ce type examination gertificate

ln application of the directive 89i686/EEG of 2'1 December 1989 concernlng the harmonisation of the
Member States legislation relative to personal protective equipment, Centexbel Notified body 0493
authorised by decree AV/OA23S/ST dated 94-05-25 of the Ministry of Employment and Labour has
issued
to:
Trital Safety bv
Mandenmakerstraat 41
3194 DA Hoogvliet
Nederland
CE TYPE EXAMINATION GERTIFICATE
Nr. 03107304
for:
The one or two piece suit FRACH-11
The personal protective equipment above mentioned satisfies the applicable essential safety
requirements of the Directive.
For the argumentation, the following standards are used:
EN 340:2003:
protective clothing - general requirements
EN 470-1.'1995:
protective clothing for welders
EN 531:í995:
protective clothing for industrialworkers exposed to heat (see annex)
EN '13034:2005:
protective clothing against liquid chemicals type PB [6] (see annex)
CLC TS 50354:2003.
electrical arc. test method for material and clothing (see annex)
prEN 1149-5:2006.
Protective Clothing - electrostatic properties (see annex)
The technical file is registered with numben 3382
, MSC
CENTEXBEL OENT
Technologiepark 7, BE-9052 Zwiinaardê lGentl
Tèt. +32 9 22O Ll 51
Fax +32 I 22O 19 55
e-màiL gentncentexbêl.be
BTW BE 0159 218
289 Fin. Rek. 210-o172?65'L5 IBAN
BÊ 11 210o 1729 6515
Annex to ceÉificate 031O73O4
The one or two piece suit FRACH-1 1 fulfil the requirements of EN 531:1995
to use the following pictogram:
{*/
EN
53,1
ABlCíDOEí
\-l
Annex to certificate 03107304
The one or two piece suit FRACH-1
í
fulfils the requirements of EN 13034:2005 Type PB [6]
to use the following pictogram:
For the fabric 4987 and 4965 of Utexbel:
class 6 for the abrasion resistance
class 2 for the tearing resistance
class 5 for the tensile strength
class 2 for the puncture resistance
class 3 for the repulsion of HzSOa 30%, NaOH 10% and HCI 36%
class 3 for the penetration of HzSO+ 30%, NaOH 10oÁ and HCI 36%
class X5for the seam strength
For the fabric BG 9500 of Ten Cate
:
class 6 for the abrasion resistance
class 2 for the tearing resistance
class 5 for the tensile strength
class 2 for the puncture resistance
class 3 for the repulsion of H2SO4 30% and NaOH 10%, o-Xyleen, Butan-1-ol
class 0 for the repulsion of o-Xyleen and Butan-1-ol
class 3 for the penetration of H2SO4 30% and NaOH 10%
class 0 for the penetration of o-Xyleen and Butan-1-ol
class 4 for the seam strength
For the fabric Tecasafe Static Gontrol XA 9001 of Ten Cate:
class 5 for the abrasion resistance
class 3 for the tearing resistance
class 5 for the tensile strength
class 3 for the puncture resistance
class 3 for the repulsion of H2SO4 30%, NaOl{ 10%, o-Xyleen, Butan-1-ol
class 3 for the penetration of l-l2SO4 30%, NaOH 10%, o-Xyleen, Butan-1-ol
class 5 for the seam strength
CENTEXBEL GENT
Technologiepark 7, BE-9052 Zwiinaarde íGêntl
Tel. +32
I
I
22o 11
51
19 55
ê-mail gêntGtentexbe[.be
56a +32
BTW BE 0159 21a
2A9
22O
Fin. Rek. 21O-0172965-15 IBAN BÊ 11 21O0 1729 6515
The fabric that is used for the outer
Annex to certificate 03107304
layer of the one or two piece suit FRACH-'1 í, is tested
according to CLC TS 50354:2003. During the test with 4kA during 0,5 s (class 1) and in which the
distance between the fabric and the electrodes is 30 cm, the following results were obtained:
After flame time < 5 s
No hole formation
The material does not melt further to the inner layer
The temperatures raise on the back of the sample is below the maximum allowed temperatures
raise according to Stoll/chianta (second-degree burn)
l-/
Annex to certificate 03107304
The one or two piece suit FRACH-1 '1 complies with the most recent understanding as written in
prÊN 1í49-5:2006
These requirements are as follows:
- The electrostatic dissipative clothing shall cover permanently all non complying materials
during normal use.
- lf the electrostatic dissipative protective clothing comprises multiple layers, the outermost
material shall meet the material requirements.
- Thin, non-dissipative attachments such as labels, reflective stripes, etc., are permitted
provided they are permanently attached so as to avoid significant separation between the
-
attachment and the electrostatic dissipative clothing.
Conductive parts (zippers, buttons ...) are permitted provided that they are properly
covered by the outermost material when the clothing is worn in flammable or explosive
atmospheres.
On homogenous materials the test is carried out according to EN 1149-1:2006.
On non-homogenous materials the test is carried out according to EN 1149-3:2004.
CENTEXBEL OENT
Technotogiepa
Ík 7, BÊ-9o52 zwiinaarde Í0entl
Tet. +32 I 22O 11
Psa
r32 I
51
22O 19 55
e-mail gentGcêntexbêl.be
BTw BE OL59 218 289 Fin. Rek. 21o-o172965-15 IBAN aÊ 11 210o 1729 6515