to view AMP design guidebook

Design Handbook
Scorria Designs
Smooth
Corduroy
Fine Streaks
Anay Finish
Cauliflower
Scraped
Autumn
Bubbles
Brick
Lace
Ripples
Sandstorm
Swirled
Coral
Waves
Wide Streaks
SMOOTH
SMOOTH
1
Trowel on a first coat to cover the
surface.
2
Apply a light coating of ALTAMIRA on
trowel.
3
Spread it lightly in a circular motion
while the paint is still fresh.
CORDUROY
CORDUROY
1
2
3
Trowel on a coat to cover the surface.
Apply a light coating using a trowel
with a comb template (notched
trowel).
Comb the trowel on the surface until
the desired design is achieved.
SWIRLED
SWIRLED
1 Trowel on a coat to cover the surface.
2
After the mortar has slightly stiffened,
apply second coat using an arcing
motion. Allow the resulting pattern to
remain before applying another
overlapping arced stroke.
WAVES
WAVES
1 Trowel on a first coat to cover the
surface.
2
Using the tip of your trowel, draw the
marks randomly.
FINE STREAKS
FINE STREAKS
1
Trowel on a first coat to cover the
surface.
2
After covering the surface,
lightly press the trowel to the
surface and drag it sideways.
ANAY FINISH
ANAY FINISH
1
Trowel on a first, thin coat to
completely cover the surface.
2
Apply a light coating of ALTAMIRA on
the trowel bottom.
3
Dab it onto the coated surface and pull.
4
Let the surface dry for
approximately 45 minutes
5
Knockdown the surface using trowel.
CAULIFLOWER
CAULIFLOWER
1 Trowel on a coat to cover the surface.
2
3
Then hold the upper portion of the
walis ting-ting and stamp it onto the
surface and then pull to give the
desired pattern
Allow the mortar to stiffen then knock
down the design with a float.
SCRAPED
SCRAPED
1
Trowel on a first thick coat to cover
the surface.
2
Use a walis tingting to create vertical
markings on the coated surface.
AUTUMN
AUTUMN
1 Trowel on a coat to cover the surface.
2
Using leaves with prominent designs,
make imprints on the soft mortar.
Carefully remove the leaves as the
mortar begins to stiffen
BUBBLES
BUBBLES
1 Trowel on a moderately thick coat to
cover the surface.
2
Allow the coat to slightly harden. Then
by using the opening of a drinking
glass or a plastic cup, make
intersecting circular prints.
BRICK
BRICK
1
2
Trowel on a coat of a cement paint
with a color contrasting that of the
paint to be used for “bricks.” Allow
the coat to fully dry and harden
before attaching/taping the brick
pattern guide.
Then trowel on a coat of the paint
designated for “bricks.”
3
Allow the first coat to dry.
4
Trowel on another coat.
5
Allow the coat to slightly dry
before peeling off the pattern
guide.
LACE
LACE
1
Trowel on a first coat to completely
cover the surface.
2
Using a wet sponge, dab it to the
coated surface to cover the sponge
bottom, press against the surface,
then pull.
3
Wait for the surface to set up
and dry (approximately 20
minutes), before knocking
down the texture with a
trowel
RIPPLES
RIPPLES
1 Trowel on a coat to cover the surface.
2
Allow the mortar to slightly dry then
lightly draw a brush across the
surface using a wavy path to give the
desired effect. Keep the bristles free
from mortar build-up by knocking the
brush head after each pass across the
surface
SANDSTORM
SANDSTORM
1
Trowel on a first thick coat to
cover the surface.
2
Use the specified roller, dab it to the
surface, and roll it hard to print the
design.
CORAL
CORAL
1
2
Trowel on a first thick coat to cover
the surface.
Use the specified roller, dab it to the
surface, and roll it hard to print the
design.
WIDE STREAKS
WIDE STREAKS
1
2
Trowel on a first thick coat to
cover the surface.
Use the specified roller, dab it to
the surface, and roll it hard to print
the design.
Ryolitte Designs
Ryolitte Designs
Sandblast
Dunes
Stencil
Sandblast
SANDBLAST
1
Apply on a base coat to cover the
rough surface with a nap roller.
2
Allow base coat to dry before applying
the second coat using the same roller.
Dunes
DUNES
1 Apply on a base coat to cover the
rough surface with a nap roller.
2
Allow the base coat to dry before
applying the second coat using the
design roller.
STENCIL
STENCIL
1 Apply on a base coat with a nap roller.
2
3
Allow the base coat to dry before
attaching the stencil guide. Make sure
that the guide is closely attached to
the surface
Apply on a paint of contrasting color
on the pattern guide using a stencil
brush or a bristle brush.