capiz flush mount pendant Assembly Instructions from cb2

Transcription

capiz flush mount pendant Assembly Instructions from cb2
capiz
FLUSH MOUNT PENDANT
This page lists the contents included in the box.
Please take time to identify the hardware as well
as the individual components of the product. As
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect
them from damage. Please follow the assembly
instructions closely. Improper assembly can result
in personal or property damage.
IMPORTANT SAFETY INSTRUCTIONS:
If you are unsure about your ceiling type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
We recommend installation of this lamp be performed
by a licensed electrician.
Capiz is fragile, take extreme care during installation.
We recommend 2-3 adults to safely install this fixture.
!
hardware & components
?
tools required
800.606.6387
hex wrench
(included)
1 - support armature
1 - lamp assembly
4 - screws
3 - wire nuts
1 - socket assembly
4 - washers
Made in The Philippines - r03
4 - plastic anchors
4 - canopy bolts
1 - hex nut
3 - 13 watt max CFL bulbs
(NOT INCLUDED)
OR 3 - 60 watt max type A
standard bulbs (NOT
INCLUDED)
800.606.6252 | cb2.com
power drill
electrical tape
phillips head screwdriver
cleaning & care
Dust surfaces with a dry soft cloth.
Do not use cleaners or polishes
on the lamp.
1/4
capiz
FLUSH MOUNT PENDANT
1
2
A
B
Shut off the main electrical supply from the main fuse
box/circuit breaker. Carefully unpack all fixture parts and
hardware. Lay items out on a clear workspace.
Center support armature over center of ceiling junction
box and mark 4 holes on ceiling as shown.
A. Drill 4 holes slightly smaller in diameter than the plastic
anchors.
B. Insert 1 plastic anchor into each hole and gently tap
until it is flush with the ceiling.
3
Position holes in support armature over
plastic anchors. Insert 4 screws through
armature and into plastic anchors, and
secure (but do not over tighten) with a
phillips head screwdriver.
Made in The Philippines - r03
800.606.6252 | cb2.com
2/4
capiz
FLUSH MOUNT PENDANT
4
Fit threaded stem of socket assembly into
center washer of lamp fixture as shown. Attach
with 1 hex nut, and secure with the included
hex wrench.
5
A. Insert 3- bulbs (not included) into the sockets.
DO NOT EXCEED SPECIFIED WATTAGE.
B. With assistance of 1 to 2 people holding fixture,
lift pendant into position.
Carefully inspect the fixture wires:
• Neutral fixture wire = white
• Hot fixture wire = black
• Ground wire = green
- Attach the ground wire of the lamp to the ground
wire from the junction box. Fasten each together
with a wire nut and wrap the connection with
electrical tape.
- Attach the neutral fixture wire from the lamp to the
neutral junction box wire (usually white). Fasten
each together with a wire nut and wrap the
connection with electrical tape.
- Attach the hot fixture wire from the lamp to the hot
junction box wire (usually black). Fasten each
together with a wire nut and wrap the connection
with electrical tape.
Made in The Philippines - r03
800.606.6252 | cb2.com
B
A
3/4
capiz
FLUSH MOUNT PENDANT
6
Neatly tuck wires into the junction
box. With assistance, fit lamp fixture
into position, aligning holes of fixture
with corresponding holes in the
support armature. Secure with 4
canopy bolts and 4 washers.
Restore power to junction box and
test fixture.
Installation is now complete.
Made in The Philippines - r03
800.606.6252 | cb2.com
4/4