Duplo UD-300 Rotary Die Cutter Brochure

Transcription

Duplo UD-300 Rotary Die Cutter Brochure
UD-300 Die Cutter
UD-300
S P E C I F I C A T I O N S
SYSTEM TYPE
Rotary Magnetic Cylinder Die Cutter
PAPER SIZE (WxL)
Minimum: 8.267” x 11.693” (219 x 297 mm)
Maximum: 14.33” x 20.275” (364 x 515 mm)
PAPER THICKNESS
Minimum: 106 gsm
Maximum: 400 gsm
O n D em and D ie Cutter
With Separator:
Minimum: 200 gsm
SPEED
6,000 cycles per hour, handles sheets up to 14” x 20” at 3,000 sheets per hour
MEMORY
10 jobs
FEED SYSTEM
Air Suction, Top Belt Feeder
PAPER LOADING CAPACITY
Up to 7.875” (200 mm)
POWER
AC 110-115V 50/60 Hz. 5 Amps
DIMENSIONS (LxWxH)
81.10” x 27.17” x 46.85” (2,060 x 690 x 1,190 mm)
with conveyor: 127” x 27.17” x 46.85” ( 3,226 mm x 690 mm x 1,190 mm)
SUBSTRATES
Normal paper, coated paper, adhesive label
Production rates are based upon optimal conditions and may vary depending on stock and environmental conditions.
As part of our continuous product improvement program, specifications and descriptions are subject to change without notice.
WORKFLOW
1
2
3
J
O
K
E
R
J
O
K
E
R
J
O
K
E
R
J
O
K
E
R
create vector outline artwork for die
cut pieces via vector graphics software
4
send vector artwork to (die maker)
to create die
5
print full-bleed artwork sheets
finished round corner playing cards
JJ
OO
KK
EE
RR
JJ
OO
KK
EE
RR
JJ
OO
KK
EE
RR
JJ
OO
KK
EE
RR
J
optional separator and conveyor units
remove skeleton/waste portions
3050 S. Daimler Street, Santa Ana, CA 92705
finished die cut pieces
(949) 752-8222
(800) 255-1933
All rights reserved. No part of this document may be produced without permission of Duplo USA Corporation.
J
O
K
E
O
R
R
K
E
E
K
R
R
O
E
K
O
J
J
www.duplousa.com
0514AO
A P P L I C AT I O N S A M P L E S
O n D ema nd D ie Cutting for
With the ability to perform kiss cuts, the UD-300 Die Cutter can also create product labels of various shapes and sizes,
including irregular or round-corner. Flexible dies can be manufactured to cut the top layer of self-adhesive sheets.
Endless Possibilitie s.
Made for you by:
Emily Smith
Made for you by:
Emily Smith
!
!
CAUTION
!
Pinch point.
M o v i n g p a r t s be l o w .
K e e p h a n d s c l e a r.
!
WARNING
DANGER
WARNING
CAUTION
!
Pinch point.
M o v i n g p a r t s be l o w .
K e e p h a n d s c l e a r.
!
WARNING
!
Do not start, operate or
service machine until you
read operator’s manual.
Failure to do so couldresult
in serious injury.
WARNING
CAUTION
Pinch point.
Moving parts below.
K e e p h a n d s c l e a r.
!
WARNING
die cut pieces
printed sheet
Round
Corner
Cards
Create a variety of round corner cards at high speed production, from business cards to playing cards,
up to 1,250 business cards per minute.
CONTROL PANEL
The UD-300 minimizes set up times
and reduces make-readies. Job
programming and adjustments are all
made through the user-friendly control
panel. Adjustments can be made in
0.1mm increments for the width and
length direction of the sheet.
JJ
OO
KK
EE
RR
JJ
OO
KK
EE
RR
FEEDER
The UD-300 features a top, air-suction
feed system and fine tune adjustments
for air paper separation conveniently
located next to the tray.
MAGNETIC CYLINDER DIE
Flexible dies are both more economical
to manufacture and faster to deliver.
The flexible die is wrapped around a
rotary magnetic cylinder and can be
changed over in less than a minute.
OPTIONAL SEPARATOR/
CONVEYOR WITH PHOTOEYE SENSOR
A Separator and Conveyor Unit can be
installed in place of the stacker to remove
the skeleton/waste of each sheet. The
photo-eye sensor ensures finished pieces
are neatly stacked onto the conveyor to
ensure faster productivity.
J
O
JJ
OO
KK
EE
RR
Job programming and adjustments are all made through the
user-friendly touchscreen panel with individual buttons to
start and stop the operation. Adjustments can be made in
0.1mm increments for both the width and length direction of
the sheet. Once the job is set, the registration guides adjust
automatically. Sheets are loaded into the feeder and paper
guides ensure sheets are centered and fixed in position. The
UD-300 Die Cutter features a top, air suction feed system and
fine tune adjustments for air paper separation conveniently
located next to the tray.
CAUTION
Pinch point.
Moving parts below.
K e e p h a n d s c l e a r.
!
NEVER REACH
INTO MOVING
MACHINERY
K
E
J
O
K
E
R
EASY SET UP & QUICK JOB CHANGEOVERS
The UD-300 Die Cutter has been designed to minimize set up
times and reduce make-readies. Job changeovers are quick
and easy. Without any experience required, operators can
easily change over a die in less than a minute. The flexible die is
wrapped around a rotary magnetic cylinder, which holds the die
in complete registration.
WARNING
WARNING
!
Do not start, operate or
service machine until you
read operator’s manual.
Failure to do so couldresult
in serious injury.
J
O
K
E
R
FLEXIBLE DIES
Flexible dies are both more economical to manufacture and
faster to deliver compared to steel rule or solid rotary dies.
Ideal for today’s short-run and on demand needs, flexible
dies are custom-made and can be delivered in as soon as a
week, depending on application specifications. Flexible dies
are etched and made of magnetic steel to handle most type
of digital print applications. Thin in size, flexible dies require
minimal space to store.
!
Ideal for digital print providers in need of a short-run die cutting
solution, the UD-300 Die Cutter provides a cost-efficient solution
for producing custom-shaped pieces with faster job turnaround
and minimal set up times. Customers are recommended to keep
their most popular die plates in-house so when jobs are printed on
demand, they can also be finished on demand with no downtime.
!
Do not start, operate or
service machine until you
read operator’s manual.
Failure to do so couldresult
in serious injury.
DANGER
JJ
OO
KK
EE
RR
Compact in size and easy to use, the UD-300 Die Cutter provides
a cost-efficient solution with fast job changeover and set
up times – making it a great solution for the graphic arts and
packaging market!
DANGER
!
NEVER REACH
INTO MOVING
MACHINERY
!
NEVER REACH
INTO MOVING
MACHINERY
J
O
K
E
R
The UD-300 Die Cutter produces a variety of digital print and
packaging products such as custom-shaped brochures and
direct mailers, stationery, retail packages, labels, and folded
boxes in quantities as low as one. Designed for use with flexible
dies, the UD-300 performs multiple cuts, slits, slit-scores, kiss
cuts, perforations, and window punches for single or multipleup pieces on a wide range of paper stock up to 14” x 20” at 3,000
sheets per hour.
DURABLE, HIGH PRODUCTION EQUIPMENT
Compared to traditional flatbed die cutters and other rotary
die cutting solutions, the UD-300 is compact in size yet highly
durable and can easily be placed in any on demand environment.
WARNING
!
Do not start, operate or
service machine until you
read operator’s manual.
Failure to do so couldresult
in serious injury.
J
J
O
K
E
R
Create on-demand die cut products with the UD-300 Die Cutter!
DANGER
!
NEVER REACH
INTO MOVING
MACHINERY
Adhesives
printed sheet
die cut pieces
O
K
E
R
R
E
K
R
R
O
E
K
O
J
J
finished round corner playing cards
Expand your product line by offering on demand packaging products! Create pieces for clamshell packaging, add
window punches to neatly display products and apply retail hooks to make it easy for stores to hang.
printed sheet
die cut pieces
with retail products
Retail
Product
Packaging
finished & display-ready