when receiving Laser numbered Anchor Seals (LM)

Models A-LM, AN-LM, ANR-LM,
AFN-LM, ARN-LM, ARNR-LM,
AWN-LM and AWNR-LM
when receiving
123
Opening sealed goods is too
much responsibility for just
one person. This should
always be shared, because in
case of any irregularities there
should be an on-the-spot
witness
Pull to test whether the seal is
really closed and not just
apparently closed.
EL
456
Suspicious marks, specially around the capsule
entrance, could mean tampering.
Check the seal number to see if it´s the same as
that on the document. The number on document
should have no erasures or corrections.
ELC
ELC
1234568
12345
68
To remove, cut thread well aways
from seal as to, if necessary, leave
it intact for later inspection.
Keep seal until checking is finished. Loss
of seal, when irregularities occur, makes
CAREFUL! the employees responsible.
Any
irregularity, call your security personnel. If the seal
should go to further inspection, the sealed
object must also follow it.
When all in order,
destroy used seal.
ELC
566
455
Also, the thread that
connects anchor to the
capsule should be intact,
because if broken, it could mean tampering.
ANCHORLMENG - 12/04
45
ELC
5
123
123
EL
C
Make sure that it is not a loose sealing.
1234
C
9
Laser numbered Anchor Seals (LM)
ELC Security Products
ELC is not responsible for the
incorrect use of this product.
www.elcsecurity.com
CNPJ: 73.323.404/0001-90 Insc. Est.: 84.604.259
8252 NW 30th Terrace • Miami, FL 33122 • USA
Phone: (305) 477-2303 • Fax: (305) 477-0186 • Toll Free: 800 377-3257 • E-mail: [email protected]
Laser numbered Anchor Seals (LM)
how to use
Models A-LM, AN-LM, ANR-LM,
AFN-LM, ARN-LM, ARNR-LM,
AWN-LM and AWNR-LM
when sealing
0 0 0 0 0 0 8 5
0
0
0
0
WIRE - SINGLE STRAND
STRING COTTON
WIRE - TWISTED
STRING PLASTIC
Should the connecting
thread break replace
with another seal.
A broken thread could
mean tampering.
METALLIC RIBBON OF ANY TYPE
1 mm
1 mm
Anchor Seal AFN-LM, AWN-LM, AWNR-LM,
ARN-LM and ARNR-LM - They came with their own
AR
C
N-
C
EL
LM
EL
10
00
00
10
4
00
AF
00
N-
et
001
00
00
(w
1
ire
2
M
(w
bo
ire
n)
)
)
4
Avoid sliding out of the thread!
12
0
NR
-L
10
56
C
65
ELC
0
g)
AW
EL
45
456
LM
C
EL
1
000
3
N-
0
C
rib
AR
N
(m R-L
10
et M
00
all
02
ic
1
rib
C
EL
str
in
AW
0
EL
456
Avoid loose sealings!
123
tic
0
ic
Pull the capsule
to test whether
the seal is
well closed.
n)
(p
las
1
all
3
Make sure the thread
is intact and without
knots or joints.
bo
LM
C
EL
(m
3456
123
string, wire or metallic ribbon.
ELC
12
PLASTIC SINGLE STRAND
01
1
0
ELC
234
8
1000001
1
ELC
0000010
000
00 0
1
ELC
LM
Make sure the
seal has no
defects.
ANR-LM
AN-LM
10
C
1
EL
000
A-
9
length of wire, string or ribbon up to 1 mm can be used.
7
If the closing operation
is made with no regard
CAREFUL! to the directions below,
the responsibility will fall on the
person who applied the seal
Anchor Seal A-LM, AN-LM and ANR-LM - Any
The thread must
be bent and
sealed at a point
that gives a
tightly adjusted
closure.
Models AWN-LM, AWNR-LM and AFN-LM with thin string
Strings and thin wires can be
All these models have a hole at the anchor of the seal, though
wound two or more times around
which must pass the thread, avoiding it to slide out.
anchor groove to avoid sliding out
after the closing of the seal.
The seal capsule
should not be
deformed due to an excess
of string around the anchor.
This prevents clousure, or results
in just a false or apparent sealing.
123
456
ELC
456
123
3
12
456
ELC
12
3
3
ELC
Important: All Anchor Seals LM are offered in mats with ten seals,
for an easy distribution and usage.
3
4
ELC
34 6
5