4933 Bid Set.dwf - SRC Services, Inc.

Transcription

1
2
3
4
5
6
7
K
8
9
10
11
12
13
14
A Subsidiary of the Luxottica Group
4000 Luxottica Place
Mason, Ohio 45040
REMODEL
2.0 PREMIUM
CONSULTANT PROJECT150066
#
Shremshock Architects, Inc.
7400 W. Campus Rd. Suite 150 New Albany, OH 43054
t: 614 545 4550 | f: 614 545 4555 | shremshock.com
Gerald S. Shremshock, Architect
Timothy J. Shremshock, Architect
J
SEAL
FOR
RIVERCHASE GALLERIA
H
STORE #4933
2000 RIVERCHASE GALLERIA
BIRMINGHAM, AL 35244
SPACE #236A
G
IF REQ'D, STOCKROOM SHELVING TO BE UNDER
SEPARATE PERMIT, SUBMITTED BY SHELVING
MANUFACTURER.
DRAWING INDEX
F
DRAWING DESCRIPTION
SUNGLASS HUT
SPACE:#236A
LEVEL 2 OF 2
E
G-001
COVER SHEET
G-002
RESPONSIBILITY & DOOR SCHEDULE
A-101
DEMOLITION / LEASE PLAN
A-102
FLOOR PLAN
A-103
FINISH / FIXTURE PLAN
A-104
REFLECTED CEILING PLAN
A-201
ELEVATIONS
A-301
NOT USED
D
USER: PDICKERSON
STOREFRONT PLAN & ELEVATION
A-501
STOREFRONT DETAILS
A-502
GENERAL DETAILS
A-503
NOT USED
A-504
NOT USED
A-505
NOT USED
A-701
ARCHITECTURAL SPECIFICATIONS
A-702
ARCHITECTURAL SPECIFICATIONS
PROJECT CONTACTS
C
Project Manager
B
GENERAL GROWTH PROPERTIES, INC.
110 NORTH WACKLER DRIVE
CHICAGO,IL 60606
Contact:PHYLLIS WETHERALL
Phone: 312-960-5873
Store Planner
SYMBOLS LEGEND
Architect
LUXOTTICA
4000 LUXOTTICA PLACE
MASON, OH 45040
CONTACT: SHEILA HULL
PHONE: 513-765-3847
E-MAIL: [email protected]
SHREMSHOCK ARCHITECTS, INC.
7400 W. CAMPUS RD. SUITE 150
NEW ALBANY, OH 43054
CONTACT: JASON RICHARDSON
PHONE: 614-545-4550
2009 IBC
2009 IPC
2008 NEC
2009 IMC
2009 IECC
ICC.ANSI A117.1
USE GROUP:
CONSTRUCTION TYPE:
SEISMIC CATEGORY:
M-MERCANTILE
IIB, FULLY SPRINKLERED
B
SALES AREA:
NON-SALES AREA:
TOTAL:
601/30 = 21
57/30 = 2
23
EXITS REQUIRED:
EXITS PROVIDED:
1
1
WATER CLOSETS:
LAVATORIES:
Landlord
LUXOTTICA
MASON, OH 45040
CONTACT: SCOTT YOUNG
PHONE: 940-445-3122
BUILDING CODE:
PLUMBING CODE:
ELECTRICAL CODE:
MECHANICAL CODE:
ENERGY CODE:
ACCESSIBILITY:
TENNANT SEPARATION WALLS:1 HR
SALES/NON-SALES WALLS:
0 HR
CEILING:
0 HR
COLUMNS:
0 HR
NORTH
PLOTTED: 7/8/2015 - 4:45 PM
P:\SGH\150066 SGH-Riverchase Galleria Birmingham, AL\G-001_04933.dwg
LAYOUT: G-001
A-401
BUILDING CODE
THIS PROJECT IS A TENANT BUILD OUT OF A NEW
MERCANTILE SPACE IN AN EXISTING INTERIOR CENTER.
A1
SECTION ID
SHEET NUMBER
A-301
A1
ROOM
NAME
DETAIL ID
SHEET NUMBER
A-401
101
AT
LANDLORD NOTES
REV. 1
MALL KEY PLAN
-
DRINKING FOUNTAIN:
PUBLIC ACCESS:
SERVICE SINK:
E-101
POWER PLAN
E-102
LIGHTING PLAN & LIGHTING LEGEND
E-501
ELECTRICAL DETAILS, SYMBOLS & ABBREVIATIONS
E-601
ELECTRICAL SINGLE LINE DIAGRAM & PANEL SCHEDULES
E-701
ELECTRICAL SPECIFICATIONS
E-702
ELECTRICAL SPECIFICATIONS
-
1
1
NOT REQUIRED
NOT REQUIRED
NOT REQUIRED
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
NAME
NUMBER
SGH STORE #:4933
AREA CALCULATIONS
Purchasing Coordinator
MEP Consultant
LUXOTTICA
MASON, OH 45040
CONTACT: DAWN SPARKS
PHONE: 513-765-3947
1
A1
SHREMSHOCK ENGINEERING, INC.
7400 W. CAMPUS RD. SUITE 150
NEW ALBANY, OH 43054
CONTACT: JEROMY PERRY
PHONE: 614-545-4550
2
3
ELEVATION ID
SHEET NUMBER
A-201
4
LOCATION
ELEVATION
STOREFRONT FRONTAGE:
SHEET NUMBER
A-201
ELEVATION ID
A7
FLOOR
0'-0"
DRAWN BY:PWD
REVIEWED BY:RJH/JRM
A1
A
RIVERCHASE GALLERIA
SIGNAGE AND SPRINKLER PLAN TO BE SUBMITTED
UNDER SEPARATE COVER
RETAIL AREA
STOCK AREA:
NORTH
TOTAL:
LEASED TOTAL
1
1
5
6
AUTHORIZED FOR:
34 LF
601 SF
0 SF
COVER
SHEET
658 SF
766 SF
MATERIAL NUMBER
7
8
G-001
9
10
11
12
13
14
4
5
6
AMERICANS WITH DISABILITIES ACT
ACCESSIBILITIES GUIDELINES
ABOVE FINISH FLOOR
CENTERLINE
CEILING
CERAMIC TILE
COLUMN
CONCRETE
CONTINUOUS
DIAMETER
DIMENSION
DETAIL
DRAWINGS
ELECTRICAL CONTRACTOR
EXISTING
EXPOSED
EQUAL
FIXTURE CONTRACTOR
GYPSUM BOARD
GENERAL CONTRACTOR
A.F.F.
CL.
CLG.
CT.
COL.
CONC.
CONT.
DIA.
DIM.
DTL.
DWGS.
E.C.
EX. OR (E)
EXP.
EQ.
F.C.
G.B.
G.C.
J
G.A.T.
M.C.
N.I.C.
O.C.
OPP.
O/
P.C.
REQ.
R.
SCH.
SIM.
TYP.
U.N.O.
V.I.F.
VERT.
W.C.
WD.
W.R.
DOOR INFORMATION
MARK
H
T = TENANT/OWNER
G = GENERAL CONTRACTOR
L = LANDLORD
E = EXISTING
GYPSUM CEILING TILE
MECHANICAL CONTRACTOR
NOT IN CONTRACT
ON CENTER
OPPOSITE
OVER
PLUMBING CONTRACTOR
REQUIRED
RADIUS
SCHEDULED
SIMILAR
TYPICAL
UNLESS NOTED OTHERWISE
VERIFY IN FIELD
VERTICAL
WATER CLOSET
WOOD
WATER RESISTANT
ITEM
FRAME INFORMATION
LOCATION
NOMINAL SIZE
A1
(E) ENTRY
PR. 3'-0"W. x
8'-10"H. x 1/2"
ALUMINUM / GLASS
PREFIN.
ALUMINUM
PREFIN.
-
A
B1
SALES /
NON-SALES
3'-0"W. x 7'-0"H.
x 1 3/4"
HOLLOW METAL
P-3
HOLLOW METAL
P-3
-
B
(E) TOILET ROOM
3'-0"W. x 6'-8"H.
x 1 3/4"
HOLLOW METAL
P-4
HOLLOW METAL
P-4
-
C
(E) SERVICE
3'-0"W. x 7'-0"H.
x 1 3/4"
C1
D1
MATERIAL
HOLLOW METAL
FINISH
P-4
MATERIAL
HOLLOW METAL
FINISH
P-4
FIRE RATING
EXIST.
FURNISHED
BY
A.D.A.A.G.
K
7
- EXISTING TO REMAIN.
EXISTING TO REMAIN
LOCKSET: BOTTOM RAIL CYLINDER LOCK
C
- UNFI INISHED DOOR AND FRAME SUPPLIED, INSTALLED AND FINISHED BY G.C. (U.N.O.)
PRIVACY SET: CORBIN RUSSWIN MODEL #CL3620 NZD (LEVER STYLE); FINISH #BHMA 626 OR SCHLAGE EQUAL; PUSH BUTTON ON
INSIDE AND KEY ON OUTSIDE
LOCK CORES: BEST LOCK CORP.; 9K SERIES
DOOR CLOSER: CORBIN RUSSWIN DC4610 SERIES PARALLEL ARM WITH HOLD OPEN.
HINGES: BOMMER 1 1/2 PAIR PER LEAF, 4-1/2" x 4-1/2", NO. BB5004N STANDARD WEIGHT, AVERAGE FREQUENCY, FULL
MORTISE, BALL BEARING HINGE, FINISH STAINLESS STEEL
KICKPLATE: STANLEY DOOR SYSTEM; FULL WIDTH x 10"H x 1/8" STAINLESS STEEL INSTALLED 1" FROM BOTTOM OF DOOR
FLOOR MOUNTED STOP: IVES MODEL #FS13US26 CAST BRASS, CHROME PLATED (OR EQUAL)
SILENCERS: G.C. TO SELECT
F
USER: JYOUNG
D
SE
D
3'-0"
A1
1.
A
B1
7'-0"
6'-8"
7'-0"
8'-10"
B
3'-0"
3'-0"
NO
TU
3'-0"
SE
D
C
NO
TU
PLOTTED: 7/9/2015 - 10:43 AM
P:\SGH\150066 SGH-Riverchase Galleria Birmingham, AL\G-002_04933.dwg
LAYOUT: G-002
E
3'-0"
C1
D1
VERIFYING EXISTING DOOR HARDWARE TYPE AT LOCATIONS WHERE EXISTING EXTERIOR/ENTRANCE DOORS ARE TO REMAIN.
ANY NON-GENERIC/BRANDED DOOR HARDWARE TO BE IDENTIFIED AND REPLACEMENT MUST BE COORDINATED WITH
LUXOTTICA PROJECT MANAGER.
A1
SCALE:
10
11
HDWR.
D
NOTE:
VERIFY ALL ITEMS IN THIS SCHEDULE FOR ACCURACY PRIOR TO BEGINNING CONSTRUCTION. REPORT
ANY DISCREPANCIES TO THE PROJECT MANAGER IMMEDIATELY.
FURN. INST.
REMARKS
T
PERMIT APPLIED FOR BY TENANT / OBTAINED AND PAID FOR BY CONTRACTOR
TEMPORARY BARRICADES (WITH GRAPHIC)
T
T
TEMPORARY CONSTRUCTION WINDOW VINYL
T
T
DIVISION 03 - CONCRETE
FURN. INST.
REMARKS
CONCRETE SLAB
E
G.C. TO VERIFY AS REQUIRED
G.C. TO COORDINATE WITH LANDLORD BARRICADE VENDOR
FURN. INST.
STRUCTURAL STEEL
E
TENANT SEPARARTION WALL
E
DIVISION 08 - OPENINGS
FURN. INST.
STOREFRONT SYSTEM
E/T
STOREFRONT DOORS AND HARDWARE
E/G
E
REMARKS
14
THE CONTRACTOR SHALL HAVE EVIDENCE OF CURRENT WORKER'S COMPENSATION INSURANCE ON FILE IN
COMPLIANCE WITH LOCAL CODES.
2.
BEFORE COMMENCEMENT OF WORK, THE CONTRACTOR SHALL SHOW EVIDENCE OF ALL INSURANCE
REQUIREMENTS.
3.
THE CONTRACTOR SHALL BE FAMILIAR WILL ALL LANDLORD REQUIREMENTS AND SHALL BE RESPONSIBLE FOR
COMPLIANCE WITH REQUIREMENTS. THE CONTRACTOR SHALL INVESTIGATE LOCAL CODES AND PROCEDURES AND
SHALL COMPLY WITH REQUIREMENTS.
4.
SIGN CONTRACTOR TO OBTAIN SIGN PERMITS FROM BUILDING DEPARTMENT AS APPLICABLE.
5.
CONTRACTOR SHALL CONTACT LANDLORD REPRESENTATIVE BEFORE CONSTRUCTION COMMENCES.
6.
ALL CONDUIT, EQUIPMENT AND MATERIALS SHALL BE IN FULL ACCORDANCE WITH THE LATEST SAFETY RULES AND
REGULATION OF ALL AUTHORITIES AND AGENCIES HAVING JURISDICTION.
7.
THE CONTRACTOR SHALL MAINTAIN FOR THE ENTIRE DURATION OF THE WORK ALL EXITS, EXIT LIGHTING, FIRE
PROTECTION DEVICES AND ALARMS IN CONFORMANCE WITH ALL APPLICABLE CODES AND ORDINANCES.
8.
PROVIDE ADDITIONAL EXIT SIGNS AND FIRE EXTINGUISHERS IN TYPE , NUMBER, AND LOCATION AS DIRECTION BY
THE AUTHORITIES HAVING JURISDICTION.
SEE PLANS
9.
DURING ALL PHASES OF WORK DO NOT DISTURB THE DELIVERIES AND FUNCTIONS OF ADJACENT AND NEIGHBORING
TENANTS.
REMARKS
10. EACH CONTRACTOR SHALL LEAVE THE SITE IN A NEAT, CLEAN AND ORDERLY CONDITION UPON THE COMPLETION OF
THEIR WORK ON A DAILY BASIS. AREA OF WORK TO BE DUSTED, SWEPT AND MOPPED TO SAME CONDITION AS
START OF WORK. ALL WASTE OR EXCESS MATERIALS SHALL BE REMOVED FROM THE SITE PROMPTLY. THE G.C.
SHALL BE RESPONSIBLE FOR THE REMOVAL AND DISPOSAL OF ALL TRASH, INCLUDING TRASH GENERATED FROM
OWNER FURNISHED ITEMS AND BY OWNERS CONTRACTORS FOR THE DURATION OF THE PROJECT.
COORDINATE LOCKSMITH IF NOT COMPATIBLE WITH TENANT KEY SYSTEM
11. ALL EXISTING WORK NOT IN THIS SCOPE OF WORK SHALL BE MAINTAINED IN ITS ORIGINAL CONDITION, U.N.O.
E/T
T/G
13
1.
REMARKS
BUILDING PERMIT
DIVISION 05 - METALS
12
GENERAL NOTES
DIVISION 01 - GENERAL
DOOR LOCK CORES AND KEYS
T
DIVISION 09 - FINISHES
FURN. INST.
TENANT SEPARATION PARTITIONS (GYPSUM WALLBOARD)
E
E/G
G.C. TO VERIFY, PATCH/REPAIR AS REQUIRED
STOREFRONT BULKHEAD
E
E/G
G.C. TO VERIFY, PATCH/REPAIR AS REQUIRED
CEILING
E
E/G
14. G.C. SHALL BE RESPONSIBLE FOR COORDINATION WITH OWNERS REPRESENTATIVE TO PROVIDE A TIMELY ARRIVAL
OF ALL MATERIALS, EQUIPMENT AND OTHER SUCH ITEMS TO BE UTILIZED ON THIS PROJECT. G.C. SHALL NOTIFY
OWNER'S REPRESENTATIVE IN WRITING WITHIN 5 DAYS OF DATE OF APPROVED WORK AUTHORIZATION OF THOSE
ITEMS THAT MAY BY READILY AVAILABLE. IF NOTIFICATION IS NOT PROVIDED TO THE OWNER'S REPRESENTATIVE,
THE CONTRACT ACCEPTS RESPONSIBILITY FOR THE PROPER ORDERING AND FOLLOW-UP OF SPECIFIED ITEMS AND
WILL PURSUE WHATEVER MEANS NECESSARY AT NO ADDITIONAL COST TO OWNER.
1/8" GROUT JOINTS TYP.
15. CONTRACTOR TO ENSURE AVAILABILITY OF ALL SPECIFIED ITEMS SO AS NOT TO CREATE A HARDSHIP TO THE
OWNER AND NOT DELAY PROGRESS OF THE WORK. NO EXTENSION OF TIME SHALL BE PERMITTED.
REMARKS
2
3
4
CONSULTANT PROJECT # 150066
SEAL
13. WHEN CONTRACTOR ACCEPTS DELIVERY OF ALL ITEMS NOTED ON PLANS WHETHER IN CONTRACT OR NOT IN
CONTRACT, THE G.C. SHALL BE RESPONSIBLE FOR LOSS AND/OR DAMAGE TO THESE ITEMS.
T
G
GROUT
G
G
MALL FLOORING
E/L
L/G
ALUMINUM BASE MOULDING (HPL-06)
T
G
DIVISION 10 - SPECIALTIES
FURN. INST.
SIGNAGE
E/T
AWNING
-
DIVISION 12 - FURNISHINGS
FURN. INST.
REMARKS
MILLWORK FLOOR FIXTURES
T
T
G.C. TO COORDINATE WITH VENDOR
U-RAIL GRAPHIC HANGING SYSTEM (TBD)
T
G
LOOSE FIXTURES/PROPS
T
T
G.C. TO COORDINATE WITH VENDOR, G.C. TO UNBOX, UNWRAP AND STORE IN B.O.H.
MISCELLANEOUS EQUIPMENT
T
G
SEE EQUIPMENT SCHEDULE
GRAPHICS GRID
T
G
16. CONTRACTOR SHALL BE RESPONSIBLE TO RECEIVE, INVENTORY, STORE, AND SECURE ANY OWNER FURNISHED
ITEMS SUPPLIES AND DELIVERED TO THE JOBSITE, OR OTHER AGREED UPON LOCATION, AND FORWARD THE
RECEIVING DOCUMENTS TO THE OWNER.
REMARKS
17. NO MATERIAL SUBSTITUTIONS WILL BE ALLOWED UNLESS NOTED OTHERWISE OR SUBMITTED IN WRITING TO AND
APPROVED BY THE OWNER'S REPRESENTATIVE.
T
G.C. TO COORDINATE WITH VENDOR
18. ANY WOOD CONSTRUCTION SHALL BE FIRE RETARDANT TREATED, U.N.O.
-
N/A
19. G.C. SHALL VISIT THE SITE PRIOR TO SUBMITTAL OF BID TO DETERMINE CONDITIONS AFFECTING THE WORK. ANY
ITEMS WHICH ARE NOT COVERED IN THE BID DOCUMENTS OR ANY PROPOSED SUBSTITUTIONS SHALL BE LISTED
SEPARATELY AND QUALIFIED IN THE CONTRACTOR'S BID. SUBMITTAL OF BID SHALL SERVE AS EVIDENCE OF
KNOWLEDGE OF EXISTING CONDITIONS AND ANY MODIFICATIONS WHICH ARE REQUIRED TO MEET THE INTENT OF
THE DRAWINGS AND SPECIFICATIONS. FAILURE TO VISIT THE SITE DOES NOT RELIEVE THE CONTRACTOR OR
RESPONSIBILITY IN PERFORMANCE OF WORK.
20. ALL CONTRACTORS, SUBCONTRACTORS, VENDORS AND MATERIAL SUPPLIES SHALL BE RESPONSIBLE FOR
REVIEWING THE COMPLETE SET OF DOCUMENTS AS SHOWN IN THE SHEET INDEX. FAILURE TO REVIEW
CONSTRUCTION DOCUMENTS WILL NOT RELIEVE ANY CONTRACTORS, SUBCONTRACTORS, VENDORS OR MATERIAL
SUPPLIES FOR PERFORMING WORK OR PROVIDING MATERIALS REQUIRED FOR THE COMPLETION OF THIS PROJECT
AS DEFINED WITHIN THE DOCUMENTS AT TIME OF BID.
TOILET ACCESSORIES
G
DIVISION 21 - FIRE SUPPRESSION
FURN. INST.
SPRINKLER SYSTEM MODIFICATIONS
E
E
FIRE SPRINKLER MAIN
E
E
DIVISION 22 - PLUMBING
FURN. INST.
WATER AND SEWER STUB
E
E
24. DO NOT SCALE DRAWINGS. WRITTEN DIMENSIONS TAKE PRECEDENCE OVER SCALED DRAWINGS.
WATER METER
E
E
GAS METER
E
E
25. ARCHITECTURAL DRAWINGS TAKE PRECEDENCE OVER OTHER DRAWINGS FOR LAYOUT DIMENSIONS AND NUMBER
OF ITEMS PROVIDED. UPON DISCOVERY OF DISCREPANCIES BETWEEN ARCHITECTURAL DRAWINGS AND
ENGINEERING DRAWINGS, OWNER SHALL BE IMMEDIATELY NOTIFIED IN WRITING.
PLUMBING FIXTURES
E
E
DIVISION 23 - HEATING, VENTILATING, AND AIR CONDITIONING
FURN. INST.
G
AIR CURTAIN
E
E
EXHAUST FANS AND VENTING
E
E
HVAC UNIT
E
E
HVAC CONTROLS
E
E
21. G.C. SHALL COORDINATE WORK PERFORMED BY OTHER CONTRACTORS. ANY DISCREPANCIES SHALL BE BROUGHT
TO THE OWNER'S ATTENTION (VERBALLY AND DOCUMENTED IN WRITING) BEFORE PROCEEDING WITH WORK.
REMARKS
22. SHOULD A CONFLICT EXIST BETWEEN THE CONSTRUCTION DOCUMENTS AND/OR THE SPECIFICATIONS, THE
OWNER'S REPRESENTATIVE SHALL BE INFORMED (VERBALLY AND DOCUMENTED IN WRITING) OF THIS DISCREPANCY
IMMEDIATELY, AT WHICH TIME OWNER'S REPRESENTATIVE SHALL PROVIDE DIRECTION ON HOW TO PROCEED.
23. INSPECT SITE AND VERIFY FIELD DIMENSIONS BEFORE COMMENCING WITH CONSTRUCTION. NOTIFY OWNER'S
REPRESENTATIVE AND LANDLORD IMMEDIATELY IF THERE ARE ANY DISCREPANCIES.
REMARKS
26. IF ANY ERRORS OR OMISSIONS APPEAR IN THE CONTRACT DOCUMENTS, CONTRACTOR SHALL NOTIFY OWNER IN
WRITING OF SUCH ERRORS OR OMISSIONS.
27. DIMENSIONS SHOWN ON PLANS ARE TO FACE OF CMU, CONCRETE COLUMNS OR GRID LINES AND FACE OF
GYPSUM BOARD UNLESS NOTED OTHERWISE.
REMARKS
28. THE CONTRACTOR SHALL REVIEW ALL CONSTRUCTION DOCUMENTS, VERIFY ALL DIMENSIONS AND FIELD
CONDITIONS AND CONFIRM WORK IS BUILDABLE AS SHOWN. ANY CONFLICTS OR OMISSIONS, ETC. SHALL BE
IMMEDIATELY REPORTED TO THE ARCHITECT FOR CLARIFICATION PRIOR TO PERFORMANCE OF ANY WORK IN
QUESTION.
29. COLUMN CENTER LINE (OR GRID LINES) ARE SHOWN FOR DIMENSIONS. VERIFY EXACT LOCATION IN FIELD.
ENERGY MANAGEMENT SYSTEM (EMS)
-
-
HVAC DISTRIBUTION DUCTWORK, DIFFUSERS
E
E
CURBS & SUPPORTS FOR CONDENSING UNITS
-
-
N/A
SMOKE EVACUATION SYSTEM & CONTROLS
E
E
-
DUCT SMOKE DETECTORS
-
-
N/A
DIVISION 26 - ELECTRICAL
FURN. INST.
ELECTRICAL SERVICE, CONDUIT, WIRING
E/G
E/G
ELECTRIC METER, SEPARATE
E/G
E/G
ELECTRICAL PANELS
E/G
E/G
TRACK CURRENT LIMITING PANEL
-
-
EMERGENCY LIGHTING
E/T
E/G
EXIT SIGNS
E/T
E/G
FIRE ALARM SYSTEM
-
-
LIGHT FIXTURES
E/T
E/G
LAMPS
E/T
E/G
SOUND SYSTEM & SPEAKERS
T
T
COORDINATE WITH VENDOR
TENANT TELEPHONE EQUIPMENT
T
T
TELEPHONE CONDUIT TO SPACE
L/E
TELEPHONE WIRING TO SPACE
L/E
SECURITY - FACILITY/HARDWARE & WIRING/VECTOR (ALARMS)
T
T
SECURITY - PRODUCT/HARDWARE & WIRING/- A1 (CAMERAS)
T
T
TRAFFIC COUNTER
T
T
N/A
30. OWNER'S REPRESENTATIVE AND TENANT ARE THE SAME FOR PURPOSES OF THESE DRAWINGS.
31. ALL OPENINGS, FLASHING, COUNTER FLASHING, AND EXPANSION JOINTS SHALL BE WATERTIGHT IN EXTERIOR
STORES.
32. ALL OPEN JOINTS, PENETRATIONS AND OTHER OPENINGS IN THE BUILDING ENVELOPE SHALL BE SEALED, CAULKED,
GASKETED OR WEATHER-STRIPPED TO LIMIT AIR LEAKAGE IN EXTERIOR STORES.
33. ALL SAW CUTTING AND CORING LOCATIONS SHALL BE REVIEWED AND COORDINATED WITH THE LANDLORD PRIOR TO
CUTTING/ CORING.
REMARKS
34. G.C. IS RESPONSIBLE FOR MAINTAINING REQUIRED FIRE RATINGS AND FIRE PROOFING IN ALL INSTANCES.
35. GC TO COVER THE STOREFRONT WINDOWS AND DOORS WITH KRAFT PAPER FROM THE TIME THE BARRICADE IS
REMOVED UNTIL THE STORE OPENS.
36. GC TO SCHEDULE A PRE-TURNOVER CLEANING FOR WEDNESDAY MORNING AND A FINAL DETAIL CLEANING TUESDAY
MORNING AT 9:00 AM PRIOR TO OPENING.
37. TIMECLOCK TO BE SET TO "ON" 30 MINUTES PRIOR TO MALL OPENING AND 30 MINUTES AFTER MALL CLOSE.
38. INSTRUCTIONS FOR MODIFYING THE TIMECLOCK OPERATION TO BE LEFT WITH THE STORE AND DETAILED
MANAGEMENT AT TURNOVER.
39. GC IS RESPONSIBLE TO ACCEPT DELIVERY OF ALL PROPS - UN-BOX, SORT AND COUNT. THE SUPERINTENDENT
SHOULD GIVE A CHECK-IN SHEET NOTING ALL DISCREPANCIES TO THE PROJECT MANAGER UPON ARRIVAL FOR THE
PUNCHLIST.
40. ALL CARDBOARD SHOULD BE REMOVED FROM THE SITE PRIOR TO TURNOVER, HOWEVER, THE PROPS SHOULD BE
LEFT IN THE PLASTIC TO PROTECT FROM DAMAGE/DUST.
5
6
7
8
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
DRAWN BY: PWD/CBV/XXX
REVIEWED BY: RJH
AUTHORIZED FOR:
RESPONSIBILITY &
DOOR SCHEDULE
G-002
DOOR SCHEDULE
1
Mason, Ohio 45040
12. PROTECT WORK FROM DAMAGE RESULTING FROM THIS WORK.
CERAMIC TILE FLOORING
A
9
STOREFRONT TILE
G.C. TO REPLACE ANY MISSING OR DAMAGED HARDWARE
G
8
RESPONSIBILITY SCHEDULE
AT
3
RIVERCHASE GALLERIA
2
ABBREVIATIONS
INSTALLED
BY
1
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GENERAL NOTES
1.
TAKE ALL NECESSARY PRECAUTIONS TO ENSURE THE SAFETY OF THE PUBLIC
AND/OR WORKERS ON THE JOB AND TO PREVENT ACCIDENTS OR INJURY TO ANY
PERSON ON, ABOUT, OR ADJACENT TO THE PREMISES. COMPLY WITH ALL LAWS,
ORDINANCES, CODES, RULES AND REGULATIONS RELATIVE TO SAFETY AND THE
PREVENTION OF ACCIDENTS.
2. THIS DEMOLITION PLAN IS TO BE USED IN CONJUNCTION WITH THE ENTIRE SET OF
WORKING DRAWINGS. DO NOT REMOVE OR DEMOLISH ANYTHING WITHOUT
VERIFYING AND COORDINATING WITH ALL GENERAL TRADES AS TO HOW THEY
RELATE TO THE OVERALL PROJECT.
3. ALL CONTRACTORS SHALL BE RESPONSIBLE FOR DEMOLISHING AND REMOVING
EXISTING CONSTRUCTION WHICH WILL INTERFERE WITH THEIR NEW WORK AND ANY
TEMPORARY BRACING OR PERMANENT SUPPORT STRUCTURES.
4. WHEN EXISTING ELECTRICAL SERVICE, POWER, AND LIGHTING IS REMOVED, STUB
BACK AND CAP AS REQUIRED IN AREAS BETWEEN EXISTING CONDITIONS AND NEW
WORK.
5. ANY EXISTING ROOFTOP AIR CONDITIONING UNIT, ROOF CURBS AND ALL
ASSOCIATED DUCTWORK, GRILLES, DIFFUSERS, HANGER, CONTROL WIRING,
ELECTRICAL WIRING, CONDUITS, AND CONDUIT HANGERS, IF APPLICABLE PER
PROJECT STORE SITE, TO REMAIN UNLESS NOTED OTHERWISE ON PLANS. REFER
TO MECHANICAL DRAWINGS.
6. IN ACCORDANCE WITH THE DRAWINGS, THOSE ITEMS WHICH ARE REMOVED, AND
ARE NOT RELOCATED OR REUSED, SHALL BE DISPOSED OF BY THE G.C.
7. PROVIDE AND INSTALL TEMPORARY BARRICADE. COORDINATE REQUIREMENTS
WITH LANDLORD.
ELEVATION SHOWN IS A REPRESENTATION OF INTENT. ACTUAL VINYL
GRAPHIC ARTWORK IS TO BE SUBMITTED TO LANDLORD FOR REVIEW BY
THE SUNGLASS HUT'S MARKETING DEPARTMENT FOR APPROVAL PRIOR
TO PRODUCTION AND INSTALLATION.
K
TENANT TO SUPPLY GRAPHICS. COORDINATE WITH
LANDLORD BARRICADE SIGNAGE REQUIREMENTS
TURN IN
BARRICADE
TURN IN
BARRICADE
TURN IN
BARRICADE
12'-0"± A.F.F.
T.O. BARRICADE
J
Mason, Ohio 45040
SEAL
TEMPORARY BARRICADE
0'-0" A.F.F.
H
1.
BOSTON BARRICADE SHALL CONSTRUCT A TEMPORARY BARRICADE PER LL
REQUIREMENTS.
2.
BARRICADE IS TO BE 100% COMPLETE AND READY FOR GRAPHICS TO BE
INSTALLED NOT MORE THAN TWO DAYS AFTER CONSTRUCTION START. G.C. TO
CONTACT OWNERS REPRESENTATIVE UPON COMPLETION TO COORDINATE
GRAPHICS INSTALLATION.
3.
G.C. IS RESPONSIBLE FOR MAINTAINING BARRICADE DURING CONSTRUCTION.
FINISH FLOOR
BARRICADE PROVIDED
BY BOSTON BARRICADE
20'-73 8"±
6'-114"±
(UNFOLDED)
16'-114"±
(UNFOLDED)
6'-114"±
(UNFOLDED)
4. REMOVE BARRICADE WHEN 100% OF STOREFRONT IS COMPLETE ON THE EVENING
BEFORE G.C.'S PUNCHLIST IS COMPLETED, PRIOR TO OWNER VERIFICATION, AND
AFTER LANDLORD APPROVAL IS RECEIVED. CARE IS TO BE TAKEN WHEN
DISASSEMBLING AND REMOVING BARRICADE. ON INTERIOR SIDE (STORE SIDE),
PAPER WINDOWS WITH WHITE CONSTRUCTION PAPER OVER GLAZING ONLY. TRIM
1/2" OFF EDGES AND TAPE CONTINUOUSLY AROUND PERIMETER WITH WHITE TAPE.
G.C. IS TO RESTORE NEUTRAL PIER(S), MALL FLOORING AND BULKHEAD TO A 'LIKE
NEW' CONDITION AND FINISH.
G
G1
SCALE:
BARRICADE ELEVATION
2'-07 8"
L.L. TO L.L.
35'-312"
L.L. TO L.L.
F
J
H
17'-63 8"
5'-918"
12'-0"
2'-63 8"
L.L. TO L.L.
22
10
4
12
9
15
26
S
C
20
C1
8
3
1
26
S
C
4'-0"
CUSTOM
FILLER
PANEL
10
18
25
19
FROM LEASE
LINE
S
C
15
4
6
S
LEASE LINE.
5.
EXISTING STOREFRONT SIGNAGE TO BE RELOCATED ONCE RECLADDING HAS BEEN
FINISHED.
6.
REMOVE EXISTING FLOORING MATERIAL. PATCH AND PREPARE FLOOR AS REQ'D TO
PROVIDE SMOOTH FLOOR FOR NEW FLOORING PER PLAN ON SHEET A-103. CAP
EXISTING MECHANICAL, PLUMBING AND ELECTRICAL SERVICES FLUSH WITH EXISTING
SLAB AS REQ'D.
7.
EXISTING PENDANT LIGHTING TO BE REMOVED.
11. EXISTING GYPSUM BOARD CEILING TO REMAIN, PATCH AND REPAIR AS REQUIRED.
13. ALL EXISTING PLUMBING FIXTURES TO REMAIN U.N.O.
14. EXISTING ELECTRICAL PANEL TO REMAIN.
A1
10
8
15. EXISTING LIGHTING, CEILING DEVICES, ACCESS PANELS, SOFFITS AND CEILING
SYSTEM TO REMAIN, U.N.O. REFER TO ELECTRICAL DRAWINGS.
BARRICADE BY BOSTON BARRICADE.
REFER TO VENDOR SHOP DRAWINGS
16. PENDANTS TO BE REMOVED, U.N.O. SEE SHEET A-104.
21
S
C
2'-0"
21
5
17. EXISTING FLOOR OUTLETS TO REMAIN.
COL
18. EXISTING SMOKE DETECTOR TO REMAIN,
19. EXISTING SPEAKER TO BE RELOCATED.
14
ADJACENT
TENANT (N.I.C.)
REMOVE EXISTING TRACK AND FIXTURES.
10. EXISTING DOOR TO REMAIN. CLEAN TO "LIKE NEW" CONDITION.
25
(E
)
26
C
8. EXISTING SOFFITS TO REMAIN.
9.
12. EXISTING WALL TO REMAIN.
11
17
26
OVERALL LEASE LINE
3
S
FE
21. EXISTING MALL COLUMN TO REMAIN.
LEASE LINE
9
3
B
22. LIGHTING PANEL TO BE REMOVED AND RELOCATED. REFER TO ELECTRICAL SHEETS.
MALL
COMMON AREA
1
RIVERCHASE GALLERIA
20. EXISTING SPEAKER TO REMAIN.
4
23. TRANSFORMER TO BE RELOCATED ABOVE CEILING. REFER TO ELECTRICAL SHEETS.
G1
26. EXISTING SLOT DIFFUSERS TO REMAIN
A-101
8
'-2
7
25. EXISTING RECESSED LIGHTS TO BE REMOVED
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
27. EXISTING GRAB BAR TO REMAIN.
DRAWN BY: PWD
VE
16
"L
.L
.T
O
1
L.L
RA 8'.
LL 11 1
LE 2 "
AS
E
LIN
E
24. EXISTING PHONE BOARD TO REMAIN.
REVIEWED BY: RJH/JRM
O
GRAPHICAL KEY
AUTHORIZED FOR:
EXIST. TO BE REMOVED U.N.O.
EXIST. TO REMAIN U.N.O.
L. 2 'L. 8 5
TO 8
"
L.
L.
LAYOUT: A-101
P:\SGH\150066 SGH-Riverchase Galleria Birmingham, AL\A-101_04933.dwg
2
"
-0
4'
PLOTTED: 7/9/2015 - 8:22 AM
18
REMOVE EXISTING CASHWRAP, FLOOR CASEWORK, AND ASSOCIATED ELECTRICAL &
DATA HOOK-UP. REMOVE WIRING/ CONDUIT BACK TO SOURCE.
3.
7
(E)
12
"
.
5 8
.L
'-9 L L
3 1 RA L
VE
O
USER: PDICKERSON
24
(E) GLAZING ASSEMBLY & FRAMING TO REMAIN. CLEAN TO "LIKE NEW" CONDITION.
(E) STORE FRONT FINISHES TO BE REMOVED. AS REQUIRED TO ACCOMMODATE
INSTALLATION OF NEW FINISH MATERIALS.
2.
4. EXISTING MILLWORK TO BE REMOVED.
9
13
S
C
D
4
8
14'-53 8"
3
11'-11" L.L. TO L.L.
3'-107 8"
OVERALL L.L.
E
3
27
17'-718"
14
1.
AT
KEY NOTES
ADJACENT
TENANT (N.I.C.)
23
RIVERCHASE GALLERIA
37'-43 8"
OVERALL LEASE LINE
A
NORTH
A1
SCALE:
A-101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
3
4
5
ACCESSORY
ID
DESCRIPTION
8
1
GRAB BAR
B-5806x42
BOBRICK
GRAB BAR
B-5806x36
BOBRICK
3
VERTICAL GRAB BAR
B-5806x18
BOBRICK
4
MIRROR
B-165 1836
BOBRICK
ABOVE LAV. REFER TO G6/A-502
5
MIRROR
B-165 2460
BOBRICK
RESTROOM DOOR
6
TOILET TISSUE DISPENSER
B-5543
BOBRICK
NON-LOCKING
7
UTILITY HOOK
B-2116
BOBRICK
HOOK STRIP
B-232x24
9
MOP HOLDER
B-223x24
BOBRICK
PAPER TOWEL DISPENSER
KT1024
SIMPLE HUMAN
11
LAVATORY FAUCET
7038.101
AMERICAN STANDARD
MODEL #
MANUFACTURER
LOCKERS(#)
EMPLOYEE LOCKERS
36168/
36368
LOCKERS.COM
SAFE
SMALL DROP SLOT SAFE
UC-025K
SENTRYSAFE
MICRO
MICROWAVE OVEN
M01108SST
AVANTI
FRIDGE
REFRIGERATOR
RM3316B
AVANTI
XxYxZ
PIPP SHELVING
STORAGE SHELVING
PIPP
11
COLOR: GRAY, LOCKS: 33390, # =
NUMBER OF 12" WIDE UNITS
TO BE LOCATED IN CASHWRAP
COLOR: BLACK
X = WIDTH, Y = DEPTH, Z = HEIGHT,
SEE A7/A-502
8.
GRAB BAR
MIRROR
(N)
TOILET TISSUE
DISPENSER
(N)
SE
D
SE
D
HOOK
STRIP
14
10.
11.
COORDINATE CORE DRILLING WITH MALL OPERATIONS MANAGER PRIOR TO
BEGINNING WORK.
PREPARE THE FLOOR SLAB AND PROCURE MATERIALS REQUIRED AT THE ENTRANCE
TO PRODUCE A FLUSH CONDITION BETWEEN THE TENANT STORE CLOSURE LINE
AND THE EXISTING MALL FLOORING.
INSTALL ALL FINISH FLOORING (I.E.: CARPET, WOOD, TILE) AND ALL FINISH WALL
MATERIALS BEHIND AND UNDER ALL MILLWORK.
ADEQUATE ACCESS PANELS OR DOORS SHALL BE INCORPORATED INTO TENANT
WORK FOR INSPECTION SERVICE AND REPLACEMENT OF BOTH LANDLORD AND
TENANT EQUIPMENT, COORDINATE PLACEMENT WITH LANDLORD'S ON-SITE
REPRESENTATIVE.
PROVIDE 3/4" FIRE RETARDANT PLYWOOD BEHIND ALL ELECTRICAL AND TELEPHONE
PANELS, PAINT TO MATCH WALL COLOR FINISH PRIOR TO HARDWARE
INSTALLATION.
PROVIDE EXPANSION BETWEEN ALL NEW WALLS AND THE EXISTING ROOF
STRUCTURE ABOVE.
PATCH/REPAIR ALL SURFACES (WALLS, FLOOR, CEILING, ETC.) AFFECTED BY
DEMOLITION WORK.
TRANSITIONS BETWEEN DISSIMILAR FLOOR MATERIALS TO BE SMOOTH AND
FLUSH. REFER TO SHEET A-502 FOR FOR APPLICABLE FLOOR TRANSITION
DETAILS.
ALL FINISH MATERIALS SHALL BE INSTALLED PER MANUFACTURER'S STANDARD
WRITTEN DETAILS AND SPECIFICATIONS. REFER TO SPECIFICATIONS FOR
ADDITIONAL INFORMATION.
PROVIDE A LEVEL 4 GYP. BD. FINISH ON ALL NEW AND EXISTING WALLS.
SEAL CONTROL JOINTS IN CONCRETE FLOORS.
Mason, Ohio 45040
SEAL
4'-0"
6'-0"
4'-0"
UTILITY
HOOK
(N)
13
NO
TU
1'-7"
MIN.
MIRROR
(E)
NO
TU
6'-2"
7"-9"
9.
SE
D
PLAN VIEW
NO
TU
1'-4" MIN
1'-6" MAX
EQUIPMENT SCHEDULE
3'-4"
NO
TU
NO
3'-0"
GRAB BAR
(E)
SE
D
SE
D
TU
3'-4"
3'-4"
TU
NO
3'-0"
GRAB BAR
(N)
4.
7.
SCALE:
SE
D
3'-0"
MIN
CL
2'-0" 12"
MIN MIN
1'-0"
2.
6.
J8
3'-6"
1.
3.
STAPLES #180969
TOILET ACCESSORY SCHEDULE
H
12
GENERAL NOTES
REMARKS
BOBRICK
J4
G
10
DESCRIPTION
5.
10
SCALE:
9
EQUIPMENT
NAME
REMARKS
2
8
J
7
MANUFACTURER
4'-0"
K
6
MODEL #
NO
TU
2
SE
D
1
MOP
HOLDER
(N)
PAPER TOWEL
DISPENSER
(E)
G4
SCALE:
TOILET ACCESSORY MOUNTING HEIGHTS
ADJACENT
TENANT (N.I.C.)
J
17'-63 8"
H
3
2'-63 8"
L.L. TO L.L.
102
1
3
EXISTING TENANT SEPARATION WALL TO REMAIN. G.C. SHALL PATCH/ REPAIR GYP
BD. AS REQUIRED. MAINTAIN REQUIRED RATING.
4.
CONCRETE MUST BE LEVEL AND CLEAN OF ANY FOREIGN MATERIALS PRIOR TO
INSTALLING NEW FINISHED FLOORING. G.C. TO PERFORM MOISTURE BARRIER
TEST BEFORE INSTALLING ANY FLOORING - REFER TO SPECIFICATIONS FOR
MOISTURE TEST PROCEDURES
5.
LINE OF SOFFIT ABOVE.
6.
EXISTING ELECTRICAL DISTRIBUTION EQUIPMENT. REFER TO ELECTRICAL
DRAWINGS.
7.
NOT USED.
8. NOT USED.
17'-718"
4
1
14'-53 8"
5
100
D
2
5
SALES
5
OVERALL LEASE LINE
9.
(E)
14
11'-11" L.L. TO L.L.
C1
6
NOT USED.
10. NOT USED.
11. NOT USED.
E8
12. NOT USED.
A-401
13. NOT USED.
14. EXISTING PHONE BOARD.
15. NOT USED.
5
C
(E
)
1
16. RELOCATED TRANSFORMER ABOVE.
A1
MALL COMMON
AREA (N.I.C.)
2'-0"
5
3
COL
14
5
LEASE LINE
OVERHEAD LINEWORK
WALL CONSTRUCTION
WALL INFILL CONSTRUCTION
EXISTING WALL CONSTRUCTION
A1
8
"L
.L
.T
O
18
L.
'
L.
LL -11 1
LE 2 "
AS
E
LIN
E
RA
O
16
'-2
7
2
VE
B
RIVERCHASE GALLERIA
GRAPHICAL KEY
1
ADJACENT
TENANT (N.I.C.)
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
DOOR WITH TYPE AND SIZE - SEE G-002 & D4/A-502
DRAWN BY: PWD
E1
(E)
A1
A-401
EXISTING DOOR WITH TYPE AND SIZE - SEE G-002
AUTHORIZED FOR:
X
L. 2 '
L . -8 5
TO 8
"
L.
L.
PLOTTED: 7/9/2015 - 9:03 AM
EXISTING STOREFRONT SYSTEM.
3.
1
"
.
5 8
.L
'-9 L L
3 1 RA L
VE
O
LAYOUT: A-102
3'-107 8"
OVERALL L.L.
E
USER: PDICKERSON
LEASE LINE.
2.
5'-918"
12'-0"
TOILET
ROOM
16
1.
AT
F
KEY NOTES
2'-07 8"
L.L. TO L.L.
35'-312"
L.L. TO L.L.
RIVERCHASE GALLERIA
37'-43 8"
OVERALL LEASE LINE
A
NORTH
FE
PARTITION TYPE - SEE A8/A-503
FIRE EXTINGUISHER. FOR EXACT LOCATIONS AND REQUIREMENTS
CONSULT WITH LOCAL FIRE DEPARTMENT INSPECTOR
FLOOR PLAN
A1
SCALE:
A-102
FLOOR PLAN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
FLOOR
K
J
GR-01
GROUT FOR CERAMIC TILE
LATTICRETE
COLOR:45 RAVEN
T-02
CERAMIC TILE
ATLAS CONCORDE
ATLAS CONCORDE EVOLVE
COLOR: EVOLVE IRON
FINISH: MATTE
SIZE: 60x60 - 23 5/8”x23 5/8”
GROUT SPACING: 1/8"
VT-01
VINYL TILE
ARMSTRONG COMMERCIAL FLOORING
STANDARD EXCELON IMPERIAL TEXTURE
COLOR: 51861 SOFT WARM GRAY
SIZE: 12" x 12" x 1/8"
5
6
P-3
ACRYLIC PAINT
BENJAMIN MOORE
REGAL SELECT
COLOR: 2132-10 BLACK
SHEEN: SEMI-GLOSS
P-4
ACRYLIC PAINT
BENJAMIN MOORE
REGAL SELECT
COLOR: PM-1 SUPER WHITE
SHEEN: SEMI-GLOSS
P-6
ACRYLIC PAINT
BENJAMIN MOORE
REGAL SELECT
COLOR: 2126-60 ANCHOR GRAY
SHEEN: FLAT
7
8
9
10
11
12
13
14
GENERAL NOTES
1.
PROVIDE AND INSTALL FIRE EXTINGUISHERS AS DIRECTED BY THE FIRE MARSHAL.
(SUGGESTED LOCATIONS ON PLAN. IF EXISTING AND NOT CURRENT, CONTACT P.M.
2.
EXAMINE ALL SURFACES TO BE PAINTED UNDER THIS CONTRACT AND SEE THAT THE
WORK OF OTHER TRADES HAVE BEEN LEFT OR INSTALLED IN A SATISFACTORY
CONDITION TO RECEIVE PAINT OR SPECIFIED FINISH.
3.
MAINTAIN ALL FINISHES IN THE STORE, WALLS, FLOOR AND CEILING PRIOR TO
TURNOVER. TOUCH-UP ALL CORNER BEADS, WALLS, CEILING AND FLOORING AS
REQUIRED PRIOR TO TURNOVER AND ANY DAMAGE CAUSED BY OTHER TRADES
INCLUDING MILLWORKER.
4.
SEE SHEET A-201 FOR SALES ELEVATIONS AND FINISH DESIGNATIONS.
5.
G.C. TO CLEAN EXISTING FLOORING TO 'LIKE NEW' CONDITION.
Mason, Ohio 45040
STOREFRONT
MET-01
BASE
HPL-06
DECOMETAL LAMINATE APPLIED TO WOOD BASE.
FORMICA
FINISH: BRUSHED ALUMINIUM
VB-01
VINYL BASE
JOHNSONITE
4" H. x 1/8" THICK
COLOR: 38-PEWTER
ALUMINUM BRAKE METAL
RETAIL STOREFRONT GROUP
#063 ALUMINUM
COLOR: TRANSFER BLACK
FINISH: SEMI-GLOSS
SEAL
WALL
P-1
ACRYLIC PAINT
BENJAMIN MOORE
REGAL SELECT
COLOR: 2132-10 BLACK
SHEEN: EGGSHELL
P-2
ACRYLIC PAINT
BENJAMIN MOORE
REGAL SELECT
COLOR: PM-1 SUPER WHITE
SHEEN: EGGSHELL
H
KEY NOTES
1.
H.C. ACCESSIBLE CASHWRAP.
6.
SIGNAGE ABOVE. REFER TO ELEVATIONS.
7.
(54) PRODUCT STORAGE TRAYS. FURNISHED BY OWNER, INSTALLED BY G.C.
NOT USED.
11. NEW MOP HOLDER. REFER TO J4/A102 FOR ADDITIONAL INFORMATION
FINISH MATERIAL SCHEDULE
12. NOT USED.
J
15. NEW RETRACTABLE LAVATORY FAUCET. REFER TO J4/A102 FOR ADDITIONAL
INFORMATION.
16. CUSTOM FILLER PANEL
H
5'-918"
12'-0"
ADJACENT
TENANT (N.I.C.)
8
812"
SP 10.8R
SP 14.0-4
SP 10.5L
ACCESSORY
6
1'-6"
17'-718"
SP 10.5R
A-201 E1
4'
-0
"
100
EQ
.
A-201
3'-0"
SALES
6
H1
14
H6
EQ
.
-1
CT
SP
3'
-0
"
6
3
RIVERCHASE GALLERIA
W
IN
D
O
W
"
'-6
EQ
COL
14
J6
SP
11
.5
R
"
'-2
"
.
5 8
.L
'-9 L L
3 1 RA L
VE
O
SP
6)
(3
11
.5
L
5
5.
13
1
C
2'-0"
"
'-0
7
ADJACENT
TENANT (N.I.C.)
MALL COMMON
AREA (N.I.C.)
CW 3.1L
E6
CUSTOM
FILLER
PANEL
TH
EM
E
"
4'
-0
15
-2
CT
8)
(1
102
.4
11
TOILET
ROOM
SP
11
D
3'
-6
"
4'
-0
"
A1 A-201
T 02
GR 01
14'-53 8"
5
J9
OVERALL LEASE LINE
SP 10.5L
10
11'-11" L.L. TO L.L.
4
SP 10.0 ST
SP 10.5R
2'-0"
2
7
SP 10.5L SP 10.4(18)
STOREFRONT
16
18"
MIN.
ADJACENT
TENANT (N.I.C.)
3'-6"
3'-107 8"
OVERALL L.L.
E
AT
17'-63 8"
2'-63 8"
L.L. TO L.L.
F
14. SALES FLOOR MIRROR PROVIDED & INSTALLED BY MILLWORKER. G.C. TO PROVIDE
BLOCKING AS REQUIRED.
2'-07 8"
L.L. TO L.L.
35'-312"
L.L. TO L.L.
RIVERCHASE GALLERIA
13. START TILE (FULL TILE) CENTERED ON ENTRY AS SHOWN
37'-43 8"
OVERALL LEASE LINE
SPACE #236A
2.0 TYPE: PREMIUM
TO
18
L.
'
L.
LL -11 1
LE 2 "
AS
E
LIN
E
AL
DI
GIT
11
.8
L
EQ
B
CAPACITY CALCULATIONS
RA
L. 2 '
L . -8 5
TO 8
"
L.
L.
O
VE
8"
16
'-2
7
L.
L.
SP
LAYOUT: A-103
TYPICAL TOILET ROOM FINISHES: FLOOR: VT-01, BASE: VB-01, WALLS: P-2,
DOORS: P-4, CEILING :EXISTING.
5.
9.
SCALE:
NOT USED.
4.
10. NEW DOOR MIRROR. REFER TO J4/A102 & J4/A-502 FOR ADDITIONAL INFORMATION
G1
PLOTTED: 7/9/2015 - 9:03 AM
TECH RACK & SECURITY SHELVES FOR EQUIPMENT/MUZAK ( IN BACK WRAP).
3.
8. (N) GRAB BAR
G
USER: PDICKERSON
NOT USED.
2.
A
NORTH
A1
SCALE:
FIXTURE ID
THEME
CT-HC
CT-1
CT-2
FS 1.0
GO 1.0
SP 10.0
SP 10.1
SP10.0 ST
SP 11.0
SP 11.1
STORY PANEL
FIXTURE QUANTITY
1
0
1
1
0
0
3
1
1
3
2
0
FIXTURE CAPACITY
0
0
0
0
52
104
80
40
80
80
40
-26
TOTAL
TOTAL FACINGS
0
0
0
0
0
0
240
40
80
240
80
0
680
2
AUTHORIZED FOR:
FINISH / FIXTURE PLAN
A-103
FINISH/FIXTURE PLAN
1
SGH STORE #: 4933
DRAWN BY: PWD
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GENERAL NOTES
1.
2.
REFER TO LIGHTING SPECIFICATIONS SCHEDULE FOR ADDITIONAL INFORMATION.
GRID LAYOUT FOR ACOUSTICAL CEILING TILE TO BE CENTRALLY LOCATED WITHIN
RETAIL SPACE AS INDICATED AT PLAN LAYOUT UNLESS SPECIFICALLY NOTED
OTHERWISE. REFER TO PLAN LAYOUT FOR EQUAL/EQUAL DIMENSIONS TO BE
MAINTAINED.
3. IT SHALL BE THE E.C.'S RESPONSIBILITY TO UNLOAD INVENTORY AND STORE
LIGHTING PACKAGE. THE E.C. SHALL ALSO SHIP ANY EXCESS MATERIALS BACK TO
THE ELECTRICAL PACKAGE DISTRIBUTOR.
4. E.C. SHALL RE-LAMP ALL FIXTURES PRIOR TO STORE OPENING BUT NOT DURING
HEAVY CONSTRUCTION PERIOD.
5. THE ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR AIMING TRACK HEADS PER SGH
STANDARDS. ELECTRICAL CONTRACTOR TO CONTACT LUXOTTICA PM FOR
FOCUSING DIRECTIVE IF NEEDED.
6. G.C. IS RESPONSIBLE TO PATCH/REPAIR ALL GYP.BD. CEILING SURFACES AFFECTED
BY DEMOLITION/NEW CONSTRUCTION.
7. EXISTING GYP.BD. CEILING SURFACES TO RECEIVE A FRESH COAT OF PAINT UPON
COMPLETION OF SCOPE OF CEILING WORK. LIGHTING INSTALLER IS RESPONSIBLE
TO TOUCH UP ANY AREAS DAMAGED BY THEIR WORK.
8. CENTER CEILING GRID & CEILING DEVICES U.N.O.
9. SPRINKLER HEADS SHOWN FOR REFERENCE ONLY. FIRE PROTECTION CONTRACTOR
TO DETERMINE ACTUAL AMOUNT AND LOCATION OF HEADS. SPRINKLER HEADS
SHOULD BE LOCATED SYMMETRICALLY IN THE CEILING AND SURFACE MOUNTED
WHEN APPLICABLE.
K
J
(E) GYP CEILING
Mason, Ohio 45040
SEAL
9'-0" A.F.F.
B.O. SALES CEILING
DISPLAY GRID (REFER TO
CEILING PLAN). HARDWARE
AND ANCHORS PROVIDED
WITH GRID. USE 6 HOOKS
PER 5' LONG SECTION OF
GRID.
EXISTING MALL BULKHEAD
EXISTING STOREFRONT
SYSTEM
8"
MIN
G
6.
TRACK LIGHT - REFER TO
ELECTRICAL SHEETS
7.
1'-4"
HOLD
GRAPHIC GRID OWNER PROVIDED. G.C. INSTALLED, COORDINATE TO MATCH CEILING
8.
NOT USED.
9.
NOT USED.
10. NOT USED.
11. RELOCATED LIGHT FIXTURE.
GRAPHICS GRID DETAIL
12. NOT USED.
13. LIGHT FIXTURE TRIM TO MATCH SOFFIT COLOR.
2'-07 8"
L.L. TO L.L.
35'-312"
L.L. TO L.L.
J
H
2'-63 8"
L.L. TO L.L.
(E) GYP(P-2)
10'-4" AFF
OVERALL LEASE LINE
14'-53 8"
11'-11" L.L. TO L.L.
17'-718"
A3W A3B
2'-0"
6
"
'-0
W
A3
W
A3
W
A3
(E)
13
L. 2 '
L . -8 5
TO 8
"
L.
L.
O
VE
16
'-2
7
A3B
L.
L.
TO
18
L.
'-1
L.
11
LE 2 "
AS
E
LIN
E
W
A3
A3W
(E)
A
NORTH
A1
2
X4
RECESSED ADJUSTABLE
DOWN LIGHT
C1B
RECESSED ADJUSTABLE
DOWN LIGHT (BLACK)
C4W
RECESSED ADJUSTABLE
DOWN LIGHT (WHITE)
C4B
RECESSED ADJUSTABLE
DOWN LIGHT (BLACK)
B1
2x2 LED RECESSED MOUNT
B2
2x4 LED RECESSED MOUNT
EXIT & EMERGENCY LIGHT
COMBINATION
EMERGENCY LIGHT
REMOTE POWER SUPPLY
ADJUSTABLE TRACK HEAD
(WHITE)
ADJUSTABLE TRACK HEAD
(BLACK)
C1W
EXIT SIGN
A
P
TC
(E)
(R)
3
4
5
6
7
8
9
10
11
TRAFFIC COUNTER
EXISTING
RELOCATION
SPACE #236A
2.0 TYPE: PREMIUM
S
C
SECURITY CAMERA
S
SPEAKER
SGH STORE #: 4933
S
SMOKE DETECTOR
DRAWN BY: PWD
AUTHORIZED FOR:
REFLECTED
CEILING PLAN
4'-1 LED STRIP SUSPENDED
B3 AT 13'-0" A.F.F.
CONCEALED SPRINKLER HEAD
12
RIVERCHASE GALLERIA
WIRELESS ACCESS POINT
A-104
UPRIGHT SPRINKLER HEAD
REFLECTED CEILING PLAN
1
LIGHT TRACK w/ LENGTH
(BLACK)
TB
(E) GYP (P-1)
9'-0" AFF
X3
LIGHT TRACK w/ LENGTH
TW
14
W
"
COL
LL
W
A3
'-0
RECEPTACLE DUPLEX
13
B
X2
EXHAUST FAN
6
)T
(N
"
.
5 8
.L
'-9 L L
3 1 RA L
VE
O
4
A3B
(E)
(E)
(E)
X1B EXIT LIGHT (BLACK)
SUPPLY DIFFUSER
2
4
ADJACENT
TENANT (N.I.C.)
A3B
A3
B
S
S
C
(E)
X1A EXIT LIGHT - CEILING MOUNTED
X1 EXIT LIGHT
RETURN AIR GRILLE
(R)
(E) (E)
(E)
FIXTURE EXTENTS BELOW
RA
W
A3
(E)
(R)
SYMBOLS LEGEND / GRAPHICAL KEY
8"
W
A3
11
G1
A-104
MALL COMMON
AREA (N.I.C.)
A
X1
W
A3
(E)
13
TB5'-0"
(E)
(E)
13
A3
B
100
"
SALES
6'
-0
W
A3
(E)
7
S
C
1
A3
B
W
A3
A3
W
(E) GYP(P-2)
12'-0" AFF
P
"
4'
-0
"
W
A3
A3
W
6
11
A
(E)
2
(R)
3
S
C
(E)
A3
W
(E) GYP(P-1)
10'-4" AFF
C
(E)
6
4
"
'-0
W
A3
102
(E)
(E)
(E) S
(E)
(E) GYP(P-1)
9'-0" AFF
1'-1"
(E)
(E)
(E) GYP(P-2)
10'-4" AFF
(E)
A3W A3W A3W
EQ(N) TW6'-0"
(E)
10
TOILET
ROOM
4
(E)
TW
W
A3
6
(E)
(E)
A3W A3W
TW
S (N)
S
C
D
(N) TW5'-0"
EQ
(E)
(E)
2
A3W A3W A3W A3W A3W
'-7
(E)
(E) GYP(P-2)
11'-4" AFF
A3W A3W A3W
(N) TW8'-0"
FE
(E)
(E)
ACT- EXISTING
11'-6" AFF
A3W A3W A3W
2
S
C
1'-11"
3'-6"
(E)
4'-0"
13
6
4'-0"
3'-107 8"
OVERALL L.L.
E
ADJACENT
TENANT (N.I.C.)
AT
5'-918"
12'-0"
ADJACENT
TENANT (N.I.C.)
LAYOUT: A-104
SECURITY CAMERAS.
UNDERSIDE OF SOFFIT
17'-63 8"
NOT USED.
FINISH, FIELD CUT TO THE DIM. AS SHOWN. CENTER IN DISPLAY WINDOW & MOUNT TO
F
PLOTTED: 7/9/2015 - 8:38 AM
LOCATION OF WIRELESS ACCESS POINT. REFER TO E-102.
LEASE LINE
37'-43 8"
USER: PDICKERSON
PREFERRED SPEAKER LOCATION. SPEAKER TO MATCH CEILING COLOR.
3.
5.
OVERALL LEASE LINE
SCALE:
LOCATION OF TRAFFIC COUNTER (SHOPPER TRAK). REFER TO E-102.
2.
4. (E) ACCESS PANELS.
G1
SCALE:
1.
RIVERCHASE GALLERIA
H
KEY NOTES
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GENERAL NOTES
P
P
2
K
B.O. CEILING
12'-0" AFF
B.O. CEILING
12'-0" AFF
B.O. CEILING
10'-4" AFF
B.O. CEILING
10'-4" AFF
T.O. STOREFRONT
9'-0" AFF
T.O. STOREFRONT
9'-0"
P
2
1.
REFER TO OWNER'S SIGNAGE STANDARD FOR ADDITIONAL SIGN INFORMATION.
SIGNAGE WORK TO BE SUBMITTED UNDER SEPARATE PERMIT.
2.
SEE SHEET A-103 FOR FINISH MATERIAL SCHEDULE
Mason, Ohio 45040
#
CUSTOM
FILLER PANEL
1
DIGITAL TOOL
P
2
SP 11.0
SP 11.5L
SP 11.8L
SP 11.5R
J
SP 11.0
SP 5.5 (36)
FINISH FLOOR
0'-0" AFF
SP 11.0
FINISH FLOOR
0'-0" AFF
SEAL
SP 11.4(18)
HPL06
H
H1
H6
SCALE:
ELEVATION
P
2
P
B.O. CEILING
12'-0" AFF
B.O. CEILING
12'-0" AFF
B.O. CEILING
10'-4" AFF
T.O. STOREFRONT
9'-0" AFF
B.O. CEILING
10'-4" AFF
2
P
1
P
2
B.O. CEILING
11'-4"
T.O. STOREFRONT
9'-0"
FINISH FLOOR
0'-0" AFF
FINISH FLOOR
0'-0" AFF
SP 10.5L
SP 10.0 ST
HPL06
P
1
SP 10.8R
SP10.5L
SP10.5R
F
STOREFRONT
CUSTOM
FILLER PANEL
SP 10.0
SP 10.4(18) SP 10.0
SP 10.5R SP 14.0-4
SP 10.5L
SP 10.0
AT
G
ELEVATION
HPL06
HPL06
E
E1
USER: PDICKERSON
E6
SCALE:
ELEVATION
ELEVATION
D
P
C
ON BOTH SIDES
OF DOOR & FRAME
P 3
P
1
1
SIGNAGE MATRIX
B.O. CEILING
12'-0" AFF
B.O. CEILING
10'-4" AFF
TYPE
ID
QTY.
REMARKS
BARRICADE
VINYL
1
BY BOSTON
BARRICADE
STOREFRONT
-
-
BY SIGN VENDOR
BLADE SIGN
SGH.BL-1
SGH.BL-2
1
BY SIGN VENDOR
CRASH GRAPHICS
SGH-CGL
2
BY SIGN VENDOR
B
PLOTTED: 7/9/2015 - 8:41 AM
LAYOUT: A-201
SCALE:
RIVERCHASE GALLERIA
SCALE:
SGH STORE #:4933
REVIEWED BY:RJH/JRM
HPL06
A
A1
A6
SCALE:
ELEVATION
1
SPACE #236A
2.0 TYPE: PREMIUM
DRAWN BY:PWD
FINISH FLOOR
0'-0" AFF
SCALE:
RIVERCHASE GALLERIA
2
3
4
5
BACKWRAP
SGH.BW
1
BY MILLWORKER
IDENTIFICATION SIGN
SGH.ID
-
BY MILLWORKER
VINYL DOT PATTERN
-
-
BY SIGN VENDOR
NOT USED
6
7
8
9
10
11
12
13
14
AUTHORIZED FOR:
ELEVATIONS
A-201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Mason, Ohio 45040
K
RELOCATE EXISTING
SIGN AFTER
RECLADDING IS
COMPLETE
MET-01
J
(N)BLADE SIGN
MET-01
SEAL
B.O. L.L. BULKHEAD
10'-10" A.F.F.
B.O. L.L. BULKHEAD
10'-10" A.F.F.
SIM.
H
B.O. SOFFIT
8'-10" A.F.F.
LEASE LINE
H11
LEASE LINE
5'-0"
EXISTING
STOREFRONT
GLAZING TO
REMAIN
F
LINE OF FIXTURES
BEYOND
T.O. STOREFRONT BASE
0'-6" A.F.F.
T.O. STOREFRONT BASE
0'-6" A.F.F.
FINISH FLOOR
0'-0" A.F.F.
FINISH FLOOR
0'-0" A.F.F.
TURN IN
STOREFRONT
LINE OF FIXTURES
BEYOND
E
(E) STOREFRONT
SYSTEM
TURN IN
STOREFRONT
(E) ENTRY
DOORS
TURN IN
STOREFRONT
E1
USER: PDICKERSON
PLOTTED: 7/9/2015 - 10:12 AM
LAYOUT: Model
SCALE:
TURN IN
STOREFRONT
STOREFRONT SIGNAGE
DRAWINGS TO BE SUBMITTED
UNDER SEPARATE COVER
AT
TURN IN
STOREFRONT
TURN IN
STOREFRONT
E8
SCALE:
STOREFRONT ELEVATION
STOREFRONT ELEVATION
RIVERCHASE GALLERIA
EXISTING
STOREFRONT
GLAZING TO
REMAIN
G
D
C
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
B
SGH STORE #: 4933
DRAWN BY: PWD
REVIEWED BY: RJH
AUTHORIZED FOR:
A
STOREFRONT PLAN
& ELEVATION
A1
SCALE:
A-401
NOT USED
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
4" W. X 18 GA CONTINUOUS SHEET METAL
BLOCKING WITH TOGGLE BOLTS. IF TOGGLE
BOLTS CANNOT BE USED, (EX: THE HAT
CHANNEL SITES IN THE WAY OF THE TRACK),
THEN FLAT HEAD SCREWS MATCHING SPIDER
TRACK ARE TO BE USED FOR FLUSH MOUNTING
REFER TO SECTIONS
FOR FRAMING
Mason, Ohio 45040
K
J
T
NO
1 1/2"
5/8" TYPE 'X' GYP.
BD. OVER 3 5/8"
METAL STUDS, TYP.
1/2" CORIAN ON
3/4" F.R.T.
PLYWOOD OVER
3 5/8" METAL
STUDS, TYP.
ED
US
HATCH INDICATES
EXISTING TENANT
CONSTRUCTION TO
REMAIN
B.O. BULKHEAD
REFER TO SECTIONS
F.R.T. BLOCKING
AS REQUIRED
T.O. ENTRY CEILING
REFER TO SECTIONS
METAL PANEL OVER 3/4"
PLYWOOD SHEATHING
INSTALLED BY G.C.
E11
A-501
9 3/4"
H
MET 01
MET 01
PLYWOOD SHEATHING
INSTALLED BY G.C.
SEAL
4"
BACKER ROD
& SEALANT
1'-8 1/2"
H1
SCALE:
EXISTING DOOR
SYSTEM
HEADER TO
REMAIN
HATCH INDICATES EXISTING
TENANT CONSTRUCTION TO
REMAIN
5"
BACKER ROD
& SEALANT
H8
SCALE:
STOREFRONT DETAIL
H11
SCALE:
STOREFRONT DETAIL
DOOR HEAD DETAIL
G
PLYWOOD SHEATHING
INSTALLED BY G.C.
HATCH INDICATES
EXISTING TENANT
CONSTRUCTION TO
REMAIN
F
BACKER ROD
& SEALANT
BACKER ROD
& SEALANT
AT
F.R.T. BLOCKING
AS REQUIRED
PLYWOOD SHEATHING
INSTALLED BY G.C.
E
MET 01
E8
E11
SCALE:
STOREFRONT DETAIL
STOREFRONT HEAD DETAIL
LAYOUT: A-501
SCALE:
RIVERCHASE GALLERIA
MET 01
EXISTING CONSTRUCTION
FINISHES, PATCH AND REPAIR
TO LIKE NEW CONDITION AS
REQUIRED.
USER: PDICKERSON
PLOTTED: 7/9/2015 - 10:14 AM
D
C
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
B
SGH STORE #: 4933
DRAWN BY: JLG
AUTHORIZED FOR:
A
STOREFRONT DETAILS
A1
E8
E11
SCALE:
SCALE:
SCALE:
NOT USED
1
2
3
4
5
6
7
NOT USED
8
9
10
11
A-501
NOT USED
12
13
14
3
4
5
6
J-CHANNEL
G.C. TO MECHANICALLY
FASTEN (EVERY 12"-18")
THE TOP, BOTTOM, AND
ONE SIDE J-CHANNEL,
SLIDE MIRROR IN (WITH
MIRROR MASTIC) AND
ATTACH THE OTHER SIDE
J-CHANNEL. GC TO USE
ANCHORS AS REQUIRED
TO SECURELY FASTEN.
K
7
8
10
11
12
13
1/8" THICK ZINC
TRANSITION STRIP
FURNISHED AND
INSTALLED BY TILE
CONTRACTOR.
FLASH PATCH
BY G.C.
BOBRICK B-1651836
MIRROR WITH
STAINLESS STEEL
CHANNEL FRAME
18"
ATTACH WALL HANGER TO
IN-WALL BLOCKING W/ #8
X 1 1/2" F/H MTL SCREWS
WHERE REQUIRED, TYP.
J4
J9
SCALE:
36"
THIN SET MORTAR BED
NOTE: PREPARE EXISTING CONCRETE
SLAB AS REQUIRED TO PROVIDE LEVEL
TRANSITION TO MALL FLOORING
DOOR MIRROR DETAIL
Mason, Ohio 45040
TILE FLOORING PER
PLANS & SCHEDULE
LINE OF EXISTING
CONCRETE SLAB
THIN SET MORTAR BED
NO
T
PROVIDE IN-WALL
BLOCKING AS REQUIRED
DOOR
J
1/8" THICK ZINC
TRANSITION STRIP
FURNISHED AND
INSTALLED BY TILE
CONTRACTOR.
TILE FLOORING PER
PLANS & SCHEDULE
LINE OF EXISTING
CONCRETE SLAB
14
D
SE
U
T
NO
36" MIN. TAPER
VINYL TILE
MIRROR BY G.C.
SCALE:
9
212"
2
US
ED
1
FLOOR TRANSITION
VCT TO PORCELAIN TILE
J12
SCALE:
FLOOR TRANSITION
TILE TO TILE
ED
US
SEAL
DOOR
T
NO
(E) MALL FLOORING.
FIELD VERIFY TYPE.
LINE OF EXISTING
CONCRETE SLAB
412"
G
G1
G4
SCALE:
G6
SCALE:
NOT USED
SCALE:
NOT USED
J6
SCALE:
RESTROOM MIRROR DETAIL
G12
SCALE:
FLOOR TRANSITION
CONCRETE TO VINYL
B.O. (E) ROOF DECK / STRUCTURE
OR (E) FLOOR DECK / STRUCTURE
F
ALL CAT 6 AND CAMERA
CABLING TO BE RAN INSIDE
WALL BEHIND TECH RACK
T
NO
24" W. x 18" D.
SHELVING RATED TO
100 LBS (TYP.) ON 60"
WHITE DOUBLE SLOTTED
STANDARDS
24" W 8" D SHELF
MONITOR,
KEYBOARD AND
MOUSE ON SHELF
5/8" GYPSUM BOARD
SEE WALL TYPE
FOR FRAMING
T
NO
FASTENING TO STRUCTURE
ABOVE TO COMPLY WITH
LANDLORD AND OR LOCAL
BUILDING DEPARTMENT
REQUIREMENTS.
ED
S
U
CONFORM TO BASIC
MINIMUM REQUIREMENTS
ESTABLISHED IN ASTM
C636
12 PORT PATCH
PANEL
10"
SAFE
2'-0"
1'-6"
TECH
RACK
D4
PHONE BOARD/SECURITY ELEVATION
SCALE:
T
NO
ED
S
U
17-19"
ED
S
U
CONCEALED
CONTINUOUS HINGE
T
NO
ED
S
U
SGH STORE #: 4933
2'-1114"
1'-05 8"
3
SIDE
3
4"
3
SCALE:
4
5
6
A11
SCALE:
PIPP SHELVING
7
8
9
10
AUTHORIZED FOR:
4"
ACCESS PANEL WITH
METAL DOOR. FINISH
TO MATCH CEILING.
SHELF SPACING AND BIN ARRANGEMENTS
CEILING MOUNTED ACCESS PANEL
METAL FLUSH MOUNTED
11
12
13
DRAWN BY: PWD
SCREWDRIVER
OPERATED LATCH.
VARIES
REFER TO CLG PLAN
1'-65 8"
1'-1114"
A7
DISABLED ACCESS SIGNAGE
RIVERCHASE GALLERIA
REFER TO CEILING PLAN
VARIES
5/8" GYP. BD.
FRONT
SCALE:
ATTACH WITH #8
SHEET METAL SCREWS.
SPACE #236A
2.0 TYPE: PREMIUM
3'-1114"
TYPICAL LAVATORY/SHELVING ELEVATION
2
T
NO
1'-6"
LAVATORY, REFER TO
PLUMBING DRAWINGS
A4
1
7'-1118"
RESTROOM
BRAILLE SIGN PER
1991 ADA REQ'TS
4'-8"
9"
29" MIN
27" MIN
34" MIN
RE ST ROOM
FRAMING AS
REQUIRED. REFER
TO SPECIFIC DETAILS
AND STRUCTURAL
DRAWINGS.
METAL TRIM
A1
SCALE:
ANSI APPROVED
E.S. PLASTIC
NEMA RATED
SELF
EXTINGUISHING
ADHESIVE
MOUNTED
40" MIN
60" MAX
8'-0"
40" MAX
INSULATE HOT WATER AND
DRAIN PIPING
SUSPENDED GYP. BD. CEILING DETAIL
INSTALLATION ON VERTICAL WALL TO BE
SIMILAR. ALL FASTENER REQUIREMENTS
AND SPECIFICATIONS ARE THE SAME.
NOTE: ALL SIGNAGE SHALL CONFORM WITH ADA ACCESSIBILITY
GUIDELINES, INCLUDING BUT NOT LIMITED TO PROPORTION, COLOR
CONTRAST AND RELIEF AND GRADE 2 BRAILLE REQUIREMENTS.
2'-0"
0.C.
A
D11
BRACKET
BLUE
B
FASTENING TO STRUCTURE ABOVE
TO COMPLY WITH LANDLORD AND
OR LOCAL BUILDING DEPARTMENT
REQUIREMENTS.
ALIGN
3'-0"
CL
5/8" GYP.
BD. 'TYPE X'
1/2" SHELF
VARIES
REFER TO PLAN
MIRROR, REFER TO
G6/A-502
1 1/2" CHANNEL
4'-0" O.C. MAX.
G.C. IS TO PROVIDE A
ONE-HOUR FIRE RATED CEILING
SYSTEM (WHEN-REQUIRED).
FOR ALL CEILING HEIGHTS.
SCALE:
ACOUSTICAL CEILING TILE
12" 12" 12" 12" 12" 12"
O.C. O.C. O.C. O.C. O.C. O.C.
C
D
SE
U
T
NO
20 GA. METAL STUD
WITH 1 5/8" FLANGE
AND 1/2" LIPS. (MIN.)
STANDARD STORES
(LOW SEISMIC)
IBC SEISMIC DESIGN CATEGORIES A,B&C
D7
SCALE:
3'-0" WIDE X 2" DEEP X 3/4" THICK
WHITE MELAMINE SHELVING, FINISHED
ON ALL SURFACES WITH WHITE
DOUBLE SLOTTED BRACKETS &
STANDARDS. FASTEN SHELVES TO
BRACKETS
REFER TO G4/A-102 FOR
TOILET ACCESSORY
MOUNTING HEIGHTS,TYP.
METAL FURRING
CHANNEL CLIP
INTERMEDIATE DUTY SUSPENDED
GRID SYSTEM CROSS "T" MEMBER
@ 2'-0" OR 4'-0" O.C. (REFER TO
SPECIFIC CEILING TYPE).
WALL MOLDING. SIZE TO MATCH
SIZE OF MAIN RUNNERS
HOLLOW METAL
JAMB / HEAD DETAIL
HANGER SPACING
4'-0" O.C. MAX.
24" O.C. MAX.
SPACING
WALL OR SOFFIT FRAMING AND
FINISHES. REFER TO SPECIFIC DETAILS.
D1
SCALE:
MINIMUM OF 3
TIGHT TURNS
AT ALL WIRES.
VARIES
HOLLOW METAL FRAME
24" W. X 48" H.
PHONE BOARD
12 GA VERTICAL SUPPORT
WIRE @ 4'-0" O.C. EA. WAY.
AND MAX. 8" FROM ALL EDGES.
SEE COMPRESSION STRUT
DETAIL FOR SEISMIC CONDITIONS
D, E & F. ON A-505
INTERMEDIATE DUTY
SUSPENDED GRID SYSTEM
MAIN RUNNER @ 2'-0" O.C.
ACOUSTICAL
CEILING TILES
DOUBLE QUAD
OUTLET
3"
3'-0"
4'-0"
D
33"-36"
LAYOUT: A-502
PLOTTED: 7/9/2015 - 10:19 AM
USER: PDICKERSON
DEDICATED QUAD
OUTLET
BEHIND TECH RACK
FRIDGE
12 GA VERTICAL
SUPPORT WIRE @
4'-0" O.C. EA. WAY.
AND MAX. 8" FROM
ALL EDGES.
MINIMUM OF 3 TIGHT
TURNS AT ALL WIRES.
DSL
MONITOR
MICRO
VARIES
A66 PHONE BLOCK
MICROWAVE AND
REFRIGERATOR
BY TENANT
T
NO
8" MAX.
AT PERIMETER
CLEAR SPACE FOR
ELECTRICAL PANEL
ANGLE BRACKET OR CLIP.
ATTACH PER MANUFACTURER
RECOMMENDATIONS.
ED
US
1 1/2"
MAX
E
ED
S
U
LINE OF EXISTING
CONCRETE SLAB
FLOOR TRANSITION
TILE TO MALL
VINYL TILE
AT
G.C. TO ADJUST SETTING
BED AS REQUIRED TO
ACHIEVE FLUSH TRANSITION
ALUMINUM THRESHOLD
PROVIDE LATEX LEVELING
COMPOUND AS REQUIRED TO
CREATE FLUSH CONDITION AT
THRESHOLD.
RIVERCHASE GALLERIA
TILE FLOORING PER
PLANS & SCHEDULE
37 8"
H
1/8" THICK ZINC
TRANSITION STRIP
FURNISHED AND
INSTALLED BY TILE
CONTRACTOR.
1 "
4
LOCKING DEVICES
AUTOMATICALLY SECURE
MIRROR TO CONCEALED WALL
HANGER WHEN IT IS LOWERED
INTO FINAL POSITION, TYP.
GENERAL
DETAILS
A-502
14
3
4
5
A.
1.
DRAWINGS AND SPECIFICATIONS ARE INTENDED TO BE COMPLIMENTARY. SPECIFIC INFORMATION
MAY BE FOUND IN EITHER OR BOTH.
2. THE TERM 'OWNER' AS STATED IN THE FOLLOWING SPECIFICATIONS AND CONSTRUCTION
DOCUMENTS, REFERS TO THE TENANT OF THIS SPACE ONLY AND DOES NOT REFER TO THE
LANDLORD OF THE PREMISES.
3. APPROVED VARIANCES TO THE PLANS AND SPECIFICATIONS ON ONE PROJECT SHALL NOT
CONSTITUTE AN APPROVAL OF LIKE VARIANCES ON SUBSEQUENT PROJECTS.
K
B.
C.
D.
E.
B.
1.
THE CONTRACTOR SHALL FURNISH FULL TIME CONTINUOUS SUPERVISION. THE PROJECT
SUPERINTENDENT SHALL REMAIN ON SITE THROUGH THE MERCHANDISE DATE OR THE
COMPLETION OF THE PUNCHLIST WHICHEVER IS LAST TO OCCUR.
2. SUSPENSION OF ALL CEILING AND OVERHEAD FRAMING IS TO BE FROM STRUCTURAL MALL
BEAMS AND TOP CHORD OF TRUSSES ONLY, NOT FROM MALL DECK.
3. GENERAL CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF IN-WALL BLOCKING FOR ALL
ITEMS IN STORE. REVIEW DRAWINGS THOROUGHLY.
4. ALL OWNER-FURNISHED MATERIALS ARE FURNISHED TAILGATE DELIVERY ONLY. THE CONTRACTOR
IS RESPONSIBLE TO UNLOAD, EXAMINE, AND TRANSPORT MATERIALS FROM THE POINT OF
OFF-LOAD TO THE JOBSITE OR STORAGE AREA AS APPLICABLE. MATERIALS WILL BE DELIVERED
TO THE CLOSEST AVAILABLE TRUCK DOCK OR OTHER LOCATION AS DIRECTED BY THE LANDLORD.
5. THE CONTRACTOR IS RESPONSIBLE FOR DAMAGE, LOSS, THEFT, OR DESTRUCTION OF ALL
OWNER-FURNISHED MATERIALS. THE CONTRACTOR WILL BE BACK-CHARGED THE FULL COST OF
REPLACEMENT MATERIALS INCLUDING FREIGHT CHARGES.
6. THE GENERAL CONTRACTOR SHALL EMPLOY SUBCONTRACTORS WHO ARE EXPERIENCED AND WHO
EMPLOY EXPERIENCED TRADESMEN.
7. THE GENERAL CONTRACTOR SHALL NOT EMPLOY NOISY CONSTRUCTION TECHNIQUES OR
EQUIPMENT DURING MALL OR STORE HOURS.
8. THE CONTRACTORS SHALL WORK IN COOPERATION AND HARMONY WITH THE LANDLORD AND THE
ADJACENT TENANTS IN SCHEDULING WORK IN ORDER TO CAUSE THE LEAST INCONVENIENCE TO
PERSONNEL AND PROPERTY. IF SECURITY IS REQUIRED WHILE WORKING IN ADJACENT TENANTS
SPACE, THIS COST WILL BE THE SOLE RESPONSIBILITY OF THE CONTRACTOR.
9. THE CONTRACTOR SHALL NOT UTILIZE GAS-OPERATED EQUIPMENT IN OCCUPIED SHOPPING
CENTERS. THE CONTRACTOR SHALL WORK IN HARMONY WITH THE LANDLORD'S REQUIREMENTS
RELATING TO NOISE ABATEMENT AND SAFETY.
10. THE CONTRACTOR SHALL FURNISH DUMPSTERS AS REQUIRED FOR THE EXCLUSIVE USE BY STORE
PERSONNEL DURING MERCHANDISING. THE CONTRACTOR SHALL INCLUDE IN THE BID A MINIMUM
OF ONE 40-YARD DUMPSTER OR THE EQUIVALENT. IF THE SALES AREA EXCEEDS 8,000 SQUARE
FEET, THE CONTRACTOR SHALL INCLUDE ONE ADDITIONAL DUMPSTER.
J
H
F.
C.
1.
EXERCISE PROPER PRECAUTION TO VERIFY ALL EXISTING CONDITIONS AND LAYOUT OF WORK.
CONTRACTOR TO NOTIFY OWNER'S CONSTRUCTION MANAGER OF ANY DISCREPANCIES
IMMEDIATELY. CONTRACTOR IS RESPONSIBLE FOR ANY ERROR RESULTING FROM FAILURE TO
EXERCISE SUCH PRECAUTION. SUCH ERROR WILL NOT BE CONSIDERED SUBSEQUENTLY AS A
BASIS FOR EXTRA COMPENSATION.
2. SHOULD A CONTRACTOR FIND DISCREPANCIES IN, OR OMISSIONS FROM THE DRAWINGS OR
SPECIFICATIONS, OR SHOULD HE BE IN DOUBT AS TO THEIR MEANING, HE SHALL AT ONCE
NOTIFY THE OWNER'S CONSTRUCTION MANAGER.
3. GENERAL CONTRACTOR IS RESPONSIBLE FOR SUPPLYING OR RENTING ALL TOOLS, WELDERS,
GENERATORS, ETC. FOR COMPLETING PROJECT.
G
D.
1.
ALL WORK, MATERIALS AND INSTALLATION SHALL BE IN STRICT ACCORDANCE WITH ALL
ORDINANCES, STATE AND LOCAL BUILDING CODES, LATEST EDITION, AND FOLLOW APPLICABLE
LANDLORD REQUIREMENTS.
2. DESIGN LOADS: LOADS AND CODE RESTRICTIONS FOR ALL DESIGN CONSIDERATIONS SHALL
CONFORM TO THE LOCAL AND STATE CODES, AND ALL GOVERNING CODES.
F.
E.
F
1.
THE AMERICAN INSTITUTE OF ARCHITECTS DOCUMENT A201 "GENERAL CONDITIONS OF THE
CONTRACTOR FOR CONSTRUCTION" IS A PART OF THE CONTRACT DOCUMENTS.
6
EQUATION TO DETERMINE VAPOR
EMISSION IN POUNDS:
1.
2.
E
3.
USER: PDICKERSON
PLOTTED: 7/9/2015 - 8:47 AM
LAYOUT: A-702
4.
5.
D
6.
C
7.
8.
9.
10.
11.
B
12.
TOTAL HOURS
POUNDS PER 1,000 SQUARE FEET IN 24 HOURS
THE VAPRECISION ANHYDROUS CALCIUM CHLORIDE TEST KIT, INSTRUCTIONS, CALCULATIONS AND ALL
OTHER PRINTED INFORMATION ARE PROPERTY OF VAPRECISION TESTING SYSTEMS, COPYRIGHT 1994.
REVISED AUGUST 1999. THE VAPRECISION ANHYDROUS CALCIUM CHLORIDE TEST KIT CONFORMS TO
THE AMERICAN SOCIETY FOR TESTING & MATERIALS DOCUMENTATION ASTM E-1907-97 AND
ASTM-F_1869-98 AND IS ACTUALLY PICTURED IN THE ASTM E-1907 SPECIFICATION. ASTM DOCUMENTS
ARE THE COPYRIGHT PROPERTY OF ASTM, AND CAN BE PURCHASED EASILY FROM THEIR WEB SITE AT
WWW.ASTM.ORG.
: THE FORMULA ABOVE COMPLIES TO ASTM DOCUMENTATION AS OF 8/99 AND DEDUCTS THE
AREA OF THE CALCIUM CHLORIDE DISH IN CONTACT WITH THE SLAB. THERE IS A DEBATE REGARDING
THIS ISSUE. TO CALCULATE THE TEST RESULT WITHOUT DEDUCTING THE AREA OF THE DISH, USE
108.846 INSTEAD OF 118.932.
A. THE CONTRACTOR SHALL ACCOMPLISH ANY MISCELLANEOUS MASONRY WORK INDICATED ON THE
PLANS, OR NOT INDICATED ON THE PLANS YET INCIDENTAL TO THE ACCOMPLISHMENT OF OTHER
WORK. WHERE APPLICABLE, MASONRY WORK SHALL MATCH EXISTING WORK. FINISH BRICK WORK
SHALL BE NEATLY TOOTHED INTO EXISTING MASONRY IF APPLICABLE.
A. STRUCTURAL STEEL: REFER TO STRUCTURAL DRAWINGS (WHERE APPLICABLE.)
B. METAL STUDS: COLD-FORMED GALVANIZED STEEL STUDS SIZED AS INDICATED ON DRAWINGS, WHICH
CONFORM TO ASTM C955 & C1007 . INCLUDE ALL ACCESSORIES, SUCH AS BRIDGING, TRACK, ETC.
PROVIDE ALL MISCELLANEOUS BOLTS, CLIPS, ANCHORS, ANGLES, BRACKETS, SLEEVES, FASTENERS, AND
OTHER METAL ITEMS AS REQUIRED. WOOD STUDS MAY BE SUBSTITUTED WHERE PERMISSIBLE BY CODES.
1. COLD FORMED STEEL FRAMING SHALL CONFORM TO REQUIREMENTS OF THE LATEST EDITION OF ANSI
"SPECIFICATION FOR DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS"
2. STUDS SHALL BE INSTALLED SO THE ENDS ARE POSITIONED AGAINST THE INSIDE OF THE RUNNER
TRACK WEB PRIOR TO FASTENING AND SHALL BE ATTACHED TO BOTH FLANGES OF THE UPPER AND
LOWER RUNNER TRACKS.
3. FOR VERTICAL STUDS WHERE THERE IS NO SHEATHING ATTACHED (SUCH AS ABOVE THE CEILING,) OR
WHERE SHEATHING IS ATTACHED TO ONLY ONE FACE, PROVIDE STANDARD BRIDGING AT 48" O.C. MAX.
ATTACH PER MANUFACTURER'S SPECIFICATIONS.
STEEL,
C. DECORATIVE METALS: INSTALL OWNER PROVIDED DECORATIVE METAL SUCH AS STAINLESS
PREFINISHED METAL, ETC. AS INDICATED ON DRAWINGS, PER MANUFACTURER'S RECOMMENDATIONS.
D. OWNER SUPPLIED METALS: G.C. IS RESPONSIBLE TO CONTACT VENDOR FOR ORDERING OF
PREFINISHED METAL STOREFRONT PANELS, CORNER GUARDS AT TILE FACED COLUMNS. REFER TO
INDIVIDUAL DETAILS FOR APPLICATION AND INSTRUCTIONS.
E. MISCELLANEOUS METALS: PROVIDE METAL SHAPES AND FABRICATIONS AS REQUIRED AND NOT INCLUDED
AS PART OF OTHER SECTIONS, WITH ANCHORS AND ACCESSORIES AS REQUIRED FOR COMPLETE
INSTALLATION. SUBMIT SHOP DRAWINGS FOR CUSTOM DATA, PRODUCT DATA FOR MANUFACTURED ITEMS
AND TEMPLATES FOR ANCHOR INSTALLATION BY OTHERS. STEEL SHAPES TO BE ASTM A36 STEEL.
A. PROVIDE NEW LUMBER, BEARING GRADE AND TRADEMARK OF ASSOCIATION UNDER WHICH IT WAS
PRODUCED.
B. LAYOUT, CUT, FIT AND ERECT FRAMING FOR ROUGH AND FINISHED WORK. INSTALL BLOCKING,
NAILERS, FURRING AND OTHER ROUGH AND FINISHED MATERIALS AS REQUIRED. BRACE, PLUMB
LEVEL MEMBERS IN TRUE ALIGNMENT AND RIGIDLY SECURE IN PLACE WITH SUFFICIENT NAILS, SCREWS
AND BOLTS AS NECESSARY.
C. USE FIRE RETARDANT LUMBER AND TRIM WHERE REQUIRED BY STATE OR LOCAL CODES, WHICH BEAR
THE MANUFACTURER'S STAMP OF AUTHENTICITY.
D. FURNISH AND INSTALL ALL GROUNDS OR BLOCKING REQUIRED TO RECEIVE STORE FIXTURES OR
OTHER WALL HUNG ELEMENTS, IF SHOWN ON DRAWINGS.
E. FURNISH AND INSTALL ALL ROUGH HARDWARE, ANCHORS, BOLTS, ETC., AS REQUIRED FOR
CARPENTRY WORK.
F. FINISH CARPENTRY: CONFORM TO ARCHITECTURAL WOODWORK INSTITUTE (AWI) QUALITY STANDARDS
OR WOODWORK INSTITUTE OF CALIFORNIA (WIC) "MANUAL OF MILLWORK" STANDARDS. PROVIDE
PRIMED WOOD WALL BASE - COPE ALL CORNERS, MITER ALL OUTSIDE CORNERS, COUNTER SINK AND
PUTTY ALL NAIL HOLES AND SAND SMOOTH.
13.
a.
OVERALL WIDTH (FACE OF GYPSUM BOARD ON DEMISING WALL TO FACE OF GYPSUM BOARD
ON DEMISING WALL).
OVERALL LENGTH (LEASE LINE TO INNER-FACE OF GYPSUM BOARD ON REAR WALL.)
ANY AND ALL COLUMN LOCATIONS - FREE STANDING OR PROJECTING.
AVAILABLE CLEAR HEIGHT FOR GRILLE AND CEILING AS DIMENSIONED ON DRAWINGS.
b.
c.
d.
A
A. THE CONTRACTOR IS RESPONSIBLE TO DETERMINE IF A NEW CONCRETE SLAB IS REQUIRED IN ALL OR
PART OF THE LEASED SPACE. SUCH FLOOR SLAB SHALL BE INSTALLED IN ACCORDANCE WITH ALL
REQUIREMENTS, LOCAL CODES, OR COMMON STANDARDS OF PRACTICE TO THE LOCALITY OF THE
PROJECT OR WHICHEVER IS STRICTER. IN THE ABSENCE OF THE ABOVE, THE CONTRACTOR SHALL
CONTACT THE OWNER FOR DIRECTION. MINIMUM REQUIREMENTS FOR THE FLOOR SLABS ON GRADE
1
2
3
4
5
9
10
11
12
6
7
13
14
(3)
E.
1.
F.
1.
EDGE SEALING: IMMEDIATELY AFTER CUTTING THE FINAL SIZES, AND APPLYING EDGE
TREATMENT; FACTORY SEAL EDGES OF MIRRORS WITH EDGE SEALER TO PREVENT
CHEMICAL OR ATMOSPHERIC PENETRATION OF GLASS COATING.
6. MISCELLANEOUS MATERIALS
a. SETTING BLOCK: NON-RUBBER OR NON-NEOPRENE BASED ELASTOMERIC MATERIAL
MANUFACTURED FOR SETTING SILVERED FLAT GLASS MIRRORS, COMPATIBLE WITH
ADHESIVE USED FOR PLACEMENT, WITH A TYPE A SHORE DUROMETER HARDNESS OF
85, PLUS OR MINUS 5. 1/8" WIDE X 1/4" HIGH X 4" LONG.
b. EDGE SEALER: COATING COMPATIBLE WITH GLASS COATING AND APPROVED BY MIRROR
MANUFACTURER FOR USE IN PROTECTING AGAINST SILVER DETERIORATION AT MIRROR
EDGES.
c. MIRROR MASTIC: PALMER PRODUCTS CORP., "MIRROR-MASTIC", (502) 893-3668,
(800) 431-6151, FAX (502) 895-9253.
d. DRYWALL AND PLYWOOD PAINT (POROUS SUBSTRATE PRIMER): PALMER PRODUCTS
CORP. "MIRROR-MASTIC BOND", (502) 893-3668, (800) 431-6151, FAX (502)
895-9253.
:
GENERAL CONTRACTOR TO CONTACT LANDLORD'S ON-SITE MANAGER FOR SPECIFICATIONS
ON ROOF PATCHING OR NAME OF ROOFING CONTRACTOR TO CONTACT FOR REPAIRS.
:
GENERAL CONTRACTOR TO PROVIDE AND INSTALL RIGID AND/OR FULL BATT INSULATION AND
4 MIL POLYETHELENE (VISQUEEN) VAPOR RETARDER AT WALLS AND CEILING AS REQUIRED BY
LANDLORD AND CONSTRUCTION DRAWINGS.
C.
1.
GENERAL: PROVIDE EXTERIOR AND INTERIOR JOINT SEALERS NOT PROVIDED ELSEWHERE;
TYPE SUITABLE FOR APPLICATION INDICATED WITH ACCESSORIES AS REQUIRED FOR
COMPLETE INSTALLATION.
2. INSTALLER QUALIFICATIONS: FIRM WITH MINIMUM FIVE YEAR'S SUCCESSFUL EXPERIENCE ON
PROJECTS OF SIMILAR TYPE AND SIZE, USING SPECIFIED PRODUCTS.
3. WARRANTY: REPAIR OR REPLACE JOINT SEALERS WHICH FAIL TO PERFORM AS INTENDED,
BECAUSE OF LEAKING, CRUMBLING, HARDENING, SHRINKAGE, BLEEDING, SAGGING,
STAINING OR LOSS OF ADHESION; WARRANTY PERIOD TWO YEARS.
4. EXTERIOR NON-TRAFFIC JOINTS: GE/SILPRUF, DOW/790-795 OR PECORA/854, LOW
MODULES SILICONE SEALANT.
5. TRAFFIC BEARING JOINTS: MAMECO/VULKEM 245 OR PECORA/NR-200 UREXPAN,
MULTI-COMPONENT POLYURETHANE, SELF-LEVELING JOINT SEALER.
6. MILDEW-RESISTANT SANITARY SEALANTS: GE/SANITARY SEALANT, DOW/BATHTUB CAULK, OR
PECORA/863 #345 WHITE; PROVIDE AT INTERIOR AREAS WHERE SEALANT WILL BE EXPOSED
TO WATER.
7. GENERAL INTERIOR JOINT SEALER: PECORA/AC-20 OR SONNEBORN/SONOLAC, ACRYLIC OR
LATEX EMULSION. MISCELLANEOUS MATERIALS: PRIMERS, SEALERS, JOINT CLEANERS, BOND
BREAKER TAPE
8. AND SEALANT BACKER RODS AS RECOMMENDED BY SEALANT MANUFACTURER FOR
APPLICATIONS INDICATED.
a. OVERSIZE BACKER ROD MINIMUM 30 % TO 50 %%% OF JOINT OPENING.
9. COLORS: AS INDICATED OR SELECTED BY OWNER'S PROJECT MANAGER FROM
MANUFACTURER'S FULL RANGE OF COLORS.
10. PREPARATION: CLEAN JOINT SURFACES IMMEDIATELY BEFORE INSTALLATION OF JOINT
SEALER AND PRIME OR SEAL JOINT SURFACES AS RECOMMENDED BY MANUFACTURER.
11. INSTALLATION: COMPLY WITH MANUFACTURER'S PRINTED INSTALLATION INSTRUCTIONS AND
ASTM C1193.
b. EMPLOY INSTALLATION TECHNIQUES WHICH WILL ENSURE JOINT SEALERS ARE
DEPOSITED IN UNIFORM, CONTINUOUS RIBBONS WITHOUT GAPS OR AIR POCKETS,
WITH COMPLETE "WETTING" OF BOND SURFACES.
e.
D.
1.
2.
NEW CONSTRUCTION - GENERAL CONTRACTOR TO FURNISH AND INSTALL 48" WIDE
REFLECTIVE BUBBLE INSULATION MADE WITH TWO LAYER REFLECTIVE METALIZED ALUMINUM
SEPARATED BY A 5/16" ENCLOSED AIR SPACE. INSTALL PER MANUFACTURERS
SPECIFICATIONS.
EXISTING CONSTRUCTION - GENERAL CONTRACTOR TO FURNISH AND INSTALL 24" WIDE .024
WHITE ALUMINUM TRIM COIL. INSTALL PER MANUFACTURERS SPECIFICATIONS.
E.
7.
WEATHER BARRIER MEMBRANE (DUPONT TYVEK COMMERCIALWRAP)
MANUFACTURER: DUPONT; 4417 LANCASTER PIKE, CHESTNUT RUN PLAZA 728, WILMINGTON, DE
19805; 1-800-44-TYVEK (8-9835);
INSTALLATION SHALL BE IN ACCORDANCE WITH WEATHER BARRIER MANUFACTURER'S
INSTALLATION GUIDELINES AND RECOMMENDATIONS. SECURE USING WEATHER BARRIER
MANUFACTURER RECOMMENDED FASTENERS, SPACE 12-18 INCHES VERTICALLY ON CENTER
ALONG STUD LINE, AND 24 INCHES ON CENTER, MAXIMUM HORIZONTALLY.
8.
:
1. DOOR HARDWARE: REFER TO DOOR SCHEDULE FOR HARDWARE SPECIFICATIONS.
2. HOLLOW METAL FRAMES: K.D. MINIMUM 16 GAUGE. SIZE AND SHAPE PER DOOR SCHEDULE.
3. LABELED DOORS: WHERE REQUIRED, PROVIDE U.L. LABEL DOORS AND FRAMES PER
APPLICABLE STATE AND LOCAL BUILDING CODES. LABEL DOORS TO RECEIVE DOOR CLOSER.
4. FABRICATE AND ERECT TRUE, PLUMB AND SQUARE AS SPECIFIED AND AS DETAILED AND PER
MANUFACTURER'S RECOMMENDATIONS.
B.
:
1. GLASS
a. STOREFRONT GLASS TO BE HORIZONTALLY TEMPERED. SIZE AND NUMBER OF PIECES
AS SHOWN ON DRAWINGS. GLAZING CONTRACTOR TO PROVIDE AND INSTALL ALL
GLAZING CHANNELS, GASKETS, BLOCKING, ETC., REQUIRED FOR COMPLETE
INSTALLATION. PROVIDE NEAT, UNIFORM (1/4" WIDE UNLESS NOTED OTHERWISE) GAPS
BETWEEN GLASS PANES AND BETWEEN PANES AND ADJACENT VERTICAL SURFACES.
b. ARRISSED EDGE: EDGES TO BE DIAMOND GROUND 1/16" 45 DEGREE BEVEL AT FRONT
AND BACK FACES WITH ALL EXPOSED EDGES UNIFORMLY MACHINE POLISHED.
c. OWNER REQUIRES THAT STOREFRONT GLASS NOT BOW MORE THAN +/- 1/16" OUT OF
VERTICAL.
d. ALL GLASS TO BE SET IN GLAZING GASKETS THE SIZE AND SHAPE NECESSARY TO
ACCOMPLISH GOOD WORKMANSHIP. CAULKING NOT PERMITTED.
C.
:
1. QUALITY ASSURANCE
a. INSTALLER QUALIFICATIONS: AN EXPERIENCED INSTALLER WHO HAS COMPLETED MIRROR
GLAZING SIMILAR IN MATERIAL, DESIGN, AND EXTENT TO THAT INDICATED; WHOSE WORK
HAS RESULTED IN MIRROR INSTALLATIONS WITH A RECORD OF NOT LESS THAN 5 YEARS
OF SUCCESSFUL IN-SERVICE PERFORMANCE.
b. SOURCE LIMITATIONS FOR MIRRORS: OBTAIN MIRRORS FROM ONE
SUPPLIER/MANUFACTURER FOR EACH TYPE OF MIRROR INDICATED.
c. SOURCE LIMITATIONS FOR GLAZING ACCESSORIES: OBTAIN GLAZING ACCESSORIES
FROM ONE SOURCE FOR EACH TYPE OF ACCESSORY INDICATED.
d. GLAZING PUBLICATIONS: COMPLY WITH THE APPLICABLE RECOMMENDATIONS OF THE
FOLLOWING. WHERE RECOMMENDATIONS CONFLICT THE MORE STRINGENT SHALL APPLY.
e. GLASS ASSOCIATION OF NORTH AMERICA (GANA): "GLAZING MANUAL" AND THE MIRROR
DIVISION'S "MIRRORS, HANDLE WITH EXTREME CARE: TIPS FOR THE PROFESSIONAL ON
THE CARE AND HANDLING OF MIRRORS."
f. NATIONAL GLASS ASSOCIATION (NGA): "CUSTOM MIRRORS, FABRICATION AND
INSTALLATION.
2. DELIVERY, STORAGE, AND HANDLING.
a. PROTECT MIRRORS ACCORDING TO MIRROR MANUFACTURER'S WRITTEN INSTRUCTIONS
AND AS NEEDED TO PREVENT DAMAGE TO MIRRORS FROM CONDENSATION,
TEMPERATURE CHANGES DIRECT EXPOSURE TO SUN, OR OTHER CAUSES.
b. COMPLY WITH MIRROR MANUFACTURER'S WRITTEN INSTRUCTIONS FOR SHIPPING,
STORING, AND HANDLING MIRRORS AS NEEDED TO PREVENT DETERIORATION OF
SILVERING, DAMAGE TO EDGES, AND ABRASION OF GLASS SURFACES AND APPLIED
COATINGS. STORE INDOORS, PROTECTED FROM MOISTURE INCLUDING CONDENSATION.
3. PROJECTION CONDITIONS: ENVIRONMENTAL LIMITATIONS - DO NOT INSTALL MIRRORED
GLASS UNTIL AMBIENT TEMPERATURE AND HUMIDITY CONDITIONS ARE MAINTAINED AT
LEVELS INDICATED FOR FINAL OCCUPANCY.
4. SILVERED FLAT GLASS MIRROR MATERIAL: 6.0 MM THICK AND COMPLYING WITH ASTM C
1503, MIRROR SELECT QUALITY FOR USE IN VISUALLY DEMANDING APPLICATIONS
REQUIRING MINIMAL DISTORTIONS AND BLEMISHES.
5. FABRICATION
a. CUTOUTS: FABRICATE CUTOUTS FOR NOTCHES AND HOLES IN MIRRORS WITHOUT
MARRING VISIBLE SURFACES. LOCATE AND SIZE CUTOUTS SO THEY FIT CLOSELY
AROUND PENETRATIONS IN MIRRORS.
b. MIRROR EDGE TREATMENT: CUTTING AND POLISHING
(1) TYPICAL MIRRORS: FLAT EDGES WHERE THE CLEAN CUT "SQUARE" EDGE OF THE
GLASS IS FLAT AND SURFACES EDGES ARE SLIGHTLY ARRISSED. AFTER GRINDING
THE ARISSES, EDGES SHALL BE POLISHED TO A HIGH GLOSS SURFACE WHERE THE
SURFACE REFLECTIVITY IS SIMILAR IN APPEARANCE TO THE MAJOR SURFACE OF
THE GLASS.
(2) BEVELED EDGED MIRRORS: PROVIDE BEVELED EDGED MIRRORS WHERE THE
SURFACE EDGE OF THE GLASS IS BEVELED TO WIDTH INDICATED ON THE OWNER
FURNISHED DRAWINGS. THE ANGLE FORMED BY THE INTERSECTION OF THE PLANCE
OF THE BEVEL WITH THE MAJOR SURFACE FACE OF THE GLASS SHALL BE BETWEEN
3 TO 10 DEGREES. THE BEVELED SURFACE AND THE NOSE OF THE BEVEL SHALL BE
POLISHED TO A HIGH GLOSS SURFACE WHERE THE SURFACE REFLECTIVITY IS
SIMILAR IN APPEARANCE TO THE MAJOR SURFACE OF THE GLASS.
8
9
10
TOP AND BOTTOM ALUMINUM J CHANNELS: ALUMINUM EXTRUSIONS WITH A RETURN
DEEP ENOUGH TO PRODUCE A GLAZING CHANNEL TO ACCOMMODATE 6 MM THICK
MIRRORS AND HEAVY BODIED MIRROR MASTIC SPECIFIED AND IN A SINGLE PIECE. THE
ENDS OF THE BACK LIPS OF ALL CHANNELS SHALL BE FACTORY SNIPPED AND FILED SO
THAT THEY WILL NOT BE SEEN AFTER INSTALLATION.
(1) BOTTOM AND SIDE TRIM: C.R. LAURENCE CO. INC., 1/4" STANDARD "J" CHANNEL
(CATALOG NUMBER D636P POLISHED FINISH), (800) 421-6144, FAX (800)
262-3299. J-CHANNELS FORMED WITH FRONT LEG AND BACK LEG NOT LESS THAN
3/8" AND 7/8" IN HEIGHT, RESPECTIVELY.
D.
1.
2.
4.
5.
TOP TRIM: C.R. LAURENCE CO. INC., 1/4" DEEP NOSE "J" CHANNEL (CATALOG
NUMBER D645P POLISHED FINISH), (800) 421-6144, FAX (800) 262-3299.
J-CHANNELS FORMED WITH FRONT LEG AND BACK LEG NOT LESS THAN 5/8" AND
1-3/16" IN HEIGHT, RESPECTIVELY.
f. STUD FASTENERS: PROVIDE #6 GAGE DIAMETER, 1-5/8" LONG, PHILLIPS BUGLE HEAD,
SELF-DRILLING TYPE, FINE THREADED STEEL SCREW FASTENERS IN QUANTITY AS
REQUIRED FOR SUPPORT AND FASTENING OF WOOD TRIMS AND MIRRORS CHANNELS
TO DRYWALL STUD FRAMING AND SHEET METAL BACKER PLATES. HILTI KWI-PRO SELF
DRILL DRYWALL SCREWS, ORDERING NAME: 6" X 1'-5/8" PBH SD, ITEM #: 00086216;
HILTI CORPORATION (800) 879-8000.
g. PLASTIC WOOD FILLER: COMMERCIAL QUALITY WOOD FILLER SPECIFICALLY
MANUFACTURED TO ADVANCE THE FINAL BUILD AND SMOOTHNESS OF THE INSTALLED
WOOD TRIM SURFACE BY FILLING DENTS, SCRATCHES, MITER JOINTS, AND VOIDS
ABOVE COUNTERSUNK FASTENER HEADS. THE SELECTED FILLER SHALL BE EITHER
NEUTRAL OR TINTED TO MATCH THE COLOR OF THE WOOD TRIM.
h. PLYWOOD FASTENERS: PROVIDE MINIMUM #6 GAGE DIAMETER, PHILLIPS FLAT HEAD,
SHARP POINTED, COARSE THREADED, STEEL WOOD SCREW FASTENERS IN QUANTITY AS
REQUIRED. FURNISH PLYWOOD FASTENERS IN LENGTH AS REQUIRED TO SPAN THROUGH
WOOD MIRROR TRIM, AND MIRROR CHANNELS, PLUS 3/4"
i.
WOOD MIRROR TRIM
EXAMINATION
a. EXAMINE SUBSTRATES, OVER WHICH MIRRORS ARE TO BE MOUNTED, WITH INSTALLER
PRESENT, FOR COMPLIANCE WITH INSTALLATION TOLERANCES, SUBSTRATE
PREPARATION, AND OTHER CONDITIONS AFFECTING PERFORMANCE.
(1) VERIFY COMPATIBILITY AND SUITABILITY OF SUBSTRATES, INCLUDING
COMPATIBILITY OF MIRROR MASTIC WITH EXISTING FINISHES OR PRIMERS.
PROCEED WITH MIRRORED GLASS INSTALLATION ONLY AFTER UNSATISFACTORY
CONDITIONS HAVE BEEN CORRECTED AND SURFACES ARE DRY.
PREPARATION
a. COMPLY WITH MASTIC MANUFACTURER'S WRITTEN INSTALLATION INSTRUCTIONS FOR
PREPARATION OF SUBSTRATES.
(1) MIRROR, DRYWALL AND PLYWOOD SUBSTRATES SHALL BE FREE OF DUST, BE
CLEAN, AND DRY PRIOR TO APPLICATION OF MIRROR MASTIC AND DRYWALL AND
PLYWOOD PAINT. IF PLYWOOD OR DRYWALL SURFACES HAVE BEEN PAINTED PRIOR
TO APPLICATION OF THE SPECIFIED DRYWALL AND PLYWOOD PAINT THE EXISTING
PAINT SHALL BE SANDED THROUGH THE ORIGINAL SURFACE AND THE SUBSTRATE
CLEANED PRIOR TO THE APPLICATION OF DRYWALL AND PLYWOOD PAINT.
:
GENERAL: INSTALL MIRRORS WITH MIRROR GLAZING CHANNELS TO COMPLY WITH WRITTEN
INSTRUCTION OF MIRROR AND MIRROR GLAZING CHANNEL MANUFACTURERS, WITH
REFERENCED GANA AND NGA PUBLICATIONS, OWNER FURNISHED DRAWINGS, AND AS
SPECIFIED. MOUNT MIRRORS PLUMB, IN LINE AND IN A MANNER THAT AVOIDS DISTORTING
REFLECTED IMAGES
MIRROR CHANNEL INSTALLATION:
a. TO PLYWOOD: DRILL, DO NOT DIMPLE, BACK LIP OF CHANNEL TO RECEIVE FASTENERS
WITH HOLES PROPERLY SIZED AND SPACED TO RECEIVE FASTENERS. ATTACH MIRROR
CHANNELS BY SCREW ATTACHING MIRROR CHANNEL THROUGH THE BACK LIP OF THE
CHANNEL TO PLYWOOD SUBSTRATE IN ACCORDANCE WITH THE FASTENER
MANUFACTURERS WRITTEN INSTRUCTIONS. INSTALL THE WEB OF THE TOP CHANNEL 1/4"
HIGHER THAN THE HEIGHT OF THE MIRROR TO ALLOW THE RAISING OF THE MIRROR IN
TO THE TOP CHANNEL AND ITS SUBSEQUENT LOWERING INTO THE BOTTOM CHANNEL.
AFTER INSTALLING FASTENERS PLACE MASKING TAPE OVER THE ENTIRE LENGTH OF THE
BACK LIP OF THE CHANNEL COMPLETELY COVERING THE FASTENER HEADS TO PROTECT
THE MIRROR FROM BEING CHIPPED IN SETTING. ADHERE SETTING BLOCKS AT QUARTER
POINTS FOR BOTTOM MIRROR CHANNELS USING ONLY 2 SETTING BLOCKS PER MIRROR
PANEL.
b. TO DRYWALL: MARK THE LOCATIONS FOR THE STUD FASTENERS ON THE BACK LIP OF
EACH MIRROR CHANNEL AT EQUAL INTERVALS NOT OVER 8" ON CENTER, AND NOT
MORE THAN 3" FROM ENDS PRIOR TO DRILLING THE CHANNEL. DRILL AND COUNTERSINK,
DO NOT DIMPLE BACK LIP OF CHANNEL TO RECEIVE STUD FASTENERS AT MARKED
LOCATIONS WITH HOLES PROPERLY SIZED TO RECEIVE STUD FASTENERS. ATTACH
MIRROR CHANNELS BY SCREW ATTACHING MIRROR CHANNEL THROUGH THE BACK LIP
OF THE CHANNEL THROUGH DRYWALL, STUD FRAMING AND SHEET METAL BACKER PLATE
SUBSTRATES IN ACCORDANCE WITH THE FASTENERS MANUFACTURERS WRITTEN
INSTRUCTIONS.
(1) INSTALL THE WEB OF THE TOP CHANNEL 1/4" HIGHER THAN THE HEIGHT OF THE
MIRROR TO ALLOW THE RAISING OF THE MIRROR INTO THE TOP CHANNEL AND ITS
SUBSEQUENT LOWERING ONTO THE WEB OF THE BOTTOM CHANNEL. AFTER
INSTALLING FASTENERS PLACE MASKING TAPE OVER THE ENTIRE LENGTH OF THE
BACK LIP OF THE CHANNEL COMPLETELY COVERING THE FASTENER HEADS TO
PROTECT THE MIRROR FROM BEING CHIPPED IN SETTING. ADHERE SETTING BLOCKS
TO THE WEB OF THE BOTTOM MIRROR CHANNELS, LOCATED AT QUARTER POINTS,
USING 2 SETTING BLOCKS PER MIRROR PANEL.
WOOD TRIM & INSTALLATION
a. BEFORE INSTALLING MIRROR WOOD TRIM, EXAMINE SHOP-FABRICATED WORK FOR
COMPLETION AND COMPLETE WORK AS REQUIRED. PRIME TO ALL EXPOSED SURFACES
OF THE MIRROR WOOD TRIM WHICH WILL BE IN CONTACT WITH THE MIRROR BACKING
TO ELIMINATE INTERACTIONS BETWEEN THE RESINS IN THE WOOD AND THE MIRROR
BACKING.
b. INSTALL MIRROR WOOD TRIM PLUMB, LEVEL, TRUE AND STRAIGHT WITH NO
DISTORTIONS. SCRIBE AND CUT MIRROR WOOD TRIM TO FIT ADJOINING WORK, AND
REFINSH CUT SURFACES AND REPAIR DAMAGED FINISH AT CUTS. INSTALL WITH
MINIMUM NUMBER OF JOINTS POSSIBLE, USING FULL-LENGTH PIECES (FROM MAXIMUM
LENGTH OF WOOD TRIM AVAILABLE) TO GREATEST EXTENT POSSIBLE. DO NOT USE
PIECES LESS THAN 16" LONG, EXCEPT WHERE SHORTER SINGLE-LENGTH PIECES ARE
NECESSARY. SCARF RUNNING JOINTS. MITERS OVER 4" LONG SHALL BE SPLINED AND
GLUED.
PROTECTION AND CLEANING
a. PROTECT MIRRORS FROM BREAKAGE AND CONTAMINATING SUBSTANCES
RESULTING FROM CONSTRUCTION OPERATIONS. USING CLEAN WARM WATER,
CLEAN MIRRORS BY METHODS RECOMMENDED IN REFERENCED GLAZING
STANDARDS.
Mason, Ohio 45040
SEAL
(2)
A.
4.5 X 118.932 = 8.3
64.5
POUNDS PER 1,000 SQUARE FEET IN 24 HOURS
WEIGHT GAIN X 118.932 =
WITHIN FIVE (5) DAYS OF COMMENCEMENT OF CONSTRUCTION, OR WITHIN TWO (2) DAYS
FOLLOWING COMPLETION OF DEMOLITION, THE CONTRACTOR SHALL CAREFULLY EXAMINE THE
SITE AND REPORT TO THE OWNER'S CONSTRUCTION MANAGER ANY DISCREPANCIES IN THE
LEASE-HOLD DIMENSIONS OR CONFLICTS BETWEEN THE PHYSICAL SPACE AND THE INTENT OF
THE WORKING DRAWINGS (G.C. TO PAY SPECIAL ATTENTION TO POP-UP CEILING AREAS, CEILING
HEIGHTS, AND AVAILABLE HEIGHT FOR ROLL-UP ENTRANCE GRILLES).
GENERAL CONTRACTOR IS TO CONTACT LANDLORD'S ON-SITE MANAGER PRIOR TO ANY
DEMOLITION WORK TO DETERMINE THE AVAILABILITY OF DUMPSTER PLACEMENT, NOISE AND
DUST ABATEMENT REQUIREMENTS, ETC.
GENERAL CONTRACTOR IS TO ARRANGE WITH THE LANDLORD A CONVENIENT TIME TO PERFORM
DEMOLITION WORK AND INSTALL TEMPORARY PROTECTED MEANS OF EGRESS FROM REQUIRED
EXITS, INCLUDING TEMPORARY LIGHTING AND SAFETY DEVICES, ALL IN ACCORDANCE WITH
GOVERNING STATE AND LOCAL CODE AND LANDLORD REQUIREMENTS.
GENERAL CONTRACTOR TO ERECT BARRICADE AT STOREFRONT PER LANDLORD'S
SPECIFICATIONS. GENERAL CONTRACTOR TO INSTALL OWNER SUPPLIED BARRICADE SIGN (IF
PROVIDED) AS SHOWN ON INSTRUCTIONS SENT WITH BID PACKAGES.
THE GENERAL CONTRACTOR SHALL REMOVE, REPAIR, RESTORE AND REPLACE WHERE NECESSARY
OR INDICATED ON THE DRAWINGS OR AS REQUIRED. CUT ALL NECESSARY OPENINGS FOR ANY
REQUIRED PURPOSE AND REPAIR, WHERE NECESSARY, AFTER CUTTING. INSOFAR AS POSSIBLE,
ALL PROTRUSIONS, MARKS, CRACKS OR OTHER EVIDENCE OF A DEFICIENT OR DAMAGED
CONDITION SHALL BE ELIMINATED UNLESS SPECIFICALLY NOTED OTHERWISE. ANY PARTS WHICH
ARE SPLIT, CRACKED, CHIPPED, SPALLED, BROKEN, MISSING, OR OUT OF LINE OR ADJUSTMENT,
MECHANICALLY OR STRUCTURALLY UNSAFE OR UNSOUND, BENT, TORN, OR OTHERWISE
DEFICIENT OR INJURED IN ANY MANNER, SHALL BE REMOVED, REPLACED, RESTORED, OR
SATISFACTORILY REPAIRED AS DIRECTED BY THE OWNER'S CONSTRUCTION MANAGER.
GENERAL CONTRACTOR IS RESPONSIBLE FOR THE REMOVAL AND DISPOSAL OF ALL LEASE-HOLD
IMPROVEMENTS INCLUDING, BUT NOT LIMITED TO: INTERIOR WALLS, CEILINGS, FLOOR
COVERINGS (ALL ADHESIVES), PLATFORMS, STORE-FRONTS, ETC. (UNLESS INDICATED
OTHERWISE ON ARCHITECTURAL DRAWINGS). ALL EXISTING UNUSED MECHANICAL, ELECTRICAL
AND/OR PLUMBING FIXTURES AND EQUIPMENT, INCLUDING ABANDONED ROOFTOP HVAC
EQUIPMENT AND CURBS (UNLESS INDICATED OTHERWISE ON MECHANICAL AND ELECTRICAL
DRAWINGS) AND/OR SKYLIGHTS ARE TO BE REMOVED AND THE ROOF PATCHED PER ITEM #12
BELOW: CAPPING IS
PERMITTED!
GENERAL CONTRACTOR IS RESPONSIBLE FOR THE REMOVAL AND DISPOSAL OF ALL LOOSE ITEMS
SUCH AS, BUT NOT LIMITED TO: TRADE FIXTURES, MISCELLANEOUS DECORATIONS, KITCHEN
EQUIPMENT, ETC.
ALL ABANDONED ELECTRICAL/TELEPHONE CONDUIT, PLUMBING LINES AND MECHANICAL
DUCTWORK MUST BE REMOVED TO THE POINT OF ORIGIN.
INFORM THE LANDLORD'S ON-SITE MANAGER OF ANY UTILITY NEEDING TO BE DISCONNECTED OR
CAPPED, PRIOR TO DOING SO.
GENERAL CONTRACTOR IS TO EXERCISE EXTREME CARE DURING DEMOLITION SO AS NOT TO
DAMAGE OR DISRUPT UTILITIES OR SPRINKLER LINES WHICH MIGHT PASS THROUGH THIS SPACE
TO SERVICE OTHER MALL SPACES OR OTHER TENANTS (G.C. WILL BEAR SOLE RESPONSIBILITY
FOR ANY SUCH DAMAGE OR DISRUPTION).
GENERAL CONTRACTOR IS RESPONSIBLE FOR ALL DEMOLITION WORK AND MUST INFORM
OWNER'S CONSTRUCTION MANAGER OF THE EXTENT OF SUCH WORK, PRIOR TO BIDDING.
GENERAL CONTRACTOR IS TO DETERMINE HIS RESPONSIBILITY FOR THE FLOOR SLAB AND
DEMISING WALL INSTALLATION OR MODIFICATIONS WITH LANDLORD AND OWNER'S
CONSTRUCTION MANAGER TO MEET ALL TENANT IMPROVEMENT CRITERIA AND RESPONSIBILITY
SET BY THE LANDLORD OR OWNER. GENERAL CONTRACTOR IS TO VERIFY THE ACTUAL
CONDITION OF THE PERIMETER DEMISING WALLS AND/OR FLOOR SLAB PRIOR TO BIDDING. BID
IS TO INCLUDE ALL WORK REQUIRED.
8
NUMERIC EXAMPLE W/ A 4.5 GAIN IN 64.5 HRS.
(ALWAYS ROUND TO THE NEAREST TENTH):
WEIGHT GAIN X 118.932 = POUNDS
TOTAL HOURS
A.
7
SHALL BE FOUR INCH THICK CONCRETE SLAB REINFORCED WITH 6"x 6"W.W.F.; CONCRETE TO BE
3,500 PSI OR HIGHER PLACED OVER COMPACTED SAND AGGREGATE BASE. PLACE 10 MIL VAPOR
BARRIER AT THE MIDPOINT OF THE COMPACTED SAND/AGGREGATE BASE. THE SOIL SHALL BE INSECT
TREATED IF CUSTOMARY TO THE LOCALITY OR AS REQUIRED BY LANDLORD.
PROVIDE JOINT SEALANT IN ALL CONCRETE CONTROL JOINTS AS SPECIFIED IN DIVISION 7.
PROVIDE JOINT FILLER STRIPS WHERE APPLICABLE: ASTM D-1751, CELLULOSE FIBER.
VAPOR RETARDER, CLEAR 10 MIL POLYETHELENE SHEET.
SLAB FINISHES
1. FLOAT FINISH FOR INTERIOR STEPS, RAMPS AND SURFACES TO RECEIVE WATER PROOFING OR
OTHER DIRECT-APPLIED MATERIAL
2. TROWELED FINISH FOR FLOOR SURFACES AND FLOORS TO RECEIVE FLOOR COVERINGS, PAINT
OR OTHER THIN FILM FINISH COATINGS.
3. TROWEL AND FINE BROOM FINISH FOR SURFACES TO RECEIVE THINSET TILE.
4. NON-SLIP BROOM FINISH FOR EXTERIOR CONCRETE PLATFORMS, STEPS AND RAMPS.
ANHYDROUS CALCIUM CHLORIDE CONCRETE MOISTURE VAPOR EMISSION TEST KIT CONDUCTING THE
MOISTURE TEST
1.
: BEFORE YOU TEST, MAKE SURE YOU HAVE BASIC TOOLS FOR
CLEANING THE SLAB, INCLUDING A SCRAPER AND WIRE BRUSH. MAKE SURE YOU HAVE A
QUALITY GRAM SCALE AND A PROPER SUPPLY OF TEST KITS AND PROTECTIVE CONES. ENSURE
BUILDING CLIMATE IS BETWEEN 65 & 85 DEGREES FAHRENHEIT WITH RELATIVE HUMIDITY %
BETWEEN 40-60 FOR AT LEAST 48 HOURS PRIOR TO, AND DURING TESTING.
2.
: THE SLAB MUST BE CLEAN OF DEBRIS AND ADHESIVE RESIDUE.
SHOT BLAST SURFACE OR WIRE BRUSH SLAB CLEAN. REMOVE DUST THOROUGHLY. DO NOT
USE CHEMICALS OF ANY KIND TO CLEAN THE FLOOR. AVOID TEST LOCATIONS NEAR CRACKS OR
JOINTS, OR IN DIRECT SUNLIGHT. PREPARE 3 TEST SITES FOR THE FIRST 1,000 SQ. FT. AND
INCLUDE 1 MORE TEST FOR EACH ADDITIONAL 1,000 SQUARE FEET OF AREA.
3.
: READ THE WARNING LABEL ON PACKAGE AND THEN OPEN THE
CONTAINER BAG. SET THE ENTIRE TAPE SEALED DISH ON THE GRAM SCALE AND RECORD ITS
WEIGHT ON THE DISH LID AND ON THE TEST KIT BOOKLET. RECORD THE STARTING DATE AND
TIME AS WELL. ENSURE THAT THE SAME SCALE WILL BE AVAILABLE FOR RE-WEIGHING THE DISH,
OR THE VALIDITY OF THIS TEST WILL BE COMPROMISED.
4.
: REMOVE THE BLUE VINYL TAPE FROM THE DISH. BE CAREFUL NOT
TO LOSE THE TAPE AS YOU WILL NEED TO RESEAL THE DISH LATER. STORE THE DISH LID
CAREFULLY AND STICK THE TAPE ALONG THE SIDE OF THE PLASTIC. DOME TO KEEP IT SAFE.
SOME PEOPLE PREFER TO TAPE THE DISH'S LID TO THE INSIDE OF THE DOME WHERE IT CAN BE
READ THROUGH THE TOP. DO NOT TOUCH OR SPILL THE CALCIUM CHLORIDE.
5.
: PLACE THE OPEN DISH ON THE SLAB MAKING SURE THE CALCIUM CHLORIDE
INSIDE IS FAIRLY LEVEL. DO NOT SET THE KIT DIRECTLY OVER A CONTROL JOINT OR CRACK.
REMOVE THE WHITE PAPER ON THE DOME, AND CENTER THE DOME OVER THE DISH. THE ONLY
MOISTURE ABSORBED BY THE CALCIUM CHLORIDE MUST BE WITHIN THE 70 SQUARE INCH AREA
OF THE DOME THAT IS IN CONTACT WITH THE CONCRETE SLAB.
6.
: USING THE HANDLE OF YOUR WIRE BRUSH OR OTHER TOOL, FIRMLY
SQUASH THE GASKET UNDER THE FLANGES OF THE DOME. THE IDEAL INSTALLATION WILL SEAT
THE OUTER FLANGE OF THE DOME TO THE SLAB. THEN THE GASKET MATERIAL WILL MOVE TO
LINE UP WITH THE INSIDE EDGE OF THE DOME. PLACE YOUR HAND OVER THE DOME AND GENTLY
APPLY PRESSURE. THERE SHOULD BE NO LEAKS IN THE GASKET.
7.
: PLACE THE OPTIONAL SAFETY CONE OVER THE DOME AND LET THE
TEST REMAIN UNDISTURBED FOR 60 TO 72 HOURS. MOST MANUFACTURERS OF FLOORING
PRODUCTS RECOMMEND AT LEAST ONE KIT PER 1,000 SQUARE FEET. THE TEST ONLY
MEASURES A SMALL AREA OF SLAB SURFACE AND MOISTURE LEVELS CAN VARY GREATLY OVER
1,000 SQ. FT. TEST SEVERAL AREAS WHENEVER POSSIBLE.
8.
: AFTER 60 TO 72 HOURS, CUT OPEN THE DOME AND
CAREFULLY RETRIEVE THE DISH. REPLACE THE LID AND SEAL IT BACK UP WITH THE BLUE TAPE.
WEIGH THE DISH AGAIN ON THE SAME GRAM SCALE. RECORD THE ENDING WEIGHT, DATE, AND
TIME ON THE DISH LID AS WELL AS ON THE TEST KIT BOOKLET. FOLLOW THE INSTRUCTIONS IN
THIS BOOKLET TO COMPUTE THE MOISTURE VAPOR EMISSION RATE.
CALCULATING RESULTS: USE THE FOLLOWING EQUATION TO DETERMINE THE VAPOR EMISSION
VOLUME IN POUNDS PER 1,000 SQUARE FEET IN 24 HOURS. SEE FOOTNOTE.
AT
2
RIVERCHASE GALLERIA
1
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
DRAWN BY: PWD
AUTHORIZED FOR:
ARCHITECTURAL
SPECIFICATIONS
A-701
11
12
13
14
1.
K
2.
3.
4.
5.
6.
7.
8.
9.
J
10.
11.
H
12.
13.
G
3
4
:
GENERAL: INSTALL OWNER SUPPLIED EXTRUDED ALUMINUM STOREFRONT AND ENTRANCE
SYSTEM WITH DOORS, FRAMES, HARDWARE, AND ACCESSORIES AS REQUIRED FOR COMPLETE
WEATHERTIGHT INSTALLATION.
STANDARDS: COMPLY WITH ARCHITECTURAL ALUMINUM MANUFACTURERS
ASSOCIATION (AAMA) "ALUMINUM STORE FRONT AND ENTRANCE MANUAL."
CODES AND REGULATIONS: COMPLY WITH APPLICABLE CODES AND REGULATIONS.
SUBMITTALS: NOT REQUIRED.
INSTALLATION WARRANTY
MANUFACTURER: OLD CASTLE OR EQUAL , AS APPROVED BY OWNER.
STOREFRONT: EXTRUDED ALUMINUM ENTRANCE SYSTEM AS INDICATED ON DRAWINGS.
a. ALUMINUM TYPE: AS RECOMMENDED BY MANUFACTURER FOR APPLICATION INDICATED,
BUT NOT LESS THAN EXTRUDED ALUMINUM, ASTM B221, 6061 OR 6063 ALLOY AND T5
OR T6 TEMPER.
FINISH: SEE DRAWINGS
GLAZING: ASTM C1048, PROVIDE FULLY TEMPERED SELECT GLAZING QUALITY CLEAR FLOAT
GLASS; NOMINAL 1/2" SAFETY GLASS UNLESS OTHERWISE INDICATED.
a. APPLIED GLAZING FILM: SUPPLY & APPLY 3M FILM ON ALUMINUM FRAMED STOREFRONT
GLASS WHERE INDICATED ON DRAWINGS.
GLAZING ACCESSORIES: OF TYPE RECOMMENDED BY MANUFACTURER TO SUIT SECURITY
LOCATIONS AND APPLICATIONS FOR DRY GLAZING INSTALLATION.
MISCELLANEOUS MATERIALS:
a. STEEL REINFORCEMENT AND BRACKETS: MANUFACTURER'S STANDARD WITH MINIMUM 2
OZ. HOT-DIP ZINC COATING, ASTM A123, APPLIED AFTER FABRICATION.
b. BITUMINOUS PAINT: COLD-APPLIED MASTIC, SSPC PAINT 12, COMPOUNDED FOR 30 MIL
THICKNESS PER COAT.
c. FLASHING: INSTALL SUB-SILL FLASHING MEMBERS; MINIMUM 22 GAGE SHEET ALUMINUM
OF SIZES AND SHAPES INDICATED AND AS REQUIRED TO DRAIN WATER TO EXTERIOR;
MATCH ADJACENT ALUMINUM MEMBER FINISH.
d. ANCHORING DEVICES: CORROSION RESISTANT TYPE CAPABLE OF SUPPORTING ENTRANCE
SYSTEM AND SUPERIMPOSED DESIGN LOADS; DESIGN TO ALLOW ADJUSTMENTS OF
SYSTEM PRIOR TO BEING PERMANENTLY FASTENED IN PLACE.
FABRICATION:
a. ACCURATELY FIT TOGETHER JOINTS AND CORNERS; MATCH COMPONENTS ENSURING
CONTINUITY OF LINE AND DESIGN; ENSURE JOINTS AND CONNECTIONS ARE FLUSH, 1/64th
INCH MAX. AND WEATHERPROOF. NO CAULK AT ANY JOINTS OR CONNECTIONS. NO
EXCEPTIONS!
b. SEPARATE DISSIMILAR MATERIALS WITH BITUMINOUS PAINT OR PREFORMED SEPARATORS
WHICH WILL PREVENT CORROSION.
INSTALLATION: INSTALL ALUMINUM FRAMED STOREFRONT ASSEMBLIES, INCLUDING ENTRANCES,
IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS AND TO MEET DESIGN
REQUIREMENTS INDICATED, FOR WEATHERTIGHT INSTALLATION.
a. ENSURE ASSEMBLIES ARE PLUMB, LEVEL AND FREE OF WARP OR TWIST; MAINTAIN
DIMENSIONAL TOLERANCES AND ALIGNMENT WITH ADJACENT WORK.
b. USE SUFFICIENT ANCHORAGE DEVICES TO SECURELY AND RIGIDLY FASTEN ASSEMBLIES
TO BUILDING.
c. INSTALL HARDWARE IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS, USING
PROPER TEMPLATES. COORDINATE INSTALLATION OF CYLINDERS WITH SECTION 08700.
d. INSTALL SILL MEMBERS AND THRESHOLDS IN BED OF COMPOUND, JOINT FILLERS OR
GASKETS TO PROVIDE WEATHERTIGHT CONSTRUCTION.
e. GLASS INSTALLATION: COMPLY WITH GANA GLAZING MANUAL AND GLAZING
MANUFACTURER INSTRUCTIONS. DO NOT ALLOW GLASS TO TOUCH METAL SURFACES.
E.
1.
2.
LAYOUT: A-702
PLOTTED: 7/9/2015 - 8:47 AM
USER: PDICKERSON
:
FURNISH AND INSTALL ALL GYPSUM DRYWALL AND SYSTEMS COMPLETE WITH PARTITION
FRAMING, CEILING SUSPENSION SYSTEMS AND RELATED ACCESSORIES, PARTS, MATERIALS,
ETC. AS SHOWN ON DRAWINGS AND AS SPECIFIED. INSTALL ALL MATERIALS PER
MANUFACTURER'S SPECIFICATIONS AND RECOMMENDATIONS.
2. GYPSUM DRYWALL: U.S. GYPSUM 5/8" THICK FIRE CODE SHEETROCK (TYPE 'X') PANELS OF
STANDARD QUALITY. GENERAL CONTRACTOR MAY USE NON-RATED 5/8" THICK BOARD IN
AREAS OF STORE WHERE ALLOWED BY STATE AND LOCAL CODES. ALWAYS USE TYPE 'X' ON
DEMISING WALLS.
3. FASTENERS: DRYWALL SCREWS OF PROPER SIZE AND TYPE, PER MANUFACTURER'S
RECOMMENDATIONS.
4. METAL ACCESSORIES: U.S. GYPSUM OR GOLD BOND SYSTEM OF COMPONENTS AND JOINT
TAPE.
5. JOINT TREATMENT: U.S. GYPSUM OR GOLD BOND SYSTEM OF COMPONENTS AND JOINT TAPE.
6. METAL FRAMING: WHERE NOT SHOWN AND SPECIFIED TO BE COLD-FORMED METAL FRAMING IN
THE DRAWINGS, CONFORM TO ASTM C645 AND ASTM C754.
7. FINISHING: COMPLY WITH GYPSUM ASSOCIATION (GA) "LEVELS OF GYPSUM BOARD FINISH" - GA
LEVEL 4, THREE COAT FINISHING AND SANDING IS REQUIRED FOR SURFACES INDICATED TO BE
PAINTED, PROVIDE FLUSH, SMOOTH JOINTS AND SURFACES READY FOR APPLIED PAINT
FINISHES.
B.
1.
C
B
:
CERAMIC TILE AS SPECIFIED IN FINISH SCHEDULE AND RESPONSIBILITY SCHEDULE. (IF
APPLICABLE)
INSTALL CERAMIC TILE USING RECOMMENDED METHODS OF THE TILE CONTRACTORS
ASSOCIATION OF AMERICA AND THE TILE COUNCIL OF AMERICA, INC.
3. INSTALL CERAMIC TILE USING GROUT AND JOINT SPACING SPECIFIED IN FINISH SCHEDULE.
4. ADHESIVE IS TO BE PROVIDED AND INSTALLED BY GENERAL CONTRACTOR (PER
MANUFACTURER'S SPECIFICATIONS).
5. CAREFULLY CLEAN ALL WORK AND REPLACE OR REPOINT ANY DAMAGED WORK AND LEAVE IN
PERFECT CONDITION. USE NO ACID, AGENT OR DEVICE THAT WILL MAR SURFACE. CONSULT
WITH OWNER'S CONSTRUCTION MANAGER FOR INSTRUCTIONS (DO NOT POLISH CERAMIC TILE).
6. CERAMIC TILES ARE TO BE SET WITHOUT TRIPPING HAZARD TO CUSTOMERS OR STAFF.
7. THE GENERAL CONTRACTOR IS RESPONSIBLE TO CORRECT RAISED CERAMIC TILES FOR THE
ENTIRE DURATION OF THE WARRANTY PERIOD AT THE DIRECTION OF THE OWNER'S
CONSTRUCTION MANAGER.
2.
C.
:
1. FURNISH AND INSTALL CEILING SYSTEM COMPLETE WITH SUSPENSION SYSTEM AND RELATED
ACCESSORIES AS SHOWN ON DRAWINGS AND AS SPECIFIED.
2. SUSPENSION SYSTEMS SHALL BE ADEQUATE TO SUPPORT LIGHT FIXTURES, CEILING, GRILLES,
DIFFUSERS AND OTHER NORMAL ACCESSORIES. PROVIDE SYSTEM COMPONENTS FROM A
SINGLE MANUFACTURER.
3. INSTALL CEILING AND SUSPENSION SYSTEMS IN STRICT ACCORDANCE WITH ASTM C754, ASTM
C635 AND ASTM C636. FINISH CEILING SHALL BE LEVEL, WITH JOINTS SNUG AND SQUARE,
AND TILES OR PANELS IN PERFECT CONDITION.
4. MATERIALS AND FINISHES a. REFER TO DRAWINGS FOR LOCATION OF SPECIFIED MATERIALS
AND FINISHES WHEN APPLICABLE.
b. NON-SALES CEILING: AS SCHEDULED OR EQUAL. CLASS "A" RATING.
c. WHEN A ONE-HOUR FIRE-RATED CEILING ASSEMBLY IS REQUIRED BY LANDLORD, STATE
OR LOCAL CODES, THEN GENERAL CONTRACTOR IS TO CONFORM WITH UNDERWRITER'S
LABORATORIES DESIGN FOR A ONE-HOUR RATED ASSEMBLY AS SCHEDULED.
d. G.C. TO PROVIDE ONE BOX OF THE SPECIFIED CEILING TILES ON SITE FOR FUTURE USE.
5. SEISMIC ZONES: PROVIDE TO COMPLY WITH STATE AND LOCAL REQUIREMENTS FOR SEISMIC
BRACING OF CEILING SUSPENSION SYSTEM, WITH ASTM E580 AND AS DETAILED ON
DRAWINGS. COMPLY ALSO WITH AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE 7-02) AND
CEILING AND INTERIOR SYSTEMS CONSTRUCTION ASSOCIATION (CISCA) STANDARDS. CONSULT
LOCAL CODES FOR MINIMUM CEILING AREA REQUIREMENTS.
D.
1.
A
2.
:
GENERAL: G.C. TO INSTALL OWNER SUPPLIED VINYL FLOORING SYSTEM WITH ACCESSORIES AS
REQUIRED FOR COMPLETE FINISHED INSTALLATION.
PROJECT CONDITIONS: PRIOR TO INSTALLATION OF ANY FLOORING, GC MUST ENSURE THAT
THE JOBSITE AND SUB-FLOOR MEET THE REQUIREMENTS OF THE FOLLOWING INSTRUCTION.
a. G.C. TO PERFORM MOISTURE TEST ON ALL CONCRETE FLOORS AS DIRECTED BY NWFA
AND INSTALL BOSTIK MVP4 VAPOR BARRIER. MOISTURE CONTENT OF WOOD SUB-FLOOR
MUST NOT EXCEED 12% AND CONCRETE MOISTURE CONTENT MUST NOT EXCEED 3LBS.
b.
G.C. TO PROVIDE MOISTURE TEST REPORT TO CONSTRUCTION MANAGER
1
2
3
7
:
SEE FINISH SCHEDULE. BUTT BASE TO FLOOR AND WALL WITH NO GAPS.
FILL ALL CRACKS, JOINTS, ETC. IN SUB-FLOOR WITH CRACK FILLER APPROVED BY FLOORING
MANUFACTURER. INSTALL ALL MATERIALS WITH WATERPROOF TYPE ADHESIVES AS
RECOMMENDED BY FLOORING MANUFACTURER FOR MATERIALS AND SURFACES INVOLVED.
THIS SPECIFICATION DEFINES THE REQUIREMENTS FOR SURFACE PREPARATION,
COATING SYSTEMS, MINIMUM AND MAXIMUM DRY FILM THICKNESS, SPECIAL
APPLICATION INSTRUCTIONS WHEN NECESSARY AND INSPECTION FOR PAINTING OF
SPECIFIED SUBSTRATES.
2. IF INSTRUCTIONS CONTAINED IN THIS SPECIFICATION, BID DOCUMENTS OR THE
PAINTING SCHEDULE ARE AT VARIANCE WITH THE PAINT MANUFACTURER'S
INSTRUCTIONS OR THE APPLICABLE STANDARDS AND CODES PUBLISHED BY
SSPC OF OSHA, SURFACES SHALL BE PREPARED AND PAINT APPLIED TO MEET
THE HIGHER STANDARD, AS DETERMINED BY THE DESIGN AUTHORITY.
3. THE CONTRACTOR SHALL BE RESPONSIBLE FOR REQUESTING PROMPT
CLARIFICATION WHEN INSTRUCTIONS ARE LACKING, CONFLICTS OCCUR IN THE
SPECIFICATION AND/OR PAINT MANUFACTURER'S LITERATURE, OR THE
PROCEDURE SPECIFIED IS NOT CLEARLY UNDERSTOOD. IN THE EVENT, THE
CONTRACTOR FAILS TO RESOLVE THE CONFLICTS, WHICH MAY EXIST, HE SHALL
BE RESPONSIBLE FOR HANDLING THE DISCREPANCIES IN A MANNER AS
PRESCRIBED BY THE DESIGN AUTHORITY AT NO ADDITIONAL COST TO THE
OWNER.
4. ALL PERTINENT SAFETY REGULATIONS, BOTH THE OWNER'S AND
OSHA'S SHALL BE ADHERED TO RIGIDLY. IN ADDITION, ALL SAFETY
PRECAUTIONS NOTED ON THE MANUFACTURER'S PRODUCT DATA
SHEETS AND LABELS SHALL BE OBSERVED FOR BOTH MATERIALS
AND EQUIPMENT.
5. THE APPLICATION SHALL LEAVE NO SAGS, RUNS OR HOLIDAYS. ANY
DAMAGE IN ANY COAT SHALL BE REPAIRED TO CONFORM TO THIS
SPECIFICATION PRIOR TO FINAL INSPECTION.
6. WHERE REQUIRED, IMPERFECTIONS AND HOLES IN SURFACES TO BE
COATED SHALL BE CLEANED AND REPAIRED ACCORDING TO HIGHEST
INDUSTRY STANDARDS AND IN A MANNER APPROVED BY THE DESIGN AUTHORITY.
7. ALL MATERIALS SPECIFIED FROM BENJAMIN MOORE & CO., AND ARE
INTENDED TO ESTABLISH STANDARDS OF QUALITY AND GENERIC TYPES. COATING SUBSTITUTIONS
ARE PROHIBITED.
8. ALL COATING MATERIALS SHALL BE DELIVERED TO OTHER JOB SITE IN
THE ORIGINAL AND UNOPENED CONTAINERS, PLAINLY MARKED WITH
THE PROPER DESIGNATION OF THE PRODUCT, AS WELL AS THE
NAME OF THE MANUFACTURER. ALL COATING MATERIALS AT THE
JOB SITE SHALL BE SUBJECT TO INSPECTION BY THE OWNER'S REP.
9. ALL PAINTING MATERIALS SHALL BE STORED IN A CLEAN, DRY WELL VENTILATED PLACE,
PROTECTED FROM SPARKS, FLAME, DIRECT RAYS OF THE SUN, AND EXCESSIVE HEAT OR COLD.
THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR THE PROTECTION AND SAFETY OF THE
MATERIALS STORED BY G.C. AT THE JOB SITE.
10. PAINT ADDITIVES ARE PROHIBITED.
11. COLORS FOR INDIVIDUAL ITEMS SHALL BE AS SPECIFIED IN THE
FINISH PAINTING SCHEDULE, OF THIS SPECIFICATION AND/OR THE
PAINTING SCHEDULE SUBMITTED AS A PART OF THE SCOPE OF
WORK DOCUMENTS WITH THE SCOPE OF WORK SCHEDULE TAKING
PRECEDENCE. COLORS SHALL NOT BE SUBSTITUTED.
12. SURFACES NOT TO BE PAINTED SHALL BE PROTECTED DURING CLEANING & PAINTING
OPERATIONS.
13. BEFORE ANY SURFACE IS COATED, IT SHALL BE CLEANED CAREFULLY OF
ALL DUST, DIRT, GREASE, LOOSE RUST, MILL SCALE, OLD PAINT, ETC.
14. ALL CLEANED METAL SHALL BE PRIME COATED , AS SPECIFIED,
IMMEDIATELY AFTER CLEANING TO PREVENT NEW RUSTING OR
OXIDATION OF CLEANED SURFACES.
15. SURFACES
15.1 SURFACE PREPARATION (ALL METAL AND WOOD SURFACES)
a. SOLVENT CLEANING SSPC-SP1 - THIS IS A METHOD FOR REMOVING OIL, GREASE,
DRAWING AND CUTTING FLUIDS FROM THE SURFACE. A COMPLETE DESCRIPTION OF THE
PROCEDURES CAN BE FOUND IN STEEL STRUCTURES PANTING COUNCIL SPECIFICATION
"SSPC-SP-1 SOLVENT CLEANING"
b. EMULSIFIER SOLVENT CLEANING - ALL AREAS TO BE PAINTED SHOULD BE CLEANED
THOROUGHLY WITH A SOLUTION OF OIL AND GREASE EMULSIFIER. THIS CLEANER
EMULSIFIES ALL OF THE OILY SUBSTANCE CONVERTING IT TO SOAP AND FLOATS IF OUT
OF THE SURFACE. THOROUGHLY SCRUB ALL AREAS UNTIL SURFACE APPEARS CLEAN, AND
THE RINSE WELL WITH CLEAN WATER. THIS PROCESS SHOULD BE REPEATED TO ENSURE
THAT THERE ARE NO OTHER OILY CONTAMINANTS REMAINING.
15.2 WALLS AND COLUMNS - EGGSHELL FINISH
a. PRIMER: APPLY ONE (1) COAT OF SUPER SPEC LATEX ENAMEL UNDERCOATER & PRIMER
SEALER (PRODUCT # 253) AT A WET FILM THICKNESS OF 3.6 MILS PER COAT TO ACHIEVE
A DRY FILM THICKNESS OF 1.1 MILS PER COAT. (TINT PRIMER ONE SHADE LIGHTER THAN
FINISH COAT).
b. FINISH: APPLY TWO (2) COATS OF REGAL SELECT PREMIUM INTERIOR PAINT EGGSHELL
FINISH (549) AT A WET FILM THICKNESS OF 3.8 MILS PER COAT TO ACHIEVE A DRY FILM
THICKNESS OF 1.5 MILS PER COAT.
c. APPLICATION: BRUSH SMALL AREAS AND AROUND TRIM AND CEILING WITH PREMIUM
QUALITY NYLON/POLYESTER BRUSH. FIRST COAT MAY BE SPRAYED, BUT BACKROLL WITH
SOFT WOVEN COVER NO LARGER THAN ½” NAP TO MINIMIZE TEXTURE. SECOND COAT
SHALL BE APPLIED BY ROLLER ONLY.
15.3 CEILINGS AND SOFFITS - FLAT FINISH
FINISH COAT).
b. FINISH: APPLY TWO (2) COATS OF REGAL SELECT PREMIUM INTERIOR PAINT FLAT FINISH
(547) AT A WET FILM THICKNESS OF 3.8 MILS PER COAT TO ACHIEVE A DRY FILM
c. APPLICATION: BRUSH SMALL AREAS AND AROUND TRIM AND CEILING WITH PREMIUM
QUALITY NYLON/POLYESTER BRUSH. FIRST COAT MAY BE SPRAYED, BUT BACKROLL WITH
SOFT WOVEN COVER NO LARGER THAN ½” NAP TO MINIMIZE TEXTURE. SECOND COAT
SHALL BE APPLIED BY ROLLER ONLY.
15.4 WALL BASE, CASING, AND TRIM - SEMI GLOSS FINISH
A.
1.
D
6
F.
1.
F
E
5
IMMEDIATELY AFTER DEMOLITION AND/OR 1 WEEK PRIOR TO FLOOR INSTALLATION. IF THE
G.C. FAILS TO PROVIDE REPORT, ANY FLOOR FAILURE ATTRIBUTED TO MOISTURE, IT WILL
BE THE RESPONSIBILITY OF THE G.C. TO REPLACE (LABOR AND MATERIAL).
c. ALL WORK INVOLVING WATER OR MOISTURE SHOULD BE COMPLETED BEFORE FLOOR
INSTALLATION.
d. ROOM TEMPERATURE AND HUMIDITY OF INSTALLATION AREA SHOULD BE CONSISTENT
WITH NORMAL, YEAR-ROUND LIVING CONDITIONS FOR AT LEAST A WEEK BEFORE
INSTALLATION. ROOM TEMPERATURE OF 60 TO 70 DEGREE F AND HUMIDITY RANGE OF
40 TO 60% IS RECOMMENDED.
e. G.C. TO STORE FLOORING AT INSTALLATION SITE FOR 72 HOURS BEFORE INSTALLATION
TO ALLOW FLOORING TO ADJUST TO ROOM TEMPERATURE AND HUMIDITY. DO NOT
STORE DIRECTLY ON CONCRETE OR NEAR OUTSIDE WALLS. THIS FLOORING MAY NOT BE
ACCEPTABLE FOR FULL BATHROOM INSTALLATIONS BECAUSE OF MOISTURE ASSOCIATED
WITH SUCH LOCATIONS.
f. COMMENCEMENT OF WORK IS ACCEPTANCE OF CONDITIONS.
3. MANUFACTURERS: REFER TO FINISH SCHEDULE.
4. ADHESIVE: AS RECOMMENDED BY MANUFACTURER TO ENSURE MAXIMUM DURABILITY OVER
TIME; NONTOXIC, WATERPROOF TYPE SUITABLE FOR FLOORING, SUBSTRATE, AND ACCEPTABLE
TO APPLICABLE AUTHORITIES.
5. MOISTURE VAPOR PROTECTION: BOSTIK MVP4 MOISTURE BARRIER OR AS RECOMMENDED BY
MANUFACTURER; ONE-PART, TROWEL APPLIED, ELASTOMERIC, MOISTURE CURE URETHANE
MEMBRANE. APPLY WITH 3/16" X 5/32" V-NOTCH TROWEL IS RECOMMENDED.
6. VINYL BASE: PROVIDE 1/8" COVED BASE FOR HARD FLOOR SURFACES AND STRAIGHT (TOP SET)
BASE FOR CARPETED AREAS. PROVIDE PRE-MOULDED END STOPS AND EXTERNAL CORNERS.
COLOR, TYPE AND HEIGHT AS SHOWN ON THE DRAWINGS.
4
5
6
7
8
9
10
FINISH COAT).
b. FINISH: APPLY TWO (2) COATS OF REGAL SELECT PREMIUM INTERIOR PAINT SEMI-GLOSS
c. APPLICATION: BRUSH APPLY WITH PREMIUM QUALITY NYLON/POLYESTER BRUSH. PRIMER
MAY BE SPRAYED. ALWAYS KEEP A WET EDGE DURING APPLICATION. A MAXIMUM OF ONE
PINT PER GALLON OF CLEAN WATER MAY BE ADDED FOR A DESIRED CONSISTENCY AND
FLOW.
15.5 METAL DOORS AND METAL DOOR JAMBS - SEMI GLOSS FINISH
a. PRIMER: APPLY ONE (1) COAT OF SUPER SPEC HP ACRYLIC METAL PRIMER (P04) AT A WET
FILM THICKNESS OF 4.0-4.5 MILS PER COAT TO ACHIEVE A DRY FILM THICKNESS OF
1.7-2.3 MILS PER COAT. (TINT PRIMER ONE SHADE LIGHTER THAN FINISH COAT).
b. FINISH: APPLY TWO (2) COATS OF REGAL SELECT PREMIUM INTERIOR PAINT SEMI-GLOSS
c. APPLICATION: FOR JAMBS: BRUSH APPLY WITH PREMIUM QUALITY
NYLON/POLYESTER BRUSH. ALWAYS KEEP A WET EDGE DURING APPLICATION. FOR DOORS,
A SOFT WOVEN COVER OF NO MORE THAN ½” IS RECOMMENDED
FOR A SMOOTH
APPEARANCE. A MAXIMUM OF ONE PINT PER GALLON OF CLEAN WATER MAY BE ADDED
FOR A DESIRED CONSISTENCY AND FLOW.
15.6 CONCRETE FLOOR SEALERS: PROVIDE AS INDICATED ON THE DRAWINGS OR, IF NOT
INDICATED THERE PROVIDE AS FOLLOWS FOR ALL EXPOSED CONCRETE AREAS WITHOUT A
SPECIFIED FINISH
a. INTERIOR CLEAR CONCRETE FLOOR SEALER (WATER-BASED) MP1#58, H&C SILICONE
ACRYLIC CONCRETE SEALER, APPLIED PER MANUFACTURER'S WRITTEN INSTRUCTIONS.
b. EXTERIOR CLEAR CONCRETE SEALER MP1#99, H&C CONCRETE & MASONRY WATER
PROOFING SEALER, APPLIED PER MANUFACTURER'S RECOMMENDATIONS.
15.7 NOTES AND CAUTIONS
a. ENSURE PROPER CONDITIONS FOR APPLICATION - BEFORE ANY SURFACE IS COATED, IT
SHALL BE CLEANED OF ALL DUST, DIRT, GREASE, LOOSE RUST, MILL SCALE, LOOSE PAINT,
ETC. IMPERFECTIONS AND HOLES IS SURFACES TO BE COATED SHALL BE CLEANED AND
FILLED IN AN APPROVED MANNER.
b. ALL PROJECTS SHOULD BE INSPECTED - AT VARIOUS STAGES OF SURFACE PREPARATION
AND COATING APPLICATION. INSPECTIONS SHOULD BE CARRIED OUT BY G.C. INSPECTION
& OWNERS REP. OR BY OUTSIDE INSPECTION FIRMS.
c. CLEAN ANY BOLTS AND PAINT THEM USING A BRUSH - COLORS SHOULD BE DEGREASED
BEFORE PRIMING. THE PRIMER AND TOPCOATS SHOULD BE APPLIED BY BRUSH TO
ACHIEVE COMPLETE AND UNIFORM COVERAGE.
d. MASK FAYING SURFACES AFTER PRIMING - IF FAYING SURFACES ARE TO BE PRIMED, THEY
MUST BE MASKED AFTER PRIMING TO PREVENT TOPCOATING OF THE FAYING SURFACES.
APPLICATION OF THE TOPCOAT TO A FAYING SURFACE MY LEAD TO LOOSENING OF
FRICTION JOINTS.
e. ENSURE ADEQUATE VENTILATION - ADEQUATE VENTILATION WHILE APPLYING AND CURING
COATINGS IS IMPORTANT FOR HEALTH AND SAFETY REASONS AND TO ENSURE PROPER
CURING OF THE COATING. WHEN APPLYING COATINGS IN CONFINED SPACES, SOLVENT
VAPORS MAY ACCUMULATE, LEADING TO INTOXICATION OF WORKERS OR FIRE AND
EXPLOSION. FLAMMABLE SOLVENTS AND THE ATOMIZED COATINGS ARE GENERALLY
HEAVIER THAN AIR AND TEND TO SETTLE IN THE LOWER AREAS OF CONFINED CONSIDER
THIS WHEN DESIGNING AND INSTALLING THE VENTILATION SYSTEM.
f. PAINT BEFORE INSTALLING HARDWARE.
G.
1. GENERAL: INSTALL VINYL WALL COVERING AND PROVIDE ACCESSORIES AS REQUIRED FOR
COMPLETE FINISHED INSTALLATION.
2. MAINTENANCE INSTRUCTIONS: FURNISH MANUFACTURER'S RECOMMENDED CLEANING
MATERIALS AND APPLICATION METHODS, INCLUDING PRECAUTIONS IN USE OF CLEANING
MATERIALS WHICH MAY BE DETRIMENTAL TO SURFACES.
3. MANUFACTURER: AS NOTED ON DRAWINGS.
4. TYPE: VINYL WALL COVERING CONFORMING TO FS DD-G-408, TYPE II VINYL WALL COVERING
WITH CLOTH BACKING, MINIMUM 24 TO 26 OZ.; WITH MAXIMUM 25 FLAME SPREAD AND
SMOKE DEVELOPED, ASTM E84 (UL CLASS A, UBC CLASS I).
5. ADHESIVE: NONTOXIC TYPE RECOMMENDED BY WALL COVERING MANUFACTURER TO SUIT
APPLICATION.
6. PRIMER: PROVIDE NON-STAINING, NON-TOXIC RELEASE COAT PRIMER AS RECOMMENDED BY
WALL COVERING MANUFACTURER.
a. PROVIDE PRIMER WHICH ALLOWS REMOVAL OF WALL COVERING FROM GYPSUM BOARD
WITHOUT DAMAGING PAPER FACING OF BOARD, AND WITHOUT PREMATURE SEPARATION
OF WALL COVERING FROM WALL.
7. EXAMINATION: ENSURE SURFACES TO RECEIVE WALL COVERING ARE CLEAN, TRUE AND FREE OF
IRREGULARITIES, DO NOT COMMENCE WITH WORK UNTIL SURFACES ARE SATISFACTORY.
a. ENSURE WALL SURFACE FLATNESS TOLERANCE DOES NOT VARY MORE THAN 1/8" IN
10'-0", NOR VARY AT A RATE GREATER THAN 1/16" PER RUNNING FOOT.
8. PREPARATION: COMPLY WITH MANUFACTURER'S RECOMMENDATIONS; FILL NICKS, GOUGES AND
OTHER MINOR IMPERFECTIONS OF SUBSTRATES WITH LATEX FILLER; SAND SMOOTH, FLUSH
WITH SURFACE; APPLY PRIME COAT IN ACCORDANCE WITH MANUFACTURER'S
RECOMMENDATIONS.
9. APPLICATION: HANDLE AND APPLY WALL COVERING IN ACCORDANCE WITH MANUFACTURER'S
RECOMMENDATIONS AND INSTALLATION INSTRUCTIONS; MIX AND APPLY ADHESIVE IN
ACCORDANCE WITH ADHESIVE MANUFACTURER'S RECOMMENDATIONS.
a. USE FABRIC PANELS IN EXACT ORDER AS CUT FROM ROLLS; USE ROLLS IN CONSECUTIVE
ORDER AS NUMBERED BY MANUFACTURER.
b. HORIZONTAL SEAMS AND CUTTING AT CORNERS ARE NOT ACCEPTABLE; CUT NO CLOSER
THAN 2" OF AN INSIDE CORNER, AND NOT CLOSER THAN 6" OF AN OUTSIDE CORNER.
c. FILL SPACES ABOVE AND BELOW WINDOWS, DOORS, AND SIMILAR AREAS IN SEQUENCE
FROM ROLL.
11
H.
1.
2.
3.
4.
5.
6.
7.
I.
1.
2.
J.
1.
2.
K.
1.
2.
3.
12
13
14
GENERAL: PROVIDE TOILET ACCESSORIES AS REQUIRED FOR COMPLETE FINISHED
INSTALLATION.
CODES AND REGULATIONS: COMPLY WITH STATE AND FEDERAL REQUIREMENTS FOR ENSURING
ACCESS FOR PERSONS WITH DISABILITIES.
MANUFACTURERS: AS NOTED ON DRAWINGS.
TYPES: STAINLESS STEEL ACCESSORIES AS INDICATED ON DRAWINGS; PROVIDE GRAB BARS
WITH CONCEALED MOUNTING, SIZES AND SHAPES AS INDICATED AND AS REQUIRED BY
APPLICABLE CODES AND REGULATIONS.
MATERIALS: STAINLESS STEEL, ASTM A666, COMMERCIAL GRADE, TYPE 302/304, NUMBER 4
SATIN FINISH, SATIN CHROME ACCEPTABLE WHERE STAINLESS STEEL IS NOT AVAILABLE FOR
ACCESSORY ITEM SCHEDULED; GAGES AS STANDARD WITH MANUFACTURER OF SPECIFIED
ITEMS.
a. FASTENERS, SCREWS, AND BOLTS: HOT DIP GALVANIZED; AS RECOMMENDED BY
ACCESSORY MANUFACTURER FOR COMPONENT AND SUBSTRATE.
b. CONCEALED SURFACES: PRETREAT AND CLEAN, SPRAY APPLY ONE COAT PRIMER AND
BAKED ENAMEL FINISH.
FABRICATION: WELD AND GRIND SMOOTH JOINTS OF FABRICATED COMPONENTS; FORM
EXPOSED SURFACES FROM ONE SHEET OF STOCK, FREE OF JOINTS.
a. FABRICATE UNITS WITH TIGHT SEAMS AND JOINTS, EXPOSED EDGES ROLLED; HANG
DOORS AND ACCESS PANELS WITH CONTINUOUS PIANO HINGES; PROVIDE CONCEALED
ANCHORAGE WHERE POSSIBLE.
b. PROVIDE STEEL ANCHOR PLATES AND ANCHOR COMPONENTS FOR INSTALLATION.
c. FORM SURFACES FLAT WITHOUT DISTORTION; MAINTAIN FLAT SURFACES WITHOUT
SCRATCHES AND WITHOUT DENTS; FINISH EXPOSED EDGES EASED, FREE OF SHARP
EDGES WHERE POTENTIAL EXISTS FOR PHYSICAL CONTACT.
d. HOT DIP GALVANIZE FERROUS METAL ANCHORS AND FASTENING DEVICES.
e. SHOP ASSEMBLE COMPONENTS; PACKAGE COMPLETE WITH ANCHORS AND FITTINGS.
INSTALLATION: COMPLY WITH MANUFACTURER RECOMMENDATIONS AND APPLICABLE CODES
AND REGULATIONS.
9
10
SEAL
FIRE EXTINGUISHERS, CABINETS, AND ACCESSORIES AS REQUIRED BY APPLICABLE CODE.
a. COMPLY WITH NFPA 10, STANDARD FOR PORTABLE FIRE EXTINGUISHERS.
b. LISTED AND LABELED FOR TYPE, RATING, AND CLASSIFICATION BY AN INDEPENDENT
TESTING AGENCY ACCEPTABLE TO AUTHORITIES HAVING JURISDICTION.
PRODUCTS
a. FIRE EXTINGUISHERS: PORTABLE MULTIPURPOSE DRY-CHEMICAL TYPE, UL RATED 4-A:
60-B:, 10-LB NOMINAL CAPACITY, IN ENAMELED STEEL CONTAINER.
b. FIRE EXTINGUISHER CABINETS: SIZED TO FIT FIRE EXTINGUISHER; APPROVED BY
ARCHITECT.
GENERAL: INSTALL STORAGE SHELVING AS INDICATED ON THE DRAWINGS; PROVIDE
ACCESSORIES AS REQUIRED FOR COMPLETE FINISHED INSTALLATION.
INSTALLATION: COMPLY WITH MANUFACTURER RECOMMENDATIONS AND INSTALLATION
INSTRUCTIONS. INSTALL UNITS AND ACCESSORIES AT LOCATIONS SHOWN IN ACCORDANCE
WITH MANUFACTURER'S RECOMMENDATIONS AND INSTALLATION INSTRUCTIONS, LEVEL, PLUMB,
SECURE AND AT PROPER HEIGHT
PROVIDE SIGNAGE AS INDICATED ON THE DRAWINGS. COMPLY WITH APPLICABLE PROVISIONS IN
ADA-ABA ACCESSIBILITY GUIDELINES AS APPLICABLE
ALL COLORS, TYPE, STYLE, FONT SIZE AND MATERIALS TO BE AS SHOWN ON DRAWINGS AND
AS SELECTED AND APPROVED BY OWNER.
LOCATE SIGNS WHERE INDICATED, USING MOUNTING METHODS OF TYPES DESCRIBED AND
COMPLYING WITH MANUFACTURER'S WRITTEN INSTRUCTIONS, EXCEPT WHERE MORE STRINGENT
REQUIREMENTS APPLY.
A. GENERAL CONTRACTOR IS RESPONSIBLE FOR ASSEMBLY AND PLACEMENT OF OFFICE AND
NON-SALES EQUIPMENT AND FURNITURE.
B. THE CONTRACTOR IS RESPONSIBLE TO UNCRATE, ASSEMBLE, AND PLACE TRADE FIXTURES AND
PRESENTATION ITEMS IN SALES AREA; FIXTURES TO BE LOCATED PER THE DIRECTION OF THE
OWNER.
A. ACCESS PANEL: FOR GYPSUM BOARD SOFFIT OR WALL (COLOR TO MATCH ADJACENT FINISH):
24" X 24" SURFACE MOUNTED, MODEL #AP24, AS MANUFACTURED BY INTEXFORMS INC. (916)
388-9933 OR OTHER WHICH MUST BE APPROVED BY OWNERS CONSTRUCTION MANAGER.
SUBSTITUTE WITH "B" LABEL FIRE PANEL, MODEL FW 5050, KEY LOCK, ONLY IF A RATED DOOR
IS REQUIRED PER CODES.
B. ACCESS PANELS: FOR HVAC EQUIPMENT ARE NORMALLY INDICATED ON THE HVAC AND
REFLECTED CEILING PLANS. IN ABSENCE OF DEFINED LOCATIONS, THE GENERAL CONTRACTOR
IS TO FURNISH AND INSTALL ACCESS PANELS AS NECESSARY TO FURNISH REASONABLE, SAFE
ACCESS TO SERVICE ALL SERVICEABLE COMPONENTS OF EACH PIECE OF EQUIPMENT.
ASSUMED ACCESS SHALL BE BY A TECHNICIAN(S) STANDING FIRMLY ON A LADDER. WHERE
ACCESS PANELS OR REMOVABLE DIFFUSERS CANNOT BE LOCATED IMMEDIATELY ADJACENT TO
THE EQUIPMENT,
C. THE GENERAL CONTRACTOR IS RESPONSIBLE TO ASSEMBLE ALL MISCELLANEOUS NON-SALES
AREA WALL STANDARDS, SHELVES, BRACKETS, ETC.
D. LAVATORY FIXTURES & ACCESSORIES: REFER TO MECHANICAL DRAWINGS, TOILET ROOM
DETAILS SHEET, AND RESPONSIBILITY SCHEDULE.
E. RESTORE LANDLORD'S STRUCTURAL STEEL FIREPROOFING TO MAINTAIN INTEGRITY OF SAME AND
FIREPROOF NEW STEEL AS REQUIRED.
F. CLEANING: THE G.C. IS RESPONSIBLE FOR 2 PROFESSIONAL CLEANINGS. ONE CLEANING TO BE
PRIOR TO THE PUNCH-LIST DATE. THE SECOND IS TO BE AFTER THE STORE IS MERCHANDISED
BEFORE THE OPENING DATE. STORE IS TO BE TURNED OVER IN A DUST-FREE, DIRT-FREE
CONDITION. CLEANING SHALL INCLUDE, BUT NOT BE LIMITED TO THE FOLLOWING:
1. STOREFRONT GLASS (INSIDE AND OUT)
2. MIRRORS
3. STOREFRONT METAL
4. SIGNS
5. LIGHT FIXTURES INCLUDING CANS, TRIM, TRACK AND TRACK HEADS
6. FLOORING (PER MANUFACTURER'S RECOMMENDATIONS)
7. VINYL RESILIENT FLOOR TILE CLEANED AND WAXED
8. PRESENTATION ITEMS, PROPS, AND TRADE FIXTURES
9. WOOD BASE
10. WALL COVERINGS
11. NON-SALES SHELVING, STORAGE PLATFORMS, ETC.
G.
- GENERAL: G.C. TO COORDINATE AWNING AND FRAME INSTALLATION WITH OWNER'S
PROJECT MANAGER. SUBCONTRACTOR TO PROVIDE BLOCKING AS REQUIRED. COORDINATE
WITH OWNER'S VENDOR.
8
Mason, Ohio 45040
AT
2
RIVERCHASE GALLERIA
1
E.
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
DRAWN BY: PWD
AUTHORIZED FOR:
ARCHITECTURAL
SPECIFICATIONS
A-702
11
12
13
14
3
4
5
6
7
8
9
10
11
KEY NOTES
J
H
1.
2.
K
ADJACENT
TENANT (N.I.C.)
TOILET
ROOM
102
A-16 A-1
3.
6
A-20
16
5
PANEL 'HP'
XFMR
4.
10
A-19
TO LIGHT
SEE E-102
J
PANEL 'A'
TIME CLOCK &
CONTACTORS
13
A-19
4
5.
A-24
11
9
18
A-5
7
S
20
21
13
6.
7.
EX VAV
14
3
10.
100
16 A-10
STUB-UP
(TYPICAL)
H
12 (TYP)
SALES
15
ON
8.
9.
(E)
11.
22
12.
13.
14.
15.
16.
17.
COL
MALL COMMON
AREA (N.I.C.)
G
ADJACENT
TENANT (N.I.C.)
18.
19.
14
5
20.
2
(E)
A-7
6
F
21.
4
NORTH
A-14
22.
FURNISH AND INSTALL FLOOR MOUNTED RECEPTACLE. SEE DIMENSION PLAN THIS
SHEET FOR LOCATION.
FURNISH AND INSTALL FLOOR MOUNTED POWER/DATA COMBINATION. CONTRACTOR
SHALL FURNISH AND INSTALL (1) 1-1/4" CONDUIT WITH CAT6 CABLE PULLED BACK
TO RACK FOR DATA OUTLET, SEE DIMENSION PLAN THIS SHEET FOR LOCATION. ON
DEDICATED 24 HOUR CIRCUIT.
CONDUIT FOR CASH REGISTER POWER CIRCUIT. COORDINATE INSTALLATION
REQUIREMENTS WITH CONSTRUCTION MANAGER AND MILLWORK CONTRACTOR .
CHECK LENGTH OF SCREWS BEFORE ATTACHING OUTLETS TO MILLWORK. VERIFY
SCREWS ARE NOT TOO LONG AND WILL NOT DAMAGE OTHER SIDE OF MILLWORK
WHEN TIGHTENED. TRENCH AND PATCH FLOOR AS REQUIRED, COORDINATE
LOCATION IN FIELD WITH LANDLORD'S REPRESENTATIVE AND OWNER'S FIELD
REPRESENTATIVE PRIOR TO ROUGH-IN .
PROVIDE (1) 1" CONDUIT FOR POWER BELOW FLOOR. COORDINATE TRENCH
LOCATIONS IN FIELD WITH LANDLORD'S REPRESENTATIVE. REPAIR FLOOR TO MATCH
EXISTING CONDITIONS.
PROVIDE (1) 1-1/4" CONDUIT FOR TELE/DATA BELOW FLOOR. COORDINATE TRENCH
LOCATIONS IN FIELD WITH LANDLORD'S REPRESENTATIVE. REPAIR FLOOR TO MATCH
EXISTING CONDITIONS. EXTEND CONDUIT FOR TELE/DATA TO TELE/DATA
DISTRIBUTION EQUIPMENT.
EXTEND CONDUIT TO TECH RACK DISTRIBUTION EQUIPMENT.
EXISTING TELEPHONE BOARD WITH SURFACE MOUNTED QUAD RECEPTACLE TO
REMAIN.
REFER TO ELEVATION SHEET A-502 FOR MORE INFORMATION.
EXISTING TIME CLOCK AND CONTACTORS REFER TO ONE LINE DIAGRAM FOR
ADDITIONAL INFORMATION. SEE LIGHTING CONTROL DETAIL ON E-501.
EXISTING ELECTRICAL DISTRIBUTION EQUIPMENT TO REMAIN. TRANSFORMER TO BE
RELOCATED ABOVE CEILING. SEE ONE LINE DIAGRAM ON SHEET E-601.
FURNISH AND INSTALL (1) DUPLEX RECEPTACLE MOUNTED AT 2'-6" A.F.F. (TO CENTER
OF DEVICE) FOR FRAME WARMER.
EXISTING RECEPTACLE MOUNTED ON CEILING FOR SHOW WINDOW AS REQUIRED BY
N.E.C.
FURNISH AND INSTALL RECEPTACLE FOR POWER OF DISPLAY CASES BELOW BASE
OF MILLWORK SO CORDS AND RECEPTACLE ARE CONCEALED BEHIND FIXTURES.
COORDINATE EXACT LOCATION WITH MILLWORK VENDOR.
EXISTING MECHANICAL EQUIPMENT TO REMAIN.
EXISTING INSTANTANEOUS WATER HEATER TO REMAIN. SEE EQUIPMENT CONNECTION
SCHEDULE ON SHEET E-601.
CONTROL CIRCUIT THROUGH LIGHTING SWITCH BANK. SEE DETAIL ON SHEET E-501.
FURNISH AND INSTALL GFI DUPLEX RECEPTACLE ADJACENT TO UNIT IF NOT
EXISTING/FURNISHED WITH EQUIPMENT. CIRCUIT AS INDICATED, FURNISH WEATHER
PROOF ENCLOSURES AND COVERS AS REQUIRED.
EXISTING THERMOSTAT/REMOTE SENSOR TO REMAIN.
DUCT SMOKE DETECTOR/REMOTE TEST STATION: DUCT MOUNTED SMOKE
DETECTOR IS FIELD INSTALLED. CONTRACTOR SHALL INTERLOCK SMOKE DETECTOR
WITH HVAC UNIT, REMOTE TEST ALARM STATION AND FIRE ALARM SYSTEM (IF
APPLICABLE). MAKE ALL FINAL CONNECTIONS AS REQUIRED FOR A COMPLETE
SYSTEM. HVAC UNIT TO SHUT DOWN UPON ACTIVATION OF SMOKE DETECTOR.
COORDINATE WITH LANDLORD TO AVOID CONFLICTS IN FIEL D.
EXISTING FIRE ALARM CONTROL PANEL TO REMAIN. FIELD VERIFY EXACT LOCATION
AND REQUIREMENTS PRIOR TO BID.
EXISTING FIRE ALARM MANUAL PULL STATION TO REMAIN. FIELD VERIFY EXACT
LOCATION AND REQUIREMENTS.
EXISTING FIRE ALARM HORN/STROBE TO REMAIN. FIELD VERIFY EXACT LOCATION AND
REQUIREMENTS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
F1
SCALE:
12
POWER PLAN
J
21.
H
22.
E
23.
24.
14
26.
27.
REFER TO MECHANICAL PLAN FOR LOCATION OF MECHANICAL EQUIPMENT. FIELD
VERIFY EXACT LOCATIONS. PROVIDE AND INSTALL ALL CONVENIENCE RECEPTACLES,
SAFETY SWITCHES, WIRING, OR OTHER EQUIPMENT TO ENSURE A COMPLETE AND
OPERABLE HVAC SYSTEM.
ALL WALL MOUNTED RECEPTACLES, SWITCHES, AND COVERPLATES SHALL MATCH
WALL, REFER TO SHEET A-201FOR FINISHES. THE CEILING RECEPTACLES AND
COVERPLATES SHALL MATCH CEILING.
CONDUIT FOR DATA/TELEPHONE OUTLETS SHALL HAVE NO MORE THAN THREE 90°
BENDS. IF THE CONDUIT RUN REQUIRES MORE THAN THREE 90° BENDS, PROVIDE
A PULL/JUNCTION BOX AFTER EACH SET OF THREE 90° BENDS.
LABEL ALL COVERPLATES ON INSIDE FACE OF PLATE WITH CIRCUIT NUMBER AND
PANEL DESIGNATION. I.E. "A-1". CIRCUIT SHALL BE WRITTEN WITH PERMANENT
MARKER IN A CONTRASTING COLOR.
ALL TELEPHONE/DATA CABLING TO BE RUN IN CONDUIT TO 6" ABOVE CEILING.
PROVIDE 6' OF EXTRA CABLING AT ALL TELEPHONE/DATA TERMINATIONS. ALL
CABLING SHALL BE PLENUM RATED. RUN PHONE/DATA CABLING (CAT 6)
COMPLETELY IN CONDUIT IF LOCAL CODES/MUNICIPALITIES REQUIRE IT (FIELD
VERIFY). ALL CABLING SHALL BE ROUTED AWAY FROM ALL ELECTRIC EQUIPMENT
(WITHIN 18") AND SECURED TO STRUCTURE ABOVE. ALL TELEPHONE/DATA
CABLING FURNISHED & INSTALLED BY ELECTRICAL CONTRACTOR.
ALL MOUNTING HEIGHTS FROM THE CENTERLINE OF THE BOX TO THE FINISHED
FLOOR ARE AS FOLLOWS, UNLESS NOTED OTHERWISE ON PLAN: SWITCHES-48",
ELECTRICAL/TELEPHONE/DATA OUTLETS-18", THERMOSTATS-5'-0", TOP OF
PANELBOARDS-6'-6".
ALL ROOF PENETRATIONS TO BE COORDINATED WITH THE LANDLORD'S DESIGNATED
ROOFING CONTRACTOR.
FLEXIBLE CONDUIT SHALL BE USED FOR ALL FINAL CONNECTIONS TO MILLWORK,
INTERIOR LIGHTING FIXTURES, AND EQUIPMENT. MAXIMUM LENGTH OF FLEXIBLE
CONDUIT SHALL BE 6'-0".
CONDUIT AND OUTLETS FOR SECURITY, DATA, TELEPHONE, AND ELECTRIC MAY
REQUIRE REMOVAL OF CONCRETE SLAB OR ROUTING OF CONDUIT UNDER FLOOR
IN SPACE BELOW. ALL WORK TO BE COORDINATED WITH THE LANDLORD
DISCONNECT SWITCHES SHALL BE GENERAL DUTY IN APPROPRIATE NEMA
ENCLOSURES. A LINE VOLTAGE, HORSEPOWER RATED DISCONNECT SWITCH
SHALL BE INSTALLED ADJACENT TO EACH MOTOR.
TRANSFORMER NEUTRALS SHALL BE SECURELY GROUNDED TO THE BUILDING STEEL
AND COLD WATER PIPING PER THE N.E.C. AND LOCAL CODE REQUIREMENTS.
INSTALL TRANSFORMERS ON VIBRATION ISOLATION PADS.
ELECTRICAL EQUIPMENT EXPOSED TO WEATHER MUST BE WEATHERPROOF.
ALL TEMPORARY WIRING SHALL BE REMOVED WHEN PERMANENT POWER IS
AVAILABLE.
IF INSTALLATION VARIES FROM THE CONTRACT DRAWINGS, THE GENERAL
CONTRACTOR WILL BE RESPONSIBLE FOR OBTAINING "AS BUILT" DRAWINGS FROM
THE SUBCONTRACTORS AND SUBMITTING SAME TO SUN GLASS HUT.
CONTRACTOR SHALL PURCHASE AT SGH NATIONAL ACCOUNT AGREED PRICING, ALL
DISCONNECT SWITCHES, ELECTRIC DISTRIBUTION PANELS, TRANSFORMERS,
CIRCUIT BREAKERS AND FUSES. CONTACT SUN GLASS HUT'S NATIONAL ACCOUNT
REPRESENTATIVE FOR PRICING INFORMATION AND INCLUDE IN BID.
SEE ARCHITECTURAL ELEVATIONS FOR ADDITIONAL INFORMATION ON PLACEMENT
OF OUTLETS & SWITCHES.
FOR ALL CASHWRAP MILLWORK ELECTRIC, DATA, AND TELEPHONE OUTLETS, REFER
TO THE DETAILS ON SHEET E-501.
ALL DATA/PHONE CABLING MUST BE PROPERLY IDENTIFIED WITH NUMBER AND/OR
COLOR SYSTEM AT BOTH ENDS.
ANY PENETRATIONS THROUGH FIRE-RESISTANT/RATED WALLS, PARTITIONS,
FLOORS, AND CEILINGS SHALL BE FIRESTOPPED USING APPROVED UL METHODS
TO MAINTAIN THE FIRE RESISTANCE RATING.
RECEPTACLE CIRCUITS UP TO 100'-0" IN LENGTH SHALL UTILIZE #12 CONDUCTORS
MINIMUM. RECEPTACLE CIRCUITS FROM 101'-0" TO 150'-0" IN LENGTH SHALL
UTILIZE #10 CONDUCTORS MINIMUM. RECEPTACLE CIRCUITS FROM 151'-0" TO
250'-0" IN LENGTH SHALL UTILIZE #8 CONDUCTORS MINIMUM. RECEPTACLE
CIRCUITS ABOVE 250'-0" IN LENGTH SHALL UTILIZE #6 CONDUCTORS MINIMUM.
ELECTRICAL CONTRACTOR SHALL PROVIDE JUNCTION BOX AND RACEWAY FOR
THERMOSTATS AT 60" A.F.F. THERMOSTATS AND TEMPERATURE SENSORS
INSTALLED AND WIRED BY MECHANICAL CONTRACTOR. COORDINATE EXACT
LOCATIONS WITH MECHANICAL CONTRACTOR. TYPICAL OF ALL.
DUCTWORK AND PIPING SHALL NOT BE ROUTED OVER ELECTRIC PANELS OR
TRANSFORMERS.
IT IS THE RESPONSIBILITY OF THE ELECTRICAL CONTRACTOR TO REVIEW ALL
ARCHITECTURAL, MECHANICAL, PLUMBING, STRUCTURAL, FIRE ALARM AND FIRE
PROTECTION AND ELECTRICAL DRAWINGS AND NOTES TO ENSURE THAT ALL
ELECTRICAL REQUIREMENTS ARE MET.
ALL WORK SHALL BE IN STRICT ACCORDANCE WITH NATIONAL ELECTRICAL CODE
AND ALL LOCAL CODES AND ORDINANCES.
GC'S ELECTRICIAN TO PULL ALL LOW VOLTAGE TELEPHONE AND DATA LINES
INCLUDING INSTALLATION OF DEVICES. PUNCH DOWN OF LINE(S) AT THE TERMINAL
BOARD IS BY OTHERS.
REFER TO SHEET E-501 FOR ABBREVIATIONS AND SYMBOLS
REFER TO SHEET G-002 FOR RESPONSIBILITY SCHEDULE.
Mason, Ohio 45040
Shremshock Engineering, Inc.
SEAL
D
22'-3"
7'-9"
C
RIVERCHASE GALLERIA
COL
B
SPACE #236A
2.0 TYPE: PREMIUM
14
SGH STORE #: 4933
DRAWN BY: SRH
REVIEWED BY: RAP
AUTHORIZED FOR:
1
"
'-6
PLOTTED: 7/9/2015 - 12:50 PM
P:\SGH\150066 SGH-Riverchase Galleria Birmingham, AL\E-101_04933.dwg
LAYOUT: E-101
25.
USER: SHOLLAND
13
GENERAL NOTES
AT
2
RIVERCHASE GALLERIA
1
POWER PLAN
A
NORTH
A1
SCALE:
E-101
DIMENSION PLAN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
3
4
5
6
7
8
9
10
11
KEY NOTES
1.
LIGHTING SPECIFICATIONS
K
MARK
TYPE SUPPLIER
A3W
A3B
J
A3W
A3B
CONTECH
LIGHTING
CONTECH
LIGHTING
(E)
(E)
EXISTING
PRODUCT TYPE
WATT
#LP
LAMP
CTL830P
13
N/A
LED12P30SD30KNFL
CTL830B
13
N/A
39
2
LED 12P30SD30KNFL
LED TRACK HEAD - FRONT LOADING PAR30 GIMBAL RING TRACKHEAD
WHITE FINISH RESTICKER FOR 13 WATTS
LED TRACK HEAD - FRONT LOADING PAR30 GIMBAL RING TRACKHEAD
WHITE FINISH RESTICKER FOR 13 WATTS
4.
PAR20
EXISTING DUAL LAMP RECESSED LUMINARIES
5.
(E)
(E)
EXISTING
42
1
42W TRIPLE TUBE 4 PIN
EXISTING DUAL LAMP RECESSED LUMINARIES
6.
TB4'-0"
TB
CONTECH
LIGHTING
LT-(2, 4, 6, 8)-B
N/A
N/A
N/A
PROVIDE TRACK, LENGTH AS INDICATED, BLACK FINISH. SOME
PIECES WILL BE FIELD CUT TO MATCH LENGTH SHOWN ON PLANS.
PROVIDE END FEEDS AND CONNECTORS AS REQUIRED.
7.
8.
TW4'-0"
TW
CONTECH
LIGHTING
LT-(2, 4, 6, 8)-P
N/A
N/A
N/A
(R)
(R)
RELOCATED
42
1
42W TRIPLE TUBE 4 PIN
RELOCATED DUAL LAMP RECESSED LUMINARIES
(E)
EXISTING
32
1
32W T8
EXISTING 4' SURFACE MOUNTED SINGLE TUBE STRIP
(E)
CIRCUIT VIA MASTER LIGHTING SWITCH BANK. SEE LIGHTING CONTROL DETAIL ON
E-501.
CIRCUIT SHOW WINDOW & SIGN LIGHTING THROUGH TIME CLOCK.
FURNISH AND INSTALL JUNCTION BOX AND DISCONNECT TOGGLE TYPE SWITCH
WITH MINIMUM 12" WHIP PER N.E.C. LOCATE ABOVE CEILING NEAR ACCESS PANEL
IN CONCEALED LOCATION. CIRCUIT THROUGH TIMECLOCK/CONTACTOR. SEE
ARCHITECTURAL SHEETS FOR SIGN LOCATION.
FURNISH AND INSTALL GANGED SWITCH FOR LOCAL LIGHTING SWITCHES. PROVIDE
COMMON FACEPLATE OR MULTIPLE FACEPLATES OF EQUAL WIDTHS. SEE LIGHTING
CONTROL DETAIL ON E-501.
CONNECT EMERGENCY FIXTURE TO EMERGENCY/NIGHT LIGHTING CIRCUIT (A-22)
PER NEC 700-12(A) AND LIFE SAFETY CODE.
EMERGENCY FIXTURE TO BE SERVED BY LOCAL LIGHTING CIRCUIT AHEAD OF ALL
SWITCHING. PER NEC 700-12(A) AND LIFE SAFETY CODE.
FURNISH AND INSTALL WALL MOUNTED OCCUPANCY SENSOR
FURNISH AND INSTALL CONDUIT FROM TECH RACK TO 24" ABOVE CEILING FOR
TERMINATION AT TRAFFIC COUNTER PROVIDE CAT6 DATA CABLE WITH MINIMUM
6FT COILED CABLE AT BOTH ENDS.
FURNISH AND INSTALL CONDUIT FROM TECH RACK TO 24" ABOVE CEILING FOR
TERMINATION AT WIRELESS POWER INJECTOR BRICK/WIRELESS ACCESS POINT
PROVIDE CAT6 DATA CABLE WITH MINIMUM 6FT COILED CABLE AT BOTH ENDS.
EXISTING SECURITY CAMERA FOR CCTV SYSTEM TO REMAIN.
18"x18" CORIAN ACCESS PANEL
2.
3.
DESCRIPTION
9.
10.
11.
12
13
14
GENERAL NOTES
H
G
NOTE: NOT ALL FIXTURES MAY BE USED ON THIS PROJECT
F
1.
EMERGENCY (EM) LUMINAIRES SHALL BE CIRCUITED WITH AN "UNSWITCHED HOT"
TO PROVIDE CONTINUOUS POWER TO BATTERY PACK EVEN WHEN LUMINAIRE IS
OFF.
2. ALL NIGHT-LIGHT (NL) LUMINAIRES SHALL BE CIRCUITED AHEAD OF ANY SWITCHING
3. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO UNLOAD INVENTORY AND
STORE LIGHTING PACKAGE. THE CONTRACTOR SHALL ALSO SHIP ANY EXCESS
MATERIALS BACK TO THE ELECTRICAL PACKAGE DISTRIBUTOR.
4. EXIT LIGHTS AT THE STOREFRONT SHALL BE CEILING MOUNTED AND CENTERED
OVER OPENINGS. EXIT/EMERGENCY LIGHTS AT DOOR TO NON-SALES AREAS SHALL
BE CEILING MOUNTED AND CENTERED ABOVE DOOR. IF PLAN LOCATIONS ARE NOT
ACCEPTABLE, IMMEDIATELY CONTACT SGH PROJECT MANAGER FOR DIRECTION.
5. WHERE DRYWALL CEILINGS ARE USED IN THE SALES AREA, CONTRACTOR SHALL
ARRANGE CIRCUITS TO AVOID THE USE OF JUNCTION BOXES IN INACCESSIBLE
LOCATIONS. THE USE OF JUNCTION BOXES ABOVE DRYWALL CEILINGS SHALL BE
LIMITED TO LOCATIONS NEAR ACCESS FRAMES USED FOR DIFFUSERS AND RETURN
AIR GRILLES OR ACCESS PANELS AS LOCATED ON PLANS. IF PLAN LOCATION IS
NOT ACCEPTABLE, IMMEDIATELY CONTACT SGH PROJECT MANAGER FOR
DIRECTION.
6. LIGHTING CIRCUITS UP TO 100'-0" IN LENGTH SHALL UTILIZE #12 CONDUCTORS
MINIMUM. LIGHTING CIRCUITS FROM 101'-0" TO 150'-0" IN LENGTH SHALL UTILIZE
#10 CONDUCTORS MINIMUM. LIGHTING CIRCUITS FROM 151'-0" TO 250'-0" IN
LENGTH SHALL UTILIZE #8 CONDUCTORS MINIMUM. LIGHTING CIRCUITS ABOVE
251'-0" IN LENGTH SHALL UTILIZE #6 CONDUCTORS MINIMUM.
7. LIGHTING SHALL BE CIRCUITED EXACTLY AS SHOWN ON PLANS. CIRCUITING SHALL
BE THRU-WIRING WHEREVER POSSIBLE. MULTIPLE CONNECTIONS TO A SINGLE
LIGHT FIXTURE FOR VOLTAGE DROP CONDITIONS OR AS A RESULT OF A FIELD
CONDITION ARE ACCEPTABLE. LIGHTING FIXTURES SHALL BE MANUFACTURED TO
ACCOMMODATE THRU-WIRING, ANY RELATED COSTS FOR MULTIPLE CONNECTIONS
SHALL BE INCLUDED IN BID.
8. CONTRACTOR'S BID SHALL INCLUDE THE INSTALLATION OF ALL LUMINAIRES AND
ASSOCIATED LAMPS FURNISHED BY SGH. CONTRACTOR IS RESPONSIBLE TO
ENSURE THE ADJUSTABILITY OF ALL DIRECTIONAL FIXTURES AFTER INSTALLATION
AND SHALL AIM THE FIXTURES PER DIRECTION FROM G.C. LIGHT FIXTURE
SPECIFICATIONS MAY VARY, IF THIS IS THE CASE, CONTRACTOR SHALL CALL THE
LIGHTING DISTRIBUTOR FOR EXACT SPECIFICATION OF LIGHTING FIXTURES. IF THE
CEILING SYSTEMS ARE FIRE RATED, CONTRACTOR SHALL CLOSELY COORDINATE
FIXTURE REQUIREMENTS WITH SGH.
9. EMERGENCY AND EXIT LUMINAIRES SHALL BE INSTALLED AND CIRCUITED PER LOCAL
AND LATEST NATIONAL ELECTRICAL CODES. ALL EMERGENCY AND EXIT FIXTURES
SHALL BE DUAL-VOLTAGE WITH BATTERY BACKUP (120/277 VOLT INPUT). INSTALL
A CENTRAL BATTERY SYSTEM WHERE THE USE OF INDIVIDUAL BATTERY UNITS ARE
PROHIBITED BY LOCAL CODES. IF PLAN LOCATION IS NOT ACCEPTABLE,
IMMEDIATELY CONTACT SGH PROJECT MANAGER FOR DIRECTION.
10. CONTRACTOR SHALL MAKE ALL FINAL CONNECTIONS AS REQUIRED FOR A FULLY
COMPLETE AND OPERABLE SYSTEM.
11. SEE ARCHITECTURAL REFLECTED CEILING PLAN FOR EXACT LOCATION AND
QUANTITY OF LIGHTING FIXTURES.
12. CONTRACTOR IS RESPONSIBLE FOR ALL REFLECTED CEILING PLAN NOTES ON
ARCHITECTURAL DRAWINGS.
13. LOW VOLTAGE WIRING: THE GC IS RESPONSIBLE TO DETERMINE IF LOW VOLTAGE
WIRING IS REQUIRED BY EITHER LL OR BUILDING DEPARTMENT TO BE ENCASED IN
CONDUIT, IF SO, CONDUIT TO BE PROVIDED AND INSTALLED BY GC'S ELECTRICIAN.
14. REFER TO SHEET E-501 FOR SYMBOLS LEGEND.
15. REFER TO RESPONSIBILITY SCHEDULE ON SHEET G-002.
16. CONTRACTOR SHALL RELAMP ALL FIXTURES PRIOR TO STORE OPENING BUT NOT
DURING HEAVY CONSTRUCTION PERIOD.
Mason, Ohio 45040
SEAL
F1
LIGHTING FIXTURE SCHEDULE
J
AT
SCALE:
H
E
9
S
C
(E)
W
A3
W
A3
(E)
1
S
A
X1
W
A3
NL/EM
5
(R)
A-6
A3B
W
A3
A3
B
(E)
A3
B
W
A3
(E)
5
(R)
S
C
A-12
SPEAKER
(TYPICAL)
RIVERCHASE GALLERIA
5
(E)
EM
(E)
(E)
3
COL
(E)
W
A3
14
A-8
W
6
"
'-0
W
A3
SPACE #236A
2.0 TYPE: PREMIUM
1
)T
(N
B
A3B
AP
8
A3
W
(E)
(R)
NL/EM
5
"
W
A3
ADJACENT
TENANT
S
C
(E)
"
'-0
W
A3
(E)
A3
W
(E) S
(E)
(E)
100
A3
W
(E)
A3W A3W A3W
(E)
(E)
SALES
11
C
(E)
1
(E)
NL/EM 5
(E)
A3W A3W
(N) TW6'-0"
A3W A3B
A-2
(E)
S (N)
S
C
(N) TW5'-0"
A3
B
(E)
A3W A3W A3W A3W A3W
TB5'-0"
A3W A3W A3W
6'
-0
(E)
A3W A3W A3W
(N) TW8'-0"
3
1
A-4
TW
S
C
(E)
10
(E)
TW
2
W
A3
W
A3
W
A3
PLOTTED: 7/9/2015 - 1:23 PM
10 (TYP)
S
7
D
W
A3
USER: SHOLLAND
2
A-15
4
SSS
LAYOUT: E-102
TOILET
ROOM
RIVERCHASE GALLERIA
1
(E)
11
MALL COMMON
AREA (N.I.C.)
SGH STORE #: 4933
DRAWN BY: SRH
(E)
REVIEWED BY: RAP
AUTHORIZED FOR:
(E)
LIGHTING PLAN
& LIGHTING LEGEND
NORTH
A
A1
SCALE:
E-102
LIGHTING PLAN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
3
4
5
6
7
8
9
10
11
12
ELECTRICAL SYMBOLS
K
IG
120 VOLT DUPLEX RECEPTACLE
WP = WEATHERPROOF
GFI = GROUND FAULT INTERRUPTER
@ 16"
120 VOLT IG DUPLEX RECEPTACLE
@ 16"
LIGHTING/POWER PANELBOARD
120 VOLT DOUBLE DUPLEX (QUAD) RECEPTACLE
@ 16"
120 VOLT SIMPLEX RECEPTACLE
@ 16"
208V OR 120/208V RECEPTACLE
@ 16"
120 VOLT DUPLEX RECEPTACLE
CEILING MOUNTED
SF = STOREFRONT
CASH
REGISTER
SUPPLIES
FIRE ALARM CONTROL PANEL
FABP
FIRE ALARM BOOSTER PANEL
FAAP
FIRE ALARM ANNUNCIATOR PANEL (REMOTE)
A
REMOTE ANNUNCIATOR/TEST STATION
S
CEILING MOUNTED PHOTO/IONIZATION DETECTOR
H
CEILING MOUNTED HEAT DETECTOR
S
PHOTO/IONIZATION DETECTOR-DUCT MOUNTED
V
ALARM HORN WITH VISUAL INDICATOR
PANELBOARD
480/277V
(TYP.) 3P BREAKER
BROTHER
PRINTER
PANELBOARD
208/120V
MAIN BREAKER
THERMOSTAT
S
N
HVAC SENSOR
Z
ZONE DAMPER
TELEPHONE OUTLET BOX
@ 16"
DATA OUTLET BOX
@ 16"
DATA/TELEPHONE OUTLET BOX
@ 16"
VISUAL ALARM INDICATOR WITH NO HORN
B
ALARM BELL
S
FIRE ALARM SPEAKER WITH VISUAL INDICATOR
S
FIRE ALARM SPEAKER
F
MANUAL PULL STATION
DATA OUTLET BOX - FLOOR MOUNTED
DATA/TELEPHONE - FLOOR MOUNTED
WALL MOUNTED VOLUME CONTROL
@ 48"
VS
WALL MOUNTED VARIABLE SPEED CONTROLLER
@ 48"
K
KEYPAD
VC
@ 80"
NEUTRAL BAR
P
TC
TRAFFIC COUNTER
AP
WIRELESS ACCESS POINT
PRESSURE SWITCH
TS
TAMPER SWITCH
R
FIRE ALARM RELAY
FIRE ALARM JUNCTION BOX
MAGNETIC DOOR HOLDER-WALL OR FLOOR
MOUNTED AS INDICATED
D
GLASS BREAK SENSOR
@ 48"
OCCUPANCY SENSOR
@ 48"
O
S
OCCUPANCY SENSOR - CEILING MOUNTED
DOUBLE REMOTE HEAD
DS
DAYLIGHT SENSOR
TRACK HEAD
DD
DIMMING SENSOR
WALL MOUNTED FIXTURE
V
VACANCY SENSOR
EM/NL WALL MOUNTED FIXTURE
CURRENT LIMITER - NUMBER INDICATES AMPERAGE
OF BREAKER
RECESSED CAN LIGHT
TIMER SWITCH
@ 48"
D
DIMMER SWITCH
@ 48"
J
N
3
J J J
2
ONE (1) 1" DIA. RIGID CONDUIT FOR
POWER STUBBED BELOW CASHWRAP
BASE (FRAME WARMER AND TECH
RACK)
ONE (1) 1" DIA. RIGID CONDUIT FOR
POWER (IG) STUBBED BELOW CASHWRAP
BASE (1 CIRCUIT)
ONE (1) 1-1/4" DIA. RIGID CONDUIT FOR
TELE/DATA STUBBED BELOW CASHWRAP
BASE. PROVIDE 4 CAT6 CABLES.
CUT HOLES AS REQUIRED
AT REAR OF BASE FOR
FLEX CONDUIT
SECURITY CAMERA
GENERAL DETAIL NOTES:
CEILING MOUNTED SPEAKER
SINGLE REMOTE HEAD
1.
CHECK LENGTH OF SCREWS BEFORE ATTACHING
OUTLETS TO MILLWORK. VERIFY SCREWS ARE NOT
TOO LONG, SO AS NOT TO DAMAGE OTHER SIDE OF
CASHWRAP WHEN SCREWS ARE TIGHTENED.
2. JUNCTION BOXES IN CASHWRAP ARE TO COME
PREINSTALLED BY THE MILLWORK MANUFACTURER.
F6
SCALE:
EM/NL RECESSED CAN LIGHT
TS
CKT #2
CKT #1
DEVICE LOCATIONS
DOOR CONTACT
G
WALL SWITCH - NUMBER INDICATES 2, 3 OR 4
POLE; LETTER INDICATES FIXTURE(S) TO BE
CONTROLLED BY SWITCH
S
ACCESSIBLE
EXOTHERMIC
CONNECTION
MOTION DETECTOR
D
C
PUSHBUTTON
S
2
SEAL
QUAD RECEPTACLE
(TYP. OF 1)
BURGULAR SYSTEM PANEL
CHIME/BELL TRANSFORMER
S
C
TECH RACK
EFFECTIVELY
GROUNDED BUILDING
STEEL COLUMN
1
F
A
B
FRAME WARMER DUPLEX
RECEPTACLE 24 HOUR CIRCUIT #2
QUAD RECEPTACLE 24
HOUR CIRCUIT #1
(TYP. OF 2)
EQUIPMENT GROUND
DRY TYPE TRANSFORMER
D
H
M
3 BONDING JUMPER
1
NEUTRAL BAR
@ 48"
EQUIPMENT LOCATIONS
2 GROUNDING ELECTRODE
CONDUCTOR
CONDUIT GROUND
O
S
S
F
XX
WATER FLOW SWITCH
PS
BURG
CHIME/BELL
G
W
F
1 GROUNDED (NEUTRAL CONDUCTOR)
TELEPHONE OUTLET - FLOOR MOUNTED
H
SAFE SECURITY
TRANSFORMER GROUND DETAIL NOTES
@ 80"
ALARM HORN
V
D
TRASH
CPU
GROUND BAR
T
GROUND BAR
JUNCTION BOX
Mason, Ohio 45040
TECH RACK
@ 60"
120 VOLT DUPLEX RECEPTACLE FLOOR MOUNTED
J
14
SEE PLAN FOR CORRECT MONITOR
RIGHT HAND/LEFT HAND LOCATION.
FRAME WARMER
PHONE
TRANSFORMER (XFMR)
FACP
J
13
RECEIPT PRINTER
MONITOR
DRY-TYPE TRANSFORMER
GROUND DETAIL
F11
SCALE:
1 REGISTER
CASHWRAP ELEVATION
AT
CEILING MOUNTED EXIT SIGN
WALL MOUNTED EXIT SIGN
SINGLE PHASE MOTOR
E
THREE PHASE MOTOR
COMBINATION EMERGENCY AND EXIT LIGHT
EQUIPMENT DISCONNECT SWITCH
REMOTE EMERGENCY POWER PACK
MAGNETIC COMBINATION MOTOR STARTER OR
CONTACTOR DISCONNECT SWITCH
WALL MOUNTED EMERGENCY LIGHT
C
E
R
MAGNETIC STARTER OR CONTACTOR
MASTER LIGHTING SWITCH BANK
CEILING MOUNTED
EXISTING
RELOCATED
A-2
A-12
C2
GENERAL
SALES (a)
(SPST)
GENERAL
SALES (b)
(SPST)
DISPLAY &
DECORATIVE
LIGHTING (c)
(SPST)
USER: SHOLLAND
PLOTTED: 7/9/2015 - 1:26 PM
LAYOUT: E-501
NON-MAGNETIC MANUAL MOTOR STARTER
ABBREVIATIONS
A
D
AFC
AFF
AFG
AMP
ANSI
ARCH
ASHRAE
AWG
ABOVE FINISHED CEILING
ABOVE FINISHED FLOOR
ABOVE FINISHED GRADE
AMPERES
AMERICAN NAT'L STANDARDS INST.
ARCHITECT, ARCHITECTURAL
AMERICAN SOCIETY OF HEATING,
REFRIGERATION & AC ENGINEERS
AMERICAN WIRE GAUGE
B
C
BKR
BLDG
BMS
CONDUIT
CABLE TELEVISION SYSTEM
CLOSED CIRCUIT TELEVISION
CIRCUIT
CEILING
H
HTR
HVAC
HZ
HEATER
HEATING, VENTILATING & A/C
HERTZ
KVA
KW
KWH
KILOVOLT-AMPS
KILOWATTS
KILOWATT-HOUR
LOCKED ROTOR AMPS
LIGHTING
M
MAX
MCA
MCB
MH
MIN
MOCP
dB
DECIBEL
DIA (OR Ø) DIAMETER
DISC
DISCONNECT
DN
DOWN
DWG
DRAWING
DPST
DOUBLE POLE SINGLE THROW
MTD
MAXIMUM
MINIMUM CIRCUIT AMPACITY
MAIN CIRCUIT BREAKER
MANHOLE, METAL HALIDE
MINIMUM
MAXIMUM OVER CURRENT
PROTECTION
MOUNTED
N/A
NEC
NEMA
NFPA
NIC
N.O.
NTS
F
RELAY FOR MUSIC
SHUT-OFF
ON CENTER
OCCUPATIONAL SAFETY &HEALTH
ADMIN.
NOT APPLICABLE
NATIONAL ELECTRICAL CODE
NATIONAL ELECTRICAL MFR'S ASSOC.
NATIONAL FIRE PROTECTION ASSOC.
NOT IN CONTRACT
NORMALLY OPEN
NOT TO SCALE
PF
PH
PVC
D6
POWER FACTOR
PHASE
POLYVINYL CHLORIDE
SCALE:
NOT USED
R
RCP
REV
REX
RLA
RM
120V.
REFLECTED CEILING PLAN,
REVISION, REVISE
REMOVE EXISTING
RUNNING LOAD AMPS
ROOM
SF
SPST
V
VA
QUADRUPLEX
RECEPTACLE
THROUGH
TYPICAL
MONITOR
UNDERWRITERS LABORATORIES, INC.
UNLESS OTHERWISE NOTED
UNINTERRUPTABLE POWER SUPPLY
FIRE ALARM
FIRE ALARM CONTROL PANEL
FULL LOAD AMPS
FOOT, FEET
REFER TO ARCH DETAILS
ON SHEET A-502 AND
RESPONSIBILITY SCHEDULE
ON SHEET G-002 FOR
ADDITIONAL INFORMATION.
EXTEND CABLE TO PROPOSED HEAD END EQUIPMENT
LOCATION. PROVIDE ENOUGH EXCESS CABLE TO
REACH ANY WALL IN BACK ROOM. COIL AND MARK
CABLE AS CCTV. HEAD END EQUIPMENT LOCATION
MUST BE WITHIN 10' OF THE 'NETWORK SWITCH
ACCESS'.
2.
FOR CAMERAS, PROVIDE WHITE PLENUM RATED CAT
5E CABLING. COIL 5' OF CABLING AT EACH CAMERA
LOCATION FOR CONNECTIONS.
3.
PROVIDE RJ-45 CONNECTORS AT CAMERA LOCATIONS
ONLY. CONNECTORS NOT NEEDED AT THE HEAD END
EQUIPMENT LOCATION.
VOLT
VOLT-AMPERE
WATT
A6
SCALE:
ABBREVIATIONS AND SYMBOLS
1
2
3
4
5
C1
A-8
SPARE
A-15
SPARE
STOREFRONT SIGN
SHOW WINDOW RECEPTACLES
STOREFRONT TRACK LIGHTS
POWER CONTACTOR FROM CIRCUIT
A-41 THRU SWITCH 'c'
SEE SHEET E-101 FOR ACTUAL NUMBER OF DEVICES, AND ADDITIONAL NOTES.
ALL MATERIALS SHALL BE NEW AND BEAR UL LABELS.
SUPPLY SHOP DRAWINGS FOR FIRE ALARM SYSTEM TO LOCAL AUTHORITY FOR
APPROVAL PRIOR TO INSTALLATION.
4. FURNISH AND INSTALL ALL LABOR AND MATERIALS REQUIRED FOR A COMPLETE
INSTALLATION AS INDICATED.
5. ALL WORK SHALL COMPLY WITH THE REQUIREMENTS OF NEC, NFPA, STATE AND
LOCAL CODES.
CAMERA
(QUANTITY
ON PLAN)
1.
W
W
POWER CONTACTOR AND TC1 FROM CIRCUIT A-41
CONTACTOR CONTROLLED BY TIMECLOCK
REUSE EXISTING ANNUNCIATING DEVICES,
SEE SHEET E-101 FOR LOCATION AND QUANTITY.
REUSE EXISTING PULL STATION SEE
SHEET E-101 FOR LOCATION AND QUANTITY.
1.
2.
3.
3
SQUARE FEET, SQUARE FOOT
SINGLE POLE SINGLE THROW
U
UL
UON
UPS
F
1
T
THRU
TYP
V
EXISTING FIRE
ALARM PANEL.
SEE SHEET
E-101 FOR
LOCATION AND
ADDITIONAL
NOTES
2
DVD-R
S
A1
SCALE:
R
P
V
N
E
FA
FACP
FLA
FT
OC
OSHA
LRA
LTG
ETR
EXISTING TO REMAIN
EWC
ELECTRICAL WATER COOLER
EXH
EXHAUST
EX, EXIST EXISTING
A
G
GAS, GROUND
GC
GENERAL CONTRACTOR
GFI, GFCI GROUND FAULT INTERRUPTER
GRND
GROUND
L
D
B
O
K
BREAKER
BUILDING
BUILDING MANAGEMENT SYSTEM
C
C
CATV
CCTV
CKT
CLG
G
RIVERCHASE GALLERIA
1
1.
C2
UPON ALARM SIGNAL FROM ANY INITIATING DEVICE THE FIRE ALARM PANEL SHALL:
A. INITIATE AN ALARM SIGNAL AT TENANT'S FIRE ALARM PANEL.
B. SHUT DOWN TENANT'S HVAC SYSTEM (IF APPLICABLE)
C. INITIATE TENANT'S HORN/STROBES.
D. ACTIVATE THE TENANT ZONE SMOKE CONTROL EXHAUST SYSTEM.(IF APPLICABLE)
E. NOTIFY LOCAL FIRE DEPARTMENT OF FIRE EMERGENCY LOCATION.
F. SEND SIGNAL TO OWNERS SECURITY AND LOSS PREVENTION CENTRAL
MONITORING SYSTEM.
6
SGH STORE #: 4933
DRAWN BY: SRH
REVIEWED BY: RAP
AUTHORIZED FOR:
ELECTRICAL DETAILS
& ABBREVIATIONS
SCALE:
7
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
NOTES:
· ALL CONTACTORS ARE NORMALLY OPEN,
ELECTRICALLY HELD CLOSED, WITH THE
NUMBER OF POLES AS SHOWN.
· SUPPLY POWER TO CONTACTORS THRU
A-41 IN ALL CASES.
· LOCATE CONTACTORS AND TIME CLOCK
ADJACENT TO PANEL 'A'.
A8
CCTV SYSTEM
SALES TRACK LIGHTS
SALES TRACK LIGHTS
SALES AREA DISPLAY CASES
SALES AREA DISPLAY CASES
A-4
A-6
A-10
A-20
SPARE
SPARE
SPARE
SPARE
A12
SCALE:
FIRE ALARM SYSTEM
8
9
10
11
E- 501
LIGHTING CONTROL DIAGRAM
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Mason, Ohio 45040
K
DOUBLE NUT AND
SQUARE WASHERS.
TRANSFORMER
FASTEN UNISTRUT TO JOIST
CHORD ANGLE WITH P2785
UNISTRUT CLAMP (TYP. OF 8).
MECHANICAL EQUIPMENT FEEDER/CONNECTION SCHEDULE
J
H
FEEDERS
ITEM
VOLTAGE
HP
KW
M.C.A.
WIRE
COND
TYPE OF
CONN
EX IWH
120V
1PH
---
3.6
---
EXISTING
1"
EXSTING
EX VAV
480V
3PH
---
---
6
EXISTING
3/4"
THRU DISC.
SWITCH
DISC
SW
BRANCH
BREAKER
REMARKS
P2000 UNISTRUT FRAME
TO SPAN (2) JOISTS.
30A-1P
EXISTING
SEE
NOTE #1
15A-3P
SEAL
NOTE:
1. DISCONNECT IS FURNISHED WITH UNIT.
2. DISCONNECT IS TO BE FURNISHED AND INSTALLED BY ELECTRICAL CONTRACTOR
1/2" HANGER RODS
(TYP. OF 4).
VIBRATION ISOLATION
PADS (TYP. OF 4)
DOUBLE NUT HANGER ROD TO
SUPPORT UNISTRUT FRAME
AFTER EQUIPMENT IS LEVELED.
P2000 UNISTRUT FRAME
G
G5
SCALE:
EQUIPMENT SCHEDULES
TRANSFORMER
JOIST MOUNT
F
LEASE LINE
E
AT
TENANT
EXISTING 1 1/2" CONDUIT BACK TO LANDLORDS
ELECTRICAL ROOM. FIELD VERIFY PRIOR TO BID
USER: SHOLLAND
PLOTTED: 7/9/2015 - 12:55 PM
LAYOUT: E-601
CEILING
RELOCATED
XFMR
15KVA, 480V,
3PH PRIMARY,
208V/120Y
SECONDARY.
EXISTING TRANSFORMER
TO BE RELOCATED
ABOVE CEILING
EXISTING ELECTRICAL
SWITCHGEAR
D
C-1 C-2
ZONE ZONE
"SF"
"C"
TC
EXISTING
PANEL A
120/208V
3PH, 4W
60A MCB
#6 CU BOND TO
BUILDING STEEL
RIVERCHASE GALLERIA
G1
SCALE:
EXISTING
PANEL HP
277/480V
3PH, 4W
60A MCB
C
FINISH FLOOR
APPROX.
150'-0"
RIVERCHASE GALLERIA
1.
2.
3.
B
4.
5.
6.
7.
8.
9.
A
10.
HVAC CIRCUIT BREAKERS TO BE "HACR" TYPE WHERE REQUIRED BY EQUIPMENT NAMEPLATE PER N.E.C.
TENANTS ELECTRICAL CONTRACTOR SHALL FIELD VERIFY EXACT K.A.I.C. RATING OF LANDLORD'S DISTRIBUTION
EQUIPMENT. FURNISH AND INSTALL TENANTS ELECTRICAL SYSTEM TO MATCH.
ELECTRICAL CONTRACTOR SHALL BALANCE ALL PANELS AND ELECTRICAL EQUIPMENT, UNDER LOAD CONDITIONS,
TO ±7% BETWEEN PHASES: A/B, B/C, A/C REGARDLESS OF CIRCUITING INDICATED.
ELECTRICAL CONTRACTOR SHALL MAINTAIN PROPER CLEARANCE FOR ELECTRICAL EQUIPMENT PER N.E.C.
ARTICLE 110.26. FIELD VERIFY EXACT MOUNTING SPACE AVAILABLE IN ELECTRICAL ROOM/ AREA PRIOR TO
INSTALLATION OF ELECTRICAL EQUIPMENT.
ELECTRICAL CONTRACTOR SHALL MAKE ALL FINAL ELECTRICAL CONNECTIONS FOR A COMPLETE ELECTRICAL
DISTRIBUTION SYSTEM.
TENANT'S NAME AND SPACE SHALL BE ENGRAVED ON A BAKELITE PLATE WITH 1" HIGH LETTERS. SCREW FASTEN
TO THE METER SOCKET AND DISCONNECT SWITCH AT THE SERVICE DISTRIBUTION POINT.
ALL CONNECTIONS TO LANDLORD'S SERVICE EQUIPMENT SHALL BE AS DIRECTED BY LANDLORD'S SITE
REPRESENTATIVE. TENANT ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ALL TERMINATION EXPENSES.
SYSTEM SHALL BE GROUNDED TO THE MAIN BUILDING'S GROUNDING SYSTEM.
ELECTRICAL CONTRACTOR SHALL INCLUDE IN BID ALL WORK AND MODIFICATIONS REQUIRED TO COMPLY WITH
LANDLORDS TENANT CRITERIA, ENERGY CODES, NATIONAL, STATE AND LOCAL CODES.
ALL EQUIPMENT TO BE SUPPLIED & INSTALLED PER RESPONSIBILITY SCHEDULE AS SHOWN ON THIS SHEET.
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #: 4933
DRAWN BY: SRH
REVIEWED BY: RAP
AUTHORIZED FOR:
ELECTRICAL SINGLE LINE
DIAGRAM AND PANEL
SCHEDULES
A1
SCALE:
A9
SCALE:
ELECTRICAL SINGLE LINE DIAGRAM
1
2
3
4
5
6
7
8
E-601
PANEL SCHEDULES AND LOAD SUMMARY
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
26 05 29 DISTRIBUTION
M. ALL PERMITS REQUIRED BY LAWS, ORDINANCES AND BUILDING CODES HAVING JURISDICTION SHALL
AH. MANUFACTURER'S CATALOG CUTS MAY BE SUBMITTED FOR STANDARD CATALOG LIGHTING
BE OBTAINED AT PROPER TIME BY AND AT THE EXPENSE OF THE ELECTRICAL CONTRACTOR.
FIXTURES AND OTHER EQUIPMENT. CATALOG CUTS MAY BE MARKED UP TO MEET THE PROJECTA. GENERAL CONTRACTOR SHALL FURNISH ALL LABOR, MISC. MATERIALS AND EQUIPMENT
SPECIFICATIONS. CUTS SHALL BE MARKED TO INDICATE MODEL NUMBER, SIZE, TYPE, COLOR,
THE FOLLOWING TERMS SHALL APPLY TO ALL WORK DONE UNDER THIS CONTRACT:
NECESSARY TO INSTALL ALL OF THE ELECTRICAL SERVICE FROM THE LANDLORD'S ELECTRICAL
N. ALL ELECTRICAL WORK SHALL BE INSPECTED BY THE GOVERNMENTAL AGENCY HAVING
RATING, ETC., OF THE ITEM TO BE FURNISHED.
SERVICE ROOM INCLUDING (AS INDICATED ON SHEET E4.0) BUT NOT LIMITED TO THE SECONDARY
1. ANY REFERENCE TO TENANT OR TENANT'S CONSTRUCTION MANAGER OR FURNISHED BY ANY JURISDICTION, INCLUDING LOCAL INSPECTION AUTHORITIES.
CABLES, CONDUIT, PULL WIRE AND GROUND ROD AND SLEEVE AS REQUIRED. COORDINATE
AI. PROVIDE INSTRUCTION TO TENANT'S OPERATING PERSONNEL AS NECESSARY, SHOWING LOCATIONSREQUIREMENTS WITH LANDLORD PRIOR TO BID. THE GENERAL CONTRACTOR SHALL COORDINATE
OF THE ABOVE REFERS TO SUNGLASS HUT.
O. WHERE TRADE NAMES AND MANUFACTURERS ARE USED ON THE DRAWINGS OR IN THE
AND PROPER OPERATION OF MAJOR ITEMS OF EQUIPMENT AND SYSTEM COMPONENTS AND
2. DRAWINGS AND GENERAL PROVISIONS OF CONTRACT, INCLUDING GENERAL AND
INSTALLATION OF THE DISCONNECT SWITCHES AND PANELBOARD WITH THIS WORK.
REFERRING TO THE OPERATING INSTRUCTION MANUAL DESCRIBED BELOW AS A GUIDE.
SUPPLEMENTARY CONDITIONS AND ALL OTHER SPECIFICATIONS SECTIONS, APPLY TO THIS SPECIFICATIONS, THE EXACT EQUIPMENT SHALL BE USED AS A MINIMUM FOR THE BASE BID.
MANUFACTURERS CONSIDERED AS AN EQUAL OR BETTER IN ALL ASPECTS TO THAT SPECIFIED WILL
AND THE OTHER SECTIONS OF DIVISION 26 THROUGH 28.
B. ALL CONDUCTORS SHALL BE COPPER. ALUMINUM CONDUCTORS AREPERMITTED.
3. THE CONTRACTOR FOR THIS WORK IS REQUIRED TO READ THE SPECIFICATIONS AND REVIEW BE SUBJECT TO APPROVAL IN WRITING, THROUGH SHOP DRAWING SUBMITTAL PROCESS, BY AJ. GENERAL CONTRACTOR SHALL GUARANTEE THIS WORKMANSHIP AND MATERIALS, EXCEPT FOR
TENANT-SUPPLIED MATERIALS, FOR A PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE C.
(IN COORDINATE WORK PROVIDED BY LANDLORD PRIOR TO BID AND INCLUDE THE COST OF ANY
DRAWINGS FOR ALL DIVISIONS OF WORK AND IS RESPONSIBLE FOR THE COORDINATION OF TENANT'S CONSTRUCTION MANAGER PRIOR TO ACCEPTANCE. THE USE OF ANY UNAUTHORIZED
THIS WORK AND THE WORK OF THE SUBCONTRACTORS WITH ALL DIVISIONS OF WORK. IT IS EQUIPMENT SHALL BE SUBJECT TO REMOVAL AND REPLACEMENT AT THE CONTRACTOR'S EXPENSE.WRITING) OF THE INSTALLATION BY TENANT'S CONSTRUCTION MANAGER/ENGINEERING MANAGER SUCH WORK AS DIRECTED BY LANDLORD. WIRING OF METERING EQUIPMENT SHALL BE BY GENER
AND LEAVE THIS WORK IN PERFECT ORDER AT COMPLETION.
THIS CONTRACTOR'S RESPONSIBILITY TO PROVIDE THE SUBCONTRACTORS WITH A COMPLETE
CONTRACTOR AS DIRECTED BY THE ELECTRIC COMPANY.
P. GENERAL CONTRACTOR SHALL SUBMIT ONLY SUBSTITUTION REQUESTS TO TENANT'S
SET OF BID DOCUMENTS.
4. THIS CONTRACTOR IS RESPONSIBLE FOR SCHEDULING THE COMPLETION AND INSPECTION OFCONSTRUCTION MANAGER FOR APPROVAL. SUBMISSIONS SHALL BE MADE EARLY ENOUGH IN AK. SHOULD DEFECTS DEVELOP WITHIN GUARANTEE PERIOD, GENERAL CONTRACTOR SHALL, UPOND. METERING EQUIPMENT SHALL BE FURNISHED BY GENERAL CONTRACTOR AND INSTALLED TO THE
PROJECT TO ALLOW SEVEN (7) WORKING DAYS FOR TENANT'S CONSTRUCTION MANAGER'S REVIEWNOTICE OF SAME, REMEDY SUCH DEFECTS AND HAVE DAMAGES TO OTHER WORK OR FURNISHINGS MALL'S REQUIREMENTS.
THIS WORK AND THE WORK OF THE SUBCONTRACTORS TO COMPLY WITH THE OWNER'S
WITHOUT CAUSING DELAYS OR CONFLICTS TO THE JOB'S PROGRESS. SUBMITTALS SHALL BEAR THECAUSED BY DEFECTS OR WORK OR CORRECTIONS TO SAME REPAIRED AND/OR REPLACED AT THIS
SCHEDULE AND THE PROJECT COMPLETION DATE.
STAMP OF THE GENERAL CONTRACTOR AND/OR SUB-CONTRACTOR SHOWING THAT THEY HAVE
CONTRACTOR'S EXPENSE TO CONDITION BEFORE SUCH DEFECTS OR DAMAGE.
5. THIS CONTRACTOR SHALL VISIT THE SITE PRIOR TO SUBMITTAL OF BID TO DETERMINE
E. DISCONNECT SWITCHES SHALL BE HEAVY-DUTY TYPE, UL LISTED.
REVIEWED AND CONFIRMED THAT THE SUBMITTALS ARE IN CONFORMANCE WITH THE CONTRACT
CONDITIONS AFFECTING THE WORK. ANY ITEMS WHICH ARE NOT COVERED IN THE BID
DRAWINGS AND SPECIFICATIONS OR INDICATE WHERE EXCEPTIONS HAVE BEEN TAKEN.
AL. COMPILE TWO (2) WRITTEN MANUALS OF OPERATING INSTRUCTIONS INCLUDING COPIES OF SHOP
DOCUMENTS OR ANY PROPOSED SUBSTITUTIONS SHALL BE LISTED SEPARATELY AND
F. DISCONNECT SWITCHES SHALL BE BY SQUARE D, GENERAL ELECTRIC, SIEMENS, OR CUTLER
DRAWINGS AND A LISTING OF EQUIPMENT SUPPLIERS.MATERIAL SHALL BE AS FOLLOWS:
QUALIFIED IN THE CONTRACTOR'S BID. SUBMITTAL OF BID SHALL SERVE AS EVIDENCE OF
HAMMER.
Q.
FOR
ANY
PHASED
STORE
CONSTRUCTION,
THIS
CONTRACTOR
IS
TO
INCLUDE
IN
THIS
BID
ALL
KNOWLEDGE OF EXISTING CONDITIONS AND ANY MODIFICATIONS WHICH ARE REQUIRED TO
MEET THE INTENT OF THE DRAWINGS AND SPECIFICATIONS. FAILURE TO VISIT THE SITE DOES NECESSARY ELECTRICAL SERVICE CHANGES REQUIRED TO KEEP THE OPERATING PHASE OF THE 1. LIST OF MAJOR EQUIPMENT USED IN PROJECT ACCOMPANIED BY CONTRACTOR PURCHASEG. ALL SWITCHES SHALL HAVE SWITCH BLADES WHICH ARE FULLY VISIBLE IN THE "OFF" POSITION
ORDER NUMBERS AND SUPPLIERS' NAMES AND ADDRESSES.
STORE'S ELECTRIC SERVICE IN OPERATION. CONTRACTOR MUST SCHEDULE WITH TENANT'S
NOT RELIEVE THE CONTRACTOR OF RESPONSIBILITY IN PERFORMANCE OF WORK.
WHEN THE SWITCH DOOR IS OPEN. SWITCHES SHALL HAVE REMOVABLE ARC SUPPRESSORS
6. REFER TO RESPONSIBILITY SCHEDULE ON THE ARCHITECTURAL DRAWINGS FOR INFORMATIONCONSTRUCTION MANAGER AND LANDLORD (IN WRITING) ONE WEEK PRIOR TO ANY SHUT DOWN OF 2. ONE COPY OF EACH SHOP DRAWING GROUPED BY TYPES OF EQUIPMENT, I.E., LIGHTING
WHERE NECESSARY TO PERMIT EASY ACCESS TO LINE SIDE LUGS. LUGS SHALL BE FRONT
THE P.O.S., CASH REGISTERS, ELECTRICAL, TELEPHONE OR FIRE ALARM SYSTEMS. ADVISE GENERAL
FIXTURES, PANELBOARDS, ETC.
IN REGARD TO RESPONSIBILITY OF WORK OR ITEMS WHICH MAY AFFECT BID.
REMOVABLE AND UL LISTED FOR 75 DEGREES C., ALUMINUM OR COPPER WIRES.
CONTRACTOR AND TENANT AT TIME OF BID IF ANY CONFLICTS EXIST.
3. SECTION FOR EACH SYSTEM, INCLUDING:
a. BRIEF DESCRIPTION OF SYSTEM OPERATION WITH LOCATION OF MAJOR COMPONENTS. H. SWITCHES SHALL BE QUICK-MAKE, QUICK-BREAK. THE OPERATING HANDLE SHALL BE AN INTEGRA
PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR REQUIRED TO INSTALL NEW
b. LIST OF ITEMS IN SYSTEM REQUIRING PERIODIC SERVICE. REQUIRES SEPARATE SECTION
COMPLETE ELECTRICAL SYSTEM AS INDICATED ON DRAWINGS, AS REQUIRED BY CODE AND AS R. GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR THE COORDINATION OF THE DEMOLITION OF
PART OF THE BOX, NOT THE COVER. PROVISIONS FOR PADLOCKING THE SWITCH IN THE "OFF"
EXISTING WORK. COORDINATE ANY EXISTING EQUIPMENT TO BE LEFT INTACT AND ADVISE TENANT'S
FOR EACH OF: ELECTRICAL DISTRIBUTION SYSTEM FROM THE SERVICE ENTRANCE TO EACH POSITION WITH AT LEAST THREE LOCKS SHALL BE PROVIDED. SWITCHES SHALL HAVE A DUAL
SPECIFIED HEREIN, IN DIVISIONS 26, 27, AND 28. WORK SHALL INCLUDE, BUT NOT BE LIMITED TO,
CONSTRUCTION MANAGER AT TIME OF BID.
LIGHTING AND POWER PANEL AND OTHER SYSTEMS (I.E. CONTROL SYSTEMS AND ANY OTHER COVER INTERLOCK TO PREVENT UNAUTHORIZED OPENING OF THE SWITCH DOOR WHEN THE
THE FOLLOWING:
GENERAL CONTRACTOR SYSTEM LISTED IN THESE SPECIFICATIONS.)
HANDLE IS IN THE "ON" POSITION, AND TO PREVENT CLOSING OF THE SWITCH MECHANISM WITH
S. ELECTRICAL CONTRACTOR SHALL INCLUDE, AND WILL BE HELD RESPONSIBLE FOR, THE REMOVAL OF
1. TEMPORARY SERVICE AS REQUIRED.
THE DOOR OPEN. THE HANDLE POSITION SHALL INDICATE WHETHER THE SWITCH IS "ON" OR "OFF
ALL EXISTING CONDUIT, FIRE ALARM SYSTEM, SWITCH GEAR, PITCH POCKETS AND EQUIPMENT,AM.
ETC.
OWNER'S SHALL PROVIDE A COMPLETE 12-MONTH WARRANTY FOR ALL PARTS ON EQUIPMENT
2. PRIMARY DISTRIBUTION BY ELECTRIC COMPANY.
UNLESS SPECIFICALLY NOTED OTHERWISE. CONTRACTOR MUST VERIFY WITH THE LANDLORD ALL PROVIDED BY TENANT AND TENANT'S VENDORS. THIS CONTRACTOR SHALL NOT BEAR ADDITIONAL
3. EMERGENCY AND EXIT LIGHTING SYSTEMS.
I.
SWITCHES SHALL BE FURNISHED IN NEMA 1 GENERAL PURPOSE ENCLOSURE EXCEPT ALL
WARRANTIES BEYOND A COMPLETE WORKING SYSTEM, AND AS SUCH, NO ADDITIONAL MONIES
4. CONDUIT AND CABLES FOR TELEPHONE AND DATA SYSTEMS AS SHOWN ON THE DRAWINGS. PRESUMED ABANDONED EQUIPMENT, CONDUIT AND SWITCH GEAR PRIOR TO REMOVAL. PITCH
SWITCHES LOCATED OUTDOORS SHALL BE NEMA 3R WEATHERPROOF (WP). NEMA 3R ENCLOSURE
POCKETS SHALL BE REMOVED AND THE ROOF PATCHED, AS REQUIRED BY THE LANDLORD. ALL
SHOULD BE INCLUDED IN THE BID.
5. ELECTRICAL PANEL AND BRANCH CIRCUIT WIRING.
SHALL BE MANUFACTURED FROM GALVANIZED STEEL. ENCLOSURES SHALL HAVE A GRAY BAKED
EXTRANEOUS ITEMS IN THE SPACE OR ON THE ROOF NOT APPLICABLE TO THE NEW WORK MUST BE
6. WIRING DEVICES AND PLATES.
ENAMEL FINISH, ELECTRODEPOSITED, ON CLEANED, PHOSPHATIZED STEEL.
REMOVED AND ROOF/WALL/FLOOR PATCHED/REPAIRED TO LIKE NEW CONDITION. EXISTING
AN. AT THE END OF THE PROJECT, THIS CONTRACTOR SHALL CLEAN ALL EQUIPMENT, INCLUDING LIGHT
7. LIGHTING FIXTURES AND LAMPS, INSTALLATION AND WIRING.
ABANDONED CONDUIT OR EQUIPMENT IN THE FLOOR, EMBEDDED IN CONCRETE, OR OTHERWISE FIXTURES, TO THE SATISFACTION OF OWNER'S. ALL DUST, DIRT, DEBRIS, PAINT AND FOREIGN J.
8. LIGHTING CONTROLS.
SWITCHES SHALL BE RATED FOR AC. FUSIBLE SWITCHES MUST ACCEPT CLASS R FUSES AND HAV
INACCESSIBLE, ARE TO BE CUT OFF AND SEALED BELOW OR WITHIN FLOOR OR WALL LEVEL WHEN MATTER SHALL BE REMOVED FROM ALL EQUIPMENT.
9. ELECTRICAL CONNECTIONS TO EQUIPMENT FURNISHED BY OTHERS, SIGNS, CORNICE
PROVISIONS TO REJECT ALL FUSES EXCEPT CLASS R. THE UL LISTED SHORT CIRCUIT RATING OF
THEY ARE NOT TO BE REUSED IN THIS PROJECT. IF REQUIRED BY LANDLORD OR CODES,
LIGHTING, CASE LIGHTING, ETC., AS SHOWN ON DRAWINGS.
THE SWITCHES SHALL BE 200,000 RMS SYMMETRICAL AMPERES WHEN CLASS R FUSES ARE
ABANDONED CONDUIT MUST BE REMOVED TO POINT OF ORIGIN. CONFIRM EXTENT OF DEMOLITION
10. INSTALLATION OF CONDUIT AND CABLES FOR SOUND SYSTEM AS SHOWN ON DRAWINGS.
USED.
26 05 19 LOW VOLTAGE ELECTRICAL POWER CONDUCTORS
PRIOR TO BID AND INCLUDE IN PROPOSAL.
11. SMOKE/FIRE ALARM WIRING, DEVICES AND CONDUIT, AS SHOWN OR DESCRIBED ON
A. CONDUCTORS SHALL BE COPPER, 90°C TYPE THHN OR THWN UNLESS NOTED OTHERWISE ON THE
DRAWINGS OR AS NECESSARY TO MEET LANDLORD, STATE, LOCAL, INSURANCE AND FIRE
K. NAMEPLATES SHALL INDICATE FUNCTION OF EACH DEVICE. NAMEPLATES SHALL BE LAMINATED
T. GENERAL CONTRACTOR SHALL PROVIDE SLEEVES TO PROTECT EQUIPMENT OR FACILITIES IN THE DRAWINGS, THE MINIMUM COPPER WIRE SIZES FOR WET AND DRY AREAS AS DEFINED BY THE
DEPARTMENT REQUIREMENTS.
PHENOLIC WITH A WHITE SURFACE AND BLACK CORE. USE 1/16" THICK MATERIAL FOR
12. INSTALLATION OF CONDUITS STUBBED TO ABOVE CEILING FOR HVAC. ALSO, ANY ADDITIONAL INSTALLATION. EACH SLEEVE SHALL EXTEND THROUGH IT'S RESPECTIVE FLOOR, WALL OR PARTITIONN.E.C. SHALL BE AS FOLLOWS:
NAMEPLATES UP TO 2"X4" AND USE 1/8" THICK MATERIAL FOR LARGER SIZES. ALL NAMEPLATES
AND SHALL BE CUT FLUSH WITH EACH SURFACE EXCEPT SLEEVES THAT PENETRATE THE FLOOR,
CONDUIT FOR HVAC CONTROL EQUIPMENT WHERE PLENUM RATED CABLES ARE NOT
SHALL BE FURNISHED AND INSTALLED BY GENERAL CONTRACTOR. GENERAL CONTRACTOR TO
WHICH SHALL EXTEND 2" ABOVE THE FLOOR.
20 AMP CKT BKR OR FUSE = #12 AWG, THHN/THWN
PERMITTED.
COORDINATE WITH THE LOCAL BUILDING AUTHORITY OR BUILDING INSPECTOR ON WHICH ITEMS
13. THE GENERAL CONTRACTOR SHALL PAY FOR ALL ELECTRICITY PRIOR TO STORE
SHOULD HAVE A NAMEPLATE.
U. ALL SLEEVES AND OPENINGS THROUGH FIRE RATED WALLS AND/OR FLOORS SHALL BE FIRE SEALED 40 AMP CKT BKR OR FUSE = #8 AWG, THHN/THWN
MERCHANDISING, AND INCLUDE COST IN BID.
WITH CALCIUM SILICATE, SILICONE "RTV" FOAM, "3M" FIRE RATED SEALANTS OR EQUAL, SO AS TO
L.
ALL FUSES SHALL BE UL LISTED, CURRENT-LIMITING TYPE, MINIMUM 200,000 AMPS
RETAIN THEIR FIRE RATING.
WORK WHICH SHALL BE PERFORMED BY OTHERS, UNLESS NOTED OTHERWISE, INCLUDES THE
INTERRUPTING CAPACITY.
FOLLOWING:
V. SLEEVES IN BEARING AND MASONRY WALLS, FLOORS AND PARTITIONS SHALL BE STANDARD WEIGHT 200 AMP CKT BKR OR FUSE = #3/0 AWG, THHN/THWN
M. FUSES 1 AMP AND ABOVE SHALL BE BUSSMANN "LOW PEAK" RK-1. 250 VOLT FUSES SHALL BE
STEEL PIPE FINISHED WITH SMOOTH EDGES. FOR OTHER THAN MASONRY PARTITIONS, THROUGH
1. TEMPERATURE CONTROL WIRING THAT IS FURNISHED BY OTHERS PRE-WIRED IN UNITS.
USED ON 208/120 VOLT SYSTEMS. 600 VOLT FUSES SHALL BE USED ON 480/277 VOLT
SUSPENDED CEILINGS, OR FOR CONCEALED VERTICAL CONDUIT, SLEEVES SHALL BE 22 U.S.G. B. MINIMUM WIRE SIZES FOR 20A BRANCH CIRCUITS SHALL BE ADJUSTED FOR DISTANCE,
2. TELEPHONES AND FINAL CONNECTION OF WIRING THERETO.
SYSTEMS.
GALVANIZED STEEL MINIMUM.
MEASURED FROM THE PANELBOARD CIRCUIT BREAKER TO THE FURTHEST OUTLET,
3. INTERNAL WIRING OF EQUIPMENT FURNISHED AND PRE-WIRED BY OTHERS.
AS FOLLOWS:
4. SECURITY SYSTEM FURNISHED AND INSTALLED BY SECURITY CONTRACTOR (IF REQUIRED).
N. CONTROL FUSES FOR MOTOR STARTERS, CONTACTORS, AND CONTROL PANEL TRANSFORMERS
W. HANGERS SHALL INCLUDE ALL MISCELLANEOUS STEEL SUCH AS ANGLE IRON, WIRE, UNISTRUT,
LESS THAN 100 FT - #12
SHALL BE BUSSMANN FNQ-R SIZED AT 500% RATED CURRENT.
C-CLAMPS WITH RETAINING CLIPS, CHANNELS, HANGER RODS, ETC., NECESSARY FOR THE
BETWEEN 101 AND 150 FEET - #10
ELECTRICAL EQUIPMENT FURNISHED BY OTHER TRADES OR BY TENANT AND SPECIFIED IN OR SHOWN
BETWEEN 151 AND 250 FEET - #8
ON CONTRACT DOCUMENTS SHALL BE INSTALLED AND CONNECTED BY GENERAL CONTRACTOR, INSTALLATION OF WORK.
O. FURNISH SPARE FUSES TO THE TENANT IN THE FOLLOWING QUANTITIES: 10% OF TOTAL PROJECT
OVER 251 FEET - #6
EXCEPT AS OTHERWISE NOTED. PROVIDE BRANCH CIRCUIT CONNECTIONS TO ELECTRICALLY
QUANTITY (BUT NOT LESS THAN THREE (3) FOR EACH TYPE AND RATING OF FUSES).
OPERATED EQUIPMENT FURNISHED BY OTHERS AS SPECIFIED IN OR SHOWN ON THE CONTRACTX. HANGERS, SUPPORTS OR FASTENINGS SHALL BE PROVIDED AT EACH ELBOW, AT THE ENDS OF
STRAIGHT RUNS TERMINATING AT BOXES OR CABINETS, AND AT INTERMEDIATE POINTS AS
C. CONDUCTORS USED FOR EMERGENCY LIGHTING CIRCUITS SHALL BE #10 AWG, MINIMUM,
DOCUMENTS. TEMPORARY WIRING FOR OTHER CONTRACTORS SHALL BE INSTALLED BY THE
P. TYPED LIST OF ALL SPARES SHALL ALSO BE INCLUDED.
ELECTRICAL CONTRACTOR WHO SHALL BE ENTIRELY RESPONSIBLE TO THE TENANT FOR THE SAFE REQUIRED BY CODE. HANGERS SHALL BE FASTENED TO BUILDING STEEL, CONCRETE, OR MASONRY, AND SHALL BE RUN IN SEPARATE CONDUIT USED FOR NO OTHER PURPOSE.
BUT NOT TO OTHER CONDUIT OR PIPING. HANGERS UPPER ATTACHMENT MUST BE SUPPORTED
AND SATISFACTORY OPERATION OF SAID TEMPORARY WIRING. CONTRACTOR REQUIRING SUCH
Q. EXISTING PANELBOARDS TO REMAIN.
FROM THE TOP OF THE BAR JOIST. HANGING FROM METAL DECK IS NOT PERMITTED. WHERE
D. CONDUCTORS MAY BE STRANDED FOR SIZES #10 AWG AND LARGER. CONDUCTORS SIZE
TEMPORARY WIRING SHALL PAY FOR ALL DAMAGE TO PROPERTY RESULTING FROM ITS USE. COMPLY
INTERFERENCES OCCUR, IN ORDER TO SUPPORT CONDUIT, THE CONTRACTOR MUST INSTALL
#12 AND SMALLER SHALL BE SOLID (NOT STRANDED).
WITH LATEST REQUIREMENTS OF OCCUPATIONAL SAFETY AND HEALTH ACT (OSHA). PROVIDE
R. ALL PANELBOARDS ARE EXISTING TO REMAIN. SHALL BE LISTED UNDER UL 67 AND SHALL HAVE
PERSONNEL GROUND FAULT PROTECTION ON ALL TEMPORARY POWER AND LIGHTING CIRCUITS 30 TRAPEZE TYPE HANGERS OR SUPPORTS WHICH SHALL BE LOCATED WHERE THEY DO NOT INTERFERE
APPROPRIATE LABELING. ALL BUSSING SHALL BE SOLID COPPER.
WITH
ACCESS
TO
FIRE
DAMPERS,
VALVES,
JUNCTION
BOXES,
ACCESS
DOORS,
OTHER
EQUIPMENT
E.
ON
ALL
20
AMP
BRANCH
CIRCUITS,
CONDUCTORS
LARGER
THAN
#10
AWG
SHALL
BE
REDUCED
TO
AMPERES OR LESS. GROUND FAULT CIRCUIT INTERRUPTERS ON CONSTRUCTION CIRCUITS ARE NOT
REQUIRED WHERE CIRCUIT IS A PERMANENT CIRCUIT TO BE A PART OF THE COMPLETED BUILDING. SERVICE REQUIREMENTS AND/OR OTHER TRADES. HANGER TYPES AND INSTALLATION METHODS ARE#10 AWG WITHIN 10 FEET OF PANELBOARD AND DEVICES IN JUNCTION BOXES ON RATED
S. PANELBOARDS FOR USE ON 480Y/277V SYSTEM SHALL HAVE A MINIMUM INTEGRATED
SUBJECT TO LANDLORD CRITERIA.
TERMINAL STRIPS.
HOWEVER, CONTRACTOR SHALL PROVIDE APPROVED CORD SETS INCORPORATING GFCI
EQUIPMENT SHORT CIRCUIT CURRENT RATING OF 14,000 AMPS RMS SYMMETRICAL.
PROTECTION FOR PERSONNEL. SEE THE LOCALLY ADOPTED EDITION OF THE N.E.C. ALL FINISH
PANELBOARDS FOR USE ON 208Y/120V VOLT SYSTEM SHALL HAVE A MINIMUM INTEGRATED
Y. FIXTURE SUPPORTS SHALL BE IN ACCORDANCE WITH NEC ARTICLE 410.30 OR ANY LOCAL CODESF.
ALUMINUM CONDUCTORS ARE PERMITTED.
PAINTING IS TO BE PERFORMED BY GENERAL CONTRACTOR EXCEPT THAT THIS CONTRACTOR SHALL
EQUIPMENT SHORT CIRCUIT CURRENT RATING OF 10,000 AMPS RMS SYMMETRICAL. EXACT
RESTORE TO ORIGINAL CONDITION ANY PAINTING DEFACED BY THIS CONTRACTOR AFTER ORIGINALTHAT MAY APPLY.
RATING SHALL BE DETERMINED BY AVAILABLE FAULT CURRENT FROM UTILITY. GENERAL
G. THE FOLLOWING COLOR CODE SHALL BE USED:
PAINTING.
CONTRACTOR SHALL FURNISH PANELS BASED ON UTILITY COMPANY INFORMATION. ALL LUG
Z. UPON COMPLETION OF THE WORK, GENERAL CONTRACTOR SHALL FURNISH TO THE ARCHITECT A
CONNECTIONS SHALL BE 75 DEGREES C RATED.
CERTIFICATE OF INSPECTION AND APPROVAL FROM THE ABOVE DEPARTMENT BEFORE FINAL
PHASE
A
BLACK
BROWN
ELECTRICAL CONTRACTOR SHALL DO ALL CUTTING, CHASING, OR CHANNELING AND PATCHING
PAYMENT ON CONTRACT WILL BE ALLOWED.
PHASE B
RED
ORANGE
REQUIRED FOR ANY WORK UNDER THIS DIVISION. CUTTING SHALL HAVE PRIOR APPROVAL BY
T. PANELBOARD FRONT ASSEMBLY SHALL INCLUDE A HINGED DOOR WITH A FLUSH MOUNTED
PHASE C
BLUE
YELLOW
TENANT'S CONSTRUCTION MANAGER AND THE LANDLORD. PATCHING IS TO BE "AS NEW CONDITION".
CYLINDER LOCK TYPE SPRING LOADED LATCH. ALL LOCKS SHALL BE KEYED ALIKE. DOOR SHALL
AA. TEST ALL WIRING AND CONNECTIONS FOR CONTINUITY AND GROUNDS BEFORE ANY EQUIPMENT IS
NEUTRAL
WHITE
GRAY
INCLUDE
A TYPED CIRCUIT DIRECTORY CARD MOUNTED IN A FRAME WITH A CLEAR PLASTIC
CONNECTED. WHEN DIRECTED BY ARCHITECT, DEMONSTRATE BY PROPER VOLTAGE MEGGER TEST GROUND
GREEN
GREEN
ALL ELECTRICAL WORK SHALL BE INSTALLED SO AS TO BE READILY ACCESSIBLE FOR OPERATING, OF INSULATION RESISTANCE OF ANY CONDUCTORS AND REPLACE ALL CONDUCTORS WHICH FAIL
PROTECTIVE COVER.
ISOLATED GROUND
GREEN/ YELLOW STRIPE GREEN/YELLOW STRIPE
SERVICING, MAINTAINING AND REPAIRING. THIS CONTRACTOR IS RESPONSIBLE FOR PROVIDING
SAID TESTS UNTIL ALL CONDUCTORS ARE FREE FROM INSULATION FAULTS.
SUFFICIENT SERVICE ACCESS TO ALL EQUIPMENT.
U. EACH PANELBOARD SHALL HAVE A FULL CAPACITY SOLID COPPER NEUTRAL SUBASSEMBLY.
H. CIRCUIT BREAKER/FUSE AND WIRE SIZE COMBINATIONS NOT SHOWN ABOVE SHALL BE APPROVED
AB. ELECTRICAL LAYOUTS ARE SCHEMATIC. THE FINAL LOCATIONS OF ALL EQUIPMENT, OUTLETS, ETC.
BY THE ENGINEER PRIOR TO INSTALLATION.
ANY ACCESS PANELS REQUIRED, BUT NOT SPECIFIED OR SHOWN ON DRAWINGS, SHALL BE
V. EACH PANELBOARD SHALL INCLUDE A SOLID COPPER GROUND BUS SUBASSEMBLY, SIMILAR IN
SHALL BE SUBJECT TO REASONABLE CHANGES IN LOCATION UP TO THE TIME OF ROUGHING-IN AT
FURNISHED BY GENERAL CONTRACTOR WITH DESIGN TO BE APPROVED BY ARCHITECT BEFORE
CONSTRUCTION TO THE NEUTRAL SUBASSEMBLY, FACTORY MOUNTED AND BONDED TO THE BOX.
NO ADDITIONAL COST TO THE OWNER. EXACT LOCATIONS ARE DETERMINED BY EXACT LOCATION OF
26 05 26 GROUNDING AND BONDING
STARTING INSTALLATION.
EQUIPMENT, AND MAY BE REVISED TO SUIT THE CONSTRUCTION CONDITIONS AND COORDINATION
W. EACH PANELBOARD SHALL INCLUDE (WHERE SPECIFIED) A SOLID COPPER ISOLATED GROUND BUS
WITH OTHER TRADES. WHERE DRAWINGS, EXISTING SITE CONDITIONS, SPECIFICATIONS OR OTHER
THE DRAWINGS AND SPECIFICATIONS ARE INTENDED TO SUPPLEMENT EACH OTHER AND ANY
SUBASSEMBLY, SIMILAR IN CONSTRUCTION TO THE NEUTRAL SUBASSEMBLY, FACTORY SUPPLIED
TRADES CONFLICT OR ARE UNCLEAR, ADVISE THE GENERAL CONTRACTOR IN WRITING PRIOR TOA. FURNISH AND INSTALL A COMPLETE GROUNDING SYSTEM IN COMPLIANCE WITH ALL
REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE.
MATERIAL OR LABOR CALLED FOR IN ONE SHALL BE PROVIDED EVEN THOUGH NOT SPECIFICALLY SUBMITTAL OF BID. THE GENERAL CONTRACTOR IS RESPONSIBLE TO ADVISE TENANT'S
FIELD INSTALLED.
MENTIONED IN BOTH. ANY MATERIAL OR LABOR WHICH IS NEITHER SHOWN ON THE DRAWINGS NORCONSTRUCTION MANAGER IN WRITING OF ANY VARIATIONS TO CONTRACT DOCUMENTS PRIOR TO
B. A SEPARATE EQUIPMENT GROUNDING CONDUCTOR, MINIMUM SIZE PER NEC TABLE 250.122, X. INTERIOR LABELING SHALL INCLUDE A CONNECTION DIAGRAM AND LABELS INDICATING PROPER
CALLED FOR IN THE SPECIFICATIONS, BUT WHICH IS NECESSARY TO COMPLETE THE WORK OR
SUBMISSION OF THE BID. OTHERWISE, TENANT'S CONSTRUCTION MANAGER'S INTERPRETATION OF SHALL BE INSTALLED IN CONDUIT ALONG WITH ALL FEEDERS, BRANCH CIRCUITS AND CONTROL
WHICH IS USUALLY INCLUDED IN WORK OF SIMILAR CHARACTER, SHALL BE PROVIDED AS PART OF CONTRACT DOCUMENTS OR CONDITIONS SHALL BE FINAL WITH NO ADDITIONAL COMPENSATION.
TORQUE AND WIRE TYPES FOR MAIN INPUT CONNECTIONS AND BOTH LINE AND LOAD SIDE
CIRCUITS. CONDUCTOR INSULATION SHALL BE GREEN.
CONTRACT.
CIRCUIT BREAKER CONNECTIONS. BRANCH CIRCUIT BREAKERS SHALL BE QUICK MAKE, QUICK
AC. ELECTRICAL DRAWINGS ARE INTENDED TO INDICATE APPROXIMATE LOCATIONS OF SWITCHES, C. CONDUIT SYSTEM SHALL BE ELECTRICALLY CONTINUOUS. ALL ENCLOSURES AND NON-CURRENT BREAK, THERMAL MAGNETIC TRIP (ENCLOSURE COMPENSATED), MOLDED CASE TYPE, UL LISTED.
ALL WORK SHALL BE DONE IN ACCORDANCE WITH:
15 AND 20 AMP SINGLE POLE BREAKERS SHALL CARRY THE UL "SWD" MARKING. LINE SIDE
RECEPTACLES, LIGHTING FIXTURES AND OTHER ITEMS OF VARIOUS ELECTRICAL SYSTEMS OF
CARRYING METALS TO BE GROUNDED. ALL LOCK NUTS MUST CUT THROUGH ENAMELED OR
TERMINALS SHALL BE BOLTED TO MAIN BUSBARS. BREAKER RATINGS SHALL BE PER DRAWINGS.
PROJECT. EXACT LOCATIONS AND ROUGH-IN DIMENSIONS FOR ALL WORK AND EQUIPMENT SHALL
PAINTED SURFACES ON ENCLOSURES. WHERE ENCLOSURES AND NON-CURRENT CARRYING
1. THE NATIONAL ELECTRICAL CODE (NFPA 70).
ALL BREAKERS FEEDING HVAC EQUIPMENT SHALL BE HACR RATED, UNLESS NOTED OTHERWISE.
BE OBTAINED FROM ARCHITECT OR ARCHITECT'S REPRESENTATIVE AS WORK PROGRESSES.
METALS ARE ISOLATED FROM THE CONDUIT SYSTEM, USE BONDING JUMPERS WITH APPROVED
2. STATE, CITY, AND COUNTY BUILDING CODES AND ORDINANCES.
SHOULD THE GENERAL CONTRACTOR FAIL TO PROPERLY OBTAIN SUCH LOCATIONS OR DIMENSIONS,
CLAMPS.
3. NATIONAL BOARD OF FIRE UNDERWRITERS (NFPA 72), (NFPA 101).
Y. TERMINALS FOR CONNECTION OF THE FEEDER TO THE PANELBOARD MAINS TO MAIN BREAKER
THE ARCHITECT SHALL CHANGE THIS WORK AT THE GENERAL CONTRACTORS EXPENSE WHEN
4. CERTAIN CODES AND STANDARDS AS SET UP BY VARIOUS TECHNICAL SOCIETIES SUCH AS
SHALL BE UL RECOGNIZED AS SUITABLE FOR THE TYPE OF CONDUCTORS SPECIFIED.
REQUESTED BY ARCHITECT. ARCHITECT RESERVES THE RIGHT TO MAKE MINOR CHANGES IN
D. ALL RECEPTACLES SHALL BE BONDED TO A GROUND CONDUCTOR USING A #12 AWG MINIMUM
UL, NEMA, NECA, IEEE, ASTM, IES, IPCEA, AND ANSI.
LOCATION OF ELECTRICAL WORK OR EQUIPMENT PRIOR TO ROUGHING IN WITH NO ADDITIONAL
BONDING JUMPER BETWEEN RECEPTACLE TERMINAL AND GROUND CONDUCTOR. METAL-TO-METAL
5. THIS WORK SHALL BE GOVERNED ALSO BY LOCAL INSPECTOR'S REQUIREMENTS.
COST TO TENANT. TENANT'S CONSTRUCTION MANAGER RESERVES THE RIGHT TO RELOCATE ANY CONTACT BETWEEN THE DEVICE YOKE AND THE OUTLET BOX IS NOT ACCEPTABLE FOR EITHERZ. NAMEPLATES SHALL BE PROVIDED WITH DESIGNATIONS AS SCHEDULED ON DRAWINGS FOR
6. FEDERAL OCCUPATIONAL SAFETY AND HEALTH ACT STANDARDS.
PANELBOARDS, FEEDER DEVICES, DISTRIBUTION EQUIPMENT AND STARTERS. NAMEPLATES SHAL
OUTLETS OR FIXTURES BEFORE THEY ARE INSTALLED WITHOUT ADDITIONAL COST.
SURFACE MOUNTED BOXES OR FLUSH TYPE BOXES.
7. AMERICANS WITH DISABILITIES ACT.
BE LAMINATED PHENOLIC WITH A WHITE SURFACE AND BLACK CORE.
26 05 00 COMMON WORK RESULTS FOR ELECTRICA
L
B.
H
G
C.
F
D.
LAYOUT: E-701 (480v)
E
E.
D
USER: SHOLLAND
PLOTTED: 7/9/2015 - 12:56 PM
F.
G.
H.
C
I.
B
J.
K.
A
L.
AD. THE ARCHITECT RESERVES THE RIGHT TO DIRECT REMOVAL AND REPLACEMENT OF ANY ITEM WHICH,
E. BOND TRANSFORMER NEUTRAL TO A GROUNDING ELECTRODE SYSTEM.
CONTRACTOR SHALL INQUIRE INTO AND COMPLY WITH ALL APPLICABLE CODES, ORDINANCES, AND IN THEIR OPINION, SHALL NOT PRESENT AN ORDERLY OR REASONABLY NEAT OR WORKMANLIKE
AA. MANUFACTURER: SQUARE D TYPE NQ FOR 208Y/120V APPLICATIONS, TYPE NF FOR 480Y/277V
REGULATIONS. THIS CONTRACTOR SHALL INCLUDE ANY CHANGES REQUIRED BY CODES IN THE BID APPEARANCE, PROVIDED THAT SUCH ITEM CAN BE PROPERLY INSTALLED IN SUCH ORDERLY WAY BY
APPLICATIONS. EQUAL EQUIPMENT BY GENERAL ELECTRIC, SIEMENS, OR CUTLER HAMMER WILL B
F.
THE GROUNDING ELECTRODE CONDUCTOR FOR SEPARATELY DERIVED SYSTEMS, SUCH AS
AND IF THESE CHANGES ARE NOT INCLUDED IN THE BID, THEY MUST BE QUALIFIED AS A SEPARATE METHODS USUAL IN SUCH WORK, OR WHICH DOES NOT COMPLY WITH CONTRACT DRAWINGS OR
DRY-TYPE TRANSFORMERS, SHALL BE RUN IN NON-METALLIC (PVC) CONDUIT TO MINIMIZE GROUNDACCEPTED.
LINE ITEM IN THE BID. AFTER CONTRACT IS ISSUED, NO ADDITIONAL COST DUE TO CODE ISSUES
SPECIFICATIONS. SUCH REMOVALS OR REPLACEMENTS SHALL BE DONE BY CONTRACTOR WHEN SO IMPEDANCE.
SHALL BE REIMBURSED BY TENANT TO THE CONTRACTOR.
AB. EACH PANELBOARD SHALL BE INSTALLED WITH TOP CIRCUIT BREAKER AT 6'-0" ABOVE FLOOR,
DIRECTED IN WRITING BY ARCHITECT AND AT CONTRACTOR'S EXPENSE.
FLUSH
OR SURFACE MOUNTED. ALL FLUSH PANELBOARDS SHALL HAVE (3) 3/4" EMPTY CONDUITS
G. LIGHTING FIXTURES SHALL BE GROUNDED BY THE USE OF A PIGTAIL FASTENED ON BARE METAL
WHERE THE DRAWINGS OR SPECIFICATIONS CALL FOR ITEMS WHICH EXCEED CODES, THE LANDLORD
INSTALLED TO ABOVE ACCESSIBLE CEILING FOR FUTURE USE.
AE. THE ELECTRICAL CONTRACTOR SHALL KEEP ONE SET OF WORKING DRAWINGS ON WHICH ALL
THAT IS FREE OF PAINT.
OR TENANT CRITERIA, THE CONTRACTOR IS RESPONSIBLE FOR FURNISHING AND INSTALLING THE DEVIATIONS, AND CHANGES FROM THE CONTRACT DOCUMENTS, AS WELL AS CONCEALED FEEDER
SYSTEM WITH THE MOST STRINGENT REQUIREMENTS AS DESIGNED AND DESCRIBED ON THESE
AC. ALL CONNECTIONS AT PANELS AND SWITCHES ARE TO BE MADE, ALL SPLICES COMPLETE, ALL
ROUTINGS, SHALL BE RECORDED. THESE DRAWINGS, SHALL NOT BE USED FOR OTHER PURPOSES.
H. BOND ALL STRUCTURAL STEEL TO EARTH, GROUND RODS OR PLATES, OR WATER SYSTEM. BOND
DRAWINGS, UNLESS NOTED OTHERWISE.
FUSES IN PLACE, AND ALL CIRCUITS CONTINUOUS FROM POINT OF SERVICE CONNECTION TO IT'S
THIS SET OF WORKING DRAWINGS SHALL BE DELIVERED TO THE OWNER IN GOOD CONDITION AS A ALL ROOF MOUNTED EQUIPMENT TO ACCEPTABLE GROUNDS PER THE N.E.C.
FINAL DESTINATION, AND ALL COVERS AND PLATES INSTALLED AND FINAL ELECTRICAL INSPECTIO
PERMANENT RECORD OF THE INSTALLATION CONSTRUCTED.
UNLESS SPECIFICALLY NOTED OTHERWISE, MATERIALS, PRODUCTS, AND EQUIPMENT, INCLUDING
PRIOR TO THE TIME OF FINAL INSPECTION BY OWNER'S CONSTRUCTION MANAGER.
ALL COMPONENTS THEREOF, SHALL BE NEW, UNDERWRITERS LABORATORIES LISTED AND LABELED,
AF. THE MATERIALS AND EQUIPMENT INSTALLED IN THE WORK SHALL MEET THE REQUIREMENTS OF THE
MEET OSHA REQUIREMENTS AND SIZED IN CONFORMITY WITH REQUIREMENTS OF THE NATIONAL CONTRACT DOCUMENTS.
AD. TEST AND MAKE CORRECTIONS/ADJUSTMENTS FOR PHASE BALANCING.
ELECTRICAL CODE, STATE AND LOCAL CODES, WHICHEVER IS MORE STRINGENT.
(ELECTRICAL SPECIFICATIONS CONTINUED ON SHEET E-702)
AG. ELECTRICAL CONTRACTOR SHALL SUBMIT SHOP DRAWINGS FOR APPROVAL BEFORE STARTING THE
WORK INVOLVED PER THE DOCUMENTS PROVIDED BY THE TENANT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
#
SEAL
AT
J
Mason, Ohio 45040
RIVERCHASE GALLERIA
A.
K
RIVERCHASE GALLERIA
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #:4933
DRAWN BY:SRH
REVIEWED BY:RAP
AUTHORIZED FOR:
ELECTRICAL
SPECIFICATIONS
2
3
4
A.
B.
C.
D.
E.
J
F.
G.
H.
I.
H
J.
K.
G
L.
F
USER: SHOLLAND
PLOTTED: 7/9/2015 - 12:56 PM
LAYOUT: E-701 (480v)
E
D
C
B
A
6
7
8
9
10
11
J.
27 00 00 GENERAL REQUIREMENTS
12
13
14
WORKSTATION: LABEL CABLES WITHIN OUTLET BOXES AND NEATLY TYPED ON THE INTEGRAL LABEL
IN THE FACEPLATE WITH THE PATCH PANEL PORT NUMBER.
FURNISH AND INSTALL OUTLET BOXES FOR ALL DEVICES AS REQUIRED, (RECEPTACLES, LIGHTING
A. INSTALL ALL WIRING DEVICES, INCLUDING SWITCHES, RECEPTACLES AND POWER RECEPTACLES,
A. PROVIDE ALL MATERIALS, LABOR, TOOLS, TRANSPORTATION INCIDENTALS AND APPURTENANCES
FIXTURES, MOTORS, SYSTEMS EQUIPMENT CONNECTIONS, SPECIAL OUTLETS AND AS OTHERWISE
K. WARRANTY PERIOD FOR COMMUNICATIONS CONNECTIVITY (INCLUDING ALL COPPER):
TELEPHONE OUTLET BOXES, COVER PLATES AND BLANK OUTLET PLATES AS SHOWN OR DESCRIBED
TO COMPLETE IN EVERY DETAIL AND LEAVE IN WORKING ORDER ALL WORK CALLED FOR HEREIN.
REQUIRED).
MANUFACTURER'S STANDARD, BUT NOT LESS THAN 25 YEARS FROM DATE OF CONTRACT
ON DRAWINGS.
COMPLETION.
B. ALL NEW MATERIAL AND EQUIPMENT SHALL MEET THE REQUIREMENTS OF THE FOLLOWING
ALL OUTLET BOXES SHALL BE GALVANIZED PRESSED STEEL, NOT LESS THAN 14 GAUGE IN
B. UNLESS OTHERWISE NOTED ON DRAWINGS OR OTHERWISE REQUIRED BY THE NATIONAL
STANDARDS:
THICKNESS, OF THE STANDARD KNOCKOUT TYPE. NO ROUND OUTLET BOXES SHALL BE PERMITTED,
23 31 11 DIGITAL ADDRESSABLE FIRE ALARM SYSTEM.
1. TELECOMMUNICATIONS INDUSTRY ASSOC./ELECTRONIC INDUSTRIES ALLIANCE (TIA/EIA):
EXCEPT AS SPECIFICALLY NOTED ON DRAWINGS. CONCEALED BOXES SHALL NOT BE LESS THAN 4" ELECTRICAL CODE, ACCESSIBILITY CODES OR LOCAL CODES, OUTLET HEIGHTS SHALL BE AS
FOLLOWS:
a.
TIA/EIA 568A.1, 2, AND 3 TELECOMMUNICATION CABLING STANDARD.
SQUARE AND 1-1/2" DEEP, WITH PLASTER RINGS.
A. EXISTING FIRE ALARM SYSTEM TO REMAIN, SHALL BE UNDER A SEPARATE PERMIT. ALL REQUIRED
b.
TIA/EIA 569 TELECOMMUNICATION PATHWAYS AND SPACES.
FIRE ALARM DEVICES, CONDUITS, WIRES, BACKBOXES, ETC. SHALL BE INSTALLED AT TENANT'S
1. SWITCH HEIGHT 48" FROM FINISHED FLOOR TO CENTERLINE OF OUTLET.
c.
TIA/EIA 606 ADMINISTRATION OF INFRASTRUCTURE
ALL KNOCKOUT BOXES, UPON WHICH LIGHTING FIXTURES ARE TO BE INSTALLED, SHALL BE
EXPENSE UNDER A SEPARATE PERMIT BY MALL FIRE/LIFE SAFETY CONTRACTOR. INDICATE ON PLAN
2. TELEPHONE OUTLETS SHALL BE LOCATED AS NOTED ON DRAWINGS.
d.
TIA/EIA 607 GROUNDING AND BONDING
EQUIPPED WITH 3/8" FIXTURE STUDS.
THAT IS REQUIRED, A VARIANCE WILL BE PROVIDED.
e.
COMPLY WITH TIA/EIA 568, 569, AND BIC STANDARDS.
f.
COMPLY WITH NFPA 70.
RECESSED OUTLET BOXES SHALL BE STAMPED STEEL SUITABLE FOR THE DEVICE INSTALLED. C. DUPLEX RECEPTACLES SHALL BE GROUNDING TYPE, NEMA 5-20R, RATED FOR A 20 AMPS, 125
SURFACE MOUNTED OUTLET BOXES SHALL BE CAST IRON SUITABLE FOR THE DEVICE INSTALLED. VOLTS, WITH PROVISIONS FOR BACK AND SIDE WIRING.GROUND FAULT CIRCUIT INTERRUPTER
DUPLEX RECEPTACLES SHALL BE PROVIDED WHERE INDICATED.
C. THE CONTRACTOR SHALL BEAR ALL COSTS OF PERMITS, INSPECTIONS TESTS, AND/OR APPROVALS.
EXTERIOR BOXES SHALL BE CAST ALUMINUM TYPE WITH GASKETED DEVICE COVERS TO SUIT. D. SWITCHES SHALL BE TOGGLE OPERATED, QUIET TYPE, RATED FOR 20 AMPS, 120/277 VOLTS, WITH
PROVISIONS FOR BACK AND SIDE WIRING. THREE WAY AND FOUR WAY SWITCHES SHALL BE
D. THE CONTRACTOR SHALL PROVIDE ON-SITE PERSONNEL TO TROUBLESHOOT AND REPAIR ANY
PROVIDED WHERE INDICATED.
PROBLEMS THAT ARISE DURING CUTOVER AS THEY RELATE TO THEIR INSTALLED SYSTEM.
INSTALL BOXES RIGIDLY FROM BUILDING STRUCTURE AND SUPPORT INDEPENDENTLY OF THE
CONDUIT SYSTEM. ALSO PROVIDE SUITABLE BOX EXTENSIONS TO EXTEND BOXES TO FINISHEDE. DIMMERS SHALL BE LUTRON "NOVA T-STAR" SERIES, OF A RATING, VOLTAGE AND WATTAGE
SUITABLE FOR LOAD SERVED.
E. AFTER COMPLETION, A WARRANTY SHALL BE FURNISHED FOR ALL COMPONENTS, PARTS, AND
FACES OF FLOORS, CEILINGS, WALLS ETC. ALL OUTLET BOXES TO BE PROVIDED WITH CADDY
F. COLORS OF DEVICES SHALL MATCH WALL.
ASSEMBLIES AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP. WARRANTY SERVICES SHALL
"QUICK-MOUNT BOX SUPPORT" TO MINIMIZE THE DEFLECTION THAT OCCURS WHEN
G. WIRING DEVICES SHALL BE SPECIFICATION GRADE, AS MANUFACTURED BY HUBBELL, PASS &
BE PROVIDED BY A CERTIFIED, FACTORY TRAINED REPRESENTATIVE OF THE EQUIPMENT
PLUGGING/UNPLUGGING INTO THESE DEVICES.
SEYMOUR, ARROW HART, LEVITON AND GENERAL ELECTRIC.
MANUFACTURER FOR A MINIMUM OF ONE YEAR OR AS SPECIFIED IN EACH INDIVIDUAL SECTION.
ALL ELECTRICAL CONDUCTORS SHALL BE ENCLOSED IN CONTINUOUS GROUNDED RACEWAY H. FLOOR RECEPTACLES SHALL BE HUBBELL "SYSTEMONE" SERIES FOR FLUSH FLOOR APPLICATIONS.
27 05 10 TELEPHONE AND DATA CONDUIT SYSTEM
SYSTEM EXCEPT AS OTHERWISE NOTED (I.E. LOW-VOLTAGE PLENUM-RATED WIRE).
a. FLOOR BOX - MODEL S1PFB NON-METALLIC ROUND FLOOR BOX
A. FURNISH AND INSTALL A SYSTEM OF CONDUIT RACEWAYS, OUTLET BOXES, PULL WIRES, AND
b.
POKE-THRU - MODEL S1PTFIT THRU-FLOOR FITTING (DUAL CHANNEL)
NO OTHER CIRCUITS ARE TO BE RUN IN SAME CONDUIT FEEDING ISOLATED GROUND RECEPTACLES.
TERMINAL BOARDS AS SHOWN ON THE DRAWINGS UNLESS OTHERWISE NOTED ON PLANS.
c.
SUB PLATE - MODEL S1SP SUB-PLATE(STYLE LINE/GFCI)
TELEPHONE SWITCHING APPARATUS, CONDUCTORS, INSTRUMENTS, MISCELLANEOUS EQUIPMENT
RACEWAY AND ENCLOSURE SIZES SHALL BE AS SHOWN ON DRAWINGS OR, IF NOT SHOWN, SHALL
d.
COVER - MODEL S1TFCAL (ALUMINUM FINISH).
AND APPURTENANCES ARE NOT PART OF THIS CONTRACT AND WILL BE PROVIDED AND INSTALLED
BE SIZED TO COMPLY WITH N.E.C. FILL REQUIREMENTS FOR CONDUCTORS ENCLOSED.
OTHER EQUIVALENT DEVICES WITH MATCHING COVER PLATES MAY BE FURNISHED AS APPROVED BY OTHERS.
PULL OR JUNCTION BOXES SHALL BE PROVIDED IN ALL RACEWAY SYSTEMS AT MAXIMUM OF 100
BY OWNER'S.
B.
CONDUITS
FOR TELEPHONE WALL OUTLETS AND DATA WIRING SHALL BE A MINIMUM OF 1" UNLESS
FOOT INTERVALS AND WHERE REQUIRED TO AVOID EXCESSIVE NUMBER OF BENDS, TO FACILITATE
WIRE PULLING OR TO PROVIDE ACCESS TO RACEWAY SYSTEM. BOXES AND COVERS SHALL BE I.
WIRING DEVICES, UNLESS OTHERWISE PROPERLY AUTHORIZED, SHALL BE SAME MANUFACTURERSNOTED OTHERWISE.
GALVANIZED STEEL OF CODE GAUGE SIZE. TO THE EXTENT POSSIBLE, AVOID THE USE OF JUNCTION
ONLY; NO ADDITIONAL MANUFACTURERS SHALL BE PERMITTED UNLESS SPECIFICALLY
C. FURNISH AND INSTALL A 3/4" THICK, FIRE-TREATED, PLYWOOD TELECOM BACKBOARD AT LOCATION
BOXES IN INACCESSIBLE LOCATIONS. THE USE OF JUNCTION BOXES ABOVE DRYWALL CEILINGS
AUTHORIZED BY TENANT OR TENANT'S REPRESENTATIVE.
SHOWN ON THE DRAWINGS. PAINT WITH FIRE RETARDANT "P-1B" OR AS DIRECTED BY TENANT'S
SHALL BE LIMITED TO LOCATIONS NEAR ACCESS FRAMES USED FOR DIFFUSERS AND RETURN AIR
CONSTRUCTION MANAGER. THE PLYWOOD BACKBOARD SHALL BE SECURELY ATTACHED TO THE
GRILLES OR ACCESS PANELS AS LOCATED ON PLANS. JUNCTION AND PULL BOXES MUST BE
J. LOW VOLTAGE CONTROL DEVICES SHALL BE AS NOTED ON DRAWINGS OR AS REQUIRED.
BUILDING WALLS TO SUPPORT RELAY PANELS, TERMINAL BLOCKS AND OTHER HARDWARE WEIGHING
LABELED WITH CIRCUIT NUMBER IDENTIFICATION AND SYSTEM TYPE ON COVER.
APPROXIMATELY 10 POUNDS PER SQUARE FOOT.
26 29 13 MOTOR CONTROLLERS
RACEWAYS AND ENCLOSURES SHALL BE ADEQUATELY SUPPORTED FROM BUILDING STRUCTURE
D.
ALL CONDUIT RUNS FOR DATA AND TELEPHONE SHALL BE CONTINUOUS WITH NO JUNCTION BOXES
WITH APPROVED SUPPORT RODS AND/OR CLAMPS IN ACCORDANCE WITH ARTICLE 300.7 OF THE
A. GENERAL CONTRACTOR SHALL FURNISH AND INSTALL ALL MOTOR CONTROLS, INCLUDING
EXCEPT AS NOTED ON DRAWINGS. THIS INCLUDES BUT IS NOT LIMITED TO RUNS BETWEEN
NATIONAL ELECTRIC CODE.
STARTERS, SAFETY DEVICES AND REMOTE CONTROL STATIONS, UNLESS FURNISHED BY
TELEPHONE BOARD, MANAGER'S OFFICE, SOUND SYSTEM, CASHWRAPS AND TELEPHONE SETS.
EQUIPMENT MANUFACTURER IN PRE-WIRED ASSEMBLIES.
ALL CONDUIT SHALL BE RIGID HEAVYWALL GALVANIZED STEEL OR THIN WALL EMT WHERE PERMITTED
E. INSTALL PULL STRING IN EMPTY CONDUITS. ALL CONDUITS SHALL BE LABELED FOR PURPOSE
BY CODE OR AS HEREINAFTER SPECIFIED. PVC SCHEDULE 80 CONDUIT MAY BE USED UNDER B. FURNISH AND INSTALL MANUAL MOTOR STARTERS WITH OVERLOAD RELAYS IN EACH LINE
DESIGNATED.
FLOOR SLAB. ROMEX, BX OR AC, ETC., ARE NOT PERMITTED.
CONDUCTOR FOR ALL FRACTIONAL HORSEPOWER MOTORS NOT EQUIPPED WITH BUILT-IN RUNNING
OVERCURRENT PROTECTION, NOT REQUIRING AUTOMATIC CONTROLLERS.
F. FURNISH AND INSTALL GROUND ROD AND #6 GROUND WIRE FROM TELECOM BACKBOARD TO
M. MINIMUM SIZE OF CONDUIT SHALL BE 1/2" FOR INDIVIDUAL LIGHTING FIXTURE CONNECTIONS OR
TO INDIVIDUAL LIGHT SWITCHES (IF ACCEPTABLE BY THE LANDLORD AND LOCAL CODE OFFICIALS)
C. MANUAL MOTOR STARTERS SHALL INCLUDE OVERLOAD RELAYS IN ALL LINE POLES SIZED TO TRIP SERVICE ENTRANCE GROUND AND GROUND ROD PER TELEPHONE COMPANY'S REQUIREMENTS.
AND 3/4" FOR ALL OTHER LOCATIONS. IF HVAC CONTROL WIRING IS REQUIRED TO BE RUN IN
SWITCH AT 125% OF MOTOR FULL LOAD RUNNING CURRENT, NEON PILOT LIGHTS, AND NEMA
G. OUTLET BOXES TO BE 4" SQUARE MINIMUM WITH SINGLE DEVICE COVER AND TELEPHONE PLATE.
CONDUIT, IT SHALL BE A MINIMUM OF 1/2", UNLESS NOTED OTHERWISE ON DRAWINGS. ALL
ENCLOSURES, AS MANUFACTURED BY SQUARE-D, GENERAL ELECTRIC, ALLEN BRADLEY, SIEMEN'S
IN/UNDER FLOOR CONDUIT SHALL BE OF MINIMUM 1" SIZE.
OR CUTLER HAMMER.
27 05 15 INTERIOR COMMUNICATIONS PATHWAYS
N. EMT THIN WALL CONDUIT MAY BE USED INSIDE HOLLOW PARTITIONS, AND ABOVE SUSPENDED D. FURNISH AND INSTALL AUTOMATIC MOTOR STARTERS FOR ONE (1) HP OR LARGER SINGLE PHASE
A. INTERIOR COMMUNICATIONS PATHWAYS SHALL BE INSTALLED BY THE GENERAL CONTRACTOR AND
CEILINGS AND EXPOSED ABOVE 8'-0" ABOVE FINISHED FLOOR OR ABOVE PANELBOARDS. EMT
AND THREE PHASE MOTORS OR MOTORIZED EQUIPMENT FURNISHED WITHOUT STARTERS,
BY THE TELECOMMUNICATIONS CONTRACTOR AS SPECIFIED HEREIN.
CONDUIT MAY NOT BE USED BURIED IN EARTH OR FILL, IN OR UNDER CONCRETE FLOOR OR IN
REQUIRINGAUTOMATIC STARTERS FOR CONTROL REGARDLESS OF HORSEPOWER RATING. ALL
POURED CONCRETE CONSTRUCTION.
THREE PHASE STARTERS SHALL HAVE ANTI-SINGLE PHASING, UNDERVOLTAGE PROTECTION, AND
B. CONDUITS SHALL BE INSTALLED, AS DETAILED IN DRAWINGS. THESE CONDUITS SHALL BE
PHASE REVERSAL PROTECTION RELAYS EITHER INCLUDED IN STARTERS OR WIRED TO STARTER INSTALLED BY THE GENERAL CONTRACTOR.
O. PVC CONDUIT USED UNDER FLOOR SLABS SHALL HAVE RIGID GALVANIZED STEEL ELLS AND
CONTROL CIRCUIT.
METALLIC CONDUIT ABOVE FLOOR SLAB.
E. PROTECTIVE RELAYS SHALL HAVE ADJUSTABLE TIME DELAY RELAY IN CIRCUIT TO AVOID NUISANCE
27 11 00 HORIZONTAL CABLING AND CONNECTIVITY
P. FLEXIBLE METAL CONDUIT (FMC) SHALL BE USED ONLY FOR CONNECTIONS INSIDE CASEWORK ANDSHUT DOWNS. TIME MARK OR SIMILAR EQUIPMENT IS ACCEPTABLE, IF PROTECTION IS NOT PART
A. PROVIDE A 10/100/1000 MBPS FULL-DUPLEX TRANSMISSION ETHERNET NETWORK OVER 4-PAIR,
AS THE FINAL CONNECTION TO RECESSED FIXTURES, MOTORS, AND ELECTRICAL EQUIPMENT THATOF STARTER. DO NOT RELY ON PROPERLY SIZED FUSES AND MOTOR STARTER OVERLOAD HEATERS
CATEGORY 5E UTP HORIZONTAL CABLING. THE SYSTEM SHALL BE A CERTIFIED SOLUTION BY THE
MAY GENERATE VIBRATION THROUGH THE CONDUIT SYSTEM. FMC SHALL BE UL APPROVED, AND ALONE TO AVOID SINGLE PHASING BURNOUTS.
CONNECTIVITY MANUFACTURER. THE HORIZONTAL INFRASTRUCTURE SHALL SUPPORT BOTH VOICE
BOTH THE CONDUIT AND FITTINGS SHALL BE LISTED FOR GROUNDING. FMC SHALL BE KEPT TO F.
SIX FURNISH AND INSTALL CONTACTORS, CONTROL RELAYS, PUSHBUTTON STATIONS, SELECTOR
AND DATA APPLICATIONS.
FEET (6'-0") MAXIMUM LENGTH AND SHALL BE MINIMUM ONE-HALF INCH (1/2") ELECTRICAL TRADE SWITCHES, PILOT LIGHTS, FUSES AND SIMILAR CONTROL AUXILIARIES AS SHOWN ON DRAWINGS
AND/OR REQUIRED TO PROVIDE PROPER CONTROL AND ISOLATION BETWEEN VARIOUS AUTOMATIC
SIZE. WHEN CONNECTED TO HARD CONDUIT, THE FMC MUST BE THE SAME SIZE AS THE HARD
B. THIS SECTION INCLUDES WIRE, CABLE, CONNECTING DEVICES, INSTALLATION, AND TESTING FOR
CONTROLLERS
AND
EQUIPMENT
SHOWN
ON
THE
DRAWINGS.
CONDUIT IT IS CONNECTED TO. AN EQUIPMENT GROUNDING CONDUCTOR MUST BE INSTALLED IN
WIRING SYSTEMS TO BE USED AS SIGNAL PATHWAYS FOR VOICE, VIDEO, AND DATA
ALL RUNS OF FMC.
TRANSMISSION. THE SYSTEM SHALL INCLUDE BUT NOT BE LIMITED TO THE FOLLOWING:
G. ALL CIRCUIT BREAKERS FEEDING MOTOR LOADS SHALL BE HACR TYPE.
1. MOUNTING ELEMENTS
Q. LIQUID-TIGHT FLEXIBLE METAL CONDUIT (LFMC) AND LIQUID-TIGHT FITTINGS SHALL BE USED IN
2. UNSHIELDED TWISTED-PAIR CABLE.
AREAS EXPOSED TO THE WEATHER OR EXCESSIVE MOISTURE AS THE FINAL CONNECTION TO H. EQUIPMENT SHALL BE SAME MAKE AS MOTOR STARTERS. PUSHBUTTON STATIONS, SELECTOR
3.
PATCH, STATION, AND CROSS CONNECT CORDS
MOTORS, AND ELECTRICAL EQUIPMENT THAT MAY GENERATE VIBRATION THROUGH THE CONDUIT SWITCHES, PILOT LIGHTS: HEAVY DUTY, OIL TIGHT, STANDARD SIZE, WITH TRANSFORMER TYPE 4. JACKS AND FACEPLATES
SYSTEM. LFMC SHALL BE UL APPROVED, AND BOTH THE CONDUIT AND FITTINGS SHALL BE LISTED PILOT LIGHTS, FLUSH MOUNTED WHERE PRACTICAL.
5. TERMINATION AND PATCH PANELS
FOR GROUNDING. LFMC SHALL BE KEPT TO SIX FEET (6'-0") MAXIMUM LENGTH AND SHALL BE
I.
ALL
OVERLOAD
DEVICES,
INCLUDING
EQUIPMENT
FURNISHED
UNDER
OTHER
CONTRACTS,
SHALL
BE
MINIMUM ONE-HALF INCH (1/2") ELECTRICAL TRADE SIZE. WHEN CONNECTED TO HARD CONDUIT,
C. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE PRODUCTS BY ONE
THE LFMC MUST BE THE SAME SIZE AS THE HARD CONDUIT IT IS CONNECTED TO. AN EQUIPMENT SET AND ADJUSTED TO SUIT THE LOAD CONDITIONS.
OF THE FOLLOWING:
GROUNDING CONDUCTOR MUST BE INSTALLED IN ALL RUNS OF LFMC.
1. COPPER CABLES (UTP):
26 51 00 INTERIOR LIGHTING
a. BERK-TEK, INC.
R. ALL CONDUIT IN EXPOSED AREAS SHALL BE CONCEALED. CONDUIT SMALLER THAN 3/4' SHALL NOT
A. INSTALL LIGHTING FIXTURES SPECIFIED ON THE FIXTURE SCHEDULE AND SHOWN ON THE DRAWINGS. b.
BELDEN
BE USED FOR ANY CIRCUIT HOMERUN. NO CONDUIT SHALL BE RUN IN SLAB, EXCEPT AS REQUIRED
c. MOHAWK
FOR FLOOR-MOUNTED DEVICES. PROVIDE PROPERLY LABELED PULL STRING IN ALL EMPTY
B. ALL FIXTURES TO BE LISTED AND LABELED BY UNDERWRITERS LABORATORIES AND ALL BALLASTS
d.
GENERAL
CONDUITS.
TO BE CBM CERTIFIED BY ETL.
e. UNIPRISE
2. MODULAR JACKS & FACEPLATES:
S. EXPOSED CONDUIT WILL BE PERMITTED IN ELECTRIC ROOMS, AND SIMILAR UNFINISHED SPACES,
C. EMERGENCY LIGHTING AS INDICATED, SHALL PROVIDE A MINIMUM OF ONE FOOT-CANDLE ALONG
a. LEVITON
OVERHEAD IN AREAS WITHOUT CEILINGS AND ELSEWHERE AT THE DISCRETION OF THE ARCHITECT.
THE PATH OF EGRESS. FIXTURE SUPPLIER SHALL PROVIDE FOOT-CANDLE PRINTOUT TO VERIFY
b. HUBBELL
EMERGENCY LIGHT LEVELS.
c.
ORTRONICS
T. ALL CONDUIT FITTINGS SHALL BE GALVANIZED MALLEABLE IRON OR STEEL. CONNECTORS AND
d.
PANDUIT
COUPLINGS SHALL BE THREADED OR CUPPED SET SCREW TYPE, CONCRETE TIGHT. CONDUIT
D. FIXTURES ARE TO BE PROVIDED COMPLETE WITH BALLASTS, SOCKET, LAMPS, END AND TRIP
e. UNIPRISE
BODIES SHALL BE MALLEABLE IRON, THREADED FOR HEAVYWALL CONDUIT AND CUPPED SET
PLATES
AND
ALL
MOUNTING
ACCESSORIES
REQUIRED
FOR
A
COMPLETE
FIXTURE
INSTALLATION.
SCREW TYPE FOR EMT, WITH CADMIUM FINISH AND CADMIUM PLATED SHEET STEEL COVERS.
D. HORIZONTAL CABLES FOR VOICE/DATA/VIDEO INFRASTRUCTURE:
SYNTHETIC RUBBER GASKETS SHALL BE USED UNDER BODY COVERS EXPOSED TO WEATHER. EMT
E. INCANDESCENT AND HIGH INTENSITY DISCHARGE RECESSED LIGHTING FIXTURES TO BE FURNISHED
CONNECTORS SHALL BE INSULATED THROAT TYPE.
1. LISTED AS COMPLYING WITH CATEGORY 5E OF TIA/EIA-568-A.
WITH THERMAL CUT OUTS AS REQUIRED BY THE NEC.
2. CONDUCTORS: SOLID COPPER.
U. INSTALL EXPANSION FITTINGS AT ALL LOCATIONS WHERE CONDUITS CROSS BUILDING EXPANSION
3. UTP CABLE: COMPLY WITH TIA/EIA-568-A. FOUR THERMOPLASTIC-INSULATED, INDIVIDUALLY
F. BALLASTS SHALL BE INSTANT-START, ELECTRONIC TYPE, CLASS P, "A" SOUND RATING AND
JOINTS OR TRAVERSE FROM ONE INDEPENDENT STRUCTURE TO ANOTHER. INSTALL WHEREVER
TWISTED PAIR OF CONDUCTORS; NO. 2 AWG, COLOR-CODED; ENCLOSE IN A JACKET.
MAXIMUM HARMONIC CONTENT OF 10%. DIMMING BALLASTS SHALL BE 3-WIRE TYPE, WITH
CONDUITS TRAVERSE STRUCTURES HAVING SEPARATE FOUNDATIONS OR WHERE EXISTING
4. CABLE RATING: PLENUM - LISTED FOR USE IN AIR-HANDLING SPACES,
DIMMING
CAPABILITY
TO
10%
OF
FULL
RATED
OUTPUT.
UNLESS
NOTED
OTHERWISE.
FURNISH
BUILDINGS ARE JOINED TO A NEW STRUCTURE.
5. NON-PLENUM IN ALL OTHER AREAS.
SPECIAL LOW TEMPERATURE BALLASTS FOR EXTERIOR MOUNTED FIXTURES.
6. COLOR CODING: BLUE FOR DATA, YELLOW FOR VOICE AND WHITE FOR VIDEO
V. DURING ROUGHING-IN, CAP ALL CONDUITS WHICH MAY BECOME FOULED WITH FOREIGN MATERIAL.
G. FLUORESCENT LAMPS SHALL BE 3500k. INCANDESCENT LAMPS SHALL BE 130 VOLT. HIGH
E. WORKSTATION OUTLETS: SINGLE JACK CONNECTOR ASSEMBLIES MOUNTED IN FACEPLATE.
W. NO MORE THAN THREE (3) 90 DEGREE BENDS WILL BE ALLOWED IN ANY ONE CONDUIT RUN. WHEREINTENSITY DISCHARGE LAMPS SHALL BE COATED.
3
4
5
6
7
8
9
10
11
SEAL
SPACE #236A
2.0 TYPE: PREMIUM
SGH STORE #:4933
DRAWN BY:SRH
REVIEWED BY:RAP
AUTHORIZED FOR:
ELECTRICAL
SPECIFICATIONS
PATCH PANEL PORT NUMBER. LABEL EACH CABLE WITHIN 3 INCHES OF EACH TERMINATION, WHERE
IT IS ACCESSIBLE IN A CABINET OR JUNCTION OR OUTLET BOX, AND ELSEWHERE AS INDICATED.
2
#
RIVERCHASE GALLERIA
MORE BENDS ARE NECESSARY IN ANY SINGLE RUN, A PULL BOX SHALL BE INSTALLED. ALL CONDUIT
1. FACEPLATE: HIGH IMPACT PLASTIC; COLOR TO BE WHITE.
H. ALL RECESSED HID FIXTURES SHALL CARRY A ULR LISTING. THEY SHALL HAVE A THERMAL CUT OUT
EXCEPT IN CONCRETE SLAB OR EARTH SHALL BE ROUTED PARALLEL OR PERPENDICULAR TO THE
2. MOUNTING: FLUSH, UNLESS OTHERWISE INDICATED.
ON BOTH THE BALLAST AND THE FIXTURE ITSELF.
LINES OF THE BUILDING, AND NO OUT-OF-PLUMB OR DIAGONAL LINES WILL BE ACCEPTED.
3. LABELING: SHALL HAVE INTEGRAL LABEL WITH LABEL COVER.
4. JACK SPACES: AS INDICATED ON THE DRAWINGS WITH ANY NECESSARY BLANKS.
I. USE STEEL WIRE HANGERS FASTENED TO THE BUILDING STRUCTURE TO SUPPORT RECESSED
26 09 23 LIGHTING CONTROLS
BLANKS SHALL MATCH FACEPLATE COVER.
FIXTURES AT EACH CORNER. (FOUR CORNER SUSPENDED). FIXTURES TO FIT TIGHT AGAINST
A. WHERE LIGHTING CONTACTORS ARE INDICATED ON THE DRAWINGS, THEY WILL BE FURNISHED ANDCONSTRUCTION TO ELIMINATE LIGHT LEAKS.
F. WIRING METHOD: INSTALL HORIZONTAL CABLING IN RACEWAY WITHIN RACKS AND ENCLOSURES,
INSTALLED BY ELECTRICAL CONTRACTOR COMPLETE WITH CONDUIT. THE ELECTRICAL CONTRACTOR
WILL BE RESPONSIBLE TO INSTALL THE CONTACTORS AND PULL ALL WIRES AS DETAILED ON THESE
J. WALL-MOUNTED FIXTURES SHALL BE MOUNTED PLUMB WITH BUILDING LINES AND INSTALLED WITHAND EXCEPT IN ACCESSIBLE CEILING SPACES AND IN GYPSUM BOARD PARTITIONS WHERE CABLE
WIRING METHOD MAY BE USED. CONCEAL RACEWAY AND CABLING EXCEPT IN UNFINISHED SPACES.
DRAWINGS AND CIRCUITED EXACTLY AS DIAGRAMMED ON THE ELECTRICAL DETAIL DRAWINGS. NO PROPER BOX AND COVER HARDWARE.
IN ACCESSIBLE CEILINGS, USE APPROPRIATELY SIZED J-HOOKS TO SUPPORT THE CABLING EVERY
VARIATIONS TO THE CIRCUITING ARE ALLOWED.
K. SURFACE-MOUNTED FIXTURES SHALL COVER MOUNTING HARDWARE. USE A CANOPY THAT IS NO FOUR FEET (MAXIMUM).
26 22 00 LOW VOLTAGE TRANSFORMERS
LONGER THAN THE LENGTH AND WIDTH OF THE FIXTURE AND AT A HEIGHT THAT IS NO HIGHER THAN
G. INSTALL CABLE USING TECHNIQUES, PRACTICES, AND METHODS THAT ARE CONSISTENT WITH
REQUIRED
TO
MOUNT
FIXTURE
ABSOLUTELY
VERTICAL.
CANOPY
FINISH
SHALL
MATCH
FIXTURE
A. DRY TYPE DISTRIBUTION TRANSFORMER IS EXISTING TO BE RELOCATED.
CATEGORY 5E RATING OF COMPONENTS AND THAT INSURE CATEGORY 5E PERFORMANCE OF
FINISH.
COMPLETED AND LINKED SIGNAL PATHS, END TO END.
B. THIS CONTRACTOR IS TO BALANCE THE VOLTAGE LEAVING THE STEP-DOWN TRANSFORMER TO
PROVIDE A SECONDARY VOLTAGE OF 120 MINIMUM TO 125 VOLTS MAXIMUM BY ADJUSTING THEL. STEM-MOUNTED FIXTURES SHALL BE MOUNTED SO AS TO BE ABSOLUTELY VERTICAL AND
H. DO NOT BEND CABLE IN HANDLING OR IN INSTALLING TO SMALLER RADII THAN MINIMUMS
TRANSFORMER TAPS ONCE ALL THE FINAL CONNECTIONS HAVE BEEN MADE TO THE LOW VOLTAGEHORIZONTAL. INSTALL AND SUPPORT AS SHOWN ON DRAWINGS.
RECOMMENDED BY MANUFACTURER.
PANELBOARD. PROVIDE FINAL BALANCE REPORT TO OWNER'S CONSTRUCTION MANAGER AT TIME
OF PUNCH-OUT.
I. HORIZONTAL CABLES: LABEL CABLES AT THE WORK AREA END AND AT THE CLOSET END WITH THE
1
Mason, Ohio 45040
AT
K
5
26 27 26 WIRING DEVICES
RIVERCHASE GALLERIA
1
26 05 33 RACEWAY AND BOXES FOR ELECTRICAL SYSTEMS
12
13
14

4933 Bid Set.dwf - SRC Services, Inc.

Transcription

Similar documents

CSAH 5 Newletter - Sherburne County

hafeilobopartsmanual

Managing Contractor Owned Equipment Leased To the Owner`s

EPC-A-1 Emergency Power Relay

1 - City of Laredo

Nelnet Professional Services Agreement (04/25/2012)

Britco Supplies Disaster Relief Housing for Save the Children

Amendment

CHEMTONE MASONRY STAIN

PERSPECTIVE VIEWS OF OBJECTS