RFB MK6 Jetta Fog Light Kit

Transcription

7716 Wiles Rd.Coral Springs, FL 33067
www.uspmotorsports.com
Install instructions
RFB Lighting
What’s Included:
Tools Required:
(2) Fog Lights
T25 Torx
(2) Front Grills
Wire Cutters
Wire Harness
10mm Socket and Rachet
Headlight Switch
Headlight Switch
Hardware Kit
Composite Wedge Tool
01
RFB Lighting
1. Remove the lower front grills by
gently prying them outwards using the
composite wedge tool.
2. Route the supplied wire harness
through the hole located behind the
driver side head light.
02
RFB Lighting
3. Route the shorter lead with the blue
plug through the outer hole in the driver
side of the bumper (red arrow). Route the
longer lead with the blue plug through
the inner hole in the driver side of the
bumper (blue arrow).
4. The longer lead from step 3 will need
to be routed to the hole in the passenger
side of the front bumper. Route the lead
through the lower front grill and tuck
the wires into the bumper.
03
RFB Lighting
5. Ground the black wire from the passenger
side connector to the 10mm bolt securing
the washer fluid reservoir.
6. Connect the passenger side connector
to the passenger side fog light. The
passenger side fog light has a “R” on
the rear of the housing.
04
RFB Lighting
7. Install the fog light by inserting the
two locating tabs into the slots in the
bumper. Once the tabs are in place, secure
the fog light with a supplied T25 torx
screw.
8. Install the supplied fog light
grill. Starting from the outer side of
the bumper, pop the grill into place
making sure the locking tabs clip into
the bumper.
05
RFB Lighting
9. Connect the black wire from the driver
side connector to the 10mm nut located on
the frame rail.
10. Connect the driver side connector
to the driver side fog light. The driver side fog light has a “L” on the rear
of the housing.
06
RFB Lighting
11. Install the fog light by inserting the
two locating tabs into the slots in the
bumper. Once the tabs are in place, secure
the fog light with a supplied T25 torx
screw.
12. Install the
grill. Starting
the bumper, pop
making sure the
the bumper.
supplied fog light
from the outer side of
the grill into place
locking tabs clip into
07
RFB Lighting
13. Secure the relay on the wire harness to
the front of the fuse box located behind
the driver headlight.
14. Connect the red wire from the wire
harness to the positive terminal of the
battery and the brown wire to the negative
terminal.
08
RFB Lighting
15. Route the long yellow wire ending with
the silver terminal inside the car. Using
a fish tape or wire coat hanger to pull
the wire through is helpful.
a. If the vehicle is automatic you can
remove the insulation cut out next to
the brake pedal, make a small hole in the
grommet, and pull the yellow wire through.
b. If the vehicle is manual, you will need
to route the wire through the factory wire
harness grommet to the left of the clutch
pedal.
09
RFB Lighting
16. Remove the headlight switch by
pressing the switch in, turning
clock-wise, and then pulling
17. Route the yellow wire up to the
headlight switch harness.
10
RFB Lighting
18. Insert the yellow wire into position
8 of the headlight switch harness.
19. Connect the harness to the included
headlight switch and press the switch back
into place. If you currently have the RFB
automatic headlight conversion, the included
switch WILL NOT be used.
11
RFB Lighting
Enjoy Your Fog Lights!
12

RFB MK6 Jetta Fog Light Kit

Transcription

Similar documents

Lower Breitenbush Hot Springs Visioning

mini-fogger - MeterMall.com

build the ultimate rock star home

Rate Fairness Board Tyrone Jue, Communications Director

Spulen 2.0TSI Audi A4/A5 K04 Turbo Kit

2010 Camry Fog Lights - Sparks Toyota

getta jetta.indd

Math 335 Fall 2013, Exam 2 Key , , = 〈2 , + , −3 〉.

Cheers to our GoCu team from Korea having developed the