB
IMT–50/75 MF
Guides
COAX CABLE
IMT–75/50
SRC–2M
C
Figure 1. Inserting the module card into the GXR2 card cage
IMT– 50/75 SMB*
3. Be sure the multi-pin connector is secured to the
header in the card cage.
A
CUSTOMER
SUPPLIED
ANTENNA
COAX CABLE
USE WITH UNIVERSAL SATELLITE ANTENNA
F2F
ALTERNATIVE CABLING
*SOLD SEPARATELY
Figure 3. Installation diagram for two satellite
tuners using the SRK-2W Installation Kit
CONNECTING AN ANTENNA TO THE TM-XM
MODULE CARD
When all modules are in place, and the system components have been installed, connect a satellite radio
antenna A to the 50Ω ANT jack on the TM-XM Module Card C .
SRK-2W
ANT– SAT*
XM/SIRIUS SATELLITE
RADIO ANTENNA
B
A
SRS –2W
Note: A Satellite Radio Antenna is not included with
the TM-XM
C
IMT–75/50
ILA–16dB
IMT– 50/75 MF
COAX CABLE
COAX CABLE
IMT–75/50
AIMING THE ANTENNA
Choose a mounting location for the Satellite Radio
Antenna that has a clear and unobstructed view of the
sky. Position the antenna for optimum signal strength in
your area of the country.
4-8-ODULE
#ARD
IMT–50/75 SMB*
A
4-8-ODULE
#ARD
SRC–2M
C
CUSTOMER SUPPLIED
ANTENNA
*SOLD SEPARATELY
31
TM-XM INSTALLATION INSTRUCTIONS
ANTENNA ADJUSTMENT
1. Adjust the XM antenna for signal strength. For best
results, the antenna should be mounted outdoors
with an unobstructed southeast facing. Some directional adjustment will be needed to attain optimum
signal strength. When the antenna is in the optimum
position, the signal strength indicator, located on the
User Interface LCD in the upper left corner, will show
three bars.
(CONTINUED)
When using multiple chassis, connect the Left and Right
Cascade Audio OUT of the TM-XM to the Left and Right
Audio IN on the IM-AUDIO Module in the same number
card slot on the Slave chassis. Up to four Slave chassis
may be used in a system.
.BTUFS(93
4MBWF(93
5.9..PEVMF
*."6%*0.PEVMF
2. To test the TM-XM prior to activation, tune to Channel 1. (XM Preview) If the “Preview Channel” plays,
the tuner is ready for activation.
NOTE: See “Troubleshooting” for additional information regarding on-screen messages.
Stereo
RCA
to
RCA
4UFSFP3$"
UP3$"$BCMF
Cable
ACTIVATION
It is recommended that the homeowner activate the XM
Subscription Service, to make service package choices
and to assure proper subscription and billing information. If providing this service for the homeowner:
1. Have IntelliControl ICS System powered up and
active with TM-XM selected.
2. Tune to Channel 0 to get the XM ID Number. Write
the number down for future reference.
3. Find the 8-character XM Radio ID of the XM Card.
-3
L&R
"VEJP*O
Audio
In
"/54"5
"OUFOOB
5.9.
.PEVMF
5.".'.
4. You can now activate XM by calling 1-800-XM-RADIO
(1-800-967-2346) or on the internet visit http://activate.xmradio.com and have the homeowner’s credit
card and XM Radio ID ready and follow the prompts
to activate your subscription.
-3$BTDBEF
L&R
Cascade
"VEJP0VU
Audio Out
(93.BTUFS$IBTTJT
'.
"/5
7*%&0
065
".
"/5
$"4$"%&"6%*0
065
$"4$"%&"6%*0
065
$0..6/*$"5*0/
$0/530-48*5$)
$BTDBEF
"VEJP0VU
$PNNVOJDBUJPO
BOE$POUSPM4XJUDI
$BU$BCMF
4UFSFP
3$"3$"
$BCMF
(934MBWF$IBTTJT
$0..6/*$"5*0/
$0/530-48*5$)
"VEJP*O
&YQBOTJPO
065UP.BTUFS
*."6%*0
.PEVMF
32
TM-SIRIUS INSTALLATION INSTRUCTIONS
INSTALLATION
AIMING THE ANTENNA
WARNING: Always turn the power OFF on the
Intellicontrol ICS Modular MultiZone Receiver and be
sure the AC line cord is disconnected to avoid damage
and electrical shock before making any connections to
the TM-SIRIUS Module.
Choose a mounting location for the Satellite Radio
Antenna that has a clear and unobstructed view of
the sky. See the SIRIUS Antenna Directional Map for
instructions on positioning the antenna for optimum signal strength in your area of the country.
CAUTION: The TM-SIRIUS Module is susceptible to static
earth ground prior to picking up the TM-SIRIUS. Handle
Figure 3. SIRIUS Antenna Directional Map
5.".'.
1. Carefully slide the TM-SIRIUS Module into the appropriate card slot. (Refer to the GXR2 Installation Worksheet to assure proper
card slot number.)
2. Concentrate on the GXR2
card cage guides as you
3. Be sure the multi-pin
connector is secured
to the header in the
card cage.
'.
"/5
".
"/5
$"4$"%&"6%*0
065
-
3
X
Guides
Figure 1. Inserting the module
card into the GXR2 card cage.
4. Tighten
thumbscrews.
(Do not over tighten)
ANTENNA ADJUSTMENT
CONNECTING AN ANTENNA TO THE TM-XM
MODULE CARD
When all modules are in place, and the system components have been installed, connect a satellite radio
antenna A to the 50Ω ANT jack on the TM-SIRIUS
Module Card C .
Note: A Satellite Radio Antenna is not included with
the TM-SIRIUS
ANT– SAT*
XM®/SIRIUS® SATELLITE
RADIO ANTENNA
SRK-1W
A
4-3)2)53
-ODULE
#ARD
ILA–16dB
IMT–50/75 MF
COAX CABLE
IMT–75/50
SRC–2M
C
CUSTOMER SUPPLIED
ANTENNA
If you are located in...
Area
Area
Area
Area
Area
1:
2:
3:
4:
5:
Point
Point
Point
Point
Point
the
the
the
the
the
ANT-SAT
ANT-SAT
ANT-SAT
ANT-SAT
ANT-SAT
Southeast
Northeast
Northwest
Southwest
Straight Up
Some minor directional adjustment may be needed
to attain optimum signal strength. When the antenna
is in the optimum position, the signal strength indicator, located on the User Interface LCD in the upper
left corner, will show three bars.
2. To test the TM-SIRIUS prior to activation, tune to Channel 184. (The SIRIUS Preview Channel). If the Preview
Channel plays, the tuner is ready for activation.
IMT–50/75 SMB*
A
1. Adjust the SIRIUS antenna for signal strength. For
best results, the ANT-SIRIUS should be pointing
toward the location indicated by the X on the map.
COAX CABLE
F2F
ALTERNATIVE CABLING
*SOLD SEPARATELY
NOTE: See “Troubleshooting” for additional information regarding on-screen messages.
Figure 2. Installation diagram for one satellite tuner
using the SRK-1W Installation Kit
33
TM-SIRIUS INSTALLATION INSTRUCTIONS
ACTIVATION
It is recommended that the home owner activate the SIRIUS
Subscription Service, to make service package choices
and to assure proper subscription and billing information.
If providing this service for the home owner:
1. Have the IntelliControl ICS System powered up and
active with TM-SIRIUS selected.
2. After displaying the SIRIUS log, the receiver updates
all SIRIUS channels. Do no press any button or perform any operation until updating has been completed. (“Call 1.888.539.SIRIUS to subscribe” will
appear on the display.)
(CONTINUED)
Niles manufactures a line of satellite radio accessories
that include a satellite radio antenna (ANT-SAT) and
Installation Kits for one Satellite Radio Tuner
(SRK-1W) B (See Figure 2).
See NilesAudio.com for the complete line of Satellite
Radio Accessories.
Cascade Audio OUT of the TM-SIRIUS to the Left and
Right Audio IN on the IM-AUDIO Module in the same
number card slot on the Slave chassis. Up to four Slave
chassis may be used in a system.
3. Tune to Channel 0 to get the SIRIUS ID Number. Write
the number down for future reference.
.BTUFS(93
4MBWF(93
5.4*3*64.PEVMF
*."6%*0.PEVMF
4. You can now activate by calling 1.888.539.SIRIUS (7474)
or on the internet at http://activate.siriusradio.com. Have
the home owner’s credit card and SIRIUS ID ready and
follow the prompts to activate the subscription.
Figure 4. Installation diagram for two satellite
tuners using the SRK-2W Installation Kit
Stereo
RCA to
RCA
4UFSFP3$"
Cable
UP3$"$BCMF
SRK-2W
ANT– SAT*
XM/SIRIUS SATELLITE
RADIO ANTENNA
B
A
4-3)2)53
-ODULE
#ARD
SRS –2W
C
IMT–75/50
COAX CABLE
-3
L&R
"VEJP*O
Audio
In
4*3*64
"OUFOOB
ILA–16dB
IMT– 50/75 MF
-3$BTDBEF
L&R
Cascade
"VEJP0VU
Audio
Out
COAX CABLE
(93.BTUFS$IBTTJT
IMT–75/50
CUSTOMER
SUPPLIED
ANTENNA
C
A
SRC–2M
5.".'.
4-3)2)53
-ODULE
#ARD
IMT–50/75 SMB*
5.4*3*64
.PEVMF
'.
"/5
7*%&0
065
".
"/5
$"4$"%&"6%*0
065
$"4$"%&"6%*0
065
$BTDBEF
"VEJP0VU
*SOLD SEPARATELY
$PNNVOJDBUJPO
BOE$POUSPM4XJUDI
4UFSFP
3$"3$"
$BCMF
$"5$BCMF
(934MBWF$IBTTJT
MULTIPLE TM-SIRIUS MODULE
CARDS
When using more than one TM-Sirius Module Card in an
installation, each tuner must be connected to a satellite
radio antenna. The Niles SRK-2W or SRK-4W B allows
for one antenna to provide proper signal strength to
multiple TM-SIRIUS tuner modules. (See Figure 4.)
*."6%*0
.PEVMF
"VEJP*O
&YQBOTJPO
065UPNBTUFS
34
TM-AM/FM INSTALLATION INSTRUCTIONS
INSTALLATION
Figure 2. TM-AM/FM Module connection to antennas.
'.%JQPMF
"OUFOOB
(93
5.".'.
'.
"/5
the TM-AM/FM Module.
$"4$"%&"6%*0
065
1. Carefully slide the TM-AM/FM Module into the
appropriate card slot. (Refer to the GXR2 Installation Worksheet to assure proper card slot number.)
'.
"/5
".
"/5
$"4$"%&"6
065
-
%*0
3
Guides
Figure 1. Inserting the module card
into the GXR2 card cage.
CONNECTING AN ANTENNA TO THE TM-AM/FM
MODULE CARD
$0..6/*$"5*0/
$0/530-48*5$)
5.".'.
.PEVMF
$BTDBEF
"VEJP0VU
When using multiple
chassis, connect the
Left and Right Cascade Audio OUT of
the TM-AM/FM to
the Left and Right
Audio IN on the
IM-AUDIO Module
in the same number card slot on the
Slave chassis. Up
to four Slave chassis may be used in
a system.
.BTUFS(93
4MBWF(93
5.".'..PEVMF
*."6%*0.PEVMF
'.
"/5
4. Tighten thumbscrews.
(Do not over tighten)
5.".'.
3. Be sure the multi-pin
connector is secured
to the header in the
card cage.
".-PPQ
"OUFOOB
5.".'.
insert the module
card.
$"4$"%&"6%*0
065
3
-
CAUTION: The TM-AM/FM Module is susceptible to static
earth ground prior to picking up the TM-AM/FM. Handle
7*%&0
065
".
"/5
".
"/5
$"4$"%&"6%*0
065
-
3
Stereo
RCA to
RCA
4UFSFP3$"
UP3$"$BCMF
Cable
-3$BTDBEF
"VEJP0VU
L&R Cascade
Audio Out
-3
"VEJP*O
L&R
Audio In
Figure 3. Cascade Audio Connections.
When all modules are in place, and the system components have been installed, connect AM and FM antennas.
'.%JQPMF
"OUFOOB
(93.BTUFS$IBTTJT
".-PPQ
"OUFOOB
AM ANTENNA
5.".'.
5.".'.
.PEVMF
1. Connect bare wire ends on antenna to dual spring
clips on TM-AM/FM (polarity not critical).
'.
"/5
7*%&0
065
".
"/5
$"4$"%&"6%*0
065
-
$"4$"%&"6%*0
065
3
$0..6/*$"5*0/
$0/530-48*5$)
2. Position loop antenna for best reception.
$BTDBEF
"VEJP0VU
FM ANTENNA
$BU$BCMF
4UFSFP
3$"3$"
$BCMF
1. Connect F-type connector on antenna to F-type terminal on TM-AM/FM.
(934MBWF$IBTTJT
7*%&0
065
$"4$"%&"6%*0
065
"VEJP*O
*."6%*0
.PEVMF
5.".'.
2. Spread “arms” of dipole antenna as far apart as
possible and position for best reception.
$PNNVOJDBUJPO
BOE$POUSPM4XJUDI
'.
"/5
".
"/5
$"4$"%&"6%*0
065
-
3
$0..6/*$"5*0/
$0/530-48*5$)
&YQBOTJPO
065UPNBTUFS
Figure 4. Expanded System with Cascade Audio Connections.
35
IM-AUDIO INSTALLATION INSTRUCTIONS
Audio Component Connections
1. Carefully slide the IM-AUDIO Module into the
appropriate card slot. (Refer to the GXR2 Installation Worksheet to assure proper card slot number.)
CD Changer
CS-12V
IR Flasher
on Front
panel
TM-AM/FM
Module
(93
4-05
4-05
4-05
4&3*"-/6.#&3
4-05
4-05
4-05
1BHF5SJHHFS
3
;0/&
;0/&
77NJO
5IJTEFWJDFDPNQMJFTXJUIQBSUPGUIF'$$3VMFT0QFSBUJPOJTTVCKFDUUPUIFGPMMPXJOHUXPDPOEJUJPOT
5IJTEFWJDFNBZOPUDBVTF
IBSNGVMJOUFSGFSFODFBOE
UIJTEFWJDFNVTUBDDFQUBOZJOUFSGFSFODFSFDFJWFEJODMVEJOHJOUFSGFSFODFUIBUNBZDBVTFVOEFTJSFEPQFSBUJPO
GXR2 Master Chassis
;0/&
;0/&
;0/&
/JMFT"VEJP$PSQPSBUJPO
.JBNJ'MPSJEB64"
065
-
;0/& 1BHF*OQVU
77NJO
".
"/5
$"4$"%&"6%*0
To Unswitched
Outlet
IM-AUDIO
Module
77NJO
5.".'.
'.
"/5
Audio OUT L&R
77NJO
CAUTION: The IM-AUDIO Module is susceptible to static
earth ground prior to picking up the IM-AUDIO. Handle
Sync:
NOTE: If discrete IR ON/OFF codes are available for
the specific source component, 12V or Video Sync sensing is not required. If “Toggle Power” is the only IR
code available, use one of the Sync methods below to
manage turning On and Off the component.
77NJO
the IM-AUDIO Module.
Carefully run the flasher wire back to the IntelliControI
ICS Modular MultiZone Receiver and plug it into the IR
OUT jack on the appropriate IM-AUDIO card.
77NJO
INSTALLATION
*30VUQVU
7
4:/$
*/
-
-
3
3
7$POUSPM
0VUN"
-
3
"6%*0
*/
)54ZOD
-
"6%*0
*/
-
7$POUSPM
0VUN"
3
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
7$POUSPM
0VUN"
-
3
7$POUSPM
0VUN"
$-"44**8*3*/(
-
%PVCMF*OTVMBUFE
8IFOTFSWJDJOHVTFPOMZ
JEFOUJDBMSFQMBDFNFOUQBSUT
%FTJHOFEBOE&OHJOFFSFEJOUIF64".BEFJO.BMBZTJB
Communication
& Control Switch
GXR2 Slave Chassis
CAT-5 Cable
;0/& 1BHF*OQVU
;0/&
;0/&
;0/&
.JBNJ'MPSJEB64"
1BHF5SJHHFS
77NJO
4-05
77NJO
4-05
77NJO
4&3*"-/6.#&3
4-05
;0/&
77NJO
4-05
;0/&
77NJO
4-05
7PMUT_)[8BUUT.BY
$0..6/*$"5*0/
$0/530-)6#
IR Cascade
OUT to IR IN
(93
4-05
3
7$POUSPM
0VUN"
$"65*0/3FGFSUPUIFPQFSBUJPOTHVJEFGPSMFTTUIBO8JOTUBMMBUJPOT
0VUUP.BTUFS
L&R Cascade Audio
OUT to Audio IN
$-"44**8*3*/(
-
7$POUSPM
0VUN"
."$"%%3&44
3
7$POUSPM
0VUN"
&91"/4*0/
3
$"4$"%&"6%*0
065
3
$"4$"%&"6%*0
065
$-"44**8*3*/(
3
)5*3*O
$-"44**8*3*/(
-
*3065
*3*/
77NJO
$"4$"%&"6%*0
065
*3065
*3*/
3
7*%&0
4:/$
*/
*."6%*0
-
$"4$"%&"6%*0
065
7
4:/$
*/
7*%&0
4:/$
*/
*."6%*0
3
"/5
-
*.J10%
$"4$"%&"6%*0
065
5.4*3*64/JMFT"VEJP$PSQPSBUJPO.JBNJ'MPSJEB64"
5.9.
*..1
Guides
"/5
J1PE
1JO
$POOFDUPS
*30VUQVU
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
-
"6%*0
*/
3
*3065
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
7$POUSPM
0VUN"
*."6%*0
3
$"4$"%&"6%*0
065
7*%&0
4:/$
*/
*3*/
3
"6%*0
*/
-
7
4:/$
*/
*."6%*0
*3065
7*%&0
4:/$
*/
*3*/
*."6%*0
7
4:/$
*/
*."6%*0
*3065
*."6%*0
IR
Attach a Niles IR Flasher (Niles model MF1, MF1-VF)
directly over the IR eye on the component. (Shine a
flashlight onto the front panel of the component to find
the IR eye if it is not obvious.)
Audio
When all IM-Audio modules are installed in the IntelliControI ICS Modular MultiZone Receiver, connect the
Left & Right line level audio OUT of source the component to the Left & Right audio IN on the appropriate IMAUDIO card.
7*%&0
4:/$
*/
*3*/
*."6%*0
CONNECTING AN AUDIO COMPONENT TO
THE IM-AUDIO MODULE
7
4:/$
*/
3
$"4$"%&"6%*0
065
$-"44**8*3*/(
-
)54ZOD
-
"6%*0
*/
$-"44**8*3*/(
3
-
7$POUSPM
0VUN"
3
-
7$POUSPM
0VUN"
$-"44**8*3*/(
3
-
3
7$POUSPM
0VUN"
$-"44**8*3*/(
-
3
7$POUSPM
0VUN"
$-"44**8*3*/(
-
7$POUSPM
0VUN"
3
7$POUSPM
0VUN"
%PVCMF*OTVMBUFE
0VUUP.BTUFS
&91"/4*0/
3
$"4$"%&"6%*0
065
7PMUT_)[8BUUT.BY
$0..6/*$"5*0/
$0/530-)6#
."$"%%3&44
IM-AUDIO Module Cards
$-"44**8*3*/(
3
)5*3*O
Expansion
Out to Master
Figure 2. IM-AUDIO A/V Hook Up Diagram.
CONNECTING A VIDEO COMPONENT AND
CURRENT SENSOR
Video Sync
If the source component has a composite video output,
connect the composite video OUT of the source component to Video Sync IN.
36
IM-AUDIO INSTALLATION INSTRUCTIONS
(CONTINUED)
3-30 Volt Sync
If the source component has no Video output, connect the control voltage from a current sensing device
like the Niles CS-12V to Voltage Sync IN. Polarity:
TIP=+12VDC; SLEEVE=GND.
Using the Niles CS-12V Current Sensor:
The CS-12V will sense the difference in current draw
between stand-by and on for the source it is sensing.
The CS-12V will send 12V to the sync input to let the
IntelliControl ICS Modular MultiZone Receiver know that
the source is on. The IntelliControl ICS Modular MultiZone
Receiver will appropriately manage power commands for
the source component by knowing when it is on or off.
EXPANDING THE SYSTEM WITH AUDIO
Cascade Audio OUT of the IM-AUDIO to the Left and
.BTUFS(93
4MBWF(93
*."6%*0.PEVMF
*."6%*0.PEVMF
1. Plug the power cord of the source component into
the AC jack on the CS-12V.
2. Plug the power cord for the CS-12V into an
un-switched AC outlet.
3. Connect the 12V output of the CS-12V in to the
3-30V Sync IN on the IM-AUDIO.
4UFSFP3$"
UP3$"$BCMF
Audio/Video Component Connections
AV Component
IR Flasher
on Front
panel
-FGUBOE3JHIU
$BTDBEF"VEJP065
-FGUBOE3JHIU
"VEJP*/
EXPANDING THE SYSTEM USING IR
Audio OUT L&R
Video OUT
IM-AUDIO
Module
TM-AM/FM
Module
(93
;0/& 1BHF*OQVU
4-05
1BHF5SJHHFS
;0/&
;0/&
;0/&
;0/&
77NJO
4-05
77NJO
4&3*"-/6.#&3
4-05
77NJO
4-05
77NJO
4-05
77NJO
4-05
77NJO
GXR2 Master Chassis
;0/&
.JBNJ'MPSJEB64"
When using multiple chassis, connect the IM-AUDIO IR
OUT on the Slave chassis to the IR IN on the IM-AUDIO
Module in the same number card slot on the Master
chassis.
*30VUQVU
7*%&0
4:/$
*/
*3*/
*3065
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
7$POUSPM
0VUN"
3
"6%*0
*/
$-"44**8*3*/(
-
)54ZOD
-
"6%*0
*/
-
7$POUSPM
0VUN"
3
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
3
7$POUSPM
0VUN"
7$POUSPM
0VUN"
$-"44**8*3*/(
-
7$POUSPM
0VUN"
%PVCMF*OTVMBUFE
&91"/4*0/
(93
;0/& 1BHF*OQVU
.'
.JDSPnBTIFS
Communication
& Control Switch
CAT-5 Cable
;0/&
;0/&
;0/&
;0/&
;0/&
*3*/
77NJO
77NJO
1BHF5SJHHFS
77NJO
4-05
77NJO
4-05
4MBWF(93
*."6%*0.PEVMF
7$POUSPM
0VUN"
7PMUT_)[8BUUT.BY
.JBNJ'MPSJEB64"
4&3*"-/6.#&3
4-05
77NJO
4-05
.BTUFS(93
*."6%*0.PEVMF
IR Cascade
OUT to IR IN
GXR2 Slave Chassis
4-05
3
$0..6/*$"5*0/
$0/530-)6#
L&R Cascade Audio
OUT to Audio IN
4-05
$-"44**8*3*/(
-
."$"%%3&44
3
7$POUSPM
0VUN"
0VUUP.BTUFS
3
$"4$"%&"6%*0
065
3
$"4$"%&"6%*0
065
$-"44**8*3*/(
3
)5*3*O
77NJO
3
-
-
3
7
4:/$
*/
*."6%*0
-
3
$"4$"%&"6%*0
065
J1PE
1JO
$POOFDUPS
*."6%*0
-
"/5
3
$"4$"%&"6%*0
065
*.J10%
-
5.4*3*64/JMFT"VEJP$PSQPSBUJPO.JBNJ'MPSJEB64"
5.9.
*..1
$"4$"%&"6%*0
065
"/5
$POEVDUPS
"8(8JSF
*3065
*30VUQVU
"6%*0
*/
3
3
$"4$"%&"6%*0
065
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
7*%&0
4:/$
*/
*3*/
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
-
"6%*0
*/
3
-
*3*/
7
4:/$
*/
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
7$POUSPM
0VUN"
*."6%*0
3
$"4$"%&"6%*0
065
*3065
7*%&0
4:/$
*/
3
*3*/
7
4:/$
*/
*."6%*0
"6%*0
*/
7*%&0
4:/$
*/
*3065
7
4:/$
*/
*."6%*0
-
*3*/
*3065
7*%&0
4:/$
*/
*."6%*0
*3*/
7
4:/$
*/
*."6%*0
7*%&0
4:/$
*/
*."6%*0
7
4:/$
*/
3
$"4$"%&"6%*0
065
$-"44**8*3*/(
-
)54ZOD
-
"6%*0
*/
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
3
$-"44**8*3*/(
-
7$POUSPM
0VUN"
3
7$POUSPM
0VUN"
7$POUSPM
0VUN"
7$POUSPM
0VUN"
$-"44**8*3*/(
-
7$POUSPM
0VUN"
3
7$POUSPM
0VUN"
%PVCMF*OTVMBUFE
0VUUP.BTUFS
&91"/4*0/
3
$"4$"%&"6%*0
065
7PMUT_)[8BUUT.BY
$0..6/*$"5*0/
$0/530-)6#
."$"%%3&44
3
)5*3*O
Expansion
Out to Master
Figure 3. IM-AUDIO A/V Hook-Up Diagram
Figure 5. IR Pass-Through Connections
37
TM-HD/R INSTALLATION INSTRUCTIONS
INSTALLATION
WARNING: Always turn power OFF to the IntelliControl
ICS Modular MultiZone Receiver and be sure AC
line cord is disconnected to avoid damage and electrical shock before making any connections to the
TM-HD/R Module.
(93
'.
"/5
5.)%3
CAUTION: The TM-HD/R Module is susceptible to static
earth ground prior to picking up the TM-HD/R. Handle
'.%JQPMF
"OUFOOB
".
"/5
-
1. Carefully slide the TM-HD/R Module into the appropriate card slot. (Refer to the GXR2 Installation
Worksheet to assure proper card slot number.)
7*%&0
065
$"4$"%&"6%*0
065
$"4$"%&"6%*0
065
3
$0..6/*$"5*0/
$0/530-48*5$)
".-PPQ
"OUFOOB
5.)%3
.PEVMF
$BTDBEF
"VEJP0VU
Figure 2. TM-HD/R Module connection to antennas.
5.)%3
'.
"/5
'.%JQPMF
"OUFOOB
".
"/5
$"4$"%&
"6%*0
065
-
3
Guides
".-PPQ
"OUFOOB
CONNECTING AN ANTENNA TO THE TM-HD/R
MODULE CARD
2. Position loop antenna for best reception.
FM Antenna
1. Connect an antenna with a F-type connector to
F-type terminal on TM-HD/R.
2. Spread “arms” of dipole antenna as far apart
as possible and position for best reception.
AM Antenna
1. Connect bare wire ends on antenna to dual spring
clips on TM-HD/R (polarity not critical).
'.
"/5
5.)%3
When all modules are in place, and all system
components have been installed, connect AM and FM
antennas.
".
"/5
7*%&0
065
$"4$"%&"6%*0
065
-
$"4$"%&"6%*0
065
3
Figure 4. Enlargement – AM and FM antennas connecting to module card.
5.)%3
.PEVMF
$BTDBEF
"VEJP0VU
Figure 3. Enlargement – AM and FM antennas
connecting to module card.
38
TM-HD/R INSTALLATION INSTRUCTIONS
(CONTINUED)
Cascade Audio OUT of the IM-AUDIO to the Left and
EXPANDED SYSTEMS DIAGRAM
'.%JQPMF
"OUFOOB
(93.BTUFS$IBTTJT
".-PPQ
"OUFOOB
5.)%3
4MBWF(93
5.)%3.PEVMF
*."6%*0.PEVMF
5.)%3
.PEVMF
.BTUFS(93
'.
"/5
".
"/5
7*%&0
065
$"4$"%&"6%*0
065
-
$"4$"%&"6%*0
065
3
$0..6/*$"5*0/
$0/530-48*5$)
$BTDBEF
"VEJP0VU
$PNNVOJDBUJPO
BOE$POUSPM4XJUDI
$BU$BCMF
4UFSFP
3$"3$"
$BCMF
(934MBWF$IBTTJT
5.)%3
'.
"/5
$"4$"%&"6%*0
065
3
-3$BTDBEF
"VEJP0VU
7*%&0
065
$"4$"%&"6%*0
065
"VEJP*O
-
5.".'.
*."6%*0
.PEVMF
".
"/5
'.
"/5
".
"/5
$"4$"%&"6%*0
065
-
3
$0..6/*$"5*0/
$0/530-48*5$)
&YQBOTJPO
065UPNBTUFS
Figure 5. Expanded system with Cascade
Audio connections.
4UFSFP3$"
UP3$"$BCMF
-3
"VEJP*O
39
IM-SERVER INSTALLATION INSTRUCTIONS
INSTALLATION
IntelliControl ICS Modular MultiZone Receiver and be
the IM-SERVER Module.
CAUTION: The IM-SERVER Module is susceptible to static
earth ground prior to picking up the IM-SERVER. Handle
1. Carefully slide the IM-SERVER Module into the appropriate card slot. (Refer to the GXR2 Installation
Worksheet to assure proper card slot number.)
the Left and Right line level audio OUT of the Media
Server to the Left & Right audio IN on the appropriate
IM-SERVER.
Network Device
Connect a CAT-5 cable from the Network Device port
of the IM-SERVER card to the network switch/hub that
the Media server/Player is connected to.
IR OUT
Attached a Niles IR Flasher (Niles model MF1, MF1VF) directly over the IR eye on the component. (Shine
a flashlight onto the front panel of the media server to
find the IR OUT eye if it is not obvious.)
Carefully run the flasher wire back to the IntelliControl
ICS Modular Multizone Receiver and plug it into the IR
jack on the appropriate IM-SERVER card.
5.".'.
NOTE: An IM-SERVER card can be used for each stream
on a multi-stream capable Media Server.
'.
"/5
".
"/5
$"4$"%&"6%*0
Media Servers
065
-
3
DMS4 MEDIA SERVER
Guides
IR IN
SWITCH/HUB
HUB
1
Audio Out
2
3
4
L
R
CAT-5
CABLES
STEREO- RCARCA CABLE
CONNECTING A MEDIA SERVER OR PLAYER TO
THE IM-SERVER
Preparation for Connection
Make sure that the Media Server/Player to be used
with the IntelliControl ICS Modular MultiZone Receiver
is connected to the customer’s home network via a network switch/hub and CAT-5 cables. It is recommended
to test all remote control and music content functionality of the Media Server/Player before connecting to the
ICS IntelliControl System.
Audio
When all IM-SERVER cards are installed in the Master
IntelliControl ICS Modular MultiZone Receiver, connect
IR
CONNECTION
CAT-5
CABLES
GXR2
Figure 2. Audio Connections
40
IM-SERVER INSTALLATION INSTRUCTIONS
Cascade Connections for System Expansion
(CONTINUED)
.BTUFS(93
4MBWF(93
*.4&37&3.PEVMF
*."6%*0.PEVMF
/&5803,
%&7*$&
*.4&37&3
Master Chassis
GXR2
IR OUT Cascade
to IR IN
*3065
*3*/
-
"6%*0
*/
-
L&R
Cascade
Audio
OUT to
Audio IN
3
3
4UFSFP3$"
UP3$"$BCMF
$"4$"%&"6%*0
065
Communication
& Control Switch
CAT-5 Cable
GXR2 Slave Chassis
(93
;0/& 1BHF*OQVU
;0/&
;0/&
;0/&
;0/&
-FGUBOE3JHIU
$BTDBEF"VEJP065
;0/&
.JBNJ'MPSJEB64"
4-05
1BHF5SJHHFS
-FGUBOE3JHIU
"VEJP*/
77NJO
4-05
77NJO
4&3*"-/6.#&3
4-05
77NJO
4-05
77NJO
4-05
77NJO
4-05
77NJO
*30VUQVU
"6%*0
*/
3
3
$"4$"%&"6%*0
065
7*%&0
4:/$
*/
*3*/
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
-
"6%*0
*/
3
3
$"4$"%&"6%*0
065
-
7
4:/$
*/
7
4:/$
*/
7*%&0
4:/$
*/
*3*/
*3065
7$POUSPM
0VUN"
*."6%*0
3
$"4$"%&"6%*0
065
*3065
3
7*%&0
4:/$
*/
*3*/
*."6%*0
"6%*0
*/
7
4:/$
*/
*3065
*."6%*0
7*%&0
4:/$
*/
*3*/
-
7
4:/$
*/
*."6%*0
*3065
*."6%*0
7*%&0
4:/$
*/
*3*/
*."6%*0
7
4:/$
*/
$-"44**8*3*/(
-
)54ZOD
-
"6%*0
*/
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
$-"44**8*3*/(
3
-
3
$-"44**8*3*/(
-
3
)5*3*O
7$POUSPM
0VUN"
3
7$POUSPM
0VUN"
7$POUSPM
0VUN"
7$POUSPM
0VUN"
7$POUSPM
0VUN"
7$POUSPM
0VUN"
%PVCMF*OTVMBUFE
0VUUP.BTUFS
&91"/4*0/
3
$"4$"%&"6%*0
065
7PMUT_)[8BUUT.BY
$0..6/*$"5*0/
$0/530-)6#
."$"%%3&44
.BTUFS(93
4MBWF(93
*.4&37&3.PEVMF
*."6%*0.PEVMF
Expansion
Out to Master
/&5803,
%&7*$&
Figure 3. IM-SERVER A/V Hook-up diagram
*.4&37&3
*3*/
Cascade Audio OUT of the IM-SERVER to the Left and
*3*/
-
-
EXPANDING THE SYSTEM USING IR
When using multiple chassis, connect the IM-AUDIO IR
OUT on the Slave chassis to the IR IN on the IM-AUDIO
Module in the same number card slot on the Master
chassis.
.'
.JDSPnBTIFS
*3065
"6%*0
*/
3
$POEVDUPS
"8(8JSF
*3065
3
$"4$"%&"6%*0
065
*Prod ID: FG00933 3.5mm Cable
Figure 5. IR Pass-Through Connections
41
USER INTERFACES
ZIGBEE™ NETWORKS
HOW A ZIGBEE RF NETWORK WORKS
The iRemote ® utilizes ZigBee radio technology to communicate bi-directionally to the IntelliControl ICS Modular MultiZone Receiver. ZigBee radios operate in the
2.4GHz band. Both the iRemote handheld remote and
the charging base have radios based on ZigBee Technology. Each radio has an operational Radio-Frequency
(RF) range as depicted in below. The operational RF
range can vary depending on the home’s construction and RF environment. When your iRemote is out of
range, the LCD will display the message; “Searching
for Network.” Once you have come back into range,
the LCD will display the message, “Connecting to Network.” When network connection is complete, the LCD
will display the correct “Now Playing” screen and cor-
responding metadata. When more than one iRemote is
installed into a home, the operational RF ranges of the
additional iRemote Bases combine to form a Mesh Network. This mesh network is the sum of all the operational
ranges and greatly expands the RF coverage area. In
some cases it may be necessary to place an additional
iRemote Charger Base in a different area of the house
to extend the RF coverage area. It may also be necessary to place an iRemote Charger Base on each floor of
a multi-story structure, to extend the RF coverage area
from one floor to another.
iRemote Charger bases are sold separately for this
purpose.
ZIGBEE RF NETWORKS INFORMATION
#FESPPN
.BTUFS
#FESPPN
#FESPPN
#BUISPPN
&OUSBODF
,JUDIFO
'BNJMZ3PPN
-JWJOH
3PPN
.BTUFS$IBSHJOH#BTF4UBUJPO
J3FNPUF3FQFBUFS$IBSHJOH#BTF4UBUJPO
42
USER INTERFACES
ZIGBEE™ NETWORKS
CONNECTING THE MASTER CHARGING BASE
At least one iRemote Charging Base must remain connected to the IntelliControl ICS Modular MultiZone
Receiver, via a CAT-5 cable, to convert ZigBee radio
communication messages to system control commands.
Once connected, designate this base the “Master Charging Base” (See below). All other iRemote Charging
Bases in the system can be plugged into any unswitched
AC outlet to provide wireless two-way radio connectivity
and iRemote battery charging.
GXR2
(CONTINUED)
CONNECTING THE REMAINING
IREMOTE’S FOR NETWORK CONFIGURATION
All remaining iRemote’s must be placed in a charging
base and temporarily connected to the IntelliControl
ICS Modular MultiZone Receiver for network configuration. This ensures that both the handheld remote
controls and the charging bases will be configured correctly (See below).
Before proceeding, make sure you have decided which
iRemote charging base will be assigned as the Master
Charging Base. Place the MAC ID sticker on the GXR2
Installation worksheet.
GXR2
5.".'.
7*%&0
065
$"4$"%&"6%*0
065
$0..6
$0/5
12V DC
Power
Supply
'.
"/5
".
"/5
$"4$"%&"6%*0
065
-
7*%&0
065
$"4$"%&"6%*0
065
3
CAT-5 Cables
CAT-5 Cable
iREMOTE Master
Charging Base
iREMOTE
Repeater Base
iREMOTE
Repeater Base
iREMOTE
Repeater Base
iREMOTE Master
Charging Base
43
USER INTERFACES
ZIGBEE™ NETWORKS
CONFIGURING THE iREMOTE ® NETWORK
To ensure optimal two-way communication between
multiple iRemote’s and a IntelliControl ICS Modular
MultiZone Receiver, we have devised a methodology
that assigns and tracks 3 characteristics for each iRemote
in a system. During iRemote Network configuration,
each iRemote is assigned an Network ID #, an RF Channel # and a unique Unit ID #.
Up to fifteen iRemote’s can exist on one RF Network.
Currently, two networks are provided to allow a total of
thirty iRemotes to communicate simultaneously, in a single system. An advantage of utilizing this methodology
is that if your neighbor owns an IntelliControl ICS system with iRemote’s, their iRemotes will not interfere with
the iRemotes from your system.
(CONTINUED)
Configuring the iRemote ZigBee RF Network is accomplished during system configuration using the IntelliFile ®3
software after all the components are connected and
powered up (see below).
CONFIGURING THE iREMOTE NETWORK
Network ID #(1-15): Selects unique Network ID
number for the first fifteen iRemotes in a system.
RF Channel #(1-15): Selects a specific RF frequency for
communication to the system on the selected Network.
Unit ID #(1-15): Selects a unique ID Number for
each iRemote in the Network so multiple iRemotes can
simultaneously communicate to the system without any
interference.
44
USER INTERFACES
CAT-5 CONNECTION
WIRING TERMINATION DIAGRAM
The IntelliControl ICS touch screens and keypads connect to the IntelliControl ICS Modular MultiZone Receiver
via CAT-5 cable. For the system to function properly all
runs of CAT-5 must be pulled in home-runs from the
touch screen locations to the system head end where
the IntelliControl ICS Modular MultiZone Receiver and
other system components will be located.
$"5$BCMF
$0/5"$5,&:1"%
$0/5"$5,&:1"%
5IJTEFWJDFDPNQMJFTXJUIQBSUPGUIF'$$3VMFT
0QFSBUJPOJTTVCKFDUUPUIFGPMMPXJOHUXPDPOEJUJPOT
5IJTEFWJDFNVTUBDDFQUBOZJOUFSGFSFODFBOE
UIJT
EFWJDFNVTUBDDFQUBOZJOUFSGFSFODFSFDFJWFEJODMVEJOH
JOUFSGFSFODFUIBUNBZDBVTFVOEFTJSFEPQFSBUJPO
UIJT
ª/JMFT"VEJP$PSQPSBUJPO
.JBNJ'MPSJEB64"-""$/
$-"444&-7%&7*$&
4:45&.
$-"444&-7%&7*$&
*34&/403
4:45&.
4ZTUFN
5FSNJOBM
The runs of CAT-5 must be terminated with RJ-45 connectors using the T-568A pinout configuration as follows:
*34&/403
Contact connecting to the
Communication and Control Switch
RJ-45 Plugs
1JO
GXR2
H ( P # C 0 CS #3
H ( P # C 0 CS #3
5"
5"
$0..6/*$"5*0/
$0/530-48*5$)
Pin #
Description
Color Code
1
2
3
4
5
6
7
8
TX+
TX–
RX+
IR Signal
IR Ground
RX–
UI Power
UI Ground
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
$"5$BCMF
$"5$BCMF
%*41-":,&:1"%
%*41-":,&:1"%
UIJT
UIJT
$-"444&-7%&7*$&
4:45&.
*34&/403
$-"444&-7%&7*$&
4ZTUFN
5FSNJOBM
DISPLAY
4:45&.
*34&/403
DISPLAY
Display Keypad connecting to the
Note: TX+ = transmit, RX+ = receive, UI = user interface.
Important: All CAT-5 runs must be terminated
using T-568A pinouts.
GXR2
CONNECTIONS
Using a properly configured CAT-5 cable, connect
the system terminal on the touch screen to any of the
RJ-45 communication and control hub ports on the
IntelliControl ICS Modular MultiZone Receiver as shown
in the following diagrams.
CAT-5 Cable
System
Terminal
4ZTUFN
*34FOTPS
SINGLE
4ZTUFN
*34FOTPS
SINGLE
Single Keypad connecting to the
45
USER INTERFACES
IR SENSOR CONNECTION
ADDING AN IR SENSOR
To add an IR sensor to a touch screen or keypad, use
the wiring diagrams and connector detail that follow to
adapt an RJ-45 connector from a touch screen to the
plug-in wire terminals on the IR sensor.
Niles IR Connection
RJ-45
4UBUVT
%BUB
Using a properly configured CAT-5 cable, connect the
IR Sensor terminal on the touch screen to the plug-in terminal on an IR Sensor as shown.
CAUTION: These connections are different than those used from the
touch screens to the IntelliControl ICS Modular MultiZone Receiver.
Be sure to check wire configuration and connections before powering up the system.
(SPVOE
7%$
5BC
%PXO
$0/5"$5,&:1"%
UIJT
4:45&.
4UBUVT
(SPVOE
$"5
$-"444&-7%&7*$&
*34&/403
*34FOTPS
5FSNJOBM
7
%BUB
CONTACT
Niles IR Sensor to ICS Keypad IR Sensor
Input for RJ-45 Pinout.
Pin #
1
2
3
4
5
6
7
8
Color Code
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
Connector
12V
Data
Ground
Empty
Status
Empty
Empty
Empty
IR Sensor
IR sensor to Contact touch screen connection
$"5
%*41-":,&:1"%
UIJT
$-"444&-7%&7*$&
4:45&.
*34&/403
*34FOTPS
5FSNJOBM
DISPLAY
IR Sensor
IR sensor to Display Keypad connection
Four Pair
Twisted Cable
4ZTUFN
*34FOTPS
IR Sensor
Terminal
SINGLE
IR Sensor
IR sensor to Single Keypad connection
46
VOLUME CONTROLS
The GXR2 can be configured via the IntelliFile ® 3
Volume Controls, connected to an ICS system via a
software for volume control integration. Below is an
Niles MCV-HUB4, to independently adjust the listening
example of one zone using several Niles VCS-100
level of three separate areas.
MASTER BEDROOM
MASTER BATH
VCS-100
MASTER TERRACE
VCS-100
VCS-100
16/4 Speaker Wire
MCV-HUB4
CAT-5 Cable
TM-AM/FM
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
47
EXPANDING A ZONE WITH AN EXTERNAL AMPLIFIER
To provide more power in a zone, use an external
external amplifiers for zones requiring additional
amplifier. A preamplifier output connection for each
power. Below is an example of how to connect an
zone of the IntelliControl ICS allows you to connect
amplifier to the GXR2 Modular Multizone Receiver.
®
ZONE 1
MASTER BEDROOM
Two-Conductor
Speaker Cable
SI-245
Variable AUDIO
Line Level
TM-AM/FM
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
CAT-5 Cable
48
DOORBELL INTERFACE
of a doorbell integrated into an ICS system using a
software for doorbell integration. Below is an example
Niles DBI-1 Doorbell Interface.
TM-AM/FM
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
DBI-1
49
TELEPHONE/PAGING SYSTEM INTEGRATION
The GXR2 can be configured via the IntelliFile® 3 software
to the telephone/paging system via a telephone control
for telephone/paging system integration. Below are two
unit. The second example consists of an expanded system
examples. The first example uses a single GXR2 connected
using a Niles AVDA-3 Distribution Amplifier.
TELEPHONE
CONTROL UNIT
Page Input
TM-AM/FM
FM
ANT
VIDEO
OUT
AM
ANT
CASCADE AUDIO
OUT
L
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
TM-AM/FM
GXR2
TELEPHONE
CONTROL UNIT
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
Master Chassis
COMMUNICATION
& CONTROL SWITCH
Slave1 to Master CAT-5
TM-AM/FM
GXR2
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
Slave 1 Chassis
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
Slave2 to Slave1 CAT-5
TM-AM/FM
AVDA-3
Slave 2 Chassis
GXR2
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
50
HOME THEATER INTEGRATION
components shared with the home theater system to be
software for home theater system integration. The home
turned on, controlled via IR and turned off as needed.
theater integration ports enable audio and video source
Below is an example using an IntelliControl ® MSU.
DSS
AUDIO/VIDEO RECEIVER
AUDIO
1
VIDEO
FRONT
REAR
R
DVD
2
L
DSS
CD
R
DVD
CENTER
– +
VIDEO 1
VIDEO 2
L
R
L
CD CHANGER
R
L
TM-AM/FM
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
R
COMMUNICATION
& CONTROL SWITCH
TM-XM
Cascade Audio
Flasher
Output
TM-SIRIUS Cascade Audio
DSS Cascade Audio
12V Output
DVD Cascade Audio
CD Cascade Audio
Flasher
Output
12V Output
Flasher
Output
INTELLICONTROL MSU
51
LINKING MULTIPLE ZONES
on and change sources together. The volume can be
software to enable zone linking. Below is an example
controlled for each zone separately from an user
of 3 zones linked together. All 3 zones are turned
interface such as a Contact Touch Screen.
PATIO
CAT-5
Cable
POOL AREA
CABANA
16/4
Speaker
Wire
TM-AM/FM
FM
ANT
AM
ANT
CASCADE AUDIO
OUT
L
VIDEO
OUT
CASCADE AUDIO
OUT
R
COMMUNICATION
& CONTROL SWITCH
52
SELECTING A PLACEMENT
SITE FOR THE GXR2
Like any high-fidelity component, the GXR2 will last much
longer if it is given adequate ventilation for proper cooling. When installing the GXR2 in a cabinet, be sure that
the cabinet’s rear is open to receive fresh air in order to
provide proper cooling. If the cabinet’s design does not
accommodate an open rear, install two small “boxer fans”
to provide continuous airflow into and out of the cabinet.
Place the GXR2 so it has at least seven inches of free air
space above it. If the receiver is located on a carpeted surface, place a board under the receiver’s feet. Do not block
the ventilation holes on the top and bottom of the GXR2.
CAUTION!
When using low-impedance speaker
loads (less than 8 ohms Nominal)
you must use boxer fans as shown.
Boxer Fan (55 CFM) directly centered
7” on top and in back of the GXR2.
(93
. 0 % 6
- " 3 .
6 - 5 * ;
0 / & 3
& $ & * 7
& 3
Flange for butting
bracket against
a joist
Rack Mount Ears
Fastening the Rack Mount Panels.
INSTALLING SOURCE CARD
MODULES
the card module.
Make sure that there is a minimum
of 7” of free air space above the
amplifier and 3” on each side for
proper ventilation..
CAUTION: The card module is susceptible to static discharge. Be sure to use a grounding strap or touch an
earth ground prior to picking up the module. Handle the
card by its edges.
Allow a minimum of 2” of depth
behind unit to accommodate cables
and connectors.
If the cabinet rear is not open to fresh
air or if you’re using low-impedance
loads, install two “boxer fans” to
provide continuous air flow into and
out of the cabinet.
1. Carefully slide the card module into the appropriate
card slot. (Refer to the GXR2 Installation Worksheet
to assure proper card slot number.)
INSTALLING RACK EARS
TOOLS REQUIRED:
2. Place a rack mount panel on the GXR2 side panel,
aligning the holes in the rack mount panel, with the
holes in the GXR2 side panel.
3. Replace all four screws, fastening the rack mount
panel to the chassis.
1. Remove the four chassis screws located at the front
of one of the IntelliControl ICS GXR2 Modular
MultiZone Receiver side panels.
5.".'.
• Screwdriver with No. 2 Phillips bit
'.
"/5
".
"/5
$"4$"%&"6
065
-
%*0
3
Guides
Inserting the module card into the GXR2 card cage
Note: Do not over tighten the screws.
4. Repeat procedure for the other side of the GXR2.
53
CONFIGURING AND INSTALLING USER INTERFACE CONTROLS
CONFIGURING USER INTERFACE CONTROLS
CAT-5 WIRING
TERMINATION DIAGRAM
INSTALLING AN EXTERNAL
IR SENSOR
The IntelliControl ICS touch screens and keypads connect
to the IntelliControl ICS Modular MultiZone Receiver via
CAT-5 cable. For the system to function properly all runs
of CAT-5 must be pulled in home-runs from the touch
screen and keypad locations to the system head end
where the IntelliControl ICS Modular MultiZone Receiver
and other system components will be located.
To add an IR sensor to a user interface, use the wiring
diagrams and connector detail that follow to adapt an
RJ-45 connector from a user interface to the plug-in
wire terminals on the IR sensor.
4UBUVT
The runs of CAT-5 must be terminated with RJ-45 connectors using the T-568A pinout configuration as follows:
RJ-45 Plugs
%BUB
(SPVOE
7%$
5BC
%PXO
1JO
4UBUVT
H ( P # C 0 CS #3
H ( P # C 0 CS #3
5"
5"
IntelliControl ICS RJ-45 Pinout and checklist
Pin #
Description
Color Code
1
2
3
4
5
6
7
8
TX+
TX–
RX+
IR Signal
IR Ground
RX–
UI Power
UI Ground
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
7
(SPVOE
%BUB
IR Sensor to Touch Screen and Keypad pinout
Pin #
1
2
3
4
5
6
7
8
Color Code
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
Connector
12V
Data
Ground
Empty
Status
Empty
Empty
Empty
Note: TX+ = transmit, RX+ = receive, UI = user interface.
CONNECTING IR SENSORS
$0/5"$5,&:1"%
Using a properly configured CAT-5 cable, connect
the IR Sensor terminal on the touch screen or keypad
to the plug-in terminal on an IR Sensor as shown.
CAUTION: These connections are different than those used from
the touch screens or keypads to the IntelliControl ICS Modular
MultiZone Receiver. Be sure to check wire configuration and connections before powering up the system.
UIJT
$"5
$-"444&-7%&7*$&
4:45&.
*34&/403
*34FOTPS
5FSNJOBM
CONTACT
IR Sensor
IR sensor to Contact touch screen connection
54
CONFIGURING AND INSTALLING USER INTERFACE CONTROLS
INSTALLING USER INTERFACE CONTROLS
PREPARING FOR INSTALLATION
Determine the best mounting location for the Contact,
based on framing, electrical wiring, fixtures and any
mechanical limitations present in the stud space. Make
sure the area behind the touch screen or keypad is at
least 2 inches deep and clear of any obstructions.
BKT-2
CAT-5 Cable
New
Construction
Bracket
The Contact touch screen is designed to provide the
best screen resolution when installed at a mounting
height of 60” on-center (See Figure 10).
US
/FM
AM
SIRI
XM
m
Albu
hite
eW
es
Th
eatl
eB n
Th lutio
vo
Re
d
iPo
Me
Sh
8 of
13
nu
le
uff
CONTACT
Faceplate
Figure 11. Touch Screen Installation
BKT-2
CAT-5 Cable
New
Construction
Bracket
9.
%
J10
AM
/F
M-
r
ne
Tu
.7
98
FM
;
+";
$,
30
&4
#-6
%&'
"#$
s
Fav
FM
AM
'.
".
*64
4*3
$"44*
$-"
+,-
()*
123
567
4
./0
;
89:
&OU
FS
MBZ
%JTQ
4&-
&$5
Figure 10. Keypad height installation guideline.
DISPLAY
USING A NEW CONSTRUCTION BRACKET
Faceplate
Contact Touch Screen and Display Keypad:
1. Connect a properly configured CAT-5 cable to the
T568A system terminal on the back of the interface.
2. Install interface to construction bracket (IntelliControl
ICS Part #FG01192; not included) as shown.
CAT-5 Cable
3. Finish with appropriate color trim plate.
Single Keypad:
1. Connect a properly configured CAT-5 cable to the
system terminal on the back of the keypad.
Decora
Style Insert
1 Gang
Low
Voltage
Box
iPOD
SIRIUS
ROCK
2. Install keypad to low voltage electrical box as shown
using included hardware.
3. Finish with appropriate color faceplate.
WARNING: Do not mount the keypad, or IR sensor if
used, in the same electrical box as 110V AC devices.
This is a violation of electrical code in some areas.
CLASSICL
XM
AM/FM
JAZZ
BLUES
PREV
NEXT
VOL –
VOL +
OFF
MUTE
SINGLE
Faceplate
55
SYSTEM SETTINGS
CONTACT
SYSTEM SETTINGS ACCESS
0''
13&7
70-
/&95
70-
The “System Settings menu” appears.
Page
Back
.65&
Key.
to go back to “System Settings menu” or
Touch
wait 10 seconds. The “Now Playing” screen will automatically appear.
PAGE/DOORBELL
Page
Key.
System Settings
Back
Touch the
Soft Key to go back to “System
Settings menu” or wait 10 seconds. The “Now Playing”
screen will automatically appear.
Audio Settings
Paging/Doorbell
Sleep Timer
Alarm Clock
AUDIO SETTINGS: TREBLE/BASE/BALANCE
Clock Setting
Page
Key.
Touch the
Back
[Paging/Doorbell]
Page
button.
Paging/Doorbell
System Settings
Audio Settings
Paging/Doorbell
Use the [
Sleep Timer
this Zone is On]
]
or [
] keys to select [Always in this Zone], [Only if
or [Never in this Zone].
Alarm Clock
Paging/Doorbell
Clock Setting
Never in this Zone
Touch the
[Audio Settings]
button.
Audio Settings
If [Always in this Zone] is selected, then touch the [+] or [–]
keys area to increase or decrease the [Page Volume].
The “Audio Settings” screen appears.
Paging/Doorbell
Always in this Zone
Page Volume
–
+
Back
Touch the [+] or [–] keys area to increase or decrease the
treble, bass or balance levels.
56
SYSTEM SETTINGS
CONTACT
SLEEP TIMER
ALARM CLOCK
Touch the
(CONTINUED)
[Sleep Timer]
Key.
button.
Touch the
[Alarm Clock]
Sleep Timer
Use the
[ ]
or
[ ]
Key.
button.
Alarm Clock
keys to select
[Sleep Timer On]
or
[Sleep
Timer Off] .
Use the
[ ]
or
[ ]
keys to select
[Alarm Clock On]
or
[Alarm Clock Off] .
Alarm is On
Sleep Timer
If [Alarm Clock On] is selected, then touch the hour button,
minutes button and AM/PM button to set the alarm clock.
Sleep Timer is On
Time: 30 minutes
–
+
Alarm Clock
All Zones
Page
Back
Alarm is On
6 : 00 AM
Page
If [Sleep Timer On] is selected, then touch the [+] or [–]
keys area to increase or decrease the length of time.
Use the
Zones] .
[ ]
or
[ ]
keys to select
[This Zone Only]
or
[All
CLOCK SETTING
Sirius
Back
Use the [ ] or [ ] keys to select the source you want to
wake up to (i.e., SIRIUS).
Key.
Touch the [Clock Setting] button.
Clock Setting
Touch the hour, minutes and AM/PM button to set the clock.
Clock Setting
appears.
Press the [Page
Turn On Volume
] Soft Key to move
press the SELECT
Key to proceed.
Press the Cursor
Key to move
from [Backlight On] time to [Bat-
12 : 00 AM
tery Save].
Use the Cursor
Touch the
button when complete.
deep sleep mode.
Page
Back
Page
Display Settings
Contrast 65%
or
Key to set the
Back
System Settings
Display Settings
Battery save
after 5 minutes
Back
network and doesn’t display metadata until picked up.
57
SYSTEM SETTINGS
CONTACT
(CONTINUED)
DISPLAY SETTINGS/BACKLIGHT
CLEANING THE TOUCH SCREEN
Key.
Touch the
button.
[Display Settings]
Key.
Touch the
Display Settings
[Clean Me Screen]
button.
Clean Me Screen
Touch the
[+]
or [–] keys to increase or decrease the
length of time.
Clean the screen using a soft cloth and a mild dish
detergent.
[Backlight On]
System Settings
Display Settings
Display Settings
Back Light On: 30 seconds
–
+
Turn On Volume
Key Beep Volume: 5
–
Clean Me Screen
+
Color Scheme
Standard
Martha
Safari
Space
Page
Back
Touch the
[+]
or
[–]
keys to increase or decrease the
[Key
Beep Volume] .
Touch a button under
scheme.
[Color Scheme]
Key when
to change the color
Clean Me
This display is inactive for cleaning.
Reactivate the display by pressing the
Niles Logo button.
TURN ON VOLUME
[Turn On Volume]
Page
Press the Niles System Setting
complete.
NOTE: For show homes, always leave the backlight “ON“
Touch the
Back
Key.
button.
''
13&7
/&95
70-
70-
.
Turn On Volume
Use the
[ ]
or
[ ]
keys to select
[Last Used Volume]
[Default Volume] .
or
Turn On Volume
Touch the [+] or [–] keys to
increase or decrease the
[Preset Volume] .
Default Turn On Volume
Preset Volume: 49%
–
+
Back
58
SYSTEM SETTINGS
DISPLAY AND iREMOTE ®
AUDIO SETTINGS: TREBLE/BASE/BALANCE
PAGE/DOORBELL
Display:
0''
13&7
/&95
70-
70-
;POF
.65&
Key.
&OUFS
System Settings
0''
Audio Settings
.65&
Paging/Doorbell
iRemote:
Sleep Timer
Alarm Clock
J3&.05&
Clock Setting
¥
Page
Back
Page
Key.
Use the Cursor
or
Key to highlight the
settings from the list and press the
Key.
[Paging/Doorbell]
SELECT
System Settings
Audio Settings
Paging/Doorbell
Paging/Doorbell
Sleep Timer
Never in this Zone
Alarm Clock
Clock Setting
Page
Back
Page
or
[Audio Settings] from the list and press the
SELECT
Key.
Back
Use the Cursor
Use the Cursor
or
Key to select [Always in this
Zone] , [Only if this Zone is On] or [Never in this Zone] .
Audio Settings
Treble: 3
Paging/Doorbell
Bass: 2
Only if Zone is On
Balance
Page Volume: 80%
Back
Back
Press the Cursor
[Bass] to [Balance] .
Use the Cursor
Key to move from
or
[Treble]
to
Key to set the level.
Press [Back] to go back to “System Settings menu” or
wait 10 seconds. The “Now Playing” screen will automatically appear.
Press the Cursor
Volume] .
Use the Cursor
Key to highlight
or
[Page
Key to adjust the level.
59
SYSTEM SETTINGS
SLEEP TIMER
(CONTINUED)
CLOCK SETTING
Key.
System Settings
System Settings
Audio Settings
Audio Settings
Paging/Doorbell
Paging/Doorbell
Sleep Timer
Sleep Timer
Alarm Clock
Alarm Clock
Clock Setting
Clock Setting
Page
Back
Key.
Page
Page
Use the Cursor
or
[Sleep Timer] and press SELECT
Key.
Back
Page
Use the Cursor
or
Key to highlight [Clock
Setting] from the list and press the SELECT
Key.
Sleep Timer
Clock Setting
Sleep Timer Off
8 : 2 0 PM
Use the Cursor
or
or [Sleep Timer Off] .
Key to select
[Sleep Timer On]
Back
Sleep Timer
Use the Cursor
Sleep Timer On
or
Key to adjust the hours.
30 minutes
Press the Cursor
This Zone Only
Key to highlight minutes.
Back
Press the Cursor
of time.
Use the Cursor
of time.
Key to highlight the length
or
8 : 2 0 PM
Key to adjust the length
Back
Key to highlight
Press the Cursor
Use the Cursor
or [All Zones] .
Clock Setting
or
Key to select
[Zones] .
[This Zone Only]
Use the Cursor
or
Key to adjust the minutes.
60
SYSTEM SETTINGS
ALARM CLOCK
The “System Settings” menu appears.
Key.
(CONTINUED)
Key to highlight
Press the Cursor
Source] .
[Wake up
Alarm Clock
Alarm is On
System Settings
12:30 PM
Audio Settings
Paging/Doorbell
DSS
Sleep Timer
Alarm Clock
Back
Clock Setting
Page
Back
Page
Use the Cursor
or
[Alarm Clock] and press SELECT
Key.
Use the Cursor
or
Key to select the Source you
want to wake up to (i.e., DSS
).
Alarm Clock
Alarm is On
12:30 PM
appears.
Turn On Volume
DSS
Press the [Page
] Soft Key to move
Back
Use the Cursor
or
or [Alarm Clock Off] .
Key to select
System Settings
Display Settings
[Alarm Clock On]
press the SELECT
Key to proceed.
Press the Cursor
Key to move
from [Backlight On] time to [Bat-
Alarm Clock
Alarm is On
12:30 PM
tery Save].
Use the Cursor
Back
Page
Display Settings
Contrast 65%
or
Key to set the
deep sleep mode.
Page
Battery save
after 5 minutes
Back
DSS
Back
Press the Cursor
Use the Cursor
Key to highlight time.
or
Key to adjust the time.
61
SYSTEM SETTINGS
TURN ON VOLUME
DISPLAY SETTINGS (BACKLIGHT)
Press the [Page
of settings.
]
(CONTINUED)
Key.
Soft Key to move to the second screen
Press the [Page ] Soft Key to move to the second
screen of settings.
System Settings
System Settings
Display Settings
Display Settings
Turn On Volume
Turn On Volume
Page
Back
Key.
Page
Page
Highlight [Display Settings] and press the SELECT
Key to proceed.
Highlight
SELECT
Back
[Turn On Volume]
Page
from the list and press the
Key.
Display Settings
Turn On Volume
Contrast 65%
Last Used Volume
Back
Use the Cursor
or
Press the Cursor
time.
Key to set the
Back
[Contrast] .
Key to move from
[Contrast]
to
Use the Cursor
or
Key to select
Volume] or [Default Volume] .
Press the Cursor
[Backlight On]
Key to highlight
Display Settings
Turn On Volume
Contrast 65%
Default Volume
Volume 80%
Back
Back
Use the Cursor
or
backlight will be on.
Key to set the length of time the
Use the Cursor
volume level.
[Last Used
or
[Volume] .
Key to adjust the turn on
62
INSTALLER SETTINGS
These menus provide system diagnostic information
and allow configuration of ‘permanent’ system settings.
The now playing screen will return if no action is taken
for approximately 15-20 seconds.
1. Press & Hold Niles Logo Key for 5-10 seconds to
open ‘Installer Settings’ Menu
ZONE CONTROLLER
Select this to see the MAC ID and firmware version of
the GXR2 that the keypad is connected to (May be only
for development purpose).
TOUCH SCREEN
Selecting this disables the touch screen to allow for cleaning. To exit from this screen setting, press the Niles button.
CONTACT
MAC ID#
Select to confirm MAC ID# and Firmware version,
(Touch Screen, Display Keypad or iRemote ® )
MAX VOLUME
Adjust maximum zone volume and zone Page volume.
Maximum zone volume can help prevent damage to
the speakers and amplifier by setting a maximum output level well under the speakers power handling capability and amplifiers clipping level. Page volume sets an
undistorted paging level.
SOURCE LEVEL SETTINGS
Adjust GXR2 input levels to balance different source
audio output levels. This procedure requires that all
sources be on and playing. Radio stations should be
tuned to the same channel and Legacy Sources should
be playing program material with similar content. Using
similar or identical program material helps balance the
actual differences in output levels and not differences
in program material. With all sources playing, cycle
through the inputs to get a reference for which sources
are ‘louder’ and ‘softer’ than others.
INTERNAL IR SENSOR
DISPLAY
MAC ID#
(Touch Screen, Display Keypad or iRemote)
MAX VOLUME
the speakers and amplifier by setting a maximum output level well under the speakers power handling capability and amplifiers clipping level. Page volume sets an
undistorted paging level.
Select the option to enable or disable the internal built-in
IR sensor of the Contact. This is used when interference
from an IR source that cannot be removed from the area,
(A second IR sensor in the same area, Sunlight, Plasma
TV) is affecting the IR sensor built-in to the Contact.
63
INSTALLER SETTINGS
(CONTINUED)
Key. The “System Settings
menu” appears.
Press the [Page ] Soft Key to
move to the second screen of settings.
Highlight [Display Settings]
and press the SELECT
Key to
proceed.
iREMOTE®
MAC ID#
Press the Cursor
Key to
move from [Backlight On] time to
[Battery Save].
System Settings
Display Settings
Turn On Volume
Page
Back
Page
Display Settings
Contrast 65%
(Touch Screen, Display Keypad or iRemote)
MAX VOLUME
the speakers and amplifier by setting a maximum
output level well under the speakers power handling
capability and clipping level. Page volume sets an
undistorted paging level. Press the select button to
save the settings.
These settings are also adjustable with the IntelliFile 3
software.
The iRemote can also be used to adjust these levels
when a zone has the Single keypad.
Use the Cursor
or
Key
to set the length of time until the
iREMOTE goes into deep sleep
mode.
Battery save
after 5 minutes
Back
NOTE: Battery Save mode disconnects the iREMOTE from the
GXR2 network and doesn’t display metadata until picked up.
NETWORK CONFIGURATION
Settings to adjust the RF and Network channel for the
iRemote handheld unit. The base must be programmed
using the IntelliFile 3 software and a PC.
POWER DOWN
Setting allows for a software power switch to turn
on/off the iRemote handheld unit.
64
SPECIFICATIONS
GXR2
IM-iPOD
TM-XM
MODULAR MULTIZONE
RECEIVER
APPLE® IPOD®
I N T E G R AT I O N M O D U L E
X M ® S AT E L L I T E R A D I O
TUNER MODULE
FG01174
FG01176
FG01179
Power: 55 watts x 12 channels
Frequency Response:
26-20 kHz +/- 3 db
Signal to Noise: > = 85 db
Power Supply: AC 120V, 60Hz
Power Consumption: 1500 watts
maximum
Agency Certifications:
Class 2/SELV covering US, Canadian
and EU markets
Warranty: Two-year limited
Agency certifications:
Tested to UL/EN60065 for US,
Signal to Noise: >/= 85 dB
Power: Provided when installed
into GXR2 chassis
XM tuning range: 2332.5 to
2345 MHz
DIMENSIONS
Channels: Over 170 commercialfree pre-tuned
iPOD Module Card:
1-1/4” W x 3-3/4” H x 7-1/4” D
XM antenna connection:
50Ω SMB
Requires: XM Subscription
for content
DIMENSIONS
GXR2 Modular MultiZone
Receiver:
17-3/8” W x 5-3/4” H x 18” D
(including feet)
DIMENSIONS
XM Module Card:
1-1/4” W x 3-3/4” H x 7-1/4” D
65
SPECIFICATIONS
TM-SIRIUS
TM-AM/FM
IM-AUDIO
S I R I U S ® S AT E L L I T E
RADIO TUNER MODULE
AM/FM RADIO
TUNER MODULE
LEGACY AUDIO
FG01181
FG01175
FG01177
Class 2/SELV covering US, Canadian and EU markets
into IntelliControl ICS Modular
MultiZone Receiver chassis
Frequency Range:
AM 530 - 1710 kHz,
FM 87.7 - 107.9 MHz
into GXR2 chassis
SIRIUS tuning range: 2332.5 to
2345 MHz
AM SECTION
Antenna Impedance: 300 ohm
balanced
Video Sense Type: Composite
Video
Sensitivity @ S/N: 20dB 55dB
SIRIUS antenna connection:
50Ω SMB
Image Rejection: 33dB
Requires: SIRIUS Subscription
for content
FM SECTION
Antenna Impedance: 75 ohm
unbalanced
Channels: 150 commercial-free per
tuner
S/N ratio: 45dB
Sensitivity @ S/N: 30dB 6dB
max 12dB
DIMENSIONS
Image Rejection: 80dB
1 FM and 1 AM antenna (included)
TM-Sirius Module Card:
1-1/4” W x 3-3/4” Hx 7-1/4” D
Voltage Sync Input: 3-30V DC
DIMENSIONS
IM-Audio Module Card:
1-1/4” W x 3-3/4” H x 7-1/4” D
DIMENSIONS
TM-AM-/FM Module Card:
1-1/4” W x 3-3/4” H x 7-1/4” D
66
SPECIFICATIONS
TM-HD/R
IM-SERVER
HD RADIO™
TUNER MODULE
M E D I A S E R V E R / P L AY E R
FG01340
FG01339
Tested to UL/EN60065 for US, Canadian and EU
markets
Tested to UL/EN60065 for US, Canadian and EU
markets
Frequency Range:
AM 530 - 1710 kHz,
FM 87.5 - 108.1 MHz
Power: Provided when installed into GXR2 chassis
AM SECTION
Antenna Impedance: 1K-ohm AM Antenna
Input
Sensitivity @ S/N: 25dBUV@S/N 30DB 55dB
AM THD: .5% @-50Bm
DIMENSIONS
TM-AM-/FM Module Card:
1-1/4” W x 3-3/4” H x 7-1/4” D
FM SECTION
Antenna Impedance: 75 ohm FM Antenna
Input
Sensitivity @ S/N: 15dBUV@
S/N 30dB
FM THD: .5% @-66Bm
RS232G
BI-DIRECTIONAL GATEWAY
FG01265
DIMENSIONS
TM-HD/R Module Card:
1-1/4" W x 3-3/4" H x 7-1/4" D
Power: 12VDC @ 90mA (powered through
Intellicontrol ICS wiring)
Note: IM-Audio card required for integration of
audio on a music server
DIMENSIONS
5-5/8" wide x 3-1/8" high x .7/8" deep
67
SPECIFICATIONS
SINGLE
DISPLAY
CONTACT
WA L L M O U N T S Y S T E M
C O N T R O L K E Y PA D
SYSTEM CONTROL
K E Y PA D W I T H L C D
D I S P L AY
SYSTEM CONTROL
K E Y PA D W I T H C O L O R
TOUCH SCREEN
FG01183
FG01185
Agency certifications: Class 2/
SELV covering US, Canadian and EU
markets
markets
Display: 3.5” High Resolution color
LCD with LED backlighting
FG01182
Master Keys: 8 Programmable,
configurable, backlit
Hard Keys: 6, backlit
Colors: Almond, black, bone, and
white Decora style inserts
markets
DIMENSIONS
Keypad: 5-3/4” W x 5-1/16” H x
2-1/2” D (based on mounting into
1⁄2” drywall)
DIMENSIONS
DIMENSIONS
Depth behind wall: 5” W x 41/4” H
Keypad: 1-3/4” W x 4” H x 15/8” D
Display: 2” High resolution backlit LCD
Depth behind wall: 1-1/8”
(based on mounting into 1/2” drywall)
Touch Screen: 5-3/4” W x 5-1/16”
H x 2-1/2” D
Retrofit wall cutout: 5” W x 41/4” H
Includes retrofit installation mounting
system
68
WARRANTY
LIMITED WARRANTY
Niles
Audio
Corporation
(“NILES”)
warrants
IntelliControl ® ICS product to the original purchaser to
be free of manufacturing defects in material and workmanship for a period of two years from date of purchase.
This Warranty is subject to the following additional conditions and limitations. The Warranty is void and inapplicable if NILES deems that the product has been used
or handled other than in accordance with the instructions provided by the manufacturer, including but not
limited to damage caused by accident, mishandling,
improper installation, abuse, negligence, or normal
wear and tear, or any defect caused by repair to the
product by anyone other than NILES or an authorized
NILES dealer.
To obtain warranty service, take the unit to the nearest
authorized NILES dealer, who will test the product and
if necessary, forward it to NILES for service. If there
are no authorized NILES dealers in your area, you must
write to NILES and include your name, address, model
and serial number of your unit, along with a brief
description of the problem. A factory Return Authorization Number will be sent to you. Do not return any unit
without first receiving written authorization and shipping instructions from NILES.
If the above conditions are met, the purchaser’s sole remedy shall be to return the product to NILES, in which case
NILES will repair or replace, at its sole option, the defective
product without charge for parts or labor. NILES will return
a unit repaired or replaced under warranty by shipping
same by its usual shipping method from the factory (only)
at its expense within the United States of America. There
are no other warranties, including without limitation, either
express or implied warranties of merchantability or fitness
for a particular purpose, with respect to the product.
Repair or replacement as provided under this warranty
is the exclusive remedy of the consumer/purchaser.
NILES shall not be responsible for any incidental or
consequential damages except to the extent provided
(or prohibited) by applicable law.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
For the name of your nearest authorized NILES dealer
contact: NILES AUDIO CORPORATION, P.O. BOX 160818
MIAMI, FLORIDA 33116-0818.
69
CONTACT INFORMATION
CUSTOMER SERVICE - TECHNICAL SUPPORT
BY PHONE (IN USA)
1-800 -BUY-HIFI (289-4434 )
BY PHONE (OUTSIDE USA)
1-305-238-4373
CUSTOMER SERVICE HOURS
8: 00 A M to 5:30 PM EST
TECHNICAL SUPPORT HOURS
8: 00 A M to 7: 00 PM EST
ON THE WEB
w w w.nilesaudio.com
EMAIL TECHNICAL SUPPORT
[email protected]
EMAIL FOR PRODUCT SUGGESTIONS
[email protected]
©2007 Niles Audio Corporation 12331 S.W. 130 Street, Miami, FL 33186 Tel: 800.289.4434 – www.nilesaudio.com – All rights reserved. Niles,
the Niles logos, IntelliControl, IntelliFile, and iREMOTE are registered trademarks of Niles Audio Corporation. All other trademarks are the property of their respective owners. Niles reserves the right to change specifications, descriptions and prices without notice. The technical and other
information contained herein is not intended to set forth all technical and other specifications. Designed and engineered in the USA. DS00511B
70

DS00511B-0 ICS Install-Setup.indd

Transcription

Similar documents

Adding RCA outputs to Mercedes Benz 2005 C240 W203 Audio20

vTuner Internet Radio Rapid Prototyping SDK USB

Bticino 334202 (5 Wire)

COMMERCIAL: Link Media - Everest Lounge, Harrow, UK

Halo by Parasound is the pinnacle of our 25 years` experience.

Step # 13 Open up TMPGEnc 4.0 Express and click on “Start a new

Sentry Wireless Headphone Instructions. Please use the

books1-2 label.ai

Cleveland Institute of Music

hear all entertainment the way it was intended.