If it doesn`t smell, how can it work? M-Pro 7 uses a

M-Pro 7’s complete weapon maintenance system is designed to preserve weapon
integrity enhancing reliability, performance, service life and operator safety.
• Reduces weapon maintenance time by up to 80%
• Exceeds MILSPEC cleaning system requirements
• Commercially transportable world-wide
Approvals from Original Equipment Manufacturers (OEM) include but are not limited to,
Smith & Wesson, Berretta, Sig Sauer, ATK, Heckler & Koch, Colt and The Boeing Company.
Exterior
Always unload weapon prior to cleaning.
1. Spray M-Pro 7 Gun Cleaner on entire weapon
surface. (See FAQs for exceptions)
2. Let sit for 0 to 5 min. depending on fouling.
For best results, use M-Pro 7 Gun Cleaner first to
remove carbon which slows the copper etching
process. Once the top layer of carbon is removed,
use M-Pro 7 Copper Remover to dissolve welded
copper from the bore. To remove the multiple layers
of carbon and copper fouling, use both products as
directed below.
1. Swab bore with an M-Pro 7 Copper Remover
thoroughly soaked patch 2 to 3 times.
3. Reapply M-Pro 7 Gun Cleaner and remove
exterior carbon deposits with nylon bristle
brush.
2. Let sit for 5 to 10 minutes.
4. Wipe clean with a dry cloth, use cotton
swabs for hard-to-reach areas. Repeat
process as needed.
3. Scrub bore 2 to 3 times with bore brush.
Follow with a dry patch (a jag or double
patching is recommended).
Bore
1. Spray M-Pro 7 Gun Cleaner into the bore.
For small diameter bores, swab with a patch
thoroughly soaked with M-Pro 7 Gun Cleaner
to completely coat bore. (Bore can also be
plugged and filled with cleaner.)
2. Let sit for 0 to 5 minutes depending
on fouling.
3. Scrub entire bore 2 to 3 times with a metal
bore brush.
4. Swab bore with a dry cloth patch. A jag or
double patching is recommended for complete
bore contact.
5. Repeat process until patches are white or
light gray*.
Note: For Ultrasonic and/or Dip Applications see Specialized
Cleaning Applications
Test before use: M-Pro 7 Gun Cleaner and M-Pro 7 Bore
Gel are completely safe on factory finishes and have been
approved by major gun manufacturers. However, they can
instantly remove unprotected oil-based wood finishes,
water-based paint/finishes and some types of “cold bluing”.
* Light gray material does not have a significant impact on
accuracy. It will be removed in subsequent cleanings until
the patches consistently come out white.
STEP 2 - LUBRICATE
M-Pro 7 Gun Cleaner and M-Pro 7 Bore Gel
completely strip a weapon of oil or grease,
requiring a complete re-oil after cleaning.
1. Apply several drops of M-Pro 7 Gun Oil LPX to a
patch and swab bore 2 to 3 times to evenly
distribute.
4. Clean with M-Pro 7 Gun Cleaner as directed in
Deep Cleaning & Conditioning instructions.
5. Repeat both processes until patches are white
or light grey*.
Note: For bore use only. Keep M-Pro 7 Copper Remover
away from alloys or finishes containing copper (i.e. bronze
brushes, some aluminum alloys, some types of bluing).
Do not mix M-Pro 7 Copper Remover with other chemicals.
MILITARY STYLE FIELD MAINTENANCE
M-Pro 7 Gun Oil LPX can be used as a military
“CLP®” to keep a weapon in optimal working condition between deep cleaning and conditioning with
M-Pro 7 Gun Cleaner. Follow instructions for field
maintenance and lubrication below.
STEP 1 - CLEAN
SHOTGUNS
BORE CONDITIONING
M-Pro 7 Gun Cleaner removes lead and plastic shot
cup fouling, which can become embedded with
carbon. M-Pro 7 Gun Cleaner pulls the carbon out of
the plastic causing it to curl. The carbon and plastic
can then be removed with light brushing.
Continuous firing bonds carbon, lead and most
copper fouling to the bore metal in layers (see
illustration bottom left). No other cleaners can
completely remove these stubborn layers of carbon
and metal fouling. M-Pro 7 Gun Cleaner penetrates
under old layers of carbon, lead and copper fouling
removing them permanently. Once these layers are
removed, subsequent cleaning time and effort can
be reduced by up to 80% (depending on the degree
of build up). The key is dwell time and agitation.
The longer it dwells, the less agitation is required.
With the surface devoid of carbon deposits, fouling
does not adhere as easily and takes longer to build
up. Cleaning new weapons enhances this bore
conditioning.
LEAD FOULING REMOVAL
Lead fouling is bonded to the bore by carbon.
M-Pro 7 Gun Cleaner penetrates underneath the
lead and dissolves the carbon allowing the lead
to brush out. Spray M Pro 7 Gun Cleaner (or swab
M-Pro 7 Bore Gel) down the bore and wait 5 to 6
minutes. Take a dime or quarter size piece of stainless steel pot scrubber, wrap it around your metal
brush (this will not scratch the bore). Scrub bore
with brush and pot scrubber 5 or 6 times. Repeat
entire process until clean. To remove lead deposits
in compensators, use toothpicks and cotton swabs.
Subsequent lead removal will become easier with
regular use.
COPPER FOULING REMOVAL
At bullet velocities under 3,000 fps, copper is
bonded to the bore the same as lead and can
be removed with M-Pro 7 Gun Cleaner. At bullet
velocities greater than 3,000 fps, the copper can
become welded to the bore and must be “etched”
to remove. (See High Velocity Copper Removal.)
Exterior
1. Apply M-Pro 7 Gun Oil LPX to surface of
weapon as needed.
2. Brush to remove exterior carbon deposits with
nylon bristle brush.
3. Wipe clean with a dry cloth, use cotton
swabs for hard to reach areas. Repeat process
as needed.
Bore
1. Apply M-Pro 7 Gun Oil LPX to bore. For small
diameter bores, swab bore with a patch
thoroughly soaked with M-Pro 7 Gun Oil LPX to
completely coat bore.
2. Scrub 2 to 3 times with a metal bore brush.
2. Apply 1 to 2 drops of M-Pro 7 Gun Oil LPX
in/on any moving parts (i.e. bolts, triggers,
firing pins, springs, guide rods, etc.).
3. Swab bore with a dry cloth patch. A jag or
double patching is recommended for complete
bore contact.
3. Apply M-Pro 7 Gun Oil LPX to beginning of each
rail. Reassemble and cycle weapon 2 to 3
times to distribute.
4. Repeat process until patches are white or
light grey*.
4. Apply thin layer of M-Pro 7 Gun Oil LPX to
exterior weapon surfaces. (The low evaporation
rate of M-Pro 7 Gun Oil LPX will offer extended
rust protection depending on environment.)
5. Reassemble weapon.
SPECIALIZED CLEANING APPLICATIONS
STEP 2 – LUBRICATE
1. Apply 1 to 2 drops of M-Pro 7 Gun Oil LPX in/
on any moving parts (i.e. bolts, triggers, firing
pins, springs, guide rods, etc.).
ULTRASONIC OR DIP APPLICATIONS
Breakdown weapon, remove grips, stocks and
optics. Submerge parts in M-Pro 7 Gun Cleaner
for approx. 15 min. Bristle brush and wipe clean.
Repeat as necessary. Dry and re-oil thoroughly
(a full immersion in M-Pro 7 Gun Oil LPX is
recommended to protect internal mechanisms and
allow sufficient time to drain after immersion). Wipe
down. Reassemble. To reuse M-Pro 7 Gun Cleaner,
filter and keep in airtight container.
FIRING PIN CHAMBERS
Do not allow M-Pro 7 Gun Cleaner or M-Pro 7
Bore Gel to seep into the firing pin chamber. If
this occurs, place a drop or two of M-Pro 7 Gun Oil
LPX into the chamber. When submerging a weapon
completely in M Pro 7 Gun Cleaner, a full oil dip is
recommended.
(See Ultrasonic and Dip Tank Cleaning Applications.)
RUST PREVENTION
M-Pro 7 Gun Cleaner and M-Pro 7 Bore Gel completely strip a weapon of any oil or grease. Re-oil
entire weapon after cleaning. (See M-Pro 7 Deep
Cleaning & Conditioning Step 2 – Lubricate.)
FOR USE ON
M-Pro 7 Weapon Maintenance products are safe
to use on all knives, handguns, rifles, shotguns,
machine guns, grenade launchers, artillery pieces,
cannons, muzzle loaders, corrosive priming deposits, stainless, blued and nickel finishes, titanium,
aluminum, polycarbonate plastics (e.g. Smith &
Wesson’s SIGMA®, Glock®, Heckler & Koch® frames),
rubber, nylon and varnished/urethane woods.
MACHINE GUNS
Fully automatic weapons are more difficult to
maintain due to greater carbon buildup and higher
lubrication requirements. M-Pro 7 Gun Cleaner
cuts through carbon fouling for easy cleaning.
Traditional oils and military style CLP®s tend to
“flash” or burn off. In some cases involving larger
individual or crew served machine guns, operators
pour standard issue CLP® directly on the weapon
while firing to keep it lubricated. Combat users
report improved performance, smoother cycling and
reduced heat exchange when using M-Pro 7 Gun Oil
LPX.
To order M-Pro 7 products or for more information
Visit: www.MPro7.com
Call: 1.800.YES.4MP7
CLP® is a registered trademark of Armor Holdings
Email: [email protected]
FREQUENTLY ASKED QUESTIONS
Do I need to oil my weapon after I clean it?
Yes, M-Pro 7 Gun Cleaner will strip the weapon’s
surface of all oil and grease. Therefore, re-oiling with
M-Pro 7 Gun Oil LPX after cleaning is recommended.
CARBON & COPPER BUILD UP
Will M-Pro 7 Gun Cleaner harm an unprotected oil
finished stock?
No, M-Pro 7 Gun Cleaner will not damage the wood
of the stock. However, it will remove the oil from
unprotected wood (varnished wood or plastics do
not apply). After cleaning, simply re-oil the stock.
Will M-Pro 7 Gun Cleaner remove cosmoline and
other petroleum protectants?
Yes, M-Pro 7 Gun Cleaner will remove protectants.
Wipe off excess protectant, then liberally spray or
soak parts and stocks in M-Pro 7 Gun Cleaner and
wipe clean.
Lit No. 9105840806
Is M-Pro 7 safe on cold bluing, after-market or
non-factory finishes?
M-Pro 7 products are completely safe on
high quality after-market or non-factory finishes.
M-Pro 7 Cleaners will not harm the metal, but
may strip some weapons with less expensive
cold bluing finishes.
After cleaning with M-Pro 7 Gun Cleaner, why
does the bluing look whitish or faded?
When oil is stripped from a blued surface,
the clean metal can look faded, whitish or even
spotted. This is the actual appearance of the
metal and not caused by the cleaner. Apply a
thin coat of M-Pro 7 Gun Oil LPX to restore the
appearance of the bluing.
TRADITIONAL GUN CLEANERS
Traditional solvents
remove surface carbon fouling, but have
little to no effect on
embedded carbon
fouling.
Surface and embedded carbon fouling act as the
bond or glue for all types of fouling (lead, copper,
etc.). See the High Velocity Copper Removal
section for exceptions.
Will M-Pro 7 Gun Cleaner harm night sights?
No, M-Pro 7 products will not harm night
sights. However, some dot sights are covered
with water-based paint that may be removed.
Traditional copper
and lead solvents
etch the metal, but
have little effect on
embedded carbon
fouling.
Pictured is a cylinder face of a Smith & Wesson® .357
magnum revolver cleaned multiple times with several
popular gun cleaning brands.
TRADITIONAL GUN CLEANERS
How often should my weapon be cleaned?
Most weapon manufacturers recommend cleaning
every time it is fired. This helps to maintain weapon
reliability and extend its service life. Weapons are
designed to shoot clean. Make sure all weapons are
unloaded before cleaning. Everyday “carry firearms”
should be cleaned weekly.
What type of bore brush should I use?
The standard bronze bristle bore brush is more than
adequate for general cleaning. Stainless steel is
recommended for stubborn fouling removal. Nylon
brushes are not effective on embedded fouling.
The remaining visual
carbon “staining” is
the same embedded
carbon in the bore
that acts as a bond
for surface carbon
and metal fouling.
This side was then
cleaned with M-Pro 7
Gun Cleaner.
M-PRO 7 GUN CLEANER
M-PRO 7 COPPER REMOVER
M-Pro7 Gun Cleaner is the only cleaner on the
market that removes the embedded carbon
fouling layer allowing the embedded metal
fouling to easily brush out.
M-Pro 7 Copper Remover then dissolves or
“etches” welded copper leaving a clean bore
surface when used in conjunction with M-Pro 7
Gun Cleaner (see detailed cleaning section).
COMBAT PROVEN
If it doesn’t smell, how can it work?
M-Pro 7 uses a unique blend of chemical
technologies containing corrosion inhibitors and
surfactants with a non-toxic solvent base to provide
superior cleaning without the intense smell. Even
on a “clean” weapon, M-Pro 7 Gun Cleaner will
remove additional carbon left behind in the bore
by other gun cleaning products.
FACE TO FACE COMPARISON
M-PRO 7 GUN CLEANER
STEP 1-CLEAN
HIGH VELOCITY COPPER REMOVAL
COMBAT PROVEN
COMBAT PROVEN
DEEP CLEANING & CONDITIONING
© Pantheon Enterprises 2011
GUN OIL LPX
Combat Proven Lubricant Protectant (with Cleaner)
More than just gun oil, LPX is the next generation of Lubricant
and Protectant for advanced military and law enforcement style
handheld and crew-served weaponry used in extreme environment
operations.
The highest possible protection against wear, humidity, and
moisture, including salt water; leaves a long-lasting film that repels
dust/dirt and will not evaporate – excellent for long-term storage.
• Replaces and outperforms traditional gun oils, CLPs and dry
lubes
• Combines high quality synthetic oils and LPX additives
• Unique technology is resistant to evaporation and gumming
• Formulated from technology with the lowest known friction
coefficient
• Cleans surface fouling without the use of solvents
• Meets requirements of MIL-L-63460 revision “E”
• Max temperature range (-85°F to 462°F)
M-Pro 7 Gun Oil LPX contains a cleaning agent that repels dust/
dirt and can be used as a “cleaner” to remove surface carbon
in the field. M-Pro 7 Gun Cleaner should be used for periodic
deep cleaning and removal of embedded fouling (Garrison Level
Cleaning).
Our basic CLP wasn’t working well. After a fire fight in
Afghanistan where my gunner’s M-240B jammed, he
used M-Pro 7. It didn’t just fire well - it purred.
SGT Andrew M. - 82nd Airborne Division
To order M-Pro 7 products or for more information: Visit: www.MPro7.com • Call: 1.800.YES.4MP7 • M-Pro 7 products are odorless, non-toxic, non-hazardous, biodegradable, non-flammable and environmentally safe.
Rock McMillan - McMillan Bros. Sniper Rifles
We have tried every product on the market and
without question, M-Pro 7 is the very best product
available for cleaning firearms - period.
• Up to 4x faster than ammonia based cleaners
• Improves accuracy and reliability
• Dissolves all copper fouling
• Conditions to reduce future fouling
• Safe on bore steel (for use inside bore only)
• Ammonia & odor free
Eliminates copper fouling without the use of ammonia or other
toxic chemicals.
COPPER REMOVER
Breck Fergusen - SSG. MOARN R&R NCO
I have not seen M-Pro 7’s equal when it comes
to carbon removal. The amount of time spent on
cleaning weapons was cut by more than half.
An alternative to traditional spray cleaners with all the features of M-Pro 7 Gun Cleaner.
*Also available: 4 oz. M-Pro 7 Bore Gel.
For Ultrasonic and/or Dip Applications:
(See Specialized Cleaning Applications).
• Significantly cuts cleaning time
• Improves accuracy and reliability
• Conditions to reduce future fouling
• Removes carbon, lead and most copper fouling
Vital to maintaining weapon reliability and performance by
removing layers of fouling, embedded carbon and conditioning the
bore to help prevent future build-up.
GUN CLEANER
WEAPON MAINTENANCE
COMBAT PROVEN
• Commercially transportable world-wide
Approvals from Original Equipment Manufacturers (OEM) include but are not limited to,
Smith & Wesson, Berretta, Sig Sauer, ATK, Heckler & Koch, Colt and The Boeing Company.
• Exceeds MILSPEC cleaning system requirements
• Reduces weapon maintenance time by up to 80%
M-Pro 7’s complete weapon maintenance system is designed to preserve weapon
integrity enhancing reliability, performance, service life and operator safety.
What drives the M-Pro 7 Team are the hundreds of letters and
e-mails we receive from
soldiers, lawPROVEN
enforcement officers and their
COMBAT
families. Many of these letters are passionate testimonials about
the lives M-Pro7 has saved because a weapon worked flawlessly and
consistently. Too often these letters ask for our help because their
current weapon cleaners or supply chain can’t get it done.
Rest assured that we will continue to make products that do their job
every time so that you can safely do yours. We are committed to those
serving our country and communities.
We are dedicated to the men and women who serve our country
– donating thousands of bottles, kits and sundries through
adoptasniper.org, anysoldier.com, law enforcement agencies,
academies, and training facilities.
We spend thousands of man-hours wading through the United States
Government bureaucracy advocating for reform of the outdated military
weapon cleaning specifications and thousands of dollars on testing
to ensure soldiers and law enforcement officers will eventually have
access to the best technology.
We are reading the letters – keep them coming. We thank you sincerely
for your sacrifices.
Respectfully,
The M-Pro 7 Team
800-YES-4-MP7
www.MPRO7.com
PRODUCT GUIDE
MPRO7.COM
UNIVERSAL SOFT SIDED CLEANING KIT
The Original M-Pro 7 kit contains everything needed to maintain all weapons
from .22 caliber to 12 gauge shotgun.
UNIVERSAL CLEANING KIT
M-Pro 7 TACTICAL
ADVANCED SMALL ARMS CLEANING KIT w/MUT
This kit contains everything needed to properly maintain military style weapons
in the field and in garrison. Each item was specifically requested by soldiers
to simplify and speed-up their current maintenance process. The Leatherman
MUT is the first multi-tool that functions as both a tactical and practical tool for
military, LE, or civilian shooters multiple areas on the tool threaded for cleaning
rods and brushes and screwdriver bits sized for standard military and civilian
sighting adjustment work.
*Advanced Small Arms Cleaning Kit contains everything in the kit above, except the
Leatherman MUT.
9MM PISTOL CLEANING KIT
M-Pro 7 BORESNAKES
This kit contains everything needed to maintain all weapons from .22 caliber
to 12 gauge shotgun. Comes in a soft nylon pouch.
5.56MM & 7.62MM ASSAULT RIFLE CLEANING KIT
The first M-Pro 7 BoreSnake kit for the most popular military and law enforcement
pistol caliber. Also works on .38 cal, .357, .380 cal pistols and revolvers.
The first M-Pro 7 BoreSnake kit for all M-16/AR-15 style rifles. Also works on
.22, .222, .223, .225, .22 hornet, .308, M2, 7.62x39, 30-30, .30-06, .300,
.303, .300 mag.
Quickly removes fouling with an embedded bronze brush and a swabbing
area 160 times larger than a standard patch. M-Pro 7 BoreSnakes come in
the following calibers: .22 cal pistol, 9mm, .38 cal, .357. .380 cal pistols and
revolvers, M-16, .22, .222, .223, .225, .22 hornet cal rifles, AR-15, .308, Nato,
M2, 7.62x39, 30-30, .30-06, .300, .303, .300 mag rifles, .338, .340, 8mm cal
rifle, .50 through .54 cal rifles, 12 gauge shotgun, 37mm/40mm grenade and
non-lethal weapon.
M-Pro 7 2oz Gun Cleaner
6850016003233
M-Pro 7 NSN Numbers:
M-Pro 7 Gun Oil LPX
2 oz spout
4 oz spout
1 Gallon
5 Gallon Pail
55 Gallon Drum
M-Pro 7 2oz Copper Remover
6850016003233
M-Pro 7 Bore Gel
4 oz spout
M-Pro 7 Copper Remover
2 oz spout
4 oz spout
1 Gallon
M-Pro 7 Products come in following sizes:
M-Pro 7 Gun Cleaner
2 oz spray
4 oz spray
8 oz spray
32 oz trigger spray
1 Gallon
5 Gallon Pail
55 Gallon Drum
M-Pro 7 4oz Gun Cleaner
6850016003251
To order M-Pro 7 products or for more information: Visit: www.MPro7.com • Call: 1.800.YES.4MP7 • M-Pro 7 products are odorless, non-toxic, non-hazardous, biodegradable, non-flammable and environmentally safe.