AII 13317 - Moonroof Visor.fm

www.collegehillshonda.com
INSTALLATION
INSTRUCTIONS
PARTS LIST
Accessory
Application
MOONROOF VISOR
P/N 08R01-SZA-101
2015 PILOT
Publications No.
AII 51570
Issue Date
MAY 2014
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
10 mm Combination wrench
Moonroof visor
Scale
Isopropyl alcohol
Shop towels
Masking tape
Small phillips screwdriver
Torque screwdriver: T/N CDI401SM
2
Brackets A
Illustration of the Moonroof Visor on the Vehicle
MOONROOF
VISOR
2
Brackets B
4
Screws
4
Nuts
INSTALLATION
4
Protective tape
Sealer
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
• Install this accessory with care to avoid damaging
the vehicle.
• Install the moonroof visor using the specified bolts
and screws supplied. Never use a metal screw or nut
to secure the moonroof visor.
• Wash and wax the area to be covered with a
high-quality paste wax.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
AII 51570 (1405)
08R01-SZA1010-91
1 of 5
www.collegehillshonda.com
Installing the Moonroof Visor
3.
1.
Open the moonroof to the tilt up position.
2.
Using the measurements shown, check the seal on
the left and right side for a hole. If the seal has a hole
on either side, continue with step 3. Otherwise, go to
step 5.
Using a small phillips screwdriver, insert the sealer
into the hole towards the rear of the moonroof as
shown.
MOONROOF
FRONT
MOONROOF
FRONT
Make sure to
thoroughly
insert the sealer
into the hole.
HOLE
MOONROOF
FRONT
FRONT
WINDSHIELD
SEAL
FRONT
Open.
HOLE
MOONROOF
SMALL PHILLIPS
SCREWDRIVER
SEAL
MOONROOF
SECTION VIEW
410 mm
SEALER
4.
Insert the rest of the sealer towards the front of the
moonroof as shown. Make sure to thoroughly insert
the sealer into the hole.
5.
Open the moonroof to the fully open position.
40 mm
FRONT
SHOP TOWEL
Insert.
FRONT
WINDSHIELD
SEAL
Check this area
on the moonroof
glass seal.
AIR DEFLECTOR
ROOF PANEL
6.
2 of 5
AII 51570 (1405)
Roll up two shop towels and insert them between the
roof panel and air deflector to lower the air deflector.
Do not damage the air deflector.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
7.
Using isopropyl alcohol on a shop towel, thoroughly
clean the roof panel where the protective tape will
attach.
Clean with
isopropyl alcohol.
FRONT
9.
Using isopropyl alcohol on a shop towel, thoroughly
clean the roof panel where the protective tape will
attach.
PROTECTIVE
TAPE
ROOF
PANEL
PROTECTIVE
TAPE
Align.
SECOND
DIMPLE
6 mm
ROOF
PANEL
PROTECTIVE
TAPE
ROOF
PANEL
PROTECTIVE
TAPE
PROTECTIVE
TAPE
PROTECTIVE
TAPE
PROTECTIVE
TAPE
ROOF
PANEL
Clean with
isopropyl
alcohol.
SECOND
INDENTATION
ROOF
PANEL
Clean with isopropyl
alcohol.
Align.
FRONT
ROOF
PANEL
ROOF
PANEL
6 mm
ROOF
PANEL
8.
PROTECTIVE
TAPE
6 mm
PROTECTIVE
TAPE
SECOND
INDENTATION
SECOND
DIMPLE
Locate the dimples at the right front corner of the
moonroof opening. Remove the adhesive backing
from one protective tape. Starting at the second
dimple from the rear, wrap 6 mm of the protective
tape around the bottom lip of the roof panel opening.
Wrap the remaining portion of the protective tape up
around the top of the roof panel. Install a protective
tape to the left front corner of the moonroof opening
the same way.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
10. Locate the second indentation from the right front
corner of the moonroof opening. Remove the
adhesive backing from one protective tape. Starting
from the bottom edge of the second indentation,
wrap 6 mm of the protective tape around the lip of the
roof panel opening. Wrap the remaining portion of
protective tape up around the top of the roof panel.
Install the protective tape to the second indent on the
left side of the roof panel the same way.
AII 51570 (1405)
3 of 5
www.collegehillshonda.com
11. Place one bracket B over each outer protective tape,
and secure each bracket B in place with a piece of
masking tape.
PROTECTIVE
TAPE
12. Place one bracket A over each inner protective tape,
and secure each bracket A in place with a piece of
masking tape.
BRACKET A
PROTECTIVE BRACKET B
TAPE
Align.
FRONT
MASKING
TAPE
ROOF
PANEL
BRACKET B
PROTECTIVE
TAPE
BRACKET B
BRACKET A
BRACKET B
ROOF
PANEL
BRACKET B
Align.
PROTECTIVE
TAPE
PROTECTIVE
TAPE
PROTECTIVE
TAPE
MASKING
TAPE
BRACKET A
13. Align the holes in the moonroof visor with the holes
in brackets A and B. Secure the moonroof visor to
the brackets using the four screws and four nuts. Do
not tighten the screws at this time.
FRONT
MASKING TAPE
BRACKET B
BRACKET B
4 NUTS
2 BRACKETS A
MOONROOF
VISOR
BRACKET B
4 SCREWS
4 of 5
AII 51570 (1405)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
14. Adjust the position of the moonroof visor. Check that
all of the brackets are firmly snug against the
moonroof lip. Make sure the rubber molding on the
moonroof visor is not twisted or rolled under the
visor, and unfold if necessary.
CROSS SECTION
17. Remove the IMPORTANT INFORMATION label
from the moonroof visor.
IMPORTANT
INFORMATION
LABEL
Remove.
SCREW
MOONROOF
VISOR
NUT
Push.
PROTECTIVE
TAPE
BRACKET A
MOONROOF
VISOR
CARE OF THE MOONROOF VISOR
RUBBER
MOLDING
SCREW
• To avoid damaging the surface, never use
ammonia-based cleaners or solvents to clean the
moonroof visor.
RUBBER
MOLDING
• Clean with a solvent of mild dishwashing soap and
water using a soft cloth or chamois.
NUT
CROSS
SECTION
• To remove scratches and restore the original luster,
use Meguiar’s Mirror Glaze plastic cleaner and polish
or an equivalent high-quality plastic cleaner.
CROSS SECTION
BRACKET B
PROTECTIVE
TAPE
RUBBER
MOLDING
Unfold.
15. Tighten the screws and nuts while applying light
pressure against the brackets. Make sure that there
is no clearance between the brackets and the
moonroof visor. Using a torque screwdriver, torque
the screws and nuts: 2 N·m (1.5 lbf·ft).
16. Remove the masking tape and the shop towels.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
AII 51570 (1405)
5 of 5