BUGGYBOARD-BASIC™

De Eng Es Fr
It
Jp Nl
Pt
Gebrauchsanleitung
Owners manual
Manual del propietario
Manuel d’utilisation
Manuale utente
取扱説明書
from Lascal
Handleiding
Manual do proprietário
Modell / Model /Modelo / Modèle / Modelo:
BUGGYBOARD-BASIC™
BuggyBoard is a registered trademark and is protected by patent.
Control no.
ENGLISH
Dear customer, thank you for choosing a BuggyBoard-Basic™ from Lascal. We hope you will be satisfied with your purchase and will get good use for your BuggyBoard™.
WARNING!
Read these instructions carefully before use and keep for future reference.
Content............................................ 12
Wheels............................................. 13
Connectors....................................... 13
Arms............................................... 14
Connecting....................................... 16
Disconnecting................................... 16
When not in use................................ 17
Accessories....................................... 17
Cleaning and recycling....................... 17
Tests................................................ 18
Warnings.......................................... 18
Warranty.......................................... 18
Other Lascal products........................ 60
Contact information........................... 61
Product registration card.................... 63
- 11 -
English
IndexE
KEEP FOR FUTURE REFERENCE
CONTENT
81100 - 81106
81700
81300
81330
81301
81320
English
81310
81400
81150
81340
81321
81531
81520
81530
81500
81540
81560
81550
Part no.
Description
Preassembled part
Qty.
81100 - 81106
Platform
81150
Strap with hook
81300
Arm, left
x
1
81301
Arm, right
x
1
81310
Height adjustment screw
x
2
81320
Arm support, left
x
1
81321
Arm support, right
x
1
81330
Fixing plate
x
2
81340
Fixing screw
x
2
81400
Wheel
2
81500
Connector clasp
2
81520
Cotter pin
2
81530
Connector clamp short
2
81531
Connector clamp long
2
81540
Spacer
2
81550
Allen screw
2
81560
Allen key
1
81700
Owner manual
1
1
1
- 12 -
THE WHEELS
1. Attaching the wheels.
English
Place the platform (81100-81106) upside
down on a sturdy surface. Push the wheels
(81400) firmly into the wheel holders until
the wheels ‘click’ into place.
THE CONNECTORS
2. Choosing the correct clamp.
Measure the width of the upright tubing on
your stroller, which the connectors will be
attached (see 3). Use the table below to
chose the most suitable connector clamp
(81530/81531).
Ø 14 - 17mm
(Ø 0.55”- 0.67”)
20 - 25mm
(0.79”-0.98”)
Ø 18 - 21mm
(Ø 0.71”- 0.83”)
Ø 22 - 25mm
(Ø 0.86”- 0.98”)
- 13 -
24 - 26mm
(0.94”-1.02”)
Connector clamp long
(81531)
26 - 28mm
(1.02”-1.10”)
20 - 25mm
(0.79”-0.98”)
17 - 19mm
(0.67”-0.75”)
17 - 19mm
(0.67”-0.75”)
14 - 16mm
(0.55”-0.63”)
14 - 16mm
(0.55”-0.63”)
Connector clamp long
(81531) + Spacer
(81540)
26 - 28mm
(1.02”-1.10”)
Ø 26 - 28mm
(Ø 1.02”- 1.10”)
19 - 24mm
(0.75”-0.94”)
Connector clamp
(81530)
10 - 18mm
(0.39”-0.71”)
Connector clamp
(81530) + Spacer
(81540)
27 - 31mm
(1.06”-1.22”)
Max. 35 cm / 14 in.
Max. 35 cm / 14 in.
3. Positioning the connectors.
English
The connectors can be attached facing
forward or backwards. Position the connectors so that the arms (81300/81301), see
fig 6, will be able to reach the connectors
(maximum 35 cm (14 in.) above the ground).
Try to attach the connectors as low as possible on the stroller. Position the connectors so
that they do not interfere with the stroller’s
folding mechanism. The arms need to stay
clear of both the braking mechanisms and the
wheels of the stroller.
4. Attaching the connectors.
Push the connector clamp over the tubing
and insert the connector clasp (81500) into
the slot in the connector clamp.
1
2
5. Tightening the connectors.
5.
Screw the allen screw into the hole in the
connector clip and tighten with the allen key
(81560). The connectors must be firmly attached to the stroller. Check that the stroller
folds properly; if not, you may need to reposition the connectors.
2
1
THE ARMS
6. Rotating the arms forward.
A
Turn the platform onto its wheels.
B
(A) Use a coin to unscrew the height adjustment screws (81310) until they are just
released.
(B) Rotate the arms forward then tighten the
height adjustment screws.
- 14 -
7. Positioning the cotter pins (81520).
Measure the distance between the middle of
each of the connectors.
If the measured distance is between:
• 25-41 cm (10-16,1 in.)
Alt. A below.
• 41-51 cm (16-20 in.)
Alt. B below.
25 41 c
m
41 51 c
m
Alt. A
Alt. B
B
8. Choosing the right cotter pin hole.
A
1
2
3
There are three holes in each arm. To choose the hole that best suits your stroller, position the BuggyBoard™ as close as possible to
the back of your stroller, however do make
sure that your child can stand comfortably.
Once decided, screw the cotter pin into the
chosen cotter pin hole, tighten with a coin.
If the arms are too short to fit to your stroller, there is an ‘Extender Kit’ available as an
accessory, see fig 13.
- 15 -
English
Deciding the cotter pin direction.
CONNECTING
9-10. Connecting the BuggyBoard™.
Unscrew the fixing screws (81340). Adjust
the width of the arms and click the cotter
pins into the connectors, then tighten the
fixing screws. Ensure that the arms are an
equal distance from the centre of the board
and the cotter pins are locked in the connectors.
English
Leveling the platform.
Unlock the height adjustment screws
(81310) and rotate the platform until level.
Tighten the height adjustment screws.
Click
Click
DISCONNECTING
11. Disconnect the BuggyBoard™.
2
Push the red release buttons on the end
of the connector-bolt and pull the arms
upwards.
1
IMPORTANT !
The BuggyBoard™ must be disconnected from the stroller before
folding the stroller.
Do not fold the stroller with the
BuggyBoard™ attached
- 16 -
WHEN NOT IN USE
12. Hooking up the BuggyBoard™.
If the BuggyBoard™ is temporarily not in use,
it can be hooked up behind your stroller. Clip
the hook (80318) onto the platform and attach the strap to a higher point on your stroller.
English
”Click”
ACCESSORIES
13. Accessory: ”Extender Kit”
Item no.
To attach the BuggyBoard™ onto certain strollers an ‘Extender Kit’ may be needed. This
will lengthen each arm up to 6cm.
The ‘Extender Kit’ is sold as a pair of extenders.
14. Accessory: Extra Connector Kit
Item no.
If you want to attach the BuggyBoard™ to
another stroller/ pram without having to
remove the connectors each time, there is
an ‘Extra Connector Kit’ available. The ‘Extra
Connector Kit’ contains a pair of connectors.
The use of any accessories with the
BuggyBoard Basic that have not been
approved by the manufacturer is not
recommended.
CLEANING AND RECYCLING
Cleaning instructions: Use warm water with a soft cloth and a mild non-abrasive cleaning
fluid. All BuggyBoard™ parts and packaging are made from recyclable materials.
- 17 -
TESTS
We are committed to ensuring that this product is of the highest quality. The manufacturing process is regularly checked by both internal and external (TÜV) controllers.
Samples of parts and completed products are also taken out regularly for testing in
our own testing laboratory. The BuggyBoard™ is tested and approved SP Swedish
National Testing and Research Institute according to the relevant clauses in EN
1888:2003, clause 6.1.1 – 6.1.5, 7.2.2.6, 17.3, 18.2 and 21.4
English
WARNING
• Intended for use with only one child at a time from
approximately 2 years of age and with a maximum weight
of 20 kg (44 lb).
• Always keep your hands on the pram when your child
is standing on the BuggyBoard™. Never leave your child
unattended while he/she is standing on the BuggyBoard™.
• Make sure your child is always standing with both feet on
the anti-slip rear portion of the BuggyBoard™.
• Never use the stroller’s parking brake while your child is
standing on the BuggyBoard™.
• Before each use, check the connectors and tighten if
necessary.
• Do not use the BuggyBoard™ if any part is broken, torn
or missing.
• Never let children play with the BuggyBoard™.
WARRANTY
WARRANTY
Your BuggyBoard™ is warranted to be free from manufacturing defects for a period
of one year from date of purchase under normal use and in compliance with the operating instructions. This warranty extends only to the original retail purchaser and is
only valid when supplied with proof of purchase.
- 18 -