CLIP-IN CEILINGS

CLIP-IN CEILINGS
Metapan Metal Panel
Clip-In is a concealed system in which the
panels are clip fastened into a suspension grid
which is not exposed. The metal panels are
mounted into a primary suspension profile and
are supported by triangular shaped profiles of
galvanized steel. Tiles are square or rectangular
with chamfered or vertical edges.
Clip-in tiles are available in aluminium,
anodized aluminium (mirror look) or
galvanized steel. RAL 9001, 9002, 9003, 9006,
9010, 9016 and 7047 are the standard colors.
Other colors of RAL can be offered upon
request.
All Metapan products are tested according
to DIN EN 13964.
ADVANTAGES:
This system offers maximum safety,
stability, durability of the joints, maximum
resistance to earthquake loads and higher
torsional resistance.
Offers rapid installation and the tiles are
demountable with the help of a specific tool,
therefore allowing access for maintenance
openings.
Presents a smooth surface and provides
visual continuity.
One of the most suitable systems for
spaces demanding utmost hygiene like clinics,
operation rooms and such.
METAPAN ULTIMA®
CLIP-IN PANELS
Beveled edge
Square edge
Clip-In panels are electrostatically powder coated or coilcoated.
Electrostatic powder coat is epoxy polyester based organic coat with a minimum thickness
of 70 microns and a gloss of 25.
Coilcoated and stove enameled panels are coated with a polyester based organic coating
consisting of 5 microns of primer and 20 microns of top coat on the face and 5 microns of
service coat on the back.
Panels are manufactured from aluminum or galvanized steel or anodized aluminum
(mirror look). Material thickness is 0,6-0,8 mm for aluminum depending on the tile
dimensions and 0,50-0,60 mm for galvanised steel.
Aluminum panels are manufactured from aluminum alloy 3003 or alloy 5050.
Galvanized steel panels are manufactured from hot-dipped galvanized steel of grade
DX51 D +Z.
Openings necessary for lighting, sprinkler, loudspeaker and so forth can be factory
fabricated.
1
2
3
Standard Dimensions
Tiles
300
600
750
1000
300
x
x
Clip-In Profile
Height
Width
Length
600
x
750
x
900
x
x
1000
1200
x
x
1500
x
1800
x
x
2400
x
x
x
x
24 mm
34 mm
3600 mm
Carrier and Hanger Spans
Material Usage per Squaremeter
Item
Unit
30*30
60*60
Clip-In
Profile
mt
3.33
2.50
Hanger Set
pcs
0.70
0.80
Wall Angle
mt
1.50
0.70
Carrier
Splice
pcs
0.20
0.34
Coupling
Clip
pcs
2.00
1.40
1 60 - 120 cm
2 120 cm
3 Equal to the width of the tiles
METAPAN ULTIMA®
CLIP-IN SUSPENSION SYSTEM
SYSTEM COMPONENTS
CLIP-IN CARRIER
HANGER SYSTEM
HANGER
HOLD DOWN CLIP
PROFILE SPLICE
PERIMETER TRIMS
COUPLING CLIP ADJUSTMENT CLIP
D
TECHNICAL
INFORMATION
C
E
B
A
F
A
A
B,
E
C
Clip-In
Carrier
Rollformed from 0,55mm thick hot-dipped galvanized steel.
Standard Length:
3,6 m
Steel grade:
DX51D+Z
Coating thickness:
G90 (275gr/m²) or G60 (180gr/m²)
Tensile strength (N/mm2): min. 300
Elongation(%):
min. 22
Material subject to DIN EN 10327
Hanger /
Hanger
with
Adjustment
Manufactured from stainless steel. Available combined (B) or as a hanger
(C) and a double tension adjustment spring (F) seperately.
Material thickness:
0,60 mm
Stainless type:
301
Tensile strength (N/mm2): appr. 1455 (HRC: 45)
Material subject to DIN EN 10151
Hanger
Wire
Straightened and cut to length galvanized steel wire
Diameter:
4,00 mm (+-0,05mm)
Length:
60 cm - 400 cm
Tensile strength (kg/mm2): 40-55
Galvanization is subject to TS EN 10223
D
Perimeter
Trim
F
Coupling
Clip
Rollformed from 0,50mm thick hot-dipped galvanized steel. Either
coilcoated or eloctrostatically powder coated.
Standard Length:
3m
Steel grade:
DX51D+Z
Coating thickness:
Minimum 184gr/m²
Tensile strength (N/mm2): min. 300
Elongation(%):
min. 22
Material subject to DIN EN 10327
Manufactured from stainless steel
Material thickness:
0,60 mm
Stainless type:
301
Tensile strength (N/mm2): appr. 1455 (HRC: 45)
Material subject to DIN EN 10151
All suspension system components are classified as Class 1 in accordance with the provisions of EN 13501-1.
PERIMETER TRIM OPTIONS
22
20
12
9
20
19
34
K14
Z shaped angle
19
22
D14
C shaped angle
Perimeter detail with L shaped
profile
Perimeter detail with Z shaped
profile
K12
L shaped angle
Perimeter detail with C shaped
profile
PERFORATION OPTIONS AND ACOUSTIC PROPERTIES
4,2
5
5
4,2
2
1,8
1,5
5
5
5,5
17,32
8,4
8,4
20
5
2,
7
5,5
3
METAPAN suspended ceilings are characterised by high acoustic efficiency. Sound absorption is provided
by a 0.3 mm thick acoustic nonwoven fabric adhered to the perforated tile. When compared with the
conventional sound absorption agents like the mineral wool, nonwoven fabrics offer a number of benefits,
such as higher sound absorption, better look and superior flame retardancy. Moreover, being lighter and
particularly thinner than the conventional mats, nonwoven fabric reduces both shipping and inventory
costs and calls for less labor during installation.
The nonwoven material used by Metapan, namely R 6/60 FF, is manufactured by Royalin GmbH and made
of cellulose and glass fibers. It provides flame retardancy according to DIN 4102 B1. All Ultima product
groups have been tested for sound absorption in accordance with DIN EN 20 354 and the classified as per
DIN EN ISO 11 654. The textile is available in two standard colors of black and white, yet other colors
being offered upon request.
Note that depending on the requirements, Ultima metal panels are available with or without the
acoustical fabric.
2,5 mm hole
QUALITY ASSURANCE
Metapan has insisted on the business attitude of 'quality first and client
foremost' and proud to be EN ISO 9001:2000 certified by TUV Germany
and EN 13964 certified by TSE Turkey.
All components tested according to EN 13964.
METAPAN
Headquarters: Keresteciler Sanayi Sitesi 4.Cadde No:1 Saray / ANKARA
Tel: +90 (312) 815 20 56 Fax: +90 (312) 815 20 88
Istanbul Office: Mimarsinan Mah. Çavuþbaþý Cad. Ferhat Sk. No:11 Çekmeköy / Istanbul
Tel: +90 (216) 640 53 70 Fax: +90 (216) 640 53 73
www.metapan.com.tr
[email protected]