CEODEUX

Transcription

CEODEUX

CEODEUX
PURETEC
D
100
KEY FEA
TURES
FEATURES
• Freedom from seizure when used with corrosive gases - gas does not come into contact with
the valve operating mechanism
• Positive and effective operation - valve spindle is mechanically linked to the operating
handwheel, which only requires low closing torque
• Long life - valve spindle and seat are replaceable
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
• Low internal volume - this is particularly beneficial, when using the valve for hygroscopic,
corrosive or high purity gases, where inert gas purging may be necessary before opening or
after closing the valve
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Working pressure pmax
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-6 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
0,3
3,3 mm
Gas wetted materials
see table on backside
08-8
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
High pressure cylinder valves, packed needle stem
design, for high purity gases
D
CEODEUX
100
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
OPTIONS
Threading for flow restrictor
Dip tube connection
Valve body and handwheel PTFE coated
Gas wetted components electrochemically polished
Clean room assembling
Key operation
•
•
•
•
•
•
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Connections:
A: outlet
C: inlet
F: flow restrictor
G: dip tube
SERIES
D100 1
D100 3
D100 4
Body material
AlSI 303
Brass
AlSiBz
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
SEA
T SEAL
SEAT
PTFE 25%GF
PTFE Carbon filled
SPINDLE
AISI 303
Monel
SEA
T
SEAT
AISI 316L
AlSiBz
GAS DISTRIBUTION RING
AISI 303
AISI 316L
AISI 303
AISI 316L
Brass
AlSiBz
ROTAREX
Group
CEODEUX S.A. brand name PURETEC
24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
150
KEY FEA
TURES
FEATURES
• 3 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self centering Hastelloy© seal tip
• O-rings fitted into the gland to exclude humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
150 bar/2175 psi
-25°C up to + 65°C
at pmax
10-5 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
1,1
6 mm
08-8
High pressure cylinder valves, packed 3-piece sturdy stem
design, for corrosive technical gases
D
CEODEUX
150
PURETEC
Ø 65 mm
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
125 mm
OPTIONS
Attachement for 24 mm key operation
Dip tube connection
Valve body and gland assembly PTFE - coated
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• Type of gas
• Connections
• options and special features
SERIES
•
•
•
•
D150 1
D150 4
Body material
AlSI 303
Body material
AlSI 316L
AlSiBz
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE 25%GF
CONE
Hastelloy®
Monel
SPINDLE
Monel
WASHER
Monel
AISI 303
AISI 316L
AlSiBz
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
160
KEY FEA
TURES
FEATURES
• Self adjusting, spring loaded V-ring gland packing
• Seft hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-ring and nickel gasket fitted into the gland guarantee a secondary sealong and exclude humidity
• Soft seat offers low operating torque and is captivated to avoid extrusion and blomage of the valve
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-6 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
1,1
6 mm
08-8
High pressure cylinder valves, 2-piece sturdy stem design
with self adjusting, spring loaded gland packing, for
corrosive technical gases, soft seat
D
CEODEUX
160
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
Metal seat
•
•
•
•
•
threading for flow restrictor
dip tube connection
alternative seat disc materials: Nylon®, PCTFE and PVDF ( KYNAR® )
valve spindle with shear off section to prevent overtorquing
key operation
OPTIONS
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• serial number or range
• type of gas
• connections
• safety device specifications
SERIES
D160 1
D160 2
Body material
AlSI 303
St52-3
Body material
AlSI 316L
9SMn28
D160 4
AlSiBz
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE
SEA
T DISC
SEAT
PCTFE
PIN
AISI 316L
SPINDLE
AISI 316L
Monel
WASHER
AISI 303
AISI 316L
AlSiBz
AISI 303
AISI 316L
St52-3
9SMn28
AlSiBz
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
161
KEY FEA
TURES
FEATURES
• O-ring and nickel gasket fitted into the gland guarantee a secondary sealong and exclude humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-6 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
1,1
6 mm
08-8
High pressure cylinder valves, 2-piece sturdy stem design
with self adjusting, spring loaded gland packing, for
corrosive technical gases, metal-metal seat
D
CEODEUX
161
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Dip tube connection
Valve spindle with shear off section to prevent overtorquing
Key operation
•
•
•
•
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D161 1
D161 2
D161 4
Body material
Body material
Body material
AlSI 303
AlSI 316L
St52-3
9SMn28
AlSiBz
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE
SPINDLE
AISI 316L
Monel
WASHER
AISI 303
AISI 316L
AlSiBz
AISI 303
AISI 316L
St52-3
9SMn28
AlSiBz
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
165
KEY FEA
TURES
FEATURES
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-5 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
1,1
6 mm
08-8
High pressure cylinder valves, packed 2-piece sturdy stem
design, for corrosive technical gases
D
CEODEUX
165
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
Ø 65 mm
128 mm
OPTIONS
• Threading for flow restrictor
• Key operation
• Dip tube connection
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D165 1
D165 2
D165 3
D165 4
Body material
AlSI 303
St52-3
Brass
AlSiBz
Body material
AlSI 316L
9SMn28
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE
SPINDLE
AISI 303
AISI 303
gold-plated
WASHER
Monel
AISI 303
AISI 316L
Brass
AlSiBz
AISI 303
AISI 316L
St52-3
9SMn28
Brass
AlSIBz
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
175
KEY FEA
TURES
FEATURES
• Highly corrosion-resistant AlSiBz body and Monel stem
• Designed for yoke connector application
• Valve design complies with US Chlorine Institute specifications
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
Material
• body
• stem
• packing
• body
35 bar/500 psi
-25°C up to + 65°C
at pmax
10-4 mbarl/sec
10-4 mbarl/sec
10-8 mbarl/sec
0,75
5 mm
A1SIBr
monel ®
PTFE
see below
08-8
Low pressure cylinder valves, packed 1-piece sturdy stem
design, for chlorine
D
CEODEUX
175
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
Pressure relief devices are in accordance with
CGA S-1.1 for chlorine
125 mm
OPTIONS
• Type of gas
• Connections
Connections:
A outlet
C inlet
G dip tube
SERIES
D175 4
Body material
AlSiBz
Body material
Body material
www
rotarex.com
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
ORDERING
• Reseating set
• Various inlet and outlet connections and connection standards
CEODEUX
PURETEC
D
186
KEY FEA
TURES
FEATURES
• Spindle threads not in gas wetted area
• Gland nut locked with hexagon nut
• Self centering seat offers low closing torques
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-5 mbarl/sec
10-5 mbarl/sec
0,25
3 mm
08-8
High pressure lecture bottle valves, packed design,
for various gases
D
CEODEUX
186
PURETEC
OPTIONS
• Dip tube and/ or dip tube connection
ORDERING
• Type of gas
• Connections
SERIES
D186 1
D186 3
D186 4
Body material
AlSI 303
Brass
AlSiBz
Body material
AlSI 316L
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE
CONE
AISI 303
gold plated
SPINDLE
Monel
AISI 316L
WASHER
AISI 316
Monel
AISI 316L
AISI 303
AISI 316L
AISiBz
Brass
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
200
KEY FEA
TURES
FEATURES
• Soft seat sealing arrangement offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• High performance thrust pad
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
•internal
•external
•safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to+ 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,35
3,5 mm
see table on back side
08-8
High pressure cylinder valves, diaphragm seal type,
for high purity gases
D
CEODEUX
200
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
• Chrome or nickel plating, for brass valves
• Alternative seat disc materials: PCTFE, PI (Vespel®),
PA 6.6 (Nylon®)
• Gas wetted components electrochemically polished
• Clean room assembling
• Cleaning for UHP / ECD applications
• Dip tube connections
• Flow restrictor threading
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D200 1
D200 3
Body material
AlSI 303
Body material
AlSI 316L
D200 6
Brass
Nickel
Body material
OPTIONS
with / without safety device
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 303
AISI 316L
Brass
Nickel
SEA
T DISC
SEAT
PCTFE
PI (Vespel®)
PA 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
201
KEY FEA
TURES
FEATURES
• All metal seal, no contamination
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,25
3,5 mm
08-8
High pressure cylinder valves, diaphragm seal type with
metal to metal seat, for high purity gases
D
CEODEUX
201
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Chrome or nickel plating, for brass valves
Cleaning for UHP/ECD applications
Dip tube connections
Flow restrictor threading
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
SERIES
D201 1
D201 3
Body material
AlSI 303
Brass
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
LOWER SPINDLE
AISI 303
Nickel
AISI 303
AISI 316L
Brass
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
265
KEY FEA
TURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and cost of
ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,35
3,5 mm
08-8
High pressure cylinder valves, dual port, diaphragm seal
type, for high purity gases
D
CEODEUX
265
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
• Chrome or nickel plating
• Alternative seat disc materials: Pa 6,6 (Nylon®), PCTFE,
PI (Vespel®)
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D265 1
D265 3
D265 6
Body material
AISI 303
Brass
Nickel
Body material
AISI 316L
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
®
Nickel
LOWER SPINDLE
AISI 303
AISI 316L
Brass
Nickel
SEA
T DISC
SEAT
PCTFE
PI (Vespel®)
PA 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
266
KEY FEA
TURES
FEATURES
• Easy withdrawal of liquefied gas by pressuring through vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to+ 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,25
3,5 mm
08-8
High pressure cylinder valves, dual port, diaphragm seal
type, for various high purity gases
D
CEODEUX
266
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
• Alternative body materials
• Gas wetted components
electrochemically polished
• cleaning for UHP/ECD applications
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D266 1
D266 3
Body material
AISI 303
Brass
Body material
AISI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
®
Nickel
LOWER SPINDLE
AISI 303
Nickel
AISI 303
AISI 316L
BRASS
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
260
KEY FEA
TURES
FEATURES
cost of ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
45 bar/650 psi
-25°C up to + 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
1,0
8 mm
08-8
Low pressure, high flow cylinder valves, dual port, diaphragm
seal type, for high purity gases
D
CEODEUX
260
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
• Cleaning for UHP/ECD applications
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D266 1
D266 3
Body material
AISI 303
Brass
Body material
AISI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
®
Nickel
LOWER SPINDLE
AISI 303
Nickel
AISI 303
AISI 316L
BRASS
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
250
KEY FEA
TURES
FEATURES
• Easy operation under high pressure
• O-rings fitted into the gland to exclude penetration of humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
0,25
4 mm
08-8
High pressure lecture bottle valves, diaphragm seal type,
for various gases
D
CEODEUX
250
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Alternative body materials
Alternative seat disc materials: PA 6,6 (Nylon®), PCTFE, PI (Vespel®)
Dip tube connection
•
•
•
•
Connections:
A outlet
C inlet
G dip tube
F flow restrictor
ORDERING
• Type of gas
• Connections
• Aptions and special features
SERIES
D250 1
D250 3
D250 4
Body material
AlSI 303
Brass
AlSiBz
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
®
LOWER SPINDLE
AISI 303
AISI 316L
Brass
SEA
T DISC
SEAT
Al SI Br
PCTFE
PI (Vespel®)
Pa 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Al Si Br
Al Si Br
Al Si Br
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
251
KEY FEA
TURES
FEATURES
• Easy operation under high pressure
• O-rings fitted into the gland to exclude penetration of humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
0,2
2,5 mm
08-8
High pressure lecture bottle valves, diaphragm seal type with
metal to metal seat, for various gases
D
CEODEUX
251
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Connections:
A outlet
C inlet
G dip tube
F flow restrictor
ORDERING
• Type of gas
• Connections
SERIES
D251 1
D251 3
D251 4
Body material
AlSI 303
Brass
AlSiBz
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
®
LOWER SPINDLE
AISI 303
Nickel
AISI 303
AISI 316L
BRASS
Al SI Br
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
300
KEY FEA
TURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
Material
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High pressure cylinder valves, tied diaphragm seal type,
for ultra high purity gases
D
CEODEUX
300
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
and seat disc materials: PVDF, PI (Vespel®), PCTFE
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D300 1
D300 6
Body material
AlSI 316L
Nickel
Body material
Hastelloy®
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
330
KEY FEA
TURES
FEATURES
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
spindle and the operating handwheel
• O-Rings in the gland and on spindle guarantee a secondary sealing
• threaded vent hole
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,35
4 mm
08-8
High flow tube trailer or ton container valves, tied diaphragm
seal type, for ultra high purity corrosive gases
D
CEODEUX
330
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
• Alternative body materials and seat disc
materials: PVDF, PCTFE, PI (Vespel ®)
• Clean room assembing
• cleaning for UHP / ECD applications
Connections:
A outlet
C inlet
F flow restrictor
G dip tubea
ORDERING
• Body material
• Type of gas
• Connections
SERIES
D330 1
D330 6
Body material
AlSI 316L
Hastelloy®
Body material
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Hastelloy®
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
340
KEY FEA
TURES
FEATURES
cost of ownership
• Threaded vent hole
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-8 mbarl/sec
10-8mbarl/sec
10-8 mbarl/sec
0,35
4 mm
08-8
High flow cylinder valves, dual port, tied diaphragm seal
type, for ultra high purity corrosive gases
D
CEODEUX
340
PURETEC
DESIGN V
ARIANT Pressure relief devices are in accordance with CGA S-1.1
VARIANT
SAFETY DEVICE
OPTIONS
ORDERING
• Type of gas
• Connections
SERIES
D340 1
D 340 6
Body material
AlSI 316L
Hastelloy®
Body material
Nickel
Body material
Monel
Connections:
A, A1 outlets
C inlet
G dip tube
• Alternative body materials: Nickel, Hastelloy®
and seat disc materials: PVDF, PI (Vespel ®), PCTFE
• Various inlet and outlet connections and connection
standards, including CGA 630/710
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
341
KEY FEA
TURES
FEATURES
cost of ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to + 65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,3
4 mm
08-8
High flow cylinder valves, dual port, tied diaphragm seal
type, with metal to metal seat, for ultra high purity reactive
gases
D
CEODEUX
341
PURETEC
DESIGN V
VARIANT
SAFETY DEVICE
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D341 1
D 341 6
Body material
AlSI 316L
Hastelloy®
Body material
Nickel
Body material
Monel
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T
SEAT
Nickel
Monel
AISI 316L
Hastelloy®
Nickel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
342
KEY FEA
TURES
FEATURES
cost of ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
45 bar/ 650 psi
-25°C up to +65 °C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,7
8 mm
08-8
Low pressure, high flow cylinder valves, dual port, tied
diaphragm seal type, for ultra high purity corrosive gases
D
CEODEUX
342
PURETEC
DESIGN V
VARIANT
SAFETY DEVICE
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D342 1
D 342 6
Body material
AlSI 316L
Hastelloy®
Body material
Nickel
Body material
Monel®
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
395
KEY FEA
TURES
FEATURES
cost of ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High pressure cylinder valves, dual port, tied diaphragm seal
type, for ultra high purity gases
D
CEODEUX
395
PURETEC
DESIGN V
VARIANT
Ø 65 mm
SAFETY DEVICE
135 mm
Connections:
A, A1 outlets
C inlet
G dip tube
ORDERING
• Type of gas
• Connections
SERIES
D395 1
D395 6
Body material
AlSI 316L
Hastelloy®
Body material
Nickel
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
390
KEY FEA
TURES
FEATURES
• Burst disc materials are nickel or AISI 316L
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High pressure tube trailer or ton container valves, tied
diaphragm seal type, for ultra high purity reactive gases
D
CEODEUX
390
PURETEC
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
• Alternative body materials and seat disc materials:
PVDF, PI Vespel ®
ORDERING
• Body material
• Type of gas
• Connections
SERIES
D390 1
Body material
D390 6
AlSI 316L
Hastelloy®
Body material
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
LOWER SPINDLE
Hastelloy®
AISI 316L
Nickel
Hastelloy®
PCTFE
SEA
T DISC
SEAT
PVDF
PI (Vespel®)
PIN
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Hastelloy®
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
350
KEY FEA
TURES
FEATURES
• very low internal volume with minimum dead spaces. This is particularly beneficial, when using
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important
safety feature especially during transportation
• In the closed position the valve fits under all standard valve protection caps
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Pneum. act. press.
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
165 bar/2400 psi
min 5, max 10 bar
-25°C up to +65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High pressure, air operated cylinder valves, tied diaphragm
seal type, for ultra high purity gases
D
CEODEUX
350
PURETEC
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
•
•
•
•
•
•
•
Alternative body materials and seat disc materials: PVDF, PCTFE, PI (Vespel®)
Cleaning for UHP / ECD applications
Dip tube connection
Proximity switch
Proximity switch
ORDERING
• Body material
• Type of gas
• Connections
SERIES
D350 1
D350 6
Body material
AlSI 316L
Nickel
Body material
Hastelloy®
Body material
OPTIONS
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
Stainless steel , brass nickel plated, or aluminum, cylinder
valve
APPLICA
TIONS
APPLICATIONS
D
Constant flow
cylinder valve
405
KEY FEA
TURES
FEATURES
• O-Ring seal provides durability for multiple use calibration applications
• Compact, light weight design ideal for portability
• Cylinder valve, pressure regulator and fill adapter - entire delivery system available from one supplier.
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Working pressure max.
Helium leak rate
Temperature range
max pressure for Aluminum
Wetted materials
• Body
• Valve seat/seal
• O-ring
• Internal parts
600*/3000 psi
1 x 10-4 cc/sec
-5°F to 140°F
stainless steel, brass,
nickel plated brass,
aluminum
FPM
FPM
stainless steel
05-2
The series was designed for calibration applications. In
combination with pressure regulators of the Series SI 70, SL 70,
SA 70. They are excellent for field calibration, portable or
disposable cylinder use. The material compatibility with the
media make them suitable for special gas mixtures.
CEODEUX
PURETEC
D
405
DESIGN V
ARIANT
VARIANT
dimensional drawing in inches
BASIC MODELS
• Inlet connections: 3/4" - 16 UNF, 1" - 14 UNF
• Outlet connections: 5/8" - 18UNF
ORDERING
• Series number or range
• Connections
• Type of gas
OPTIONS
• Safety device acc. to CGA S1.1
• Choice of o-ring materials: EPDM
www
rotarex.com
CEODEUX-Ultra Pur
e Equipment T
echnology S.A.
Pure
Technology
IS
O 9001
ISO
CERTIFIED
Tel.: *352 32 78 32 - 299
Fax: *352 32 78 32 - 322
05-2
OUTLET CONNECTION
• For CGA 625 / 626 outlet connection
CEODEUX
PURETEC
D
750
KEY FEA
TURES
FEATURES
• Integrated electronic liquid level measuring device
• Whole system resistant to vibrations
• High leak tightness integrity trough diaphragm sealing
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,25
3,5 mm / 0.138"
08-8
High pressure cylinder valves, diaphragm seal type, with
integrated liquid level gauge
D
CEODEUX
750
PURETEC
DESIGN V
ARIANT
VARIANT
OPTIONS
ORDERING
•
•
•
•
•
•
• Type of gas
• Connections
SAFETY DEVICE
ACCESSORIES (SOLD SEP
ARA
TEL
Y)
SEPARA
ARATEL
TELY)
Display unit - Key features:
• Easily removable display unit
• Power supply: exchangeable LITHIUM-battery or external 5 V supply
• Level monitoring by pushing the button to guarantee a long battery life
• Continuous LCD monitoring of level when powered by an external power source
• RS232 interface connection
• Dry switch (10%)
• Temperature range: -20°C – 60°C
Calibration unit - Key features:
• Calibration of the level measurement during the first filling of the cylinder
• Possibility of re-calibration
SERIES
D750 1
D750 3
Body material
AlSI 303
Brass
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM LOWER SPINDLE
Hastelloy
®
AISI 303
Nickel
ELECTRODES
Brass
AISI 303
AISI 316L
SEALS
PCTFE
AISI 303
AISI 316L
Brass
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
751
KEY FEA
TURES
FEATURES
• Integrated electronic liquid level measuring device
• Whole system resistant to vibrations
• High leak tightness integrity trough diaphragm sealing
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C /
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-8 mbarl/sec
0,35
3,5 mm / 0.138"
08-8
High pressure cylinder valves, diaphragm seal type, with
integrated liquid level gauge
D
CEODEUX
751
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Alternative seat disc materials: PCTFE, PI (Vespel ®), PA 6.6 (Nylon®)
•
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
ACCESSORIES (SOLD SEP
ARA
TEL
Y)
SEPARA
ARATEL
TELY)
Display unit - Key features:
• Easily removable display unit
• Power supply: exchangeable LITHIUM-battery or external 5 V supply
• Level monitoring by pushing the button to guarantee a long battery life
• Continuous LCD monitoring of level when powered by an external power source
• RS232 interface connection
• Dry switch (10%)
• Temperature range: -20°C – 60°C
Calibration unit - Key features:
• Calibration of the level measurement during the first filling of the cylinder
• Possibility of re-calibration
SERIES
D751 1
D751 3
Body material
AlSI 303
Brass
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
LOWER SPINDLE
AISI 303
AISI 316L
Brass
SEA
T DISK ELECTRODES
SEAT
Nickel
PCTFE
AISI 303
AISI 316L
SEALS
Brass
PCTFE
AISI 303
AISI 316L
Brass
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
335
KEY FEA
TURES
FEATURES
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000psi
-40oC up to +70oC
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,35
4 mm
08-8
High flow cylinder valves, tied diaphragm seal type, for ultra
high purity corrosive gases
D
CEODEUX
335
PURETEC
Connection
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
OPTIONS
ORDERING
and seat disc materials: PVDF, PCTFE,
PI (Vespel ®)
• Body material
• Type of gas
• Connections
SERIES
D335 1
D335 6
Body material
AlSI 316L
Nickel
Body material
Hastelloy®
Body material
Monel®
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
SAFETY DEVICE
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
336
KEY FEA
TURES
FEATURES
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000psi
-40oC up to +70oC
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,3
4 mm
08-8
High flow cylinder valves, tied diaphragm seal type with
metal to metal seat, for ultra high purity reactive gases
D
CEODEUX
336
PURETEC
Connection
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
OPTIONS
ORDERING
• Alternativ body materials
• Body material
• Type of gas
• Connections
SERIES
D336 1
D336 6
Body material
AlSI 316L
Nickel
Body material
Hastelloy®
Body material
Monel®
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T
SEAT
Nickel
Monel
AISI 316L
SAFETY DEVICE
Hastelloy®
Nickel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
337
KEY FEA
TURES
FEATURES
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
45 bar/650 psi
-40oC up to +70oC
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,7
8 mm
08-8
Low pressure, high flow cylinder valves, tied diaphragm seal
D
CEODEUX
337
PURETEC
Connection
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
OPTIONS
ORDERING
and seat disc materials: PVDF, PCTFE,
PI (Vespel ®)
• Body material
• Type of gas
• Connections
SERIES
D337 1
D337 6
Body material
AlSI 316L
Nickel
Body material
Hastelloy®
Body material
Monel®
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel®)
AISI 316L
Nickel
AISI 316L
SAFETY DEVICE
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
195
KEY FEA
TURES
FEATURES
• Eliminates need for 2-valve system on certain containers reducing leak risk potential and cost of
ownership
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-6 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
1
6 mm
08-8
High pressure cylinder valves, dual port, 2-piece sturdy stem
design with self adjusting, spring loaded gland packing,
for corrosive technical gases, soft seat
D
CEODEUX
195
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Connections:
A, A1 outlets
C inlet
F, F1 flow restrictor
G dip tube
Dip tube connection
Alternative body material: carbon steel
Alternative seat disc materials: Nylon®, PCTFE and PVDF ( KYNAR® )
Key operation
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
SERIES
D195 1
D195 2
Body material
AlSI 303
11SMn30
Body material
AlSI 316L
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
PTFE
SEA
T DISC
SEAT
PCTFE
PIN
AISI 316L
SPINDLE
AISI 316L
WASHER
AISI 303
AISI 316L
AISI 303
AISI 316L
11SMn30
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
131
KEY FEA
TURES
FEATURES
• Freedom from seizure when used with corrosive gases - gas does not come into contact with the
valve operating mechanism
• Positive and effective operation - valve spindle is mechanically linked to the pneumatic actuator
• Long life - valve spindle and seat are replaceable
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle, when
opening the valve, rectification is readily achieved by tightening the gland packing nut
• Low internal volume - this is particularly beneficial, when using the valve for hygroscopic corrosive or
high purity gases, where inert gas purging may be necessary before opening or after closing the valve
• In the closed position, the valve fits under most standard valve protection caps
• The air actuator is fitted with a quick connector. It is locked in place by the manual override
• The valve is held closed by the spring, in addition for safety reasons, it can be locked in the closed
position by the manual override
• By applying air pressure to the piston, the valve opens
• Retightening of the packing can be done with the air actuator in place
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Pneum. act. press.
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
5 bar min.
-25°C up to +65°C
at pmax
10-5 mbarl/sec
10-5 mbarl/sec
10-8 mbarl/sec
0,25
2,8 mm
08-8
High pressure, air operated cylinder valves, packed needle
stem design, for corrosive high purity gases
D
CEODEUX
131
PURETEC
DESIGN V
ARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Dip tube connection
Proximity switch
Soft seat
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
Connections:
A: outlet
C: inlet
F: flow restrictor
G: dip tube
SERIES
D131 1
D131 3
D131 4
Body material
AlSI 303
Brass
AlSI Bz
Body material
AlSI 316L
Body material
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
SEA
T SEAL
SEAT
SPINDLE
PTFE 25%GF
PTFE Carbon filled
AISI 303
AISI 316L
gold plated gold plated
SEA
TG A S
SEAT
AISI 316L
DISTRIBUTION
AISI 303
RING
AISI 316L
AISI 303
AISI 316L
Brass
AlSiBz
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
158
KEY FEA
TURES
FEATURES
• high Cv 2,8 , 12mm orifice
• Removable seat
• O-ring gasket fitted into the packing support and the gland guarantee a secondary sealing and
exclude humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-5 mbarl/s
10-5 mbarl/s
2.8
12 mm
08-8
High pressure bulk valves, high flow, 2-piece sturdy stem
for corrosive technical gases, soft seat
D
CEODEUX
158
PURETEC
DESIGN V
ARIANT
VARIANT
77
OPTIONS
Dip tube connection
Alternative seat disc materials: PCTFE and PVDF ( KYNAR® )
RPV
81
ORDERING
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
• Type of gas
• Connections
SERIES
D158 1
Body material
AlSI 316Ti
163
•
•
•
•
GAS WETTED MA
TERIALS
MATERIALS
BODY
P A C K I N G SEA
T DISC
SEAT
SCREW
SPINDLE
WASHER
GASKET
SEA
T
SEAT
PTFE
AISI 316Ti
AISI 316Ti
AISI 316L
Ni
Hastelloy
PCTFE
AISI 316Ti
AISI 316 Ti
O-RING
FPM
EPDM
FFKM
PCTFE
SOCKET
316 Ti
SPINDLE
WIPE RING
FEP
PTFE
www
rotarex.com
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
159
KEY FEA
TURES
FEATURES
• high Cv 3 , 12mm orifice
• Removable seat
• O-ring gasket fitted into the packing support and the gland guarantee a secondary sealing and
exclude humidity
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25°C up to +65°C
at pmax
10-5 mbarl/s
10-5 mbarl/s
3
12 mm
08-8
High pressure bulk valves, high flow, 2-piece sturdy stem
for corrosive technical gases, removable soft seat
D
CEODEUX
159
PURETEC
55
DESIGN V
ARIANT
VARIANT
140
A
OPTIONS
72
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
• Alternative seat disc materials: PCTFE and PVDF ( KYNAR® )
• Valve spindle with shear off section to prevent overtorquing
RPV
G
ORDERING
C
• Type of gas
• Connections
SERIES
D159 1
Body material
AlSI 316Ti
AISI 303
GAS WETTED MA
TERIALS
MATERIALS
BODY
PACKING
SEA
T DISC
SEAT
SCREW
SPINDLE
WASHER
GASKET
REMOV
ABLE SEA
T
REMOVABLE
SEAT
PTFE
PCTFE
AISI 316Ti
AISI 316Ti
AISI 316L
Ni
Hastelloy
AISI 316Ti
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
183
KEY FEA
TURES
FEATURES
• Double reversed seat design offers high level of security
• Primary soft seat to guarantee low sealing forces and an high leak integrity
• Second seat to ensure tightness if top valve destroyed
• 2-piece sturdy stem design
• Non-rotating, thread less lower spindle
• Self-adjusting, spring-loaded V-ring gland packing
• O-ring fitted into gland nut guarantees a secondary sealing and exclude humidity
• Tamper proof by a special nut
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Working pressure:
T° range:
Helium leak rate
•Internal
•External
•Piston
Flow coefficient Cv
Seat orifice
Gas wetted material:
200bar/3000psi
-25°C up to +65°c
10-5 mbar l /sec
10-5 mbar l/sec
10-3 mbar l/sec
1,15
12 mm
see table
08-8
High Pressure Super Tube Trailor drums &
cylinders Valve with double independant
sealing mechanism, reversed seat design,
for corrosive applications
D
CEODEUX
183
PURETEC
DESIGN V
ARIANT
VARIANT
146
• Inlet protection connection device
• Flange
• Forged body
OPTIONS
• Threading for floor restrictor
• Alternative seat material: PCTFE / PVDF
• Valve spindle with share off section to prevent over torque
• Open/Close indicator
ORDERING
• type of gas
• connections
88
B
sssssssss
G
SERIES
D183
Body material
AlSI 316 Ti
C
GAS WETTED MA
TERIALS:
MATERIALS:
AISI 316 Ti
BODY
AISI 316 Ti
PACKING
PTFE
PACKING
WASHER
AISI 316 L
SPRING
SPRING
WASHER
1.4310
AISI 316 L
SEAT
DISC
SPINDLE
WAS HERS
PACKING
SOCKET
PCTFE
PVDF
Monel 500K
AISI 316 Ti
PTFE
AISI 316 Ti
PISTON
TUBE
SPINDLE WIPE
RING
AISI 316 L
AISI 316 L
FEP
PTFE
www
rotarex.com
ROTAREX
Group
PFA
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
252
KEY FEATURES
• Soft seat sealing offers low operating torque
• O-ring fitted into the gland to exclude penetration of humidity
STANDARD SPECIFICATION
Temperature range
Helium leak rate at p max
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25 °C up to +65 °C
10-7 mbarl/sec
10-7 mbarl/sec
10-7 mbarl/sec
0,25
4 mm
08-8
High pressure, lecture bottle valves, diaphragm seal type,
for various purity gases, with top outlet
D
CEODEUX
252
PURETEC
DESIGN VARIANT
Drawing=D 195
Pressure relief devices are in accordance with CGA S-1.1,
EN ISO 4126 or other national standards
Safety device
OPTIONS
• Chrome or nickel plating for brass valves
• Alternative body materials and seat disc materials: PCTFE, PI, PA6.6
ORDERING
When ordering, please specify :
• Body material
• Type of gas
• Connections
GAS WETTED MATERIALS
AISI303
AISI303
AISI316L
AISI316L
BRASS
BRASS
BRASS
ASB
ASB
ASB
DIAPHRAGM
Hastelloy
AISI303
LOWER SPINDLE
AISI316L BRASS
ASB
www
rotarex.com
ROTAREX
Group
PCTFE
SEAT DISC
PI
PA6.6
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
225
KEY FEA
TURES
FEATURES
• Soft seat sealing offers low operating torque
• High performance thrust with ball
• Open / close indicator
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar for Europa /5500 psi for USA
-25°C up to +65°C
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
10-7 mbarl/sec
????????????
3,5 mm
08-8
High pressure cylinder valves, diaphragm
seal type, for high purity gases
D
CEODEUX
225
PURETEC
DESIGN V
ARIANT
VARIANT
Drawing=D195
Safety device
Chrome or nickel plating for brass valves
Alternative body materials and seat disc materials: PCTFE, PI, PA6.6
Ceaning for UHP / ECD applications
•
•
•
•
•
•
•
)
• Body material
• Type of gas
• Connections
$
ORDERING
*
&
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Elgiloy
LOWER SPINDLE
AISI 303
AISI 316 L
BRASS
SEA
T DISC
SEAT
PCTFE
PI
PA6.6
AISI 303
AISI 303
AISI 316L
OPTIONS
AISI 316L
BRASS
BRASS
BRASS
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
240
KEY FEA
TURES
FEATURES
• Diaphragm direct seal type
• High performance thrust with ball
• Low internal volume with minimum dead spaces
• Pneumatically actuated version see SERIES D290
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-40 °C up to + 65 °C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,3
4 mm
08-8
High pressure, stainless steel cylinder valves, diaphragm direct
seal Type, for ultra high purity gases
D
CEODEUX
240
PURETEC
DESIGN V
ARIANT
VARIANT
or other national standards
Safety device
OPTIONS
$
Alternative seat disc materials: PCTFE, PI
)
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
*
&
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
(Elgiloy®*,
UNS 30003 Phynox®*….)
SEA
T DISC
SEAT
PCTFE
PI
AISI 316L
AISI 316L
AISI 316L
*Elgiloy® is a registered trademark of Elgiloy Specialty Metals
Phynox® is a registered trademark of Arcelor
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
290
KEY FEA
TURES
FEATURES
• Diaphragm direct seal type
• Low internal volume with minimum dead spaces
• Manually actuated version see SERIES D240
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar/3000 psi
-25 °C up to + 65 °C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,3
4 mm
08-8
High pressure, stainless steel cylinder valves, pneumatically
actuated diaphragm direct seal Type, for ultra high purity
gases
D
CEODEUX
290
PURETEC
DESIGN V
ARIANT
VARIANT
or other national standards
Safety device
OPTIONS
$
Alternative seat disc materials: PCTFE, PI
)
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
*
&
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
(Elgiloy®*,
UNS 30003 Phynox®*….)
SEA
T DISC
SEAT
PCTFE
PI
AISI 316L
AISI 316L
AISI 316L
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
283
KEY FEA
TURES
FEATURES
• Elimination of cylinder cleaning as contamination is kept out even if
valve is left open
• Cost reduction as cylinder purging is no longer requested
• Increased safety as no filling is allowed without special adaptor
• Increased safety as no backflow occurs when mixing or manifolding
Temperature range
Helium leak rate
• internal
• external
Flow coefficient Cv
Seat orifice size
Residual pressure
200 bar/3000 psi
-25°C up to +65°C / -4oF up to +158oF
at pmax
10-7 mbarl/sec
10-7 mbarl/sec
0,35
3,5 mm
1 to 5 bar
08-8
High pressure cylinder valves, diaphragm seal type, in brass,
for high purity gases with integrated residual pressure device
D
CEODEUX
283
PURETEC
DESIGN V
ARIANT
VARIANT
OPTIONS
• Alternative seat disc materials: PVDF, PI (Vespel®), PA6.6 (Nylon®), PCTFE
ORDERING
• Type of gas
• Connections
SERIES
D283 3
Body material
BRASS
Safety device
GAS WETTED MA
TERIALS
MATERIALS
DIAPHRAGM
LOWER SPINDLE
SEA
T DISC
SEAT
PCTFE PVDF
Brass
Hastelloy
Brass
Brass
Hastelloy
Brass
Brass
Hastelloy
Brass
Brass
Hastelloy
Brass
www
rotarex.com
ROTAREX
Group
PI (Vespel®)
PA 6.6 (Nylon®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
325
KEY FEATURES
• Robust and safe in worst conditions.
• Soft seat sealing combined with a mechanical stop to prevent the seat extrusion in case of
excessive torque.
• The mechanical stop acts as secondary sealing in case of seat burning.
• Freedom of internal threads and springs insures minimum particle generation.
• High leak tightness integrity through diaphragm sealing up to 200 bar. (2900 PSI)
• Very low internal volume with minimum dead space.
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and the operating hand-wheel.
• Valve can be operated using a flat key, if hand-wheel is broken.
• O-Rings in the gland and on spindle guarantee a secondary sealing against the atmosphere.
• Threaded vent hole. (e.g. to connect pipe away or sensor)
Working pressure p max
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 2900 psi
-40 °C to + 65 °C
10-8mbarl/sec
10-8mbarl/sec
10-8mbarl/sec
0.35
4 mm
08-8
High flow cylinder valves, tied diaphragm seal type, for
ultra high purity corrosive gases
D
CEODEUX
325
PURETEC
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN VARIANT
SAFETY DEVICE
OPTIONS
and seat disc materials: PVDF, PI (Vespel ®)
• electrochemically polished
ORDERING
• Body material
• Type of gas
• Connections
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
AISI 316L
OPTIONAL (please contact us before ordering)
Hastelloy®
Nickel
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
392
KEY FEA
TURES
FEATURES
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
and the operating mechanism
locked in the closed position by manual operation of the handwheel. This is an important safety
feature especially during transportation.
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
165 bar / 2400 psi
-25°C up to +65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High pressure, tube trailor or ton container valves, Tied diaphragm seal type, pneumatically actuated, for ultra high
purity reactive gases
D
CEODEUX
392
PURETEC
DESIGN V
ARIANT
VARIANT
Drawing=D390
Safety device
Ø 75mm (2.95")
OPTIONS
•
•
•
•
•
•
•
Alternative body materials and seat disc materials: PCTFE, PVDF, PI
Dip tube connection
Proximity switch
ORDERING
• Body material
• Type of gas
• Connections
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM LOWER SPINDLE
Hastelloy
AISI 316L
Hastelloy
SEAT DISC
PCTFE
PVDF
PIN
PI
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy
Hastelloy
Hastelloy
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
380
KEY FEA
TURES
FEATURES
and the operating mechanism
feature especially during transportation.
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40°C up to + 70°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,35
4 mm
08-8
High flow, tube trailor or ton container valves, Tied diaphragm seal type, pneumatically actuated, for ultra high
purity corrosive gases
D
CEODEUX
380
38380
PURETEC
DESIGN V
ARIANT
VARIANT
Drawing=D390
Safety device
OPTIONS
• Alternative body materials and seat disc materials: PCTFE,
PVDF, PI
ORDERING
• Body material
• Type of gas
• Connections
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
LOWER SPINDLE
AISI 316L
Hastelloy
SEAT DISC
PCTFE
PVDF
PIN
PI
AISI 316L
Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy
Hastelloy
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
339
KEY FEA
TURES
FEATURES
• Soft seat sealing combined with a metal sealing
• Very low internal volume with minimum dead space
and the operating handwheel
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
120 bar / 1740 psi
-40°C up to + 65°C
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
???????????????????????????????????????????
6 mm
08-8
High flow cylinder valves, tied diaphragm seal type,
for ultra high purity reactive gases
D
CEODEUX
339
PURETEC
DESIGN V
ARIANT
VARIANT
Drawing=D195
Safety device
Ø 65 (2.56")
OPTIONS
• Alternative body materials and seat disc materials: PCTFE, PI
ORDERING
• Body material
• Type of gas
• Connections
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
NICKEL
LOWER SPINDLE
NICKEL
SEAT DISC
PCTFE
PI
AISI 316L
AISI 316L
NICKEL
NICKEL
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
388
KEY FEA
TURES
FEATURES
• Knife edge seat to prevent creation of silicate layer on the valve seat.
and operating handwheel
feature especially during transportation
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40°C up to + 70°C / -40oF up to +70oF
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,25
4 mm
08-8
High flow cylinder valve, tied diaphragm seal type,
pneumatically actuated, for Silane or Diborane
D
CEODEUX
388
PURETEC
DESIGN V
ARIANT
VARIANT
Safety device
OPTIONS
Seat disSeat disc materials: PI (Vespel®)
Dip tube connection
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
SERIES
D388 1
Body material
AISI 316L
BODY
DIAPHRAGM
Hastelloy®
LOWER SPINDLE
AISI 316L
SEAT DISC
PI (Vespel® )
AISI 316L
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
344
KEY FEA
TURES
FEATURES
and operating handwheel
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
165 bar / 2400 psi
-40°C up to + 65°C / -40°F up to +149°F
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
Withdrawal valve :
Flow coefficient Cv
Seat orifice size
0,35
4 mm
Filling valve:
Flow coefficient Cv
Seat orifice size
0,24
3,5 mm
08-8
High flow dual port cylinder valve, tied diaphragm seal type,
for integrated system, for ultra high purity gases
D
CEODEUX
344
PURETEC
DESIGN V
ARIANT
VARIANT
Drawing=D320
Safety device
Drawings
•
•
•
•
•
•
OPTIONS
Alternative seat disc materials: PVDF, PI (Vespel®), PCTFE
Dip tube connection
ORDERING
• Type of gas
• Connections
SERIES
D 344 1
Body material
AISI 316L
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
LOWER SPINDLE
AISI 316L
SEA
T DISC
SEAT
PCTFE
PIN
PVDF PI (Vespel® ) AISI 616L
AISI 316L
AISI 316L
AISI 316L
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
394
KEY FEA
TURES
FEATURES
feature especially during transportation
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
165bar / 2400 psi
-40°C up to + 65° C / -40°F up to +149°F
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
Withdrawal valve:
Flow coefficient Cv
Seat orifice size
0,35
4 mm
Filling vale:
Flow coefficient Cv
Seat orifice size
0,24
3,5 mm
08-8
High flow dual port cylinder valve, tied diaphragm seal type,
pneumatically actuated, for integrated system, for ultra high
purity gases
D
CEODEUX
394
PURETEC
DESIGN VARIANT
Drawing=D320
Safety device
OPTIONS
Alternative seat disc materials: PVDF, PI (Vespel®), PCTFE
Dip tube connection
•
•
•
•
•
•
ORDERING
• Type of gas
• Connections
SERIES
D 344 1
Body material
AlSI 316L
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy
LOWER SPINDLE
AISI 316L
SEA
T DISC
SEAT
PCTFE
PVDF
PIN
PI (Vespel® )
AISI 316L
AISI 316L
AISI 316L
AISI 316L
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
386
KEY FEA
TURES
FEATURES
ST
ANDARD SPECIFICA
TION
STANDARD
SPECIFICATION
Temperature range
Helium leak rate
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
45 bar
-40oC up to +70oC
at pmax
10-8 mbarl/sec
10-8 mbarl/sec
10-8 mbarl/sec
0,3
3,8 mm
08-8
High flow cylinder valves, tied diaphragm seal type ,
pneumatically actuated with metal to metal seal
for ultra high purity oxydant gases
D
CEODEUX
386
PURETEC
Connection
A outlet
C inlet
F flow restrictor
G dip tube
DESIGN V
ARIANT
VARIANT
OPTIONS
ORDERING
• Alternativ body materials
• Body material
• Type of gas
• Connections
SERIES
D386 1
D386 6
Body material
AlSI 316L
Nickel
SAFETY DEVICE
Body material
Body material
Monel®
GAS WETTED MA
TERIALS
MATERIALS
BODY
DIAPHRAGM
Hastelloy®
Nickel
LOWER SPINDLE
AISI 316L
Hastelloy®
Nickel
SEA
T
SEAT
Nickel
AISI 316L
Nickel
Monel
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
202
KEY FEATURES
• Seat disc captivated to avoid extrusion
• Compact size
Standard specification
200 bar/3000 psi
Temperature range
-40°C (-40°F) up to 65°C (149°F)
Helium leak rate
at pmax
- internal
10-7 mbar.l/s
- external
10-7 mbar.l/s
- safety device
10-8 mbar.l/s
Flow coefficient Cv
0,35
Seat orifice size
3,5 mm
¼” NPT on ¾”-14 NGT inlet and
M10x0,75 on 25E inlet
None on all other inlets
08-8
High pressure cylinder valve, diaphragm
direct seal type, for high purity gases
D
CEODEUX
202
PURETEC
DESIGN VARIANT
65
SAFETY DEVICE
ORDERING
• type of gas
• connections
Connections:
A outlet
C inlet
F flow restrictor
G dip tube
G
C
SERIES
D202 3
Body material
Brass
A
48
F
• Chrome plating for brass valves
• Without or customized dip tube connections
99
OPTIONS
BODY
DIAPHRAGM
Stainless steel
VALVE SEAT
Brass
SEAT DISC
PA
Brass
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
304
APPLICA
TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Patented operating mechanism.
• Threaded weep hole for pipe away connection.
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40 °C (-40°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.35
4 mm
08-8
High flow cylinder valves, tied diaphragm double seal
D
CEODEUX
304
PURETEC
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
SAFETY DEVICE
• Alternative body materials (Hastelloy®)
REQUEST FOR QUOTATION
please specify using product definition sheet Fr03.5.05.002
•
•
•
•
•
•
•
•
Connections:
A outlet
C inlet
F flow restrictor (std: 5/16”-UNF)
G dip tube (std: M10 x 0.75 or 1/4”NPT)
gas service / Working pressure
valve material
Inlet & outlet connections ( A & C acc, to national standard)
Threading for flow restrictor (F)
Threading dip tube connection (G)
Surface treatment
Pressure relief device
Packaging and conditioning
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
AISI 316L
Hastelloy®
Nickel
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
354
APPLICA
TION
APPLICATION
KEY FEATURES
• Strong closing force with the use of a hydraulic amplifier
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
Actuator air pressure
200 bar / 3000 psi
-25 °C (-4°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.35
4 mm
5-7 bar (72-100PSI)
08-8
D
CEODEUX
354
PURETEC
DESIGN VARIANT
SAFETY DEVICE
•
•
•
•
•
Alternative body materials (Hastelloy®)
O-ring for -40°C(-40°F)
Inductive proximity switch => air connexion must be M5
•
•
•
•
•
•
•
•
•
Connections:
A outlet
C inlet
P Air pressure connexion (M5 or 1/8” NPT or G1/8)
valve material
P Air pressure connexion
Surface treatment
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
AISI 316L
Hastelloy®
Nickel
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
389
APPLICA
TION
APPLICATION
KEY FEATURES
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-25 °C (-4°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.55
6 mm
5-7 bar (72-100PSI)
08-8
D
CEODEUX
389
PURETEC
DESIGN VARIANT
SAFETY DEVICE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Connections:
A outlet
C inlet
P Air pressure connexion (M5 or 1/8” NPT or G1/8)
valve material
P Air pressure connexion
Surface treatment
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
Nickel
Hastelloy®
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
605
APPLICA
TION
APPLICATION
Isolation valve in gas filling stations or installation as main shut-off
valve on bundles or trailers
KEY FEATURES
• 2-piece sturdy stem design.
• Silver ring combined with a PA (or PCTFE) seat disc for lowest tightness torque.
• No gas in contact with the operating mechanism & O-ring fitted into gland nut to exclude
humidity
• Soft seat encapsulated into the spindle to avoid extrusion and good sealing performances.
• Lower spindle design allows a smooth opening of the valve, and prevents adiabatic
compression.
Temperature range
• internal
• external
Flow coefficient Cv
Seat orifice size
300 bar / 4350 psi
-25 °C (-4°F) to + 65 °C (149°F)
10-3 mbar.l/s
10-3 mbar.l/s
1.5
10 mm
08-8
High pressure line valve in stainless steel for inert & various
gases.
D
CEODEUX
605
PURETEC
OPTIONS
• Seat disc & O-ring materials according gas applications
BODY
O-RING
AISI 316L
LOWER SPINDLE
STANDARD VALVE
AISI 316L
EPDM
SEAT DISC
PA
FPM
PCTFE
•
•
•
•
valve material
Connections:
A outlet
C inlet
ROTAREX
Group
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
www
rotarex.com
CEODEUX
PURETEC
D
604
APPLICA
TION
APPLICATION
KEY FEATURES
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40 °C (-40°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.3
4 mm
08-8
High flow line valves, tied diaphragm double seal type, for
D
CEODEUX
604
PURETEC
WKUHDGV0
RQ
9,(:;
DESIGN VARIANT
Ø65 (2.56")
§ 84
A
C
valve material
Surface treatment
§ 11,2
•
•
•
•
•
§ 36
§ 78
Connections:
A outlet
C inlet
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
AISI 316L
Hastelloy®
Nickel
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
639
APPLICA
TION
APPLICATION
KEY FEATURES
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40 °C (-40°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.5
6 mm
08-8
High flow line valves, tied diaphragm double seal type, for
D
CEODEUX
639
PURETEC
WKUHDGV0
RQ
9,(:;
DESIGN VARIANT
Ø65 (2.56")
§ 84
A
C
valve material
Surface treatment
§ 11,2
•
•
•
•
•
§ 36
§ 78
Connections:
A outlet
C inlet
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
Nickel
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
654
APPLICA
TION
APPLICATION
KEY FEATURES
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40 °C (-40°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.3
4 mm
5-7 bar (72-100PSI)
08-8
High flow line valves, tied diaphragm seal type, for ultra
D
CEODEUX
654
PURETEC
25,4 (1")
DESIGN VARIANT
4 threads M5
§
67
P
§ 124
§ 11,2
§ 36
§ 78
•
•
•
•
•
•
A
C
•
•
•
•
•
Connections:
A outlet
C inlet
P Air pressure connection (M5 or 1/8” NPT or G1/8)
valve material
P Air pressure connection
Surface treatment
OPTIONS
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
AISI 316L
Hastelloy®
Nickel
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY
CEODEUX
PURETEC
D
689
APPLICA
TION
APPLICATION
KEY FEATURES
Temperature range
• internal
• external
• safety
Flow coefficient Cv
Seat orifice size
200 bar / 3000 psi
-40 °C (-40°F) to + 65 °C (149°F)
10-8 mbar.l/s
10-8 mbar.l/s
10-8 mbar.l/s
0.5
6 mm
5-7 bar (72-100PSI)
08-8
High flow line valves, tied diaphragm seal type, for ultra
D
CEODEUX
689
PURETEC
25,4 (1")
DESIGN VARIANT
4 threads M5
§
67
P
OPTIONS
A
§ 11,2
§ 36
§ 78
•
•
•
•
•
•
Connections:
A outlet
C inlet
P Air pressure connection (M5 or 1/8” NPT or G1/8)
valve material
P Air pressure connection
Surface treatment
§ 124
C
•
•
•
•
•
DIAPHRAGM
AISI 316L
Hastelloy®
LOWER SPINDLE
STANDARD VALVE
Nickel
Hastelloy®
www
rotarex.com
ROTAREX
Group
SEAT DISC
PCTFE
PVDF
PI (Vespel®)
IS
O 9001
ISO
CERTIFIED
Tel.: +352 32 78 32 - 299
Fax: +352 32 78 32 - 322
08-8
BODY

CEODEUX

Transcription

Similar documents

BOAT SEAT - VA

Maimi Dade Portable Roll Formers

February 8th at 12:45 pm CINEPLANET 16

flu designs pleated seat cover fox racing proframe chest protector ea

Team Coaches Mainz05

Website page_GearUp Accessories Catalogue all Product

Hedstrom 2 in 1 Swing

Early Years newsletter

Inauguration of the Seat Belt Convincer at CEC

Feel it! Festival experience of seat belt convincer