InnoEDGE – Embedded LPR ACAP version for Axis Cameras Version 1.3

Transcription

InnoEdge User Manual
InnoEDGE – Embedded LPR
User Manual
ACAP version for Axis Cameras
Version 1.3
INDEX
1.
2.
3.
4.
5.
PACKAGE INSTALLATION
Applicable Parameters
Graphical ROI representation
Algorithm output
Licensing the application
©InnoWare Technologies 2014
P2
p5
p6
p7
p8
www.innoware-tech.com
[email protected]
1. Package Installation:
- Connect to the axis setup page and select “Applications”
- The following page is displayed:
[email protected]
- Press “Browse” and select the correct installation file, placed in the “Setup” folder of
the installation CD1:
- use InnoEDGE_1_3_ARTPEC-4.eap for Artpec4 Axis cameras;
- use InnoEDGE_1_3_ARTPEC-3.eap for Artpec3 Axis cameras;
- Press “Upload Package” to upload the selected package into the Axis camera, then
the application InnoEdge will appear into the “Installed Applications” list:
- The application can run without a license, but with limited functionalities.
- Visit http://www.InnoEdge.com to purchase your license.
- Once installed the parameters of the application can be modified.
1
Contact Axis for exact camera specifications
[email protected]
In order to modify the parameters click on “InnoEdge Settings”, placed into the left
side of the “Application Packages” page.
- The following page is displayed:
[email protected]
2. Applicable parameters:
Parameter
Meaning
Values
IMAGERES
Resolution of the processed images.
This affects the number of frames InnoEdge
processes per second. On an Artpec4 camera
InnoEdge can process 4fps at a res of 640x480.
HMIN
DEFAULT: HALF_FRAME
Minimum height in pixels of detected plate
characters and numbers.
FULL_FRAME: InnoEdge uses main
stream res
HALF_FRAME: InnoEdge divides
main stream res by 2
QUARTER_FRAME: InnoEdge
divides the main stream res by 4
A value in the range 16-100.
Advised minimum height 20 pixels.
HMAX
DEFAULT: 20
Maximum height in pixels of detected plate
characters and numbers.
SERVERIP
DEFAULT: 40
IP Address of the server where the resulting
detections of InnoEdge engine are sent to.
A valid IP address
PORT
DEFAULT: 192.168.2.49
Port number used by the server to receive the
resulting detections from InnoEdge.
A valid port from 1 to 65000
PLATEBUFFERLEN
DEFAULT: 1234
Number of consecutive frames used by InnoEdge to A value in the range 1-30
start the recognition.
NUMMINREC
DEFAULT: 4
Number of same recognitions in the buffer that
define the final output.
SAMEPLATETIMEOUT
DEFAULT: 2
Number of seconds InnoEdge ignores plates when
equal to the last.
A value in the range 1-3600
USETEMPLATE
DEFAULT: 60
Allow the system to use country templates and
improve the recognition quality.
YES or NO
ROISTARTX
DEFAULT: YES
Start point of the ROI horizontal axis.
Number in 10th of % vs left side of image
ROIYSTARTY
DEFAULT: 0 – means start at left of image
Start point of the ROI vertical axis.
th
Number in 10 of % vs bottom of image.
ROIWIDTH
DEFAULT: 0 – means start at bottom of image
Horizontal width of the ROI.
th
Number in 10 of % vs ROISTARTX.
ROIHEIGHT
DEFAULT: 1000 – means entire image
Vertical height of the ROI.
Number in 10th of % vs ROISTARTY.
Advised maximum height 50 pixels.
Value >= HMIN.
Value <= PLATEBUFFERLEN.
ROISTARTX + ROIWIDTH <= 1000.
ROISTARTY + ROIHEIGHT <= 1000.
DEFAULT: 1000 – means entire image
[email protected]
3. Graphical representation of ROI set-up:
It is recommended to define the ROI to measure approximately 640x480 pixels.
This should be calculated versus the total image settings.
Example:
With an image resolution of 1280x720
Set ROISTARTX at 250
Set ROIWIDTH to 500
Set ROISTARTY at 250
Set ROIHEIGHT at 500
This means ROI is defined from ¼ of the left side and spans half the image.
Likewise, the ROI starts from ¼ of the bottom and spans half the height.
Thus the ROI measures 640x360 pixels.
[email protected]
4. Algorithm output:
MJPEG STREAMING:
An MJPEG Stream delivering the detection results is directly available.
In order to show the stream open a web browser and go to
www.IPCAMERA/local/innoedge/analyze.cgi
When a plate is detected, the result of the detection is placed on the top-left side of
the image.
This streaming is available also if the application is not licensed.
SERVER2:
Innoedge can send the result of a recognition to via network to a socket
server/listener application.
The port on which InnoEdge and the external application communicate can be
defined in the InnoEdge application settings (see “Applicable parameters”).
When InnoEdge detects a new plate, it sends the following string to the server:
<INNOEDGE>
<PLATE>DETECTED_PLATE<\PLATE>
<DATE>DETECTION_TIME<\DATE>
<CONF>PLATE_CONFIDENCE<\CONF>
<HCAR>PLATE_HCAR<\HCAR>
<\INNOEDGE>
wherein:
DETECTED_PLATE represents the detected plate, e.g. “AB123CD”
DETECTION_TIME represents the time stamp, in format DD-MM-YY HH:MM:SS
PLATE_CONFIDENCE represents the quality of the recognition, in the range 0-100
PLATE_HCAR represents the height of detected plate characters.
2
This functionality is available only for licensed applications
[email protected]
5. Licensing the application:
In order to license the application go to the setup page and select “License” in the
InnoEdge settings form.
The following page is displayed:
Press “Select” and navigate in order to select the license file, provided by InnoWare.
Press “Install” to install the license.
[email protected]
Upon completion the following page is displayed:
In the overview pane “Application Package” “YES” will appear in the “License
Installed” field.
[email protected]

InnoEDGE – Embedded LPR ACAP version for Axis Cameras Version 1.3

Transcription

Similar documents

Varnica - Dantex

ALTO PART # 112756 INSTALLATION INSTRUCTIONS Ford CD4E

Giuliana Rancic - Stephanie Stephens

A Global Guide to Business Etiquette

Unipres USA Portland, TN Case Study.indd

Tech Note O Subaru Impreza WRX, Liberty/Legacy (Turbo

BannerMASTER Bracket Installation Instructions 1 2 3 4 5 6 7 8

eo WideRailInstruc.indd

User Manual of how to inquire about Traffic Fines by the Mobile