Skid Steer Track Mounting Instructions

Watertown, WI 53094
877-260-3178 Toll-free
920-261-4549 FAX
E-mail: [email protected]
www.tracksplus.com
Skid Steer Track
Mounting Instructions
Use care! There is a risk of personal injury!
General Precautions
Refer to manufacturer’s instructions for raising and blocking the
boom when mounting and dismounting the tracks.
Tracks are not recommended for use with non-pneumatic tires.
Over-tightened tracks could damage tracks and/or skid steer.
Track-to-Tire fit, proper clearance, and safety shielding are the
customer’s responsibility.
If needed, please call our toll-free number
1-877-260-3178 for technical assistance.
Watertown, WI 53094
877-260-3178 Toll-free
920-261-4549 FAX
E-mail: [email protected]
www.tracksplus.com
© Copyright 2006 ComponentsPlus™ LLC
Tire Measurement Guide
Need the right
attachment to
finish the job?
Tire sizes can and do vary in
width and height, which can
cause tire damage or a
clearance problem. It is the
responsibility of the
customer to determine the
final fit, including clearances
and safety shielding.
Bale Spears
Forks
T-1000B Series
WT-102C Individual Pad
T-1200B Series
WT-104C Individual Pad
(Tire Tread Measurement of 11-1/4" & over)
Forks-Bale
Spear Combo
T-1200N Series
WT-103C Individual Pad
(Tire Tread Measurement up to 11-1/8")
T-1400B Series
WT-105C Individual Pad
Call us. We’ve got ‘em…
Watertown, WI 53094
877-260-3178 Toll-free
920-261-4549 FAX
E-mail: [email protected]
www.tracksplus.com
Parts List
Clearance Guide
Clearances can vary depending on the skid steer unit. Clearances
listed are recommendations only. It is the responsibility of the
customer to determine the final fit, including clearances and
safety shielding.
Clearance
between boom
and tire.
Track
Sag
(a, b, c, d)
2¼”
2¼”
3”
(f)
(e)
Key
(g)
Part Number
Description
Series
a
WT-102C
10” Steel Track Section
T-1000B steel series
b
WT-103C
12” Steel Track Section
T-1200N steel series
c
WT-104C
12” Steel Track Section
T-1200B steel series
d
WT-105C
14” Steel Track Section
T-1400B series
e
L-302C
6-1/8” Standard Link
All steel series
f
B-600
5/8” shoulder bolt
All series
g
N-701C
1/2” locknut
All series
Check for
clearance
between guard
and tire.
Track sag should
be kept between
1½” to 3”.
Check for clearance
between attachment
and tire.
Verify clearance
from side of
machine.
3”
Mounting Instructions
1. Your track is delivered with
minimal assembly required. In
some cases, your track may be
delivered in sections for ease in
handling. You may have to preassemble two sections to create a
track side. Be certain to verify
that each side of your preassembly has the same number of
track pads.
Disassembly Instructions
4. Drive the skid steer slowly
backward off the track.
2. Assemble the two components
for each side of the track,
fastening the links with the
bolts provided.
3. Lay the track out as pictured.
Remember - Verify that each
side has the same amount of
track pads!
4. Drive the skid steer onto the
track.
5. Repeat the procedure for the
other side. The track sections
are now ready to be rolled and
stored until they are re-installed.
Thank you for selecting...
Visit us at www.tracksplus.com!
Disassembly Instructions
1. Loosen and remove two bolts
from the assembly. Let the
track drop on the tires.
Mounting Instructions
5. Stop when the back wheel of
the skid steer passes the first
track pad.
6. Pull the front of the track over
the front wheel, taking up as
much slack as possible. Check
for clearance! Remember any modifications to the skid
steer that are necessary are
the responsibility of the
owner.
2. Replace the bolts and nuts to
the links to prevent misplacing
them.
3. Pull the track off the front tire
and lay it on the ground.
7. Attach a common come-along
(obtained at any hardware
store) to both ends of the
track. Ratchet any slack.
Mounting Instructions
8. Drive the skid steer forward to
bring the back of the track to
the middle position as shown.
9. Attach the come-along to the
underside of the track on both
ends through the bottom
opening of the second track.
This will provide the most even
joining of the track sections.
10. Ratchet the come-along until
the linkage lines up with the
mounting hole of the other
track. Insert the bolt and
hand tighten the locknut.
11. Loosen the come-along. Slide
the come-along to the far side
of the track. Ratchet the
come-along until the linkage
lines up with the mounting
hole. Insert the bolt and
hand tighten the locknut.
Mounting Instructions
12. Check to make sure there is
1½-3 inches of slack in the
track. Linkages of one or
more track pads can be
adjusted to obtain this
measurement. When you
obtain the desired amount of
slack, tighten bolts from the
assembly and any adjustment
made.
13. Release the come-along from
the track.
14. When finished, repeat the
procedure for the other side of
the skid steer. It may be timesaving to make any adjustments
before you begin, but it is possible
that wear and size may not be
identical.