Engine Driven Units

Transcription

Engine Driven Units
Engine Driven Units
FP1000
Hale Products Engine Driven Units combine a range of diesel engines with our time proven
and reliable pumps to exceed your flow, pressure and lift needs.
For over a century, Hale Products has been the leader in providing engineered solutions and the
technical expertise for Industrial, Municipal and Nuclear emergency water supply applications.
DESCRIPTION*: The Hale FP1000 is a skid base mounted
diesel engine driven pump. Utilizing the Hale RSD series
pump the FP1000 meets NFPA 1901 pump performance by
providing 1,000 gpm (3,785 l/m) @ 150 psi (10.3 bar) from a
10’ foot (3.3 m) lift.
PUMP: The RSD series is a centrifugal pump with fine grain
alloy cast iron, with a minimum tensile strength of 30,000 PSI
(2,069 bar), volute and heads. The pump is vertically split on
a single plane for easy access of the bronze impeller and
clearance rings. Each vane of the impeller is hand-ground
and polished for maximum efficiency while utilizing minimal
horsepower. The pump will include intake and thermal relief
valves.
MANIFOLDS: The intake and discharge manifolds and valve
assemblies will be stainless steel for increased strength. The
intake will have (1) 6” NH threads. The discharge manifold
will be (4) direct actuated valves (remote manual or electric
actuation optional) with (4) 2.5” adaptor connections.
FUEL TANK/BASE: The engine, pump and manifolds will be
attached to a steel base. The base will include an integral 150
gallon (567 l) fuel tank with level indicator and side fork lift
pockets for ease of movement of the skid base mount only.
CONTROL PANEL: The control panel will be a pedestal
enclosure located to the curb side of the unit. The control
panel will include LED lighting, non-keyed ignition and
emergency shut-down control. The engine and pump controls
will include:
•
•
•
•
•
•
•
Engine RPM
Coolant Temperature
Oil pressure
Volt Meter
Hour Meter
Master Inlet Pressure
Master Discharge Pressure
ENGINE: The engine will be a 6 cylinder 4 cycle diesel John
Deere (other engine brands are optional) engine providing
200hp @ 2400 rpm. The engine will have electronic controls
with 12 volt electronics with 75A alternator. The engine will
have a fan forced cooled heavy duty radiator.
Total Pressure
Governor Plus
(TPG+)
OPTIONAL: The following options are available:
•
•
•
•
•
•
Open exterior frame with lifting points
Extreme weather engine and pump enclosure
Bronze body pump
Trailer with bumper or goose neck pull
Battery system and battery maintainer
Adjustable or fixed scene lighting
*Specifications and Drawings are subject to change without notice.
RSD-M Series
Centrifugal Pump
The Ultimate Flow Specialist ™
Unit Drawing and Pump Curve are
reference only.
Dimensions, Features and Performance
information is subject to change without
notice.
Various brands of engine are available
upon request.
The model prefix of “FP” designates
Fire Pump and meets NFPA 1901 for flow
performance. Other pump designations
are available upon request.
For any questions please visit www.haleproducts.com or contact your Hale Products, Inc. Sales Representative.
Hale Products, Inc.
607 NW 27th Ave, Ocala, FL 34475
Tel: 800.533.3569 Fax: 800.520.3473

Similar documents

Engine Driven Units

Engine Driven Units ENGINE: The engine will be a 6 cylinder 4 cycle diesel John Deere (other engine brands are optional) engine providing 275hp @ 2400 rpm. The engine will have electronic controls with 12 volt electro...

More information

Heavy duty PTO pump

Heavy duty PTO pump is self-adjusting and self-lubricating Heavy-duty precision ground, deep groove bearings are used for maximum life Three gear ratios available to maximize performance for most engine PTO combinat...

More information